PM4H-A/S/M PM4H-A PM4H-S PM4H-M DIN48 SIZE MULTI-RANGE ANALOG TIMER Analog Timers UL File No.: E122222 CSA File No.: LR39291 Features 48 1.890 62.5 2.461 48 1.890 mm inch Pin type Screw terminal type * 100-240V AC free-voltage input, 48-125V DC type available * Short body -- 62.5mm 2.461 inch (screw terminal type) * Front panel of IP65 type is protected against water-splash and dust * Built-in Screw terminals Screw terminal type is used for easy wiring and reducing additional cost for accessories. * 0 setting instantaneous output operation * Multiple time ranges -- 1 s to 500 h (Max.) * 8 different operation modes: (PM4H-A) * Compliant with UL/CSA, CE and LLOYD Product types Type Operation mode Contact arrangement Time range Protective construction Rated operating voltage 100 to 240V AC 48 to 125V DC IP65 PM4H-A 8 operation modes * Pulse ON-delay * Pulse Flicker * Pulse ON-flicker * Differential ON/OFF-delay (1) (2) * Signal OFF-delay * Pulse One-shot * Pulse One-cycle 24V AC/DC 12V DC Relay Timed-out 2 Form C 100 to 240V AC 48 to 125V DC IP50 24V AC/DC 12V DC 100 to 240V AC 48 to 125V DC IP65 24V AC/DC PM4H-S Power ON-delay Relay Timed-out 2 Form C 12V DC 16 selectable ranges 1s to 500h 100 to 240V AC 48 to 125V DC IP50 24V AC/DC 12V DC 100 to 240V AC 48 to 125V DC IP65 PM4H-M 5 operation modes (With instantaneous contact) * Power ON-delay * Power Flicker * Power ON-flicker * Power One-shot * Power One-cycle 24V AC/DC Relay Timed-out 1 Form C Instantaneous 1 Form C 12V DC 100 to 240V AC 48 to 125V DC IP50 24V AC/DC 12V DC Terminal type Part number 11 pins Screw terminal 11 pins Screw terminal 11 pins Screw terminal 11 pins Screw terminal 11 pins Screw terminal 11 pins Screw terminal 11 pins Screw terminal 11 pins Screw terminal 8 pins Screw terminal 8 pins Screw terminal 8 pins Screw terminal 8 pins Screw terminal 8 pins Screw terminal 8 pins Screw terminal 8 pins Screw terminal 8 pins Screw terminal 8 pins Screw terminal 8 pins Screw terminal 8 pins Screw terminal 8 pins Screw terminal 8 pins Screw terminal 8 pins Screw terminal 8 pins Screw terminal 8 pins Screw terminal PM4HA-H-AC240VW PM4HA-H-AC240VSW PM4HA-H-DC125VW PM4HA-H-DC125VSW PM4HA-H-24VW PM4HA-H-24VSW PM4HA-H-DC12VW PM4HA-H-DC12VSW PM4HA-H-AC240V PM4HA-H-AC240VS PM4HA-H-DC125V PM4HA-H-DC125VS PM4HA-H-24V PM4HA-H-24VS PM4HA-H-DC12V PM4HA-H-DC12VS PM4HS-H-AC240VW PM4HS-H-AC240VSW PM4HS-H-DC125VW PM4HS-H-DC125VSW PM4HS-H-24VW PM4HS-H-24VSW PM4HS-H-DC12VW PM4HS-H-DC12VSW PM4HS-H-AC240V PM4HS-H-AC240VS PM4HS-H-DC125V PM4HS-H-DC125VS PM4HS-H-24V PM4HS-H-24VS PM4HS-H-DC12V PM4HS-H-DC12VS PM4HM-H-AC240VW PM4HM-H-AC240VSW PM4HM-H-DC125VW PM4HM-H-DC125VSW PM4HM-H-24VW PM4HM-H-24VSW PM4HM-H-DC12VW PM4HM-H-DC12VSW PM4HM-H-AC240V PM4HM-H-AC240VS PM4HM-H-DC125V PM4HM-H-DC125VS PM4HM-H-24V PM4HM-H-24VS PM4HM-H-DC12V PM4HM-H-DC12VS If you use this timer under harsh environment, please order above sealed type (IP65 type). IP65 type -- Protection dust and water jet splay on the front face. 09/2009 38 PM4H-A/S/M Time range Time unit sec Scale 1 5 10 Control time range min hrs 10h 1.0h to 10h 0.1s to 1s 0.1 min to 1 min 0.1h to 1h 0.5s to 5s 0.5 min to 5 min 0.5h to 5h 5h to 50h 1.0s to 10s 1.0 min to 10 min 1.0h to 10h 10h to 100h 5s to 50s 5 min to 50 min 5h to 50h 50h to 500h 50 PM4H-A/PM4H-S/PM4H-M All types of PM4H timer have multi-time range. 16 time ranges are selectable. 1s to 500h (Max. range) is controlled. Note: 0 setting is for instantaneous output operation. Specifications Rated operating voltage Rated frequency Rated power consumption Rated control capacity Rating Operating mode Time range Operating time fluctuation Time Setting error accuracy Note:1) Voltage error Temperature error Contact arrangement Contact Life Contact resistance (Initial value) Contact material Mechanical (contact) Electrical (contact) Allowable operating voltage range Insulation resistance (Initial value) Electrical function Breakdown voltage (Initial value) Min. power off time Max. temperature rise Vibration resistance Mechanical function Operating condition Others Shock resistance Functional Destructive Functional Destructive Ambient temperature Ambient humidity Atmospheric pressure Ripple factor (DC type) Protective construction Weight PM4H-A PM4H-S 100 to 240V AC, 48 to 125V DC, 12V DC, 24V AC/DC 50/60Hz common (AC operating type) Approx. 10VA (100 to 240V AC) Approx. 2.5VA (24V AC) Approx. 1.5W (12V DC, 24V DC, 48 to 125V DC) 5A 250V AC (resistive load) PM4H-M Analog Timers Type Item Pulse ON-delay Power ON-delay Pulse Flicker Power Flicker Pulse ON-Flicker Power ON-flicker Differential ON/OFF-delay (1) (2) Power ON-delay Power One-shot Signal OFF-delay Power One-cycle Pulse One-shot (with instantaneous contact) Pulse One-cycle 1s to 500h (Max.) 16 time ranges switchable 0.3% (power off time change at the range of 0.1s to 1h) 5% (Full-scale value) 0.5% (at the operating voltage changes between 85 to 110%) 2% (at 20 C ambient temp. at the range of -10 to +50 C +14 to +122 F) Timed-out 1 Form C Timed-out 2 Form C Instantaneous 1 Form C Max. 100m (at 1A 6V DC) Silver alloy Au flash on Silver alloy 2 107 105 (at rated control capacity) 85 to 110% of rated operating voltage (at 20 C coil temp.) Between live and dead metal parts Between input and output Min. 100M (At 500V DC) Between contacts of different poles Between contacts of same pole 2,000Vrms for 1 min Between live and dead metal parts 2,000Vrms for 1 min Between input and output 2,000Vrms for 1 min Between contacts of different poles 1,000Vrms for 1 min Between contacts of same pole 100ms 55 C 131 F 65 C 149 F 10 to 55Hz: 1 cycle/min double amplitude of 0.25mm (10min on 3 axes) 10 to 55Hz: 1 cycle/min double amplitude of 0.375mm (1h on 3 axes) Min. 98m/s2 (4 times on 3 axes) Min. 980m/s2 (5 times on 3 axes) -10 to +50 C +14 to +122 F 30 to 85%RH (at 20 C 68 F, non-condensing) 860 to 1,060hPa 20% IP65 on front panel (using rubber gasket ATC18002) <only for IP65 type> 100g 3.527 oz (Pin type) 110g 3.880 oz (Screw terminal type) Note: 1) Unless otherwise specified, the measurement conditions at the maximum scale time standard are specified to be the rated operating voltage (within 5% ripple factor for DC), 20C 68F ambient temperature, and 1s power off time. 2) For the 1s range, the tolerance for each specification becomes 10ms. 09/2009 39 PM4H-A/S/M Terminal layouts and wiring diagrams PM4H-A Pin type * Timed-out 2 Form C PM4H-S Pin type * Timed-out 2 Form C Screw terminal type * Timed-out 2 Form C Screw terminal type * Timed-out 2 Form C Reset input Start input Stop input N.C. N.O. 6 N.C. N.O. 4 3 2 (-) 7 8 9 N.C. 5 6 7 1 11 1 8 9 10 Operating voltage 2 3 4 N.O. 4 5 3 2 5 Stop input (+) (+) Reset input Start input Operating voltage (-) N.C. N.C. N.C. N.O. 10 11 N.O. (-) N.C. N.O. 6 N.O. 7 8 9 10 N.C. N.O. 11 6 7 1 1 8 Operating voltage 2 3 4 5 Operating (+) voltage (-) (+) Analog Timers 1) DC Type PM4H-M Pin type * Timed-out 1 Form C * Instantaneous 1 Form C N.C. N.C. N.O. 4 5 3 2 (-) Pin Screw terminal Connect the terminal 0 to negative PM4H-A (-), and the terminal 8 to positive (+). Connect the terminal x to negative (-), and the terminal PM4H-S Connect the terminal 0 to negative z to positive (+). PM4H-M (-), and the terminal 5 to positive (+). Type Screw terminal type * Timed-out 1 Form C * Instantaneous 1 Form C N.O. N.C. N.O. 6 1 8 9 10 N.C. N.O. 2 3 4 2) Contact 5 Timed-out contact 1 8 Operating voltage 7 11 6 7 (+) (+) Operating voltage (-) Instantaneous contact 3) Voltage should not be applied to the various inputs (reset, start, and stop) of the PM4H-A multi-range timer. These inputs should be input without voltage. Part names PM4H-S PM4H-A Power indicator LED PM4H-M Output indicator LED Hand Time indicator window Time unit indicator Time range selector 16 time settings selectable (1 s to 500 h) 1s 5s 10s 50s 1min 5min 10min 50min 1h 5h 10h 50h 10h 50h 100h 500h Set dial Operation mode indicator Operation mode selector Instantaneous output area When the hand is in this area, instantaneous operation starts. Selectable from 8 operation modes ON : Pulse ON-delay FL : Pulse Flicker FO : Pulse ON-flicker OF1 : Differential ON/OFF-delay (1) SF : Signal OFF-delay OS : Pulse One-shot OF2 : Differential ON/OFF-delay (2) OC : Pulse One-cycle 09/2009 40 Operation mode selector Selectable from 5 operation modes ON : Power ON-delay FL : Power flicker FO : Power ON-flicker OS : Power One-shot OC : Power One-cycle PM4H-A/S/M mm inch Tolerance: p0.5 p.020 Dimensions * PM4H-: Screw terminal type (Flush mount) Pin type (Flush mount/Surface mount) :44.5 :1.752 66.5 2.618 14.5 48 1.890 :44.5 :1.752 Analog Timers 48 1.890 6.0 12.0 .236 .472 48 1.890 41 dia. 1.614 dia. 62.5 2.461 41 dia. 1.614 dia. 6.0 12.0 .236 .472 48 1.890 * Panel mount dimensions (with mounting frame) Screw terminal type Rubber gasket ATC 18002 (attached) Pin type Rubber gasket ATC18002 Panel Panel Mounting frame AT8-DA4 (Sold separately) 48 1.890 48 1.890 :44.5 :1.752 66 2.598 1 .039 50 1.969 50 1.969 Mounting frame AT8-DA4 (attached) 48 1.890 61.5 2.421 66 2.598 72.5 2.854 (8-pin) 78 3.071 (11-pin) 48 1.890 Rear terminal socket AT78041 (8-pin: sold separately) AT78051 (11-pin: sold separately) * Surface mount dimensions Pin type Din rail socket AT8-DF8K (8-pin: sold separately) AT8-DF11K (11-pin: sold separately) Mounting rail AT8-DLA1 97.3 (8-pin) 3.831 104.0 (11-pin) 4.094 * Panel cut out dimensions Standard cut out dimensions are shown below. Use mounting frame (AT8-DA4) and rubber gasket (ATC18002). 45+0.6 0 1.772+.024 0 * Adjacent mounting 45+0.6 0 1.772+.024 0 Min. 80 3.150 A A = (48sn-2.5)+0.6 0 A = (1.890sn-.098)+.024 0 45+0.6 0 1.772+.024 0 Min. 80 3.150 Note) 1. The proper thickness of mounting panel is between 1 to 5mm. 2. Adjacent mount is less water-resistant. 09/2009 41 PM4H-A/S/M Operation mode LED lighting LED flickering T: Setting time t1, t2, ta, tb<T t1+t2=T PM4H-A Operation type Pulse ON-delay Analog Timers ON Explanation Time chart * If using a time-limit start when the power is turned on, and a reset when the power is turned off, pins 2 to 6 (screw-tightening pins x and c) should be shorted ahead of time. * Turn the operation mode selector switch to the ON position. If pins 2 to 6 (screw-tightening pins x and c) are shorted (the start input is turned on) with the power supply on, the output will go on after the set time has elapsed. If the power supply is turned off, or pins 2 to 7 (screw-tightening pins x to v) are shorted (the reset input is turned on), a reset is carried out. Note) During time-limited operation, the time-limited operation is stopped while the pins 2 to 5 (screw-tightening pins x to b) are being shorted (the stop input is on). When the pins are released, time-limited operation resumes. ON OFF Power supply ON Pulse Flicker FL Pulse ON-flicker FO Differential ON/OFF-delay (1) OF1 Signal OFF-delay SF * If using a time-limit start when the power is turned on, and a reset when the power is turned off, pins 2 to 6 (screw-tightening pins x and c) should be shorted ahead of time. * Turn the operation mode selector switch to the FO position. When pins 2 to 6 (screw-tightening pins x and c) are shorted (the start input is turned on) with the power supply on, the output goes on, and after the set time has elapsed, it goes off. This process is subsequently repeated. If the power supply is turned off, or pins 2 to 7 (screw-tightening pins x to v) are shorted (the reset input is turned on), a reset is carried out. Note) During time-limited operation, the time-limited operation is stopped while the pins 2 to 5 (screw-tightening pins x to b) are being shorted (the stop input is on). When the pins are released, time-limited operation resumes. * Turn the operation mode selector switch to the OF1 position. When pins 2 to 6 (screw-tightening pins x and c) are shorted (the start input is turned on) with the power supply on, the output goes on, and after the set time has elapsed, it goes off. Also, when pins 2 to 6 are released (the start input goes off), the output goes on, and after the set time has elapsed, it goes off. If the status of pins 2 to 6 (screw-tightening pins x and c) changes during the time-limit interval (the start input goes from on to off, or from off to on), the time-limit interval is restarted from the point at which the change took place. If the power supply is turned off, or pins 2 to 7 (screw-tightening pins x to v) are shorted (the reset input is turned on), a reset is carried out. Note) During time-limited operation, the time-limited operation is stopped while the pins 2 to 5 (screw-tightening pins x to b) are being shorted (the stop input is on). When the pins are released, time-limited operation resumes. * Turn the operation mode selector switch to the SF position. When pins 2 to 6 (screw-tightening pins x and c) are shorted (the start input is turned on) with the power supply on, the output goes on, and when pins 2 to 6 (screw-tightening pins x and c) are released (the start input is turned off), the time limit interval begins. After the set time has elapsed, the output goes off. If start input is entered at any point during the time limit interval, the time limit interval is reset. Note) During time-limited operation, the time-limited operation is stopped while the pins 2 to 5 (screw-tightening pins x to b) are being shorted (the stop input is on). When the pins are released, time-limited operation resumes. ON OFF Start 0-4 OFF ON OFF Reset 0-5 ON OFF Stop 0-3 T t1 t2 ON ON OFF Time out (N.O. contact) OFF OP. LED POWER LED Note: * If using a time-limit start when the power is turned on, and a reset when the power is turned off, pins 2 to 6 (screw-tightening pins x and c) should be shorted ahead of time. * Turn the operation mode selector switch to the FL position. When pins 2 to 6 (screw-tightening pins x and c) are shorted (the start input is turned on) with the power supply on, the limited time interval begins, and the output goes on after the set time has elapsed. After the output has gone on, it goes off when the set time has elapsed, and this process is subsequently repeated. If the power supply is turned off, or pins 2 to 7 (screw-tightening pins x to v) are shorted (the reset input is turned on), a reset is carried out. Note) During time-limited operation, the time-limited operation is stopped while the pins 2 to 5 (screw-tightening pins x to b) are being shorted (the stop input is on). When the pins are released, time-limited operation resumes. ON LED lighting or No LED lighting ON OFF Power supply ON ON OFF Start 0-4 ON OFF OFF ON OFF Reset 0-5 ON OFF Stop 0-3 T T t1 ta t2 tb ON ON OFF Time out (N.O. contact) OFF OP. LED POWER LED Note: LED lighting or No LED lighting ON OFF Power supply ON ON ON OFF Start 0-4 OFF OFF ON OFF Reset 0-5 ON Stop OFF 0-3 T T ta t2 t1 T tb ON OFF Time out (N.O. contact) OFF OP. LED POWER LED ON OFF Power supply ON ON OFF Start 0-4 OFF ON OFF Reset 0-5 ON Stop OFF 0-3 T t1 ON t2 ta OFF Time out (N.O. contact) tb ON ON OFF OFF OP. LED Restart POWER LED Note: LED lighting or No LED lighting ON OFF Power supply ON ON OFF Start 0-4 OFF ON OFF Reset 0-5 ON Stop OFF 0-3 T ta tb ON Time out (N.O. contact) OFF OP. LED POWER LED Note: Note: Keep 0.1s or more for power off time. Keep 0.05s or more for start, stop, reset input time. 09/2009 42 LED lighting or No LED lighting PM4H-A/S/M Pulse One-shot OS Explanation Time chart * If using a time-limit start when the power is turned on, and a reset when the power is turned off, pins 2 to 6 (screw-tightening pins x and c) should be shorted ahead of time. * Turn the operation mode selector switch to the OS position. When pins 2 to 6 (screw-tightening pins x and c) are shorted (the start input is turned on) with the power supply on, the output goes on for the set time limit interval. If the power supply is turned off, or pins 2 to 7 (screw-tightening pins x to v) are shorted (the reset input is turned on), a reset is carried out. Note) During time-limited operation, the time-limited operation is stopped while the pins 2 to 5 (screw-tightening pins x to b) are being shorted (the stop input is on). When the pins are released, time-limited operation resumes. ON OFF Power supply ON Start OFF 0-4 Differential ON/OFF-delay (2) OF2 Pulse One-cycle OC Note: * If using a time-limit start when the power is turned on, and a reset when the power is turned off, pins 2 to 6 (screw-tightening pins x and c) should be shorted ahead of time. * Turn the operation mode selector switch to the OC position. When pins 2 to 6 (screw-tightening pins x and c) are shorted (the start input is turned on) with the power supply on, the output goes on after the set time limit interval has elapsed. After it has gone on, it goes off after one pulse (approximately 0.8 seconds). If the power supply is turned off, or pins 2 to 7 (screw-tightening pins x to v) are shorted (the reset input is turned on), a reset is carried out. Note) During time-limited operation, the time-limited operation is stopped while the pins 2 to 5 (screw-tightening pins x to b) are being shorted (the stop input is on). When the pins are released, time-limited operation resumes. OFF ON OFF Reset 0-5 ON Stop OFF 0-3 T T t1 ta t2 ON OFF Time out (N.O. contact) OP. LED POWER LED Note: * Turn the operation mode selector switch to the OF2 position. When pins 2 to 6 (screw-tightening pins x and c) are shorted (the start input is turned on) with the power supply on, the time limit interval begins, and after the set time interval has elapsed, the output goes on. Also, when pins 2 to 6 are released (the start input goes off), the time limit interval begins, and after it has elapsed, the output goes off. If the status of pins 2 to 6 (screw-tightening pins x and c) changes during the time-limit interval (the start input goes from on to off, or from off to on), the time limit interval is restarted from the point at which the change took place. If the power supply is turned off, or pins 2 to 7 (screw-tightening pins x to v) are shorted (the reset input is turned on), a reset is carried out. Note) During time-limited operation, the time-limited operation is stopped while the pins 2 to 5 (screw-tightening pins x to b) are being shorted (the stop input is on). When the pins are released, time-limited operation resumes. ON LED lighting or No LED lighting ON OFF Power supply ON ON OFF Start 0-4 OFF ON OFF Reset 0-5 ON Stop OFF 0-3 T t1 t2 ta ON tb ON OFF OFF Time out (N.O. contact) OP. LED Restart POWER LED Note: LED lighting or No LED lighting ON OFF Power supply ON ON ON OFF Start 0-4 OFF OFF ON ON OFF OFF Reset 0-5 ON Stop OFF 0-3 T t ta t1 ON t2 t OFF Time out (N.O. contact) tb ON OFF OP. LED POWER LED One pulse time (t): Approx. 0.8s Note: LED lighting or No LED lighting Keep 0.1s or more for power off time. Keep 0.05s or more for start, stop, reset input time. LED lighting T: Setting time PM4H-S Operation type Power ON-delay Explanation LED flickering Time chart Time limit contact relay When the power supply is turned on, the output goes on after the set time interval has elapsed. When the power supply is turned off, a reset is carried out. ON OFF Power supply T Time out (N.O. contact) ON OFF OP. LED POWER LED PM4H-M Operation type Explanation Power ON-delay Turn the operation mode selector switch to display the various operations. When the power supply is turned on, the time limit interval begins, and operation is carried out. When the power supply is turned off, a reset is carried out. ON Power Flicker FL Power ON-flicker Time chart Power ON-delay ON OFF Power supply ON OFF Time out (N.O. contact) T ON FO Instantaneous contact (N.O. contact) OFF Power One-shot OP. LED OS POWER LED Power One-cycle OC Note: Keep 0.1s or more for power off time. PM4H-M timers do not have each input which is start, reset and stop. 09/2009 43 Analog Timers Operation type