1/7
www.rohm.com
○
c 2012 ROHM Co., Ltd. All rights reserved. 2012.02 - Rev.G
Chip tantalum capacitors
TC Series A Case
Features (A) Dimensions (Unit : mm)
1) Vital for all hybrid integrated circuits
board application.
2) Wide capacitance range.
3) Screening by thermal shock.
Part No. Explanation
M0 J 8 RT 1 0 6C A
Rated voltage Capacitance tolerance
Nominal capacitance in pF in 3 digits:
2 significant figures followed by the figure
representing the number of 0's.
8 :
Reel width : 8mm
R :
Positive electrode on the side opposite to sprocket ho
le
1
6
13 64
2 5
11 Series name
TC
2
Case style
3
4
Nominal capacitance
5
Taping
20%
M : +
−
4
CODE 6.3
0J 10
1A 16
1C 20 35
1D 1V
25
1E
Rated voltage (V) 0G
A
Dimensions
L
H
S
W
2
W
1
SS
W
H
LW
Anode mark
2
1
(Unit : mm)
3.2 0.2
+
−
1.6 0.2
+
−
1.2 0.2
+
−
1.6 0.2
+
−
0.8 0.3
+
−
A case
+−
2/7
www.rohm.com
○
c 2012 ROHM Co., Ltd. All rights reserved. 2012.02 - Rev.G
Data Sheet TC Series A Case
Rated table
(μF)
Rated voltage (V.DC)
4
1.0 (105) A
1.5 (155) A
2.2 (225) A
3.3 (335) A
A
A
A
A
A
A
A
A
4.7 (475) A
6.8 (685) A
A
A
A
A10 (106) A
A
A
A
A
A
A
A
A
AA
A
A
15 (156) A
22 (226) A A
A
A
33 (336)
47 (476)
68 (686)
100 (107)
150 (157)
A
A
A
A
6.3 10 16 20 25
Remark) Case size codes (A) in the above show products line-up.
∗
Under development
AA
A
35
∗
Marking
The indications listed below should be given on the surface of a capacitor.
(1) Polarity
: The polarity should be shown by bar. (on the anode side)
(2) Rated DC voltage : Due to the small size of A case, a voltage code is used as shown belo
w.
(3) Visual typical example (1) voltage code (2) capacitance code
Voltage
Code Rated DC
Voltage (V)
g
j
A
C
D
V
4
6.3
10
16
20
35
E25
Capacitance
Code
Nominal
Capacitance (μF)
A
E
J
N
S
W
a
e
j
n
1.0
1.5
2.2
3.3
4.7
6.8
10
15
22
33
s47
w68
100
[
A case] note 1)
note 2) voltage code and capacitance code are variable with parts number
−
(1)
j
−
(2)
a
a
j a
j a
manufacture code
3/7
www.rohm.com
○
c 2012 ROHM Co., Ltd. All rights reserved. 2012.02 - Rev.G
Data Sheet TC Series A Case
Characteristics
Item Performance Test conditions (based on JIS C 5101−1 and JIS C 5101−3)
Operating Temperature −55°C~+125°C
Maximum operating
temperature with no voltage
derating
+85°C
Rated voltage (VDC) 20 2516106.34
Category voltage (VDC) 13 16106.342.5
Surge voltage (VDC) 13852620 32
DC Leakage current 0.5μA or 0.01CV whichever is greater
Shown in " Standard list "
Capacitance tolerance
Measuring frequency : 100
±
10kHz
Measuring voltage : 0.5Vrms or less
Measuring circuit
: DC Equivalent series circuit
Tangent of loss angle
(Df, tan δ)
Impedance
Resistance to
Soldering heat
Temperature
cycle
Moisture
resistance
There should be no significant abnormality.
The indications should be clear.
Appearance
ΔC / C
Df (tan δ)
L.C.
Shall be satisfied the voltage on
" Standard list "
Measuring frequency : 120
±
12Hz
Measuring voltage : 0.5Vrms +1.5 to 2V.DC
Measuring circuit
: DC Equivalent series circuit
Shall be satisfied the voltage on
" Standard list "
at 85°C
at 125°C
at 85°C
Voltage : Rated voltage for 1min
Shall be satisfied allowance range.
±
20% Measuring frequency : 120
±
12Hz
Measuring voltage : 0.5Vrms +1.5 to 2V.DC
Measuring circuit
: DC Equivalent series circuit
Less than initial limit
Voltage reduction when temperature exceeds +
85
°C
35
22
44
As per 4.9 JIS C 5101-1
As per 4.5.1 JIS C 5101-3
As per 4.7 JIS C 5101-1
As per 4.5.2 JIS C 5101-3
As per 4.8 JIS C 5101-1
As per 4.5.3 JIS C 5101-3
As per 4.10 JIS C 5101-1
As per 4.5.4 JIS C 5101-3
As per 4.14 JIS C 5101-1
As per 4.6 JIS C 5101-3
Dip in the solder bath
Solder temp : 260
±
10°C
Duration
:
5
±
0.5s
Repetition
: 1
After the specimens, leave it at room temperature for
over 24h and then measure the sample.
As per 4.16 JIS C 5101-1
As per 4.10 JIS C 5101-3
As per 4.22 JIS C 5101-1
As per 4.12 JIS C 5101-3
Others
:
Within
±
5% of initial value
There should be no significant abnormality.
The indications should be clear.
Appearance
ΔC / C
Df (tan δ)
L.C. Less than initial limit
After leaving the sample under such atmospheric
condition that the temperature and humidity are
60±2°C and 90 to 95% RH,respectiveiy, for 500±12h
leave it at room
temperature for over 24h and then measure the
sample.
TCA0G686M8R
:
Within
±15%
of initial value
TCA0G107M8R
:
Within
±20%
of initial value
Others
:
Within
±10%
of initial value
Others
:
Within
±10%
of initial value
Others
: Less than initial limit
There should be no significant abnormality.
The indications should be clear.
Appearance
ΔC / C
Df (tan δ)
L.C.
Less than initial limit
Repetition : 5 cycles
(1 cycle : steps 1 to 4) without discontinuation.
Less than initial limit
TCA0G686M8R
:
Within
±15%
of initial value
Temp. Time
1
2
3
4
Room temp.
Room temp.
3min.or less
3min.or less
30±3min.
30±3min.
−55 3°C
+
−
125 2°C
+
−
TCA0G686M8R : Within
±
15% of initial value
TCA0G107M8R : Within
±
20% of initial value
TCA0G107M8R
:
Within
±20%
of initial value
TCA0J476M8R
:
Within
±15%
of initial value
TCA0G686M8R : Less than 150% of initial limit
TCA0G107M8R : Less than 150% of initial limit
After the specimens, leave it at room temperature for
over 24h and then measure the sample.
TCA1A226M8R
:
Within
±15%
of initial value
TCAP0J226
: Less than 150%
of initial limit
Others
:
Less than initial limit
4/7
www.rohm.com
○
c 2012 ROHM Co., Ltd. All rights reserved. 2012.02 - Rev.G
Data Sheet TC Series A Case
Item Performance Test conditions (based on JIS C 5101−1 and JIS C 5101− 3)
Temperature
Stability
Surge voltage
Shall be satisfied the voltage on " Standard list "
As per 4.29 JIS C 5101-1
As per 4.13 JIS C 5101-3
As per 4.23 JIS C 5101-1
As per 4.15 JIS C 5101-3
As per 4.35 JIS C 5101-1
As per 4.9 JIS C 5101-3
Temp.
Appearance There should be no significant abnormality.
Temp.
−55
°C
+85
°C
Df (tan δ)
L.C.
L.C.
Less than 1000% of initial limit
Shall be satisfied the voltage on " Standard list "
Df (tan δ)
Shall be satisfied the voltage on " Standard list "
Df (tan δ)
L.C.
Less than 1250% of initial limit
Temp.
+125
°C
ΔC / C
Within 0/−12% of initial value
ΔC / C
Within +15/0% of initial value
ΔC / C
Others
: Within +10/0% of initial value
−
Loading at
High temperature
ΔC / C
Df (tan δ)
L.C.
L.C.
Shall be satisfied the voltage on " Standard list "
Less than initial limit
After applying the rated voltage for 2000+72/0 h without
discontinuation via the serial resistance of 3Ω or less
at a temperature of
85±2°C
, leave the sample at room
temperature / humidity for over 24h and measure the value.
As per 4.26JIS C 5101-1
As per 4.14JIS C 5101-3
Apply the specified surge voltage via the serial resistance of
1kΩ every 5±0.5 min.
for 30±5 s. each time in the atmospheric condition of 85±2°C.
Repeat this procedure 1,000 times.
After the specimens, leave it at room temperature for
over 24h and then measure the sample.
Df (tan δ)Less than initial limit
Others
: ±10% of initial value
ΔC / C TCA0G686M8R
: Within ±15% of initial value
TCA0G107M8R
: Within ±20% of initial value
TCA0J476M8R
: Within ±15% of initial value
There should be no significant abnormality.
Appearance
There should be no significant abnormality.
Appearance
Terminal
strength
The measured value should be stable.
A force is applied to the terminal until it bends to 1mm and
by a prescribed tool maintain the condition for 5s.
(See the figure below)
Capacitance
1
F (Apply force)
(Unit : mm)
20
50
R230
45 45
thickness=1.6mm
TCA0G686M8R : Within +12/0% of initial value
TCA0G107M8R : Within +12/0% of initial value
TCA0G686M8R
: Within ±15% of initial value
TCA0G686M8R : Less than 125% of initial limit
TCA0G107M8R : Less than 125% of initial limit
TCA1A226M8R : Less than 125% of initial limit
TCA1E105M8R : Less than 125% of initial limit
TCA1A226M8R
: Within ±15% of initial value
TCA0G107M8R
: Within ±20% of initial value
Others
: Within±10% of initial value
Others
: Less than initial limit
5/7
www.rohm.com
○
c 2012 ROHM Co., Ltd. All rights reserved. 2012.02 - Rev.G
Data Sheet TC Series A Case
Item Performance Test conditions (JIS C 5101−1 and JIS C 5101− 3)
Adhesiveness
Dimensions
The terminal should not come off. As per 4.34 JIS C 5101-1
As per 4.8 JIS C 5101-3
Apply force of 5N in the two directions shown in the figure
below for 10±1s after mounting the terminal on a circuit board.
Apply force
a circuit board
product
ja
Refer to "External dimensions" Measure using a caliper of JIS B 7507 Class 2
or higher grade.
Resistance to solvents The indication should be clear As per 4.32 JIS C 5101-1
As per 4.18 JIS C 5101-3
Dip in the isopropyl alcohol for 30
±
5s, at room
temperature.
Solderability 3/4 or more surface area of the solder coated
terminal dipped in the soldering bath should
be covered with the new solder.
As per 4.15.2 JIS C 5101-1
As per 4.7 JIS C 5101-3
Dip speed=25±2.5mm / s
Pre−treatment(accelerated aging): Leave
the sample on the boiling distilled water for 1 h.
Solder temp. : 245±5°C
Duration
: 3±0.5s
Solder : M705
Flux
: Rosin 25% IPA 75%
Capacitance
Vibration
Appearance
Measure value should not fluctuate during the
measurement.
There should be no significant abnormality.
As per 4.17 JIS C 5101-1
Frequency : 10 to 55 to 10Hz/min.
Amplitude : 1.5mm
Time : 2h each in X and Y directions
Mounting : The terminal is soldered on a print circuit board
.
6/7
www.rohm.com
○
c 2012 ROHM Co., Ltd. All rights reserved. 2012.02 - Rev.G
Data Sheet TC Series A Case
Standard products list, TC series A case
22 0.9
33 1.3
47
68
1.9
2.7
0.5
3.3
1.5
4
10
0.5
0.5
0.5
15 0.6
TC A 0G 475M8R
TC A 0G 106M8R
TC A 0G 156M8R
TC A 0G 226M8R
TC A 0G 336M8R
TC A 0G 476M8R
TC A 0G 686M8R
TC A 0J 335M8R
4.7
TC A 0G 685M8R 6.8
TC A 0J 475M8R 4.7
2.2
TC A 0J 685M8R
TC A 0J 106M8R
2.5 5
4 2.5 5
4 2.5 5
4 2.5 5
4 2.5 5
4 2.5 5
4 2.5 5
4 2.5 5
6.3 4 8
6.3 4 8
6.3 4 8
6.3 4 8
6.3 4 8
6.3 4 8
6.3 4 8
6.3 4 8
10 6.3 13
10 6.3 13
10 6.3 13
10 6.3 13
10 6.3 13
10 6.3 13
10 6.3 13
10 6.3 13
16 10 20
16 10 20
16 10 20
6.8
3.3
10
4.7
0.5
15TC A 0J 156M8R
TC A 0J 226M8R 22
3.0
0.7
TC A 0J 336M8R
TC A 0J 476M8R
TC A 1A 155M8R
TC A 1A 225M8R
TC A 1A 335M8R
TC A 1A 475M8R
TC A 1A 685M8R
33 2.1
0.9
47
6.8
10 6
10
12
18
6
10
12
18
14
30
34
10
14
30
34
8
812 10
812 10
812 10
812 10
12
16
24
8
812 10
0.5 812 10
812 10
812 10
12
16
24
0.5 610 8
0.5 610 8
0.5 812 10
0.5
4
3
3.5
3.2
3
5.6
4.9
5.6
4.9
4.2
3.5
3.2
3.2
8.8
5.6
4.9
812 10 4.2
812 10 4
812 10 3
1014 12 3.5
1230 16 3.2
4.2
4
3
20
+
−
20
+
−
20
+
−
20
+
−
20
+
−
20
+
−
20
+
−
100 4TC A 0G 107M8R 4 2.5 5 3054 36 320
+
−
20
+
−
20
+
−
20
+
−
20
+
−
20
+
−
20
+
−
20
+
−
20
+
−
20
+
−
20
+
−
20
+
−
20
+
−
20
+
−
20
+
−
20
+
−
20
+
−
20
+
−
20
+
−
1.0
TC A 1A 106M8R 10
1.5
TC A 1A 156M8R 15
2.2
610 8 70.5
610 8 5.60.5
20
+
−
20
+
−
20
+
−
20
+
−
20
+
−
610 8 4.90.5
610 8 4.8
610 8 3.9
610 8 3.8
812 10 3.5
0.5
TC A 1A 226M8R 22
TC A 1C 105M8R 1
TC A 1C 155M8R 1.5
TC A 1C 225M8R 2.2
TC A 1C 335M8R 3.310 2016
10 2016
10 2016
10 2016
0.8
TC A 1C 475M8R 4.7
1.1TC A 1C 685M8R 6.8
1.6TC A 1C 106M8R 10
0.6
1.4
20
+
−610 8 716 3225 0.5TC A 1E 105M8R 1
20
+
−610 8 613 2620 0.5TC A 1D 155M8R 1.5
20
+
−610 8 5.216 3225 0.6
TC A 1E 225M8R 2.2
20
+
−610 8 5.213 2620 0.5TC A 1D 225M8R 2.2
20
+
−610 8 4.813 2620 0.7TC A 1D 335M8R 3.3
20
+
−610 8 3.913 2620 0.9TC A 1D 475M8R 4.7
20
+
−610 8 713 2620 0.5TC A 1D 105M8R 1
20
+
−610 8 616 3225 0.5TC A 1E 155M8R 1.5
20
+
−812 10 3.416 3225 1.2TC A 1E 475M8R 4.7
20
+
−610 8 722 4435 0.5TC A 1V 105M8R 1
20
+
−610 8 4.816 3225 0.8TC A 1E 335M8R 3.3
∗
∗
20
+
−
=Under development
Part No.
Rated
voltage
85°C
(V)
Category
voltage
125°C
(V)
Surge
voltage
85°C
(V)
Cap.
120Hz
(μF)
Tolerance
(%)
Leakage
current
25°C
1WV.60s
(μA)
Df
120Hz
(%)
−55°C125°C
25°C
85°C
Impedance
100kHz
(Ω)
7/7
www.rohm.com
○
c 2012 ROHM Co., Ltd. All rights reserved. 2012.02 - Rev.G
Data Sheet TC Series A Case
Packaging specifications
Taping [A case]
Case code
A
A 0.1
+
−B 0.1
+
−t
1
0.05
+
−t
2
0.1
+
−
1.9 3.5 0.25 1.9
Feeding direction
2.0
±
0.05
4.0
±
0.1 4.0
±
0.1
A
B
8.0
±
0.2
3.5
±
0.05
1.75
±
0.1
Chip
φ1.5
+0.1
−0
t
2
t
1
Packaging style
2,000pcs
Case code Packaging
Taping
A case
Packaging style
plastic taping φ180mm Reel
Symbol
8R
Basic ordering unit
s
Reel [A case]
φ13 0.2
φ60 +1
0
0
−1.5
φ180
9.0
11.4 1.0
Label sticking position EIAJ ET−7200A
Pull direction
+
−+1.0
0
+
−
R1120A
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
Notice
ROHM Customer Support System
http://www.rohm.com/contact/
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
Notes
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specied herein is subject to change for improvement without notice.
The content specied herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specied in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specied herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specied in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, ofce-automation equipment, commu-
nication devices, electronic appliances and amusement devices).
The Products specied in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, re or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, re control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-
controller or other safety device). ROHM shall bear no responsibility in any way for use of any
of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specied herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.