PRODUCT SELECTION GUIDE 2009 SMD RESISTORS + MLCC SMD CERAMIC EMI FILTER CAPACITORS - X2Y (R) HIGH FREQUENCY PRODUCTS www.yageo.com MULTILAYER CHIP VARISTORS 2 Preface Part numbering system and ordering You can order components from this catalogue in two ways. Both ways give logistic and packing information. * Clear text ordering code This unique number is an easily-readable code. - 15 digits code (PHYCOMP CTC ) -14 to 17 digits code (GLOBAL PART NUMBER for both Yageo and Phycomp branded products) * 12 digits ordering code This unique 12NC number forms the basis of the Phycomp logistic system. Please note that 12 digits ordering code will expire at the end of 2010. You will find details for ordering in the "Ordering" section next to each selection chart. Minimum shipment quantities, prices and delivering details can be obtained from the Yageo sales organization in your country or from one of our franchised distributors. Case size codes Throughout this catalogue, inch-based codes are used for the component sizes. According to IEC 60384-10, amendment 2 of September 2000 for MLCCs, and IEC 60115-8, amendment 1 of July 2000 for R-chip. Values for length and width should be in millimeters rather than in inches. To distinguish between inch-based codes and metric-based codes, metric-based codes will temporarily have the suffix `'M''. The table right next shows the relation between inch-based case sizes versus the recommended metric case size designators. Please note that HF products use metric case size only. Case size designation and cross-reference Inch-based Metric Inch-based Metric Inch-based Metric 01005 0402M 0606 1616M 1224 3250M 0201 0603M 0612 1632M 1225 3264M 0202 0605M 0616 1640M 1812 4532M 0402 1005M 0805 2012M 2007 5320M 0404 1010M 1008 2520M 2010 5025M 0408 1020M 1206 3216M 2220 5750M 0508 1220M 1210 3225M 2512 6432M 0603 1608M 1218 3245M 3014 7836M Contact us Founded in 1977, the Yageo Corporation has become a world-class provider of passive-component services with capabilities on a global scale, including production and sales facilities in Asia, Europe and America. The corporation is uniquely positioned to provide one-stop-shopping, offering its complete product portfolio of resistors, capacitors and inductors in both commodity and specialty versions, plus design-in capability, distribution, e-commerce connection and logistics. Yageo markets its products under the product brand names Yageo, Phycomp and Vitrohm. All products can be obtained from our Yageo sales offices, of which contact details can be found on the backcover of this catalogue. For most up-to-date information, as well as contact details of our franchise distributors, please refer to our website: www.yageo.com 3 Table of Contents Resistor Chip General Information 8 Specification overview Ordering Information - Global part number 10 Ordering information for North America 12 IEC publication 63, SPQ, last digit of 12NC 13 Resistor Chip Selection Charts 14 Thick film resistor chips 14 Introduction to thick film genaral purpose and double power resistors 14 01005 to 0805 16 1206 to 2512 18 Thin film resistor chips 20 Introduction to thin film chip resistors 20 High precision - High stability, 0402 / 0603 22 High precision - High stability, 0805 to 1210 24 High precision - High stability, 2010 / 2512 26 General Purpose, 0402 to 2512 28 Thick film Array / Network resistor chips 30 Introduction to thick film array / network resistors 30 Arrays, convex and concave 32 Networks, T-type and L-type 34 Thin film Array / Multi-value resistor chips (convex type) 36 Introduction to thin film array chip resistors 36 Low ohmic resistor chips 38 Introduction to low ohmic / low ohmic high power chip resistors 38 Low ohmic, 0201 to 1206 40 Low ohmic, 1210 to 2512 42 Low ohmic, high power, 0805 / 1206 44 High ohmic resistor chips 46 Introduction to high ohmic chip resistors 46 Resistor chips with Ni/Au terminations 48 Introduction to Ni/Au terminations chip resistors 48 0402 to 1206 50 Surge resistor chips 52 Introduction to Surge chip resistors 52 0805 to 2512 54 High voltage resistor chips 56 Introduction to high voltage chip resistors 56 0805 to 2512 58 Trimmable resistor chips 60 Introduction to trimmable chip resistors 60 0402 to 1206 62 Current sensors - Low TCR resistor chips (standard / power enhancement) 64 Introduction to current sensors - low TCR chip resistors 64 Standard type, PR2010 / PR2512 / PF2512 / PT0402 to 2512 66 RF attenuators chip resistors 68 Introduction to RF attenuator chip resistors 68 0404 70 Resistor Chip Engineering Design Kits 71 Engineering design kits 4 8 71 Table of Contents MLCC General Information 74 Specification overview 74 Case dimensions 75 Ordering Information - Global part number 76 Ordering information for North America 77 Thickness classes and packing quantities for all series 78 MLCC Selection Charts 79 NP0 79 NP0 - General purpose 16 to 25V, 0201 to 0603 79 NP0 - General purpose 16 to 25V, 0805 to 1210 80 NP0 - Gerneral purpose 50V, 0201 to 1812 82 NP0 - Midium voltage, 0603 / 0805 85 NP0 - Midium voltage, 1206 / 1210 86 NP0 - Midium voltage, 1808 / 1812 87 NP0 - High voltage, 1206 / 1210 88 NP0 - High voltage, 1808 / 1812 89 NP0 - High frequency, 0402 / 0603 91 NP0 - Microwave, 0603 to 1206 93 X7R 95 X7R - General purpose, 0201 / 0402 95 X7R - General purpose & High capacitance, 0603 / 0805 96 X7R - Gerneral purpose & High capacitance, 1206 to 1812 97 X7R - Midium voltage, 0603 / 0805 98 X7R - Midium voltage, 1206 / 1210 99 X7R - Midium voltage, 1808 / 1812 100 X7R - High voltage, 1206 / 1210 101 X7R - High voltage, 1808 / 1812 102 X7R - Low inductance, 0306 to 0612 104 X5R 106 X5R - General purpose & High capacitance, 0201 / 0402 106 X5R - General purpose & High capacitance, 0603 / 0805 107 X5R - High capacitance, 1206 to 1812 108 Y5V 110 Y5V - General purpose & High capacitance, 0201 / 0402 110 Y5V - General purpose & High capacitance, 0603 / 0805 111 Y5V - General purpose & High capacitance, 1206 / 1210 112 Safety certification MLCCs 114 NP0 - High voltage SC type, 1808 / 1812 114 X7R - High voltage SC type, 1808 / 1812 115 Arrays 117 X7R - 2C Arrays, 0405 117 NP0 - 4C Arrays, 0508 / 0612 119 X7R - 4C Arrays, 0508 / 0612 120 Y5V - 4C Arrays, 0508 / 0612 121 MLCC Engineering Design Kits 123 Sample kits for 0201 / 0402 123 Sample kits for 0603 / 0805 124 Sample kits for 1206 125 Sample kits for high capacitance series 126 5 Table of Contents High voltage sample kits for PCs segment 127 High voltage sample kits for inverter segment 128 High voltage sample kits for general application 129 High voltage sample kits for safety certification MLCCs 130 Sample kits for high frequency series 131 Sample kits for all sizes, all types, E1 series only 132 HF Product Selection Charts 134 GPS patch antenna and active module 134 UHF, Dual-band and Triple-band antenna 135 Bluetooth antenna 136 Band pass filter and Low pass filter 137 Balun and Combo 138 Diplexer 139 X2Y(R) Product Selection Charts 142 SMD Ceramic EMI Filter Capacitors X2Y(R) series 142 Ordering information 143 MLV Product Selection Charts 6 146 Case dimensions and specification for 0402 146 Specification for 0603 to 1206 147 Ordering information for 0402 to 1206 148 SURFACE-MOUNT RESISTOR CHIPS Resistor Chip General Information Specification overview Power Max. Operating rating voltage Temp. range Global part number Series Size ! RC0100xR-07xxxxL 01005 1/32W 15V -55C to 125C Resistance range Tolerance 10 R 1M 5% 1 R 10M Max.: 1M Max.: 10M T. C. R. 10 R 1M 250 ppm/C 1% 5% 1 R 10 -100/+350 ppm/C 10< R 10M 200 ppm/C RC0201xR-07xxxxL 0201 1/20W 25V -55C to 125C RC0402xR-07xxxxL RC0603xR-07xxxxL RC0805xR-07xxxxL RC1206xR-07xxxxL RC1210xR-07xxxxL RC1218xK-07xxxxL RC2010xK-07xxxxL RC2512xK-07xxxxL ! RC0805xR-7WxxxxL ! RC1206xR-7WxxxxL ! RC2512xK-7WxxxxL ! RC0805xR-07xxxxL ! RC1206xR-07xxxxL ! YC102-xR-07xxxxL YC122-xR-07xxxxL YC124-xR-07xxxxL ! YC162-xR-07xxxxL YC164-xR-07xxxxL YC248-xR-07xxxxL YC324-xR-07xxxxL ! TC122-xR-07xxxxL ! TC124-xR-07xxxxL TC164-xR-07xxxxL 0402 0603 0805 1206 1210 1218 2010 2512 0805 1206 2512 0805 1206 2*0201 2*0402 4*0402 2*0603 4*0603 8*0602 4*1206 2*0402 4*0402 4*0603 1/16W 1/10W 1/8W 1/4W 1/2W 1W 3/4W 1W 1/4W 1/2W 2W 1/8W 1/4W 1/32W 1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 1/16W 1/16W 1/16W 50V 50V 150V 200V 200V 200V 200V 200V 150V 200V 200V 150V 200V 15V 50V 50V 50V 50V 50V 200V 25V 50V 50V -55C to 155C 1 R 22M -55C to 155C 1 R 22M 1 R 10 -55C to 155C 1 R 22M 200 ppm/C Max./Min.: 1M/10 0.5% 10M< R 22M -55C to 155C 1 R 22M Max.: 10M 1% 10< R 10M 100 ppm/C -55C to 155C 1 R 22M Max.: 22M 5% -55C to 155C 1 R 1M -55C to 155C 1 R 22M -55C to 155C 1 R 22M -55C to 155C 1 R 100 1% -55C to 155C 1 R 100 200 ppm/C 5% -55C to 155C 1 R 150 -55C to 155C 24M R 100M 5%, 10%, 20% 300 ppm/C -55C to 155C 24M R 100M -55C to 125C 10 R 1M Min.: 10 1% -55C to 125C 1 R 1M Min.: 1 5% -55C to 155C 10 R 1M -55C to 155C 10 R 1M 5% -55C to 155C 1 R 1M 200 ppm/C 1% -55C to 155C 10 R 1M 5% -55C to 155C 10 R 1M -55C to 125C 10 R 1M Min.: 10 1% -55C to 125C 10 R 1M Min.: 1 5% -55C to 155C 1 R 1M RC YC TC YC158TJR-07xxxxL YC158 10P8R 1/16W (0612) 25V -55C to 155C 10 R 100K 5% 10 R 100K 200 ppm/C YC358xJK-07xxxxL YC358 10P8R 1/16W (1225) 50V -55C to 155C 10 R 330K 5% 10 R 330K 200 ppm/C (PxR)^1/2 (PxR)^1/2 (PxR)^1/2 (PxR)^1/2 (PxR)^1/2 (PxR)^1/2 (PxR)^1/2 (PxR)^1/2 (PxR)^1/2 (PxR)^1/2 -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C 0.05 R <1 RL0402xR-07xxxxL RL0603xR-07xxxxL RL0805xR-07xxxxL RL1206xR-07xxxxL RL1210xR-07xxxxL RL1218xK-07xxxxL RL2010xK-07xxxxL RL2512xK-07xxxxL ! RL0805xR-7WxxxxL ! RL1206xR-7WxxxxL RL 0402 0603 0805 1206 1210 1218 2010 2512 0805 1206 1/16W 1/10W 1/8W 1/4W 1/2W 1W 3/4W 1W 1/4W 1/2W 0.01 R <1 1% 2% 5% See following table "T.C.R.- RL series" 0.01 R <1 Note: " ! " is the symbol for new product T. C. R. - RL series Operating Type Temp. range RL0402 -55C to +125C 8 RL0603 -55C to +125C RL0805 RL1206 RL1210 -55C to +125C -55C to +125C -55C to +125C RL1218 -55C to +125C RL2010 RL2512 -55C to +125C -55C to +125C Resistance range 50mR<1 10m - 36m 1 500 ppm/C 10m - 18m 10mR<1 1 500 ppm/C 10mR<1 1 500 ppm/C 10mR<1 1 500 ppm/C 10m - 30m 10mR<1 2 000 ppm/C 10m - 18m 10mR<1 1 500 ppm/C 10m R<1 1 500 ppm/C 10mR<1 36m - 91m 1 200 ppm/C 20m - 47m 1 200 ppm/C 1 200 ppm/C 1 000 ppm/C 33m - 56m 1 000 ppm/C 20m - 47m 1 200 ppm/C 1 200 ppm/C T. C. R. 50m - 1 800 ppm/C 91m - 500m 800 ppm/C 51m - 91m 100m - 360m 1 000 ppm/C 600 ppm/C 1 000 ppm/C 600 ppm/C 800 ppm/C 600 ppm/C 60m - 180m 700 ppm/C 51m - 91m 100m - 360m 1 000 ppm/C 600 ppm/C 800 ppm/C 600 ppm/C 500m - 1 300 ppm/C 390m - 500m 510m - 1 300 ppm/C 200 ppm/C 300 ppm/C 200 ppm/C 300 ppm/C 200 ppm/C 200m - 1 250 ppm/C 390m - 500m 510m - 1 300 ppm/C 200 ppm/C 300 ppm/C 200 ppm/C Resistor Chip General Information Specification overview Global part number RT0402xRx07xxxxL RT0603xRx07xxxxL RT0805xRx07xxxxL RT1206xRx07xxxxL RT1210xRx07xxxxL RT2010xKx07xxxxL RT2512xKx07xxxxL RJ0402FRE07xxxxL RJ0603FRE07xxxxL RJ0805FRE07xxxxL RJ1206FRE07xxxxL RJ1210FRE07xxxxL RJ2010FKE07xxxxL RJ2512FKE07xxxxL Series RT RJ Size Power rating Max. voltage 0402 0603 0805 1206 1210 2010 2512 0402 0603 0805 1206 1210 2010 2512 1/16W 1/10W 1/8W 1/8W 1/4W 1/2W 3/4W 1/16W 1/16W 1/10W 1/8W 1/4W 1/2W 3/4W 50V 75V 150V Operating Temp. range -55C to 125C 200V 25V 50V 100V -55C to 125C 150V Resistance range 10 R <121K 5.1 R 681K 5.1 R 1.5M 5.1 R 1.5M 5.1 R 1M 10 R 1M 10 R 1M 10 R 121K 5.1 R 681K 5.1 R 1.5M 5.1 R 1.5M 5.1 R 1M 10 R 1M 10 R 1M Tolerance T. C. R. 0.05% 0.1% 0.25% 0.5% 1% 10 ppm/C 15 ppm/C 25 ppm/C 50 ppm/C 1% 50 ppm/C ! TA164-xR-07xxxxL TA 4*0603 1/16W 75V -55C to 125C 10 R 330K 0.1% 0.5% 1% 25 ppm/C 50 ppm/C ! TD164-xR-07xxxxL TD 4*0603 1/16W 75V -55C to 125C 10 R 330K 0.1% 0.5% 1% 25 ppm/C 50 ppm/C PR2010xKx07xxxxxL PR2010xKx7WxxxxxL PR2512xKx07xxxxxL PR2512xKx7WxxxxxL 2010 PR 2512 PF2512xKx07xxxxxL 2512 0.5W 1W 1W 2W ! PT0402xRx07xxxxL ! PT0603xRx07xxxxL ! PT0805xRx07xxxxL ! PT1206xRx07xxxxL ! PT1210xRx07xxxxL ! PT1218xKx07xxxxL ! PT2010xKx07xxxxL ! PT2512xKx07xxxxL AR0402xR-07xxxxL AR0603xR-07xxxxL AR0805xR-07xxxxL AR1206xR-07xxxxL PT AR RV0805JR-07xxxxL RV1206JR-07xxxxL RV1206FR-07xxxxL RV2512JK-07xxxxL SR0805xR-07xxxxL SR1206xR-07xxxxL SR1218xK-07xxxxL SR2512xK-07xxxxL TR0402xR-07xxxxL TR0603xR-07xxxxL TR0805xR-07xxxxL TR1206xR-07xxxxL ATV321xR-07xxxxL RV SR TR AT 1m R 5m 1W PF PF2512xKx7WxxxxxL 2m R 6m (PxR)^1/2 -55C to 155C (PxR)^1/2 -55C to 155C 2512 2W 0402 0603 0805 1206 1210 1218 2010 2512 0402 0603 0805 1206 1/16W 1/10W 1/8W 1/4W 1/2W 1W 3/4W 1W 1/16W 1/10W 1/8W 1/4W 0805 1/8W 1206 1/4W 2512 0805 1206 1218 2512 0402 0603 0805 1206 1W 1/8W 1/4W 1W 1W 1/16W 1/16W 1/8W 1/4W 0404 40mW 6m R 130m 6m R 130m 1% 2% 5% 1% 2% 5% 2m R 6m 150 ppm/C 1m R 2m 200 ppm/C 2mR <R 100 ppm/C 100 ppm/C 200 ppm/C -55C to 125C 100m R 910m (PxR)^1/2 1% 5% -55C to 155C -55C to 125C -55C to 155C 100 ppm/C 50V 150V 200V 400V 500V -55C to 155C 1 R 10M 1% 5% 1 R 10 200 ppm/C 10< R 10M 100 ppm/C -55C to 155C 100K R 10M 1% 5% 5% 1% 5% 100K R 10M 200 ppm/C -55C to 155C -55C to 155C 150V 200V -55C to 155C 50V -55C to 125C 150V 200V -55C to 155C 50V 100K R 27M 100K R 10M 4.7M R 16M 1 R 100K 1 R 100K 1 R 100K 1 R 100K 1 R 10M -55C to 125C 1DB to 20D B 5% 10% 20% +0/-10% +0/-20% +0/-30% 0.3dB 0.5dB 1.0dB 2.0dB 100K R 27M 200 ppm/C 4.7M R 16M 200 ppm/C 1 R 100K 200 ppm/C 1 R 10 200 ppm/C 1M< R 10M 10< R 1M 100 ppm/C --- Note: " ! " is the symbol for new product 9 Resistor Chip General Information Ordering Information - Global part number Global part number - Single resistor (3) RC 0 6 03 J R 07 10R (L) Series name (code 1-2) RC = General purpose thick film RT = High precision - High stability thick film RJ = General purpose thin film RL = Low ohmic PR / PF / PT = Current sensor - low TCR TR = Trimmable SR = Surge AR = NiAu termination RV = High voltage AT = RF attenuator thick film Optional code (1/2) (code 17) Size code (code 3-6) (inch / metric) 0100 = 0.4 x 0.2 0201 = 0.6 x 0.3 0402 = 1.0 x 0.5 0603 = 1.6 x 0.8 0805 = 2.0 x 1.25 1206 = 3.2 x 1.6 1210 = 3.2 x 2.6 1218 = 3.2 x 4.5 2010 = 5.0 x 2.5 2512 = 6.35 x 3.2 Taping reel (code 10-11) 07 = 7 inch Dia. reel 10 = 10 inch Dia. reel 13 = 13 inch Dia. reel Tolerance (code 7) W = 0.05% B = 0.1% C = 0.25% D = 0.5% F = 1% G = 2% J = 5% (for Jumper ordering) K = 10% (for TR = 0/-10%) M = 20% (for TR = 0/-20%) N = 30% (for TR = 0/-30%) Resistance (code 12-16) 0R = Jumper 0R1 = 0.1 1R = 1 10R = 10 100R = 100 1K = 1 000 1M = 1 000 000 100M = 1 000 000 000 T. C. R. (code 9) B = 10 ppm/C (on request) C = 15 ppm/C (on request) D = 25 ppm/C E = 50 ppm/C M = 75 ppm/C F = 100 ppm/C L = 150 ppm/C G = 200 ppm/C "" = Based on spec. ( for thick film only) Packing style (code 8 ) R = Paper tape reel K = Embossed plastic tape reel C = Bulk cassette Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process" 2. On customized label. "LFP" or specific symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request) 3. Global Part Number is the preferred clear text code for ordering Yageo and Phycomp branded products. 10 Resistor Chip General Information Ordering Information - Global part number Global part number - Power enhancement RL 0805 J R 7 W 0R015 (L) Series name (code 1-2) RC = General purpose thick film RL = Low ohmic PR / PF / PT = Current sensor - low TCR Optional code (code 17) Resistance (code 12-16) 0R01 = 0.01 0R1 = 0.1 1R = 1 10R = 10 100R = 100 1K = 1 000 1M = 1 000 000 Size code (code 3-6) (inch / metric) 0805 = 2.0 x 1.25 1206 = 3.2 x 1.6 2010 = 5.0 x 2.5 2512 = 6.35 x 3.2 Power rating (code 11) W = 2 x standard power Tolerance (code 7) F = 1% G = 2% J = 5% Taping reel (code 10) 7 = 7 inch Dia. reel Packing style (code 8 ) R = Paper tape reel K = Embossed plastic tape reel T. C. R. (code 9) M = 75 ppm/C F = 100 ppm/C G = 200 ppm/C "" = Based on spec. ( for thick film only) Global part number - Arrays & Networks YC 16 4 J R Series name (code 1-2) YC = Aarray & Network (convex) thick film TC = Array (concave) thick film TA = Array (convex) thin film TD = Multi value array (convex) thin film Size code (inch) (code 3-4) 10 = 0201 x 2 (0202) 12 = 0402 x 2 (0404) 0402 x 4 (0408) 15 = 10Pin/8R (0612) 16 = 0603 x 2 (0606) 0603 x 4 (0612) 24 = 0602 x 8 (0616) 32 = 1206 x 4 (1224) 35 = 10Pin/8R (1225) Number of resistors (code 5) 2 = 2 resistors 4 = 4 resistors 8 = 8 resistors Schematic (code 6) L = L-type (for YC358) T = T-type (for YC158/358) "" = Based on spec. 07 10R (L) Optional code (code 17) Resistance (code 12-16) 0R = Jumper 0R1 = 0.1 1R = 1 10R = 10 100R = 100 1K = 1 000 1M = 1 000 000 Taping reel (code 10-11) 07 = 7 inch Dia. reel 10 = 10 inch Dia. reel 13 = 13 inch Dia. reel T.C.R. (code 9) D = 25 ppm/C E = 50 ppm/C "" = Based on spec. Packing style (code 8 ) R = Paper tape reel K = Embossed plastic tape reel Tolerance (code 7) B = 0.1% D = 0.5% F = 1% J = 5% (for Jumper ordering) 11 Resistor Chip General Information Ordering information for North America Phycomp CTC ordering code - Noth America Ordering example: 9C06031A10R0FKHFT = R-chip 0603, 10R0, 1%, 5K reel 1-2 XX 3-6 7-8 9-12 XXXX XX XXXX 13 14 15-16 X X XX X 17 Series name (code 1-2) 9C = Phycomp Thick film chip resistors 9T = Phycomp Thin film chip resistors Packing style (code 17 ) T = 5K paper 3 = 10K paper 4 = 20K paper 5 = 4K blister 6 = 5K blister 7 = 50K paper P = 25K bulk case Size code (standard resistors, code 3-6) 0201 0201 (0603) 0402 0402 (1005) 0603 0603 (1608) 0805 0805 (2012) 1206 1206 (3216) 1210 1210 (3225) 1218 1218 (3248) 2010 2010 (5025) 2512 2512 (6432) AC34 0603 (1608) 4R concave array AV34 0603 (1608) 4R convex array AV22 0402 (1005) 2R convex array AV24 0402 (1005) 4R convex array AV28 0402 (1005) 8R convex array RN31 10P8R in 1206 convex network FR01 1206 (3216) Fusible FR21 0603 (1608) Fusible SR01 1206 (3216) Surge VR01 1206 (3216) High voltage 5% VR02 1206 (3216) High voltage 1% VR11 0805 (2012) High voltage 5% VR12 0805 (2012) High voltage 1% VR21 2512 (6432) High voltage 5% MR22 2512 (6432) Current sensor - low TCR MF22 2512 (6432) Current sensor - low TCR V321 0404 (1010) RF attenuator Power rating (code 7-8) 1A 1/16W 0.063W 1A 1/10W 0.10W 2A 1/8W 0.125W 3A 1/4W 0.25W 5A 1/2W 0.5W 7A 1/20W 0.05W 8A 1/32W 0.03125W 12 3/4W 0.75W 1W 1W 1W 2W 2W 2W Resistance valre (code 9-12) 0R00 = Jumper R0XX < 0.1 RXXX = 0.1 - 0.976 XRXX = 1 - 9.76 XXRX = 10 - 97.6 XXX0 = 100 - 976 XXX1 = 1K - 9.76K XXX2 = 10K - 97.6K XXX3 = 100K - 9.78K XXX4 = 1M - 9.76M XXX5 = 10M - 97.6M XXX6 = 100M+ XXDB = 1 - 20DB 12 90402 (0603 (0805) (1206) (1210) (0201) (RN31) (2010) (1218/2512) Special coding (code 15-16) HF = SnPb PF = Lead free AF = NiAu T.C.R. (code 14) C = 10 ppm/C D = 15 ppm/C A = 25 ppm/C B = 50 ppm/C K = 100 ppm/C L = 200 ppm/C E = 250 ppm/C M = 300 ppm/C G = 500 ppm/C F = 0/+500 ppm/C R = 600 ppm/C Q = -100/+600 ppm/C P = 750 ppm/C H = 1000 ppm/C I = 1500 ppm/C J = 2000 ppm/C N = 3000 ppm/C dB values apply to Attenuators Right values apply to trimmable resistors Tolerance (code 13) E = 0.01% A = 0.05% B = 0.1%; 0.2dB C = 0.25%; 0.3dB D = 0.5%; 0.5dB F = 1%; 1dB G = 2%; 2dB J = 5% N = 0/-20% R = 0/-30% Resistor Chip General Information IEC publication 63, SPQ, last digit of 12NC Standard of values in a decade according to "IEC publication 63" E6 series 10 15 22 33 47 E12 series 10 12 15 18 22 E24 series 10 11 12 13 15 33 36 39 43 47 E96 series 100 102 105 107 110 133 137 140 143 147 178 182 187 191 196 237 243 249 255 261 316 324 332 340 348 422 432 442 453 464 562 576 590 604 619 750 768 787 806 825 68 27 16 51 113 150 200 267 357 475 634 845 33 18 56 115 154 205 274 365 487 649 866 39 20 62 118 158 210 280 374 499 665 887 47 22 68 121 162 215 287 383 511 681 909 56 24 75 124 165 221 294 392 523 698 931 68 27 82 127 169 226 301 402 536 715 953 82 30 91 130 174 232 309 412 549 732 976 Packing quantities Size code Tape width 0100 0201 0402 0603 0805 1206 1210 1218 2010 2512 YC102 YC122 TC122 ATV321 YC124 TC124 YC162 YC164 TC164 YC158 YC248 YC324 YC358 8mm 8mm 8mm 8mm 8mm 8mm 8mm 12mm 12mm 12mm 8mm 8mm 8mm 8mm 8mm 8mm 8mm 8mm 8mm 8mm 12mm 12mm 12mm 178mm / O7" reel Paper Embossed 10 000 --10 000 --10 000 --5 000 --5 000 --5 000 --5 000 ----4 000 --4 000 --4 000 10 000 --10 000 --10 000 --10 000 -10 000 --10 000 --5 000 --5 000 --5 000 --5 000 --5 000 4 000 --4 000 --4 000 254mm / O10" reel Paper --20 000 20 000 10 000 10 000 10 000 10 000 --------------20 000 20 000 -10 000 10 000 --------- 330mm / O13" reel Paper Embossed ----50 000 --50 000 --20 000 --20 000 --20 000 --20 000 --------16 000 --------50 000 --50 000 ------40 000 --40 000 ------20 000 --20 000 --20 000 --------------- Mass per 100 units Mass (g) 0.007 0.016 0.058 0.192 0.450 0.862 1.471 2.703 2.273 3.704 0.052 0.100 0.112 0.100 0.281 0.311 0.376 0.833 1.030 0.855 0.885 2.703 3.333 Volume mm3 0.0104 0.041 0.175 0.576 1.250 2.728 4.030 7.590 6.875 10.827 --------------------------- 12NC Ordering information The first 8 or 9 digits of the 12 digit catalogue number are given under section "Phycomp world wide - Traditional type" on following pages. The remaining 4 or 3 digits represent the resistance value with the last digit indicating the multiplier as shown in right table. Example: 0.001 = 0010 or 010 0.02 = 0200 or 200 0.3 = 3007 or 307 1 = 1008 or 108 33 k = 3303 or 333 10 M = 1006 or 106 Last digit of 12NC Resistance Last digit 0.001 to 0.0976 0 0.1 to 0.976 7 1 to 9.76 8 10 to 97.6 9 100 to 976 1 1 to 9.76 k 2 10 to 97.6 k 3 100 to 976 k 4 1 to 9.76 M 5 10 to 97.6 M 6 13 Resistor Chip Selection Charts Introduction to thick film genaral purpose and double power resistors Features * Extremely thin and light * Hightly reliable multilayer electrode construction * Compatible with all soldering process * Highly stable in auto-placement surface mounting applications * Barrier layer end termination * Zero ohm jumper is available * Available in 8mm tape & reel per EIA RS481 Derating curve Construction Maximum dissipation (P) in percentage of rated power as a function of the operating ambient temperature (Tamb). Overcoat (Epoxy) Primary glass layer 70 100 Rated Power (%) Resistor (RuO2) (Jumper chip is a conductor) 80 60 RC0402RC2512 40 RC0100RC0201 20 155 125 -55 -40 -20 0 20 40 60 80 100 120 External electrode (matte Tin) Alumina Substrate 140 160 Internal Electrode (Ag-Pd) Secondary Electrode (Nickel plated) Ambient Temperature (C) Dimensions I1 I1 H I2 I2 L 14 W unit: mm Type RC0100 RC0201 RC0402 RC0603 RC0805 RC1206 RC1210 RC1218 RC2010 RC2512 L 0.40 0.03 0.60 0.03 1.00 0.05 1.60 0.10 2.00 0.10 3.10 0.10 3.10 0.10 3.10 0.10 5.00 0.10 6.35 0.10 W 0.20 0.03 0.30 0.03 0.50 0.05 0.80 0.10 1.25 0.10 1.60 0.10 2.60 0.15 4.60 0.10 2.50 0.15 3.10 0.15 H 0.13 0.03 0.23 0.03 0.32 0.05 0.45 0.10 0.50 0.10 0.55 0.10 0.50 0.10 0.55 0.10 0.55 0.10 0.55 0.10 I1 0.10 0.03 0.10 0.05 0.20 0.10 0.25 0.15 0.35 0.20 0.45 0.20 0.45 0.15 0.45 0.20 0.55 0.15 0.60 0.20 I2 0.10 0.03 0.15 0.05 0.25 0.10 0.25 0.15 0.35 0.20 0.40 0.20 0.50 0.20 0.40 0.20 0.50 0.20 0.50 0.20 Resistor Chip Selection Charts Introduction to thick film genaral purpose and double power resistors Electrical characteristics Type Power Operating Temp. MWV RCOV DWV P70 range RC0100 1/32W -55C to +125C 15V 30V 30V E24 5% 10 - 1M Zero ohm jumper < 0.05 E24 5% E24/E96 1% E24/E96 0.5% Zero ohm jumper RC0201 1/20W -55C to +125C 25V 50V 50V RC0402 1/16W -55C to +155C 50V 100V 100V RC0603 1/10W -55C to +155C 50V 100V 100V RC0805 1/8W -55C to +155C 150V 300V 300V RC1206 1/4W -55C to +155C 200V 400V 500V RC1210 1/2W -55C to +155C 200V 500V 500V RC1218 -55C to +155C 200V 500V 500V RC2010 3/4W -55C to +155C 200V 500V 500V RC2512 -55C to +155C 200V 500V 500V Double power 1/4W -55C to +155C 150V RC0805 300V 300V Double power 1/2W -55C to +155C 200V RC1206 400V 500V Double power RC2512 400V 500V 1W 1W 2W -55C to +155C 200V T. C. R. ( ppm/C) Resistance range & tolerance 1 - 10M 1 - 1M 10 - 1M < 0.05 10 R 1M 250 Jumper criteria (unit: A) Rated current 0.5 Max. current 1.0 10 < R 10M 200 Rated current 0.5 1 R 10 -100/+350 Max. current 1.0 Rated current 1.0 Max. current 2.0 E24 5% E24/E96 1% E24/E96 0.5% Zero ohm jumper Rated current 1.0 Max. current 2.0 1 - 22M 1 - 10M 10 - 1M < 0.05 Rated current 2.0 Max. current 5.0 Rated current 2.0 Max. current 10.0 10 < R 10M 100 1 R 10 200 10M < R 22M E24 5% E24/E96 1% E24/E96 0.5% Zero ohm jumper 1 - 1M 1 - 1M 10 - 1M < 0.02 E24 5% E24/E96 1% E24/E96 0.5% Zero ohm jumper 1 - 22M 1 - 10M 10 - 1M < 0.05 Rated current 2.0 Max. current 10.0 Rated current 6.0 Max. current 10.0 Rated current 2.0 Max. current 10.0 Rated current 2.0 Max. current 10.0 Rated current 2.0 Max. current 5.0 E24 5% 1 - 100 E24/E96 1% 1 - 100 Zero ohm jumper < 0.05 1 R 100 200 E24 5% 1 - 150 E24/E96 1% 1 - 150 Zero ohm jumper < 0.05 1 R 150 200 Rated current 3.0 Max. current 7.5 Rated current 6.0 Max. current 15.0 Environmental characteristics Performance test Test method Procedure Requirements Life MIL-STD-202Gmethod 108A 1 000 hours at 70 5C applied RCWV 1.5 hours on, 0.5 hours off, still air required (3%+ 0.05) for 01005 (2%+ 0.05) for others < 100m for jumper High temperature exposure MIL-STD-202Gmethod 108A 1 000 hours at maximum operating temperature depending on specification, unpowered (1%+ 0.05) < 50m for jumper Moisture resistance MIL-STD-202Gmethod 106F Each temperature / humidity cycle is defined at 8 hours (method 106F), 3 cycles / 24 hours for 10d with 25C / 65C 95% R.H (3%+ 0.05) for 01005 (2%+ 0.05) for others < 100m for jumper Thermal shock MIL-STD-202Gmethod 107G LCT / UCT, number of cycles required is 300 Maximum transfer time is 20 seconds (0.5%+ 0.05) for 10K to 10M (1%+ 0.05) for others Wetting IPC/JEDECJSTD-002B testB Electrical test not required. Magnification 50X Leadfree solder bath at 245 3C Dipping time: 3 0.5 seconds Well tinned (95% covered) Resistance to soldering heat MIL-STD-202Gmethod 210F Leadfree solder, 270C, 10 seconds immersion time (1%+ 0.05) < 50m for jumper MIL-R-55342Dpara 4.7.5 2.5 times RCWV or maximum overload voltage whichever is less for 5 seconds at room temperature (2%+ 0.05) < 50m for jumper Solderability Short time overload 15 Resistor Chip Selection Charts 01005 to 0805 General Purpose thick film / RC series Size: inch (mm) 0201 (0603) 0402 (1005) 0603 (1608) 0805 (2012) 1/20W 1/16W 1/10W 1/8W Power P70 Tolerance 5% 1% 5% 1% 5% 1% 5% 1% Resistance Range E24 E24/E96 E24 E24/E96 E24 E24/E96 E24 E24/E96 Jumper 1 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 1 k 1.5 k 2.2 k 3.3 k 4.7 k 6.8 k 10 k 15 k 22 k 33 k 47 k 68 k 100 k 150 k 220 k 330 k 470 k 680 k 1 M 1.5 M 2.2 M 3.3 M 4.7 M 6.8 M 10 M 15 M 22 M Remark Note: Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor element and glass is exempted by RoHS. 16 Resistor Chip Selection Charts 01005 to 0805 Global part number - Preferred type for ordering Yageo / Phycomp branded products Ordering example: RC0603JR-07100K(L) RC 060 3 J R 07 100K (L) Optional code(1/2) (code 17) Series name (code 1-2) RC = General purpose thick film Resistance (code 12-16) 0R = Jumper 10R = 10 100R = 100 100K = 100K Size code (code 3-6) (inch / metric) 0100 = 0.4 x 0.2 0201 = 0.6 x 0.3 0402 = 1.0 x 0.5 0603 = 1.6 x 0.8 0805 = 2.0 x 1.25 1206 = 3.2 x 1.6 1210 = 3.2 x 2.6 1218 = 3.2 x 4.5 2010 = 5.0 x 2.5 2512 = 6.35 x 3.2 Taping reel (code 10-11) 07 = 7 inch Dia. reel 10 = 10 inch Dia. reel 13 = 13 inch Dia. reel T. C. R. (code 9) "" = Based on spec. ( for thick film only) Tolerance (code 7) D = 0.5% F = 1% J = 5% (for Jumper ordering) Packing style (code 8 ) R = Paper tape reel K = Embossed plastic tape reel C = Bulk cassette Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process" 2. On customized label. "LFP" or specific symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request) Phycomp world wide - Traditional type Size: inch (mm) Power Tolerance Resistance Packing Quantity 5 000 10 000 20 000 50 000 Jumper 5 000 10 000 20 000 50 000 0201 (0603) 1/20 W +5% +1% E24 E24 / E96 paper tape --- --- General purpose thick film / RC series 0402 (1005) 0603 (1608) 1/16 W 1/10 W +5% +1% +5% +1% E24 E24 / E96 E24 E24 / E96 paper tape paper tape --- 2322 803 70...L 2322 806 7....L 2322 705 70...L 2322 806 80...L 2322 806 8....L --- 2322 803 60...L 2322 806 6....L 2322 705 87...L 0805 (2012) 1/8 W +5% +1% E24 E24 / E96 paper tape --- 2322 702 60...L 2322 704 6....L 2322 730 61...L 2322 734 6....L 2322 706 7....L 2322 702 70...L 2322 704 7....L 2322 730 71...L 2322 734 7....L --- 2322 702 81...L 2322 704 8....L 2322 730 81...L 2322 734 8....L 2322 706 8....L --- --- --- --- --- --- --- --- 2322 702 96001L --- 2322 730 91002L --- 2322 803 91001L --- 2322 705 91001L --- 2322 702 97001L --- 2322 730 91003L --- --- --- --- --- 2322 702 92002L --- 2322 730 92002L --- --- --- 2322 705 91007L --- --- --- --- --- For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number. Phycomp CTC ordering code - Traditional type - North America Regional code for ordering Phycomp branded products. Please see page 12 for details. 17 Resistor Chip Selection Charts 1206 to 2512 General Purpose thick film / RC series Size: inch (mm) 1206 (3216) 1210 (3225) 1218 (3248) 2010 (5025) 2512 (6432) 1/4W 1/2W 1W 3/4W 1W Power P70 Tolerance 5% 1% 5% 1% 5% 1% 5% 1% 5% 1% Resistance Range E24 E24/E96 E24 E24/E96 E24 E24/E96 E24 E24/E96 E24 E24/E96 Jumper 1 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 1 k 1.5 k 2.2 k 3.3 k 4.7 k 6.8 k 10 k 15 k 22 k 33 k 47 k 68 k 100 k 150 k 220 k 330 k 470 k 680 k 1 M 1.5 M 2.2 M 3.3 M 4.7 M 6.8 M 10 M 15 M 22 M Remark Note: Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor element and glass is exempted by RoHS. 18 Resistor Chip Selection Charts 1206 to 2512 Global part number - Preferred type for ordering Yageo / Phycomp branded products Ordering example: RC1206JR-07100K(L) RC 1206 J R 07 100K (L) Optional code(1/2) (code 17) Series name (code 1-2) RC = General purpose thick film Resistance (code 12-16) 0R = Jumper 10R = 10 100R = 100 100K = 100K Size code (code 3-6) (inch / metric) 0100 = 0.4 x 0.2 0201 = 0.6 x 0.3 0402 = 1.0 x 0.5 0603 = 1.6 x 0.8 0805 = 2.0 x 1.25 1206 = 3.2 x 1.6 1210 = 3.2 x 2.6 1218 = 3.2 x 4.5 2010 = 5.0 x 2.5 2512 = 6.35 x 3.2 Taping reel (code 10-11) 07 = 7 inch Dia. reel 10 = 10 inch Dia. reel 13 = 13 inch Dia. reel T. C. R. (code 9) "" = Based on spec. ( for thick film only) Tolerance (code 7) D = 0.5% F = 1% J = 5% (for Jumper ordering) Packing style (code 8 ) R = Paper tape reel K = Embossed plastic tape reel C = Bulk cassette Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process" 2. On customized label. "LFP" or specific symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request) Phycomp world wide - Traditional type Size: inch (mm) Power Tolerance Resistance Packing Quantity 4 000 5 000 10 000 20 000 Jumper 4 000 5 000 10 000 20 000 1206 (3216) 1/4 W +5% +1% E24 E24 / E96 paper tape --- --- General purpose thick film / RC series 1210 (3225) 1218 (3248) 1/2 W 1W +5% +1% +5% +1% E24 E24 / E96 E24 E24 / E96 paper tape blister tape --- 2322 711 61...L 2322 724 6....L 2390 735 70...L 2322 711 51...L 2322 724 7....L --- 2322 711 81...L 2322 724 8....L 2390 735 71...L 2010 (5025) 3/4 W +5% +1% E24 E24 / E96 blister tape 2512 (6432) 1W +5% +1% E24 E24 / E96 blister tape --- 2322 735 64...L 2322 735 7....L 2322 760 60...L 2322 761 6....L 2322 762 60...L 2322 763 6....L 2390 735 3....L --- --- --- --- --- --- --- --- --- --- --- --- --- 2390 735 5....L --- --- --- --- --- --- --- --- --- --- 2322 735 90007L --- 2322 760 90003L --- 2322 762 90000L --- 2322 711 91032L --- 2390 735 90001L --- --- --- --- --- --- --- 2322 711 91005L --- --- --- --- --- --- --- --- --- 2322 711 92004L --- --- --- --- --- --- --- --- --- For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number. Phycomp CTC ordering code - Traditional type - North America Regional code for ordering Phycomp branded products. Please see page 12 for details. 19 Resistor Chip Selection Charts Introduction to thin film chip resistors Features RT series * High precision - high stability * Low TCR / low noise * High accuracy (0.05%, 0.1%, 0.25%, 0.5%, 1%) RJ series * General purpose * TCR: 50 ppm/C * Tolerance: 1% Derating curve Construction Maximum dissipation (P) in percentage of rated power as a function of the operating ambient temperature (Tamb). Overcoat 70 100 Rated Power (%) Resistor (NiCr) 80 60 40 External Electrode Alumina Substrate 20 125 -55 -40 -20 0 20 40 60 80 100 120 140 160 Internal Electrode (Ag-Pd) Secondary Electrode (Nickel Plated) Ambient Temperature (C) Dimensions I1 I1 H I2 I2 L 20 W unit: mm Type L W H I1 I2 RT / RJ0402 1.00 0.10 0.50 0.05 0.30 0.05 0.20 0.10 0.25 0.10 RT / RJ0603 1.60 0.10 0.80 0.10 0.45 0.10 0.25 0.15 0.25 0.15 RT / RJ 0805 2.00 0.10 1.25 0.10 0.50 0.10 0.35 0.20 0.35 0.20 RT / RJ1206 3.10 0.10 1.60 0.10 0.55 0.10 0.45 0.20 0.40 0.20 RT / RJ1210 3.10 0.10 2.60 0.15 0.50 0.10 0.50 0.20 0.50 0.20 RT / RJ2010 5.00 0.10 2.50 0.15 0.55 0.10 0.55 0.15 0.50 0.20 RT / RJ2512 6.35 0.10 3.20 0.15 0.55 0.10 0.60 0.20 0.50 0.20 Resistor Chip Selection Charts Introduction to thin film chip resistors Electrical characteristics Type Power P70 RT0402 RT0603 Operating Temp. range RCOV 1/16W 50V 100V 75V 1/10W 75V 150V 100V 10 R 681K RT0805 1/8W 150V 300V 200V RT1206 1/8W 200V 400V 300V RT1210 1/4W 200V 400V 400V E24/E96 0.05%, 0.1%, 10 R 1.5M 0.25%, 0.5%, 1% 10 R 1M RT2010 1/2W 200V 400V 400V RT2512 3/4W 200V 400V 400V RJ0402 1/16W 25V 100V 100V 10 R 121K RJ0603 1/16W 50V 100V 100V 5.1 R 681K RJ0805 1/10W 100V 200V 250V RJ1206 1/8W 150V 250V 250V RJ1210 1/4W 150V 250V 250V RJ2010 1/2W 150V 300V 400V RJ2512 3/4W 150V 300V 400V -55C to +125C DWV T. C. R. ( ppm/C) MWV Resistance range & tolerance 10 R 121K 50 25 15 10 10 R 1M E24/E96 1% 5.1 R 1.5M 50 10 R 1M Environmental characteristics Performance test Test method Procedure Life MIL-STD-202Gmethod 108A 1 000 hours at 70 5C applied RCWV 1.5 hours on, 0.5 hours off, still air required High temperature exposure MIL-STD-202Gmethod 108A 1 000 hours at maximum operating temperature depending on specification, unpowered Moisture resistance MIL-STD-202Gmethod 106F Each temperature / humidity cycle is defined at 8 hours (method 106F), 3 cycles / 24 hours for 10d with 25C / 65C 95% R.H Thermal shock MIL-STD-202Gmethod 107G LCT / UCT, number of cycles required is 300 Maximum transfer time is 20 seconds Short time overload MIL-R-55342Dpara 4.7.5 2.5 times RCWV or maximum overload voltage whichever is less for 5 seconds at room temperature Resistance to soldering heat MIL-STD-202Gmethod 210F Leadfree solder, 270C, 10 seconds immersion time (0.25% +0.05) for RT (0.5% +0.05) for RJ Wetting IPC/JEDECJSTD-002B testB Electrical test not required. Magnification 50X Leadfree solder bath at 245 3C Dipping time: 3 0.5 seconds Well tinned (95% covered) Solderability Requirements (0.25% +0.05) for RT (0.5% +0.05) for RJ 21 Resistor Chip Selection Charts High precision - High stability, 0402 / 0603 High precision - High stability Size: inch (mm) 0402 (1005) 0603 (1608) 1/16W 1/10W Power P70 Temp. range (C) Tolerance Resistance range -55 to +125 -55 to +125 1% 0.5% 0.25% 0.1% 1% 0.5% 0.25% 0.1% E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 1 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 1 k 1.5 k 2.2 k 3.3 k 4.7 k 6.8 k 10 k 15 k 22 k 33 k 47 k 68 k 100 k 150 k 220 k 330 k 470 k 680 k Remark Note: 1. 2. 3. 4. 5. Resistance range is upper to 2 M (depends on size) on request Value in "Resistance" means the minimum one Resistance E192; special value on request Tolerance = 0.05%, T.C.R. = 10 ppm/C; 15 ppm/C on request Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor element and glass is exempted by RoHS. 6. For detail data please refer to right side "Thin film product range against tolerance / T.C.R." 22 Resistor Chip Selection Charts High precision - High stability, 0402 / 0603 Global part number - Preferred type for ordering Yageo / Phycomp branded products Ordering example: RT0603DRE07100K(L) RT 0603 D R E 07 100K (L) Optional code (1/2) (code 17) Series name (code 1-2) RT = High precision - High stability thin film Resistance (code 12-16) 10R = 10 100R = 100 10K = 10K 100K = 100K Size code (code 3-6) (inch / metric) 0402 = 1.0 x 0.5 0603 = 1.6 x 0.8 0805 = 2.0 x 1.25 1206 = 3.2 x 1.6 1210 = 3.2 x 2.6 2010 = 5.0 x 2.5 2512 = 6.35 x 3.2 Taping reel (code 10-11) 07 = 7 inch Dia. reel 10 = 10 inch Dia. reel 13 = 13 inch Dia. reel Tolerance (code 7) W = 0.05% B = 0.1% C = 0.25% D = 0.5% F = 1% T. C. R. (code 9) B = 10 ppm/C (on request) C = 15 ppm/C (on request) D = 25 ppm/C E = 50 ppm/C Packing style (code 8 ) R = Paper tape reel K = Embossed plastic tape reel Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process" 2. On customized label. "LFP" or specific symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request) Phycomp world wide - Traditional type High precision - High stability Size: inch (mm) 0402 (1005) 0603 (1608) Power 1/16 W 1/10 W Tolerance 1% 0.5% 0.25% 0.1% 1% 0.5% 0.25% 0.1% Resistance E24 / E96 E24 / E96 Packing paper tape paper tape Quantity TC25 5 000 --------2390 604 7....L 2390 604 6....L 2390 604 5....L 2390 604 4....L --------2390 404 7....L 2390 404 6....L 2390 404 5....L 2390 404 4....L TC50 5 000 --------TC25 10 000 2390 607 7....L 2390 607 6....L 2390 607 5....L 2390 607 4....L --------TC50 10 000 2390 407 7....L 2390 407 6....L 2390 407 5....L 2390 407 4....L For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number. Phycomp CTC ordering code - Traditional type - North America Regional code for ordering Phycomp branded products. Please see page 12 for details. Thin film product range against tolerance / T.C.R. (ordering code) Tolerance T.C.R. (ppm/C) RT0402 RT0603 RT0805 RT1206 RT1210 RT2010 RT2512 10 (B) 0.05% (W) 0.1% (B) 0.25% (C) 0.5% (D) 1% (F) 15 (C) 25 (D) 10 (B) 15 (C) 25 (D) 50 (E) 10 (B) 15 (C) 25 (D) 50 (E) 25 (D) 50 (E) 50 (E) -- -- -- 10R - 100K 10R - 100K 10R - 121K 10R - 121K 10R - 100K 10R - 100K 10R - 121K 10R - 121K 10R - 121K 10R - 121K 10R - 121K 1K - 47K 1K - 47K 1K - 47K 10R - 100K 10R - 100K 10R - 681K 10R - 681K 10R - 100K 10R - 100K 10R - 681K 5R1 - 681K 10R - 681K 5R1 - 681K 5R1 - 681K 100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1.5M 10R - 1.5M 10R - 100K 10R - 100K 10R - 1.5M 5R1 - 1.5M 10R - 1.5M 5R1 - 1.5M 5R1 - 1.5M 100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1.5M 10R - 1.5M 10R - 100K 10R - 100K 10R - 1.5M 5R1 - 1.5M 10R - 1.5M 5R1 - 1.5M 5R1 - 1.5M 100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 100K 10R - 100K 10R - 1M 5R1 - 1M 10R - 1M 5R1 - 1M 5R1 - 1M 100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 1M 10R - 1M 10R - 1M 100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 1M 10R - 1M 10R - 1M 23 Resistor Chip Selection Charts High precision - High stability, 0805 to 1210 High precision - High stability Size: inch (mm) Power P70 Temp. range (C) Tolerance 1206 (3216) 1210 (3225) 1/8W 1/8W 1/4W -55 to +125 1% Resistance range 0805 (2012) 0.5% 0.25% -55 to +125 0.1% 1% 0.5% 0.25% -55 to +125 0.1% 1% 0.5% 0.25% 0.1% E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 1 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 1 k 1.5 k 2.2 k 3.3 k 4.7 k 6.8 k 10 k 15 k 22 k 33 k 47 k 68 k 100 k 150 k 220 k 330 k 470 k 680 k 1 M 1.5 M Remark Note: 1. 2. 3. 4. 5. Value in "Resistance" means the minimum one Jumper; Resistance E192; special value on request T.C.R. = 10 ppm/C; 15 ppm/C on request Tolerance = 0.01%; 0.05% on Request Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor element and glass is exempted by RoHS. 6. For detail data please refer to right side "Thin film product range against tolerance / T.C.R." 24 Resistor Chip Selection Charts High precision - High stability, 0805 to 1210 Global part number - Preferred type for ordering Yageo / Phycomp branded products Ordering example: RT0805DRE07100K(L) RT 0805 D R E 07 100K (L) Optional code (1/2) (code 17) Series name (code 1-2) RT = High precision - High stability thin film Resistance (code 12-16) 10R = 10 100R = 100 10K = 10K 100K = 100K Size code (code 3-6) (inch / metric) 0402 = 1.0 x 0.5 0603 = 1.6 x 0.8 0805 = 2.0 x 1.25 1206 = 3.2 x 1.6 1210 = 3.2 x 2.6 2010 = 5.0 x 2.5 2512 = 6.35 x 3.2 Taping reel (code 10-11) 07 = 7 inch Dia. reel 10 = 10 inch Dia. reel 13 = 13 inch Dia. reel Tolerance (code 7) W = 0.05% B = 0.1% C = 0.25% D = 0.5% F = 1% T. C. R. (code 9) B = 10 ppm/C (on request) C = 15 ppm/C (on request) D = 25 ppm/C E = 50 ppm/C Packing style (code 8 ) R = Paper tape reel K = Embossed plastic tape reel Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process" 2. On customized label. "LFP" or specific symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request) Phycomp world wide - Traditional type Size: inch (mm) Power Tolerance Resistance Packing Quantity TC10 5 000 TC15 5 000 TC25 5 000 TC50 5 000 1% 0805 (2012) 1/8 W 0.5% 0.25% E24 / E96 paper tape High precision - High stability 1206 (3216) 1/4 W 0.1% 1% 0.5% 0.25% E24 / E96 paper tape 0.1% 1% 1210 (3225) 1/2 W 0.5% 0.25% E24 / E96 paper tape 0.1% 2390 801 7....L 2390 801 6....L 2390 801 5....L 2390 801 4....L 2390 811 7....L 2390 811 6....L 2390 811 5....L 2390 811 4....L 2390 812 7....L 2390 812 6....L 2390 812 5....L 2390 812 4....L 2390 701 7....L 2390 701 6....L 2390 701 5....L 2390 701 4....L 2390 711 7....L 2390 711 6....L 2390 711 5....L 2390 711 4....L 2390 712 7....L 2390 712 6....L 2390 712 5....L 2390 712 4....L 2390 601 7....L 2390 601 6....L 2390 601 5....L 2390 601 4....L 2390 611 7....L 2390 611 6....L 2390 611 5....L 2390 611 4....L 2390 612 7....L 2390 612 6....L 2390 612 5....L 2390 612 4....L 2390 401 7....L 2390 401 6....L 2390 401 5....L 2390 401 4....L 2390 411 7....L 2390 411 6....L 2390 411 5....L 2390 411 4....L 2390 412 7....L 2390 412 6....L 2390 412 5....L 2390 412 4....L For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number. Phycomp CTC ordering code - Traditional type - North America Regional code for ordering Phycomp branded products. Please see page 12 for details. Thin film product range against tolerance / T.C.R. (ordering code) Tolerance T.C.R. (ppm/C) RT0402 RT0603 RT0805 RT1206 RT1210 RT2010 RT2512 10 (B) 0.05% (W) 0.1% (B) 0.25% (C) 0.5% (D) 1% (F) 15 (C) 25 (D) 10 (B) 15 (C) 25 (D) 50 (E) 10 (B) 15 (C) 25 (D) 50 (E) 25 (D) 50 (E) 50 (E) -- -- -- 10R - 100K 10R - 100K 10R - 121K 10R - 121K 10R - 100K 10R - 100K 10R - 121K 10R - 121K 10R - 121K 10R - 121K 10R - 121K 1K - 47K 1K - 47K 1K - 47K 10R - 100K 10R - 100K 10R - 681K 10R - 681K 10R - 100K 10R - 100K 10R - 681K 5R1 - 681K 10R - 681K 5R1 - 681K 5R1 - 681K 100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1.5M 10R - 1.5M 10R - 100K 10R - 100K 10R - 1.5M 5R1 - 1.5M 10R - 1.5M 5R1 - 1.5M 5R1 - 1.5M 100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1.5M 10R - 1.5M 10R - 100K 10R - 100K 10R - 1.5M 5R1 - 1.5M 10R - 1.5M 5R1 - 1.5M 5R1 - 1.5M 100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 100K 10R - 100K 10R - 1M 5R1 - 1M 10R - 1M 5R1 - 1M 5R1 - 1M 100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 1M 10R - 1M 10R - 1M 100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 1M 10R - 1M 10R - 1M 25 Resistor Chip Selection Charts High precision - High stability, 2010 / 2512 High precision - high stability Size: inch (mm) 2010 (5025) 2512 (6432) 1/2W 3/4W Power P70 Temp. range (C) Tolerance Resistance range -55 to +125 -55 to +125 1% 0.5% 0.25% 0.1% 1% 0.5% 0.25% 0.1% E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 10 15 22 33 47 68 100 150 220 330 470 680 1 k 1.5 k 2.2 k 3.3 k 4.7 k 6.8 k 10 k 15 k 22 k 33 k 47 k 68 k 100 k 150 k 220 k 330 k 470 k 680 k 1 M Remark Note: 1. 2. 3. 4. 5. Jumper; Resistance E192; special value on request Value in "Resistance" means the minimum one. T.C.R. = 10 ppm/C; 15 ppm/C on request Tolerance = 0.01%; 0.05% on request Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor element and glass is exempted by RoHS. 6. For detail data please refer to right side "Thin film product range against tolerance / T.C.R." 26 Resistor Chip Selection Charts High precision - High stability, 2010 / 2512 Global part number - Preferred type for ordering Yageo / Phycomp branded products Ordering example: RT2010DRE07100K(L) RT 2010 D R E 07 100K (L) Optional code (1/2) (code 17) Series name (code 1-2) RT = High precision - High stability thin film Resistance (code 12-16) 10R = 10 100R = 100 10K = 10K 100K = 100K Size code (code 3-6) (inch / metric) 0402 = 1.0 x 0.5 0603 = 1.6 x 0.8 0805 = 2.0 x 1.25 1206 = 3.2 x 1.6 1210 = 3.2 x 2.6 2010 = 5.0 x 2.5 2512 = 6.35 x 3.2 Taping reel (code 10-11) 07 = 7 inch Dia. reel 10 = 10 inch Dia. reel 13 = 13 inch Dia. reel Tolerance (code 7) W = 0.05% B = 0.1% C = 0.25% D = 0.5% F = 1% T. C. R. (code 9) B = 10 ppm/C (on request) C = 15 ppm/C (on request) D = 25 ppm/C E = 50 ppm/C Packing style (code 8 ) R = Paper tape reel K = Embossed plastic tape reel Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process" 2. On customized label. "LFP" or specific symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request) Phycomp world wide - Traditional type Size: inch (mm) Power Tolerance Resistance Packing Quantity TC10 4 000 TC15 4 000 TC25 4 000 TC50 4 000 High precision - High stability 2010 (5025) 1/2 W 0.5% 0.25% 0.1% 1% E24 / E96 blister tape 1% 2512 (6432) 3/4 W 0.5% 0.25% E24 / E96 blister tape 0.1% 2390 815 7....L 2390 815 6....L 2390 815 5....L 2390 815 4....L 2390 818 7....L 2390 818 6....L 2390 818 5....L 2390 818 4....L 2390 731 7....L 2390 731 6....L 2390 731 5....L 2390 731 4....L 2390 735 7....L 2390 735 6....L 2390 735 5....L 2390 735 4....L 2390 615 7....L 2390 615 6....L 2390 615 5....L 2390 615 4....L 2390 618 7....L 2390 618 6....L 2390 618 5....L 2390 618 4....L 2390 415 7....L 2390 415 6....L 2390 415 5....L 2390 415 4....L 2390 418 7....L 2390 418 6....L 2390 418 5....L 2390 418 4....L For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number. Phycomp CTC ordering code - Traditional type - North America Regional code for ordering Phycomp branded products. Please see page 12 for details. Thin film product range against tolerance / T.C.R. (ordering code) Tolerance T.C.R. (ppm/C) RT0402 RT0603 RT0805 RT1206 RT1210 RT2010 RT2512 10 (B) 0.05% (W) 0.1% (B) 0.25% (C) 0.5% (D) 1% (F) 15 (C) 25 (D) 10 (B) 15 (C) 25 (D) 50 (E) 10 (B) 15 (C) 25 (D) 50 (E) 25 (D) 50 (E) 50 (E) -- -- -- 10R - 100K 10R - 100K 10R - 121K 10R - 121K 10R - 100K 10R - 100K 10R - 121K 10R - 121K 10R - 121K 10R - 121K 10R - 121K 1K - 47K 1K - 47K 1K - 47K 10R - 100K 10R - 100K 10R - 681K 10R - 681K 10R - 100K 10R - 100K 10R - 681K 5R1 - 681K 10R - 681K 5R1 - 681K 5R1 - 681K 100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1.5M 10R - 1.5M 10R - 100K 10R - 100K 10R - 1.5M 5R1 - 1.5M 10R - 1.5M 5R1 - 1.5M 5R1 - 1.5M 100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1.5M 10R - 1.5M 10R - 100K 10R - 100K 10R - 1.5M 5R1 - 1.5M 10R - 1.5M 5R1 - 1.5M 5R1 - 1.5M 100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 100K 10R - 100K 10R - 1M 5R1 - 1M 10R - 1M 5R1 - 1M 5R1 - 1M 100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 1M 10R - 1M 10R - 1M 100R - 100K 100R - 100K 100R - 100K 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 100K 10R - 100K 10R - 1M 10R - 1M 10R - 1M 10R - 1M 10R - 1M 27 Resistor Chip Selection Charts General Purpose, 0402 to 2512 General purpose thin film / RJ Series Size: inch (mm) Power P70 Tolerance Temperature Coefficient of Resistance Resistance Range 0402 (1005) 0603 (1608) 0805 (2012) 1206 (3216) 1210 (3225) 2010 (5025) 2512 (6432) 1/16W 1/16W 1/10W 1/8W 1/4W 1/2W 3/4W 1% 1% 1% 1% 1% 1% 1% 50 ppm/C 50 ppm/C 50 ppm/C 50 ppm/C 50 ppm/C 50 ppm/C 50 ppm/C E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 E24/E96 1 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 1 k 1.5 k 2.2 k 3.3 k 4.7 k 6.8 k 10 k 15 k 22 k 33 k 47 k 68 k 100 k 150 k 220 k 330 k 470 k 680 k 1 M 1.5 M Remark Note: 1. Value in "Resistance" means the minimum one. 2. Resistance E192; special value on request 3. Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor element and glass is exempted by RoHS. 28 Resistor Chip Selection Charts General Purpose, 0402 to 2512 Global part number - Preferred type for ordering Yageo / Phycomp branded products Ordering example: RJ0603FRE07100K(L) RJ 0603 F R E 07 100K (L) Optional code (1/2) (code 17) Series name (code 1-2) RJ = General purpose thin film Resistance (code 12-16) 10R = 10 100R = 100 10K = 10K 100K = 100K Size code (code 3-6) (inch / metric) 0402 = 1.0 x 0.5 0603 = 1.6 x 0.8 0805 = 2.0 x 1.25 1206 = 3.2 x 1.6 1210 = 3.2 x 2.6 2010 = 5.0 x 2.5 2512 = 6.35 x 3.2 Taping reel (code 10-11) 07 = 7 inch Dia. reel 10 = 10 inch Dia. reel 13 = 13 inch Dia. reel Tolerance (code 7) F = 1% T. C. R. (code 9) E = 50 ppm/C Packing style (code 8 ) R = Paper tape reel K = Embossed plastic tape reel Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process" 2. On customized label. "LFP" or specific symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request) Phycomp world wide - Traditional type Size: inch (mm) Power Tolerance Resistance Packing Quantity 4 000 5 000 10 000 20 000 50 000 0402 (1005) 1/16 W +1% E24 / E96 paper tape 0603 (1608) 1/16 W +1% E24 / E96 paper tape General purpose thin film / RJ series 0805 (2012) 1206 (3216) 1/10 W 1/8 W +1% +1% E24 / E96 E24 / E96 paper tape paper tape 1210 (3225) 1/4 W +1% E24 / E96 paper tape 2010 (5025) 1/2 W +1% E24 / E96 blister tape 2512 (6432) 3/4 W +1% E24 / E96 blister tape --- --- --- --- --- 2390 415 8....L 2390 418 8....L --- 2390 404 8....L 2390 401 8....L 2390 411 8....L 2390 412 0....L --- --- 2390 407 8....L 2391 424 8....L 2391 421 8....L 2391 431 8....L 2391 432 8....L --- --- 2390 427 8....L 2392 444 8....L 2392 441 8....L 2392 451 8....L 2392 412 8....L --- --- 2390 447 8....L --- --- --- --- --- --- For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number. Phycomp CTC ordering code - Traditional type - North America Regional code for ordering Phycomp branded products. Please see page 12 for details. Thin film product range against tolerance / T.C.R. (ordering code) Tolerance T.C.R. (ppm/C) RJ0402 RJ0603 RJ0805 RJ1206 RJ1210 RJ2010 RJ2512 1% (F) 50 (E) 10R - 121K 5R1 - 681K 5R1 - 1.5M 5R1 - 1.5M 10R - 1M 10R - 1M 10R - 1M 29 Resistor Chip Selection Charts Introduction to thick film array / network resistors Features TC arrays * Integrated discrete chip resistors from 2 to 8 pcs * More efficient in pick & place application * Low assembly costs * Reduced size of final equipment YC networks * Higher component and equipment reliability YC arrays Schematics YC102/122/162 4 YC124/164/324 3 5 6 7 YC248 8 16 15 14 13 12 YC358 (L-Type) 11 10 9 10 9 R8 R1 R2 R1 R2 R3 R4 R1 R2 R3 R4 R5 R6 R7 R7 1 2 2 R1 = R2 TC122 4 3 4 1 R1 = R2 = R3 = R4 2 3 4 5 6 7 R2 R1 R2 10 9 R3 2 1 2 R1 = R2 3 8 R7 R6 6 R5 1 8 R2 2 R3 3 R4 4 5 R1 = R2 = R3 = R4 = R5 = R6 = R7 = R8 YC358 (T-Type) 7 R6 6 10 R5 9 R8 8 R7 7 R6 6 R5 R4 R1 1 7 YC158 8 R8 R1 6 R1 = R2 = R3 = R4 = R5 = R6 = R7 = R8 TC124/164 3 5 7 R8 R1 1 8 1 4 R1 = R2 = R3 = R4 R2 R3 2 3 R4 4 R1 5 1 R1 = R2 = R3 = R4 = R5 = R6 = R7 = R8 R2 2 R3 3 R4 4 5 R1 = R2 = R3 = R4 = R5 = R6 = R7 = R8 Dimensions T W1 W2 Side view for all types Type H / H2 YC102 H: 0.35 0.10 B P L T W1 W2 0.20 0.10 0.50 0.05 0.80 0.10 0.35 0.10 0.15 0.10 0.60 0.10 YC122 H: 0.21 +0.10/-0.05 0.20 0.10 0.67 0.05 1.00 0.10 0.35 0.10 0.25 0.10 1.00 0.10 YC 102/122/162 YC 124/164/324 158/358/248 H H P a YC162 H: 0.30 0.10 0.30 0.10 0.80 0.05 1.60 0.10 0.40 0.10 0.30 0.10 1.60 0.10 YC124 H: 0.45 0.05 0.20 0.15 0.50 0.05 2.00 0.10 0.45 0.10 0.30 0.15 1.00 0.10 YC164 H: 0.65 0.05 0.30 0.15 0.80 0.05 3.20 0.15 0.60 0.10 0.30 0.15 1.60 0.15 YC324 H: 1.10 0.15 H2: 0.90 0.15 0.50 0.20 1.27 0.05 5.08 0.20 0.60 0.10 0.50 0.15 3.20 0.20 YC248 H: 0.45 0.05 H2: 0.30 0.05 0.30 0.15 0.50 0.05 4.00 0.20 0.45 0.10 0.40 0.15 1.60 0.15 TC122 H: 0.30 0.05 0.25 0.15 0.50 0.05 1.00 0.10 0.30 0.10 0.25 0.15 1.00 0.10 TC124 H: 0.30 0.10 H2: 0.25 0.10 0.20 0.10 0.50 0.05 2.00 0.10 0.40 0.10 0.25 0.10 1.00 0.10 TC164 H: --H2: 0.60 0.15 0.30 0.15 0.80 0.05 3.20 0.15 0.60 0.10 0.30 0.15 1.60 0.15 YC158 H: 0.45 0.05 0.30 0.15 0.64 0.05 3.20 0.20 0.60 0.10 0.35 0.15 1.60 0.15 YC358 H: 1.10 0.15 H2: 0.90 0.15 0.50 0.15 1.27 0.05 6.40 0.20 0.60 0.10 0.50 0.15 3.20 0.20 B B P a H2 L L TC 122 TC 124/164 H H P a B B P L Note: "H2" is valued on button view 30 a H2 L unit: mm Resistor Chip Selection Charts Introduction to thick film array / network resistors Electrical characteristics Type Power P70 Operating Temp. range MWV RCOV DWV YC102 1/32W -55C to +125C 15V 30V 30V E24 5% 10 R 1M E24/E96 1% 10 R 1M Zero ohm jumper < 0.05 Rated current 0.5 Max. current 1.0 YC122 1/16W -55C to +125C 50V 100V 100V E24 5% 1 R 1M E24/E96 1% 10 R 1M Zero ohm jumper < 0.05 Rated current 1.0 Max. current 2.0 YC162 1/16W -55C to +125C 50V 100V 100V E24 5% 10 R 1M Zero ohm jumper < 0.05 Rated current 1.0 Max. current 2.0 YC124 1/16W -55C to +155C 25V 50V 100V E24 5% 10 R 1M E24/E96 1% 10 R 1M Zero ohm jumper < 0.05 Rated current 1.0 Max. current 2.0 YC164 1/16W -55C to +155C 50V 100V 100V E24 5% 1 R 1M E24/E96 1% 1 R 1M Zero ohm jumper < 0.05 Rated current 1.0 Max. current 2.0 YC324 1/8W -55C to +155C 200V 500V 500V E24 5% 10 R 1M E24/E96 1% 10 R 1M YC248 1/16W -55C to +155C 50V 100V 100V E24 5% 10 R 1M E24/E96 1% 10 R 1M Zero ohm jumper < 0.05 Rated current 2.0 Max. current 10.0 TC122 1/16W -55C to +125C 50V 100V 100V E24 5% 10 R 1M E24/E96 1% 10 R 1M Zero ohm jumper < 0.05 Rated current 1.0 Max. current 1.5 TC124 1/16W -55C to +125C 50V 100V 100V E24 5% 10 R 1M E24/E96 1% 10 R 1M Zero ohm jumper < 0.05 Rated current 1.0 Max. current 1.5 TC164 1/16W -55C to +155C 50V 100V 100V E24 5% 10 R 1M E24/E96 1% 10 R 1M Zero ohm jumper < 0.05 Rated current 1.0 Max. current 2.0 YC158 YC358 1/16W 1/16W -55C to +155C -55C to +155C 25V 50V 50V 100V 50V 100V Resistance range & tolerance T. C. R. ( ppm/C) Jumper criteria (unit: A) 200 -- -- E24 5% 10 R 100K E24 5% 10 R 330K -- --- -- Environmental characteristics Performance test Test method Procedure Requirements Life MIL-STD-202Gmethod 108A 1 000 hours at 70 5C applied RCWV 1.5 hours on, 0.5 hours off, still air required (2% +0.05) < 100m for jumper High temperature exposure MIL-STD-202Gmethod 108A 1 000 hours at maximum operating temperature depending on specification, unpowered (1% +0.05) < 50m for jumper Moisture resistance MIL-STD-202Gmethod 106F Each temperature / humidity cycle is defined at 8 hours (method 106F), 3 cycles / 24 hours for 10d with 25C / 65C 95% R.H (2% +0.05) < 100m for jumper Thermal shock MIL-STD-202Gmethod 107G LCT / UCT, number of cycles required is 300 Maximum transfer time is 20 seconds (0.5% +0.05) for 10K to 10M (1% +0.05) for others Wetting IPC/JEDECJSTD-002B testB Electrical test not required. Magnification 50X Leadfree solder bath at 245 3C Dipping time: 3 0.5 seconds Well tinned (95% covered) Resistance to soldering heat MIL-STD-202Gmethod 210F Leadfree solder, 270C, 10 seconds immersion time (1% +0.05) < 50m for jumper MIL-R-55342Dpara 4.7.5 2.5 times RCWV or maximum overload voltage whichever is less for 5 seconds at room temperature (2% +0.05) < 50m for jumper Solderability Short time overload 31 Resistor Chip Selection Charts Arrays, convex and concave Arrays Series Size: inch (mm) Power P70 Tolerance YC / TC 122 series YC / TC 124 series YC248 series YC / TC 164 series YC324 series 2 x 0402 (1 x 1) 4 x 0402 (2 x 1) 8 x 0602 (4.0 x 1.6) 4 x 0603 (3.2 x 1.6) 4 x 1206 (5.2 x 3.1) 1/16W 1/16W 1/16W 1/16W 1/8W 5% R-Array/R Type -Network (convex) Resistance Range E24 1% 5% 1% 5% 1% 5% 1% 5% 1% 5% R-Array/R R-Array/R R-Array/R R-Array/R R-Array/R R-Array/R R-Array/R R-Array/R R-Array/R R-Array/R -Network -Network -Network -Network -Network -Network -Network -Network -Network -Network (convex) (convex) (convex) (convex) (convex) (convex) (convex) (concave) (convex) (convex) E24/E96 E24 E24/E96 E24 E24/E96 E24 E24/E96 E24 E24/E96 E24 Jumper 10 15 22 33 47 68 100 150 220 330 470 680 1 k 1.5 k 2.2 k 3.3 k 4.7 k 6.8 k 10 k 15 k 22 k 33 k 47 k 68 k 100 k 150 k 220 k 330 k 470 k 680 k 1 M Remark Note: 1. 2. 3. 4. 32 Zero ohm Jumper <0.05 Value in "Resistance" means the minimum one 4 x 0603 (Concave) 1% on request Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor element and glass is exempted by RoHS. Resistor Chip Selection Charts Arrays, convex and concave Global part number - Arrays & Networks Ordering example: YC122-JR-07100K(L) YC 12 2 J R 07 100K (L) Series name (code 1-2) YC = Aarray & Network (convex) thick film TC = Array (concave) thick film TA = Array (convex) thin film TD = Multi value array (convex) thin film Optional code (code 17) Resistance (code 12-16) 0R = Jumper 10R = 10 100R = 100 100K = 100K Size code (inch) (code 3-4) 10 = 0201 x 2 (0202) 12 = 0402 x 2 (0404) 0402 x 4 (0408) 15 = 10Pin/8R (0612) 16 = 0603 x 2 (0606) 0603 x 4 (0612) 24 = 0602 x 8 (0616) 32 = 1206 x 4 (1224) 35 = 10Pin/8R (1225) Taping reel (code 10-11) 07 = 7 inch Dia. reel 10 = 10 inch Dia. reel 13 = 13 inch Dia. reel T.C.R. (code 9) "" = Based on spec. Packing style (code 8 ) R = Paper tape reel K = Embossed plastic tape reel Number of resistors (code 5) 2 = 2 resistors 4 = 4 resistors 8 = 8 resistors Tolerance (code 7) F = 1% J = 5% (for Jumper ordering) Schematic (code 6) L = L-type (for YC358) T = T-type (for YC158/358) "" = Based on spec. Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process" 2. On customized label. "LFP" or specific symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request) Phycomp world wide - Traditional type Array thick film chip resistors Size: inch / mm Power Tolerance Type 2 X 0402 / 1X1 4 X 0402 / 2X1 1/16 W +5% 8 X 0402 / 4.0 X 1.6 1/16 W +1% +5% 4 X 0603 / 3.2 X 1.3 1/16 W +1% +5% +1% +5% 1/16 W +1% 4 X1206 / 5.2 X 3.1 +5% 1/8 W +5% R-array / R-array / R-array / R-array / R-array / R-array / R-array / R-array / R-array / R-array / R-network R-network R-network R-network R-network R-network R-network R-network R-network R-network (convex) (convex) (convex) (convex) (convex) (convex) (convex) (convex) (convex) (convex) Resistance E24 E24 / E96 E24 E24 / E96 E24 E24 / E96 E24 E24 / E96 E24 E24 Packing paper tape paper tape paper tape paper tape blister tape ------------------2350 039 10...L Quantity 4 000 --------2350 053 10...L 2350 043 1....L 2350 035 10...L 2350 025 1....L 2350 034 10...L --5 000 ------------10 000 2350 013 11...L 2350 013 2....L 2350 033 11...L 2350 023 2....L --------2350 053 91001L --2350 035 91001L --2350 034 91001L --Jumper 5 000 --2350 033 91001L --------------10 000 2350 013 91001L For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number. Phycomp CTC ordering code - Traditional type - North America Regional code for ordering Phycomp branded products. Please see page 12 for details. 33 Resistor Chip Selection Charts Networks, T-type and L-type Network series YC158 series YC358 series 0612 (1632) 1225 (3264) Power P70 1/16W 1/16W Tolerance 5% T-Type 10 Pin, PIN 5 and PIN 10 no resistance E24 Size: inch (mm) Type Resistance Range 5% T-Type 10 Pin, PIN 5 and PIN 10 no resistance E24 L-Type 10 Pin, PIN 1 and PIN 6 no resistance E24 10 15 22 33 47 68 100 150 220 330 470 680 1 k 1.5 k 2.2 k 3.3 k 4.7 k 6.8 k 10 k 15 k 22 k 33 k 47 k 68 k 100 k 150 k 220 k 330 k Remark Note: 1. 2. 3. 4. 34 8R-Network, convex termintions Zero ohm Jumper <0.05 Value in "Resistance" means the minimum one. Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor element and glass is exempted by RoHS. Resistor Chip Selection Charts Networks, T-type and L-type Global part number - Arrays & Networks Ordering example: YC158TJR-07100K(L) YC 15 8 T J R 07 100K (L) Series name (code 1-2) YC = Aarray & Network (convex) thick film TC = Array (concave) thick film Optional code (code 17) Resistance (code 12-16) 0R = Jumper 10R = 10 100R = 100 100K = 100K Size code (inch) (code 3-4) 10 = 0201 x 2 (0202) 12 = 0402 x 2 (0404) 0402 x 4 (0408) 15 = 10Pin/8R (0612) 16 = 0603 x 2 (0606) 0603 x 4 (0612) 24 = 0602 x 8 (0616) 32 = 1206 x 4 (1224) 35 = 10Pin/8R (1225) Taping reel (code 10-11) 07 = 7 inch Dia. reel 13 = 13 inch Dia. reel T.C.R. (code 9) "" = Based on spec. Number of resistors (code 5) 2 = 2 resistors 4 = 4 resistors 8 = 8 resistors Packing style (code 8 ) R = Paper tape reel K = Embossed plastic tape reel Tolerance (code 7) F = 1% J = 5% (for Jumper ordering) Schematic (code 6) L = L-type (for YC358) T = T-type (for YC158/358) "" = Based on spec. Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process" 2. On customized label. "LFP" or specific symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request) Phycomp world wide - Traditional type Network thick film chip resistors Size: inch (mm) Power Tolerance 0612 (1632) 1/32 W +5% 1225 (3264) 1/16 W +5% Type T-type 10 Pin / 8R PIN 5 and PIN 10 no resistance T-type 10 Pin / 8R PIN 5 and PIN 10 no resistance L-type 10 Pin / 8R PIN 1 and PIN 6 no resistance Resistance Packing Quantity 4 000 5 000 E24 paper tape --2350 230 10...L E24 E24 blister tape 2350 201 10...L --- 2350 200 10...L --- For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number. Phycomp CTC ordering code - Traditional type - North America Regional code for ordering Phycomp branded products. Please see page 12 for details. 35 Resistor Chip Selection Charts Introduction to thin film array chip resistors Features * Precision * Low TCR * Reduced size of final equipment * Lower assembly costs * Higher component and equipment reliability Derating curve Schematics Maximum dissipation (P) in percentage of rated power as a function of the operating ambient temperature (Tamb). TA164 8 TD164 6 5 8 7 6 5 70 100 Rated Power (%) 7 R1 80 R2 R3 R4 R1 R2 R3 R4 60 1 40 2 3 4 1 2 R1 = R2 = R3 = R4 20 R1 3 R2 R3 4 R4 125 -55 -40 -20 0 20 40 60 80 100 120 140 160 Ambient Temperature (C) Dimensions TA/TD 164 H H3 P H4 H2 T B W1 W2 top view button view side view unit: mm L Type 36 H H3 B P L H2 H4 T W1 W2 TA164 0.65 0.05 0.50 0.15 0.30 0.15 0.80 0.05 3.20 0.15 0.50 0.15 0.65 0.05 0.50 0.10 0.30 0.15 1.60 0.15 TD164 0.65 0.10 0.50 0.10 0.30 0.15 0.80 0.15 3.20 0.20 0.40 0.10 0.50 0.10 0.50 0.10 0.30 0.15 1.60 0.10 Resistor Chip Selection Charts Introduction to thin film array chip resistors Electrical characteristics Type Power P70 Operating Temp. range MWV RCOV DWV TA164 1/16W -55C to +125C 75V 150V 150V E24/E96 0.1%, 0.5%, 1% 10 R 330K TD164 1/16W -55C to +125C 75V 150V 150V E24/E96 0.1%, 0.5%, 1% 10 R 330K Resistance range & tolerance T. C. R. ( ppm/C) 25 50 Note: See page 11 for ordering code. For more detailed, please contact with sales offices, distributors and representatives in your region. Environmental characteristics Performance test Test method Procedure Requirements Life MIL-STD-202Gmethod 108A 1 000 hours at 70 5C applied RCWV 1.5 hours on, 0.5 hours off, still air required (0.25% +0.05) for TD164 (0.5% +0.05) for TA164 High temperature exposure MIL-STD-202Gmethod 108A 1 000 hours at maximum operating temperature depending on specification, unpowered Satisfy electrical and physical characteristic Moisture resistance MIL-STD-202Gmethod 106F Each temperature / humidity cycle is defined at 8 hours (method 106F), 3 cycles / 24 hours for 10d with 25C / 65C 95% R.H Thermal shock MIL-STD-202Gmethod 107G LCT / UCT, number of cycles required is 300 Maximum transfer time is 20 seconds Wetting IPC/JEDECJSTD-002B testB Electrical test not required. Magnification 50X Leadfree solder bath at 245 3C Dipping time: 3 0.5 seconds Well tinned (95% covered) Resistance to soldering heat MIL-STD-202Gmethod 210F Leadfree solder, 270C, 10 seconds immersion time Satisfy electrical and physical characteristic MIL-R-55342Dpara 4.7.5 2.5 times RCWV or maximum overload voltage whichever is less for 5 seconds at room temperature (0.25% +0.05) for TD164 (0.5% +0.05) for TA164 Solderability Short time overload (0.25% +0.05) for TD164 (0.5% +0.05) for TA164 37 Resistor Chip Selection Charts Introduction to low ohmic / low ohmic high power chip resistors Features * Current sensing of desktop & notebook PC * Resistance values down to 0.010 * Highly reliable multilayer electrode construction * Low inductance * High speed logic circuits Derating curve Construction Maximum dissipation (P) in percentage of rated power as a function of the operating ambient temperature (Tamb). Overcoat (Epoxy) Primary glass layer 70 100 Rated Power (%) Resistor (Ag) 80 60 40 External electrode (matte Tin) Alumina Substrate 20 125 -55 -40 -20 0 20 40 60 80 100 120 140 160 Internal Electrode (Ag-Pd) Secondary Electrode (Nickel plated) Ambient Temperature (C) Dimensions I1 I1 H I2 I2 L 38 W unit: mm Type L W H I1 I2 RL0402 1.00 0.10 0.50 0.05 0.35 0.05 0.20 0.10 0.25 0.10 RL0603 1.60 0.10 0.80 0.10 0.45 0.10 0.25 0.15 0.25 0.15 RL0805 2.00 0.10 1.25 0.10 0.50 0.10 0.35 0.20 0.35 0.20 RL1206 3.10 0.10 1.60 0.10 0.55 0.10 0.45 0.20 0.450.20 RL1210 3.10 0.10 2.60 0.15 0.50 0.10 0.50 0.20 0.50 0.20 RL1218 3.05 0.15 4.60 0.10 0.55 0.10 0.45 0.25 0.50 0.25 RL2010 5.00 0.10 2.50 0.15 0.55 0.10 0.60 0.20 0.50 0.20 RL2512 6.35 0.10 3.20 0.15 0.55 0.10 0.60 0.20 0.50 0.20 Resistor Chip Selection Charts Introduction to low ohmic / low ohmic high power chip resistors Electrical characteristics Type Power P70 Operating Temp. range RL0402 1/16W -55C to +125C RL0603 1/10W -55C to +125C RL0805 1/8W -55C to +125C RL1206 1/4W -55C to +125C RL1210 1/2W -55C to +125C RL1218 1W -55C to +125C RL2010 3/4W -55C to +125C RL2512 1W -55C to +125C High power RL0805 1/4W -55C to +125C High power RL1206 1/2W -55C to +125C T. C. R. ( ppm/C) Resistance range & tolerance 0.05 R < 1 E24 1%, 2%, 5% 0.01 R < 1 See following table "T.C.R.- RL series" 0.015 R < 1 T. C. R. - RL series Type Operating Temp. range Resistance range RL0402 -55C to +125C 50mR<1 T. C. R. 50m - 1 800 ppm/C 10m - 36m 36m - 91m 91m - 500m 500m - 1 1 200 ppm/C 800 ppm/C 300 ppm/C RL0603 -55C to +125C 10mR<1 1 500 ppm/C 10m - 18m 20m - 47m 51m - 91m 100m - 360m 390m - 500m 510m - 1 RL0805 -55C to +125C 10mR<1 1 500 ppm/C 1 200 ppm/C 1 000 ppm/C 600 ppm/C 300 ppm/C 200 ppm/C RL1206 -55C to +125C 10mR<1 1 500 ppm/C 1 200 ppm/C 1 000 ppm/C 600 ppm/C 300 ppm/C 200 ppm/C RL1210 -55C to +125C 10mR<1 1 500 ppm/C 1 000 ppm/C 800 ppm/C 600 ppm/C 300 ppm/C 200 ppm/C 10m - 30m 33m - 56m 60m - 180m 200m - 1 2 000 ppm/C 1 000 ppm/C 250 ppm/C 10m - 18m 20m - 47m 51m - 91m 100m - 360m 390m - 500m 510m - 1 RL1218 -55C to +125C 10mR<1 700 ppm/C RL2010 -55C to +125C 10mR<1 1 500 ppm/C 1 200 ppm/C 1 000 ppm/C 600 ppm/C 300 ppm/C 200 ppm/C RL2512 -55C to +125C 10m R<1 1 500 ppm/C 1 200 ppm/C 800 ppm/C 600 ppm/C 300 ppm/C 200 ppm/C Environmental characteristics Performance test Test method Procedure Requirements Life MIL-STD-202Gmethod 108A 1 000 hours at 70C 5C applied RCWV 1.5 hours on, 0.5 hours off, still air required 2% High temperature exposure MIL-STD-202Gmethod 108A 1 000 hours at maximum operating temperature depending on specification, unpowered 1% Moisture resistance MIL-STD-202Gmethod 106F Each tempperature / humidity cycle is defined at 8 hours (method 106F), 3 cycles / 24 hours for 10d with 25C / 65C 95% R.H 2% Thermal shock MIL-STD-202Gmethod 107G LCT / UCT, number of cycles required is 300 Maximum transfer time is 20 seconds 1% Wetting IPC/JEDECJSTD-002B testB Electrical test not required. Magnification 50X Leadfree solder bath at 245 3C Dipping time: 3 0.5 seconds Well tinned (95% covered) Resistance to soldering heat MIL-STD-202Gmethod 210F Leadfree solder, 270C, 10 seconds immersion time 1% MIL-R-55342Dpara 4.7.5 2.5 times RCWV or maximum overload voltage whichever is less for 5 seconds at room temperature 2% Solderability Short time overload 39 Resistor Chip Selection Charts Low ohmic, 0201 to 1206 Low ohmic / RL series Size: inch (mm) 0402 (1005) 0603 (1608) 0805 (2012) 1206 (3216) 1/16W 1/10W 1/8W 1/4W Power P70 Tolerance 5% 1% 5% 1% 5% 1% 5% 1% Resistance Range E24 E24 E24 E24 E24 E24 E24 E24 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 Remark Note: 1. 2. 3. 4. 40 Value in "Resistance" means the minimum one E48/E96 on request The partial values of 25 / 40 / 50 / 60 / 250 / 400 / 500 m are also available Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor element and glass is exempted by RoHS. Resistor Chip Selection Charts Low ohmic, 0201 to 1206 Global part number - Preferred type Ordering example: RL0603JR-070R01(L) RL 0603 J R 07 0R01 Series name (code 1-2) RL = Low ohmic Size code (code 3-6) (inch / metric) 0402 = 1.0 x 0.5 0603 = 1.6 x 0.8 0805 = 2.0 x 1.25 1206 = 3.2 x 1.6 1210 = 3.2 x 2.6 1218 = 3.2 x 4.5 2010 = 5.0 x 2.5 2512 = 6.35 x 3.2 Tolerance (code 7) F = 1% G = 2% J = 5% (for Jumper ordering) (L) Optional code(1/2) (code 17) Resistance (code 12-16) 0R01 = 0.01 0R1 = 0.1 0R2 = 0.2 Taping reel (code 10-11) 07 = 7 inch Dia. reel 10 = 10 inch Dia. reel 13 = 13 inch Dia. reel T. C. R. (code 9) "" = Based on spec. ( for thick film only) Packing style (code 8 ) R = Paper tape reel K = Embossed plastic tape reel Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process" 2. On customized label. "LFP" or specific symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request) Phycomp world wide - Traditional type Low ohmic chip resistors Size: inch (mm) 0402 (1005) 0603 (1608) 0805 (2012) 1206 (3216) Power 1/16 W 1/10 W 1/8 W 1/4 W Tolerance +5% +1% +5% +1% +5% +1% +5% +1% Resistance E24 E24 E24 E24 E24 E24 E24 E24 Packing paper tape paper tape paper tape paper tape ----2350 512 10...L 2350 512 12...L 2350 511 10...L 2350 511 12...L 2350 510 10...L 2350 510 12...L Quantity 5 000 ------------10 000 2350 513 20...L 2350 513 22...L For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number. Phycomp CTC ordering code - Traditional type - North America Regional code for ordering Phycomp branded products. Please see page 12 for details. 41 Resistor Chip Selection Charts Low ohmic, 1210 to 2512 Low ohmic / RL series Size: inch (mm) 1210 (3225) 1218 (3248) 2010 (5025) 2512 (6432) 1/2W 1W 3/4W 1W Power P70 Tolerance 5% 1% 5% 1% 5% 1% 5% 1% Reisitance Range E24 E24 E24 E24 E24 E24 E24 E24 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 Remark Note: 1. 2. 3. 4. 42 Value in "Resistance" means the minimum one E48/E96 on request The partial values of 25 / 40 / 50 / 60 / 250 / 400 / 500 m are also available Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor element and glass is exempted by RoHS. Resistor Chip Selection Charts Low ohmic, 1210 to 2512 Global part number - Preferred type Ordering example: RL1210JR-070R01(L) RL 1210 J R 07 0R01 (L) Optional code(1/2) (code 17) Series name (code 1-2) RL = Low ohmic Resistance (code 12-16) 0R01 = 0.01 0R1 = 0.1 0R2 = 0.2 Size code (code 3-6) (inch / metric) 0402 = 1.0 x 0.5 0603 = 1.6 x 0.8 0805 = 2.0 x 1.25 1206 = 3.2 x 1.6 1210 = 3.2 x 2.6 1218 = 3.2 x 4.5 2010 = 5.0 x 2.5 2512 = 6.35 x 3.2 Taping reel (code 10-11) 07 = 7 inch Dia. reel T. C. R. (code 9) "" = Based on spec. ( for thick film only) Tolerance (code 7) F = 1% G = 2% J = 5% (for Jumper ordering) Packing style (code 8 ) R = Paper tape reel K = Embossed plastic tape reel Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process" 2. On customized label. "LFP" or specific symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request) Phycomp world wide - Traditional type Size: inch (mm) 1210 (3225) Power 1/2 W Tolerance +5% +1% Resistance E24 E24 Packing paper tape ----Quantity 4 000 2390 735 3....L 5 000 2390 735 90..0L/60..7L Low ohmic chip resistors 1218 (3248) 1W +5% +1% E24 E24 blister tape 2322 735 64...L 2322 735 7....L --- --- 2010 (5025) 3/4 W +5% +1% E24 E24 blister tape 2512 (6432) 1W +5% +1% E24 E24 blister tape 2322 760 90..0L/60..7L 2322 761 90..0L/6...7L 2322 762 90..0L/60..7L 2322 763 90..0L/6...7L --- --- --- --- For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number. Phycomp CTC ordering code - Traditional type - North America Regional code for ordering Phycomp branded products. Please see page 12 for details. 43 Resistor Chip Selection Charts Low ohmic, high power, 0805 / 1206 Low ohmic high power / RL-High power series Size: inch (mm) Power P70 0805 (2012) 1206 (3216) 1/4W 1/2W Tolerance 5% 1% 5% 1% Resistance Range E24 E24 E24 E24 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 Remark Note: 1. E48/E96 on request 2. The partial values of 25 / 40 / 50 / 60 / 250 / 400 / 500 m are also available 3. Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor element and glass is exempted by RoHS. 44 Resistor Chip Selection Charts Low ohmic, high power, 0805 / 1206 Global part number - Preferred type Ordering example: RL0805JR-7W0R01(L) RL 0805 J R 7W 0R01 (L) Series name (code 1-2) RL = Low ohmic Optional code (code 17) Resistance (code 12-16) 0R01 = 0.01 0R1 = 0.1 0R2 =0.2 Size code (code 3-6) (inch / metric) 0805 = 2.0 x 1.25 1206 = 3.2 x 1.6 Taping reel (code 10-11) Tolerance (code 7) F = 1% G = 2% J = 5% 7W = 7 inch Dia. reel and 2 x standard power type T. C. R. (code 9) "" = Based on spec. ( for thick film only) Packing style (code 8 ) R = Paper tape reel Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process" 2. On customized label. "LFP" or specific symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request) Phycomp world wide - Traditional type Size: inch (mm) Power Tolerance Resistance Packing Quantity 5 000 +5% E24 2350 511 15...L Low ohmic high power chip resistors 0805 (2012) 1/4 W +1% E24 / E96 paper tape 2350 511 17...L 1206 (3216) 1/2 W +5% E24 +1% E24 / E96 paper tape 2350 519 01...L 2350 519 1....L For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number. Phycomp CTC ordering code - Traditional type - North America Regional code for ordering Phycomp branded products. Please see page 12 for details. 45 Resistor Chip Selection Charts Introduction to high ohmic chip resistors Features * Reduced size of final equipment * Low assembly costs * Higher component and equipment reliability * High ohmic values up to 100MW * Suitable for power supplies in small equipments Derating curve Construction Maximum dissipation (P) in percentage of rated power as a function of the operating ambient temperature (Tamb). Overcoat (Epoxy) Primary glass layer 70 100 Rated Power (%) Resistor (RuO2) 80 60 40 External electrode (matte Tin) Alumina Substrate 20 155 -55 -40 -20 0 20 40 60 80 100 120 140 160 Internal Electrode (Ag-Pd) Secondary Electrode (Nickel plated) Ambient Temperature (C) Dimensions I1 I1 H I2 I2 L 46 W unit: mm Type L W H I1 I2 RC0805 2.00 0.10 1.25 0.10 0.50 0.10 0.35 0.20 0.35 0.20 RC1206 3.10 0.10 1.60 0.10 0.55 0.10 0.45 0.20 0.40 0.20 Resistor Chip Selection Charts Introduction to high ohmic chip resistors Electrical characteristics Type Power P70 Operating Temp. range MWV RCOV DWV RC0805 1/8W -55C to +155C 150V 300V 300V RC1206 1/4W -55C to +155C 200V 400V 500V Resistance range & tolerance T. C. R. ( ppm/C) E24 5%, 10%, 20% 24M R 100M 300 Note: See page 10 for ordering code. For more detailed, please contact with sales offices, distributors and representatives in your region. Environmental characteristics Performance test Test method Procedure Requirements Life MIL-STD-202Gmethod 108A 1 000 hours at 70 5C applied RCWV 1.5 hours on, 0.5 hours off, still air required (2% +0.05) High temperature exposure MIL-STD-202Gmethod 108A 1 000 hours at maximum operating temperature depending on specification, unpowered (1% +0.05) Moisture resistance MIL-STD-202Gmethod 106F Each temperature / humidity cycle is defined at 8 hours (method 106F), 3 cycles / 24 hours for 10d with 25C / 65C 95% R.H (2% +0.05) Thermal shock MIL-STD-202Gmethod 107G LCT / UCT, number of cycles required is 300 Maximum transfer time is 20 seconds (0.5% +0.05) (1% +0.05) Wetting IPC/JEDECJSTD-002B testB Electrical test not required. Magnification 50X Leadfree solder bath at 245 3C Dipping time: 3 0.5 seconds Well tinned (95% covered) Resistance to soldering heat MIL-STD-202Gmethod 210F Leadfree solder, 270C, 10 seconds immersion time (1% +0.05) MIL-R-55342Dpara 4.7.5 2.5 times RCWV or maximum overload voltage whichever is less for 5 seconds at room temperature (2% +0.05) Solderability Short time overload 47 Resistor Chip Selection Charts Introduction to Ni/Au terminations chip resistors Features * New Ni/Au terminations provide special application for hybrid board gluing * Competitive with AgPd terminations * Special use in high temperature environment * Higher component and equipment reliability Derating curve Construction Maximum dissipation (P) in percentage of rated power as a function of the operating ambient temperature (Tamb). Overcoat (Epoxy) Primary glass layer 70 100 Rated Power (%) Resistor (RuO2) (Jumper chip is a conductor) 80 60 40 External electrode (matte Tin) Alumina Substrate 20 155 -55 -40 -20 0 20 40 60 80 100 120 140 160 Internal Electrode (Ag-Pd) Secondary Electrode (Nickel plated) Ambient Temperature (C) Dimensions I1 I1 H I2 I2 L 48 W unit: mm Type L W H I1 I2 AR0402 1.00 0.05 0.50 0.05 0.35 0.05 0.20 0.10 0.25 0.10 AR0603 1.60 0.10 0.80 0.10 0.45 0.10 0.25 0.15 0.25 0.15 AR0805 2.00 0.10 1.25 0.10 0.50 0.10 0.35 0.20 0.35 0.20 AR1206 3.10 0.10 1.60 0.10 0.55 0.10 0.45 0.20 0.40 0.20 Resistor Chip Selection Charts Introduction to Ni/Au terminations chip resistors Electrical characteristics Type Power Operating Temp. MWV RCOV DWV P70 range AR0402 1/16W -55C to +155C 50V 100V 100V AR0603 1/10W -55C to +155C 50V 100V 100V AR0805 1/8W -55C to +125C 150V 300V 300V AR1206 1/4W -55C to +125C 200V 500V 500V T. C. R. ( ppm/C) Resistance range & tolerance Jumper criteria (unit: A) Rated current 1.0 Max. current 2.0 E24 5% E24/E96 1% 1 R 10M Zero ohm jumper < 0.05 10 < R 10M 100 1 R 10 200 Rated current 1.0 Max. current 2.0 Rated current 2.0 Max. current 5.0 Rated current 2.0 Max. current 10.0 Environmental characteristics Performance test Test method Procedure Requirements Life MIL-STD-202Gmethod 108A 1 000 hours at 70 5C applied RCWV 1.5 hours on, 0.5 hours off, still air required (2% +0.05) <100m for jumper High temperature exposure MIL-STD-202Gmethod 108A 1 000 hours at maximum operating temperature depending on specification, unpowered (1% +0.05) <50m for jumper Moisture resistance MIL-STD-202Gmethod 106F Each temperature / humidity cycle is defined at 8 hours (method 106F), 3 cycles / 24 hours for 10d with 25C / 65C 95% R.H (2% +0.05) <100m for jumper Thermal shock MIL-STD-202Gmethod 107G LCT / UCT, number of cycles required is 300 Maximum transfer time is 20 seconds (0.5% +0.05) for 10K to 10M (1% +0.05) for others Wetting IPC/JEDECJSTD-002B testB Electrical test not required. Magnification 50X Leadfree solder bath at 245 3C Dipping time: 3 0.5 seconds Well tinned (95% covered) Resistance to soldering heat MIL-STD-202Gmethod 210F Leadfree solder, 270C, 10 seconds immersion time (1% +0.05) <50m for jumper MIL-R-55342Dpara 4.7.5 2.5 times RCWV or maximum overload voltage whichever is less for 5 seconds at room temperature (2% +0.05) <50m for jumper Solderability Short time overload 49 Resistor Chip Selection Charts 0402 to 1206 Chip resistors with NiAu terminations / AR series Size: inch (mm) 0402 (1005) 0603 (1608) 0805 (2012) 1206 (3216) 1/16W 1/10W 1/8W 1/4W Power P70 Tolerance 5% 1% 5% 1% 5% 1% 5% 1% Resistance Range E24 E24/E96 E24 E24/E96 E24 E24/E96 E24 E24/E96 Jumper 1 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 1 k 1.5 k 2.2 k 3.3 k 4.7 k 6.8 k 10 k 15 k 22 k 33 k 47 k 68 k 100 k 150 k 220 k 330 k 470 k 680 k 1 M 1.5 M 2.2 M 3.3 M 4.7 M 6.8 M 10 M Remark Note: 1. Zero ohm Jumper <0.05 2. Value in "Resistance" means the minimum one 3. Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor element and glass is exempted by RoHS. 50 Resistor Chip Selection Charts 0402 to 1206 Global part number - Preferred type for ordering Yageo / Phycomp branded products Ordering example: AR0603JR-07100K AR 0603 J R 07 100K (L) Series name (code 1-2) AR = NiAu termination Size code (code 3-6) (inch / metric) 0402 = 1.0 x 0.5 0603 = 1.6 x 0.8 0805 = 2.0 x 1.25 1206 = 3.2 x 1.6 Tolerance (code 7) F = 1% J = 5% (for Jumper ordering) Optional code(1/2) (code 17) Resistance (code 12-16) 0R = Jumper 10R = 10 100R = 100 100K = 100K Taping reel (code 10-11) 07 = 7 inch Dia. reel T. C. R. (code 9) "" = Based on spec. ( for thick film only) Packing style (code 8 ) R = Paper tape reel Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process" 2. On customized label. "LFP" or specific symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request) Phycomp world wide - Traditional type Chip resistors with Ni/Au terminations Size: inch (mm) 0402 (1005) 0603 (1608) 0805 (2012) Power 1/16 W 1/10 W 1/8 W Tolerance +5% +1% +5% +1% +5% +1% Resistance E24 E24 / E96 E24 E24 / E96 E24 E24 / E96 Packing paper tape paper tape paper tape ----2322 702 11... 2322 704 1.... 2322 730 11... 2322 734 1.... Quantity 5 000 --------10 000 2322 705 12... 2322 706 2.... ----2322 702 19001 --2322 730 19001 --Jumper 5 000 ----------10 000 2322 705 19001 1206 (3216) 1/4 W +5% +1% E24 E24 / E96 paper tape 2322 711 11... 2322 729 1.... --- --- 2322 711 19001 --- --- --- For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number. Phycomp CTC ordering code - Traditional type - North America Regional code for ordering Phycomp branded products. Please see page 12 for details. 51 Resistor Chip Selection Charts Introduction to Surge chip resistors Features * Reduced size of final equipment * Low assembly costs * Higher component and equipment reliability * Excellent performance at pulse loading Derating curve Construction Maximum dissipation (P) in percentage of rated power as a function of the operating ambient temperature (Tamb). Overcoat (Epoxy) (Jumper chip is a conductor) Primary glass layer 70 100 Rated Power (%) Resistor (RuO2) 80 60 40 External electrode (matte Tin) Alumina Substrate 20 155 -55 -40 -20 0 20 40 60 80 100 120 140 160 Internal Electrode (Ag-Pd) Secondary Electrode (Nickel plated) Ambient Temperature (C) Dimensions I1 I1 H I2 I2 L 52 W unit: mm Type L W H I1 I2 SR0805 2.00 0.10 1.25 0.10 0.50 0.10 0.35 0.20 0.35 0.20 SR1206 3.10 0.10 1.60 0.10 0.55 0.10 0.45 0.20 0.40 0.20 SR1218 3.10 0.10 4.60 0.10 0.55 0.10 0.45 0.20 0.40 0.20 SR2512 6.35 0.10 3.10 0.15 0.55 0.10 0.60 0.20 0.50 0.20 Resistor Chip Selection Charts Introduction to Surge chip resistors Electrical characteristics Type Power P70 Operating Temp. range MWV RCOV DWV SR0805 1/8W -55C to +155C 150V 300V 300V SR1206 1/4W -55C to +155C 150V 400V 500V SR1218 1W -55C to +155C 200V 400V 500V SR2512 1W -55C to +155C 200V 400V 500V Resistance range & tolerance T. C. R. ( ppm/C) E24 5%, 10%, 20% 1 R 100K 200 Environmental characteristics Performance test Test method Procedure Requirements Life MIL-STD-202Gmethod 108A 1 000 hours at 70 5C applied RCWV 1.5 hours on, 0.5 hours off, still air required (2% +0.05) High temperature exposure MIL-STD-202Gmethod 108A 1 000 hours at maximum operating temperature depending on specification, unpowered (1% +0.05) Moisture resistance MIL-STD-202Gmethod 106F Each temperature / humidity cycle is defined at 8 hours (method 106F), 3 cycles / 24 hours for 10d with 25C / 65C 95% R.H (2% +0.05) Thermal shock MIL-STD-202Gmethod 107G LCT / UCT, number of cycles required is 300 Maximum transfer time is 20 seconds (0.5% +0.05) for 10K to 10M (1% +0.05) for others Wetting IPC/JEDECJSTD-002B testB Electrical test not required. Magnification 50X Leadfree solder bath at 245 3C Dipping time: 3 0.5 seconds Well tinned (95% covered) Resistance to soldering heat MIL-STD-202Gmethod 210F Leadfree solder, 270C, 10 seconds immersion time (1% +0.05) MIL-R-55342Dpara 4.7.5 2.5 times RCWV or maximum overload voltage whichever is less for 5 seconds at room temperature (2% +0.05) Solderability Short time overload 53 Resistor Chip Selection Charts 0805 to 2512 Surge / SR series Size: inch (mm) 0805 (2012) 1206 (3216) 1218 (3248) 2512 (6432) Power P70 1/8W 1/4W 1W 1W Tolerance 5% 5% 5% 5% Resistance Range E24 E24 E24 E24 1 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 1 k 1.5 k 2.2 k 3.3 k 4.7 k 6.8 k 10 k 15 k 22 k 33 k 47 k 68 k 100 k Remark Note: 1. Value in "Resistance" means the minimum one 2. Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor element and glass is exempted by RoHS. 54 Resistor Chip Selection Charts 0805 to 2512 Global part number - Preferred type for ordering Yageo / Phycomp branded products Ordering example: SR0805MR-07100K(L) SR 0805 M R 07 100K (L) Optional code(1/2) (code 17) Series name (code 1-2) SR = Surge Resistance (code 12-16) 10R = 10 100K = 100K Size code (code 3-6) (inch / metric) 0805 = 2.0 x 1.25 1206 = 3.2 x 1.6 1218 = 3.2 x 4.5 2512 = 6.35 x 3.2 Taping reel (code 10-11) 07 = 7 inch Dia. reel T. C. R. (code 9) "" = Based on spec. ( for thick film only) Tolerance (code 7) J = 5% (for Jumper ordering) K = 10% M = 20% Packing style (code 8 ) R = Paper tape reel K = Embossed plastic tape reel Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process" 2. On customized label. "LFP" or specific symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request) Phycomp world wide - Traditional type Size: inch (mm) Power Tolerance Resistance Packing Quantity 4 000 5 000 1206 (3216) 1/4 W +5% E24 paper tape Surge chip resistors 1218 (3248) 1W +10% E24 paper tape --- --- 2350 554 12...L 2350 550 10...L 0805 (2012) 1/8 W +10% E24 paper tape +5% E24 paper tape 2512 (6432) 1W +10% E24 paper tape +20% E24 paper tape 2350 557 10...L 2350 556 11...L 2350 556 10...L 2350 556 13...L --- --- --- --- For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number. Phycomp CTC ordering code - Traditional type - North America Regional code for ordering Phycomp branded products. Please see page 12 for details. 55 Resistor Chip Selection Charts Introduction to high voltage chip resistors Features * Higher maximum working voltage to RC series * Extremely thin and light * Reliable electrode construction * Compatible with lead containing and lead free soldering processes * Highly stable in auto-placement surface mounting Derating curve Construction Maximum dissipation (P) in percentage of rated power as a function of the operating ambient temperature (Tamb). Overcoat (Epoxy) Primary glass layer 70 100 Rated Power (%) Resistor (RuO2) (Jumper chip is a conductor) 80 60 40 External electrode (matte Tin) Alumina Substrate 20 155 -55 -40 -20 0 20 40 60 80 100 120 140 160 Internal Electrode (Ag-Pd) Secondary Electrode (Nickel plated) Ambient Temperature (C) Dimensions I1 I1 H I2 I2 L 56 W unit: mm Type L W H I1 I2 RV0805 2.00 0.10 1.25 0.10 0.50 0.10 0.35 0.20 0.35 0.20 RV1206 3.10 0.10 1.60 0.10 0.55 0.10 0.40 0.20 0.40 0.20 RV2512 6.35 0.10 3.10 0.15 0.55 0.10 0.60 0.20 0.50 0.20 Resistor Chip Selection Charts Introduction to high voltage chip resistors Electrical characteristics Type Power P70 Operating Temp. range MWV RCOV DWV Resistance range & tolerance T. C. R. ( ppm/C) RV0805 1/8W -55C to +155C 400V 800V 800V E24 5% 100K R 10M E24/E96 1% 200 RV1206 1/4W -55C to +155C 500V 1000V 1000V E24 5% 100K R 27M E24/E96 1% 200 RV2512 1W -55C to +155C 500V 1000V 1000V E24 5% 4.7M R 16M 200 Environmental characteristics Performance test Test method Procedure Requirements Life MIL-STD-202Gmethod 108A 1 000 hours at 70 5C applied RCWV 1.5 hours on, 0.5 hours off, still air required (2% +0.05) High temperature exposure MIL-STD-202Gmethod 108A 1 000 hours at maximum operating temperature depending on specification, unpowered (1% +0.05) Moisture resistance MIL-STD-202Gmethod 106F Each temperature / humidity cycle is defined at 8 hours (method 106F), 3 cycles / 24 hours for 10d with 25C / 65C 95% R.H (2% +0.05) Thermal shock MIL-STD-202Gmethod 107G LCT / UCT, number of cycles required is 300 Maximum transfer time is 20 seconds (0.5% +0.05) for 10K to 10M (1% +0.05) for others Wetting IPC/JEDECJSTD-002B testB Electrical test not required. Magnification 50X Leadfree solder bath at 245 3C Dipping time: 3 0.5 seconds Well tinned (95% covered) Resistance to soldering heat MIL-STD-202Gmethod 210F Leadfree solder, 270C, 10 seconds immersion time (1% +0.05) MIL-R-55342Dpara 4.7.5 2.5 times RCWV or maximum overload voltage whichever is less for 5 seconds at room temperature (2% +0.05) Solderability Short time overload 57 Resistor Chip Selection Charts 0805 to 2512 High voltage / RV series Size: inch (mm) 0805 (2012) 1206 (3216) 2512 (6432) Working Voltage 400V 500V 500V Power P70 1/8W Tolerance Resistance Range 1/4W 1W 5% 1% 5% 1% 5% E24 E24/E96 E24 E24/E96 E24 100 k 150 k 220 k 330 k 470 k 680 k 1 M 1.5 M 2.2 M 3.3 M 4.7 M 6.8 M 10 M 15 M 22 M Remark Note: 1. Value in "Resistance" means the minimum one 2. Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor element and glass is exempted by RoHS. 58 Resistor Chip Selection Charts 0805 to 2512 Global part number - Preferred type for ordering Yageo / Phycomp branded products Ordering example: RV0805JR-07100K(L) RV 0805 J R 07 100K (L) Optional code(1/2) (code 17) Series name (code 1-2) RV = High voltage Resistance (code 12-16) 100K = 100K 1M = 1M Size code (code 3-6) (inch / metric) 0805 = 2.0 x 1.25 1206 = 3.2 x 1.6 2512 = 6.35 x 3.2 Taping reel (code 10-11) 07 = 7 inch Dia. reel Tolerance (code 7) F = 1% J = 5% (for Jumper ordering) T. C. R. (code 9) "" = Based on spec. ( for thick film only) Packing style (code 8 ) R = Paper tape reel K = Embossed plastic tape reel Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process" 2. On customized label. "LFP" or specific symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request) Phycomp world wide - Traditional type High voltage chip resistors Size: inch (mm) Power Tolerance Resistance Packing Quantity 4 000 5 000 0805 (2012) 1/8 W +5% E24 1206 (3216) 1/4 W +1% E24 / E96 +5% E24 --- --- --- --- 2322 762 98...L 2322 792 61...L 2322 793 6....L 2322 790 61...L 2322 791 6....L --- paper tape +1% E24 / E96 2512 (6432) 1W +5% E24 blister tape paper tape For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number. Phycomp CTC ordering code - Traditional type - North America Regional code for ordering Phycomp branded products. Please see page 12 for details. 59 Resistor Chip Selection Charts Introduction to trimmable chip resistors Features * Reduced size of final equipment * Low assembly costs * Higher component and equipment reliability * Improved performance at high frequency * Low noise, when not trimmed Derating curve Construction Maximum dissipation (P) in percentage of rated power as a function of the operating ambient temperature (Tamb). Primary glass layer 70 100 Rated Power (%) Resistor (RuO2) (Jumper chip is a conductor) 80 60 TR0805TR1206 40 TR0402TR0603 20 155 125 -55 -40 -20 0 20 40 60 80 100 120 External electrode (matte Tin) Alumina Substrate 140 160 Internal Electrode (Ag-Pd) Secondary Electrode (Nickel plated) Ambient Temperature (C) Dimensions I1 I1 H I2 I2 L 60 W unit: mm Type L W H I1 I2 TR0402 1.00 0.10 0.50 0.05 0.35 0.05 0.20 0.10 0.25 0.10 TR0603 1.60 0.10 0.80 0.10 0.45 0.10 0.25 0.15 0.25 0.15 TR0805 2.00 0.10 1.25 0.10 0.50 0.10 0.35 0.20 0.35 0.20 TR1206 3.10 0.10 1.60 0.10 0.55 0.10 0.45 0.20 0.40 0.20 Resistor Chip Selection Charts Introduction to trimmable chip resistors Electrical characteristics Type Power P70 Operating Temp. range TR0402 1/16W -55C to +125C 50V 100V 100V TR0603 1/16W -55C to +125C 50V 100V 100V TR0805 1/8W -55C to +155C 150V 300V 500V TR1206 1/4W -55C to +155C 200V 500V 500V MWV RCOV DWV T. C. R. ( ppm/C) Resistance range & tolerance 10 < R 1M 100 E24 +0/-10%, +0/-20%, +0/-30% 1 R 10M 1 R 10 200 1M < R 10M Environmental characteristics Performance test Test method Procedure Requirements Life MIL-STD-202Gmethod 108A 1 000 hours at 70 5C applied RCWV 1.5 hours on, 0.5 hours off, still air required (2% +0.05) High temperature exposure MIL-STD-202Gmethod 108A 1 000 hours at maximum operating temperature depending on specification, unpowered (1% +0.05) Moisture resistance MIL-STD-202Gmethod 106F Each temperature / humidity cycle is defined at 8 hours (method 106F), 3 cycles / 24 hours for 10d with 25C / 65C 95% R.H (2% +0.05) Thermal shock MIL-STD-202Gmethod 107G LCT / UCT, number of cycles required is 300 Maximum transfer time is 20 seconds (0.5% +0.05) for 10K to 10M (1% +0.05) for others Wetting IPC/JEDECJSTD-002B testB Electrical test not required. Magnification 50X Leadfree solder bath at 245 3C Dipping time: 3 0.5 seconds Well tinned (95% covered) Resistance to soldering heat MIL-STD-202Gmethod 210F Leadfree solder, 270C, 10 seconds immersion time (1% +0.05) MIL-R-55342Dpara 4.7.5 2.5 times RCWV or maximum overload voltage whichever is less for 5 seconds at room temperature (2% +0.05) Solderability Short time overload 61 Resistor Chip Selection Charts 0402 to 1206 Trimmable / TR series Size: inch (mm) 0402 (1005) 0603 (1608) 0805 (2012) 1206 (3216) Power P70 1/16W 1/16W 1/8W 1/4W 0/-10% 0/-20% 0/-30% 0/-10% 0/-20% 0/-30% 0/-10% 0/-20% 0/-30% 0/-10% 0/-20% 0/-30% Tolerance (Trimma (Trimma (Trimma (Trimma (Trimma (Trimma (Trimma (Trimma (Trimma (Trimma (Trimma (Trimma ble) ble) ble) ble) ble) ble) ble) ble) ble) ble) ble) ble) Resistance Range E24 E24 E24 E24 E24 E24 E24 E24 E24 E24 E24 E24 1 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 1 k 1.5 k 2.2 k 3.3 k 4.7 k 6.8 k 10 k 15 k 22 k 33 k 47 k 68 k 100 k 150 k 220 k 330 k 470 k 680 k 1 M 1.5 M 2.2 M 3.3 M 4.7 M 6.8 M 10 M Remark Note: 1. Value in "Resistance" means the minimum one 2. Products with lead free terminations meet RoHS requirements. None of the forbidden materials are used in products / production. The Pb-glass contained in electrodes, resistor element and glass is exempted by RoHS. 62 Resistor Chip Selection Charts 0402 to 1206 Global part number - Preferred type for ordering Yageo / Phycomp branded products Ordering example: TR0603MR-07100K(L) TR M R 0603 07 100K (L) Optional code(1/2) (code 17) Series name (code 1-2) TR = Trimmable Resistance (code 12-16) 10R = 10 100R = 100 100K = 100K Size code (code 3-6) (inch / metric) 0402 = 1.0 x 0.5 0603 = 1.6 x 0.8 0805 = 2.0 x 1.25 1206 = 3.2 x 1.6 Taping reel (code 10-11) 07 = 7 inch Dia. reel Tolerance (code 7) K = 0/-10% M = 0/-20% N = 0/-30% T. C. R. (code 9) "" = Based on spec. ( for thick film only) Packing style (code 8 ) R = Paper tape reel Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process" 2. On customized label. "LFP" or specific symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request) Phycomp world wide - Traditional type Size: inch (mm) Power Tolerance Resistance Packing Quantity 5 000 0/-20% 5 000 0/-30% Europe 5 000 0402 (1005) 1/16 W E24 paper tape Trimmable chip resistors 0603 (1608) 1/10 W E24 paper tape 0805 (2012) 1/8 W E24 paper tape 1206 (3216) 1/4 W E24 paper tape 2350 503 21...L 2350 502 11...L 2350 501 11...L 2350 500 11...L 2350 503 20...L 2350 502 10...L 2350 511 10...L 2350 500 10...L on request on request on request 2322 724 94...L 2322 792 61...L 2322 793 6....L 2322 791 6....L --- For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number. Phycomp CTC ordering code - Traditional type - North America Regional code for ordering Phycomp branded products. Please see page 12 for details. 63 Resistor Chip Selection Charts Introduction to current sensors - low TCR chip resistors Features * Excellent TCR compare to thick film low ohmic * Precision current sensing control * Excellent performance for current sensing applicatIons * Ultra low ohmic down to 0.001 Derating curve Construction PR series Maximum dissipation (P) in percentage of rated power as a function of the operating ambient temperature (Tamb). PF / PT series protective coat resistive layer inner electrode termination ceramic substrate metal substrate end termination H H protective coat I1 I2 70 Rated Power (%) 100 80 60 40 -40 -20 0 20 40 60 80 100 120 R005 W 155 125 -55 I1 end termination W PT0402 to PT1206 PT2010 20 protective coat protective coat marking I2 PR2010 PR2512 PF2512 PT1218 PT2512 140 160 L L Ambient Temperature (C) Construction will be adjusted to resistance value Dimensions PR seriytts Type PR2010 PR2512 Resistance range 2 m - 6 m 1 m - 2 m 3 m - 5 m L 5.10 0.20 6.30 0.20 6.30 0.20 W 2.50 0.20 3.20 0.20 3.20 0.20 H 0.55 0.20 0.75 0.15 0.55 0.15 l1 0.75 0.20 1.20 0.20 0.60 0.20 l2 0.75 0.20 1.20 0.20 0.60 0.20 L W H l1 6.50 0.25 3.15 0.25 0.60 0.25 1.00 0.25 l2 1.75 0.25 0.60 0.25 H 0.35 0.05 0.45 0.10 0.50 0.10 0.55 0.10 0.50 0.10 0.55 0.10 0.55 0.10 0.55 0.10 l1 0.20 0.10 0.25 0.15 0.35 0.20 0.45 0.20 0.50 0.20 0.45 0.25 0.60 0.20 0.60 0.20 Note: For relevant physical dimensions, please refer to above construction outlines PF series Type PF2512 Resistance range 6 m - 14 m 15 m - 130 m Note: For relevant physical dimensions, please refer to above construction outlines Please contact with sales offices, distributors and representatives in your region before order PT series Type PT0402 PT0603 PT0805 PT1206 PT1210 PT1218 PT2010 PT2512 Resistance range 100 m - 910 m L 1.00 0.10 1.60 0.10 2.00 0.10 3.10 0.10 3.10 0.10 3.05 0.15 5.00 0.10 6.35 0.10 W 0.50 0.05 0.80 0.10 1.25 0.10 1.60 0.10 2.60 0.15 4.60 0.10 2.50 0.15 3.20 0.15 Note: For relevant physical dimensions, please refer to above construction outlines Please contact with sales offices, distributors and representatives in your region before order 64 l2 0.25 0.10 0.25 0.15 0.35 0.20 0.45 0.20 0.50 0.20 0.50 0.25 0.50 0.20 0.50 0.20 Resistor Chip Selection Charts Introduction to current sensors - low TCR chip resistors Electrical characteristics Type Power P70 PR2010 0.5W PR2512 1W PF2512 1W Power enhancement PR2010 1W Power enhancement PR2512 2W Power enhancement PF2512 2W PT0402 1/16W PT0603 1/10W PT0805 1/8W PT1206 1/4W PT1210 1/2W Operating Temp. range Max. working voltage Tolerance Resistance range & T. C. R. 2m R 6m 150 ppm/C 1m R 2m 200 ppm/C 3m R 5m 100 ppm/C -55C to +155C 6m R 130m 100 ppm/C 1%, 2%, 5% (E24 ) 2m R 6m 150 ppm/C 1m R 2m 200 ppm/C 3m R 5m 100 ppm/C -55C to +155C 6m R 130m 100 ppm/C (P x R)^1/2 200 ppm/C -55C to +125C 1%, 5% (E24) PT1218 1W -55C to +155C PT2010 3/4W -55C to +125C PT2512 1W -55C to +155C 100m R 910m 100 ppm/C Environmental characteristics Performance test Test method Procedure Requirements Life MIL-STD-202Gmethod 108A 1 000 hours at 70 5C applied RCWV 1.5 hours on, 0.5 hours off, still air required (1% +0.0005) High temperature exposure MIL-STD-202Gmethod 108A 1 000 hours at maximum operating temperature depending on specification, unpowered (1% +0.0005) Moisture resistance MIL-STD-202Gmethod 106F Each temperature / humidity cycle is defined at 8 hours (method 106F), 3 cycles / 24 hours for 10d with 25C / 65C 95% R.H (0.5% +0.0005) Thermal shock MIL-STD-202Gmethod 107G LCT / UCT, number of cycles required is 300 Maximum transfer time is 20 seconds (0.5% +0.0005) Wetting IPC/JEDECJSTD-002B testB Electrical test not required. Magnification 50X Leadfree solder bath at 245 3C Dipping time: 3 0.5 seconds Well tinned (95% covered) Resistance to soldering heat MIL-STD-202Gmethod 210F Leadfree solder, 270C, 10 seconds immersion time (0.5% +0.0005) MIL-R-55342Dpara 4.7.5 2.5 times RCWV or maximum overload voltage whichever is less for 5 seconds at room temperature (0.5% +0.0005) Solderability Short time overload 65 Resistor Chip Selection Charts Standard type, PR2010 / PR2512 / PF2512 / PT0402 to 2512 Current sensors - Low TCR Series PR / PF / PT series Size: inch (mm) 2512 (6432) Power P70 1W Tolerance 5% 1% Resistance Range E24 E24 0.0010 0.0020 0.0030 0.0040 0.0050 0.0060 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 Remark Note: For sizes of PR2010 and PT0402 to 2512, please contact with sales offices, distributors and representatives in your region before order 66 Resistor Chip Selection Charts Standard type, PR2010 / PR2512 / PF2512 / PT0402 to 2512 Global part number - Preferred type Ordering example: PF2512FKF070R01(L) PF 2512 F K F 07 0R01 (L) Optional code(1/2) (code 17) Series name (code 1-2) PT / PR / PF = Current sensor - low TCR Resistance (code 12-16) 0R01 = 0.01 0R1 = 0.1 0R2 = 0.2 Size code (code 3-6) (inch / metric) 0402 = 1.0 x 0.5 0603 = 1.6 x 0.8 0805 = 2.0 x 1.25 1206 = 3.2 x 1.6 2010 = 5.0 x 2.5 2512 = 6.35 x 3.2 Taping reel (code 10-11) 07 = 7 inch Dia. reel 7W = 7 inch Dia. reel and 2 x standard power type Tolerance (code 7) F = 1% G = 2% J = 5% (for Jumper ordering) T. C. R. (code 9) M = 75 ppm/C F = 100 ppm/C L = 150 ppm/C G = 200 ppm/C Packing style (code 8 ) R = Paper tape reel K = Embossed plastic tape reel Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process" 2. On customized label. "LFP" or specific symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request) 3. PT series products are available by "Global part number" only Phycomp world wide - Traditional type Current Sensor - Low TCR / PR series Size: inch (mm) 2010 (5025) 2512 (6432) Power 1/2 W 1W 1W 2W Tolerance +5% +1% +5% +1% +5% +1% +5% +1% Packing blister tape blister tape Quantity 4 000 2322 760 63..0L 2322 761 11.. 0L 2322 760 65.. 0L 2322 761 13.. 0L 2322 762 94..0L 2322 763 95..0L 2322 762 10..0L 2322 763 10..0L ----------------5 000 For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number. Phycomp world wide - Traditional type Size: inch (mm) Power Tolerance Packing Quantity 4 000 5 000 Current Sensor - Low TCR / PF series 2512 (6432) 1W +5% 2W +1% +5% +1% blister tape 2322 764 96..L 2322 764 97..L 2322 764 10..L 2322 764 30..L --- --- --- --- For ordering rules: See page 13 for E24 / E96 values and the last 4 or 3 digits of the 12NC catalogue number. Phycomp CTC ordering code - Traditional type - North America Regional code for ordering Phycomp branded products. Please see page 12 for details. 67 Resistor Chip Selection Charts Introduction to RF attenuator chip resistors Features * Mobile phone * Receivers * Battery charger * Palmtop computers * PDAs Derating curve Construction Maximum dissipation (P) in percentage of rated power as a function of the operating ambient temperature (Tamb). ATV 321 The rectangular marker designates input pin 1 1 3 1 3 70 100 Rated Power (%) Schematics 80 R1 attenuated output signal input signal 60 R2 R2 40 20 2 125 -55 -40 -20 0 20 40 60 80 100 120 140 2 160 4 4 Ambient Temperature (C) Dimensions L P A B T D W unit: mm 68 Type L W T A B P D ATV321 1.00 0.10 1.00 0.10 0.35 0.05 0.33 0.10 0.15 0.10 0.65 0.10 0.25 0.10 Resistor Chip Selection Charts Introduction to RF attenuator chip resistors Electrical characteristics Type Power P70 Operating Temp. range MPV VSWR (Max.) Impedance Resistance range & tolerance 1DB - 5DB 0.3 dB ATV321 40mW -55C to +125C 50V 1.3 50 6DB - 10DB 0.5 dB 15DB 1.0 dB 20DB 2.0 dB Frequency range 1DB - 10DB DC to 2.5 GHz 15DB - 20DB DC to 2.0 GHz Environmental characteristics Performance test Test method Procedure Requirements Life MIL-STD-202Gmethod 108A 1 000 hours at 70 5C applied RCWV 1.5 hours on, 0.5 hours off, still air required Max.: 0.3 dB Humidity (steady state) JIS C 5202 7.5 1 000 hours, 40 2C, 93(+2/-3)% RH RCWV applied for 1.5 hours on and 0.5 hour off Max.: 0.3 dB Moisture resistance MIL-STD-202Gmethod 106F Each temperature / humidity cycle is defined at 8 hours (method 106F), 3 cycles / 24 hours for 10d with 25C / 65C 95% R.H Max.: 0.3 dB Thermal shock MIL-STD-202Gmethod 107G LCT / UCT, number of cycles required is 300 Maximum transfer time is 20 seconds Max.: 0.3 dB Wetting IPC/JEDECJSTD-002B testB Electrical test not required. Magnification 50X Leadfree solder bath at 245 3C Dipping time: 3 0.5 seconds Well tinned (95% covered) Resistance to soldering heat MIL-STD-202Gmethod 210F Leadfree solder, 270C, 10 seconds immersion time Max.: 0.1 dB MIL-R-55342Dpara 4.7.5 2.5 times RCWV or maximum overload voltage whichever is less for 5 seconds at room temperature Max.: 0.3 dB Solderability Short time overload 69 Resistor Chip Selection Charts 0404 Global part number - Preferred type for ordering Yageo / Phycomp branded products Ordering example: ATV321BR-071DB(L) AT V321 B R 07 1DB (L) Optional code(1/2) (code 16) Series name (code 1-2) AT = RF attenuator thick film Attenuation (code 12-15) 0DB 1DB 2DB 10DB 15DB 20DB Size code (code 3-6) (inch / metric) V321 = 0404 = 1.0 x 1.0 Tolerance (code 7) C = 0.3dB D = 0.5dB F = 1dB G = 2dB Taping reel (code 10-11) 07 = 7 inch Dia. reel Packing style (code 8 ) R = Paper tape reel T. C. R. (code 9) "" = Based on spec. ( for thick film only) Note: 1. All our RSMD products meet RoHS Compliant. "LFP" of the internal 2D reel label mentions "Lead Free Process" 2. On customized label. "LFP" or specific symbol printed and the optional "L" at the end of CTC/12NC can be added (both are on customer request) Phycomp world wide - Traditional type Packing Quantity 10 000 Remark paper tape 2350 703 11...L For last three digits, see table of Attenuation codes below Note: L = An optional code Phycomp CTC ordering code - Traditional type - North America Packing Quantity 10 000 Remark paper tape 9CV3218AXXXXX-PF3 For last 9th to 13th digits, see table of Attenuation codes below Attenuation codes Standard 70 Value (dB) Tolerance (dB) Phycomp world wide code (12NC) Phycomp North America code (NA code) 1 2 3 4 5 6 7 8 9 10 15 20 0.3 0.3 0.3 0.3 0.3 0.5 0.5 0.5 0.5 0.5 1.0 2.0 012 022 032 042 052 063 073 083 093 103 154 205 01DBC 02DBC 03DBC 04DBC 05DBC 06DBD 07DBD 08DBD 09DBD 10DBD 15DBF 20DBG Resistor Chip Engineering Design Kits Engineering design kits Thick film chip resistors Global CTC (Preferred) RC0201-R-SKE24L RC0402JR-SKE24L RC0402FR-SKE96L RC0603JR-SKE24L RC0603FR-SKE96L RC0805JR-SKE24L RC0805FR-SKE96L RC1206JR-SKE24L RC1206FR-SKE96L Description 0201, 1% & 5% , RoHS compliant, + Jumper 0402, 5%, RoHS compliant, + Jumper 0402, 1%, RoHS compliant, + Jumper 0603, 5%, RoHS compliant, + Jumper 0603, 1%, RoHS compliant, + Jumper 0805, 5%, RoHS compliant, + Jumper 0805, 1%, RoHS compliant, + Jumper 1206, 5%, RoHS compliant, + Jumper 1206, 1%, RoHS compliant, + Jumper Size Tolerance Max. power Resistance range 0201 0402 0402 0603 0603 0805 0805 1206 1206 F/J J F J F J F J F 1/20 W 1/16 W 1/16 W 1/10 W 1/10 W 1/8 W 1/8 W 1/4 W 1/4 W 10 - 1M 10 - 1M 10 - 1M 10 - 1M 10 - 1M 10 - 1M 10 - 1M 10 - 1M 10 - 1M Size Tolerance Max. power Resistance range 0402 X 2 0402 X 4 J 1/16 W 10 - 1M Resistor Min. pieces items 100 100 100 50 50 50 50 50 50 120 110 450 110 450 110 280 110 350 Thick film array chip resistors (convex) Global CTC (Preferred) YC12X-JR-SK001L Description YC124 / YC122, 5%, +Jumper, RoHS compliant, refer to below table Global CTC YC122-JR-070RL YC122-JR-0710RL YC122-JR-0722RL YC122-JR-0733RL YC122-JR-0747RL YC122-JR-07100RL YC122-JR-07330RL YC122-JR-07470RL YC122-JR-071KL YC122-JR-072K2L YC122-JR-073K3L YC122-JR-074K7L YC122-JR-0710KL Description 2R - Array series 0404, 5%, 1/16W 0404, 5%, 10R, 1/16W 0404, 5%, 22R, 1/16W 0404, 5%, 33R, 1/16W 0404, 5%, 47R, 1/16W 0404, 5%, 100R, 1/16W 0404, 5%, 330R, 1/16W 0404, 5%, 470R, 1/16W 0404, 5%, 1K, 1/16W 0404, 5%, 2K2, 1/16W 0404, 5%, 3K3, 1/16W 0404, 5%, 4K7, 1/16W 0404, 5%, 10K, 1/16W Q'ty Resistor Min. pieces items 100 Global CTC Description 4R - Array series YC124-JR-070RL 0408, Jumper, 1/16W YC124-JR-0710RL 0408, 5%, 10R, 1/16W YC124-JR-0722RL 0408, 5%, 22R, 1/16W YC124-JR-0733RL 0408, 5%, 33R, 1/16W YC124-JR-0747RL 0408, 5%, 47R, 1/16W YC124-JR-07100RL 0408, 5%, 100R, 1/16W YC124-JR-07330RL 0408, 5%, 330R, 1/16W YC124-JR-07470RL 0408, 5%, 470R, 1/16W YC124-JR-071KL 0408, 5%, 1K, 1/16W YC124-JR-072K2L 0408, 5%, 2K2, 1/16W YC124-JR-073K3L 0408, 5%, 3K3, 1/16W YC124-JR-074K7L 0408, 5%, 4K7, 1/16W YC124-JR-0710KL 0408, 5%, 10K, 1/16W 100 100 100 100 100 100 100 100 100 100 100 100 100 75 Q'ty 100 100 100 100 100 100 100 100 100 100 100 100 100 Engineering design kit for current sensing application Global CTC (Preferred) CS0402-R-SK001L Description 0402 - 2512, 1% & 5%, RoHS compliant Size Tolerance Max. power Resistance range 0402 - 2512 F/J --- 100m - 910m Resistor Min. pieces items 30 160 Engineering design kit for mobil application Global CTC (Preferred) Description Size Tolerance Max. power Resistance range MD0402-R-SK001L Chip resistors / MLCC / Attenuators, refer to below table --- --- --- --- Global CTC RL0805FR-070R36L RL0805FR-070R4L RL0805FR-070R62L RL0805FR-7W0R2L RL0805FR-7W0R22L RL0805FR-7W0R33L RL0805FR-7W0R36L RL0805FR-7W0R39L RC0805FR-7W1RL Description Low ohmic series 0805, 1%, 0R36, 1/8W 0805, 1%, 0R4, 1/8W 0805, 1%, 0R62, 1/8W 0805, 1%, 0R2, 1/4W 0805, 1%, 0R22, 1/4W 0805, 1%, 0R33, 1/4W 0805, 1%, 0R36, 1/4W 0805, 1%, 0R39, 1/4W 0805, 1%, 1R, 1/4W Q'ty 50 50 50 50 50 50 50 50 50 Global CTC Resistor Min. pieces items 50 - 100 Description C - Array series CA0508KRNPO9BN100 0508, 10%, 10pF, NP0, 50V CA0508KRNPO9BN150 0508, 10%, 15pF, NP0, 50V CA0508KRNPO9BN180 0508, 10%, 18pF, NP0, 50V CA0508KRNPO9BN220 0508, 10%, 22pF, NP0, 50V CA0508KRNPO9BN330 0508, 10%, 33pF, NP0, 50V Attenuiator series ATV321CR-071DBL 0404, 0.3dB, 1dB ATV321CR-073DBL 0404, 0.3dB, 3dB ATV321CR-075DBL 0404, 0.3dB, 5dB ATV321CR-076DBL 0404, 0.3dB, 6dB 44 Q'ty 50 50 50 50 50 30 30 30 30 Note: Before ordering, please contact with sales force for detail of resistance 71 SMD CERAMIC MILTILAYER CAPACITORS MLCC General Information Specification overview Specification overview Description TC code Series C-Arrays High frequency 74 Size 0.22 pF to 33 nF 16 V to 25 V 0201, 0402, 0603, 0805, 1206, 1210 General purpose 0.22 pF to 390 pF 50 V 0201, 0402, 0603, 0805, 1206, 1210, 1812 10 pF to 22 nF 100 V to 630 V 0603, 0805, 1206, 1210, 1808, 1812 High voltage 10 pF to 2.7 nF 1 kV, 2 kV, 3 kV, 4 kV 1206, 1210, 1808, 1812 Microwave 0.47 pF to 120 pF 50 V 0603, 0805, 1206 General purpose & High capacitance 100 pF to 22 F 6.3 V to 50 V 0201, 0402, 0603, 0805, 1206, 1210, 1812 X7R Medium voltage Safety certification product Voltage range General purpose NP0 Medium voltage Discrete Capacitance range 100 pF to 470 nF 100 V to 630 V 0603, 0805, 1206, 1210, 1808, 1812 High voltage 100 pF to 33 nF 1 kV to 3 kV 1206, 1210, 1808, 1812 Low inductance 10 nF to 220 nF 10 V to 50 V 0306, 0508, 0612 X5R General purpose & High capacitance 10 nF to 100 F 6.3 V to 50 V 0201, 0402, 0603, 0805, 1206, 1210, 1812 Y5V General purpose & High capacitance 10 nF to 47 F 6.3 V to 50 V 0201, 0402, 0603, 0805, 1206, 1210 NP0 High voltage SC type 10 pF to 1 nF X1/Y2, X2/Y3 1808, 1812 X7R High voltage SC type 150 pF to 1.5 nF X1/Y2, X2/Y3 1808, 1812 NP0 4-C arrays 10 pF to 1 nF 50 V 0508, 0612 2-C arrays 10 nF to 100 nF 16 V 0405 4-C arrays 220 pF to 100 nF 16 V to 50 V 0508, 0612 Y5V 4-C arrays 10 nF to 100 nF 25 V 0508, 0612 NP0 High frequency 0.22 pF to 10 pF 50 V 0402, 0603 X7R MLCC General Information Case dimensions Case dimensions Discrete capacitors Case size designation Dimensions in mm Inch-based Metric L1 W 0201 0603M 0.6 0.03 0.3 0.03 L2 / L3 0.10 L2 / L3 0.20 0.20 0402 1005M 1.0 0.05 0.5 0.05 0.20 0.30 0.40 0603 1608M 1.6 0.10 0.8 0.07 0.20 0.60 0.40 0805 2012M 2.0 0.10 1.25 0.10 0.25 0.75 0.55 1206 3216M 3.2 0.15 1.6 0.15 0.25 0.75 1.40 1210 3225M 3.2 0.20 2.5 0.20 0.25 0.75 1.40 1808 4520M 4.5 0.40 2.0 0.30 0.25 0.75 2.20 1812 4532M 4.5 0.20 3.2 0.20 0.25 0.75 2.20 min L4 max min W L2 L4 L1 L3 Discrete capacitors - High voltage SC type / Case size designation W L2 L4 L1 L3 Dimensions in mm Inch-based Metric L1 W L2 / L3 L2 / L3 1808 4520M 4.8 0.30 2.0 0.30 0.25 0.75 3.20 1812 4532M 4.8 0.30 3.2 0.30 0.25 0.75 4.00 min L4 max min 2-C arrays Case size designation F Demensions in mm Inch-based Metric L W Tmin Tmax A B P 0405 (2 x 0402) 1013M (2 x 1005) 1.37 0.15 1.0 0.15 0.5 0.7 0.36 0.1 0.2 0.1 0.64 0.1 W B T A P L 4-C arrays Case size designation B W L A Dimensions in mm Inch-based Metric L W Tmin Tmax A B P 0508 (4 x 0402) 1220M (4 x 1005) 2.0 0.15 1.25 0.15 0.50 0.70 0.28 0.10 0.2 0.10 0.5 0.10 0612 (4 x 0603) 1632M (4 x 1608) 3.2 0.15 1.60 0.15 0.70 0.90 0.4 0.10 0.3 0.20 0.8 0.10 P T Discrete capacitors - Low inductance types only Case size designation W T L2 L4 L1 L3 Inch-based Metric 0306 0508 0612 Dimensions in mm L1 W T L2 / L3 0816M 0.8 0.15 1.6 0.20 0.50 0.10 0.10 0.30 0.20 1220M 1.25 0.20 2.0 0.20 0.85 0.10 0.13 0.46 0.38 1632M 1.6 0.20 3.2 0.20 0.85 0.10 0.13 0.46 0.50 min L2 / L3 max L4 min 75 MLCC General Information Ordering Information - Global part number Global part number Ordering example: CC0201KRX7R8BB102 CC 0201 Series name (code 1-2) CA = 4 x Capacitance array CB = 2 x Capacitance array CC = Multilayer chip capacitance CL = Low inductance capacitance CM = Micro-wave capacitance CH = High frequency SC = Safety certification capacitance Size code (code 3-6) 0201 0402 0603 0805 1206 1210 1808 1812 0306 0405 0508 0612 Capacitance tolerance (code 7) B = 0.1 pF C = 0.25 pF D = 0.5 pF F = 1% G = 2% J = 5% K = 10% M = 20% Z = -20% to +80% Packing style (code 8) R = Paper tape reel O7 inch P = Paper tape reel O13 inch K = Embossed plastic tape reel O7 inch F = Embossed plastic tape reel O13 inch TC material (code 9-11) NP0 X5R X7R Y5V 76 K R X7R 8 B B 102 Capacitance value (code 15-17) 102 = 1 000 pF (2 significant digits+number of zeros; the 3rd digit signifies the multiplying factor, and letter R is decimal point) 0=x1 1 1 = x 10 2 2 = x 10 3 3 = x 10 4 4 = x 10 5 5 = x 10 6 6 = x 10 7 7 = x 10 X X R = Special capacitance (X X: capacitance before decimal point) Process code (code 14) N = NP0 B = Class 2 product Termination (code 13) B = Ni-Barrier Rated voltage (code 12) 4 =4V 5 = 6.3 V 6 = 10 V 7 = 16 V 8 = 25 V 9 = 50 V 0 = 100 V A = 200 V B = 500 V C = 1 kV D = 2 kV E = 3 kV G = 35 V H = 4 kV S = 2.5 kV T = X2 / Y3 W = X1 / Y2 Y = 250 V Z = 630 V MLCC General Information Ordering information for North America Phycomp CTC ordering code - Noth America Ordering example: 02012R102K8B20D 0201 2R Size Temperature code characteristic 0201 0402 0603 0805 1206 1210 1808 1812 0306 0405 0508 0612 CG = NP0 2B = X5R 2R = X7R 2F = Y5V 102 K 8 B 2 0 0 Capacitance (pF) Tolerance Voltage Termination Packing Marking Range identifier 102 = 1 000 pF The third digit signifies the multiplying factor: 8 = x 0.01 9 = x 0.1 0=x1 1 = x 10 2 = x 100 3 = x 1 000 4 = x 10 000 5 = x 100 000 6 = x 1 000 000 7 = x 10 000 000 B = 0.1 pF C = 0.25 pF D = 0.5 pF F = 1% G = 2% J = 5% K = 10% M = 20% Z = -20% to +80% 5 = 6.3 V B = NiSn 6 = 10 V 7 = 16 V 8 = 25 V 9 = 50 V 0 = 100 V B = 200 V C = 250 V D = 500 V E = 1 kV F = 2 kV G = 3 kV H = 4 kV Z = 630 V S = 2.5 kV T = X2/Y3 W = X1/Y2 2 = 180mm / 7" paper 0 = No marking 3 = 330 mm / 13" paper B = 180mm / 7" blister F = 330 mm / 13" blister P = Bulk case 0 = Conventional ceramic D = Class 2 MLCC L = Low inductance M = Microwave S = Safty certification capacitance 77 MLCC General Information Thickness classes and packing quantities for all series Thickness classes and packing quantities Description Thickness classification (mm) Paper Blister Paper Blister 0201 0.3 0.03 15 000 --- 50 000 --- --- 0402 0.5 0.05 10 000 --- 50 000 --- 50 000 0603 0.8 0.1 4 000 --- 15 000 --- 15 000 0.6 0.1 4 000 --- 20 000 --- 10 000 0.85 0.1 4 000 --- 15 000 --- 8 000 1.25 0.2 --- 3 000 --- 10 000 5 000 0805 1206 1210 1808 Tape width --- 20 000 --- --- 4 000 --- 15 000 --- --- 1.00 / 1.15 0.1 --- 3 000 --- 10 000 --- 1.25 0.2 --- 3 000 --- 10 000 --- --- 2 500 --- 10 000 --- 1.6 0.2 8 mm --- 2 000 --- 10 000 --- 0.6 / 0.7 0.1 --- 4 000 --- 15 000 --- 0.85 0.1 --- 4 000 --- 10 000 --- 1.15 0.1 --- 3 000 --- 10 000 --- 1.15 0.15 --- 3 000 --- 10 000 --- 1.25 0.2 --- 3 000 --- --- --- 1.5 0.1 --- 2 000 --- --- --- 1.6 / 1.9 0.2 --- 2 000 --- --- --- 2.0 0.2 --- 2 000 / 1 000 --- --- --- 2.5 0.2 --- 1 000 / 500 --- --- --- 1.15 0.15 --- 3 000 --- --- --- 1.25 0.2 --- 3 000 --- --- --- 1.35 0.15 --- 2 000 --- --- --- 1.5 0.1 --- 2 000 --- --- --- 1.6 0.2 --- 2 000 --- --- --- --- 2 000 --- --- --- --- 2 000 --- --- --- 12 mm 1.15 0.1 --- 1 500 --- --- --- 1.15 0.15 --- 1 500 --- --- --- 1.35 0.15 --- 1 000 --- --- --- 1.5 0.1 --- 1 000 --- --- --- 1.6 0.2 --- 1 000 --- --- --- 2.0 0.2 --- 1 000 --- --- --- 0306 0.5 0.1 4 000 --- 15 000 --- --- 0508 0.85 0.1 4 000 --- 15 000 --- --- 0612 0.85 0.1 4 000 --- 15 000 --- --- 0405 0.6 0.1 4 000 --- --- --- --- 0508 0.6 0.1 4 000 --- --- --- --- 0612 0.8 0.1 4 000 --- --- --- --- 1812 78 Quantity per bulk case 4 000 2.0 0.2 Arrays 330 mm / 13" 0.6 0.1 0.6 / 0.85 0.1 Low inductance 180 mm / 7" 0.85 0.1 1.6 0.15 Discrete capacitors Quantity per reel Size code 8 mm MLCC Selection Charts NP0 - General purpose 16 to 25V, 0201 to 0603 NP0 General purpose Capacitance Last 2-digit of 12NC 10 pF 12 pF 15 pF 18 pF 22 pF 27 pF 33 pF 39 pF 47 pF 56 pF 68 pF 82 pF 100 pF 120 pF 150 pF 180 pF 220 pF 270 pF 330 pF 390 pF 470 pF 560 pF 680 pF 820 pF 1000 pF 1.2 nF 1.5 nF 1.8 nF 2.2 nF 2.7 nF 3.3 nF Tape width 23 24 25 26 27 28 29 31 32 33 34 35 36 37 38 39 41 42 43 44 45 46 47 48 49 51 52 53 54 55 56 0201 25V 0402 16V 0603 25V 16V 25V 0.5 0.05 0.3 0.03 0.5 0.05 0.8 0.1 0.8 0.1 8 mm Note: Values in shaded cells indicate thickness class (unit: mm) 79 MLCC Selection Charts NP0 - General purpose 16 to 25V, 0805 to 1210 NP0 General purpose Capacitance Last 2-digit of 12NC 3.3 nF 3.9 nF 4.7 nF 5.6 nF 6.8 nF 8.2 nF 10 nF 12 nF 15 nF 18 nF 22 nF 27 nF 33 nF Tape width 56 57 58 59 61 62 63 64 65 66 67 68 69 0805 16V 25V 16V 1210 25V 25V 1.25 0.2 1.25 0.2 Note: Values in shaded cells indicate thickness class (unit: mm) 80 1206 1.25 0.2 1.25 0.2 1.25 0.2 1.6 0.2 2.0 0.2 1.6 0.2 8 mm MLCC Selection Charts NP0 - General purpose 16 to 25V, 0201 to 1210 Global part number - Preferred type Global Part Number is the preferred clear text code for ordering Yageo and Phycomp branded products. For details, please see page 76. 12NC ordering code - Phycomp branded product only 22 XX XX X X 1 X Carrier tape 50 = Blister ( 1kV) 22 = Blister 38 = Paper 54 = Bulk Voltage 78 = 16 V 91 = 25 V 60 = 100 V 93 = 200 V 83 = 250 V 97 = 500 V 98 = 630 V 00 = 1 kV 02 = 2 kV 99 = 2.5 kV 04 = 3 kV 50 = 4 kV 52 = X2 / Y3 53 = X1 / Y2 XX Capacitance value See selection chart Tolerance 4 = 2% 5 = 5% 6 = 10% TC material 1 = NP0 Packing 1 = 180 mm / 7" reel 5 = 330 mm / 13" reel 4 = Bulk case Size 8 = 0201 7 = 0402 6 = 0603 0 = 0805 1 = 1206 2 = 1210 3 = 1808 4 = 1812 Phycomp CTC ordering code - North America Regional code for ordering Phycomp branded products. For details, please see page 77. 81 MLCC Selection Charts NP0 - Gerneral purpose 50V, 0201 to 1812 NP0 General purpose Capacitance 0.47 pF 0.56 pF 0.68 pF 0.82 pF 1 pF 1.2 pF 1.5 pF 1.8 pF 2.2 pF 2.7 pF 3.3 pF 3.9 pF 4.7 pF 5.6 pF 6.8 pF 8.2 pF 10 pF 12 pF 15 pF 18 pF 22 pF 27 pF 33 pF 39 pF 47 pF 56 pF 68 pF 82 pF 100 pF 120 pF 150 pF 180 pF 220 pF 270 pF 330 pF 390 pF 470 pF 560 pF 680 pF 820 pF 1000 pF 1.2 nF 1.5 nF 1.8 nF 2.2 nF 2.7 nF 3.3 nF 3.9 nF 4.7 nF 5.6 nF 6.8 nF 8.2 nF 10 nF 82 Last 3-digit of 12NC 477 567 687 827 108 128 158 188 228 278 338 398 478 568 688 828 109 129 159 189 229 279 339 399 479 569 689 829 101 121 151 181 221 271 331 391 471 561 681 821 102 122 152 182 222 272 332 392 472 562 682 822 103 0201 50V 0402 0603 0805 1206 1210 1812 50V 50V 50V 50V 50V 50V 0.5 0.05 0.8 0.1 0.6 0.1 0.6 0.1 0.3 0.03 0.6 0.1 0.6 0.1 0.85 0.1 1.25 0.2 0.85 0.1 1.15 0.1 0.85 0.1 MLCC Selection Charts NP0 - Gerneral purpose 50V, 0201 to 1812 NP0 General purpose Capacitance Last 3-digit of 12NC 12 nF 15 nF 18 nF 22 nF Tape width 123 153 183 223 0201 0402 0603 0805 1206 1210 50V 50V 50V 50V 50V 50V 1812 50V 0.85 0.1 1.15 0.15 8 mm 12 mm Note: Values in shaded cells indicate thickness class (unit: mm) 83 MLCC Selection Charts NP0 - Gerneral purpose 50V, 0201 to 1812 Global part number - Preferred type Global Part Number is the preferred clear text code for ordering Yageo and Phycomp branded products. For details, please see page 76. 12NC ordering code - Phycomp branded product only 22 XX XX X X X XXX Carrier tape 22 = Blister 38 = Paper 54 = Bulk Voltage 86 = 50 V Size 8 = 0201 9 = 0402 7 = 0603 1 = 0805 3 = 1206 2 = 1210 5 = 1812 Phycomp CTC ordering code - North America Regional code for ordering Phycomp branded products. For details, please see page 77. 84 Capacitance value See selection chart Tolerance 4 = 0.1 pF for 0.47 pF C < 5 pF 0.25 pF for 5 pF C < 10 pF 2% for C 10 pF 5 = 0.25 pF for C < 5 pF 0.5 pF for 5 pF C < 10 pF 5% for C 10 pF 8 = 0.1 pF for 5 pF C < 10 pF 1% for C 10 pF Packing 1 = 180 mm / 7" reel 7 = 330 mm / 13" reel 4 = Bulk case MLCC Selection Charts NP0 - Midium voltage, 0603 / 0805 NP0 Medium voltage Capacitance Last 2-digit of 12NC 10 pF 12 pF 15 pF 18 pF 22 pF 27 pF 33 pF 39 pF 47 pF 56 pF 68 pF 82 pF 100 pF 120 pF 150 pF 180 pF 220 pF 270 pF 330 pF 390 pF 470 pF 560 pF 680 pF 820 pF 1000 pF 1.2 nF 1.5 nF 1.8 nF 2.2 nF 2.7 nF 3.3 nF 3.9 nF 4.7 nF Tape width 23 24 25 26 27 28 29 31 32 33 34 35 36 37 38 39 41 42 43 44 45 46 47 48 49 51 52 53 54 55 56 57 58 0603 0805 100V 200V 250V 100V 200V 250V 500V 0.8 0.1 0.8 0.1 0.8 0.1 0.6 0.1 0.6 0.1 0.6 0.1 0.6 0.1 0.85 0.1 0.85 0.1 0.85 0.1 1.25 0.2 1.25 0.2 1.25 0.2 0.8 0.1 0.8 0.1 1.25 0.2 1.25 0.2 0.85 0.1 1.25 0.2 8 mm Note: Values in shaded cells indicate thickness class (unit: mm) 85 MLCC Selection Charts NP0 - Midium voltage, 1206 / 1210 NP0 Medium voltage Capacitance Last 2-digit of 12NC 10 pF 12 pF 15 pF 18 pF 22 pF 27 pF 33 pF 39 pF 47 pF 56 pF 68 pF 82 pF 100 pF 120 pF 150 pF 180 pF 220 pF 270 pF 330 pF 390 pF 470 pF 560 pF 680 pF 820 pF 1000 pF 1.2 nF 1.5 nF 1.8 nF 2.2 nF 2.7 nF 3.3 nF 3.9 nF 4.7 nF 5.6 nF 6.8 nF 8.2 nF 10 nF 12 nF 15 nF Tape width 23 24 25 26 27 28 29 31 32 33 34 35 36 37 38 39 41 42 43 44 45 46 47 48 49 51 52 53 54 55 56 57 58 59 61 62 63 64 65 1206 100V 200V 250V 500V 630V 0.6 0.1 0.6 0.1 0.6 0.1 0.6 0.1 0.8 0.1 100V 200V 250V 500V 0.85 0.1 1.0 0.1 1.25 0.2 1.25 0.2 1.15 0.1 0.85 0.1 0.85 0.1 0.85 0.1 1.15 0.15 0.8 0.1 0.8 0.1 1.25 0.2 1.25 0.2 630V 1.25 0.2 0.6 0.1 1.25 0.2 0.85 0.1 0.85 0.1 1.25 0.2 1.15 0.15 1.15 0.15 0.85 0.1 1.25 0.2 1.15 0.15 0.85 0.1 0.8 0.1 Note: Values in shaded cells indicate thickness class (unit: mm) 86 1210 1.25 0.2 8 mm 1.25 0.2 MLCC Selection Charts NP0 - Midium voltage, 1808 / 1812 NP0 Medium voltage Capacitance Last 2-digit of 12NC 10 pF 12 pF 15 pF 18 pF 22 pF 27 pF 33 pF 39 pF 47 pF 56 pF 68 pF 82 pF 100 pF 120 pF 150 pF 180 pF 220 pF 270 pF 330 pF 390 pF 470 pF 560 pF 680 pF 820 pF 1000 pF 1.2 nF 1.5 nF 1.8 nF 2.2 nF 2.7 nF 3.3 nF 3.9 nF 4.7 nF 5.6 nF 6.8 nF 8.2 nF 10 nF 12 nF 15 nF 18 nF 22 nF Tape width 23 24 25 26 27 28 29 31 32 33 34 35 36 37 38 39 41 42 43 44 45 46 47 48 49 51 52 53 54 55 56 57 58 59 61 62 63 64 65 66 67 1808 100V 200V 250V 1812 500V 630V 100V 200V 250V 500V 630V 1.25 0.2 1.25 0.2 1.25 0.2 0.85 0.1 1.25 0.2 1.25 0.2 1.25 0.2 1.25 0.2 0.6 0.1 1.25 0.2 1.25 0.2 1.25 0.2 1.25 0.2 1.15 0.15 1.25 0.2 1.15 0.15 1.6 0.2 0.85 0.1 0.85 0.1 1.25 0.2 1.15 0.15 1.15 0.15 0.85 0.1 1.15 0.15 12 mm Note: Values in shaded cells indicate thickness class (unit: mm) 87 MLCC Selection Charts NP0 - High voltage, 1206 / 1210 NP0 High voltage Capacitance Last 2-digit of 12NC 10 pF 12 pF 15 pF 18 pF 22 pF 27 pF 33 pF 39 pF 47 pF 56 pF 68 pF 82 pF 100 pF 120 pF 150 pF 180 pF 220 pF 270 pF 330 pF 390 pF 470 pF 560 pF 680 pF 820 pF 1000 pF Tape width 23 24 25 26 27 28 29 31 32 33 34 35 36 37 38 39 41 42 43 44 45 46 47 48 49 1206 1kV 2kV 1kV 2kV 0.8 0.1 1.0 0.1 1.25 0.2 1.25 0.2 1.0 0.1 0.8 0.1 1.25 0.2 1.15 0.15 Note: Values in shaded cells indicate thickness class (unit: mm) 88 1210 8 mm MLCC Selection Charts NP0 - High voltage, 1808 / 1812 NP0 High voltage Capacitance Last 2-digit of 12NC 10 pF 12 pF 15 pF 18 pF 22 pF 27 pF 33 pF 39 pF 47 pF 56 pF 68 pF 82 pF 100 pF 120 pF 150 pF 180 pF 220 pF 270 pF 330 pF 390 pF 470 pF 560 pF 680 pF 820 pF 1000 pF 1.2 nF 1.5 nF 1.8 nF 2.2 nF 2.7 nF Tape width 23 24 25 26 27 28 29 31 32 33 34 35 36 37 38 39 41 42 43 44 45 46 47 48 49 51 52 53 54 55 1808 1812 1kV 2kV 3kV 4kV 1.25 0.2 1.25 0.2 1.15 0.15 1.5 0.1 1kV 2kV 3kV 4kV 1.25 0.2 1.15 0.15 1.5 0.1 1.25 0.2 0.85 0.1 1.6 0.2 2.0 0.2 1.6 0.2 1.15 0.15 1.25 0.2 1.6 0.2 12 mm Note: Values in shaded cells indicate thickness class (unit: mm) 89 MLCC Selection Charts NP0 - Midium & High voltage, 0603 to 1812 Global part number - Preferred type Global Part Number is the preferred clear text code for ordering Yageo and Phycomp branded products. For details, please see page 76. 12NC ordering code - Phycomp branded product only 22 XX XX X X 1 X Carrier tape 50 = Blister ( 1kV) 22 = Blister 38 = Paper 54 = Bulk Voltage 78 = 16 V 91 = 25 V 60 = 100 V 93 = 200 V 83 = 250 V 97 = 500 V 98 = 630 V 00 = 1 kV 02 = 2 kV 99 = 2.5 kV 04 = 3 kV 50 = 4 kV 52 = X2 / Y3 53 = X1 / Y2 Phycomp CTC ordering code - North America Regional code for ordering Phycomp branded products. For details, please see page 77. 90 XX Capacitance value See selection chart Tolerance 4 = 2% 5 = 5% 6 = 10% TC material 1 = NP0 Packing 1 = 180 mm / 7" reel 5 = 330 mm / 13" reel 4 = Bulk case Size 8 = 0201 7 = 0402 6 = 0603 0 = 0805 1 = 1206 2 = 1210 3 = 1808 4 = 1812 MLCC Selection Charts NP0 - High frequency, 0402 / 0603 NP0 High frequency Capacitance Last 2-digit of 12NC 0402 0603 50V 50V 0.47 pF 0.56 pF 0.68 pF 0.82 pF 1 pF 1.2 pF 1.5 pF 1.8 pF 2.2 pF 2.7 pF 3.3 pF 3.9 pF 4.7 pF 5.6 pF 6.8 pF 8.2 pF Tape width 77 67 87 27 08 28 58 88 28 78 38 98 78 68 88 28 0.5 0.05 0.8 0.1 8 mm Note: Values in shaded cells indicate thickness class (unit: mm) 91 MLCC Selection Charts NP0 - High frequency, 0402 / 0603 Global part number - Preferred type Global Part Number is the preferred clear text code for ordering Yageo and Phycomp branded products. For details, please see page 76. 12NC ordering code - Phycomp branded product only 22 XX XX X X X XXX Carrier tape 22 = Blister 38 = Paper 54 = Bulk Voltage 84 = 50 V (for high frequency series) Size 9 = 0402 7 = 0603 Capacitance value See selection chart Tolerance 4 = 0.1 pF for 0.47 pF C < 5 pF 0.25 pF for 5 pF C < 10 pF 2% for C 10 pF 5 = 0.25 pF for C < 5 pF 0.5 pF for 5 pF C < 10 pF 5% for C 10 pF 8 = 0.1 pF for 5 pF C < 10 pF 1% for C 10 pF Packing 1 = 180 mm / 7" reel 7 = 330 mm / 13" reel 4 = Bulk case Phycomp CTC ordering code - North America Regional code for ordering Phycomp branded products. For details, please see page 77. 92 MLCC Selection Charts NP0 - Microwave, 0603 to 1206 NP0 Microwave Capacitance Last 2-digit of 12NC 0603 0805 1206 0.47 pF 0.56 pF 0.68 pF 0.82 pF 1 pF 1.2 pF 1.5 pF 1.8 pF 2.2 pF 2.7 pF 3.3 pF 3.9 pF 4.7 pF 5.6 pF 6.8 pF 8.2 pF 10 pF 12 pF 15 pF 18 pF 22 pF 27 pF 33 pF 39 pF 47 pF 56 pF 68 pF 82 pF 100 pF 120 pF Tape width 05 06 07 08 09 11 12 13 14 15 16 17 18 19 21 22 23 24 25 26 27 28 29 31 32 33 34 35 36 37 50V 50V 50V 0.8 0.1 0.8 0.1 0.8 0.1 8 mm Note: Values in shaded cells indicate thickness class (unit: mm) 93 MLCC Selection Charts NP0 - Microwave, 0603 to 1206 Global part number - Preferred type Global Part Number is the preferred clear text code for ordering Yageo and Phycomp branded products. For details, please see page 76. 12NC ordering code - Phycomp branded product only 22 XX XXX X 1 X XX Carrier tape 38 = Paper 54 = Bulk Size 578 = 0603 574 = 0805 576 = 1206 Packing 1 = 180 mm / 7" reel 5 = 330 mm / 13" reel 4 = Bulk case Phycomp CTC ordering code - North America Regional code for ordering Phycomp branded products. For details, please see page 77. 94 Capacitance value See selection chart Tolerance 0 = 0.1 pF for C < 10 pF 1 = 0.25 pF for C < 10 pF 2 = 0.5 pF for 5 pF C < 10 pF 3 = 1% for C 10 pF 4 = 2% pF for C 10 pF 5 = 5% for C 10 pF MLCC Selection Charts X7R - General purpose, 0201 / 0402 X7R General purpose Capacitance Last 2-digit of 12NC 100 pF 150 pF 220 pF 330 pF 470 pF 680 pF 1000 pF 1.5 nF 2.2 nF 3.3 nF 4.7 nF 6.8 nF 10 nF 15 nF 22 nF 33 nF 47 nF 68 nF 100 nF Tape width 09 12 14 16 18 21 23 25 27 29 32 34 36 38 41 43 45 47 49 0201 6.3V 10V 0402 16V 25V 6.3V 10V 0.3 0.03 16V 25V 50V 0.5 0.05 0.5 0.05 0.5 0.05 0.3 0.03 0.3 0.03 0.3 0.03 0.5 0.05 0.5 0.05 8 mm Note: Values in shaded cells indicate thickness class (unit: mm) 95 MLCC Selection Charts X7R - General purpose & High capacitance, 0603 / 0805 X7R General purpose & High capacitance Capacitance Last 2-digit of 12NC 100 pF 150 pF 220 pF 330 pF 470 pF 680 pF 1000 pF 1.5 nF 2.2 nF 3.3 nF 4.7 nF 6.8 nF 10 nF 15 nF 22 nF 33 nF 47 nF 68 nF 100 nF 150 nF 220 nF 330 nF 470 nF 680 nF 1000 nF 2.2 uF 4.7 uF 10 uF Tape width 09 12 14 16 18 21 23 25 27 29 32 34 36 38 41 43 45 47 49 52 54 56 58 61 63 67 72 76 0603 6.3V 10V 16V 25V 50V 0.8 0.1 0.8 0.1 0.8 0.1 0.8 0.1 6.3V 10V 16V 25V 50V 0.6 0.1 0.6 0.1 0.85 0.1 0.6 0.1 0.8 0.1 Note: Values in shaded cells indicate thickness class (unit: mm) 96 0805 0.85 0.1 0.85 0.1 1.25 0.2 1.25 0.2 0.85 0.1 0.85 0.1 1.25 0.2 1.25 0.2 1.25 0.2 1.25 0.2 8 mm MLCC Selection Charts X7R - Gerneral purpose & High capacitance, 1206 to 1812 X7R General purpose & High capacitance Capacitance Last 2-digit of 12NC 470 pF 680 pF 1000 pF 1.5 nF 2.2 nF 3.3 nF 4.7 nF 6.8 nF 10 nF 15 nF 22 nF 33 nF 47 nF 68 nF 100 nF 150 nF 220 nF 330 nF 470 nF 680 nF 1000 nF 2.2 uF 4.7 uF 10 uF 22 uF Tape width 18 21 23 25 27 29 32 34 36 38 41 43 45 47 49 52 54 56 58 61 63 67 72 76 81 1206 6.3V 10V 16V 1210 25V 50V 10V 16V 1812 25V 50V 50V 0.85 0.1 0.85 0.1 0.85 0.1 1.15 0.1 0.85 0.1 1.15 0.1 1.15 0.1 0.85 0.1 0.85 0.1 1.15 0.1 1.15 0.1 1.15 0.1 1.15 0.1 1.6 0.2 1.6 0.2 0.85 0.1 0.85 0.1 1.0 0.1 1.15 0.1 1.15 0.1 1.15 0.1 1.6 0.2 1.25 0.2 1.6 0.2 1.25 0.2 1.6 0.2 1.25 0.2 1.9 0.2 1.6 0.2 1.6 0.2 1.9 0.2 1.9 0.2 2.5 0.2 8 mm 12mm Note: Values in shaded cells indicate thickness class (unit: mm) 97 MLCC Selection Charts X7R - Midium voltage, 0603 / 0805 X7R Medium voltage Capacitance Last 2-digit of 12NC 100 pF 150 pF 220 pF 330 pF 470 pF 680 pF 1000 pF 1.5 nF 2.2 nF 2.7 nF 3.3 nF 4.7 nF 5.6 nF 6.8 nF 10 nF 15 nF 22 nF 33 nF 47 nF Tape width 09 12 14 16 18 21 23 25 27 28 29 32 33 34 36 38 41 43 45 0603 100V 100V 200V 250V 0.6 0.1 0.85 0.1 0.85 0.1 1.25 0.2 1.25 0.2 0.8 0.1 0.8 0.1 1.25 0.2 1.25 0.2 500V 0.8 0.1 Note: Values in shaded cells indicate thickness class (unit: mm) 98 0805 0.8 0.1 1.25 0.2 0.85 0.1 1.25 0.2 8 mm MLCC Selection Charts X7R - Midium voltage, 1206 / 1210 X7R Medium voltage Capacitance Last 2-digit of 12NC 220 pF 330 pF 470 pF 680 pF 820 pF 1000 pF 1.2 nF 1.5 nF 1.8 nF 2.2 nF 2.7 nF 3.3 nF 3.9 nF 4.7 nF 6.8 nF 10 nF 12 nF 15 nF 18 nF 22 nF 33 nF 47 nF 56 nF 68 nF 82 nF 100 nF 120 nF 150 nF 180 nF 220 nF Tape width 14 16 18 21 22 23 24 25 26 27 28 29 31 32 34 36 37 38 39 41 43 45 46 47 48 49 51 52 53 54 1206 100V 200V 250V 1210 500V 630V 100V 200V 250V 500V 630V 0.85 0.1 1.15 0.15 1.15 0.15 1.15 0.15 1.15 0.15 0.85 0.1 0.85 0.1 1.25 0.2 0.85 0.1 0.85 0.1 0.85 0.1 1.15 0.15 1.25 0.2 1.25 0.2 1.25 0.2 1.15 0.15 1.15 0.15 1.15 0.15 1.15 0.15 1.6 0.2 1.25 0.2 1.6 0.2 2.0 0.2 1.25 0.2 1.15 0.15 1.25 0.2 1.25 0.2 1.15 0.1 1.6 0.2 1.25 0.2 8 mm Note: Values in shaded cells indicate thickness class (unit: mm) 99 MLCC Selection Charts X7R - Midium voltage, 1808 / 1812 X7R Medium voltage Capacitance Last 2-digit of 12NC 1000 pF 1.5 nF 2.2 nF 3.3 nF 4.7 nF 6.8 nF 10 nF 15 nF 22 nF 33 nF 47 nF 68 nF 100 nF 150 nF 220 nF 330 nF 470 nF Tape width 23 26 28 29 32 34 36 38 41 43 45 47 49 52 54 56 58 1808 100V 200V 500V 630V 100V 200V 250V 500V 1.35 0.15 1.25 0.2 1.25 0.2 Note: Values in shaded cells indicate thickness class (unit: mm) 100 250V 1812 1.25 0.2 630V 1.35 0.15 1.25 0.2 0.85 0.1 1.25 0.2 0.85 0.1 0.85 0.1 0.85 0.1 1.6 0.2 1.15 0.1 1.15 0.15 1.25 0.2 1.25 0.2 1.6 0.2 1.15 0.15 1.15 0.15 1.15 0.1 2.0 0.2 12 mm 1.6 0.2 1.6 0.2 1.6 0.2 2.0 0.2 2.0 0.2 MLCC Selection Charts X7R - High voltage, 1206 / 1210 X7R High voltage Capacitance Last 2-digit of 12NC 220 pF 330 pF 470 pF 680 pF 1000 pF 1.5 nF 2.2 nF 3.3 nF 4.7 nF 6.8 nF 10 nF 15 nF 22 nF 33 nF Tape width 14 16 18 21 23 25 27 29 32 34 36 38 41 43 1206 1210 1kV 2kV 1.15 0.15 1.25 0.2 1kV 2kV 1.25 0.2 1.25 0.2 1.6 0.2 1.25 0.2 1.6 0.2 2.0 0.2 8 mm Note: Values in shaded cells indicate thickness class (unit: mm) 101 MLCC Selection Charts X7R - High voltage, 1808 / 1812 X7R High voltage Capacitance Last 2-digit of 12NC 150 pF 220 pF 330 pF 470 pF 680 pF 1000 pF 1.5 nF 2.2 nF 3.3 nF 4.7 nF 6.8 nF 10 nF 15 nF 22 nF 33 nF Tape width 12 14 16 18 21 23 25 27 29 32 34 36 38 41 43 1808 1kV 3kV 1kV 2kV 3kV 1.6 0.2 1.25 0.2 1.35 0.15 1.35 0.15 2.0 0.2 1.35 0.15 1.35 0.15 1.6 0.2 2.0 0.2 1.25 0.2 1.6 0.2 Note: Values in shaded cells indicate thickness class (unit: mm) 102 2kV 1812 1.6 0.2 2.0 0.2 1.25 0.2 1.6 0.2 12 mm MLCC Selection Charts X7R - General purpose, High Capacitance, Midium & High voltage Global part number - Preferred type Global Part Number is the preferred clear text code for ordering Yageo and Phycomp branded products. For details, please see page 76. 12NC ordering code - Phycomp branded product only 22 XX XX X X X X Carrier tape 38 = Paper (10 V ) 22 = Blister (10 V ) 50 = Blister (6.3 V / 1 kV) 55 = Paper (6.3 V / 1 kV) 54 = Bulk Voltage 20 = 6.3 V 24 = 10 V 78 = 16 V 91 = 25 V 58 = 50 V 60 = 100 V 93 = 200 V 83 = 250 V 97 = 500 V 98 = 630 V 00 = 1 kV 02 = 2 kV 99 = 2.5 kV 04 = 3 kV 50 = 4 kV XX Capacitance value See selection chart Tolerance 5 = 5% 6 = 10% 7 = 20% TC material 5 = X7R Packing 1 = 180 mm / 7" reel 5 = 330 mm / 13" reel 4 = Bulk case Size 8 = 0201 7 = 0402 6 = 0603 0 = 0805 1 = 1206 2 = 1210 3 = 1808 4 = 1812 Phycomp CTC ordering code - North America Regional code for ordering Phycomp branded products. For details, please see page 77. 103 MLCC Selection Charts X7R - Low inductance, 0306 to 0612 X7R Low inductance Capacitance Last 2-digit of 12NC 10 nF 22 nF 47 nF 100 nF 220 nF Tape width 36 41 45 49 54 10V 16V 0306 0508 0.5 0.1 Note: Values in shaded cells indicate thickness class (unit: mm) 104 25V 0.85 0.1 8 mm 50V 0508 0612 0.85 0.1 0.85 0.1 MLCC Selection Charts X7R - Low inductance, 0306 to 0612 Global part number - Preferred type Global Part Number is the preferred clear text code for ordering Yageo and Phycomp branded products. For details, please see page 76. 12NC ordering code - Phycomp branded product only 22 XX XX X X 5 X XX Carrier tape 55 = Paper Capacitance value See selection chart Voltage 09 = 10 V 08 = 16 V 07 = 25 V 06 = 50V Tolerance 6 = 10% Packing 1 = 180 mm / 7" reel 5 = 330 mm / 13" reel Size 1 = 0508 2 = 0306 0 = 0612 Phycomp CTC ordering code - North America Regional code for ordering Phycomp branded products. For details, please see page 77. 105 MLCC Selection Charts X5R - General purpose & High capacitance, 0201 / 0402 X5R General purpose & High capacitance Capacitance Last 2-digit of 12NC 10 nF 100 nF 150 nF 220 nF 470 nF 1000 nF Tape width 36 49 52 54 58 63 0201 6.3V 10V 16V 0.3 0.03 0.3 0.03 0.3 0.03 Note: Values in shaded cells indicate thickness class (unit: mm) 106 0402 8 mm 6.3V 10V 16V 0.5 0.05 0.5 0.05 0.5 0.05 MLCC Selection Charts X5R - General purpose & High capacitance, 0603 / 0805 X5R General purpose & High capacitance Capacitance Last 2-digit of 12NC 330 nF 470 nF 1000 nF 2.2 uF 4.7 uF 10 uF 22 uF Tape width 56 58 63 67 72 76 81 0603 6.3V 0.8 0.1 10V 0805 16V 25V 0.8 0.1 0.8 0.1 6.3V 10V 16V 25V 1.25 0.2 1.25 0.2 1.25 0.2 1.25 0.2 0.85 0.1 0.85 0.1 0.85 0.1 1.25 0.2 1.25 0.2 1.25 0.2 0.8 0.1 8 mm Note: Values in shaded cells indicate thickness class (unit: mm) 107 MLCC Selection Charts X5R - High capacitance, 1206 to 1812 X5R High capacitance Capacitance Last 2-digit of 12NC 2.2 uF 4.7 uF 10 uF 22 uF 47 uF 100 uF Tape width 67 72 76 81 85 89 1206 6.3V 10V 16V 25V 1.15 0.1 1.15 0.1 1.15 0.1 1.6 0.2 1.6 0.2 1.15 0.1 1.6 0.2 6.3V 10V 1.6 0.2 Note: Values in shaded cells indicate thickness class (unit: mm) 108 1210 1812 16V 25V 1.9 0.2 1.9 0.2 6.3V 10V 2.5 0.2 2.5 0.2 1.9 0.2 2.0 0.2 2.0 0.2 2.5 0.2 2.5 0.2 3.2 0.3 8 mm 12 mm MLCC Selection Charts X5R - General purpose & High Capacitance, 0201 to 1812 Global part number - Preferred type Global Part Number is the preferred clear text code for ordering Yageo and Phycomp branded products. For details, please see page 76. 12NC ordering code - Phycomp branded product only 22 XX XX X X X X Carrier tape 50 = Blister (6.3 V) 55 = Paper (6.3 V) 38 = Paper (10 V) 22 = Blister (10 V) 54 = Bulk Voltage 20 = 6.3 V 24 = 10 V 78 = 16 V 91 = 25 V 58 = 50 V Size 8 = 0201 7 = 0402 6 = 0603 0 = 0805 1 = 1206 2 = 1210 4 = 1812 XX Capacitance value See selection chart Tolerance 5 = 5% 6 = 10% 7 = 20% TC material 3 = X5R Packing 1 = 180 mm / 7" reel 5 = 330 mm / 13" reel 4 = Bulk case Phycomp CTC ordering code - North America Regional code for ordering Phycomp branded products. For details, please see page 77. 109 MLCC Selection Charts Y5V - General purpose & High capacitance, 0201 / 0402 Y5V General purpose & High capacitance Capacitance Last 2-digit of 12NC 10 nF 22 nF 47 nF 100 nF 220 nF 470 nF 1000 nF Tape width 36 41 45 49 54 58 63 0201 6.3V 25V 6.3V 10V 0.3 0.03 0.3 0.03 Note: Values in shaded cells indicate thickness class (unit: mm) 110 0402 0.5 0.05 0.5 0.05 8 mm 16V 25V 0.5 0.05 0.5 0.05 MLCC Selection Charts Y5V - General purpose & High capacitance, 0603 / 0805 Y5V General purpose & High capacitance Capacitance Last 2-digit of 12NC 10 nF 22 nF 47 nF 100 nF 220 nF 470 nF 1000 nF 2.2 uF 4.7 uF 10 uF 22 uF Tape width 36 41 45 49 54 58 63 67 72 76 81 0603 6.3V 10V 16V 0805 25V 50V 0.8 0.1 0.8 0.1 6.3V 10V 16V 25V 50V 0.6 0.1 0.6 0.1 0.6 0.1 0.85 0.1 0.85 0.1 0.85 0.1 0.8 0.1 0.85 0.1 0.8 0.1 1.25 0.2 0.8 0.1 1.25 0.2 1.25 0.2 1.25 0.2 1.25 0.2 8 mm Note: Values in shaded cells indicate thickness class (unit: mm) 111 MLCC Selection Charts Y5V - General purpose & High capacitance, 1206 / 1210 Y5V General purpose & High capacitance Capacitance Last 2-digit of 12NC 10 nF 22 nF 47 nF 100 nF 220 nF 470 nF 1000 nF 2.2 uF 4.7 uF 10 uF 22 uF 47 uF Tape width 36 41 45 49 54 58 63 67 72 76 81 85 1206 6.3V 10V 16V 25V 50V 0.6 0.1 0.6 0.1 0.6 0.1 0.85 0.1 0.85 0.1 0.85 0.1 6.3V 10V 16V 25V 1.5 0.1 1.5 0.1 1.5 0.1 0.6 0.1 0.85 0.1 1.15 0.1 1.15 0.1 1.15 0.1 1.6 0.2 1.6 0.2 Note: Values in shaded cells indicate thickness class (unit: mm) 112 1210 1.6 0.2 1.6 0.2 2.0 0.2 8 mm MLCC Selection Charts Y5V - General purpose & High Capacitance, 0201 to 1210 Global part number - Preferred type Global Part Number is the preferred clear text code for ordering Yageo and Phycomp branded products. For details, please see page 76. 12NC ordering code - Phycomp branded product only 22 XX XX X X 9 X XX Carrier tape 50 = Blister (6.3 V) 55 = Paper (6.3 V) 38 = Paper 22 = Blister 54 = Bulk Capacitance value See selection chart Voltage 20 = 6.3 V 24 = 10 V 78 = 16 V 91 = 25 V 58 = 50 V Packing 1 = 180 mm / 7" reel 5 = 330 mm / 13" reel 4 = Bulk case Tolerance 7 = 20% 8 = -20 to +80% Size 8 = 0201 7 = 0402 6 = 0603 0 = 0805 1 = 1206 2 = 1210 Phycomp CTC ordering code - North America Regional code for ordering Phycomp branded products. For details, please see page 77. 113 MLCC Selection Charts NP0 - High voltage SC type, 1808 / 1812 NP0 Capacitance Last 2-digit of 12NC 10 pF 12 pF 15 pF 18 pF 22 pF 27 pF 33 pF 39 pF 47 pF 56 pF 68 pF 82 pF 100 pF 120 pF 150 pF 180 pF 220 pF 270 pF 330 pF 390 pF 470 pF 560 pF 680 pF 820 pF 1000 pF Tape Width 23 24 25 26 27 28 29 31 32 33 34 35 36 37 38 39 41 42 43 44 45 46 47 48 49 1808 1808 X1/Y2 for UL X1/Y2 for TUV X1/Y2 for UL X2/Y3 for TUV X2/Y3 for UL 1.6 0.2 1.6 0.2 1.6 0.2 1.6 0.2 1.6 0.2 1.6 0.2 2.0 0.2 2.0 0.2 2.0 0.2 2.0 0.2 2.0 0.2 2.0 0.2 Note: Values in shaded cells indicate thickness class (unit: mm) 114 1812 X1/Y2 for TUV 12 mm MLCC Selection Charts X7R - High voltage SC type, 1808 / 1812 X7R Capacitance Last 2-digit of 12NC 150 pF 180 pF 220 pF 270 pF 330 pF 390 pF 470 pF 560 pF 680 pF 820 pF 1000 pF 1.2 nF 1.5 nF Tape width 12 13 14 15 16 17 18 19 21 22 23 24 25 1808 1812 X1/Y2 for TUV X1/Y2 for UL 1.6 0.2 1.6 0.2 2.0 0.2 2.0 0.2 X1/Y2 for TUV 1808 X1/Y2 for UL 1.6 0.2 1.6 0.2 2.0 0.2 2.0 0.2 X2/Y3 for TUV X2/Y3 for UL 1.6 0.2 1.6 0.2 2.0 0.2 2.0 0.2 12 mm Note: Values in shaded cells indicate thickness class (unit: mm) 115 MLCC Selection Charts NP0 / X7R - High voltage SC type, 1808 / 1812 Global part number - Preferred type Global Part Number is the preferred clear text code for ordering Yageo and Phycomp branded products. For details, please see page 76. 12NC ordering code - Phycomp branded product only 22 XX XX X X X X XX Carrier tape 50 = Blister Capacitance value See selection chart Voltage 52 = X2/Y3 53 = X1/Y2 Tolerance 5 = 5% 6 = 10% Size 3 = 1808 4 = 1812 TC material 1 = NP0 5 = X7R Packing 1 = 180 mm / 7" reel 5 = 330 mm / 13" reel Phycomp CTC ordering code - North America Regional code for ordering Phycomp branded products. For details, please see page 77. 116 MLCC Selection Charts X7R - 2C Arrays, 0405 X7R 2-C arrays Capacitance Last 2-digit of 12NC 0405 10 nF 12 nF 15 nF 18 nF 22 nF 27 nF 33 nF 39 nF 47 nF 56 nF 68 nF 82 nF 100 nF Tape width 36 37 38 39 41 42 43 44 45 46 47 48 49 0.6 0.1 16V 8 mm Note: Values in shaded cells indicate thickness class (unit: mm) 117 MLCC Selection Charts X7R - 2C Arrays, 0405 Global part number - Preferred type Global Part Number is the preferred clear text code for ordering Yageo and Phycomp branded products. For details, please see page 76. 12NC ordering code - Phycomp branded product only 22 XX XX 2 X X X Carrier tape 50 = Blister 55 = Paper Capacitance value See selection chart Voltage 70 = 16 V Tolerance 6 = 10% 7 = 20% Packing 1 = 180 mm / 7" reel TC material 5 = X7R Phycomp CTC ordering code - North America Regional code for ordering Phycomp branded products. For details, please see page 77. 118 XX MLCC Selection Charts NP0 - 4C Arrays, 0508 / 0612 NP0 4-C arrays Capacitance Last 2-digit of 12NC 0508 0612 50V 50V 10 pF 15 pF 18 pF 22 pF 27 pF 47 pF 100 pF 150 pF 180 pF 220 pF 270 pF 330 pF 390 pF 470 pF 560 pF 680 pF 820 pF 1000 pF Tape width 23 25 26 27 28 32 36 38 39 41 42 43 44 45 46 47 48 49 0.6 0.1 0.8 0.1 8 mm Note: Values in shaded cells indicate thickness class (unit: mm) 119 MLCC Selection Charts X7R - 4C Arrays, 0508 / 0612 X7R 4-C arrays Capacitance Last 2-digit of 12NC 220 pF 470 pF 1000 pF 2.2 nF 4.7 nF 10 nF 22 nF 47 nF 100 nF Tape width 16 21 23 29 32 36 41 45 49 0508 16V 0.8 0.1 Note: Values in shaded cells indicate thickness class (unit: mm) 120 0612 16V 0.8 0.1 8 mm 25V 50V 0.8 0.1 0.8 0.1 MLCC Selection Charts Y5V - 4C Arrays, 0508 / 0612 Y5V 4-C arrays Capacitance Last 2-digit of 12NC 0508 0612 25V 25V 10 nF 22 nF 47 nF 100 nF Tape width 36 41 45 49 0.6 0.1 0.6 0.1 8 mm Note: Values in shaded cells indicate thickness class (unit: mm) 121 MLCC Selection Charts NP0 / X7R / Y5V - 4C Arrays, 0508 / 0612 Global part number - Preferred type Global Part Number is the preferred clear text code for ordering Yageo and Phycomp branded products. For details, please see page 76. 12NC ordering code - Phycomp branded product only 22 XX XX X X X X Carrier tape 50 = Blister 55 = Paper Voltage 10 = 16 V 12 = 25 V 14 = 50 V Size 6 = 0612 (4 x 0603) 7 = 0508 (4 x 0402) Packing 1 = 180 mm / 7" reel Phycomp CTC ordering code - North America Regional code for ordering Phycomp branded products. For details, please see page 77. 122 XX Capacitance value See selection chart Tolerance 5 = 5% 6 = 10% 7 = 20% 8 = -20 to +80% TC material 1 = NP0 5 = X7R 9 = Y5V MLCC Engineering Design Kits Sample kits for 0201 / 0402 0201 sample kits NP0 50 V Capacitance (pF) 1 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 Tolerance 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.50 pF 0.50 pF 0.50 pF 5% 5% 5% 5% 5% NP0 25 V Capacitance (pF) Tolerance 27 5% 33 5% 39 5% 47 5% 56 5% 68 5% 82 5% 100 5% Y5V 6.3V Capacitance (pF) Tolerance 100 000 -20% to +80% X5R 6.3V Capacitance (pF) Tolerance 100 000 10% X7R 50 V Capacitance (pF) 47 68 100 150 220 330 470 X7R 25 V Capacitance (pF) 680 1 000 X7R 16V Capacitance (pF) 1 500 2 200 3 300 X7R 10 V Capacitance (pF) 10 000 Tolerance 10% 10% 10% 10% 10% 10% 10% Tolerance 10% 10% Tolerance 10% 10% 10% Tolerance 10% Note: 100 pieces per value. Ordering code 432204407111 for Phycomp brand product, CC020100000000000 for Yageo brand product 0402 sample kits NP0 50 V Capacitance (pF) 0.47 0.68 1 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 Tolerance 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.50 pF 5% 5% 5% 5% 5% 5% 5% 5% 5% Y5V 16 V Capacitance (pF) 10 000 22 000 47 000 100 000 Tolerance 20% 20% 20% 20% X7R 50 V Capacitance (pF) 100 150 220 330 470 680 1 000 1 500 2 200 3 300 X7R 25 V Capacitance (pF) 4 700 X7R 16 V Capacitance (pF) 6 800 10 000 15 000 22 000 Tolerance 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% Tolerance 10% Tolerance 10% 10% 10% 10% Note: 95 pieces per value. Ordering code 432204409911 for Phycomp brand product, CC040200000000000 for Yageo brand product 123 MLCC Engineering Design Kits Sample kits for 0603 / 0805 0603 sample kits NP0 50 V Capacitance (pF) 0.47 0.68 1 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 Tolerance 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.50 pF 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% NP0 25 V Capacitance (pF) 1 000 1 500 Y5V 50 V Capacitance (pF) 10 000 22 000 47 000 100 000 Y5V 16 V Capacitance (pF) 220 000 470 000 Tolerance 5% 5% Tolerance 20% 20% 20% 20% Tolerance 20% 20% X7R 50 V Capacitance (pF) 100 150 220 330 470 680 1 000 1 500 2 200 3 300 4 700 6 800 10 000 X7R 25 V Capacitance (pF) 15 000 22 000 X7R 16 V Capacitance (pF) 33 000 47 000 68 000 100 000 Tolerance 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% Tolerance 10% 10% Tolerance 10% 10% 10% 10% Note: 48 pieces per value. Ordering code 432204407121 for Phycomp brand product, CC060300000000000 for Yageo brand product 0805 sample kits NP0 50 V Capacitance (pF) 0.47 0.68 1 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 1 000 1 500 2 200 124 Tolerance 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.50 pF 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% NP0 25 V Capacitance (pF) 3 300 4 700 Y5V 50 V Capacitance (pF) 10 000 22 000 47 000 100 000 220 000 Y5V 16 V Capacitance (pF) 470 000 1 000 000 Tolerance 5% 5% Tolerance 20% 20% 20% 20% 20% Tolerance 20% 20% X7R 50 V Capacitance (pF) 220 330 470 680 1 000 1 500 2 200 3 300 4 700 6 800 10 000 15 000 22 000 33 000 47 000 68 000 100 000 X7R 16 V Capacitance (pF) 150 000 220 000 330 000 470 000 Note: 48 pieces per value. Ordering code 432204407131 for Phycomp brand product, CC080500000000000 for Yageo brand product Tolerance 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% Tolerance 10% 10% 10% 10% MLCC Engineering Design Kits Sample kits for 1206 1206 sample kits NP0 50 V Capacitance (pF) 0.47 0.68 1 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 1 000 1 500 2 200 3 300 4 700 6 800 Tolerance 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.50 pF 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% NP0 25 V Capacitance (pF) 10 000 Y5V 50 V Capacitance (pF) 100 000 220 000 470 000 1 000 000 Tolerance 5% Tolerance 20% 20% 20% 20% X7R 50 V Capacitance (pF) 220 330 470 680 1 000 1 500 2 200 3 300 4 700 6 800 10 000 15 000 22 000 33 000 47 000 68 000 100 000 150 000 220 000 X7R 16 V Capacitance (pF) 330 000 470 000 680 000 1 000 000 Tolerance 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% Tolerance 10% 10% 10% 10% Note: 48 pieces per value. Ordering code 432204407141 for Phycomp brand product, CC120600000000000 for Yageo brand product 125 MLCC Engineering Design Kits Sample kits for high capacitance series High capacitance sample kits Capacitance 1 F 1 F 2.2 F Capacitance 1 F 1 F 2.2 F 2.2 F 2.2 F 4.7 F 4.7 F 10 F Capacitance 2.2 F 4.7 F 4.7 F 4.7 F 10 F 10 F 10 F 22 F Capacitance 4.7 F 4.7 F 10 F 10 F 22 F X5R 0402 Rated voltage 6.3 V 10 V 6.3 V X5R 0603 Rated voltage 16 V 25 V 6.3 V 10 V 16 V 6.3 V 10 V 6.3 V X5R 0805 Rated voltage 25 V 6.3 V 10 V 16 V 6.3 V 10 V 16 V 6.3 V X5R 1206 Rated voltage 16 V 25 V 16 V 25 V 6.3 V Tolerance 10% 10% 20% Tolerance 10% 10% 10% 10% 10% 10% 10% 20% Tolerance 10% 10% 10% 10% 10% 10% 10% 20% Capacitance 1 F Capacitance 1 F 2.2 F 2.2 F Capacitance 1 F 2.2 F 4.7 F 10 F 10 F X7R 0603 Rated voltage 16 V X7R 0805 Rated voltage 25 V 16 V 25 V X7R 1206 Rated voltage 25 V 25 V 25 V 16 V 25 V Tolerance 10% Tolerance 10% 10% 10% Tolerance 10% 10% 10% 10% 10% Capacitance 1 F 1 F Capacitance 1 F 1 F 2.2 F 2.2 F 4.7 F Capacitance 1 F 1 F 1 F 2.2 F 4.7 F 10 F Capacitance 4.7 F 10 F 10 F 22 F Tolerance 10% 10% 10% 10% 20% Note: 50 pieces per value. Ordering code 432204510001 for Phycomp brand product, CC888800000000000 for Yageo brand product 126 Y5V 0402 Rated voltage 6.3 V 10 V Y5V 0603 Rated voltage 10 V 16 V 10 V 16 V 6.3 V Y5V 0805 Rated voltage 16 V 25 V 50 V 16 V 10 V 10 V Y5V 1206 Rated voltage 16 V 10 V 16 V 16 V Tolerance -20% to +80% -20% to +80% Tolerance -20% to +80% -20% to +80% -20% to +80% -20% to +80% -20% to +80% Tolerance -20% to +80% -20% to +80% -20% to +80% -20% to +80% -20% to +80% -20% to +80% Tolerance -20% to +80% -20% to +80% -20% to +80% -20% to +80% MLCC Engineering Design Kits High voltage sample kits for PCs segment High voltage sample kits for PCs segment Capacitance 10 pF 15 pF 22 pF 33 pF 47 pF 68 pF 100 pF 150 pF 220 pF 330 pF 470 pF Capacitance 470 pF 680 pF 1 nF 1.5 nF 470 pF 680 pF 1 nF 1.5 nF 2.2 nF 3.3 nF NP0 1808 Rated voltage 3 kV 3 kV 3 kV 3 kV 3 kV 3 kV 3 kV 3 kV 3 kV 3 kV 3 kV X7R 1808 Rated voltage 3 kV 3 kV 3 kV 3 kV 2 kV 2 kV 2 kV 2 kV 2 kV 2 kV Tolerance 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% Capacitance 10 pF 15 pF 22 pF 33 pF 47 pF 68 pF 100 pF 150 pF 220 pF 330 pF 470 pF Tolerance 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% Capacitance 1 nF 1.5 nF NP0 1812 Rated voltage 3 kV 3 kV 3 kV 3 kV 3 kV 3 kV 3 kV 3 kV 3 kV 3 kV 3 kV X7R 1206 Rated voltage 2 kV 2 kV Tolerance 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% Tolerance 10% 10% Note: 50 pieces per value. Ordering code 432204510011 for Phycomp brand product, HV999900000000000 for Yageo brand product 127 MLCC Engineering Design Kits High voltage sample kits for inverter segment High voltage sample kits for inverter segment Capacitance 5 pF 10 pF 12 pF 15 pF 18 pF 22 pF 27 pF 33 pF 39 pF 47 pF 56 pF 68 pF 82 pF 100 pF 120 pF 150 pF 220 pF 330 pF 470 pF NP0 1808 Rated voltage 3 kV 3 kV 3 kV 3 kV 3 kV 3 kV 3 kV 3 kV 3 kV 3 kV 3 kV 3 kV 3 kV 3 kV 3 kV 3 kV 3 kV 3 kV 3 kV Note: 50 pieces per value. Ordering code 432204510012 for Phycomp brand product, HV888800000000000 for Yageo brand product 128 Tolerance 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% MLCC Engineering Design Kits High voltage sample kits for general application High voltage sample kits for general application Capacitance 10 pF 100 pF 1 nF 10 pF 100 pF Capacitance 10 pF 100 pF 1 nF 10 pF 100 pF Capacitance 10 pF 100 pF 1 nF 10 pF 100 pF 10 pF 10 pF 100 pF Capacitance 10 pF 100 pF 1 nF 10 pF 100 pF 1 nF 10 pF 100 pF 10 nF NP0 1206 Rated voltage 1 kV 1 kV 1 kV 2 kV 2 kV NP0 1210 Rated voltage 1 kV 1 kV 1 kV 2 kV 2 kV NP0 1808 Rated voltage 1 kV 1 kV 1 kV 3 kV 3 kV 4 kV 2 kV 2 kV NP0 1812 Rated voltage 2 kV 2 kV 2 kV 1 kV 1 kV 1 kV 3 kV 3 kV 4 kV Tolerance 5% 5% 5% 5% 5% Tolerance 5% 5% 5% 5% 5% Tolerance 5% 5% 5% 5% 5% 5% 5% 5% Capacitance 10 nF 1 nF 1 nF Capacitance 1 nF 10 nF 1 nF Capacitance 10 nF 1 nF 1 nF 1 nF Capacitance 10 nF 1 nF 10 nF X7R 1206 Rated voltage 1 kV 2 kV 1 kV X7R 1210 Rated voltage 1 kV 1 kV 2 kV X7R 1808 Rated voltage 1 kV 3 kV 1 kV 2 kV X7R 1812 Rated voltage 2 kV 1 kV 1 kV Tolerance 10% 10% 10% Tolerance 10% 10% 10% Tolerance 10% 10% 10% 10% Tolerance 10% 10% 10% Tolerance 5% 5% 5% 5% 5% 5% 5% 5% 5% Note: 50 pieces per value. Ordering code 432204510013 for Phycomp brand product, HV777700000000000 for Yageo brand product 129 MLCC Engineering Design Kits High voltage sample kits for safety certification MLCCs High voltage sample kits for safety certification MLCCs Capacitance 10 pF 22 pF 47 pF 100 pF 150 pF 220 pF 330 pF Capacitance 10 pF 22 pF 47 pF 100 pF 150 pF 220 pF 330 pF Capacitance 10 pF 22 pF 47 pF 100 pF 150 pF 220 pF 330 pF 470 pF Capacitance 22 pF 47 pF 100 pF 150 pF 220 pF Capacitance 10 pF 22 pF 47 pF 100 pF 150 pF 220 pF Capacitance 150 pF 330 pF 680 pF 1.5 nF NP0 1808 TUV Safety cretification X1 / Y2 X1 / Y2 X1 / Y2 X1 / Y2 X1 / Y2 X1 / Y2 X1 / Y2 NP0 1808 UL Safety cretification X1 / Y2 X1 / Y2 X1 / Y2 X1 / Y2 X1 / Y2 X1 / Y2 X1 / Y2 NP0 1812 TUV Safety cretification X1 / Y2 X1 / Y2 X1 / Y2 X1 / Y2 X1 / Y2 X1 / Y2 X1 / Y2 X1 / Y2 NP0 1812 UL Safety cretification X1 / Y2 X1 / Y2 X1 / Y2 X1 / Y2 X1 / Y2 NP0 1808 TUV Safety cretification X2 / Y3 X2 / Y3 X2 / Y3 X2 / Y3 X2 / Y3 X2 / Y3 NP0 1808 UL Safety cretification X2 / Y3 X2 / Y3 X2 / Y3 X2 / Y3 Tolerance 5% 5% 5% 5% 5% 5% 5% Tolerance 5% 5% 5% 5% 5% 5% 5% Tolerance 5% 5% 5% 5% 5% 5% 5% 5% Tolerance 5% 5% 5% 5% 5% Tolerance 5% 5% 5% 5% 5% 5% Capacitance 150 pF 220 pF 330 pF 470 pF 680 pF 1 nF Capacitance 150 pF 220 pF 330 pF 470 pF 680 pF 1 nF Capacitance 220 pF 330 pF 470 pF 680 pF 1 nF 1.5 nF Capacitance 220 pF 330 pF 470 pF 680 pF 1 nF 1.5 nF Capacitance 470 pF 680 pF 1 nF 1.5 nF Capacitance 220 pF 470 pF 1 nF 1.5 nF X7R 1808 TUV Safety cretification X1 / Y2 X1 / Y2 X1 / Y2 X1 / Y2 X1 / Y2 X1 / Y2 X7R 1808 UL Safety cretification X1 / Y2 X1 / Y2 X1 / Y2 X1 / Y2 X1 / Y2 X1 / Y2 X7R 1812 TUV Safety cretification X1 / Y2 X1 / Y2 X1 / Y2 X1 / Y2 X1 / Y2 X1 / Y2 X7R 1812 UL Safety cretification X1 / Y2 X1 / Y2 X1 / Y2 X1 / Y2 X1 / Y2 X1 / Y2 X7R 1808 TUV Safety cretification X2 / Y3 X2 / Y3 X2 / Y3 X2 / Y3 X7R 1808 UL Safety cretification X2 / Y3 X2 / Y3 X2 / Y3 X2 / Y3 Tolerance 5% 5% 5% 5% Note: 50 pieces per value. Ordering code 432204510014 for Phycomp brand product, SC999900000000000 for Yageo brand product 130 Tolerance 10% 10% 10% 10% 10% 10% Tolerance 10% 10% 10% 10% 10% 10% Tolerance 10% 10% 10% 10% 10% 10% Tolerance 10% 10% 10% 10% 10% 10% Tolerance 10% 10% 10% 10% Tolerance 10% 10% 10% 10% MLCC Engineering Design Kits Sample kits for high frequency series 0402 high frequency sample kits Capacitance 0.22 pF 0.3 pF 0.4 pF 0.5 pF 0.6 pF 0.7 pF 0.8 pF 0.9 pF 1 pF 1.2 pF 1.5 pF 1.8 pF 2.2 pF 2.7 pF 3.3 pF 3.9 pF 4.7 pF 5.6 pF 6.8 pF 8.2 pF 10 pF NP0 Rated voltage 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V Tolerance 0.1 pF 0.1 pF 0.1 pF 0.1 pF 0.1 pF 0.1 pF 0.1 pF 0.1 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.5 pF 0.5 pF 0.5 pF 0.5 pF Note: 50 pieces per value. Ordering code 432204409912 for Phycomp brand product, CH040200000000000 for Yageo brand product 0603 high frequency sample kits Capacitance 0.22 pF 0.3 pF 0.47 pF 0.5 pF 0.6 pF 0.7 pF 0.8 pF 0.9 pF 1 pF 1.2 pF 1.5 pF 1.8 pF 2.2 pF 2.7 pF 3.3 pF 3.9 pF 4.7 pF 5.6 pF 6.8 pF 8.2 pF 10 pF NP0 Rated voltage 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V 50 V Tolerance 0.1 pF 0.1 pF 0.1 pF 0.1 pF 0.1 pF 0.1 pF 0.1 pF 0.1 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.25 pF 0.5 pF 0.5 pF 0.5 pF 0.5 pF Note: 50 pieces per value. Ordering code 432204407122 for Phycomp brand product, CH060300000000000 for Yageo brand product 131 MLCC Engineering Design Kits Sample kits for all sizes, all types, E1 series only All sizes, all types, E1 series only General purpose & High capacitance NP0 50 V Capacitance (pF) Tolerance 0402 1 0.25 pF 10 5% 100 5% NP0 50 V Capacitance (pF) Tolerance 0603 1 0.25 pF 10 5% 100 5% NP0 50 V Capacitance (pF) Tolerance 1 0.25 pF 0805 10 5% 100 5% 1 000 5% NP0 50 V Capacitance (pF) Tolerance 1 0.25 pF 1206 10 5% 100 5% 1 000 5% X7R 50 V Capacitance (pF) Tolerance 100 10% 1 000 10% X7R 16 V Capacitance (pF) Tolerance 10 000 10% Y5V 16 V Capacitance (pF) Tolerance 100 000 20% X7R 50 V Capacitance (pF) Tolerance 100 10% 1 000 10% 10 000 10% X7R 50 V Capacitance (pF) Tolerance 1 000 10% 10 000 10% 100 000 10% X7R 16 V Capacitance (pF) Tolerance 100 000 10% Y5V 10 V Capacitance (pF) Tolerance 1 000 000 -20% to +80% X7R 10 V Capacitance (pF) Tolerance 1 000 000 10% Y5V 10 V Capacitance (pF) Tolerance 4 700 000 -20% to +80% X7R 50 V Capacitance (pF) Tolerance 1 000 10% 10 000 10% 100 000 10% X7R 16 V Capacitance (pF) Tolerance 1 000 000 10% Y5V 10 V Capacitance (pF) Tolerance 10 000 000 -20% to +80% Microwave NP0 50 V Size Capacitance (pF) 1 10 100 0603 0805 1206 Tolerance 0.25 pF 5% 5% Array (4 x 0603) Size 0612 NP0 50 V Capacitance (pF) Tolerance 100 5% 1 000 5% X7R 25 V Capacitance (pF) Tolerance 10 000 10% X7R 16 V Capacitance (pF) Tolerance 100 000 10% High voltage Size 1808 1812 NP0 3 kV Capacitance (pF) 10 100 X7R 1 kV Tolerance 5% 5% Capacitance (pF) Tolerance 10 000 10% Note: 48 pieces per value (95 pieces for 0402 and 25 pieces for 1812). Ordering code 432204500581 for Phycomp brand product, CC999900000000000 for Yageo brand product 132 HIGH FREQUENCY PRODUCTS HF Product Selection Charts GPS patch antenna and active module GPS patch antenna (CP) Dimensions (mm) 12x12x2 12x12x4 13x13x4 15x15x2 15x15x4 18x18x2 18x18x4 25x25x2 25x25x4 Frequency range Band width* (MHz) Gain* (dBic/Max.) 15752 MHz 4 9 6 5 8 5 10 10 20 -1.5 -1 0 1 2 1 4 5 5.5 Polarization Axial ratio VSWR* <3 Circular < 2.5 Temp. range (C) Packing (Bulk) -40 to 125 CAN4313422021581B CAN4313422031581B CAN 4313422991581B CAN4313423021581B CAN4313423031581B CAN4313424021581B CAN4313424031581B CAN4313425021581B CAN4313425031581B Note: " * " marks that the value depends on the Yageo demoboard GPS patch antenna (LP) Dimensions (mm) Frequency range Band width* (MHz) Gain* (dBi/Max.) Polarization VSWR* Temp. range (C) Packing (Bulk) 15x10x4 16x06x4 15752 MHz 8 1 Linear < 2.5 -40 to 125 CAN4313445011581B CAN4313446011581B Note: " * " marks that the value depends on the Yageo demoboard GPS active module Dimensions (mm) 13x13x5.5 13x13x7.5 15x15x7.5 15x15x7.5 16x16x7.5 19x19x5.5 19x19x7.5 21x15x7.5 28x28x5.5 28x28x7.5 Frequency range 15752 MHz Polarization LNA Gain* (dB/Max.) Noise Figure* (dB/Typical) Current Consumption (mA/Max.) Circular 17 17 15.1 15.1 17 30 30 17 30 30 1.5 1.5 2.5 2.5 1.5 1.5 1.5 1.5 1.5 1.5 5 5 3 3 5 6 6 5 6 6 Note: " * " marks that the value depends on the Yageo demoboard 134 Temp. range (C) Packing (Bulk) -30 to 85 CAN4313434881581B CAN4313434861581B CAN4313434621581B CAN4313435621581B CAN4313435921581B CAN4313437951581B CAN4313437931581B CAN4313435951581B CAN4313439921581B CAN4313439911581B HF Product Selection Charts UHF, Dual-band and Triple-band antenna UHF ceramic antenna Dimensions (mm) Frequency range* 4x12x1.5 6.2x3.0x1.5 400-500 MHz 1.575 GHz 433 MHz 460 MHz 490 MHz 37.5x6.8x0.9 Band width Gain* Polarization (MHz) (dBi/Max.) > 20 100 0.5 1 > 20 0.5 Linear Packing Bulk Tape --CAN4311129200431K ---CAN4311113011582K CAN4313121200431B CAN4311121200431K CAN4313121200461B CAN4311121200461K CAN4313121200491B CAN4311121200491K VSWR* Temp. range (C) < 3.0 < 2.0 -40 to 125 -55 to 125 < 3.0 -55 to 125 Azimuth VSWR* Temp. range (C) Omni-directional < 2.0 < 2.5 -40 to 125 -55 to 125 Azimuth VSWR* Temp. range (C) Omni-directional < 2.0 -55 to 125 Azimuth VSWR* Temp. range (C) Omni-directional < 3.0 -25 to 85 Azimuth VSWR* Temp. range (C) Omni-directional < 2.5 -55 to 125 Bulk --- Azimuth VSWR* Temp. range (C) Bulk Tape Omni-directional < 2.7 -55 to 125 CAN4313118009181B --- Azimuth VSWR* Temp. range (C) Bulk Tape Omni-directional < 3.5 -40 to 85 CAN4313330009191B --- Azimuth Omni-directional TDMA ceramic antenna Dimensions (mm) Frequency range* 12x1.6x4 16.5x14x0.9 800-900 MHz 850-950 MHz Band width Gain* Polarization (MHz) (dBi/Max.) > 20 > 80 0.5 -0.25 Linear Packing Bulk Tape --CNA4311129080871K CAN4313119000871B --- DECT/WCDMA ceramic antenna Dimensions (mm) Frequency range* 8.8x6.8x0.9 1.88-2.1 GHz Band width Gain* Polarization (MHz) (dBi/Max.) > 100 2.0 Linear Packing Bulk --- Tape CAN4311112001881K Wimax ceramic antenna Dimensions (mm) Frequency range* 10x0.6x1.2 2.3-2.7 GHz Band width Gain* Polarization (MHz) (dBi/Max.) > 100 2.0 Linear Packing Bulk --- Tape CAN4311861002371K Dual-band WLAN ceramic antenna Dimensions (mm) Frequency range* 8.7x8.0x0.9 2.45 / 5.2 GHz Band width Gain* Polarization (MHz) (dBi/Max.) > 100 3.5 / 1.5 Linear Packing Tape CAN4311117002521K Dual-band ceramic antenna (900/1800 MHz) Dimensions (mm) Frequency range* 21x12x0.9 880-960 MHz 1710-1880 MHz Band width Gain* Polarization (MHz) (dBi/Max.) > 30 > 170 0.5 -1 0.5 -1 Linear Packing Triple-band metal antenna (900/1800/1900MHz with cable / connector) Dimensions (mm) Frequency range* 35x6x0.4 880-960 MHz 1850-1990 MHz Band width Gain * Polarization (MHz) (dBi/Max.) > 80 > 170 0.5-1.5 1.5-2.5 Linear Packing Note: " * " marks that the value depends on the Yageo demoboard 135 HF Product Selection Charts Bluetooth antenna Bluetooth antennna Dimensions (mm) Frequency range Band width* (MHz) Gain* (dBi/Max.) 2.0x1.2x1.1 2.45 GHz 2.20 GHz 2.30 GHz 2.40 GHz 2.45 GHz 2.50 GHz 2.60 GHz 2.70 GHz 2.80 GHz 2.90 GHz 2.30 GHz 2.40 GHz 2.80 GHz 3.10 GHz 3.30 GHz 3.70 GHz 2.00 GHz 2.10 GHz 2.20 GHz 2.30 GHz 2.40 GHz 2.45 GHz 2.50 GHz 2.45 GHz 2.60 GHz 2.70 GHz 2.45 GHz 2.60 GHz 2.70 GHz 2.80 GHz 2.90 GHz 2.10 GHz 2.20 GHz 2.30 GHz 2.45 GHz 2.50 GHz 2.60 GHz 2.70 GHz 2.80 GHz > 70 3.2x1.6x1.2 5.0x1.0x1.0 5.3x2.0x1.3 7.8x3.6x0.9 7.3x5.5x1.3 8.0x1.0x1.0 VSWR* Temp. range (C) Packing (Tape) 4 < 2.5 -55 to 125 5 < 2.5 -55 to 125 2.45 < 2.0 -25 to 85 < 2.0 -25 to 85 4.1 < 2.5 -55 to 85 1.2 < 2.0 -55 to 125 3 < 2.5 -55 to 125 CAN4311714002454K CAN4311712022453K CAN4311712032453K CAN4311712042453K CAN4311712002453K CAN4311712052453K CAN4311712062453K CAN4311712072453K CAN4311712082453K CAN4311712092453K CAN4311851032453K CAN4311851042453K CAN4311851052453K CAN4311851062453K CAN4311851072453K CAN4311851082453K CAN4311153002001K CAN4311153002101K CAN4311153002201K CAN4311153002301K CAN4311153002401K CAN4311153002451K CAN4311153002501K CAN4311115002451K CAN4311115002601K CAN4311115002701K CAN4311111002451K CAN4311111002601K CAN4311111002701K CAN4311111002801K CAN4311111002901K CAN4311881012453K CAN4311881022453K CAN4311881032453K CAN4311881042453K CAN4311881052453K CAN4311881062453K CAN4311881072453K CAN4311881082453K Azimuth > 100 > 200 5.5 Linear Omnidirectional > 100 Note: " * " marks that the value depends on the Yageo demoboard 136 Polarization HF Product Selection Charts Band pass filter and Low pass filter Band Pass Filter Dimensions (mm) Frequency range* Pass band (MHz) Impedance Insertion loss Ripple 1.6x0.8x0.65 2.45 GHz 2400-2500 2.2 dB 0.5 dB 2.0x1.25x0.85 2.45 GHz 2400-2500 2.0 dB 0.6 dB 2.0x1.25x0.9 2.45 GHz 2400-2500 2.8 dB 0.5 dB 2.0x1.25x1.0 5 GHz 4900-5950 1.5 dB 0.6 dB 2.0x1.25x0.85 5 GHz 4900-5900 2.2 dB 0.6 dB 2.5x2.0x0.95 2.45 GHz 2400-2500 2.5 dB 0.6 dB 50 ohm VSWR* Attenuation (Min.) < 2.0 25 dB @ 1710-1910 MHz 8.5 dB @ 2100 MHz 20 dB @ 4800-5200 MHz 30 dB @ 7200-7500 MHz 40 dB @ 1000-1600 MHz 40 dB @ 4900 MHz 20 dB @ 7200 MHz 40 dB @ 1600 MHz 38 dB @ 3200 MHz 20 dB @ 4800 MHz 25 dB @ 7200 MHz 30 dB @ 1280-3000 MHz 25 dB @ 3300-4000 MHz 25 dB @ 9800-11900 MHz 25 dB @ 6850-7150 MHz 20 dB @ 7500-9000 MHz 40 dB @ 880-960 MHz 30 dB @ 2100 MHz 30 dB @ 4800-5000 MHz 30 dB @ 7200-7500 MHz 40 dB @ 880-960 MHz 30 dB @ 1710-1785 MHz 30 dB @ 1850-1910 MHz 20 dB @ 4800-5000 MHz 30 dB @ 7200-7500 MHz 30 dB @ 1600 MHz 35 dB @ 3200 MHz 25 dB @ 4800-5000 MHz 30 dB @ 7200-7500 MHz 40 dB @ 880-960 MHz 30 dB @ 1710-1785 MHz 20 dB @ 1850-1910 MHz 30 dB @ 4800-5000 MHz 20 dB @ 7200-7500 MHz 20 dB @ 880-960 MHz 20 dB @ 2700 MHz 25 dB @ 4800-5000 MHz 25 dB @ 7200-7500 MHz 2.5x2.0x0.95 2.45 GHz 2400-2500 1.5 dB 0.6 dB 2.5x2.0x0.95 2.45 GHz 2400-2500 2.2 dB 0.6 dB 2.5x2.0x1.1 2.45 GHz 2400-2500 1.5 dB 0.6 dB 2.5x2.0x1.2 2.45 GHz 2400-2500 2.5 dB 0.6 dB Insertion loss Ripple VSWR* 0.45 dB 0.6 dB < 1.5 0.5 dB 0.6 dB < 1.8 0.5 dB 0.6 dB < 2.0 Packing (Tape) CFL4111715012454K CFL4111714032454K CFL4111714992454K CFL4111714015004K CFL4111714035004K CFL4111713022453K CFL4111713032453K CFL4111713182453K CFL4111713052453K CFL4111713072453K Note: " * " marks that the value depends on the Yageo demoboard Low Pass Filter Dimensions (mm) Frequency range* Pass Band (MHz) 1.6x0.8x0.65 2.45 GHz 2400-2500 2.0x1.25x0.85 2.45 GHz 2400-2500 2.0x1.25x0.85 3.5 GHz 3000-4000 Impedance 50 ohm Attenuation (Min.) 25 dB @ 5000 MHz 18 dB @ 7500 MHz 27 dB @ 5000 MHz 25 dB @ 7500 MHz 25 dB @ 10,000 MHz 35 dB @ 6800 MHz 30 dB @ 11,000 MHz (Ref.) Packing (Tape) CFL4111715502454K CFL4111714502454K CFL4111714503504K Note: " * " marks that the value depends on the Yageo demoboard 137 HF Product Selection Charts Balun and Combo Balun Dimensions (mm) Frequency Pass band Impedance range* (MHz) 1.6x0.8x0.65 5 GHz 2.0x1.25x0.80 2.45 GHz 2.0x1.25x0.80 5 GHz 4900-5950 50/100 ohm 50/50 ohm 2400-2500 50/100 ohm 50/200 ohm 4900-5900 50/100 ohm Insertion loss Ripple < 1.2 dB 0.6 dB < 1.0 dB 0.6 dB < 1.2 dB 0.6 dB VSWR* Amplitude balance Phase differential Packing (Tape) 18010 CBA4711715015004K CBA4711714002454K CBA4711714012454K CBA4711714022454K CBA4711714015004K Attenuation (MHz/Min.) Packing (Tape) 1.5 dB 2.0 2.0 dB 2.0 dB Note: " * " marks that the value depends on the Yageo demoboard Bluetooth balanced filter (Filter & Balun combo) Dimensions (mm) 2.0x1.2x0.9 Frequency Pass band Unbalanced range* (MHz) impedance 2.45 GHz 2400-2500 50 ohm Balanced impedance Conjugate match to CSR BC03/ 04/05 series Insertion Amplitude Phase loss balance differential < 3.5 dB < 1.0 dB 2.5x2.0x1.2 138 2.45 GHz 2400-2500 50 ohm Conjugate match to CSR BC02/ 03 series < 3.5 dB 18010 40 dB @ 880-960 25 dB @ 1300-1600 35 dB @ 4800-5000 30 dB @ 7200-7500 40 dB @ 880-960 20 dB @ 1300-1600 35 dB @ 4800-5000 25 dB @ 7200-7500 40 dB @ 880-960 25 dB @ 1300-1600 35 dB @ 4800-5000 30 dB @ 7200-7500 40 dB @ 880-960 25 dB @ 1300-1600 30 dB @ 4800-5000 25 dB @ 7200-7500 40 dB @ 880-960 25 dB @ 1300-1600 35 dB @ 4800-5000 25 dB @ 7200-7500 48 dB @ 880-960 48 dB @ 1710-1880 40 dB @ 1880-1990 20 dB @ 2110-2170 20 dB @ 4800-5000 20 dB @ 7200-7500 CBA4711714982454K CBA4711714772454K CBA4711714882454K CBA4711714672454K CBA4711814572454K CBA4711713932453K HF Product Selection Charts Diplexer Diplexer Dimensions (mm) Frequency range Pass band (MHz) Insertion loss 2400-2500 < 0.7 dB 4900-5900 < 1.6 dB 2400-2500 < 0.65 dB 4900-5900 < 1.1 dB 2400-2500 4900-5900 2400-2500 4900-5900 < 0.7 dB < 0.9 dB < 0.6 dB < 0.9 dB 2400-2500 < 0.5 dB 4900-5900 < 0.9 dB VSWR Attenuation (Min.) < 2.0 17 dB @ 4800-6000 MHz 20 dB @ 7200-7500 MHz 17 dB @ 1800-2500 MHz 20 dB @ 10300-10700 MHz (Ref.) 20 dB @ 4800-6000 MHz 20 dB @ 7200-7500 MHz 15 dB @ 1800-2400 MHz 20 dB @ 2400-2500 MHz 20 dB @ 4900-5900 MHz 20 dB @ 2400-2500 MHz 20 dB @ 4900-5900 MHz 25 dB @ 2400-2500 MHz 20 dB @ 4800-6000 MHz 20 dB @ 7200-7500 MHz 25 dB @ 1800-2500 MHz 25 dB @ 9800-11800 MHz (Ref.) 2.0x1.25x0.75 2.0x1.25x0.85 2.4 / 5 GHz 2.0x1.25x0.85 2.0x1.25x0.9 Packing (Tape) CFL4111714822504K CFL4111714832504K CFL4111714852504K CFL4111714862504K CFL4111714882504K 139 SMD CERAMIC EMI FILTER CAPACITORS X2Y (R) PRODUCTS X2Y(R) Product Selection Charts SMD Ceramic EMI Filter Capacitors X2Y(R) series X5R Y-Capacitor Size 0603 X-Capacitor Capacitance (nF) Voltage rating (V) Capacitance (nF) Voltage rating (V) 220 330 10 10 110 165 20 20 Thickness (mm) Global part number 0.60 0.60 CX 0603 MR X5R 6BB 224 CX 0603 MR X5R 6BB 334 Thickness (mm) Global part number 0.85 0.85 CX 0805 MR NPO 9BB 220 CX 0805 MR NPO 9BB 470 Thickness (mm) Global part number NP0 Y-Capacitor Size 0805 X-Capacitor Capacitance (nF) Voltage rating (V) Capacitance (nF) Voltage rating (V) 0.022 0.047 50 50 0.011 0.023 100 100 X7R Y-Capacitor Size 0603 0805 1206 1210 1410 X-Capacitor Capacitance (nF) Voltage rating (V) Capacitance (nF) Voltage rating (V) 1.5 2.2 4.7 5.6 10 22 47 56 100 4.7 10 15 18 22 39 47 100 180 22 47 100 180 220 390 470 47 100 220 470 560 820 1000 390 100 100 100 50 / 63 50 / 63 25 16 16 10 100 100 50 / 63 50 / 63 25 25 16 16 10 100 50 / 63 50 / 63 25 16 16 16 100 50 / 63 50 / 63 25 25 16 16 50 0.75 1.1 2.4 2.8 5 11 24 28 50 2.4 5 8 9 11 20 24 50 90 11 24 50 90 110 195 235 24 50 110 235 280 410 500 195 200 200 200 100 100 50 25 25 16 200 200 100 100 50 50 25 25 16 200 100 100 50 25 25 25 200 100 100 50 50 25 25 100 0.60 0.85 1.20 1.20 1.20 1.60 1.60 1.60 1.60 1.60 1.30 CX 0603 MR X7R 0BB 152 CX 0603 MR X7R 0BB 222 CX 0603 MR X7R 0BB 472 CX 0603 MR X7R 9BB 562 CX 0603 MR X7R 9BB 103 CX 0603 MR X7R 8BB 223 CX 0603 MR X7R 7BB 473 CX 0603 MR X7R 7BB 563 CX 0603 MR X7R 6BB 104 CX 0805 MR X7R 0BB 472 CX 0805 MR X7R 0BB 103 CX 0805 MR X7R 9BB 153 CX 0805 MR X7R 9BB 183 CX 0805 MR X7R 8BB 223 CX 0805 MR X7R 8BB 393 CX 0805 MR X7R 7BB 473 CX 0805 MR X7R 7BB 104 CX 0805 MR X7R 6BB 184 CX 1206 MK X7R 0BB 223 CX 1206 MK X7R 9BB 473 CX 1206 MK X7R 9BB 104 CX 1206 MK X7R 8BB 184 CX 1206 MK X7R 7BB 224 CX 1206 MK X7R 7BB 394 CX 1206 MK X7R 7BB 474 CX 1210 MK X7R 0BB 473 CX 1210 MK X7R 9BB 104 CX 1210 MK X7R 9BB 224 CX 1210 MK X7R 8BB 474 CX 1210 MK X7R 8BB 564 CX 1210 MK X7R 7BB 824 CX 1210 MK X7R 7BB 105 CX 1410 MK X7R 9BB 394 Note: 1. Special values are available on request 2. Ordering codes for preferred versions (20% tolerance, 180 mm reel). For packing and tolerance information, see section "Thickness classes and packing quantities" on next page 142 X2Y(R) Product Selection Charts Ordering information Global part number Ordering example: CX0603MKX7R6BB104 CX 0603 M K X7R 6 B B 104 Series name (code 1-2) CX = X2Y (R) series Capacitance value (code 15-17) 104 = 100 000 pF (2 significant digits+number of zeros; the 3rd digit signifies the multiplying factor, and letter R is decimal point) 0=x1 1 = x 10 1 2 = x 10 2 3 = x 10 3 4 = x 10 4 5 = x 10 5 6 = x 10 6 Size code (code 3-6) EIA mm 0603 (1608M) 0805 (2012M) 1206 (3216M) 1210 (3225M) 1410 (3625M) 1812 (4632M) Capacitance tolerance (code 7) M = 20% Process code (code 14) B = BME Packing style (code 8) R = Paper tape reel O7" K = Embossed plastic tape reel O7" Termination (code 13) B = Ni-barrier TC material (code 9-11) NP0 X5R X7R Rated voltage (code 12) 5 = 6.3 V 7 = 16 V 8 = 25 V 9 = 50 V 0 = 100 V Thickness classes and packing quantities Quantity per reel Thickness Classification (mm) 0.60 0.10 0.85 0.10 1.20 0.15 1.30 0.20 1.60 0.15 8 mm tape width O180mm / 7" Paper Blister 4 000 4 000 ------- ----2 500 2 500 2 500 143 MULTILAYER CHIP VARISTORS MLV Product Selection Charts Case dimensions and specification for 0402 Case dimensions Case size designation T L1 W Tmin Tmax L2 / L3 min L2 / L3 max L4 min 0402 0603 0805 1206 1.0 0.10 1.6 0.20 2.0 0.10 3.2 0.15 0.5 0.10 0.8 0.10 1.25 0.10 1.6 0.15 0.45 0.70 0.70 0.70 0.55 0.90 0.90 0.90 0.15 0.20 0.25 0.25 0.30 0.60 0.75 0.75 0.40 0.40 0.55 1.40 W L2 L4 Dimensions in mm Inch-based L3 L1 Size 0402 Global part number VRS0402MR55R651N VRS0402SR55R601N VRS0402MR55R331N VRS0402MR55R201N VRS0402MR55R101N VRS0402SR55R101N VRS0402SR55R820N VRS0402SR55R680N VRS0402SR55R500N VRS0402SR55R330N VRS0402SR55R220N VRS0402SR55R100N VRS0402SR55R030N VRS0402LR090201N VRS0402KR090101N VRS0402KR090500N VRS0402SR090500N VRS0402SR090330N VRS0402LR110181N VRS0402KR140161N VRS0402MR140161N VRS0402LR140161N VRS0402SR140121N VRS0402SR140101N VRS0402SR140500N VRS0402KR160121N VRS0402SR180121N VRS0402KR180900N VRS0402KR180820N VRS0402MR180500N VRS0402SR180500N VRS0402SR180400N VRS0402SR180270N VRS0402SR180150N VRS0402SR180120N VRS0402SR180100N VRS0402SR180030N VRS0402KR220820N VRS0402KR260550N VRS0402KR300400N VRS0402SR300030N 146 Varistor voltage/ Breakdown voltage DC @ 1 mA (V) 7.2 to 10.8 10 to 14 7.2 to 10.8 7.2 to 10.8 7.2 to 10.8 10 to 14 10 to 14 10 to 14 10 to 14 10 to 14 10 to 14 10 to 14 50 to 80 10.2 to 13.8 10.2 to 13.8 10.2 to 13.8 11 to 17 11 to 17 12.75 to 17.25 16.2 to 19.8 14.4 to 21.6 15.3 to 20.7 18 to 24 18 to 24 18 to 24 19.8 to 24.2 24 to 32 21.6 to 26.4 21.6 to 26.4 19.8 to 24.2 24 to 32 24 to 3s2 24 to 32 24 to 32 24 to 32 24 to 32 50 to 80 24.3 to 29.7 29.7 to 36.3 35.1 to 42.9 48 to 58 Max. continuous voltage/ Clamping voltage Working voltage D.C (V / Max.) 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 9 9 9 9 9 11 14 14 14 14 14 14 16 18 18 18 18 18 18 18 18 18 18 18 22 26 30 30 8/20 s (V / Max.) (A) 14 22 15 15 15 23 22 22 23 22 22 22 150 22 22 22 25 25 27 33 33 1 33 40 38 38 40 45 44 45 48 52 50 50 50 46 58 150 49 60 71 96 Peak current Resistance R.T. (15 to 35C ) Capacitance @ 1 V (rms) 8/20 s Voltage Resistance (pF) (A / Max.) (V) (M / Min.) 1 KHz 1 MHz 30 1 650 390 65 1 600 360 30 1 330 200 20 1 200 130 20 1 100 60 15 10 100 60 10 1 82 47 8 1 68 40 6 10 50 30 4 1 33 20 2 1 22 12 2 1 10 5.5 2 10 3 --20 1 200 120 20 1 100 60 20 1 50 30 5 1 50 30 4 1 33 20 20 1 180 110 20 1 160 96 20 3 1 160 96 20 1 160 96 20 10 120 72 15 1 100 60 7 1 50 30 18 1 120 72 20 1 120 72 14 1 90 54 10 1 82 50 5 1 50 30 5 1 50 30 4 1 40 22 4 1 27 15 3 1 15 9 10 10 120 72 3 10 10 6 2 10 3 2 14 1 82 50 10 1 55 33 8 1 40 24 2 10 3 2 MLV Product Selection Charts Specification for 0603 to 1206 Size 0603 Global part number VRS0603MR55R801N VRS0603SR55R801N VRS0603MR55R681N VRS0603SR55R471N VRS0603MR55R301N VRS0603SR55R201N VRS0603SR55R181N VRS0603SR55R300N VRS0603SR55R220N VRS0603SR55R030N VRS0603SR070331N VRS0603LR090681N VRS0603MR090351N VRS0603LR110481N VRS0603SR120150N VRS0603LR140361N VRS0603SR140150N VRS0603KR180301N VRS0603LR180251N VRS0603SR180121N VRS0603SR180100N VRS0603SR180030N VRS0603KR220241N VRS0603KR220101N VRS0603KR260251N VRS0603KR260201N VRS0603KR300121N VRS0603KR380101N VRS0603KR450800N VRS0603SR111300N Varistor voltage/ Breakdown voltage DC @ 1 mA (V) 7.2 to 10.8 10 to 14 7.2 to 10.8 10 to 14 7.2 to 10.8 10 to 14 10 to 14 10 to 14 11 to 17 50 to 80 10 to 14 10.2 to 13.8 9.6 to 14.4 12.75 to 17.25 24 to 32 15.3 to 20.7 18 to 24 21.6 to 26.4 20.4 to 27.6 24 to 32 90 to 160 50 to 80 24.3 to 29.7 24.3 to 29.7 29.7 to 36.3 29.7 to 36.3 35.1 to 42.9 42.3 to 51.7 50.4 to 61.6 130 to 160 Max. continuous voltage/ Clamping voltage Working voltage D.C (V / Max.) 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 7 9 9 11 12 14 14 18 18 18 18 18 22 22 26 26 30 38 45 110 8/20 s (V / Max.) (A) 15 17 15 19 15 15 20 25 22 150 22 22 22 22 55 1 33 42 44 42 50 225 150 46 46 58 60 70 85 100 300 Peak current Resistance R.T. (15 to 35C ) Capacitance @ 1 V (rms) 8/20 s Voltage Resistance (pF) (A / Max.) (V) (M / Min.) 1 KHz 1 MHz 30 1 800 480 30 1 800 480 30 1 680 410 30 1 470 280 30 1 300 180 30 1 200 120 30 1 180 100 10 1 30 18 5 1 22 12 3 10 3 --30 1 330 200 30 1 680 410 30 1 350 220 30 1 480 290 5 10 15 9 3 30 1 360 216 5 1 15 9 30 1 300 180 30 0.3 250 -20 1 120 72 5 1 10 6 1 10 3 2 30 1 240 144 30 1 100 60 30 1 250 160 30 1 200 120 30 1 120 72 20 1 100 60 20 1 80 48 5 1 30 18 Size 0805 Global part number VRS0805MR55R162N VRS0805KR180551N Varistor voltage/ Breakdown voltage DC @ 1 mA (V) 6.4 to 9.6 21.6 to 26.4 Max. continuous voltage/ Clamping voltage Working voltage D.C (V / Max.) 5.5 18 8/20 s (V / Max.) (A) 18 1 39 Peak current Leakage current R.T. (15 to 35C ) Capacitance @ 1 V (rms) 8/20 s Voltage Resistance (pF) (A / Max.) (V) (M / Min.) 1 KHz 1 MHz 80 1600 -3 1 100 550 -- Size 1206 Global part number VRS1206LR140351N VRS1206LR300401N VRS1206KR560251N VRS1206KR680251N Varistor voltage/ Breakdown voltage DC @ 1 mA (V) 15.3 to 20.7 33.1 to 44.8 61 to 77 76 to 90 Max. continuous voltage/ Clamping voltage Working voltage D.C (V / Max.) 14 30 56 68 8/20 s (V / Max.) (A) 32 67 1 110 130 Peak current Leakage current R.T. (15 to 35C ) Capacitance @ 1 V (rms) 8/20 s Voltage Resistance (pF) (A / Max.) (V) (M / Min.) 1 KHz 1 MHz 30 1 350 -120 1 400 -3 180 10 250 150 180 10 250 150 147 MLV Product Selection Charts Ordering information for 0402 to 1206 Global part number Ordering example: VRS0402KR55R680N VR S 0402 K R 55R 680 N Series name (code 1-2) VR = Varistor Process code (code 16) N = Normal Chip type (code 3) S = Single chip Capacitance value (code 13-15) 680 = 68 pF (2 significant digits+number of zeros; the 3rd digit signifies the multiplying factor, and letter R is decimal point) 0=x1 1 = x 10 1 Size code (code 4-7) 0402 0603 0805 1206 Capacitance tolerance (code 8) K = 10% L = 15% M = 20 % S = Special range Packing style (code 9) R = paper tape reel O7 inch Working voltage (code 10-12) 55R = 5.5 V 090 = 9 V 110 = 11 V 150 = 15 V 160 = 16 V 180 = 18 V 220 = 22 V 260 = 26 V 300 = 30 V 380 = 38 V 450 = 45 V 560 = 56 V 680 = 68 V 111 = 110 V Thickness classification and packing quantities 8 mm tape width amount per reel Type Thickness classification (mm) 0402 0.50 0.05 10 000 0603 0.80 0.10 4 000 0805 0.80 0.10 4 000 1206 0.80 0.10 4 000 180 mm / 7" Paper 148 YAGEO - A GLOBAL COMPANY ASIA Beijing, China Dongguan, China Hong Kong, China Suzhou, China Tel. +86 10 851 20810 Fax. +86 10 851 20200 Tel. +86 769 8772 0275 Fax. +86 769 8791 0053 Tel. +852 2342 6833 Fax. +852 2342 6588 Tel. +86 512 6825 5568 Fax. +86 512 6825 5386 Tokyo, Japan Kyunggi-Do, Korea Kuala Lumpur, Malaysia Singapore Tel. +81 3 5833 3331 Fax. +81 3 5833 3116 Tel. +82 31 712 4797 Fax. +82 31 712 5866 Tel. +60 3 8060 8864 Fax. +60 3 8068 2700 Tel. +65 6244 7800 Fax. +65 6244 4943 Taipei, Taiwan Tel. +886 2 2917 7555 Fax. +886 2 2910 9056 EUROPE Roermond, Benelux Brno, Czech Republic Paris, France Hamburg, Germany Tel. +31 475 385 428 Fax. +31 475 385 589 Tel. +420 7 2317 5035 Fax. +420 5 4325 4936 Tel. +33 1 5551 8404 Fax. +33 1 5551 8407 Tel. +49 4121 870 189 Fax. +49 4121 870 271 Budapest, Hungary Milan, Italy Moscow, Russian Federation Barcelona, Spain Tel. +36 13 097 280 Fax. +36 13 097 281 Tel. +39 33 5140 9233 Fax. +39 02 2411 3051 Tel. +7 916 625 92 38 Fax. +7 495 374 81 87 Tel. +34 93 212 3929 Fax. +39 02 2411 3051 Croydon, UK Tel. +44 208 781 1844 Fax. +44 208 781 1845 NORTH AMERICA San Jose, U.S.A. Tel. +1 408 240 6200 Fax. +1 408 240 6201 For more detailed and always up-to-date contact details of sales offices, distributors and representatives, please go to our web site at www.yageo.com (c) YAGEO Corporation All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights. Printed in Taiwan Document order number: 2838 100 00112 Date of release: December 2008