FB
SW
L1
RFB2
LM34922
BST CBST
D1
CS
RT
VIN
6V to 28V
Input
CIN
SS
CSS
RT
SGND
PGD CSG
RS
RPGD
VPGD COUT
RFB1
VOUT
Power
Good
LM34922
www.ti.com
SNVS813A –JUNE 2012–REVISED MARCH 2013
LM34922 28V, 2A Constant On-Time Switching Regulator with Adjustable Current Limit
Check for Samples: LM34922
1FEATURES • Thermal Shutdown
• Precision 2% Feedback Reference
2• Input Operating Voltage Range: 6V to 28V
• Absolute Maximum Input Rating: 30V DESCRIPTION
• Integrated 2A N-Channel Buck Switch The LM34922 Constant On-time Step-Down
• Adjustable Current Limit Allows for Smaller Switching Regulator features all the functions needed
Inductor to implement a low cost, efficient, buck bias regulator
capable of supplying up to 2A of load current. This
• Adjustable Output Voltage from 2.51V voltage regulator contains an N-Channel Buck switch,
• Minimum Ripple Voltage at VOUT a startup regulator, current limit detection, and
• Power Good Output internal ripple control. The constant on-time
regulation principle requires no loop compensation,
• Switching Frequency Adjustable to 1MHz results in fast load transient response, and simplifies
• COT Topology Features: circuit implementation. The operating frequency
– Switching Frequency Remains Nearly remains constant with line and load. The adjustable
Constant with Load Current and Input valley current limit detection results in a smooth
Voltage Variations transition from constant voltage to constant current
mode when current limit is reached, without the use
– Ultra-Fast Transient Response of current limit foldback. The PGD output indicates
– No Loop Compensation Required the output voltage has increased to within 5% of the
– Stable Operation with Ceramic Output expected regulation value. Additional features
Capacitors include: Low output ripple, VIN under-voltage lock-
out, adjustable soft-start timing, thermal shutdown,
– Allows for Smaller Output Capacitor and gate drive pre-charge, gate drive under-voltage lock-
Current Sense Resistor out, and maximum duty cycle limit.
• Adjustable Soft-Start Timing
Typical Application, Basic Step-Down Regulator
1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Copyright © 2012–2013, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
SW
BST
FB
CS
CSG
RT
VIN
PGD
SGND
SS
Exposed Pad on Bottom
Connect to Ground
1
2
3
4
5
10
9
8
7
6
LM34922
SNVS813A –JUNE 2012–REVISED MARCH 2013
www.ti.com
Connection Diagram
Figure 1. Top View
10-Lead HVSSOP-PowerPAD
PIN DESCRIPTIONS
Pin No. Name Description Application Information
1 VIN Input supply voltage Operating input range is 6V to 28V. Transient capability is 30V. A low ESR
capacitor must be placed as close as possible to the VIN and SGND pins.
2 RT On-time Control An external resistor from VIN to this pin sets the buck switch on-time, and the
switching frequency.
3 PGD Power Good Logic output indicates when the voltage at the FB pin has increased to above
95% of the internal reference voltage. Hysteresis is provided. An external
pull-up resistor to a voltage less than 7V is required.
4 SS Soft-Start An internal current source charges an external capacitor to provide the soft-
start function.
5 SGND Signal Ground Ground for all internal circuitry other than the current limit sense circuit.
6 FB Feedback Internally connected to the regulation comparator. The regulation level is
2.51V.
7 CSG Current Sense Ground Ground connection for the current limit sensing circuit. Connect to ground
and to the current sense resistor.
8 CS Current sense Connect to the current sense resistor and the anode of the free-wheeling
diode.
9 SW Switching Node Internally connected to the buck switch source. Connect to the external
inductor, cathode of the free-wheeling diode, and bootstrap capacitor.
10 BST Bootstrap capacitor connection of the Connect a 0.1µF capacitor from SW to this pin. The capacitor is charged
buck switch gate driver. during the buck switch off-time via an internal diode.
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
2Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM34922
LM34922
www.ti.com
SNVS813A –JUNE 2012–REVISED MARCH 2013
Absolute Maximum Ratings (1)(2)(3)
VIN to SGND (TJ= 25°C) 30V
BST to SGND 37V
SW to SGND (Steady State) -1.5V to 30V
BST to SW -0.3V to 7V
CS to CSG -0.3V to 0.3V
CSG to SGND -0.3V to 0.3V
PGD to SGND -0.3V to 7V
SS to SGND -0.3V to 3V
RT to SGND -0.3V to 1V
FB to SGND -0.3V to 7V
ESD Rating (4) Human Body Model 2kV
Storage Temperature Range -65°C to +150°C
For soldering specs see: SNOA549C
Junction Temperature 150°C
(1) Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which
operation of the device is intended to be functional. For specifications and test conditions, see the Electrical Characteristics.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(3) Current flow out of a pin is indicated as a negative number.
(4) The human body model is a 100pF capacitor discharged through a 1.5kΩresistor into each pin.
Operating Ratings (1)
VIN Voltage 6.0V to 28V
Junction Temperature –40°C to +125°C
(1) Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which
operation of the device is intended to be functional. For specifications and test conditions, see the Electrical Characteristics.
Electrical Charateristics
Specifications with standard type are for TJ= 25°C only; limits in boldface type apply over the full Operating Junction
Temperature (TJ) range. Minimum and Maximum limits are specified through test, design, or statistical correlation. Typical
values represent the most likely parametric norm at TJ= 25°C, and are provided for reference purposes only. Unless
otherwise stated the following conditions apply: VIN = 12V, RT= 50kΩ.
Symbol Parameter Conditions Min Typ Max Units
Input (VIN Pin)
IIN Input operating current Non-switching, FB = 3V 1200 1600 µA
UVLOVIN VIN under-voltage lock-out threshold VIN Increasing 4.6 5.3 5.9 V
VIN under-voltage lock-out threshold 200 mV
hysteresis
Switch Characteristics
RDS(ON) Buck Switch RDS(ON) ITEST = 200mA 0.3 0.6 Ω
UVLOGD Gate Drive UVLO BST-SW 2.4 3.4 4.4 V
UVLOGD Hysteresis 350 mV
Pre-charge switch voltage ITEST = 10mA into SW pin 1.4 V
Pre-charge switch on-time 120 ns
Soft-Start Pin
VSS Pull-up voltage 2.51 V
ISS Internal current source 10 µA
VSS-SH Shutdown Threshold 70 140 mV
Current Limit
Copyright © 2012–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LM34922
LM34922
SNVS813A –JUNE 2012–REVISED MARCH 2013
www.ti.com
Electrical Charateristics (continued)
Specifications with standard type are for TJ= 25°C only; limits in boldface type apply over the full Operating Junction
Temperature (TJ) range. Minimum and Maximum limits are specified through test, design, or statistical correlation. Typical
values represent the most likely parametric norm at TJ= 25°C, and are provided for reference purposes only. Unless
otherwise stated the following conditions apply: VIN = 12V, RT= 50kΩ.
Symbol Parameter Conditions Min Typ Max Units
VILIM Threshold voltage at CS -146 -130 -115 mV
CS bias current FB = 3V -120 µA
CSG bias current FB = 3V -35 µA
On Timer, RT Pin
tON - 1 On-time VIN = 12V, RT= 50kΩ150 200 250 ns
tON - 2 On-time (current limit) VIN = 12V, RT= 50kΩ100 ns
tON - 3 On-time VIN = 12V, RT= 301kΩ1020 ns
tON - 4 On-time VIN = 9V, RT= 30.9kΩ130 171 215 ns
tON - 5 On-time VIN = 12V, RT= 30.9kΩ105 137 170 ns
tON - 6 On-time VIN = 16V, RT= 30.9kΩ79 109 142 ns
Off Timer
tOFF Minimum Off-time (LM34922) 90 150 208 ns
Regulation Comparator (FB Pin)
VREF FB regulation threshold SS pin = steady state 2.46 2.51 2.56 V
FB bias current FB = 3V 100 nA
Power Good (PGD pin)
Threshold at FB, with respect to VREF FB increasing 91 95 %
Threshold hysteresis 3.3 %
PGDVOL Low state voltage IPGD = 1mA, FB = 0V 125 180 mV
PGDLKG Off state leakage VPGD = 7V, FB = 3V 0.1 µA
Thermal Shutdown
TSD Thermal shutdown Junction temperature increasing 155 °C
Thermal shutdown hysteresis 20 °C
Thermal Resistance
θJA Junction to Ambient, 0 LFPM Air Flow (1) 48 °C/W
θJC Junction to Case,(1) 10 °C/W
(1) JEDEC test board description can be found in JESD 51-5 and JESD 51-7.
4Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM34922
010 30
VIN (V)
10
100
1000
10000
ON-TIME (ns)
205 2515
RT = 500k
300k
50k
100k 200k
LM34922
www.ti.com
SNVS813A –JUNE 2012–REVISED MARCH 2013
Typical Performance Characteristics
On-Time
vs
Efficiency (Circuit of Figure 19) VIN and RT
Figure 2. Figure 3.
Voltage at the RT Pin Shutdown Current into VIN
Figure 4. Figure 5.
PGD Low Voltage
vs.
Operating Current into VIN Sink Current
Figure 6. Figure 7.
Copyright © 2012–2013, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LM34922
LM34922
SNVS813A –JUNE 2012–REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
Reference Voltage Current Limit Threshold
vs. vs.
Temperature Temperature
Figure 8. Figure 9.
Operating Current VIN UVLO
vs. vs.
Temperature Temperature
Figure 10. Figure 11.
SS Pin ShutdownThreshold On-Time
vs. vs.
Temperature Temperature
Figure 12. Figure 13.
6Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM34922
UVLO
VIN
SW Pin
Inductor
Current
SS Pin
t1
PGD
VOUT
SS
RT
FB
VIN
SW
VIN
BST
L1
CBST
D1
SD
CS
LEVEL
SHIFT
ON TIMER
FINISH START
LOGIC
Gate Drive
UVLO
5V REGULATOR
Input CL
CL
2.5V
REGULATION
COMPARATOR
LM34922
10
PA
CURRENT
LIMIT COMPARATOR
FINISH
START
OFF TIMER THERMAL
SHUTDOWN
FCIC
CONTROL
PGD
2.375V
0.8V
RPGD
CSG
Power
Good 125 mV
UVLO
SGND
RS
+
-
CURRENT LIMIT
THRESHOLD
+
-
6V to 28V
CBYP
CIN
RT
CSS
COUT
VOUT
RFB2
RFB2
+
-
+
-
Pre-Chg
LM34922
SNVS813A –JUNE 2012–REVISED MARCH 2013
www.ti.com
Block Diagram
WHITE SPACE
Figure 15. Startup Sequence
8Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM34922
FS = VOUT2 x L1 x 1.19 x 1021
RL x RT2
DC = tON
tON + tOFF =
= tON x FSVOUT
VIN
FS = VOUT
(4.1 x 10-11 x (RT + 0.5k)) + (VIN x 15 ns)
LM34922
www.ti.com
SNVS813A –JUNE 2012–REVISED MARCH 2013
FUNCTIONAL DESCRIPTION
The LM34922 Constant On-time Step-down Switching Regulator features all the functions needed to implement a
low cost, efficient buck bias power converter capable of supplying up to 2.0A to the load. This high voltage
regulator contains an N-Channel buck switch, is easy to implement, and is available in a 10-pin HVSSOP-
PowerPAD power enhanced package. The regulator’s operation is based on a constant on-time control principle
with the on-time inversely proportional to the input voltage. This feature results in the operating frequency
remaining relatively constant with load and input voltage variations. The constant on-time feedback control
principle requires no loop compensation resulting in very fast load transient response. The adjustable valley
current limit detection results in a smooth transition from constant voltage to constant current when current limit is
reached. To aid in controlling excessive switch current due to a possible saturating inductor the on-time is
reduced by ≊40% when current limit is detected. The Power Good output (PGD pin) indicates when the output
voltage is within 5% of the expected regulation voltage.
The LM34922 can be implemented to efficiently step-down higher voltages in non-isolated applications.
Additional features include: Low output ripple, VIN under-voltage lock-out, adjustable soft-start timing, thermal
shutdown, gate drive pre-charge, gate drive under-voltage lock-out, and maximum duty cycle limit.
Control Circuit Overview
The LM34922 buck regulator employs a control principle based on a comparator and a one-shot on-timer, with
the output voltage feedback (FB) compared to an internal reference (2.51V). If the FB voltage is below the
reference the internal buck switch is switched on for the one-shot timer period, which is a function of the input
voltage and the programming resistor (RT). Following the on-time the switch remains off until the FB voltage falls
below the reference, but never less than the minimum off-time forced by the off-time one-shot timer. When the
FB pin voltage falls below the reference and the off-time one-shot period expires, the buck switch is then turned
on for another on-time one-shot period.
When in regulation, the LM34922 operates in continuous conduction mode at heavy load currents and
discontinuous conduction mode at light load currents. In continuous conduction mode the inductor’s current is
always greater than zero, and the operating frequency remains relatively constant with load and line variations.
The minimum load current for continuous conduction mode is one-half the inductor’s ripple current amplitude.
The approximate operating frequency is calculated as follows:
(1)
The buck switch duty cycle is approximately equal to:
(2)
When the load current is less than one half the inductor’s ripple current amplitude the circuit operates in
discontinuous conduction mode. The off-time is longer than in continuous conduction mode while the inductor
current is zero, causing the switching frequency to reduce as the load current is reduced. Conversion efficiency is
maintained at light loads since the switching losses are reduced with the reduction in load and frequency. The
approximate discontinuous operating frequency can be calculated as follows:
where
• RL= the load resistance
• L1 is the circuit’s inductor (3)
The output voltage is set by the two feedback resistors (RFB1, RFB2 in the Block Diagram). The regulated output
voltage is calculated as follows:
VOUT = 2.51V x (RFB1 + RFB2) / RFB1 (4)
Copyright © 2012–2013, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LM34922
RT = VOUT - (VIN x FS x 15 ns)
FS x 4.1 x 10-11 - 500:
tON = (VIN)
4.1 x 10-11 x (RT + 500:) + 15 ns
LM34922
SNVS813A –JUNE 2012–REVISED MARCH 2013
www.ti.com
Ripple voltage, which is required at the input of the regulation comparator for proper output regulation, is
generated internally in the LM34922. In the LM34922 the ERM (Emulated Ripple Mode) control circuit generates
the required internal ripple voltage from the ripple waveform at the CS pin.
On-Time Timer
The on-time for the LM34922 is determined by the RTresistor and the input voltage (VIN), calculated from:
(5)
The inverse relationship with VIN results in a nearly constant frequency as VIN is varied. To set a specific
continuous conduction mode switching frequency (FS), the RTresistor is determined from the following:
(6)
The on-time must be chosen greater than 90ns for proper operation. Equation 1,Equation 5 and Equation 6 are
valid only during normal operation - i.e., the circuit is not in current limit. When the LM34922 operates in current
limit, the on-time is reduced by ≊40%. This feature reduces the peak inductor current which may be excessively
high if the load current and the input voltage are simultaneously high. This feature operates on a cycle-by-cycle
basis until the load current is reduced and the output voltage resumes its normal regulated value. The maximum
continuous current into the RT pin must be less than 2mA. For high frequency applications, the maximum
switching frequency is limited at the maximum input voltage by the minimum on-time one-shot period (90ns). At
minimum input voltage the maximum switching frequency is limited by the minimum off-time one-shot period,
which, if reached, prevents achievement of the proper duty cycle.
Current Limit
Current limit detection occurs during the off-time by monitoring the voltage across the external current sense
resistor RS. Referring to the Block Diagram, during the off-time the recirculating current flows through the
inductor, through the load, through the sense resistor, and through D1 to the inductor. If the voltage across the
sense resistor exceeds the threshold (VILIM) the current limit comparator output switches to delay the start of the
next on-time period. The next on-time starts when the recirculating current decreases such that the voltage
across RSreduces to the threshold and the voltage at FB is below 2.51V. The operating frequency is typically
lower due to longer-than-normal off-times. When current limit is detected, the on-time is reduced by ≊40% if the
voltage at the FB pin is below its threshold when the voltage across RSreduces to its threshold (VOUT is low due
to current limiting).
Figure 16 illustrates the inductor current waveform during normal operation and in current limit. During the first
“Normal Operation” the load current is I01, the average of the inductor current waveform. As the load resistance is
reduced, the inductor current increases until the lower peak of the inductor ripple current exceeds the threshold.
During the “Current Limited” portion of Figure 16, each on-time is reduced by ≊40%, resulting in lower ripple
amplitude for the inductor’s current. During this time the LM34922 is in a constant current mode with an average
load current equal to the current limit threshold plus half the ripple amplitude (IOCL), and the output voltage is
below the normal regulated value. Normal operation resumes when the load current is reduced (to IO2), allowing
VOUT and the on-time to return to their normal values. Note that in the second period of “Normal Operation”, even
though the inductor’s peak current exceeds the current limit threshold during part of each cycle, the circuit is not
in current limit since the inductor current falls below the current limit threshold during each off time. The peak
current allowed through the buck switch is 3.5A, and the maximum allowed average current is 2.0A.
10 Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM34922
Voltage
at CS
0V
VRIPPLE
tOFF tON
Inductor
Current 'I
(3a)
Current
LimitThreshold
Normal
Operation
Load
Current
Increases Current
Limited
'I
Inductor
Current
Decreases
Load Current Normal
Operation
Voltage at the FB Pin
2.51V
Voltage at the CS Pin
0V
IPK
IO1
IO2
IOCL
LM34922
www.ti.com
SNVS813A –JUNE 2012–REVISED MARCH 2013
Figure 16. Normal and Current Limit Operation
Ripple Requirements
The LM34922 requires a minimum of 15mVp-p ripple voltage at the CS pin. That ripple voltage is generated by
the decreasing recirculating current (the inductor’s ripple current) through RSduring the off-time. See Figure 17.
Figure 17. CS Pin Waveform
The ripple voltage is equal to:
VRIPPLE =ΔI x RS
where
•ΔI is the inductor current ripple amplitude
• RSis the current sense resistor at the CS pin (7)
N-Channel Buck Switch and Driver
The LM34922 integrates an N-Channel buck switch and associated floating high voltage gate driver. The gate
driver circuit works in conjunction with an external bootstrap capacitor (CBST) and an internal high voltage diode.
A 0.1µF capacitor connected between BST and SW provides the supply voltage for the driver during the on-time.
During each off-time, the SW pin is at approximately -1V, and CBST is recharged from the internal 5V regulator for
the next on-time. The minimum off-time ensures a sufficient time each cycle to recharge the bootstrap capacitor.
Copyright © 2012–2013, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LM34922
RUN
LM34922
SS
CSS
STOP
LM34922
SNVS813A –JUNE 2012–REVISED MARCH 2013
www.ti.com
Soft-Start
The soft-start feature allows the converter to gradually reach a steady state operating point, thereby reducing
startup stresses and current surges. Upon turn-on, when VIN reaches its under-voltage lock-out threshold an
internal 10µA current source charges the external capacitor at the SS pin to 2.51V (t1 in Figure 15). The ramping
voltage at SS ramps the non-inverting input of the regulation comparator, and the output voltage, in a controlled
manner. For proper operation, the soft-start capacitor should be no smaller than 1000pF.
The LM34922 can be employed as a tracking regulator by applying the controlling voltage to the SS pin. The
regulator’s output voltage tracks the applied voltage, gained up by the ratio of the feedback resistors. The applied
voltage at the SS pin must be within the range of 0.5V to 2.6V. The absolute maximum rating for the SS pin is
3.0V. If the tracking function causes the voltage at the FB pin to go below the thresholds for the PGD pin, the
PGD pin will switch low (see the Power Good Output (PGD) section). An internal switch grounds the SS pin if the
input voltage at VIN is below its under-voltage lock-out threshold or if the Thermal Shutdown activates. If the
tracking function (described above) is used, the tracking voltage applied to the SS pin must be current limited to
a maximum of 1mA.
Shutdown Function
The SS pin can be used to shutdown the LM34922 by grounding the SS pin as shown in Figure 18. Releasing
the pin allows normal operation to resume.
Figure 18. Shutdown Implemetation
Power Good Output (PGD)
The Power Good output (PGD) indicates when the voltage at the FB pin is close to the internal 2.51V reference
voltage. The rising threshold at the FB pin for the PGD output to switch high is 95% of the internal reference. The
falling threshold for the PGD output to switch low is approximately 3.3% below the rising threshold.
The PGD pin is internally connected to the drain of an N-channel MOSFET switch. An external pull-up resistor
(RPGD), connected to an appropriate voltage not exceeding 7V, is required at PGD to indicate the LM34922’s
status to other circuitry. When PGD is low, the pin’s voltage is determined by the current into the pin. See the
graph “ PGD Low Voltage vs. Sink Current”.
Upon powering up the LM34922, the PGD pin is high until the voltage at VIN reaches 2V, at which time PGD
switches low. As VIN is increased PGD stays low until the output voltage takes the voltage at the FB pin above
95% of the internal reference voltage, at which time PGD switches high. As VIN is decreased (during shutdown)
PGD remains high until either the voltage at the FB pin falls below ≊92% of the internal reference, or when VIN
falls below its lower UVLO threshold, whichever occurs first. PGD then switches low, and remains low until VIN
falls below 2V, at which time PGD switches high. If the LM34922 is used as a tracking regulator (see the Soft-
Start section), the PGD output is high as long as the voltage at the FB pin is above the thresholds mentioned
above.
Thermal Shutdown
The LM34922 should be operated so the junction temperature does not exceed 125°C. If the junction
temperature increases above that, an internal Thermal Shutdown circuit activates (typically) at 155°C, taking the
controller to a low power reset state by disabling the buck switch and taking the SS pin to ground. This feature
helps prevent catastrophic failures from accidental device overheating. When the junction temperature reduces
below 135°C (typical hysteresis = 20°C) normal operation resumes.
12 Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM34922
L1 10 PH
D1
CSS
RS
CIN CBYP
RT
118 k:
10 k:
0.022 PF
80 m:
5V
FB
SW
LM34922
BST
CS
RT
VIN
SS
SGND
PGD CSG
8V to 28V
Input
4.7 PF0.1 PF
RPGD
VPGD
Power
Good
4.99 k:
RFB2
CBST
COUT
RFB1
VOUT
4.99 k:
0.1 PF
10 PF
LM34922
www.ti.com
SNVS813A –JUNE 2012–REVISED MARCH 2013
Figure 19. Example Circuit
Figure 20. Efficiency (Circuit of Figure 19)
Figure 21. Frequency vs VIN (Circuit of Figure 19)
Copyright © 2012–2013, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LM34922
LM34922
SNVS813A –JUNE 2012–REVISED MARCH 2013
www.ti.com
REVISION HISTORY
Changes from Original (March 2013) to Revision A Page
• Changed layout of National Data Sheet to TI format .......................................................................................................... 13
14 Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM34922
PACKAGE OPTION ADDENDUM
www.ti.com 3-Dec-2016
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM34922MY/NOPB ACTIVE MSOP-
PowerPAD DGQ 10 1000 Green (RoHS
& no Sb/Br) CU SN Level-3-260C-168 HR -40 to 125 SA8B
LM34922MYX/NOPB ACTIVE MSOP-
PowerPAD DGQ 10 3500 Green (RoHS
& no Sb/Br) CU SN Level-3-260C-168 HR -40 to 125 SA8B
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
PACKAGE OPTION ADDENDUM
www.ti.com 3-Dec-2016
Addendum-Page 2
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM34922MY/NOPB MSOP-
Power
PAD
DGQ 10 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LM34922MYX/NOPB MSOP-
Power
PAD
DGQ 10 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 20-Sep-2016
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM34922MY/NOPB MSOP-PowerPAD DGQ 10 1000 210.0 185.0 35.0
LM34922MYX/NOPB MSOP-PowerPAD DGQ 10 3500 367.0 367.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 20-Sep-2016
Pack Materials-Page 2
MECHANICAL DATA
DGQ0010A
www.ti.com
MUC10A (Rev A)
BOTTOM VIEW
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated
