LEE-128G032B
www.vishay.com Vishay Dale
Revision: 07-Dec-12 1Document Number: 37088
For technical questions, contact: displays@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
LED Display Modules
128 x 32 Graphics Display with Drive Electronics and + 5 V HC CMOS Level Video Interface
Red LED Modules, Normal Brightness, Single Board Construction, RoHS-Compliant
The LEE-128G032B is an LED replacement for the popular
APD-128G032 plasma display module. It is designed to
offer high brightness and superior viewing characteristics in
a slim package. This display is ideal for low to medium level
information content and is ideal for applications such as
arcade games, process control, POS terminals, medical
equipment, message centers and ATM machines.
The LEE-128G032B LED display offers high contrast, wide
viewing angle, and long distance readability. It emits a bright
red color which catches the attention of the viewer, but is yet
comfortable to the eye.
The LEE-128G032B LED display has a video type interface
and is driven in a standard row/column refresh method.
Pixel data is clocked for a row, and rows are scanned
sequentially. Signals are presented for serial data, dot clock,
column latch, row data, row clock and display enable. The
serial data is entered with the dot clock up to frequencies as
high as 8 MHz. After a row of 128 pixels is clocked in, the
column latch signal is toggled and the data is latched. At the
time the data is latched, the display is briefly disabled using
the display enable signal, then the row pointer is advanced
with the row clock signal. Once each frame the row data
must be asserted to synchronize the column serial data with
the beginning row. The recommended scanning frequency
is approximately 70 Hz, but may be as high as 200 Hz.
Note
• Recommended operating voltages, all maximums are absolute
maximum
FEATURES
• LED replacement for the popular APD-128G032
plasma display module
• + 5 V HC CMOS level video interface
• Large characters
• Highly visible for long distance viewing
• > 30:1 contrast ratio
• Bright red color
• Slim profile
• Reduced power and brightness version
• Material categorization: For definitions of compliance
please see www.vishay.com/doc?99912
ELECTRICAL SPECIFICATIONS
Voltage(s) Required: + 5 VDC (VCC)
Power Required (Fully Lit): Typ. = 5.5 W, max. = 6.5 W
OPTICAL SPECIFICATIONS
Viewing Area: 12.75" [323.8 mm] W x 3.15" [80.01 mm] L
Character Size (5 x 7):
0.65" [16.51 mm] H x 0.45" [11.43 mm] W
Pixel Size: 0.063" [1.6 mm] H x 0.031" [0.8 mm] W
Pixel Pitch: 0.100" [2.54 mm]
Luminance: 100 ft-L minimum
Color: Bright red
Viewing Angle: > 150°
ENVIRONMENTAL SPECIFICATIONS
Operating Temperature: - 40 °C to + 85 °C
Storage Temperature: - 40 °C to + 85 °C
Relative Operating Humidity: To 95 % non-condensing
Mechanical Shock: 30 G
Vibration: 3 G
Operating Altitude: 10 000 ft
STANDARD ELECTRICAL SPECIFICATIONS
DESCRIPTION SYMBOL MIN. TYP. MAX. UNITS
Logic and LED
Drive Voltage VCC + 4.5 + 5.0 + 5.5 VDC
Logic and LED
Drive Current
(Fully Lit)
ICC -1.11.3A
DC
Logic 1 Input Vih 0.7 VCC --V
DC
Logic 0 Input Vil - - 0.3 VCC VDC
DIMENSIONS in inches [millimeters]
0.250
Max.
0.062
0.75 Max.
Component Height
7.25
14.80
0.150
7.25
4.625
4.925
0.150
3.15
Viweing
Area
0.889
12.68 Viewing Area
Pin 1 of J1 Pin 1 of J2
0.150 Mounting Holes (6 x)
1.057
LEE-128G032B
www.vishay.com Vishay Dale
Revision: 07-Dec-12 2Document Number: 37088
For technical questions, contact: displays@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
INTERFACE SIGNAL DESCRIPTION
Dot clock - This signal enters the serial data on each low to
high transition. A total of 128 dot clock transitions must be
present for each line of column/anode data.
Serial data - This signal presents the pixel data in positive
logic format. A logic one represents a lit pixel and a logic
zero represents an extinguished pixel. Data is entered from
right to left. The first pixel data entered will represent the left
most pixel in the row.
Column latch - This signal latches the pixel data into the
driver outputs. When the column latch signal goes to logic
one the data entered previously will fall through to the driver
outputs. When the signal returns to a logic zero the data is
latched and the shift register is now ready to accept the next
row of data. Must be held low while entering new serial data.
Display enable - This signal enables the output drivers.
Using a duty cycle control, this signal may also be used for
intensity control. The display enable must be at logic zero
before the column latch signal transitions. To avoid display
blurring, the row clock signal should also transition while
display enable is a logic zero.
Row data - This signal is the first line marker for the scan.
This input should be held high to correspond to the first row
of pixel data.
Row clock - This signal clocks row data on the falling edge.
The row clock signal is repetitive and must be present for
proper scanning of the display module.
The LEE-128G032B has an unique input protection circuit
that assures the column drivers stay blanked on power up.
The protection circuit unblanks the column drivers when the
row clock signal begins (i.e the display begins scanning).
PIN DESCRIPTION
J2 - POWER CONNECTOR
Molex 26-48-1045 or equivalent.
Mates with Tyco AMP 3-640428-8, or Molex 09-50-3041
housing with 08-50-0106 socket crimp terminals or equivalent.
PIN SIGNAL DESCRIPTION
1V
CC Logic and LED drive supply
2V
CC Logic and LED drive supply
3 GND Ground
4 GND Ground
J1 - DATA CONNECTOR
FCI 75869-102LF or equivalent.
Mates with Tyco AMP 1658621-2 or equivalent
PIN DESCRIPTION PIN DESCRIPTION
1 Display enable 2 Ground
3 Row data 4 Ground
5 Row clock 6 Ground
7 Column latch 8 Ground
9 Dot clock 10 Ground
11 Serial data 12 Ground
13 No connection 14 Ground
LOGIC AND DATA TIMING
PARAMETER MIN. TYP. MAX. UNITS
t1100 - - ns
t25--μs
t31--μs
t4- 70 200 Hz
t525 - - ns
t675 - - ns
t775 - - ns
ORDERING INFORMATION
DESCRIPTION PART NUMBER
Display, Driver Electronics and
+ 5 V HC CMOS Interface LED-128G032B
J1 Data Connector Kit
(2 pcs. recommended) 280105-08
J2 Power Connector Kit 280108-16
Row Clock
Column Latch
Display Enable
Row Data
t4
Display Enable
2
1
0303101
Serial Data 210 126 127
1st bit of row will appear in left most column
t2
Row Clock
230310
110
t3
t1
t5
Dot Clock
Positive edge x 128t6t7
Legal Disclaimer Notice
www.vishay.com Vishay
Revision: 08-Feb-17 1Document Number: 91000
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular application.
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for
such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
