Chip tantalum capacitors TC Series A Case Features (A) 1) Vital for all hybrid integrated circuits board application. 2) Wide capacitance range. 3) Screening by thermal shock. Dimensions (Unit : mm) Anode mark (Unit : mm) W1 L H W2 S S + - Dimensions A case L 3.2 + - 0.2 W1 1.6 + - 0.2 W2 1.2 + - 0.2 H 1.6 + - 0.2 S 0.8 + - 0.3 Part No. Explanation T C A 1 2 0 J 1 3 0 6 4 M 8 R 5 6 4 Nominal capacitance 1 Series name Nominal capacitance in pF in 3 digits: 2 significant figures followed by the figure representing the number of 0's. TC 2 Case style A 5 Capacitance tolerance M: + - 20% 3 Rated voltage Rated voltage (V) CODE 4 6.3 10 16 20 25 35 0G 0J 1A 1C 1D 1E 1V 6 Taping 8 : Reel width : 8mm R : Positive electrode on the side opposite to sprocket hole www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. 1/7 2012.02 - Rev.G TC Series A Case Data Sheet Rated table Rated voltage (V.DC) (F) 6.3 4 10 16 20 25 35 A A A A 1.0 (105) 1.5 (155) A A A A 2.2 (225) A A A A A A A A A 4.7 (475) A A A A A A 6.8 (685) A A A A 10 (106) A A A A 15 (156) A A A 22 (226) A A A 33 (336) A A 47 (476) A A 68 (686) A 100 (107) A 3.3 (335) 150 (157) Remark) Case size codes (A) in the above show products line-up. Under development Marking The indications listed below should be given on the surface of a capacitor. (1) Polarity : The polarity should be shown by bar. (on the anode side) (2) Rated DC voltage : Due to the small size of A case, a voltage code is used as shown below. (3) Visual typical example (1) voltage code (2) capacitance code Voltage Code g Rated DC Voltage (V) 4 Capacitance Code A Nominal Capacitance (F) 1.0 [A case] j 6.3 E 1.5 A 10 J 2.2 C 16 N 3.3 D 20 S 4.7 E 25 W 6.8 V 35 a 10 e 15 j 22 n 33 note 1) s 47 w 68 a 100 j a - - (1) (2) j a manufacture code note 2) voltage code and capacitance code are variable with parts number www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. 2/7 2012.02 - Rev.G TC Series A Case Data Sheet Characteristics Performance Item Operating Temperature -55C~+125C Maximum operating temperature with no voltage derating +85C Rated voltage (VDC) Category voltage (VDC) Test conditions (based on JIS C 5101-1 and JIS C 5101-3) Voltage reduction when temperature exceeds +85C 4 6.3 10 16 20 25 35 at 85C 2.5 4 6.3 10 13 16 22 at 125C at 85C Surge voltage (VDC) 5 DC Leakage current 0.5A or 0.01CV whichever is greater Shown in " Standard list " As per 4.9 JIS C 5101-1 As per 4.5.1 JIS C 5101-3 Voltage : Rated voltage for 1min Capacitance tolerance Shall be satisfied allowance range. 20% As per 4.7 JIS C 5101-1 As per 4.5.2 JIS C 5101-3 Measuring frequency : 12012Hz Measuring voltage : 0.5Vrms +1.5 to 2V.DC Measuring circuit : DC Equivalent series circuit Tangent of loss angle (Df, tan ) Shall be satisfied the voltage on " Standard list " As per 4.8 JIS C 5101-1 As per 4.5.3 JIS C 5101-3 Measuring frequency : 12012Hz Measuring voltage : 0.5Vrms +1.5 to 2V.DC Measuring circuit : DC Equivalent series circuit Impedance Shall be satisfied the voltage on " Standard list " As per 4.10 JIS C 5101-1 As per 4.5.4 JIS C 5101-3 Measuring frequency : 10010kHz Measuring voltage : 0.5Vrms or less Measuring circuit : DC Equivalent series circuit Resistance to Soldering heat Appearance L.C. C / C Df (tan ) Temperature cycle Moisture resistance 8 13 20 26 32 44 As per 4.14 JIS C 5101-1 As per 4.6 JIS C 5101-3 Dip in the solder bath Less than initial limit Solder temp : 26010C : 50.5s TCA0G686M8R : Within 15% of initial value Duration :1 TCA0G107M8R : Within 20% of initial value Repetition After the specimens, leave it at room temperature for : Within 5% of initial value Others over 24h and then measure the sample. Less than initial limit There should be no significant abnormality. The indications should be clear. Appearance There should be no significant abnormality. The indications should be clear. L.C. TCAP0J226 : Less than 150% of initial limit : Less than initial limit Others C / C TCA0G686M8R : Within 15% of initial value TCA0G107M8R : Within 20% of initial value TCA0J476M8R : Within 15% of initial value TCA1A226M8R : Within 15% of initial value : Within 10% of initial value Others Less than initial limit Appearance There should be no significant abnormality. The indications should be clear. C / C Df (tan ) Temp. Time 1 -55 + - 3C 303min. 2 Room temp. + 2C 125 - 3min.or less 3 4 Room temp. 3min.or less 303min. After the specimens, leave it at room temperature for over 24h and then measure the sample. Df (tan ) L.C. As per 4.16 JIS C 5101-1 As per 4.10 JIS C 5101-3 Repetition : 5 cycles (1 cycle : steps 1 to 4) without discontinuation. As per 4.22 JIS C 5101-1 As per 4.12 JIS C 5101-3 After leaving the sample under such atmospheric Less than initial limit condition that the temperature and humidity are TCA0G686M8R : Within 15% of initial value 602C and 90 to 95% RH,respectiveiy, for 50012h TCA0G107M8R : Within 20% of initial value leave it at room : Within 10% of initial value temperature for over 24h and then measure the Others sample. TCA0G686M8R : Less than 150% of initial limit TCA0G107M8R : Less than 150% of initial limit Others : Less than initial limit www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. 3/7 2012.02 - Rev.G TC Series A Case Data Sheet Performance Item Temperature Stability Temp. -55C C / C Within 0/-12% of initial value Df (tan ) Shall be satisfied the voltage on " Standard list " Temp. +85C C / C TCA0G686M8R : Within +12/0% of initial value TCA0G107M8R : Within +12/0% of initial value Others : Within +10/0% of initial value Df (tan ) Shall be satisfied the voltage on " Standard list " L.C. Less than 1000% of initial limit Temp. +125C C / C Within +15/0% of initial value Df (tan ) Shall be satisfied the voltage on " Standard list " L.C. Less than 1250% of initial limit Appearance As per 4.26JIS C 5101-1 As per 4.14JIS C 5101-3 Shall be satisfied the voltage on " Standard list " Apply the specified surge voltage via the serial resistance of 1k every 50.5 min. TCA0G686M8R : Within 15% of initial value for 305 s. each time in the atmospheric condition of 852C. TCA0G107M8R : Within 20% of initial value Repeat this procedure 1,000 times. Others : 10% of initial value After the specimens, leave it at room temperature for over 24h and then measure the sample. Less than initial limit L.C. C / C Df (tan ) Appearance Loading at High temperature L.C. Terminal strength As per 4.29 JIS C 5101-1 As per 4.13 JIS C 5101-3 - L.C. Surge voltage Test conditions (based on JIS C 5101-1 and JIS C 5101- 3) There should be no significant abnormality. There should be no significant abnormality. TCA0G686M8R : Less than 125% of initial limit TCA0G107M8R : Less than 125% of initial limit TCA1A226M8R : Less than 125% of initial limit TCA1E105M8R : Less than 125% of initial limit Others : Less than initial limit C / C TCA0G686M8R : Within 15% of initial value TCA0G107M8R : Within 20% of initial value TCA0J476M8R : Within 15% of initial value TCA1A226M8R : Within 15% of initial value Others : Within10% of initial value Df (tan ) Less than initial limit Capacitance The measured value should be stable. Appearance There should be no significant abnormality. As per 4.23 JIS C 5101-1 As per 4.15 JIS C 5101-3 After applying the rated voltage for 2000+72/0 h without discontinuation via the serial resistance of 3 or less at a temperature of 852C, leave the sample at room temperature / humidity for over 24h and measure the value. As per 4.35 JIS C 5101-1 As per 4.9 JIS C 5101-3 A force is applied to the terminal until it bends to 1mm and by a prescribed tool maintain the condition for 5s. (See the figure below) (Unit : mm) 50 20 F (Apply force) R230 1 thickness=1.6mm 45 www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. 4/7 45 2012.02 - Rev.G TC Series A Case Item Adhesiveness Data Sheet Performance The terminal should not come off. Test conditions (JIS C 5101-1 and JIS C 5101- 3) As per 4.34 JIS C 5101-1 As per 4.8 JIS C 5101-3 Apply force of 5N in the two directions shown in the figure below for 101s after mounting the terminal on a circuit board. product ja Apply force a circuit board Dimensions Refer to "External dimensions" Measure using a caliper of JIS B 7507 Class 2 or higher grade. Resistance to solvents The indication should be clear As per 4.32 JIS C 5101-1 As per 4.18 JIS C 5101-3 Dip in the isopropyl alcohol for 305s, at room temperature. Solderability 3/4 or more surface area of the solder coated terminal dipped in the soldering bath should be covered with the new solder. As per 4.15.2 JIS C 5101-1 As per 4.7 JIS C 5101-3 Dip speed=252.5mm / s Pre-treatment(accelerated aging): Leave the sample on the boiling distilled water for 1 h. Solder temp. : 2455C Duration : 30.5s Solder : M705 Flux : Rosin 25% IPA 75% Vibration Capacitance Measure value should not fluctuate during the measurement. Appearance There should be no significant abnormality. www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. As per 4.17 JIS C 5101-1 Frequency : 10 to 55 to 10Hz/min. Amplitude : 1.5mm Time : 2h each in X and Y directions Mounting : The terminal is soldered on a print circuit board. 5/7 2012.02 - Rev.G TC Series A Case Data Sheet Standard products list, TC series A case Df Impedance Leakage 120Hz 100kHz Tolerance current (%) 25C 1WV.60s (%) 25C 125C -55C () (A) 85C Rated voltage 85C Category voltage 125C Surge voltage 85C (V) (V) (V) TC A 0G 475M8R 4 2.5 5 4.7 + - 20 0.5 10 6 8 5.6 TC A 0G 685M8R 4 2.5 5 6.8 + - 20 0.5 12 8 10 4.9 TC A 0G 106M8R 4 2.5 5 10 + - 20 0.5 12 8 10 4.2 Part No. Cap. 120Hz (F) TC A 0G 156M8R 4 2.5 5 15 + - 20 0.6 12 8 10 4 TC A 0G 226M8R 4 2.5 5 22 + - 20 0.9 12 8 10 3 TC A 0G 336M8R 4 2.5 5 33 + - 20 1.3 14 10 12 3.5 TC A 0G 476M8R 4 2.5 5 47 + - 20 1.9 30 12 16 3.2 TC A 0G 686M8R 4 2.5 5 68 + - 20 2.7 34 18 24 3 TC A 0G 107M8R 4 2.5 5 100 + - 20 4 54 30 36 3 TC A 0J 335M8R 6.3 4 8 3.3 + - 20 0.5 10 6 8 5.6 TC A 0J 475M8R 6.3 4 8 4.7 + - 20 0.5 12 8 10 4.9 TC A 0J 685M8R 6.3 4 8 6.8 + - 20 0.5 12 8 10 4.2 TC A 0J 106M8R 6.3 4 8 10 + - 20 0.6 12 8 10 4 TC A 0J 156M8R 6.3 4 8 15 + - 20 0.9 12 8 10 3 TC A 0J 226M8R 6.3 4 8 22 + - 20 1.4 14 10 12 3.5 TC A 0J 336M8R 6.3 4 8 33 + - 20 2.1 30 12 16 3.2 TC A 0J 476M8R 6.3 4 8 47 3.0 34 18 24 3.2 TC A 1A 155M8R 10 6.3 13 1.5 + - 20 + - 20 0.5 10 6 8 8.8 TC A 1A 225M8R 10 6.3 13 2.2 + - 20 0.5 10 6 8 5.6 0.5 12 8 10 4.9 0.5 12 8 10 4.2 TC A 1A 335M8R 10 6.3 13 3.3 + - 20 TC A 1A 475M8R 10 6.3 13 4.7 + - 20 TC A 1A 685M8R 10 6.3 13 6.8 + - 20 0.7 12 8 10 4 TC A 1A 106M8R 10 6.3 13 10 + - 20 1.0 12 8 10 3 TC A 1A 156M8R 10 6.3 13 15 + - 20 1.5 14 10 12 3.5 TC A 1A 226M8R 10 6.3 13 22 + - 20 2.2 30 12 16 3.2 TC A 1C 105M8R 16 10 20 1 + - 20 0.5 10 6 8 7 TC A 1C 155M8R 16 10 20 1.5 + - 20 0.5 10 6 8 5.6 TC A 1C 225M8R 16 10 20 2.2 + - 20 0.5 10 6 8 4.9 TC A 1C 335M8R 16 10 20 3.3 + - 20 0.5 10 6 8 4.8 TC A 1C 475M8R 16 10 20 4.7 + - 20 0.8 10 6 8 3.9 TC A 1C 685M8R 16 10 20 6.8 + - 20 1.1 10 6 8 3.8 1.6 12 8 10 3.5 0.5 10 6 8 7 TC A 1C 106M8R 16 10 20 10 TC A 1D 105M8R 20 13 26 1 + - 20 + - 20 TC A 1D 155M8R 20 13 26 1.5 + - 20 0.5 10 6 8 6 TC A 1D 225M8R 20 13 26 2.2 + - 20 0.5 10 6 8 5.2 TC A 1D 335M8R 20 13 26 3.3 + - 20 0.7 10 6 8 4.8 TC A 1D 475M8R 20 13 26 4.7 + - 20 0.9 10 6 8 3.9 TC A 1E 105M8R 25 16 32 1 + - 20 0.5 10 6 8 7 0.5 10 6 8 6 0.6 10 6 8 5.2 TC A 1E 155M8R 25 16 32 1.5 + - 20 TC A 1E 225M8R 25 16 32 2.2 + - 20 TC A 1E 335M8R 25 16 32 3.3 + - 20 0.8 10 6 8 4.8 TC A 1E 475M8R 25 16 32 4.7 + - 20 1.2 12 8 10 3.4 TC A 1V 105M8R 35 22 44 1 + - 20 0.5 10 6 8 7 =Under development www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. 6/7 2012.02 - Rev.G TC Series A Case Data Sheet Packaging specifications Case code A+ -0.1 B+ -0.1 t1+ - 0.05 t2 + - 0.1 A 1.9 3.5 0.25 1.9 +0.1 -0 3.50.05 A B 4.00.1 t1 8.00.2 1.5 1.750.1 Taping [A case] Chip 4.00.1 t2 2.00.05 Feeding direction Packaging style Case code Packaging A case Taping Packaging style plastic taping Symbol Basic ordering units 180mm Reel 8R 2,000pcs 60 +1 0 0 180-1.5 11.4+ -1.0 13+ -0.2 +1.0 9.0 0 Reel [A case] Pull direction Label sticking position www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. EIAJ ET-7200A 7/7 2012.02 - Rev.G Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. R1120A