LTM8033 Ultralow Noise EMC 36VIN, 3A DC/DC Module Regulator DESCRIPTION FEATURES n n n n n n n n n n n Complete Step-Down Switch Mode Power Supply Wide Input Voltage Range: 3.6V to 36V 3A Output Current 0.8V to 24V Output Voltage EN55022 Class B Compliant Current Share Multiple LTM8033 Regulators for More Than 3A Output Selectable Switching Frequency: 200kHz to 2.4MHz Current Mode Control SnPb or RoHS Compliant Finish Programmable Soft-Start Compact Package (11.25mm x 15mm x 4.32mm) Surface Mount LGA and (11.25mm x 15mm x 4.92mm) BGA Packages APPLICATIONS n n n n n Automotive Battery Regulation Power for Portable Products Distributed Supply Regulation Industrial Supplies Wall Transformer Regulation The LTM(R)8033 is an electromagnetic compatible (EMC) 36V, 3A DC/DC Module(R) buck converter designed to meet the radiated emissions requirements of EN55022. Conducted emission requirements can be met by adding standard filter components. Included in the package are the switching controller, power switches, inductor, filters and all support components. Operating over an input voltage range of 3.6V to 36V, the LTM8033 supports an output voltage range of 0.8V to 24V, and a switching frequency range of 200kHz to 2.4MHz, each set by a single resistor. Only the bulk input and output filter capacitors are needed to finish the design. The LTM8033 is packaged in a compact (11.25mm x 15mm x 4.32mm) overmolded land grid array (LGA) and ball grid array (BGA) package suitable for automated assembly by standard surface mount equipment. The LTM8033 is available with SnPb (BGA) or RoHS compliant terminal finish. L, LT, LTC, LTM, Linear Technology, the Linear logo, Module and Burst Mode are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. TYPICAL APPLICATION Ultralow Noise 12V/3A DC/DC Module Regulator 80 LTM8033 VIN* 20V TO 36V VIN 2.2F 1F EMI Performance VOUT 12V 3A VOUT 70 60 RUN/SS AUX FIN BIAS 40 PGOOD 30 SHARE 47F RT SYNC GND ADJ 41.2k 20 10 0 34.8k f = 850kHz 50 30 226.2 422.4 618.6 814.8 1010 324.3 520.5 716.7 912.9 128.1 FREQUENCY (MHz) 8033 TA01b 8033 TA01a * RUNNING VOLTAGE RANGE. PLEASE REFER TO THE APPLICATIONS INFORMATION SECTION FOR START-UP DETAILS. 8033fb For more information www.linear.com/LTM8033 1 LTM8033 ABSOLUTE MAXIMUM RATINGS (Note 1) VIN, FIN, RUN/SS Voltage .........................................36V ADJ, RT, SHARE Voltage .............................................6V VOUT, AUX .................................................................25V PGOOD, SYNC ..........................................................30V BIAS ..........................................................................25V Maximum Junction Temperature (Note 2) ........... 125C Solder Temperature .............................................. 245C PIN CONFIGURATION TOP VIEW TOP VIEW GND SYNC GND SYNC 8 8 RUN/SS ADJ PGOOD BANK 3 7 RUN/SS ADJ PGOOD FIN 6 BANK 2 BANK 2 5 5 GND GND 4 3 BIAS 4 AUX 3 BANK 1 BIAS AUX BANK 4 BANK 1 BANK 4 VOUT VIN 2 VOUT VIN 1 1 A B FIN SHARE RT 6 2 BANK 3 7 SHARE RT C D E F G H J K A L B C D E F G H J K L BGA PACKAGE 76-LEAD (15mm x 11.25mm x 4.92mm) LGA PACKAGE 76-LEAD (15mm x 11.25mm x 4.32mm) TJMAX = 125C, JA = 15.4C/W, JCbottom = 5.2C/W, JB = 9.8C/W, JCtop = 16.7C/W VALUES DERIVED FROM A 4 LAYER 6.35cm x 6.35cm PCB WEIGHT = 2.2g TJMAX = 125C, JA = 15.4C/W, JCbottom = 5.2C/W, JB = 9.8C/W, JCtop = 16.7C/W VALUES DERIVED FROM A 4 LAYER 6.35cm x 6.35cm PCB WEIGHT = 2.2g ORDER INFORMATION PART MARKING* PART NUMBER PAD OR BALL FINISH DEVICE FINISH CODE PACKAGE TYPE MSL RATING TEMPERATURE RANGE (Note 2) LTM8033EV#PBF Au (RoHS) LTM8033V e4 LGA 3 -40C to 125C LTM8033IV#PBF Au (RoHS) LTM8033V e4 LGA 3 -40C to 125C LTM8033MPV#PBF Au (RoHS) LTM8033V e4 LGA 3 -55C to 125C LTM8033EY#PBF SAC305 (RoHS) LTM8033Y e1 BGA 3 -40C to 125C LTM8033IY#PBF SAC305 (RoHS) LTM8033Y e1 BGA 3 -40C to 125C LTM8033IY SnPb (63/67) LTM8033Y e0 BGA 3 -40C to 125C LTM8033MPY#PBF SAC305 (RoHS) LTM8033Y e1 BGA 3 -55C to 125C LTM8033MPY SnPb (63/67) LTM8033Y e0 BGA 3 -55C to 125C Consult Marketing for parts specified with wider operating temperature ranges. *Device temperature grade is indicated by a label on the shipping container. Pad or ball finish code is per IPC/JEDEC J-STD-609. * Recommended LGA and BGA PCB Assembly and Manufacturing Procedures: www.linear.com/umodule/pcbassembly * Terminal Finish Part Marking: www.linear.com/leadfree * LGA and BGA Package and Tray Drawings: www.linear.com/packaging 8033fb 2 For more information www.linear.com/LTM8033 LTM8033 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VIN = 12V, RUN/SS = 12V unless otherwise noted (Note 2). PARAMETER CONDITIONS MIN Minimum Input Voltage TYP Output DC Voltage 0A < IOUT < 3A, RADJ Open, VIN = 24V 0A < IOUT < 3A, RADJ = 16.5k, VIN = 32V Output DC Current VIN = 24V Quiescent Current into VIN RUN/SS = 0.2V Not Switching BIAS = 0V, Not Switching Quiescent Current into BIAS Line Regulation MAX 3.6 l 0.8 24 0 UNITS V V V 3 A 0.01 30 100 1 60 150 A A A RUN/SS = 0.2V Not Switching BIAS = 0V, Not Switching 0.01 75 0 0.5 120 5 A A A 5.5V < VIN < 36V 0.3 % Load Regulation 0A < IOUT < 3A, VIN = 24V 0.4 % Output RMS Voltage Ripple VIN = 24V, 0A < IOUT < 3A 5 mV Switching Frequency RT = 45.3k 780 Voltage at ADJ Pin Current Out of ADJ Pin l 775 ADJ = 1V, VOUT = 0V kHz 805 2 Minimum BIAS Voltage for Proper Operation RUN/SS Pin Current 790 RUN/SS = 2.5V RUN/SS Input High Voltage mV A 2 2.8 V 5 10 A 2.5 V RUN/SS Input Low Voltage 0.2 730 V PGOOD Threshold (at ADJ) VOUT Rising PGOOD Leakage Current PGOOD = 30V, RUN/SS = 0V PGOOD Sink Current PGOOD = 0.4V 200 SYNC Input Low Threshold fSYNC = 550kHz 0.5 SYNC Input High Threshold fSYNC = 550kHz SYNC Bias Current SYNC = 0V 0.1 A 500kHz Narrowband Conducted Emissions 24VIN, 3.3VOUT, IOUT = 3A, 5H LISN 0.1 mV 1 735 A A V 0.7 V 89 dBV 1MHz Narrowband Conducted Emissions 69 dBV 3MHz Narrowband Conducted Emissions 51 dBV Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTM8033E is guaranteed to meet performance specifications from 0C to 125C internal. Specifications over the full -40C to 125C internal operating temperature range are assured by design, characterization and correlation with statistical process controls. The LTM8033I is guaranteed to meet specifications over the full -40C to 125C internal operating temperature range. The LTM8033MP is guaranteed to meet specifications over the full -55C to 125C internal operating temperature range. Note that the maximum internal temperature is determined by specific operating conditions in conjunction with board layout, the rated package thermal resistance and other environmental factors. 8033fb For more information www.linear.com/LTM8033 3 LTM8033 TYPICAL PERFORMANCE CHARACTERISTICS 90 5VIN 85 12VIN 90 36VIN 24VIN 65 95 12VIN 24VIN 36VIN 75 70 65 0 500 1000 1500 2000 2500 OUTPUT CURRENT (mA) 50 3000 0 500 1000 1500 2000 2500 OUTPUT CURRENT (mA) 24VIN 75 70 65 24VIN 85 85 80 80 75 70 65 75 70 65 55 55 50 50 50 3000 60 0 500 1000 1500 2000 2500 OUTPUT CURRENT (mA) 80 45 BIAS CURRENT (mA) 40 35 5VIN 30 25 20 12VIN 15 24VIN 10 5 0 0 500 1000 1500 2000 2500 LOAD CURRENT (mA) Bias Current vs Load Current, 3.3VOUT 3000 8033 G07 40 70 35 60 30 50 5VIN 40 30 12VIN 20 24VIN 10 36VIN 0 500 1000 1500 2000 2500 OUTPUT CURRENT (mA) 0 500 1000 1500 2000 2500 LOAD CURRENT (mA) Bias Current vs Load Current, 5VOUT 12VIN 25 20 24VIN 15 10 36VIN 5 36VIN 0 3000 8033 G06 BIAS CURRENT (mA) 50 3000 8033 G05 Bias Current vs Load Current, 2.5VOUT 3000 36VIN 90 36VIN 55 1000 1500 2000 2500 OUTPUT CURRENT (mA) 1000 1500 2000 2500 OUTPUT CURRENT (mA) 18VOUT Efficiency 60 500 500 8033 G03 60 0 0 95 8033 G04 BIAS CURRENT (mA) 65 50 3000 EFFICIENCY (%) 36VIN 80 70 12VOUT Efficiency 90 EFFICIENCY (%) EFFICIENCY (%) 95 12VIN 85 75 8033 G02 8VOUT Efficiency 90 24VIN 55 8033 G01 95 36VIN 80 60 55 55 12VIN 90 60 60 5VOUT Efficiency 85 80 70 50 5.5VIN 85 80 75 3.3VOUT Efficiency EFFICIENCY (%) 2.5VOUT Efficiency EFFICIENCY (%) EFFICIENCY (%) 95 TA = 25C, unless otherwise noted. 3000 8033 G08 0 0 500 1000 1500 2000 2500 LOAD CURRENT (mA) 3000 8033 G09 8033fb 4 For more information www.linear.com/LTM8033 LTM8033 TYPICAL PERFORMANCE CHARACTERISTICS Bias Current vs Load Current, 8VOUT Bias Current vs Load Current, 12VOUT 90 80 90 80 70 80 12VIN 50 40 30 24VIN 20 36VIN 10 0 0 500 1000 1500 2000 2500 LOAD CURRENT (mA) 50 40 24VIN 30 36VIN 20 0 60 36VIN 50 40 30 20 10 3000 Bias Current vs Load Current, 18VOUT 70 60 BIAS CURRENT (mA) 60 BIAS CURRENT (mA) 70 BIAS CURRENT (mA) TA = 25C, unless otherwise noted. 10 0 500 1000 1500 2000 2500 LOAD CURRENT (mA) 8033 G10 0 3000 0 500 1000 1500 2000 2500 LOAD CURRENT (mA) 8033 G12 8033 G11 Input Current vs Input Voltage Output Shorted Input Current vs Output Current 2.5VOUT 1000 3000 2500 2500 2000 2000 Input Current vs Output Current 3.3VOUT INPUT CURRENT (mA) INPUT CURRENT (mA) 800 700 600 500 400 300 200 1500 5VIN 1000 12VIN 500 0 10 20 30 INPUT VOLTAGE (V) 0 40 500 1000 1500 2000 2500 OUTPUT CURRENT (mA) 8033 G13 1600 12VIN 24VIN 3000 0 500 1000 1500 2000 2500 OUTPUT CURRENT (mA) Input Current vs Output Current 5VOUT 2500 3000 8033 G15 8033 G14 Input Current vs Output Current 8VOUT 1800 Input Current vs Output Current 12VOUT 1600 2000 1000 12VIN 800 600 24VIN 400 0 500 1000 1500 2000 2500 OUTPUT CURRENT (mA) 1500 12VIN 1000 24VIN 36VIN 3000 8033 G16 0 0 500 1200 24VIN 1000 800 36VIN 600 400 500 36VIN 200 1400 INPUT CURRENT (mA) 1200 INPUT CURRENT (mA) INPUT CURRENT (mA) 1000 0 1400 0 5.5VIN 36VIN 36VIN 0 1500 500 24VIN 100 0 INPUT CURRENT (mA) 900 1000 1500 2000 2500 OUTPUT CURRENT (mA) 3000 8033 G17 200 0 0 500 1000 1500 2000 2500 OUTPUT CURRENT (mA) 3000 8033 G18 8033fb For more information www.linear.com/LTM8033 5 LTM8033 TYPICAL PERFORMANCE CHARACTERISTICS 1600 35 1400 30 1200 36VIN 1000 800 600 25 20 15 0 500 1000 1500 2000 2500 OUTPUT CURRENT (mA) 0 3000 3.8 3.6 3.4 TO RUN OR SS CONTROLLED START 3.2 5 10 OUTPUT VOLTAGE (V) 0 3.0 15 0 500 1000 1500 2000 2500 LOAD CURRENT (mA) 8033 G20 8033 G19 Minimum Required Input Voltage vs Load Current, 3.3VOUT 8.0 3000 8033 G21 Minimum Required Input Voltage vs Load Current, 5VOUT Minimum Required Input Voltage vs Load Current, 8VOUT 10.5 7.5 5.5 7.0 5.0 RUN/SS CONTROLLED START 4.5 4.0 TO RUN 3.5 10.0 6.5 TO START, WITH RUN = VIN INPUT VOLTAGE (V) TO START, WITH RUN = VIN INPUT VOLTAGE (V) INPUT VOLTAGE (V) TO START, WITH RUN = VIN 4.0 5 200 6.0 4.4 Minimum Required Input Voltage vs Load Current, 2.5VOUT 4.2 10 400 0 Minimum Required Input Voltage vs Output Voltage, IOUT = 3A INPUT VOLTAGE (V) 40 INPUT VOLTAGE (V) INPUT CURRENT (mA) 1800 Input Current vs Output Current 18VOUT TA = 25C, unless otherwise noted. 6.0 5.5 5.0 4.5 TO RUN OR RUN/SS CONTROLLED START 4.0 TO START, WITH RUN = VIN 9.5 TO RUN OR RUN/SS CONTROLLED START 9.0 8.5 3.5 3.0 0 500 1000 1500 2000 2500 LOAD CURRENT (mA) 3.0 3000 0 500 1000 1500 2000 2500 LOAD CURRENT (mA) 8033 G22 Minimum Required Input Voltage vs Load Current, 18VOUT 80 30 19 28 70 26 60 TO RUN OR START 16 15 24 13 14 500 1000 1500 2000 2500 LOAD CURRENT (mA) 3000 8033 G25 12 3000 Radiated Emissions, 36VIN, 24VOUT at 1.5A Load 40 30 18 16 0 1000 1500 2000 2500 LOAD CURRENT (mA) 50 20 14 12 TO START, WITH RUN = VIN 22 dBV/m INPUT VOLTAGE (V) 17 500 8033 G24 20 18 0 8033 G23 Minimum Required Input Voltage vs Load Current, 12VOUT INPUT VOLTAGE (V) 8.0 3000 TO RUN 20 RUN/SS CONTROLLED START 10 0 500 1000 1500 2000 2500 LOAD CURRENT (mA) 3000 8033 G26 0 30 226.2 422.4 618.6 814.8 1010 324.3 520.5 716.7 128.1 912.9 FREQUENCY (MHz) 8033 G27 8033fb 6 For more information www.linear.com/LTM8033 LTM8033 TYPICAL PERFORMANCE CHARACTERISTICS 80 Radiated Emissions, 36VIN, 1.2VOUT at 3A Load 40 Temperature Rise vs Load Current, 2.5VOUT 40 35 60 30 30 40 30 20 25 36VIN 20 15 5VIN 10 5 10 0 226.2 422.4 618.6 814.8 1010 324.3 520.5 716.7 128.1 912.9 FREQUENCY (MHz) 45 12VIN 24VIN 36VIN 20 15 12VIN 10 24VIN 0 500 1000 1500 2000 2500 LOAD CURRENT (mA) 8033 G29 8033 G28 Temperature Rise vs Load Current, 5VOUT 60 TEMPERATURE RISE (C) 30 36VIN 25 20 12VIN 15 10 8033 G30 Temperature Rise vs Load Current, 8VOUT 0 500 40 30 36VIN 20 10 24VIN 5 1000 1500 2000 2500 LOAD CURRENT (mA) 0 3000 12VIN 24VIN 0 500 1000 1500 2000 2500 LOAD CURRENT (mA) Temperature Rise vs Load Current, 12VOUT 70 Temperature Rise vs Load Current, 18VOUT 60 TEMPERATURE RISE (C) 60 50 40 30 36VIN 20 24VIN 50 36VIN 40 30 20 10 10 0 3000 8033 G32 8033 G31 70 3000 50 35 0 25 0 500 1000 1500 2000 2500 3000 3500 LOAD CURRENT (mA) 0 Temperature Rise vs Load Current, 3.3VOUT 5 40 TEMPERATURE RISE (C) 30 TEMPERATURE RISE (C) 0 TEMPERATURE RISE (C) 35 TEMPERATURE RISE (C) 70 50 dBV/m TA = 25C, unless otherwise noted. 0 500 1000 1500 2000 2500 LOAD CURRENT (mA) 3000 0 0 8033 G33 500 1000 1500 LOAD CURRENT (mA) 2000 8033 G34 8033fb For more information www.linear.com/LTM8033 7 LTM8033 PIN FUNCTIONS VOUT (Bank 1): Power Output Pins. Apply the output filter capacitor and the output load between these pins and GND pins. GND (A8, Bank 2): Tie these GND pins to a local ground plane below the LTM8033 and the circuit components. Return the feedback divider (RADJ) to this net. FIN (Bank 3): Filtered Input. This is the node after the input EMI filter. Apply the capacitor recommended by Table 1. Additional capacitance may be applied if there is a need to modify the behavior of the integrated EMI filter; otherwise, leave these pins unconnected. See the Applications Information section for more details. VIN (Bank 4): The VIN pin supplies current to the LTM8033's internal regulator and to the internal power switch. This pin must be locally bypassed with an external, low ESR capacitor; see Table 1 for recommended values. Ensure that VIN + BIAS is less than 56V. SHARE (Pin A6): Tie this to the SHARE pin of another LTM8033 when paralleling the outputs. Otherwise, do not connect. ADJ (Pin A7): The LTM8033 regulates its ADJ pin to 0.79V. Connect the adjust resistor from this pin to ground. The value of RADJ is given by the equation RADJ = 394.21/(VOUT - 0.79), where RADJ is in k. RT (Pin B6): The RT pin is used to program the switching frequency of the LTM8033 by connecting a resistor from this pin to ground. The Applications Information section of the data sheet includes a table to determine the resistance value based on the desired switching frequency. Minimize capacitance at this pin. SYNC (Pin B8): This is the external clock synchronization input. Ground this pin for low ripple Burst Mode(R) operation at low output loads. Tie to a stable voltage source greater than 0.7V to disable Burst Mode operation. Do not leave this pin floating. Tie to a clock source for synchronization. Clock edges should have rise and fall times faster than 1s. See the Synchronization section in the Applications Information section. PGOOD (Pin B7): The PGOOD pin is the open-collector output of an internal comparator. PGOOD remains low until the ADJ pin is greater than 90% of the final regulation voltage. PGOOD output is valid when VIN is above 3.6V and RUN/SS is high. If this function is not used, leave this pin floating. AUX (Pin G3): Low Current Voltage Source for BIAS. In many designs, the BIAS pin is simply connected to VOUT. The AUX pin is internally connected to VOUT and is placed adjacent to the BIAS pin to ease printed circuit board routing. Although this pin is internally connected to VOUT, it is not intended to deliver a high current, so do not connect this pin to the load. If this pin is not tied to BIAS, leave it floating. BIAS (Pin G4): The BIAS pin connects to the internal power bus. Connect to a power source greater than 2.8V and less than 25V. If the output is greater than 2.8V, connect this pin there. If the output voltage is less, connect this to a voltage source between 2.8V and 25V but ensure that VIN + BIAS is less than 56V. RUN/SS (Pin G8): Pull the RUN/SS pin below 0.2V to shut down the LTM8033. Tie to 2.5V or more for normal operation. If the shutdown feature is not used, tie this pin to the VIN pin. RUN/SS also provides a soft-start function; see the Applications Information section. 8033fb 8 For more information www.linear.com/LTM8033 LTM8033 BLOCK DIAGRAM VIN VOUT 8.2H EMI FILTER 1F 15pF 499k FIN AUX BIAS RUN/SS SHARE CURRENT MODE CONTROLLER SYNC GND RT PGOOD ADJ 8033 BD 8033fb For more information www.linear.com/LTM8033 9 LTM8033 OPERATION The LTM8033 is a standalone nonisolated step-down switching DC/DC power supply that can deliver up to 3A of output current. It is an EMC product; its radiated emissions are so quiet that it can pass the stringent requirements of EN55022 class B as a stand alone product. This Module provides a precisely regulated output voltage programmable via one external resistor from 0.8V to 24V. The input voltage range is 3.6V to 36V. Given that the LTM8033 is a step-down converter, make sure that the input voltage is high enough to support the desired output voltage and load current. As shown in the Block Diagram, the LTM8033 contains an EMI filter, current mode controller, power switching element, power inductor, power Schottky diode and a modest amount of input and output capacitance. The LTM8033 is a fixed frequency PWM regulator. The switching frequency is set by simply connecting the appropriate resistor value from the RT pin to GND. An internal regulator provides power to the control circuitry. The bias regulator normally draws power from the VIN pin, but if the BIAS pin is connected to an external voltage higher than 2.8V, bias power will be drawn from the external source (typically the regulated output voltage). This improves efficiency. The RUN/SS pin is used to place the LTM8033 in shutdown, disconnecting the output and reducing the input current to less than 1A. To further optimize efficiency, the LTM8033 automatically switches to Burst Mode operation in light load situations. Between bursts, all circuitry associated with controlling the output switch is shut down reducing the input supply current to 50A in a typical application. The oscillator reduces the LTM8033's operating frequency when the voltage at the ADJ pin is low. This frequency foldback helps to control the output current during startup and overload. The LTM8033 contains a power good comparator which trips when the ADJ pin is at roughly 90% of its regulated value. The PGOOD output is an open-collector transistor that is off when the output is in regulation, allowing an external resistor to pull the PGOOD pin high. Power good is valid when the LTM8033 is enabled and VIN is above 3.6V. The LTM8033 is equipped with a thermal shutdown that will inhibit power switching at high junction temperatures. The activation threshold of this function, however, is above 125C to avoid interfering with normal operation. Thus, prolonged or repetitive operation under a condition in which the thermal shutdown activates may damage or impair the reliability of the device. 8033fb 10 For more information www.linear.com/LTM8033 LTM8033 APPLICATIONS INFORMATION For most applications, the design process is straight forward, summarized as follows: * Look at Table 1 and find the row that has the desired input range and output voltage. * Apply the recommended CIN, CFIN, COUT, RADJ and RT values. * Connect BIAS as indicated. As the integrated input EMI filter may ring in response to an application of a step input voltage, a bulk capacitance may be applied between FIN and GND. See the Hot-Plugging Safely section for details. While these component combinations have been tested for proper operation, it is incumbent upon the user to verify proper operation over the intended system's line, load and environmental conditions. Bear in mind that the maximum output current is limited by junction temperature, the relationship between the input and output voltage magnitude and polarity and other factors. Please refer to the graphs in the Typical Performance Characteristics section for guidance. The maximum frequency (and attendant RT value) at which the LTM8033 should be allowed to switch is given in Table 1 in the fMAX column, while the recommended frequency (and RT value) for optimal efficiency over the given input condition is given in the fOPTIMAL column. There are additional conditions that must be satisfied if the synchronization function is used. Please refer to the Synchronization section for details. Note: An input bulk capacitance is required at either VIN or FIN. Refer to the Typical Performance Characteristics section for load conditions. Capacitor Selection Considerations The CIN, CFIN and COUT capacitor values in Table 1 are the minimum recommended values for the associated operating conditions. Applying capacitor values below those indicated in Table 1 is not recommended, and may result in undesirable operation. Using larger values is generally acceptable, and can yield improved dynamic response, if it is necessary. Again, it is incumbent upon the user to verify proper operation over the intended system's line, load and environmental conditions. Ceramic capacitors are small, robust and have very low ESR. However, not all ceramic capacitors are suitable. X5R and X7R types are stable over temperature and applied voltage and give dependable service. Other types, including Y5V and Z5U have very large temperature and voltage coefficients of capacitance. In an application circuit they may have only a small fraction of their nominal capacitance resulting in much higher output voltage ripple than expected. Ceramic capacitors are also piezoelectric. In Burst Mode operation, the LTM8033's switching frequency depends on the load current, and can excite a ceramic capacitor at audio frequencies, generating audible noise. Since the LTM8033 operates at a lower current limit during Burst Mode operation, the noise is typically very quiet to a casual ear. If this audible noise is unacceptable, use a high performance electrolytic capacitor at the output. It may also be a parallel combination of a ceramic capacitor and a low cost electrolytic capacitor. A final precaution regarding ceramic capacitors concerns the maximum input voltage rating of the LTM8033. A ceramic input capacitor combined with trace or cable inductance forms a high Q (under damped) tank circuit. If the LTM8033 circuit is plugged into a live supply, the input voltage can ring to twice its nominal value, possibly exceeding the device's rating. This situation can be easily avoided; see the Hot-Plugging Safely section. 8033fb For more information www.linear.com/LTM8033 11 LTM8033 APPLICATIONS INFORMATION Table 1. Recommended Component Values and Configuration (TA = 25C) VIN VOUT CIN CFIN COUT BIAS RADJ fOPTIMAL RT(OPTIMAL) fMAX RT(MIN) 3.6V to 36V 0.8V 4.7F, 50V, 1206 10F, 50V, 1210 4 x 100F, 6.3V, 1210 2.8V to 25V 30M 230kHz 182k 250kHz 169k 3.6V to 36V 1V 4.7F, 50V, 1206 10F, 50V, 1210 4 x 100F, 6.3V, 1210 2.8V to 25V 1.87M 240kHz 174k 285kHz 147k 3.6V to 36V 1.2V 4.7F, 50V, 1206 10F, 50V, 1210 4 x 100F, 6.3V, 1210 2.8V to 25V 953k 255kHz 162k 315kHz 130k 3.6V to 36V 1.5V 4.7F, 50V, 1206 10F, 50V, 1210 4 x 100F, 6.3V, 1210 2.8V to 25V 549k 270kHz 154k 360kHz 113k 3.6V to 36V 1.8V 4.7F, 50V, 1206 10F, 50V, 1210 4 x 100F, 6.3V, 1210 2.8V to 25V 383k 285kHz 147k 420kHz 95.3k 4.1V to 36V 2.5V 4.7F, 50V, 1206 10F, 50V, 1210 3 x 100F, 6.3V, 1210 2.8V to 25V 226k 345kHz 118k 540kHz 71.5k 5.3V to 36V 3.3V 4.7F, 50V, 1206 10F, 50V, 1210 100F, 6.3V, 1210 AUX 154k 425kHz 93.1k 675kHz 54.9k 36.5k 7.5V to 36V 5V 4.7F, 50V, 1206 4.7F, 50V, 1206 100F, 6.3V, 1210 AUX 93.1k 500kHz 76.8k 950kHz 10.5V to 36V 8V 4.7F, 50V, 1206 1F, 50V, 1206 47F, 16V, 1210 AUX 54.9k 700kHz 52.3k 1.45MHz 20.5k 20V to 36V 12V 2.2F, 50V, 1206 1F, 50V, 1206 47F, 16V, 1210 AUX 34.8k 850kHz 41.2k 2.3MHz 9.09k 25.5V to 36V 18V 2.2F, 50V, 1206 Open 22F, 25V, 1812 AUX 22.6k 1.1MHz 29.4k 2.4MHz 8.25k 32.5V to 36V 24V 1F, 50V, 1206 Open 22F, 25V, 1812 2.8V to 20V 16.5k 1.2MHz 25.5k 2.4MHz 8.25k 3.6V to 15V 0.8V 4.7F, 25V, 1206 10F, 16V, 1210 4 x 100F, 6.3V, 1210 VIN 30M 230kHz 182k 575kHz 66.5k 3.6V to 15V 1V 4.7F, 25V, 1206 10F, 16V, 1210 4 x 100F, 6.3V, 1210 VIN 1.87M 240kHz 174k 660kHz 56.2k 3.6V to 15V 1.2V 4.7F, 25V, 1206 10F, 16V, 1210 4 x 100F, 6.3V, 1210 VIN 953k 255kHz 162k 760kHz 47.5k 3.6V to 15V 1.5V 4.7F, 25V, 1206 10F, 16V, 1210 4 x 100F, 6.3V, 1210 VIN 549k 270kHz 154k 840kHz 42.2k 3.6V to 15V 1.8V 4.7F, 25V, 1206 10F, 16V, 1210 4 x 100F, 6.3V, 1210 VIN 383k 285kHz 147k 1.0MHz 34.0k 4.1V to 15V 2.5V 4.7F, 16V, 1206 10F, 16V, 1210 3 x 100F, 6.3V, 1210 VIN 226k 345kHz 118k 1.3MHz 23.7k 5.3V to 15V 3.3V 4.7F, 16V, 1206 10F, 16V, 1210 100F, 6.3V, 1210 AUX 154k 425kHz 93.1k 1.6MHz 17.8k 7.5V to 15V 5V 4.7F, 16V, 1206 4.7F, 50V, 1206 100F, 6.3V, 1210 AUX 93.1k 500kHz 76.8k 2.4MHz 8.25k 10.5V to 15V 8V 2.2F, 25V, 1206 Open 47F, 16V, 1210 AUX 54.9k 700kHz 52.3k 2.4MHz 8.25k 30M 9V to 24V 0.8V 4.7F, 25V, 1206 4.7F, 25V, 1206 4 x 100F, 6.3V, 1210 VIN 270kHz 154k 360kHz 113k 9V to 24V 1V 4.7F, 25V, 1206 4.7F, 25V, 1206 4 x 100F, 6.3V, 1210 VIN 1.87M 285kHz 147k 410kHz 97.6k 9V to 24V 1.2V 4.7F, 25V, 1206 4.7F, 25V, 1206 4 x 100F, 6.3V, 1210 VIN 953k 295kHz 140k 475kHz 82.5k 9V to 24V 1.5V 4.7F, 25V, 1206 4.7F, 25V, 1206 4 x 100F, 6.3V, 1210 VIN 549k 310kHz 133k 550kHz 69.8k 9V to 24V 1.8V 4.7F, 25V, 1206 4.7F, 25V, 1206 3 x 100F, 6.3V, 1210 VIN 383k 330kHz 124k 620kHz 60.4k 9V to 24V 2.5V 4.7F, 25V, 1206 4.7F, 25V, 1206 2 x 100F, 6.3V, 1210 VIN 226k 345kHz 118k 800kHz 44.2k 9V to 24V 3.3V 4.7F, 25V, 1206 4.7F, 25V, 1206 100F, 6.3V, 1210 AUX 154k 425kHz 93.1k 1.0MHz 34.0k 9V to 24V 5V 4.7F, 25V, 1206 4.7F, 25V, 1206 100F, 6.3V, 1210 AUX 93.1k 500kHz 76.8k 1.4MHz 21.5k 10.5V to 24V 8V 2.2F, 25V, 1206 1F, 25V, 1206 47F, 16V, 1210 AUX 54.9k 700kHz 52.3k 2.2MHz 9.76k 20V to 24V 12V 2.2F, 25V, 1206 1F, 25V, 1206 47F, 16V, 1210 AUX 34.8k 850kHz 41.2k 2.3MHz 9.09k 30M 18V to 36V 0.8V 1F, 50V, 1206 2.2F, 50V, 1206 4 x 100F, 6.3V, 1210 2.8V to 25V 230kHz 182k 250kHz 169k 18V to 36V 1V 1F, 50V, 1206 2.2F, 50V, 1206 4 x 100F, 6.3V, 1210 2.8V to 25V 1.87M 240kHz 174k 285kHz 147k 18V to 36V 1.2V 1F, 50V, 1206 2.2F, 50V, 1206 4 x 100F, 6.3V, 1210 2.8V to 25V 953k 255kHz 162k 315kHz 130k 18V to 36V 1.5V 1F, 50V, 1206 2.2F, 50V, 1206 4 x 100F, 6.3V, 1210 2.8V to 25V 549k 270kHz 154k 360kHz 113k 18V to 36V 1.8V 1F, 50V, 1206 2.2F, 50V, 1206 3 x 100F, 6.3V, 1210 2.8V to 25V 383k 285kHz 147k 420kHz 95.3k 18V to 36V 2.5V 1F, 50V, 1206 2.2F, 50V, 1206 2 x 100F, 6.3V, 1210 2.8V to 25V 226k 345kHz 118k 540kHz 71.5k 18V to 36V 3.3V 1F, 50V, 1206 2.2F, 50V, 1206 100F, 6.3V, 1210 AUX 154k 425kHz 93.1k 675kHz 54.9k 18V to 36V 5V 1F, 50V, 1206 1F, 50V, 1206 47F, 10V, 1210 AUX 93.1k 500kHz 76.8k 950kHz 36.5k 18V to 36V 8V 2.2F, 50V, 1206 1F, 50V, 1206 47F, 16V, 1210 AUX 54.9k 700kHz 52.3k 1.45MHz 20.5k Note: A bulk capacitor is required. Do not allow VIN + BIAS above 56V. 8033fb 12 For more information www.linear.com/LTM8033 LTM8033 APPLICATIONS INFORMATION Frequency Selection BIAS Pin Considerations The LTM8033 uses a constant frequency PWM architecture that can be programmed to switch from 200kHz to 2.4MHz by using a resistor tied from the RT pin to ground. Table 2 provides a list of RT resistor values and their resulting frequencies. The BIAS pin is used to provide drive power for the internal power switching stage and operate other internal circuitry. For proper operation, it must be powered by at least 2.8V. If the output voltage is programmed to 2.8V or higher, BIAS may be simply tied to VOUT. If VOUT is less than 2.8V, BIAS can be tied to VIN or some other voltage source. If the BIAS pin voltage is too high, the efficiency of the LTM8033 may suffer. The optimum BIAS voltage is dependent upon many factors, such as load current, input voltage, output voltage and switching frequency, but 4V to 5V works well in many applications. In all cases, ensure that the maximum voltage at the BIAS pin is less than 25V and that the sum of VIN and BIAS is less than 56V. If BIAS power is applied from a remote or noisy voltage source, it may be necessary to apply a decoupling capacitor locally to the pin. Table 2. Switching Frequency vs RT Value SWITCHING FREQUENCY (MHz) RT VALUE (k) 0.2 215 0.3 137 0.4 100 0.5 76.8 0.6 63.4 0.7 52.3 0.8 44.2 0.9 38.3 1 34 1.2 25.5 1.4 21.5 1.6 17.8 1.8 14.7 2 12.1 2.2 9.76 2.4 8.25 Operating Frequency Trade-Offs It is recommended that the user apply the optimal RT value given in Table 1 for the input and output operating condition. System level or other considerations, however, may necessitate another operating frequency. While the LTM8033 is flexible enough to accommodate a wide range of operating frequencies, a haphazardly chosen one may result in undesirable operation under certain operating or fault conditions. A frequency that is too high can reduce efficiency, generate excessive heat or even damage the LTM8033 if the output is overloaded or short-circuited. A frequency that is too low can result in a final design that has too much output ripple or too large of an output capacitor. Load Sharing Two or more LTM8033 may be paralleled to produce higher currents. To do this, tie the VIN, ADJ, VOUT and SHARE pins of all the paralleled LTM8033 together. To ensure that paralleled modules start up together, the RUN/SS pins may be tied together as well. If the RUN/SS pins are not tied together, make sure that the same valued soft-start capacitors are used for each module. Current sharing can be improved by synchronizing the LTM8033s. An example of two LTM8033 configured for load sharing is given in the Typical Applications section. Burst Mode Operation To enhance efficiency at light loads, the LTM8033 automatically switches to Burst Mode operation which keeps the output capacitor charged to the proper voltage while minimizing the input quiescent current. During Burst Mode operation, the LTM8033 delivers single cycle bursts of current to the output capacitor followed by sleep periods where the output power is delivered to the load by the output capacitor. In addition, VIN and BIAS quiescent currents are reduced to typically 30A and 75A respectively during the sleep time. As the load current decreases towards a 8033fb For more information www.linear.com/LTM8033 13 LTM8033 APPLICATIONS INFORMATION no-load condition, the percentage of time that the LTM8033 operates in sleep mode increases and the average input current is greatly reduced, resulting in higher efficiency. Burst Mode operation is enabled by tying SYNC to GND. To disable Burst Mode operation, tie SYNC to a stable voltage above 0.7V. Do not leave the SYNC pin floating. Minimum Input Voltage The LTM8033 is a step-down converter, so a minimum amount of headroom is required to keep the output in regulation. In addition, the input voltage required to turn on is higher than that required to run, and depends upon BIAS power whether RUN/SS is used. If BIAS is available before VOUT ramps up, the minimum VIN voltage to start may be reduced. As shown in the Typical Performance Characteristics section, the minimum input voltage to run a 3.3V output at light load is only about 3.6V, but, if RUN/SS is pulled up to VIN, it takes 5.6VIN to start. If the LTM8033 is enabled with the RUN/SS pin, the minimum voltage to start at light loads is lower, about 4.2V. Similar curves detailing this behavior of the LTM8033 for other outputs are also included in the Typical Performance Characteristics section. RUN 15k RUN/SS 0.22F GND Soft-Start The RUN/SS pin can be used to soft-start the LTM8033, reducing the maximum input current during start-up. The RUN/SS pin is driven through an external RC filter to create a voltage ramp at this pin. Figure 2 shows the start-up and shutdown waveforms with the soft-start circuit. By choosing an appropriate RC time constant, the peak startup current can be reduced to the current that is required to regulate the output, with no overshoot. Choose the value of the resistor so that it can supply at least 20A when the RUN/SS pin reaches 2.5V. Frequency Foldback The LTM8033 is equipped with frequency foldback which acts to reduce the thermal and energy stress on the internal power elements during a short-circuit or output overload condition. If the LTM8033 detects that the output has fallen out of regulation, the switching frequency is reduced as a function of how far the output is below the target voltage. This in turn limits the amount of energy that can be delivered to the load under fault. During the start-up time, frequency foldback is also active to limit the energy delivered to the potentially large output capacitance of the load. INTERNAL INDUCTOR CURRENT 1A/DIV VRUN/SS 2V/DIV VOUT 2V/DIV 2ms/DIV 8033 F02 Figure 2. To Soft-Start the LTM8033, Add a Resistor and Capacitor to the RUN/SS Pin 8033fb 14 For more information www.linear.com/LTM8033 LTM8033 APPLICATIONS INFORMATION Synchronization Shorted Input Protection The internal oscillator of the LTM8033 can be synchronized by applying an external 250kHz to 2MHz clock to the SYNC pin. Do not leave this pin floating. Ground the SYNC pin if the synchronization function is not used. When synchronizing the LTM8033, select an RT resistor value that corresponds to an operating frequency 20% lower than the intended synchronization frequency (see the Frequency Selection section). Care needs to be taken in systems where the output will be held high when the input to the LTM8033 is absent. This may occur in battery charging applications or in battery backup systems where a battery or some other supply is diode OR-ed with the LTM8033's output. If the VIN pin is allowed to float and the RUN/SS pin is held high (either by a logic signal or because it is tied to VIN), then the LTM8033's internal circuitry will pull its quiescent current through its internal power switch. This is fine if your system can tolerate a few milliamps in this state. If you ground the RUN/SS pin, the SW pin current will drop to essentially zero. However, if the VIN pin is grounded while the output is held high, then parasitic diodes inside the LTM8033 can pull large currents from the output through the VIN pin. Figure 3 shows a circuit that will run only when the input voltage is present and that protects against a shorted or reversed input. In addition to synchronization, the SYNC pin controls Burst Mode behavior. If the SYNC pin is driven by an external clock, or pulled up above 0.7V, the LTM8033 will not enter Burst Mode operation, but will instead skip pulses to maintain regulation instead. VIN LTM8033 VIN RUN/SS VOUT VOUT AUX BIAS SHARE ADJ RT SYNC GND 8033 F03 Figure 3. The Input Diode Prevents a Shorted Input from Discharging a Backup Battery Tied to the Output. It Also Protects the Circuit from a Reversed Input. The LTM8033 Runs Only When the Input is Present 8033fb For more information www.linear.com/LTM8033 15 LTM8033 APPLICATIONS INFORMATION PCB Layout Most of the headaches associated with PCB layout have been alleviated or even eliminated by the high level of integration of the LTM8033. The LTM8033 is nevertheless a switching power supply, and care must be taken to minimize EMI and ensure proper operation. Even with the high level of integration, you may fail to achieve specified operation with a haphazard or poor layout. See Figure 4 for a suggested layout. Ensure that the grounding and heat sinking are acceptable. A few rules to keep in mind are: 1. Place the RADJ and RT resistors as close as possible to their respective pins. 2. Place the CIN and CFIN capacitors as close as possible to the VIN, FIN and GND connections of the LTM8033. A haphazardly placed CFIN capacitor may impair EMI performance. 3. Place the COUT capacitors as close as possible to the VOUT and GND connection of the LTM8033. 4. Place the CIN, CFIN and COUT capacitors such that their ground currents flow directly adjacent or underneath the LTM8033. 5. Connect all of the GND connections to as large a copper pour or plane area as possible on the top layer. Avoid breaking the ground connection between the external components and the LTM8033. 6. Use vias to connect the GND copper area to the board's internal ground planes. Liberally distribute these GND vias to provide both a good ground connection and thermal path to the internal planes of the printed circuit board. Pay attention to the location and density of the thermal vias in Figure 4. The LTM8033 can benefit from the heat sinking afforded by vias that connect to internal GND planes at these locations, due to their proximity to internal power handling components. The optimum number of thermal vias depends upon the printed circuit board design. For example, a board might use very small via holes. It should employ more thermal vias than a board that uses larger holes. PG SYNC GND FIN RUN/SS RADJ CFIN RT SHARE GND BIAS LTM8033 AUX COUT VOUT CIN GND VIN THERMAL VIAS TO GND Figure 4. Layout Showing Suggested External Components, GND Plane and Thermal Vias 8033fb 16 For more information www.linear.com/LTM8033 LTM8033 APPLICATIONS INFORMATION Hot-Plugging Safely The small size, robustness and low impedance of ceramic capacitors make them an attractive option for the input bypass capacitor of LTM8033. However, these capacitors can cause problems if the LTM8033 is plugged into a live supply (see Application Note 88 for a complete discussion). The low loss ceramic capacitor combined with stray inductance in series with the power source forms an underdamped tank circuit, and the voltage at the VIN pin of the LTM8033 can ring to more than twice the nominal input voltage, possibly exceeding the LTM8033's rating and damaging the part. A similar phenomenon can occur inside the LTM8033 module, at the output of the integrated EMI filter (FIN), with the same potential of damaging the part. If the input supply is poorly controlled or the user will be plugging the LTM8033 into an energized supply, the input network should be designed to prevent this overshoot. This can be accomplished by installing a small resistor in series to VIN, but the most popular method of controlling input voltage overshoot is adding an electrolytic bulk capacitor to the VIN or FIN net. This capacitor's relatively high equivalent series resistance damps the circuit and eliminates the voltage overshoot. The extra capacitor improves low frequency ripple filtering and can slightly improve the efficiency of the circuit, though it can be a large component in the circuit. Electromagnetic Compliance The LTM8033 was evaluated by an independent nationally recognized test lab and found to be compliant with EN 55022 class B: 2006 by a wide margin. Sample graphs of the LTM8033's radiated EMC performance are given in the Typical Performance Characteristics section, while further data, operating conditions and test set-up are detailed in the electromagnetic compatibility test report, available on the Linear Technology website. Conducted emissions requirements may be met by adding an appropriate input power line filter. The proper implementation of this filter depends upon the system operating and performance conditions as a whole, of which the LTM8033 is typically only a component, so conducted emissions are not addressed at this level. Thermal Considerations The LTM8033 output current may need to be derated if it is required to operate in a high ambient temperature or deliver a large amount of continuous power. The amount of current derating is dependent upon the input voltage, output power and ambient temperature. The temperature rise curves given in the Typical Performance Characteristics section can be used as a guide. These curves were generated by an LTM8033 mounted to a 40cm2 4-layer FR4 printed circuit board. Boards of other sizes and layer count can exhibit different thermal behavior, so it is incumbent upon the user to verify proper operation over the intended system's line, load and environmental operating conditions. The thermal resistance numbers listed in the Pin Configuration are based on modeling the Module package mounted on a test board specified per JESD51-9 "Test Boards for Area Array Surface Mount Package Thermal Measurements." The thermal coefficients provided in this page are based on JESD 51-12 "Guidelines for Reporting and Using Electronic Package Thermal Information." For increased accuracy and fidelity to the actual application, many designers use FEA to predict thermal performance. To that end, the Pin Configuration typically gives four thermal coefficients: * JA - Thermal resistance from junction to ambient. * JCBOTTOM - Thermal resistance from junction to the bottom of the product case. * JCTOP - Thermal resistance from junction to top of the product case. * JB - Thermal resistance from junction to the printed circuit board. 8033fb For more information www.linear.com/LTM8033 17 LTM8033 APPLICATIONS INFORMATION While the meaning of each of these coefficients may seem to be intuitive, JEDEC has defined each to avoid confusion and inconsistency. These definitions are given in JESD 51-12, and are quoted or paraphrased in the following: * JA is the natural convection junction-to-ambient air thermal resistance measured in a one cubic foot sealed enclosure. This environment is sometimes referred to as "still air" although natural convection causes the air to move. This value is determined with the part mounted to a JESD 51-9 defined test board, which does not reflect an actual application or viable operating condition. * JCBOTTOM is the junction-to-board thermal resistance with all of the component power dissipation flowing through the bottom of the package. In the typical Module, the bulk of the heat flows out the bottom of the package, but there is always heat flow out into the ambient environment. As a result, this thermal resistance value may be useful for comparing packages but the test conditions don't generally match the user's application. * JCTOP is determined with nearly all of the component power dissipation flowing through the top of the package. As the electrical connections of the typical Module are on the bottom of the package, it is rare for an application to operate such that most of the heat flows from the junction to the top of the part. As in the case of JCBOTTOM, this value may be useful for comparing packages but the test conditions don't generally match the user's application. * JB is the junction-to-board thermal resistance where almost all of the heat flows through the bottom of the Module and into the board, and is really the sum of the JCBOTTOM and the thermal resistance of the bottom of the part through the solder joints and through a portion of the board. The board temperature is measured a specified distance from the package, using a two sided, two layer board. This board is described in JESD 51-9. The most appropriate way to use the coefficients is when running a detailed thermal analysis, such as FEA, which considers all of the thermal resistances simultaneously. None of them can be individually used to accurately predict the thermal performance of the product, so it would be inappropriate to attempt to use any one coefficient to correlate to the junction temperature versus load graphs given in the LTM8033 data sheet. A graphical representation of these thermal resistances is given in Figure 5. The blue resistances are contained within the Module, and the green are outside. The die temperature of the LTM8033 must be lower than the maximum rating of 125C, so care should be taken in the layout of the circuit to ensure good heat sinking of the LTM8033. The bulk of the heat flow out of the LTM8033 is through the bottom of the module and the LGA pads into the printed circuit board. Consequently a poor printed circuit board design can cause excessive heating, resulting in impaired performance or reliability. Please JUNCTION-TO-AMBIENT RESISTANCE (JESD 51-9 DEFINED BOARD) JUNCTION-TO-CASE (TOP) RESISTANCE JUNCTION CASE (TOP)-TO-AMBIENT RESISTANCE JUNCTION-TO-BOARD RESISTANCE JUNCTION-TO-CASE CASE (BOTTOM)-TO-BOARD (BOTTOM) RESISTANCE RESISTANCE At BOARD-TO-AMBIENT RESISTANCE 8033 F05 MODULE REGULATOR Figure 5 8033fb 18 For more information www.linear.com/LTM8033 LTM8033 APPLICATIONS INFORMATION refer to the PCB Layout section for printed circuit board design suggestions. The LTM8033 is equipped with a thermal shutdown that will inhibit power switching at high junction temperatures. The activation threshold of this function, however, is above 125C to avoid interfering with normal operation. Thus, it follows that prolonged or repetitive operation under a condition in which the thermal shutdown activates necessarily means that the internal components are subjected to temperatures above the 125C rating for prolonged or repetitive intervals, which may damage or impair the reliability of the device. Finally, be aware that at high ambient temperatures the internal Schottky diode will have significant leakage current (see the Typical Performance Characteristics section) increasing the quiescent current of the LTM8033. TYPICAL APPLICATIONS 0.8V Step-Down Converter VIN 3.6V TO 15V LTM8033 VIN 4.7F BIAS VOUT 0.8V 400F 3A VOUT AUX RUN/SS PGOOD FIN 10F SHARE RT SYNC GND ADJ 182k 8033 TA02 30M f = 230kHz 1.8V Step-Down Converter VIN 3.6V TO 36V VIN 4.7F 2.8V TO 25V LTM8033 BIAS VOUT 1.8V 400F 3A VOUT AUX RUN/SS FIN 10F PGOOD SHARE RT SYNC GND ADJ 147k 8033 TA03 383k f = 285kHz NOTE: DO NOT ALLOW VIN + BIAS TO BE GREATER THAN 56V. 8033fb For more information www.linear.com/LTM8033 19 LTM8033 TYPICAL APPLICATIONS 2.5V Step-Down Converter VIN* 4.1V TO 36V VIN 4.7F LTM8033 SHARE 2.8V to 25V VOUT 2.5V 300F 3A VOUT AUX BIAS RUN/SS PGOOD FIN 10F RT SYNC GND ADJ 118k 8033 TA04 226k f = 345kHz NOTE: DO NOT ALLOW VIN + BIAS TO BE GREATER THAN 56V. * RUNNING VOLTAGE RANGE. PLEASE REFER TO THE APPLICATIONS INFORMATION SECTION FOR START-UP DETAILS. 5V Step-Down Converter VIN 7.5V TO 36VDC VIN LTM8033 SHARE AUX RUN/SS BIAS FIN VOUT 5V 100F 3A VOUT PGOOD 4.7F RT SYNC GND ADJ 4.7F 76.8k 8033 TA05 93.1k f = 500kHz 8V Step-Down Converter LTM8033 VIN* 11V TO 36V VIN 4.7F SHARE AUX RUN/SS BIAS FIN VOUT 8V 3A VOUT PGOOD 47F 1F RT SYNC GND ADJ 52.3k 54.9k f = 700kHz 8033 TA06 * RUNNING VOLTAGE RANGE. PLEASE REFER TO THE APPLICATIONS INFORMATION SECTION FOR START-UP DETAILS. 8033fb 20 For more information www.linear.com/LTM8033 LTM8033 TYPICAL APPLICATIONS Current Sharing Two LTM8033 Parts VIN* 4.8V TO 36V VIN 10F LTM8033 FIN AUX RUN/SS BIAS SHARE VOUT 2.5V 5.8A VOUT PGOOD 4.7F RT SYNC GND ADJ 137k 113k 2.8V to 25V OPTIONAL SYNCHRONIZATION CLOCK VIN VOUT FIN AUX RUN/SS BIAS SHARE 4.7F LTM8033 PGOOD 300F 10F RT SYNC GND ADJ 137k 8033 TA07 * RUNNING VOLTAGE RANGE. PLEASE REFER TO THE APPLICATIONS INFORMATION SECTION FOR START-UP DETAILS. NOTE: SYNCHRONIZE THE TWO MODULES TO AVOID BEAT FREQUENCIES, IF NECESSARY. OTHERWISE, TIE EACH SYNC TO GND. 8033fb For more information www.linear.com/LTM8033 21 LTM8033 PACKAGE DESCRIPTION Pin Assignment Table (Arranged by Pin Number) PIN NAME PIN NAME PIN NAME PIN NAME PIN NAME PIN NAME A1 VOUT B1 VOUT C1 VOUT D1 VOUT E1 GND F1 GND A2 VOUT B2 VOUT C2 VOUT D2 VOUT E2 GND F2 GND A3 VOUT B3 VOUT C3 VOUT D3 VOUT E3 GND F3 GND A4 GND B4 GND C4 GND D4 GND E4 GND F4 GND A5 GND B5 GND C5 GND D5 GND E5 GND F5 GND A6 SHARE B6 RT C6 GND D6 GND E6 GND F6 GND A7 ADJ B7 PGOOD C7 GND D7 GND E7 GND F7 GND A8 GND B8 SYNC C8 GND D8 GND E8 GND F8 GND PIN NAME PIN NAME PIN NAME PIN NAME PIN NAME G1 GND J1 VIN K1 VIN L1 VIN G2 GND J2 VIN K2 VIN L2 VIN G3 AUX J3 VIN K3 VIN L3 VIN G4 BIAS G5 GND H5 GND J5 GND K5 GND L5 GND G6 GND H6 GND J6 GND K6 GND L6 GND G7 GND G8 RUN J8 FIN K8 FIN L8 FIN PACKAGE PHOTOGRAPHS 8033fb 22 For more information www.linear.com/LTM8033 4 3.175 1.905 aaa Z Y X DETAIL C 15.00 BSC aaa Z 3.95 - 4.05 DETAIL A 0.635 0.025 75SQ 0.270 - 0.370 SUBSTRATE eee S X Y DETAIL B MOLD CAP DETAIL C 0.635 0.025 75SQ DETAIL B 4.22 - 4.42 (Reference LTC DWG # 05-08-1560 Rev A) eee S X Y For more information www.linear.com/LTM8033 1.270 6.350 5.080 3.810 2.540 1.270 7 PACKAGE ROW AND COLUMN LABELING MAY VARY AMONG Module PRODUCTS. REVIEW EACH PACKAGE LAYOUT CAREFULLY SYMBOL TOLERANCE aaa 0.15 bbb 0.10 eee 0.05 ! 6. THE TOTAL NUMBER OF PADS: 76 5. PRIMARY DATUM -Z- IS SEATING PLANE DETAILS OF PAD #1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED WITHIN THE ZONE INDICATED. THE PAD #1 IDENTIFIER MAY BE EITHER A MOLD OR MARKED FEATURE 4 0.000 LAND DESIGNATION PER JESD MO-222 3 2.540 2. ALL DIMENSIONS ARE IN MILLIMETERS 4.445 3.810 3.175 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994 SUGGESTED PCB LAYOUT TOP VIEW 0.635 Z 5.080 6.350 0.635 PACKAGE TOP VIEW 11.25 BSC 1.905 bbb Z PAD "A1" CORNER 4.445 LGA Package 76-Lead (15mm x 11.25mm x 4.32mm) TRAY PIN 1 BEVEL COMPONENT PIN "A1" 12.70 BSC 8 DETAIL A 7 8.89 BSC 5 4 3 1.27 BSC 2 1 L K J H G F E D C B A 7 LGA 76 1212 REV A 3 PADS SEE NOTES PAD 1 PACKAGE IN TRAY LOADING ORIENTATION LTMXXXXXX Module PACKAGE BOTTOM VIEW 6 SEE NOTES LTM8033 PACKAGE DESCRIPTION Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. 8033fb 23 3.175 SUGGESTED PCB LAYOUT TOP VIEW 1.905 aaa Z 0.630 0.025 O 76x E 0.000 PACKAGE TOP VIEW 0.635 4 0.635 PIN "A1" CORNER 1.905 Y X D For more information www.linear.com/LTM8033 6.350 5.080 3.810 2.540 1.270 0.000 1.270 2.540 3.810 5.080 6.350 aaa Z SYMBOL A A1 A2 b b1 D E e F G H1 H2 aaa bbb ccc ddd eee H1 SUBSTRATE NOM 4.92 0.60 4.32 0.75 0.63 15.00 11.25 1.27 12.70 8.89 0.32 4.00 MAX 5.12 0.70 4.42 0.90 0.66 NOTES DETAIL B PACKAGE SIDE VIEW 0.37 4.05 0.15 0.10 0.20 0.30 0.15 TOTAL NUMBER OF BALLS: 76 0.27 3.95 MIN 4.72 0.50 4.22 0.60 0.60 b1 DIMENSIONS ddd M Z X Y eee M Z DETAIL A Ob (76 PLACES) DETAIL B H2 MOLD CAP ccc Z A1 A2 A Z (Reference LTC DWG # 05-08-1952 Rev O) // bbb Z 24 Z BGA Package 76-Lead (15mm x 11.25mm x 4.92mm) e b 7 5 G 4 e 3 PACKAGE BOTTOM VIEW 6 2 1 L K J H G F E D C B A DETAILS OF PIN #1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED WITHIN THE ZONE INDICATED. THE PIN #1 IDENTIFIER MAY BE EITHER A MOLD OR MARKED FEATURE 4 3 TRAY PIN 1 BEVEL COMPONENT PIN "A1" 7 ! PACKAGE IN TRAY LOADING ORIENTATION LTMXXXXXX Module BGA 76 0513 REV O PACKAGE ROW AND COLUMN LABELING MAY VARY AMONG Module PRODUCTS. REVIEW EACH PACKAGE LAYOUT CAREFULLY 6. SOLDER BALL COMPOSITION IS 96.5% Sn/3.0% Ag/0.5% Cu 5. PRIMARY DATUM -Z- IS SEATING PLANE BALL DESIGNATION PER JESD MS-028 AND JEP95 3 2. ALL DIMENSIONS ARE IN MILLIMETERS 7 SEE NOTES PIN 1 SEE NOTES NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994 F b 8 DETAIL A LTM8033 PACKAGE DESCRIPTION Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. 8033fb 3.175 4.445 4.445 LTM8033 REVISION HISTORY REV DATE DESCRIPTION PAGE NUMBER A 04/14 Add BGA package option B 09/14 1, 2, 22, 24 BGA ball A1 was missing, corrected 2 Changed quiescent current VIN and BIAS from 20A and 50A to 30A and 75A, respectively 13 8033fb Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. For more information www.linear.com/LTM8033 25 LTM8033 TYPICAL APPLICATION 3.3V Step-Down Converter VIN 5.5V TO 36VDC VIN LTM8033 SHARE AUX RUN/SS BIAS FIN VOUT 3.3V 100F 3A VOUT PGOOD 4.7F 10F RT SYNC GND ADJ 93.1k 8033 TA08 154k f = 425kHz RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTM8031 Ultralow Noise EMC 1A Module Regulator EN55022 Class B Compliant, 3.6V VIN 36V; 0.8V VOUT 10V, 9mm x 15mm x 2.82mm LGA LTM8032 Ultralow Noise EMC 2A Module Regulator EN55022 Class B Compliant, 3.6V VIN 36V; 0.8V VOUT 10V 9mm x 15mm x 2.82mm LGA and 9mm x 15mm x 3.42mm BGA LTM4613 36VIN, 8A EN55022 Class B Certified DC/DC Step-Down Module Regulator 5V VIN 36V, 3.3V VOUT 15V, PLL Input, VOUT Tracking and Margining, 15mm x 15mm x 4.32mm LGA LTM4612 36VIN, 5A EN55022 Class B Certified DC/DC Step-Down Module Regulator 5V VIN 36V, 3.3V VOUT 15V, PLL Input, VOUT Tracking and Margining, 15mm x 15mm x 2.82mm LGA LTM4624 14VIN, 4A Step-Down Module Regulator in tiny 6.25mm x 6.25mm x 5.01mm BGA 4V VIN 14V, 0.6V VOUT 5.5V, VOUT Tracking, PGOOD, Light Load Mode, Complete Solution in 1cm2 (Single-Sided PCB) 8033fb 26 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 For more information www.linear.com/LTM8033 (408) 432-1900 FAX: (408) 434-0507 www.linear.com/LTM8033 LT 0914 REV B * PRINTED IN USA (c) LINEAR TECHNOLOGY CORPORATION 2010