APL111712FC-L - Anpec Electronics Corp.

Rev. C.6 - Mar., 2008

APL1117

www.anpec.com.tw1

ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise

customers to obtain the latest version of relevant information to verify before placing orders.

1A Low Dropout Fast Response Positive Adjustable Regulator and

Fixed 1.2V,1.8V, 2.5V, 2.85V, 3.3V and 5V

General Description

The APL1117 is a low dropout three-terminal adjustable

regulators with 1A output current capability. In order

to obtain lower dropout voltage and faster transient

response, which is critical for low voltage applications,

the APL1117 has been optimized. The device is

available in an adjustable version and fixed output

voltages of 1.2V, 1.8V, 2.5V, 2.85V, 3.3V and 5V.

The output available voltage range of an adjustable ver-

sion is from 1.25~10.7V with an input supply below

12V. Dropout voltage is guaranteed at a maximum of

1.3V at 1A. Current limit is trimmed to ensure speci-

fied output current and controlled short-circuit

current. On-chip thermal limiting provides protection

against any combination of overload that would

create excessive junction temperatures. The

APL1117 is available in the industry standard 3-pin TO-

220, TO-252, TO-263, and the low profile surface

mount SOT-223 power packages which can be used

in applications where space is limited.

•Guaranteed Output Voltage Accuracy within 2%

•Fast Transient Response

•Guaranteed Dropout Voltage at Multiple

Currents

•Load Regulation : 0.1% Typ.

•Line Regulation : 0.03% Typ.

•Low Dropout Voltage : 1.1V Typ. at IOUT =1A

•Current Limit : 1A Typ. at TJ=25°C

•On-Chip Thermal Limiting : 150°C Typ.

•Adjustable Output : 1.25~10.7V

•Standard 3-pin TO-220, TO-252, TO-263 and

SOT-223 Power Packages

•Lead Free Available (RoHS Compliant)

Features

Applications

Pin Description

Front View for TO-263Front View for TO-220

•Active SCSI Terminators

•Low Voltage Logic Supplies

•Post Regulator for Switching Power Supply

Front View for SOT-223

Front View for TO-252

3VIN

VOUT

ADJ/GND

TAB is VOUT

3VIN

VOUT

ADJ/GND

TAB IS VOUT 1

3VIN

VOUT

ADJ/GND

TAB IS VOUT VOUT

ADJ/GND

VIN

Rev. C.6 - Mar., 2008

APL1117

www.anpec.com.tw2

Ordering and Marking Information

Symbol Parameter Rating(Note) Unit

VIN Input Voltage APL1117, APL1117-33

APL1117-50

APL1117-12, APL1117-18, APL1117-25, APL1117-28

9 V

TJ Operating Junction Temperature Range 0 to 150 °C

TSTG Storage Temperature Range -65 to +150 °C

TSDR Maximum Lead Soldering Temperature,

10 second

260 °C

Absolute Maximum Ratings

Note : The values here show the absolute maximum rating, and for normal usage please refer the test condition in

Electrical Characteristics Table.

Note: ANPEC lead-free products contain molding compounds/die attach materials and 100% matte tin plate termination finish; which

are fully compliant with RoHS. ANPEC lead-free products meet or exceed the lead-free requirements of IPC/JEDEC J-STD-020C for

MSL classification at lead-free peak reflow temperature. ANPEC defines “Green” to mean lead-free (RoHS compliant) and halogen

free (Br or Cl does not exceed 900ppm by weight in homogeneous material and total of Br and Cl does not exceed 1500ppm by

weight).

Package Code

F : TO-220 G : TO-263 U : TO-252 V : SOT-223

Temp. Range

C : 0 to 70 C

Handling Code

TR : Tape & Reel

Voltage Code

12: 1.2V 18 : 1.8V 25 : 2.5V 28 : 2.85V

33 : 3.3V 50 : 5V Blank : Adjustable Version

Assembly Material

L : Lead Free Device G : Halogen and Lead Free Device

APL1117

Handling Code

Temp. Range

Package Code

Voltage Code

APL1117

XXXXX25 XXXXX - Date Code

APL1117-25V :

APL1117

XXXXX33 XXXXX - Date CodeAPL1117-33V :

APL1117 -33F/G/U : APL1117

XXXXX

APL1117-25F/G/U : APL1117

XXXXX

APL1117-18F/G/U : APL1117

XXXXX

18 APL1117

XXXXX18 XXXXX - Date Code

APL1117-18V :

APL1117

XXXXX28 XXXXX - Date Code

APL1117-28V :

APL1117-28F/G/U : APL1117

XXXXX

APL1117 F/G/U : APL1117

XXXXX XXXXX - Date Code APL1117

XXXXX XXXXX - Date Code

APL1117 V :

Assembly Material

XXXXX - Date Code

APL1117

XXXXX50 XXXXX - Date CodeAPL1117-50V :

APL1117 -50F/G/U : APL1117

XXXXX

50 XXXXX - Date Code

APL1117-12F/G/U : APL1117

XXXXX

12 APL1117

XXXXX12 XXXXX - Date Code

APL1117-12V :

XXXXX - Date Code

Rev. C.6 - Mar., 2008

APL1117

www.anpec.com.tw3

Electrical Characteristics

APL1117

Symbol

Parameter Test Conditions Min.

Typ.

Max.

Unit

VREF Reference Voltage 10mA≤ IOUT ≤1A, 1.4V≤(VIN -VOUT) ≤

10.75V,

0~125

1.225

1.250

1.275

VOUT Output Voltage

APL1117-12

TJ = 0~125°C,

0≤ IOUT ≤ 1A, 2.65V≤ VIN ≤9V,

1.176

1.200

1.224

APL1117-18

TJ = 0~125°C,

≤

OUT

≤

1A, 3.

≤

9V,

1.764

1.800

1.836

APL1117-25

TJ = 0~125°C,

≤

OUT

≤

1A,

3.95

≤

9V,

2.450

2.500

2.550

APL1117-28

TJ = 0~125°C,

≤

OUT

≤

1A, 4.25V

≤

9V,

2.790

2.850

2.910

APL1117-33

TJ = 0~125°C,

≤

OUT

≤

1A, 4.75V

≤

12V,

3.235

3.300

3.365

APL1117-50

TJ = 0~125°C,

0≤ IOUT ≤ 1A, 6.45V≤ VIN ≤12V, 4.900

5.000

5.100

REGLINE

Line Regulation

APL1117

IOUT =10mA, 1.5V≤(VIN -VOUT)≤10.75V (Note1)

0.03

0.2

APL1117-12

IOUT = 0A, 2.65V≤ VIN ≤9V (Note1) 1 6

APL1117-18

IOUT = 0A, 3.25V≤ VIN ≤9V (Note1) 1 6

APL1117-25

IOUT = 0A, 3.95V≤ VIN ≤9V (Note1) 1 6

APL1117-28

IOUT = 0A, 4.25V≤ VIN ≤9V (Note1) 1 6

APL1117-33

IOUT = 0A, 4.75V≤ VIN ≤12V (Note1) 1 6

APL1117-50

IOUT = 0A, 6.45V≤ VIN ≤12V (Note1) 1 6

REGLOAD

Load Regulation

APL1117

(VIN -VOUT)=3V, 0≤ IOUT ≤1A (Note1)

0.1

0.4

APL1117-12

VIN = 2.65V, 0≤ IOUT ≤1A (Note1) 1 10

APL1117-18

VIN = 3.25V, 0≤ IOUT ≤1A (Note1) 1 10

APL1117-25

VIN = 3.95V, 0≤ IOUT ≤1A (Note1) 1 10

APL1117-28

VIN = 4.25V, 0≤ IOUT ≤1A (Note1) 1 10

APL1117-33

VIN = 4.75V, 0≤ IOUT ≤1A (Note1) 1 10

APL1117-50

VIN = 6.45V, 0≤ IOUT ≤1A (Note1) 1 10

IOUT = 100mA (Note2) 1 1.1

VD Dropout Voltage IOUT = 500mA (Note2)

IOUT = 1A (Note2) 1.05

1.1 1.2

1.3

ILIMIT Current Limit (VIN -VOUT) = 5V, TJ = 25°C 1000

IADJ Adjust Pin Current

APL1117 (VIN -VOUT) = 3V, IOUT = 10mA 60 120

µA

∆IADJ Adjust Pin Current

Change APL1117 10mA≤ IOUT ≤1A,

1.4V

≤

OUT

)

≤

10.75V

0.2 5 µA

IO Minimum Load

Current APL1117 (VIN -VOUT) = 10.75V (Note3) 1.7 mA

Unless otherwise noted , these specifications apply over CIN = 10µF , COUT = 10µF , and TA = 0 to 70°C. Typical values

refer to TA = 25°C.

Rev. C.6 - Mar., 2008

APL1117

www.anpec.com.tw4

Electrical Characteristics (Cont.)

APL1117

Symbol

Parameter Test Conditions Min.

Typ.

Max.

Unit

PSRR

Ripple Rejection fRIPPLE =120Hz, VRIPPLE = 1VP-P,

(VIN -VOUT) = 3V 60 75 dB

TR Thermal Regulation TJ = 25°C, 30ms Pulse 0.01

0.02

%/ W

TS Temperature Stability 0.5 %

LS Long -Term Stability TJ = 125°C, 1000Hrs. 0.3 %

VN RMS Output Noise TJ = 25°C, 10Hz≤F≤10kHz,

(% of VOUT) 0.003

IOUT=100mA (Note2) 1 1.1

VD Dropout Voltage IOUT=500mA (Note2)

IOUT=1A (Note2) 1.05

1.1 1.2

1.3 V

ILIMIT Current Limit (VIN -VOUT)=5V, TJ=25°

1000

IADJ Adjust Pin Current

APL1117 (VIN -VOUT)=3V, IOUT=10mA 60 120

µA

∆IADJ Adjust Pin

Current

Change APL1117 10mA≤ IOUT ≤1A,

1.4V≤(VIN -VOUT) ≤10.75V 0.2 5 µA

IO Minimum Load Current

APL1117 (VIN -VOUT)=10.75V (Note3) 1.7 mA

PSRR

Ripple Rejection fRIPPLE=120Hz, VRIPPLE=1VP-P,

(VIN -VOUT)=3V 60 75 dB

TR Thermal Regulation TJ=25°C, 30ms Pulse 0.01

0.02

%/W

TS Temperature Stability 0.5 %

LS Long -Term Stability TJ =125°C,1000Hrs. 0.3 %

VN RMS Output Noise TJ=25°C,10Hz≤F≤10kHz, (% of VOUT)

0.003

θJC Thermal Resistance

Junction to Case

SOT-223

TO-252

TO-263

TO-220

°C/ W

OT Over Temperature Point

150 °C

IQ Quiescent Current

APL1117-12,18,25,28

APL1117-33,50

VIN≤9V

VIN≤12V

5.5

10 mA

Note 1 : See thermal regulation specifications for changes in output voltage due to heating effects. Load line

regulations are measured at a constant junction temperature by low duty cycle pulse testing.

Note 2 : Dropout voltage is specified over the full output current range of the device. Dropout voltage is defined as the

minimum input/output differential measured at the specified output current. Test points and limits are also

shown on the Dropout Voltage curve.

Note 3 : Minimum load current is defined as the minimum output current required to maintain regulation.

Unless otherwise noted , these specifications apply over CIN = 10µF , COUT = 10µF , and TA = 0 to 70°C. Typical values

refer to TA = 25°C.

Rev. C.6 - Mar., 2008

APL1117

www.anpec.com.tw5

Block Diagram

Application Circuits

* C1 improves ripple rejection.

should be approximately

equal to R1 at ripple frequency

* Needed if device is far from filter capacitors

1.25V to 10.7V Adjustable RegulatorImproving Ripple Rejection

5V Regulator with Shutdown

VOUT = 1.250V XR1 + R2

VIN

10µ F

C1*

APL1117

OUTIN ADJ

+100µ F

121Ω

VIN

10µF121Ω

365Ω

VOUT

150µF

10µF

R2 +

APL1117

OUT

ADJ

VOUT1

Current Limit

Voltage

Regulation

Thermal

Protection

VIN VOUT

ADJ/GND

Rev. C.6 - Mar., 2008

APL1117

www.anpec.com.tw6

0 1 2 3 4 5 6 7 8 9

APL1117-33

-20 30 80 130 180-0.05

0.05

0.1

0.15

0.5

1.5

2.5

3.5

4.5

-100 100 300 500 700 900-0.03

-0.02

-0.01

0.01

0.02

0.9

0.95

1.05

1.1

1.15

1.2

1.25

00.2 0.4 0.6 0.8 1

Typical Characteristics

Input Voltage (V)

Time (µS)

Dropout Voltage vs. Output Current

Output Current (A)

Dropout Voltage (V)

Load Transietn Response

Output Current (A)

Time (µS)

Line Transient Response

CIN=10µF

COUT=10µF Tantalum

VIN=5V

CIN=10µF

COUT=10µF Tantalum

IOUT=0.1A

APL1117-33 APL1117-33

Output Voltage (V)

Output Voltage vs. Input Voltage

Input Voltage (V)

Rev. C.6 - Mar., 2008

APL1117

www.anpec.com.tw7

1.1

1.15

1.2

1.25

1.3

1.35

-50 -25 025 50 75 100 125

1.6

1.7

1.8

1.9

2.1

2.2

2.3

2.4

2.5

2.6

-50 -25 025 50 75 100 125

APL1117-33APL1117-33

1.2

1.4

1.6

1.8

2.2

2.4

5 7 9 11 13

0 2 4 6 8 10 12

Typical Characteristics Cont.

Current Limit (A)

Input Voltage (V)

Input Current vs. Input Voltage

Input Current (mA)

Input Voltage (V)

Current Limit vs. Input Voltage

Output Voltage vs. Temperature

Temperature (°C)

Output Voltage (V)

Output Voltage vs. Temperature

Temperature (°C)

Output Voltage (V)

Rev. C.6 - Mar., 2008

APL1117

www.anpec.com.tw8

4.7

4.8

4.9

5.1

5.2

5.3

-50 -25 025 50 75 100 125

1.1

1.2

1.3

1.4

1.5

1.6

1.7

1.8

1.9

-50 050 100 150

Typical Characteristics Cont.

Input Current (mA)

Temperature (°C)

Current Limit vs. Temperature

Temperature (°C)

Current Limit (A)

Output Voltage vs. Temperature

Output Voltage (V)

Temperature (°C)

Input Current vs. Tmeperature

VIN-VOUT=5V

APL1117-33 APL1117-33

2.7

2.8

2.9

3.1

3.2

3.3

3.4

-50 -25 025 50 75 100 125

Output Voltage (V)

Output Voltage vs. Temperature

Temperature (°C)

Rev. C.6 - Mar., 2008

APL1117

www.anpec.com.tw9

-50 -25 025 50 75 100 125

Typical Characteristics Cont.

Adjustable Pin Current vs. Temperature

Adjustable Pin Current (µA)

Temperature (°C)

APL1117-Adj

Output Voltage

The APL1117 develops a 1.25V reference voltage

between the output and the adjust terminal. By placing

a resistor between these two terminals, a constant

Current is caused to flow through R1 and down through

R2 to set the overall output voltage. Normally this

current is chosen to be the specified minimum load

current of 10mA. For fixed voltage devices R1 and R2

are included in the device.

Application Information

VIN

APL1117

OUTIN ADJ VREF R1

VOUT

IADJ

60µA

VOUT = V REF(1+ )+IADJR2

Figure 1. Basic Adjustable Regulator

Load Regulation

When the adjustable regulator is used. Load regulation

will be limited by the resistance of the wire connecting

the regulator to the load. The data sheet specification

for load regulation is measured at the output pin of the

device. Best load regulation is obtained when the top

of the resistor divider (R1) is tied directly to the output

pin of the device, not to the load. For fixed voltage

devices the top of R1 is internally connected to the

output, and the ground pin can be connected to low

side of the load. If R1 were connected to the load, RP

is multiplied by the divider ratio, the effective resistance

between the regulator and the load would be:

Rp X (1+ ), Rp = Parasitic Line Resistance

APL1117-33

-100

-90

-80

-70

-60

-50

-40

-30

-20

-10

200k

100

200

500

10k

20k

50k

PSRR (dB)

PSRR vs. Frequency

Frequency (Hz)

Cadj=22µF

IOUT=0.1A

Vripple=1Vp-p

VIN-VOUT>=Vdropout

VIN-VOUT>=3V

Rev. C.6 - Mar., 2008

APL1117

www.anpec.com.tw10

Input Capacitor

An input capacitor of 10µF or greater is recommended.

Tantalum, or aluminum electrolytic capacitors can be

used for bypassing. Larger Values will improve ripple

rejection by bypassing the input to the regulator.

Output Capacitor

The APL1117 requires an output capacitor to maintain

stability and improve transient response. Proper

capacitor selection is important to ensure proper

operation. The APL1117 output capacitor selection is

dependent upon the ESR (equivalent series resistance)

of the output capacitor to maintain stability. When the

output capacitor is 10uF or greater, the output capacitor

should have an ESR less than 1Ω.This will improve

transient response as well as promote stability. A

low-ESR solid tantalum capacitor works extremely well

and provides good transient response and stability over

temperature.

Aluminum electrolytics can also be used, as long as

the ESR of the capacitor is <1Ω. The value of the output

capacitor can be increased without limit. Higher

capacitance values help to improve transient response

and ripple rejection and reduce output noise.

Figure 2. Connections for Best Load Regulation

Application Information (Cont.)

Load Regulation (Cont.)

VIN

APL1117

OUTIN ADJ

PARASITIC

LINE RESISTANCE

CONNECT

R1 TO CASE

CONNECT

R2 TO LOAD

Ripple Rejection

The curves for Ripple Rejection were generated using

an adjustable device with the adjust pin bypassed. With

a 22µF bypassing capacitor 75dB ripple rejection is

obtainable at any output level. The impedance of the

adjust pin capacitor, at the ripple frequency, should

be < R1. R1 is normally in the range of 100Ω-200Ω.

The size of the required adjust pin capacitor is a

function of the input ripple frequency. At 120Hz, with

R1=100Ω, the adjust pin capacitor should be 13µF.

For fixed voltage devices, and adjustable devices

without an adjust pin capacitor, the output ripple will

increase as the ratio of the output voltage to the

reference voltage (VOUT /VREF ).

Thermal Considerations

The APL1117 regulators have thermal protection to limit

junction temperature to 150ºC. However, device

functionality is only guaranteed to a maximum junction

temperature of +125ºC.

A heatsink may be required depending on the maximum

power dissipation and maximum ambient temperature

of the application. Figure 3&4 show for the TO-252

and SOT-223 the measured values θ(J-A) for different

copper area sizes using a 2 layers, 1.6mm, and 6Sq.

cm FR-4 PCB with 2oz. copper and a ground plane

layer on the backside area used for heatsinking. It

can be used as a rough guideline in estimating thermal

resistance. Both the TO-252 and SOT-223 packages

use a copper plane on the PCB and the PCB itself as

a heatsink. To optimize the heat sinking ability of the

plane and PCB, solder the tab of the package to the

plane.

Rev. C.6 - Mar., 2008

APL1117

www.anpec.com.tw11

Application Information (Cont.)

0 2 4 6 8 10 12 14

Thermal Resistance

(Juntion to Ambient) (°C/W)

TA=25°C

Top Copper Area (cm2)

Figure 3.

θ(J-A) vs. copper area for the TO-252 package

0 2 4 6 8 10 12 14

Thermal Resistance

(Juntion to Ambient) (°C/W)

TA=25°C

Top Copper Area (cm2)

Figure 4.

θ(J-A) vs. copper area for the SOT-223 package

The thermal resistance for each application will be

affected by thermal interactions with other components

on the board. Some experimentation will be necessary

to determine the actual value.

The power dissipation of APL1117 is equal to :

PD = (VIN - VOUT) x IOUT

Figure 5.

Safe Operation Area of APL1117 in TO-252 and

SOT-223 packages (limited by Power Dissipation

with TJUNCTION < 125°C)

Safe Operation Area

Using the experiment result of previous Thermal Con-

sideration (choose the one with 1.5cm * 1.5cm polygen

area) and θ(J-A) = 50°C/W spec, the safe operation area

of APL1117 in TO-252 and SOT-223 packages can be

obtained as Figure 5.

Thermal Considerations (Cont.) Maximum junction temperature is equal to :

TJUNCTION = TAMBIENT + (PD x θJA)

Note: TJUNCTION must not exceed 125°C

200

400

600

800

1000

1200

0.8511.31.45 1.75 2.05 2.35 2.65 2.95 3.1

Input-Output Voltage Differential (V)

Output Current (mA)

TA=85oC

TA=55oC

TA=25oC

Rev. C.6 - Mar., 2008

APL1117

www.anpec.com.tw12

Package Information

TO-220

AA1

E/2

EE2

LMIN. MAX.

4.83

0.51

1.14 1.78

0.36 0.61

14.22 16.51

1.40

12.19

MILLIMETERS

b0.38 1.02

2.54 BSC

TO-220

9.65 10.67

6.86

0.100 BSC

MIN. MAX.

INCHES

0.190

0.020

0.015 0.040

0.045 0.070

0.014 0.024

0.560 0.650

0.480

0.380 0.420

0.270

3.56 0.140 0.055

0.355

0.250

0.580

12.70

8.38 9.02

6.35

14.73 0.500

0.330

H1 5.84 6.86 0.230 0.270

4.09 0.161

2.03A2 2.92 0.080 0.115

E2 0.76 0.030

12.88 0.507

0.350

8.89

3.53 0.139

2.54 3.43 0.100 0.135

Note: Follow JEDEC TO-220 AB.

Rev. C.6 - Mar., 2008

APL1117

www.anpec.com.tw13

Package Informaion

TO252-3

LMIN. MAX.

2.39

4.95 5.46

0.46 0.61

0.13

5.33

MILLIMETERS

b0.50 0.89

2.29 BSC

TO-252

4.57

6.35 6.73

6.22

0.090 BSC

MIN. MAX.

INCHES

0.094

0.020 0.035

0.195 0.215

0.018 0.024

0.210

0.180

0.250 0.265

2.18

0.245

0.086

0.005

0.035

0.070

0.410

9.40

0.90

0.46 0.89

1.78

10.41 0.370

0.035

0.018

0.040

L4 1.02

0.150

3.81

0.89 2.03 0.035 0.080

0 8°

0°8°

0°

0.25

GAUGE PLANE L

VIEW A

SEATING PLANE

L4 L3

SEE VIEW A

6.00

Note : Follow JEDEC TO-252 .

6.00

0.235

Rev. C.6 - Mar., 2008

APL1117

www.anpec.com.tw14

Package Information

TO-263-3

b2 e

VIEW A

0.25

GAUGE PLANE

SEATING PLANE

SEE VIEW A

DL1

LMIN. MAX.

4.83

0.00

1.14 1.78

0.38 0.74

1.14 1.65

0.25

6.00

MILLIMETERS

b0.51 0.99

2.54 BSC

TO263

9.65 11.43

6.22

0.100 BSC

MIN. MAX.

INCHES

0.190

0.000

0.020 0.039

0.045 0.070

0.015 0.029

0.045 0.065

0.236

0.380 0.450

0.245

4.06 0.160 0.010

0.380

0.066

0.110

1.78

8.38 9.65

1.68

2.79 0.070

0.330

H14.61 15.88 0.575 0.625

1.78 0.070

9.00

0.354

Note : Follow JEDEC TO-263 AB.

080

Rev. C.6 - Mar., 2008

APL1117

www.anpec.com.tw15

Package Information

SOT-223

VIEW A

0.25

GAUGE PLANE

SEATING PLANE

SEE

VIEW A

LMIN. MAX.

1.80

0.02

0.66 0.84

2.90 3.10

0.23 0.33

0.10

6.70

MILLIMETERS

A2 1.50 1.70

2.30 BSC

SOT-223

3.30 3.70

6.30 6.70

7.30

0.091 BSC

MIN. MAX.

INCHES

0.071

0.001

0.059 0.067

0.026 0.033

0.114 0.122

0.009 0.013

0.264

0.130 0.146

0.248 0.264

0.287

0.004

L0.75 0.030

e1 4.60 BSC 0.181 BSC

Note : 1. Follow from JEDEC TO-261 AA.

2. Dimension D and E1 are determined at the outermost extremes

of the plastic exclusive of mold flash, tie bar burrs, gate burrs,

and interlead flash, but including any mismatch between the top

and bottom of the plastic body.

Rev. C.6 - Mar., 2008

APL1117

www.anpec.com.tw16

Carrier Tape & Reel Dimension

OD0

BA0

SECTION B-B

SECTION A-A

OD1

Application

A H T1 C d D W E1 F

320.0±2.00

50 MIN.

12.4+2.00

-0.00

13.0+0.50

-0.20

1.5 MIN.

20.2 MIN.

12.00±0.30

1.75±0.10

5.50±0.05

P0 P1 P2 D0 D1 T A0 B0 K0

SOT-223

4.00±

0.10

8.00±

0.10

2.00±

0.50

1.5+0.10

-0.00

1.5 MIN.

0.6+0.00

-0.40

6.90±

0.20

7.50±

0.20

2.10±

0.20

Application

A H T1 C d D W E1 F

330.0±2.00

50 MIN.

16.4+2.00

-0.00

13.0+0.50

-0.20

1.5 MIN.

20.2 MIN.

16.0±0.30

1.75±0.10

7.50±0.05

P0 P1 P2 D0 D1 T A0 B0 K0

TO-252-3

4.0±0.10

8.0±0.10

2.0±0.05

1.5+0.10

-0.00

1.5 MIN.

0.6+0.00

-0.40

6.80±0.20

10.40±0.20

2.50±0.20

Application

A H T1 C d D W E1 F

381.0±

2.00

60 MIN.

24.4+2.00

-0.00

13.0+0.50

-0.20

1.5 MIN.

20.2 MIN.

24.0±

0.30

1.75±

0.10

11.5±

0.10

P0 P1 P2 D0 D1 T A0 B0 K0

TO-263-3

4.0±0.10

16.0±0.10

2.0±0.10

1.5+0.10

-0.00

1.5 MIN.

0.6+0.00

-0.40

10.8±0.20

16.1±0.20

5.2±0.20

(mm)

Rev. C.6 - Mar., 2008

APL1117

www.anpec.com.tw17

Devices Per Unit

Package Type Unit Quantity

TO252-3 Tape & Reel 2500

TO-263-3 Tape & Reel 1000

SOT-223 Tape & Reel 2500

Test item Method Description

SOLDERABILITY MIL-STD-883D-2003 245°C, 5 sec

HOLT MIL-STD-883D-1005.7 1000 Hrs Bias @125°C

PCT JESD-22-B, A102 168 Hrs, 100%RH, 121°C

TST MIL-STD-883D-1011.9 -65°C~150°C, 200 Cycles

ESD MIL-STD-883D-3015.7 VHBM > 2KV, VMM > 200V

Latch-Up JESD 78 10ms, 1tr > 100mA

Reflow Condition (IR/Convection or VPR Reflow)

t 25 C to Peak

Ramp-up

Ramp-down

Preheat

Tsmax

Tsmin

Temperature

Time

Critical Zone

TL to TP

Reliability Test Program

Rev. C.6 - Mar., 2008

APL1117

www.anpec.com.tw18

Profile Feature Sn-Pb Eutectic Assembly Pb-Free Assembly

Average ramp-up rate

(TL to TP) 3°C/second max. 3°C/second max.

Preheat

- Temperature Min (Tsmin)

- Temperature Max (Tsmax)

- Time (min to max) (ts)

100°C

150°C

60-120 seconds

150°C

200°C

60-180 seconds

Time maintained above:

- Temperature (TL)

- Time (tL) 183°C

60-150 seconds 217°C

60-150 seconds

Peak/Classification Temperature (Tp)

See table 1 See table 2

Time within 5°C of actual

Peak Temperature (tp) 10-30 seconds 20-40 seconds

Ramp-down Rate 6°C/second max. 6°C/second max.

Time 25°C to Peak Temperature 6 minutes max. 8 minutes max.

Note: All temperatures refer to topside of the package. Measured on the body surface.

Table 2. Pb-free Process – Package Classification Reflow Temperatures

Package Thickness Volume mm3

<350 Volume mm3

350-2000 Volume mm3

>2000

<1.6 mm 260 +0°C* 260 +0°C* 260 +0°C*

1.6 mm – 2.5 mm 260 +0°C* 250 +0°C* 245 +0°C*

≥2.5 mm 250 +0°C* 245 +0°C* 245 +0°C*

* Tolerance: The device manufacturer/supplier shall assure process compatibility up to and including the stated

classification temperature (this means Peak reflow temperature +0°C. For example 260°C+0°C) at the rated MSL

level.

Customer Service

Anpec Electronics Corp.

Head Office :

No.6, Dusing 1st Road, SBIP,

Hsin-Chu, Taiwan, R.O.C.

Tel : 886-3-5642000

Fax : 886-3-5642050

Taipei Branch :

2F, No. 11, Lane 218, Sec 2 Jhongsing Rd.,

Sindian City City, Taipei County 23146, Taiwan

Tel : 886-2-2910-3838

Fax : 886-2-2917-3838

Table 1. SnPb Eutectic Process – Package Peak Reflow Temperatures

Package Thickness Volume mm3

<350 Volume mm3

≥350

<2.5 mm 240 +0/-5°C 225 +0/-5°C

≥2.5 mm 225 +0/-5°C 225 +0/-5°C

Classification Reflow Profiles