Revised November 1999 74AC153 * 74ACT153 Dual 4-Input Multiplexer General Description Features The AC/ACT153 is a high-speed dual 4-input multiplexer with common select inputs and individual enable inputs for each section. It can select two lines of data from four sources. The two buffered outputs present data in the true (non-inverted) form. In addition to multiplexer operation, the AC/ACT153 can act as a function generator and generate any two functions of three variables. ICC reduced by 50% Outputs source/sink 24 mA ACT153 has TTL-compatible inputs Ordering Code: Order Number 74AC153SC 74AC153SJ 74AC153MTC Package Number Package Description M16A 16-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow Body M16D 16-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide MTC16 74AC153PC 74ACT153SC 74ACT153MTC 16-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide N16E 16-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300" Wide M16A 16-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow Body MTC16 16-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide Device also available in Tape and Reel. Specify by appending suffix letter "X" to the ordering code. Logic Symbols Connection Diagram IEEE/IEC Pin Descriptions Pin Names Description I0a-I3a Side A Data Inputs I0b-I3b Side B Data Inputs S0 , S1 Common Select Inputs Ea Side A Enable Input Eb Side B Enable Input Za Side A Output Zb Side B Output FACT is a trademark of Fairchild Semiconductor Corporation. (c) 1999 Fairchild Semiconductor Corporation DS009928 www.fairchildsemi.com 74AC153 * 74ACT153 Dual 4-Input Multiplexer November 1988 74AC153 * 74ACT153 Functional Description Truth Table The AC/ACT153 is a dual 4-input multiplexer. It can select two bits of data from up to four sources under the control of the common Select inputs (S0, S1). The two 4-input multiplexer circuits have individual active-LOW Enables (Ea, Eb) which can be used to strobe the outputs independently. When the Enables (Ea, Eb) are HIGH, the corresponding outputs Za, Zb) are forced LOW. The AC/ACT153 is the logic implementation of a 2-pole, 4-position switch, where the position of the switch is determined by the logic levels supplied to the Select inputs. The logic equations for the outputs are shown below. Select Inputs (a or b) Inputs Za = Ea * (I0a * S1 * S0 + I1a * S1 * S0 + I2a * S1 * S0 + I3a * S1 * S0) Zb = Eb * (I0b * S1 * S0 + I1b * S1 * S0 + I2b * S1 * S0 + I3b * S1 * S0) Output S0 S1 E I0 I1 I2 I3 X X H X X X X L L L L L X X X L L L L H X X X H H L L X L X X L H L L X H X X H L H L X X L X L L H L X X H X H H H L X X X L L H H L X X X H H H = HIGH Voltage Level L = LOW Voltage Level X = Immaterial Logic Diagram Please note that this diagram is provided only for the understanding of logic operations and should not be used to estimate propagation delays. www.fairchildsemi.com 2 Z Supply Voltage (VCC) Recommended Operating Conditions -0.5V to +7.0V DC Input Diode Current (IIK) VI = -0.5V -20 mA VI = VCC + 0.5V +20 mA DC Input Voltage (VI) Supply Voltage (VCC) -0.5V to VCC + 0.5V DC Output Diode Current (IOK) VO = -0.5V -20 mA VO = VCC + 0.5V +20 mA DC Output Voltage (VO) 4.5V to 5.5V 0V to VCC Output Voltage (VO) 0V to VCC -40C to +85C Operating Temperature (TA) Minimum Input Edge Rate (V/t) -0.5V to VCC + 0.5V AC Devices VIN from 30% to 70% of VCC 50 mA VCC @ 3.3V, 4.5V, 5.5V DC VCC or Ground Current 125 mV/ns Minimum Input Edge Rate (V/t) 50 mA per Output Pin (ICC or IGND) Storage Temperature (TSTG) 2.0V to 6.0V ACT Input Voltage (VI) DC Output Source or Sink Current (IO) AC ACT Devices -65C to +150C VIN from 0.8V to 2.0V Junction Temperature (TJ) VCC @ 4.5V, 5.5V PDIP 140C 125 mV/ns Note 1: Absolute maximum ratings are those values beyond which damage to the device may occur. The databook specifications should be met, without exception, to ensure that the system design is reliable over its power supply, temperature, and output/input loading variables. Fairchild does not recommend operation of FACT circuits outside databook specifications. DC Electrical Characteristics for AC Symbol VIH VIL VOH Parameter VCC TA = +25C TA = -40C to +85C (V) Typ Guaranteed Limits Minimum HIGH Level 3.0 1.5 2.1 2.1 Input Voltage 4.5 2.25 3.15 3.15 5.5 2.75 3.85 3.85 Maximum LOW Level 3.0 1.5 0.9 0.9 Input Voltage 4.5 2.25 1.35 1.35 5.5 2.75 1.65 1.65 Minimum HIGH Level 3.0 2.99 2.9 2.9 Output Voltage 4.5 4.49 4.4 4.4 5.5 5.49 5.4 5.4 3.0 2.56 2.46 4.5 3.86 3.76 5.5 4.86 4.76 Units Conditions VOUT = 0.1V V or VCC - 0.1V V or VCC - 0.1V V IOUT = -50 A VOUT = 0.1V VIN = VIL or VIH VOL Maximum LOW Level 3.0 0.002 0.1 0.1 Output Voltage 4.5 0.001 0.1 0.1 5.5 0.001 0.1 0.1 3.0 0.36 0.44 4.5 0.36 0.44 5.5 0.36 0.44 5.5 0.1 IOH = -12 mA V IOH = -24 mA IOH = -24 mA (Note 2) V IOUT = 50 A VIN = VIL or VIH IOL = 12 mA V IOL = 24 mA IOL = 24 mA (Note 2) IIN Maximum Input (Note 4) Leakage Current 1.0 A VI = VCC, GND IOLD Minimum Dynamic 5.5 75 mA VOLD = 1.65V Max 5.5 -75 mA IOHD Output Current (Note 3) ICC Maximum Quiescent (Note 4) Supply Current 5.5 4.0 40.0 A VOHD = 3.85V Min VIN = VCC or GND Note 2: All outputs loaded; thresholds on input associated with output under test. Note 3: Maximum test duration 2.0 ms, one output loaded at a time. Note 4: IIN and ICC @ 3.0V are guaranteed to be less than or equal to the respective limit @ 5.5V VCC. 3 www.fairchildsemi.com 74AC153 * 74ACT153 Absolute Maximum Ratings(Note 1) 74AC153 * 74ACT153 DC Electrical Characteristics for ACT Symbol Parameter TA = +25C VCC TA = -40C to +85C (V) Typ Guaranteed Limits 4.5 1.5 2.0 2.0 VIH Minimum HIGH Level Input Voltage 5.5 1.5 2.0 2.0 VIL Maximum LOW Level 4.5 1.5 0.8 0.8 Input Voltage 5.5 1.5 0.8 0.8 Minimum HIGH Level 4.5 4.49 4.4 4.4 Output Voltage 5.5 5.49 5.4 5.4 VOH Units V V V Conditions VOUT = 0.1V or VCC - 0.1V VOUT = 0.1V or VCC - 0.1V IOUT = -50 A VIN = VIL or VIH VOL 4.5 3.86 3.76 5.5 4.86 4.76 Maximum LOW Level 4.5 0.001 0.1 0.1 Output Voltage 5.5 0.001 0.1 0.1 4.5 0.36 0.44 5.5 0.36 0.44 5.5 0.1 1.0 V IOH = - 24 mA IOH = - 24 mA (Note 5) V IOUT = 50 A VIN = VIL or VIH IIN Maximum Input Leakage Current V IOL = 24 mA IOL = 24 mA (Note 5) A VI = V CC, GND ICCT Maximum 1.5 mA VI = V CC - 2.1V IOLD Minimum Dynamic 5.5 75 mA VOLD = 1.65V Max IOHD Output Current (Note 6) 5.5 -75 mA VOHD = 3.85V Min ICC Maximum Quiescent 40.0 A 5.5 ICC/Input Supply Current 0.6 5.5 4.0 VIN = VCC or GND Note 5: All outputs loaded; thresholds on input associated with output under test. Note 6: Maximum test duration 2.0 ms, one output loaded at a time. AC Electrical Characteristics for AC Symbol tPLH tPHL tPLH tPHL tPLH tPHL Parameter VCC TA = +25C (V) CL = 50 pF TA = -40C to +85C CL = 50 pF (Note 7) Min Typ Max Min Max Propagation Delay 3.3 2.5 9.5 15.0 2.5 17.5 Sn to Zn 5.0 2.0 6.5 11.0 2.0 12.5 Propagation Delay 3.3 3.0 8.5 14.5 2.5 16.5 Sn to Zn 5.0 2.5 6.5 11.0 2.0 12.0 Propagation Delay 3.3 2.5 8.0 13.5 2.0 16.0 E to Zn 5.0 1.5 5.5 9.5 1.5 11.0 Propagation Delay 3.3 2.5 7.0 11.0 2.0 12.5 E to Zn 5.0 2.0 5.0 8.0 1.5 9.0 Propagation Delay 3.3 2.5 7.5 12.5 2.0 14.5 In to Zn 5.0 1.5 5.5 9.0 1.5 10.5 Propagation Delay 3.3 1.5 7.0 11.5 1.5 13.0 In to Zn 5.0 1.5 5.0 8.5 1.5 10.0 Note 7: Voltage Range 3.3 is 3.3V 0 3V Voltage Range 5.0 is 5.0V 0.5V www.fairchildsemi.com 4 Units ns ns ns ns ns ns Symbol tPLH Parameter Propagation Delay Sn to Zn tPHL Propagation Delay Sn to Zn tPLH VCC TA = +25C (V) CL = 50 pF TA = -40C to +85C CL = 50 pF Units (Note 8) Min Typ Max Min Max 5.0 3.0 7.0 11.5 2.0 13.5 ns 5.0 3.0 7.0 11.5 2.5 13.5 ns 5.0 2.0 6.5 10.5 2.0 12.5 ns 5.0 3.0 6.0 9.5 2.5 11.0 ns 5.0 2.5 5.5 9.5 2.0 11.0 ns 5.0 2.0 5.5 9.5 2.0 11.0 ns Propagation Delay En to Zn tPHL Propagation Delay En to Zn tPLH Propagation Delay In to Zn tPHL Propagation Delay In to Zn Note 8: Voltage Range 5.0 is 5.0V 0.5V Capacitance Typ Units CIN Symbol Input Capacitance Parameter 4.5 pF VCC = OPEN CPD Power Dissipation Capacitance 65.0 pF VCC = 5.0V 5 Conditions www.fairchildsemi.com 74AC153 * 74ACT153 AC Electrical Characteristics for ACT 74AC153 * 74ACT153 Physical Dimensions inches (millimeters) unless otherwise noted 16-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow Body Package Number M16A www.fairchildsemi.com 6 74AC153 * 74ACT153 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 16-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide Package Number M16D 7 www.fairchildsemi.com 74AC153 * 74ACT153 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 16-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide Package Number MTC16 www.fairchildsemi.com 8 74AC153 * 74ACT153 Dual 4-Input Multiplexer Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 16-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300" Wide Package Number N16E Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. www.fairchildsemi.com 9 www.fairchildsemi.com