LM2831
LM2831 High Frequency 1.5A Load - Step-Down DC-DC Regulator
Literature Number: SNVS422A
LM2831
High Frequency 1.5A Load - Step-Down DC-DC
Regulator
General Description
The LM2831 regulator is a monolithic, high frequency, PWM
step-down DC/DC converter in a 5 pin SOT23 anda6Pin
LLP package. It provides all the active functions to provide
local DC/DC conversion with fast transient response and
accurate regulation in the smallest possible PCB area. With
a minimum of external components, the LM2831 is easy to
use. The ability to drive 1.5A loads with an internal 130 m
PMOS switch using state-of-the-art 0.5 µm BiCMOS technol-
ogy results in the best power density available. The world-
class control circuitry allows on-times as low as 30ns, thus
supporting exceptionally high frequency conversion over the
entire 3V to 5.5V input operating range down to the minimum
output voltage of 0.6V. Switching frequency is internally set
to 550 kHz, 1.6 MHz, or 3.0 MHz, allowing the use of
extremely small surface mount inductors and chip capaci-
tors. Even though the operating frequency is high, efficien-
cies up to 93% are easy to achieve. External shutdown is
included, featuring an ultra-low stand-by current of 30 nA.
The LM2831 utilizes current-mode control and internal com-
pensation to provide high-performance regulation over a
wide range of operating conditions. Additional features in-
clude internal soft-start circuitry to reduce inrush current,
pulse-by-pulse current limit, thermal shutdown, and output
over-voltage protection.
Features
nSpace Saving SOT23-5 Package
nInput voltage range of 3.0V to 5.5V
nOutput voltage range of 0.6V to 4.5V
n1.5A output current
nHigh Switching Frequencies
1.6MHz (LM2831X)
0.55MHz (LM2831Y)
3.0MHz (LM2831Z)
n130mPMOS switch
n0.6V, 2% Internal Voltage Reference
nInternal soft-start
nCurrent mode, PWM operation
nThermal Shutdown
nOver voltage protection
Applications
nLocal 5V to Vcore Step-Down Converters
nCore Power in HDDs
nSet-Top Boxes
nUSB Powered Devices
nDSL Modems
Typical Application Circuit
20174864
20174881
August 2006
LM2831 High Frequency 1.5A Load - Step-Down DC-DC Regulator
© 2006 National Semiconductor Corporation DS201748 www.national.com
Connection Diagrams
20174801
6-Pin LLP
20174803
5-Pin SOT-23
Ordering Information
Order Number Frequency
Option Package Type NSC Package
Drawing Top Mark Supplied As
LM2831XMF
1.6MHz
SOT23-5 MF05A SKYB 1000 units Tape and Reel
LM2831XMFX 3000 units Tape and Reel
LM2831XSD LLP-6 SDE06A L193B 1000 units Tape and Reel
LM2831XSDX 4500 units Tape and Reel
LM2831YMF
0.55MHz
SOT23-5 MF05A SKZB 1000 units Tape and Reel
LM2831YMFX 3000 units Tape and Reel
LM2831YSD LLP-6 SDE06A L194B 1000 units Tape and Reel
LM2831YSDX 4500 units Tape and Reel
LM2831ZMF
3MHz
SOT23-5 MF05A SLAB 1000 units Tape and Reel
LM2831ZMFX 3000 units Tape and Reel
LM2831ZSD LLP-6 SDE06A L195B 1000 units Tape and Reel
LM2831ZSDX 4500 units Tape and Reel
NOPB versions available as well
LM2831
www.national.com 2
Pin Descriptions 5-Pin SOT23
Pin Name Function
1 SW Output switch. Connect to the inductor and catch diode.
2 GND Signal and power ground pin. Place the bottom resistor of the feedback network as close as
possible to this pin.
3 FB Feedback pin. Connect to external resistor divider to set output voltage.
4 EN Enable control input. Logic high enables operation. Do not allow this pin to float or be
greater than VIN + 0.3V.
5 VIN Input supply voltage.
Pin Descriptions 6-Pin LLP
Pin Name Function
1 FB Feedback pin. Connect to external resistor divider to set output voltage.
2 GND Signal and power ground pin. Place the bottom resistor of the feedback network as
close as possible to this pin.
3 SW Output switch. Connect to the inductor and catch diode.
4 VIND Power Input supply.
5 VINA Control circuitry supply voltage. Connect VINA to VIND on PC board.
6 EN Enable control input. Logic high enables operation. Do not allow this pin to float or be
greater than VINA + 0.3V.
DAP Die Attach Pad Connect to system ground for low thermal impedance, but it cannot be used as a
primary GND connection.
LM2831
www.national.com3
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
VIN -0.5V to 7V
FB Voltage -0.5V to 3V
EN Voltage -0.5V to 7V
SW Voltage -0.5V to 7V
ESD Susceptibility 2kV
Junction Temperature (Note 2) 150˚C
Storage Temperature −65˚C to +150˚C
Soldering Information
Infrared or Convection Reflow
(15 sec) 220˚C
Operating Ratings
VIN 3V to 5.5V
Junction Temperature −40˚C to +125˚C
Electrical Characteristics VIN = 5V unless otherwise indicated under the Conditions column. Limits in
standard type are for T
J
= 25˚C only; limits in boldface type apply over the junction temperature (T
J
) range of -40˚C to
+125˚C. Minimum and Maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent
the most likely parametric norm at T
J
= 25˚C, and are provided for reference purposes only.
Symbol Parameter Conditions Min Typ Max Units
V
FB
Feedback Voltage LLP-6 and SOT23-5
Package
0.588 0.600 0.612 V
V
FB
/V
IN
Feedback Voltage Line Regulation V
IN
= 3V to 5V 0.02 %/V
I
B
Feedback Input Bias Current 0.1 100 nA
UVLO Undervoltage Lockout V
IN
Rising 2.73 2.90 V
V
IN
Falling 1.85 2.3
UVLO Hysteresis 0.43 V
F
SW
Switching Frequency
LM2831-X 1.2 1.6 1.95
MHzLM2831-Y 0.4 0.55 0.7
LM2831-Z 2.25 3.0 3.75
D
MAX
Maximum Duty Cycle
LM2831-X 86 94
%LM2831-Y 90 96
LM2831-Z 82 90
D
MIN
Minimum Duty Cycle
LM2831-X 5
%LM2831-Y 2
LM2831-Z 7
R
DS(ON)
Switch On Resistance LLP-6 Package 150 m
SOT23-5 Package 130 195
I
CL
Switch Current Limit V
IN
= 3.3V 1.8 2.5 A
V
EN_TH
Shutdown Threshold Voltage 0.4 V
Enable Threshold Voltage 1.8
I
SW
Switch Leakage 100 nA
I
EN
Enable Pin Current Sink/Source 100 nA
I
Q
Quiescent Current (switching)
LM2831X V
FB
= 0.55 3.3 5mA
LM2831Y V
FB
= 0.55 2.8 4.5
LM2831Z V
FB
= 0.55 4.3 6.5
Quiescent Current (shutdown) All Options V
EN
=0V 30 nA
LM2831
www.national.com 4
Electrical Characteristics VIN = 5V unless otherwise indicated under the Conditions column. Limits in
standard type are for T
J
= 25˚C only; limits in boldface type apply over the junction temperature (T
J
) range of -40˚C to
+125˚C. Minimum and Maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent
the most likely parametric norm at T
J
= 25˚C, and are provided for reference purposes only. (Continued)
Symbol Parameter Conditions Min Typ Max Units
θ
JA
Junction to Ambient
0 LFPM Air Flow (Note 3)
LLP-6 Package 80 ˚C/W
SOT23-5 Package 118
θ
JC
Junction to Case (Note 3) LLP-6 Package 18 ˚C/W
SOT23-5 Package 80
T
SD
Thermal Shutdown Temperature 165 ˚C
Note 1: Absolute maximum ratings indicate limits beyond which damage to the device may occur. Operating Range indicates conditions for which the device is
intended to be functional, but does not guarantee specfic performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics.
Note 2: Thermal shutdown will occur if the junction temperature exceeds the maximum junction temperature of the device.
Note 3: Applies for packages soldered directly onto a 3” x 3” PC board with 2oz. copper on 4 layers in still air.
LM2831
www.national.com5
Typical Performance Characteristics All curves taken at VIN = 5.0V with configuration in typical ap-
plication circuit shown in Application Information section of this datasheet. T
J
= 25˚C, unless otherwise specified.
ηvs Load "X" Vin = 5V, Vo = 1.8V & 3.3V ηvs Load - "Y" Vin = 5V, Vo = 3.3V & 1.8V
20174839 20174886
ηvs Load "Z" Vin = 5V, Vo = 3.3V & 1.8V ηvs Load "X, Y and Z" Vin = 3.3V, Vo = 1.8V
20174842 20174885
Load Regulation
Vin = 3.3V, Vo = 1.8V (All Options)
Load Regulation
Vin = 5V, Vo = 1.8V (All Options)
20174844 20174845
LM2831
www.national.com 6
Typical Performance Characteristics All curves taken at VIN = 5.0V with configuration in typical
application circuit shown in Application Information section of this datasheet. T
J
= 25˚C, unless otherwise
specified. (Continued)
Load Regulation
Vin = 5V, Vo = 3.3V (All Options) Oscillator Frequency vs Temperature - "X"
20174846 20174824
Oscillator Frequency vs Temperature - "Y" Oscillator Frequency vs Temperature - "Z"
20174825 20174836
Current Limit vs Temperature
Vin = 3.3V RDSON vs Temperature (LLP-6 Package)
20174823 20174883
LM2831
www.national.com7
Typical Performance Characteristics All curves taken at VIN = 5.0V with configuration in typical
application circuit shown in Application Information section of this datasheet. T
J
= 25˚C, unless otherwise
specified. (Continued)
RDSON vs Temperature (SOT23-5 Package) LM2831X I
Q
(Quiescent Current)
20174884 20174828
LM2831Y I
Q
(Quiescent Current) LM2831Z I
Q
(Quiescent Current)
20174829 20174837
LM2831
www.national.com 8
Typical Performance Characteristics All curves taken at VIN = 5.0V with configuration in typical
application circuit shown in Application Information section of this datasheet. T
J
= 25˚C, unless otherwise
specified. (Continued)
Line Regulation
Vo = 1.8V, Io = 500mA V
FB
vs Temperature
20174853 20174827
Gain vs Frequency
(Vin = 5V, Vo = 1.2V @1A)
Phase Plot vs Frequency
(Vin = 5V, Vo = 1.2V @1A)
20174856 20174857
LM2831
www.national.com9
Simplified Block Diagram
20174804
FIGURE 1.
LM2831
www.national.com 10
Applications Information
THEORY OF OPERATION
The LM2831 is a constant frequency PWM buck regulator IC
that delivers a 1.5A load current. The regulator has a preset
switching frequency of 550kHz, 1.6MHz, or 3.0MHz. This
high frequency allows the LM2831 to operate with small
surface mount capacitors and inductors, resulting in a
DC/DC converter that requires a minimum amount of board
space. The LM2831 is internally compensated, so it is simple
to use and requires few external components. The LM2831
uses current-mode control to regulate the output voltage.
The following operating description of the LM2831 will refer
to the Simplified Block Diagram (Figure 1) and to the wave-
forms in Figure 2. The LM2831 supplies a regulated output
voltage by switching the internal PMOS control switch at
constant frequency and variable duty cycle. A switching
cycle begins at the falling edge of the reset pulse generated
by the internal oscillator. When this pulse goes low, the
output control logic turns on the internal PMOS control
switch. During this on-time, the SW pin voltage (V
SW
) swings
up to approximately V
IN
, and the inductor current (I
L
) in-
creases with a linear slope. I
L
is measured by the current
sense amplifier, which generates an output proportional to
the switch current. The sense signal is summed with the
regulator’s corrective ramp and compared to the error am-
plifier’s output, which is proportional to the difference be-
tween the feedback voltage and V
REF
. When the PWM
comparator output goes high, the output switch turns off until
the next switching cycle begins. During the switch off-time,
inductor current discharges through the Schottky catch di-
ode, which forces the SW pin to swing below ground by the
forward voltage (V
D
) of the Schottky catch diode. The regu-
lator loop adjusts the duty cycle (D) to maintain a constant
output voltage.
SOFT-START
This function forces V
OUT
to increase at a controlled rate
during start up. During soft-start, the error amplifier’s refer-
ence voltage ramps from 0V to its nominal value of 0.6V in
approximately 600 µs. This forces the regulator output to
ramp up in a controlled fashion, which helps reduce inrush
current.
OUTPUT OVERVOLTAGE PROTECTION
The over-voltage comparator compares the FB pin voltage
to a voltage that is 15% higher than the internal reference
V
REF
. Once the FB pin voltage goes 15% above the internal
reference, the internal PMOS control switch is turned off,
which allows the output voltage to decrease toward regula-
tion.
UNDERVOLTAGE LOCKOUT
Under-voltage lockout (UVLO) prevents the LM2831 from
operating until the input voltage exceeds 2.73V (typ). The
UVLO threshold has approximately 430 mV of hysteresis, so
the part will operate until V
IN
drops below 2.3V (typ). Hys-
teresis prevents the part from turning off during power up if
V
IN
is non-monotonic.
CURRENT LIMIT
The LM2831 uses cycle-by-cycle current limiting to protect
the output switch. During each switching cycle, a current limit
comparator detects if the output switch current exceeds 2.5A
(typ), and turns off the switch until the next switching cycle
begins.
THERMAL SHUTDOWN
Thermal shutdown limits total power dissipation by turning
off the output switch when the IC junction temperature ex-
ceeds 165˚C. After thermal shutdown occurs, the output
switch doesn’t turn on until the junction temperature drops to
approximately 150˚C.
Design Guide
INDUCTOR SELECTION
The Duty Cycle (D) can be approximated quickly using the
ratio of output voltage (V
O
) to input voltage (V
IN
):
The catch diode (D1) forward voltage drop and the voltage
drop across the internal PMOS must be included to calculate
a more accurate duty cycle. Calculate D by using the follow-
ing formula:
V
SW
can be approximated by:
V
SW
=I
OUT
xR
DSON
The diode forward drop (V
D
) can range from 0.3V to 0.7V
depending on the quality of the diode. The lower the V
D
, the
higher the operating efficiency of the converter. The inductor
value determines the output ripple current. Lower inductor
values decrease the size of the inductor, but increase the
output ripple current. An increase in the inductor value will
decrease the output ripple current.
One must ensure that the minimum current limit (1.8A) is not
exceeded, so the peak current in the inductor must be
calculated. The peak current (I
LPK
) in the inductor is calcu-
lated by:
I
LPK
=I
OUT
+i
L
20174866
FIGURE 2. Typical Waveforms
LM2831
www.national.com11
Design Guide (Continued)
In general,
i
L
=0.1x(I
OUT
)0.2x(I
OUT
)
If i
L
= 20% of 1.50A, the peak current in the inductor will be
1.8A. The minimum guaranteed current limit over all operat-
ing conditions is 1.8A. One can either reduce i
L
, or make
the engineering judgment that zero margin will be safe
enough. The typical current limit is 2.5A.
The LM2831 operates at frequencies allowing the use of
ceramic output capacitors without compromising transient
response. Ceramic capacitors allow higher inductor ripple
without significantly increasing output ripple. See the output
capacitor section for more details on calculating output volt-
age ripple. Now that the ripple current is determined, the
inductance is calculated by:
Where
When selecting an inductor, make sure that it is capable of
supporting the peak output current without saturating. Induc-
tor saturation will result in a sudden reduction in inductance
and prevent the regulator from operating correctly. Because
of the speed of the internal current limit, the peak current of
the inductor need only be specified for the required maxi-
mum output current. For example, if the designed maximum
output current is 1.0A and the peak current is 1.25A, then the
inductor should be specified with a saturation current limit of
>1.25A. There is no need to specify the saturation or peak
current of the inductor at the 2.5A typical switch current limit.
The difference in inductor size is a factor of 5. Because of the
operating frequency of the LM2831, ferrite based inductors
are preferred to minimize core losses. This presents little
restriction since the variety of ferrite-based inductors is
huge. Lastly, inductors with lower series resistance (R
DCR
)
will provide better operating efficiency. For recommended
inductors see Example Circuits.
INPUT CAPACITOR
An input capacitor is necessary to ensure that V
IN
does not
drop excessively during switching transients. The primary
specifications of the input capacitor are capacitance, volt-
age, RMS current rating, and ESL (Equivalent Series Induc-
tance). The recommended input capacitance is 22 µF.The
input voltage rating is specifically stated by the capacitor
manufacturer. Make sure to check any recommended derat-
ings and also verify if there is any significant change in
capacitance at the operating input voltage and the operating
temperature. The input capacitor maximum RMS input cur-
rent rating (I
RMS-IN
) must be greater than:
Neglecting inductor ripple simplifies the above equation to:
It can be shown from the above equation that maximum
RMS capacitor current occurs when D = 0.5. Always calcu-
late the RMS at the point where the duty cycle D is closest to
0.5. The ESL of an input capacitor is usually determined by
the effective cross sectional area of the current path. A large
leaded capacitor will have high ESL and a 0805 ceramic chip
capacitor will have very low ESL. At the operating frequen-
cies of the LM2831, leaded capacitors may have an ESL so
large that the resulting impedance (2πfL) will be higher than
that required to provide stable operation. As a result, surface
mount capacitors are strongly recommended.
Sanyo POSCAP, Tantalum or Niobium, Panasonic SP, and
multilayer ceramic capacitors (MLCC) are all good choices
for both input and output capacitors and have very low ESL.
For MLCCs it is recommended to use X7R or X5R type
capacitors due to their tolerance and temperature character-
istics. Consult capacitor manufacturer datasheets to see
how rated capacitance varies over operating conditions.
OUTPUT CAPACITOR
The output capacitor is selected based upon the desired
output ripple and transient response. The initial current of a
load transient is provided mainly by the output capacitor. The
output ripple of the converter is:
When using MLCCs, the ESR is typically so low that the
capacitive ripple may dominate. When this occurs, the out-
put ripple will be approximately sinusoidal and 90˚ phase
shifted from the switching action. Given the availability and
quality of MLCCs and the expected output voltage of designs
using the LM2831, there is really no need to review any other
capacitor technologies. Another benefit of ceramic capaci-
tors is their ability to bypass high frequency noise. A certain
amount of switching edge noise will couple through parasitic
capacitances in the inductor to the output. A ceramic capaci-
tor will bypass this noise while a tantalum will not. Since the
output capacitor is one of the two external components that
control the stability of the regulator control loop, most appli-
cations will require a minimum of 22 µF of output capaci-
tance. Capacitance often, but not always, can be increased
20174805
FIGURE 3. Inductor Current
LM2831
www.national.com 12
Design Guide (Continued)
significantly with little detriment to the regulator stability. Like
the input capacitor, recommended multilayer ceramic ca-
pacitors are X7R or X5R types.
CATCH DIODE
The catch diode (D1) conducts during the switch off-time. A
Schottky diode is recommended for its fast switching times
and low forward voltage drop. The catch diode should be
chosen so that its current rating is greater than:
I
D1
=I
OUT
x (1-D)
The reverse breakdown rating of the diode must be at least
the maximum input voltage plus appropriate margin. To im-
prove efficiency, choose a Schottky diode with a low forward
voltage drop.
OUTPUT VOLTAGE
The output voltage is set using the following equation where
R2 is connected between the FB pin and GND, and R1 is
connected between V
O
and the FB pin. A good value for R2
is 10k. When designing a unity gain converter (Vo = 0.6V),
R1 should be between 0and 100, and R2 should be
equal or greater than 10k.
V
REF
= 0.60V
PCB LAYOUT CONSIDERATIONS
When planning layout there are a few things to consider
when trying to achieve a clean, regulated output. The most
important consideration is the close coupling of the GND
connections of the input capacitor and the catch diode D1.
These ground ends should be close to one another and be
connected to the GND plane with at least two through-holes.
Place these components as close to the IC as possible. Next
in importance is the location of the GND connection of the
output capacitor, which should be near the GND connections
of CIN and D1. There should be a continuous ground plane
on the bottom layer of a two-layer board except under the
switching node island. The FB pin is a high impedance node
and care should be taken to make the FB trace short to avoid
noise pickup and inaccurate regulation. The feedback resis-
tors should be placed as close as possible to the IC, with the
GND of R1 placed as close as possible to the GND of the IC.
The V
OUT
trace to R2 should be routed away from the
inductor and any other traces that are switching. High AC
currents flow through the V
IN
, SW and V
OUT
traces, so they
should be as short and wide as possible. However, making
the traces wide increases radiated noise, so the designer
must make this trade-off. Radiated noise can be decreased
by choosing a shielded inductor. The remaining components
should also be placed as close as possible to the IC. Please
see Application Note AN-1229 for further considerations and
the LM2831 demo board as an example of a four-layer
layout.
LM2831
www.national.com13
Calculating Efficiency, and
Junction Temperature
The complete LM2831 DC/DC converter efficiency can be
calculated in the following manner.
Or
Calculations for determining the most significant power
losses are shown below. Other losses totaling less than 2%
are not discussed.
Power loss (P
LOSS
) is the sum of two basic types of losses in
the converter: switching and conduction. Conduction losses
usually dominate at higher output loads, whereas switching
losses remain relatively fixed and dominate at lower output
loads. The first step in determining the losses is to calculate
the duty cycle (D):
V
SW
is the voltage drop across the internal PFET when it is
on, and is equal to:
V
SW
=I
OUT
xR
DSON
V
D
is the forward voltage drop across the Schottky catch
diode. It can be obtained from the diode manufactures Elec-
trical Characteristics section. If the voltage drop across the
inductor (V
DCR
) is accounted for, the equation becomes:
The conduction losses in the free-wheeling Schottky diode
are calculated as follows:
P
DIODE
=V
D
xI
OUT
x (1-D)
Often this is the single most significant power loss in the
circuit. Care should be taken to choose a Schottky diode that
has a low forward voltage drop.
Another significant external power loss is the conduction
loss in the output inductor. The equation can be simplified to:
P
IND
=I
OUT2
xR
DCR
The LM2831 conduction loss is mainly associated with the
internal PFET:
If the inductor ripple current is fairly small, the conduction
losses can be simplified to:
P
COND
=I
OUT2
xR
DSON
xD
Switching losses are also associated with the internal PFET.
They occur during the switch on and off transition periods,
where voltages and currents overlap resulting in power loss.
The simplest means to determine this loss is to empirically
measuring the rise and fall times (10% to 90%) of the switch
at the switch node.
Switching Power Loss is calculated as follows:
P
SWR
= 1/2(V
IN
xI
OUT
xF
SW
xT
RISE
)
P
SWF
= 1/2(V
IN
xI
OUT
xF
SW
xT
FALL
)
P
SW
=P
SWR
+P
SWF
Another loss is the power required for operation of the inter-
nal circuitry:
P
Q
=I
Q
xV
IN
I
Q
is the quiescent operating current, and is typically around
2.5mA for the 0.55MHz frequency option.
Typical Application power losses are:
Power Loss Tabulation
V
IN
5.0V
V
OUT
3.3V P
OUT
4.125W
I
OUT
1.25A
V
D
0.45V P
DIODE
188mW
F
SW
550kHz
I
Q
2.5mA P
Q
12.5mW
T
RISE
4nS P
SWR
7mW
T
FALL
4nS P
SWF
7mW
R
DS(ON)
150mP
COND
156mW
IND
DCR
70mP
IND
110mW
D 0.667 P
LOSS
481mW
η88% P
INTERNAL
183mW
ΣP
COND
+P
SW
+P
DIODE
+P
IND
+P
Q
=P
LOSS
ΣP
COND
+P
SWF
+P
SWR
+P
Q
=P
INTERNAL
P
INTERNAL
= 183mW
Thermal Definitions
T
J
= Chip junction temperature
T
A
= Ambient temperature
R
θJC
= Thermal resistance from chip junction to device case
R
θJA
= Thermal resistance from chip junction to ambient air
Heat in the LM2831 due to internal power dissipation is
removed through conduction and/or convection.
Conduction: Heat transfer occurs through cross sectional
areas of material. Depending on the material, the transfer of
heat can be considered to have poor to good thermal con-
ductivity properties (insulator vs. conductor).
Heat Transfer goes as:
Silicon package lead frame PCB
Convection: Heat transfer is by means of airflow. This could
be from a fan or natural convection. Natural convection
occurs when air currents rise from the hot device to cooler
air.
Thermal impedance is defined as:
LM2831
www.national.com 14
Thermal Definitions (Continued)
Thermal impedance from the silicon junction to the ambient
air is defined as:
The PCB size, weight of copper used to route traces and
ground plane, and number of layers within the PCB can
greatly effect R
θJA
. The type and number of thermal vias can
also make a large difference in the thermal impedance.
Thermal vias are necessary in most applications. They con-
duct heat from the surface of the PCB to the ground plane.
Four to six thermal vias should be placed under the exposed
pad to the ground plane if the LLP package is used.
Thermal impedance also depends on the thermal properties
of the application operating conditions (Vin, Vo, Io etc), and
the surrounding circuitry.
Silicon Junction Temperature Determination Method 1:
To accurately measure the silicon temperature for a given
application, two methods can be used. The first method
requires the user to know the thermal impedance of the
silicon junction to top case temperature.
Some clarification needs to be made before we go any
further.
R
θJC
is the thermal impedance from all six sides of an IC
package to silicon junction.
R
ΦJC
is the thermal impedance from top case to the silicon
junction.
In this data sheet we will use R
ΦJC
so that it allows the user
to measure top case temperature with a small thermocouple
attached to the top case.
R
ΦJC
is approximately 30˚C/Watt for the 6-pin LLP package
with the exposed pad. Knowing the internal dissipation from
the efficiency calculation given previously, and the case
temperature, which can be empirically measured on the
bench we have:
Therefore:
T
j
=(R
ΦJC
xP
LOSS
)+T
C
From the previous example:
T
j
=(R
ΦJC
xP
INTERNAL
)+T
C
T
j
= 30˚C/W x 0.189W + T
C
The second method can give a very accurate silicon junction
temperature.
The first step is to determine R
θJA
of the application. The
LM2831 has over-temperature protection circuitry. When the
silicon temperature reaches 165˚C, the device stops switch-
ing. The protection circuitry has a hysteresis of about 15˚C.
Once the silicon temperature has decreased to approxi-
mately 150˚C, the device will start to switch again. Knowing
this, the R
θJA
for any application can be characterized during
the early stages of the design one may calculate the R
θJA
by
placing the PCB circuit into a thermal chamber. Raise the
ambient temperature in the given working application until
the circuit enters thermal shutdown. If the SW-pin is moni-
tored, it will be obvious when the internal PFET stops switch-
ing, indicating a junction temperature of 165˚C. Knowing the
internal power dissipation from the above methods, the junc-
tion temperature, and the ambient temperature R
θJA
can be
determined.
Once this is determined, the maximum ambient temperature
allowed for a desired junction temperature can be found.
An example of calculating R
θJA
for an application using the
National Semiconductor LM2831 LLP demonstration board
is shown below.
The four layer PCB is constructed using FR4 with
1
2
oz
copper traces. The copper ground plane is on the bottom
layer. The ground plane is accessed by two vias. The board
measures 3.0cm x 3.0cm. It was placed in an oven with no
forced airflow. The ambient temperature was raised to
144˚C, and at that temperature, the device went into thermal
shutdown.
From the previous example:
P
INTERNAL
= 189mW
If the junction temperature was to be kept below 125˚C, then
the ambient temperature could not go above 109˚C
T
j
-(R
θJA
xP
LOSS
)=T
A
125˚C - (111˚C/W x 189mW) = 104˚C
LLP Package
For certain high power applications, the PCB land may be
modified to a "dog bone" shape (see Figure 6). By increasing
the size of ground plane, and adding thermal vias, the R
θJA
for the application can be reduced.
20174868
FIGURE 4. Internal LLP Connection
LM2831
www.national.com15
LLP Package (Continued)
20174806
FIGURE 5. 6-Lead LLP PCB Dog Bone Layout
LM2831
www.national.com 16
LM2831X Design Example 1
Bill of Materials
Part ID Part Value Manufacturer Part Number
U1 1.5A Buck Regulator NSC LM2831X
C1, Input Cap 22µF, 6.3V, X5R TDK C3216X5ROJ226M
C2, Output Cap 2x22µF, 6.3V, X5R TDK C3216X5ROJ226M
D1, Catch Diode 0.3V
f
Schottky 1.5A, 30V
R
TOSHIBA CRS08
L1 3.3µH, 2.2A TDK VLCF5020T-3R3N2R0-1
R2 15.0k, 1% Vishay CRCW08051502F
R1 15.0k, 1% Vishay CRCW08051502F
R3 100k, 1% Vishay CRCW08051003F
20174807
FIGURE 6. LM2831X (1.6MHz): Vin = 5V, Vo = 1.2V @1.5A
LM2831
www.national.com17
LM2831X Design Example 2
Bill of Materials
Part ID Part Value Manufacturer Part Number
U1 1.5A Buck Regulator NSC LM2831X
C1, Input Cap 22µF, 6.3V, X5R TDK C3216X5ROJ226M
C2, Output Cap 2x22µF, 6.3V, X5R TDK C3216X5ROJ226M
D1, Catch Diode 0.3V
f
Schottky 1.5A, 30V
R
TOSHIBA CRS08
L1 3.3µH, 2.2A TDK VLCF5020T- 3R3N2R0-1
R2 10.0k, 1% Vishay CRCW08051000F
R1 0
R3 100k, 1% Vishay CRCW08051003F
20174860
FIGURE 7. LM2831X (1.6MHz): Vin = 5V, Vo = 0.6V @1.5A
LM2831
www.national.com 18
LM2831X Design Example 3
Bill of Materials
Part ID Part Value Manufacturer Part Number
U1 1.5A Buck Regulator NSC LM2831X
C1, Input Cap 22µF, 6.3V, X5R TDK C3216X5ROJ226M
C2, Output Cap 2x22µF, 6.3V, X5R TDK C3216X5ROJ226M
D1, Catch Diode 0.3V
f
Schottky 1.5A, 30V
R
TOSHIBA CRS08
L1 2.7µH 2.3A TDK VLCF5020T-2R7N2R2-1
R2 10.0k, 1% Vishay CRCW08051002F
R1 45.3k, 1% Vishay CRCW08054532F
R3 100k, 1% Vishay CRCW08051003F
20174808
FIGURE 8. LM2831X (1.6MHz): Vin = 5V, Vo = 3.3V @1.5A
LM2831
www.national.com19
LM2831Y Design Example 4
Bill of Materials
Part ID Part Value Manufacturer Part Number
U1 1.5A Buck Regulator NSC LM2831Y
C1, Input Cap 22µF, 6.3V, X5R TDK C3216X5ROJ226M
C2, Output Cap 2x22µF, 6.3V, X5R TDK C3216X5ROJ226M
D1, Catch Diode 0.3V
f
Schottky 1.5A, 30V
R
TOSHIBA CRS08
L1 4.7µH 2.1A TDK SLF7045T-4R7M2R0-PF
R1 10.0k, 1% Vishay CRCW08051002F
R2 10.0k, 1% Vishay CRCW08051002F
20174808
FIGURE 9. LM2831Y (550kHz): Vin = 5V, Vout = 3.3V @1.5A
LM2831
www.national.com 20
LM2831Y Design Example 5
Bill of Materials
Part ID Part Value Manufacturer Part Number
U1 1.5A Buck Regulator NSC LM2831Y
C1, Input Cap 22µF, 6.3V, X5R TDK C3216X5ROJ226M
C2, Output Cap 2x22µF, 6.3V, X5R TDK C3216X5ROJ226M
D1, Catch Diode 0.3V
f
Schottky 1.5A, 30V
R
TOSHIBA CRS08
L1 6.8µH 1.8A TDK SLF7045T-6R8M1R7
R1 10.0k, 1% Vishay CRCW08051002F
R2 10.0k, 1% Vishay CRCW08051002F
20174807
FIGURE 10. LM2831Y (550kHz): Vin = 5V, Vout = 1.2V @1.5A
LM2831
www.national.com21
LM2831Z Design Example 6
Bill of Materials
Part ID Part Value Manufacturer Part Number
U1 1.5A Buck Regulator NSC LM2831Z
C1, Input Cap 22µF, 6.3V, X5R TDK C3216X5ROJ226M
C2, Output Cap 2x22µF, 6.3V, X5R TDK C3216X5ROJ226M
D1, Catch Diode 0.3V
f
Schottky 1.5A, 30V
R
TOSHIBA CRS08
L1 1.6µH 2.0A TDK VLCF4018T-1R6N1R7-2
R2 10.0k, 1% Vishay CRCW08051002F
R1 45.3k, 1% Vishay CRCW08054532F
R3 100k, 1% Vishay CRCW08051003F
20174808
FIGURE 11. LM2831Z (3MHz): Vin = 5V, Vo = 3.3V @1.5A
LM2831
www.national.com 22
LM2831Z Design Example 7
Bill of Materials
Part ID Part Value Manufacturer Part Number
U1 1.5A Buck Regulator NSC LM2831Z
C1, Input Cap 22µF, 6.3V, X5R TDK C3216X5ROJ226M
C2, Output Cap 2x22µF, 6.3V, X5R TDK C3216X5ROJ226M
D1, Catch Diode 0.3V
f
Schottky 1.5A, 30V
R
TOSHIBA CRS08
L1 1.6µH, 2.0A TDK VLCF4018T- 1R6N1R7-2
R2 10.0k, 1% Vishay CRCW08051002F
R1 10.0k, 1% Vishay CRCW08051002F
R3 100k, 1% Vishay CRCW08051003F
20174807
FIGURE 12. LM2831Z (3MHz): Vin = 5V, Vo = 1.2V @1.5A
LM2831
www.national.com23
LM2831X Dual Converters with Delayed Enabled Design Example 8
Bill of Materials
Part ID Part Value Manufacturer Part Number
U1, U2 1.5A Buck Regulator NSC LM2831X
U3 Power on Reset NSC LP3470M5X-3.08
C1, C3 Input Cap 22µF, 6.3V, X5R TDK C3216X5ROJ226M
C2, C4 Output Cap 2x22µF, 6.3V, X5R TDK C3216X5ROJ226M
C7 Trr delay capacitor TDK
D1, D2 Catch Diode 0.3V
f
Schottky 1.5A, 30V
R
TOSHIBA CRS08
L1, L2 3.3µH, 2.2A TDK VLCF5020T-3R3N2R0-1
R2, R4, R5 10.0k, 1% Vishay CRCW08051002F
R1, R6 45.3k, 1% Vishay CRCW08054532F
R3 100k, 1% Vishay CRCW08051003F
20174862
FIGURE 13. LM2831X (1.6MHz): Vin = 5V, Vo = 1.2V @1.5A & 3.3V @1.5A
LM2831
www.national.com 24
LM2831X Buck Converter & Voltage Double Circuit with LDO Follower
Design Example 9
Bill of Materials
Part ID Part Value Manufacturer Part Number
U1 1.5A Buck Regulator NSC LM2831X
U2 200mA LDO NSC LP2986-5.0
C1, Input Cap 22µF, 6.3V, X5R TDK C3216X5ROJ226M
C2, Output Cap 22µF, 6.3V, X5R TDK C3216X5ROJ226M
C3 C6 2.2µF, 6.3V, X5R TDK C1608X5R0J225M
D1, Catch Diode 0.3V
f
Schottky 1.5A, 30V
R
TOSHIBA CRS08
D2 0.4V
f
Schottky 20V
R
, 500mA ON Semi MBR0520
L2 10µH, 800mA CoilCraft ME3220-103
L1 3.3µH, 2.2A TDK VLCF5020T-3R3N2R0-1
R2 45.3k, 1% Vishay CRCW08054532F
R1 10.0k, 1% Vishay CRCW08051002F
20174863
FIGURE 14. LM2831X (1.6MHz): Vin = 5V, Vo = 3.3V @1.5A & LP2986-5.0 @150mA
LM2831
www.national.com25
Physical Dimensions inches (millimeters) unless otherwise noted
5-Lead SOT-23 Package
NS Package Number MF05A
6-Lead LLP Package
NS Package Number SDE06A
LM2831
www.national.com 26
Notes
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves
the right at any time without notice to change said circuitry and specifications.
For the most current product information visit us at www.national.com.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS
WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
(b) support or sustain life, and whose failure to perform when
properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result
in a significant injury to the user.
2. A critical component is any component of a life support
device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor follows the provisions of the Product Stewardship Guide for Customers (CSP-9-111C2) and Banned Substances
and Materials of Interest Specification (CSP-9-111S2) for regulatory environmental compliance. Details may be found at:
www.national.com/quality/green.
Lead free products are RoHS compliant.
National Semiconductor
Americas Customer
Support Center
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
National Semiconductor
Asia Pacific Customer
Support Center
Email: ap.support@nsc.com
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560
www.national.com
LM2831 High Frequency 1.5A Load - Step-Down DC-DC Regulator
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TIs terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TIs standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Audio www.ti.com/audio Communications and Telecom www.ti.com/communications
Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers
Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps
DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy
DSP dsp.ti.com Industrial www.ti.com/industrial
Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical
Interface interface.ti.com Security www.ti.com/security
Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright ©2011, Texas Instruments Incorporated