PCM1744U/2K - Texas Instruments - Datasheet.Directory

1PCM1744

24 Bits, 96kHz,

Sampling Stereo Audio

DIGITAL-TO-ANALOG CONVERTER

PCM1744

DESCRIPTION

The PCM1744 is a complete low cost stereo audio

digital-to-analog converter (DAC), operating off of a

256fS or 384fS system clock. The DAC contains a 3rd-

order ∆Σ modulator, a digital interpolation filter, and

an analog output amplifier. The PCM1744 accepts

24-bit input data in a I2S format.

The digital filter performs an 8x interpolation function

and includes de-emphasis at 44.1kHz. The PCM1744

can accept digital audio sampling frequencies from

16kHz to 96kHz, always at 8X oversampling.

The PCM1744 is ideal for low-cost, CD-quality con-

sumer audio applications.

FEATURES

●COMPLETE STEREO DAC: Includes Digital

Filter and Output Amp

●DYNAMIC RANGE: 95dB

●MULTIPLE SAMPLING FREQUENCIES:

Up to 96kHz

●8x OVERSAMPLING DIGITAL FILTER

●SYSTEM CLOCK: 256fS/384fS

●24-BIT I2S DATA INPUT FORMAT

●SMALL 14-PIN SOIC PACKAGE

International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 • Twx: 910-952-1111

Internet: http://www.burr-brown.com/ • FAXLine: (800) 548-6133 (US/Canada Only) • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132

For most current data sheet and other product

information, visit www.burr-brown.com

Serial

Input

I/F

Mode

Control

I/F

8X Oversampling

Digital Filter

SCKI

256f

/384f

GND

Multi-level

Delta-Sigma

Modulator

OUT

CAP

DAC

Multi-level

Delta-Sigma

Modulator

Low-pass

Filter

Low-pass

Filter

OUT

DAC

FORMAT

LRCIN

DIN

BCKIN

DM Power Supply

PCM1744

SBAS130

PCM1744

SPECIFICATIONS

All specifications at +25°C, +VCC = +5V, fS = 44.1kHz, and 18-bit input data, SYSCLK = 384fS, unless otherwise noted.

The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes

no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change

without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant

any BURR-BROWN product for use in life support devices and/or systems.

PCM1744

PARAMETER CONDITIONS MIN TYP MAX UNITS

RESOLUTION 24 Bits

DATA FORMAT

Audio Data Interface Format I2S

Audio Data Format Two’s Binary Complement

Sampling Frequency (fS)16 96 kHz

Internal System Clock Frequency 256fS/384fS

DIGITAL INPUT/OUTPUT

Logic Level TTL

Input Logic Level

VIH(1) 2.0 VDC

VIL(1) 0.8 VDC

Input Logic Current: IIN(1) ±0.8 µA

DYNAMIC PERFORMANCE(2) f = 991kHz

THD+N at FS (0dB) –83 –79 dB

THD+N at –60dB –32 dB

Dynamic Range EIAJ, A-weighted 90 95 dB

Signal-to-Noise Ratio EIAJ, A-weighted 90 97 dB

Channel Separation 88 95 dB

DC ACCURACY

Gain Error ±1.0 ±10.0 % of FSR

Gain Mismatch, Channel-to-Channel ±1.0 ±5.0 % of FSR

Bipolar Zero Error VOUT = VCC/2 at BPZ ±20 ±50 mV

ANALOG OUTPUT

Output Voltage Full Scale (0dB) 0.62 x VCC Vp-p

Center Voltage VCC/2 VDC

Load Impedance AC Load 10 kΩ

DIGITAL FILTER PERFORMANCE

Passband 0.445 fS

Stopband 0.555 fS

Passband Ripple ±0.17 dB

Stopband Attenuation –35 dB

Delay Time 11.125/fSsec

INTERNAL ANALOG FILTER

–3dB Bandwidth 100 kHz

Passband Response f = 20kHz –0.16 dB

POWER SUPPLY REQUIREMENTS

Voltage Range 4.5 5 5.5 VDC

Supply Current 13 18 mA

Power Dissipation 65 90 mW

TEMPERATURE RANGE

Operation –25 +85 °C

Storage –55 +125 °C

NOTES: (1) Pins 1, 2, 3, 12, 13, 14: LRCIN, DIN, BCKIN, DM, FORMAT, SCKI. (2) Dynamic performance specs are tested with 20kHz low pass filter and THD+N

specs are tested with 30kHz LPF, 400Hz HPF, Average-Mode.

3PCM1744

PIN ASSIGNMENTS

PIN NAME I/O FUNCTION

1(1) LRCIN IN Sample Rate Clock Input

2(1) DIN IN Audio Data Input

3(1) BCKIN IN Bit Clock Input for Audio Data.

4 NC — No Connection

5 CAP — Common Pin of Analog Output Amp

OUTR OUT Right-Channel Analog Output

7 GND — Ground

CC — Power Supply

OUTL OUT Left-Channel Analog Output

10 NC — No Connection

11 NC — No Connection

12(2) DM IN De-Emphasis Control

HIGH: De-emphasis ON

LOW: De-emphasis OFF

13(2) TEST — Test Pin. Must be left open.

14(1) SCKI IN System Clock Input (256fS or 384fS)

NOTE: (1) Schmitt-Trigger input. (2) Schmitt-Trigger input with internal pull-up.

PIN CONFIGURATION

TOP VIEW SOIC

ABSOLUTE MAXIMUM RATINGS

Power Supply Voltage ......................................................................+6.5V

+VCC to +VDD Difference ................................................................... ±0.1V

Input Logic Voltage .................................................. –0.3V to (VDD + 0.3V)

Power Dissipation .......................................................................... 290mW

Operating Temperature Range ......................................... –25°C to +85°C

Storage Temperature...................................................... –55°C to +125°C

Lead Temperature (soldering, 5s).................................................. +260°C

Thermal Resistance,

JA ..............................................................+90°C/W

ELECTROSTATIC

DISCHARGE SENSITIVITY

This integrated circuit can be damaged by ESD. Burr-Brown

recommends that all integrated circuits be handled with

appropriate precautions. Failure to observe proper handling

and installation procedures can cause damage.

ESD damage can range from subtle performance degradation

to complete device failure. Precision integrated circuits may

be more susceptible to damage because very small parametric

changes could cause the device not to meet its published

specifications.

PACKAGE SPECIFIED

DRAWING TEMPERATURE PACKAGE ORDERING TRANSPORT

PRODUCT PACKAGE NUMBER(1) RANGE MARKING NUMBER(2) MEDIA

PCM1744 SO-14 235 –25°C to +85°C PCM1744U PCM1744U Rails

" " " " PCM1744U PCM1744U/2K Tape and Reel

NOTES: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book, or visit the Burr-Brown web site

at www.burr-brown.com. (2) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /2K indicates 2000 devices per reel). Ordering

2000 pieces of “PCM1744U/2K” will get a single 2500-piece Tape and Reel. For detailed Tape and Reel mechanical information, refer to Appendix B of Burr-Brown

IC Data Book.

PACKAGE/ORDERING INFORMATION

LRCIN

DIN

BCKIN

CAP

OUT

GND

SCKI

TEST

OUT

PCM1744

TYPICAL PERFORMANCE CURVES

At TA = +25°C, +VCC = +5V, fS = 44.1kHz, SYSCLK = 256fS, unless otherwise noted.

DYNAMIC PERFORMANCE

THD+N vs TEMPERATURE

Temperature (°C)

THD+N at 0dB (%)

0.009

0.008

0.007

0.006

0.005

0.004

0.003

0.002

0.001

0–25 0 25 50 75 85 100

THD+N at –60dB (%)

3.2

3.1

3.0

2.9

2.8

2.7

2.6

2.5

2.4

2.3

–60dB

0dB

SNR, DYNAMIC RANGE vs TEMPERATURE

Temperature (°C)

SNR (dB)

–25 0 25 50 75 85 100

Dynamic Range (dB)

Dynamic Range

SNR

THD+N vs POWER SUPPLY

(V)

THD+N at 0dB (%)

0.009

0.008

0.007

0.006

0.005

0.004

0.003

0.002

0.001

04.5 4.75 5.0 5.25 5.5

THD+N at –60dB (%)

3.2

3.1

3.0

2.9

2.8

2.7

2.6

2.5

2.4

2.3

–60dB

0dB

SNR, DYNAMIC RANGE vs POWER SUPPLY

(V)

SNR (dB)

4.5 4.75 5.0 5.25 5.5

Dynamic Range (dB)

Dynamic Range

SNR

THD+N vs SAMPLING RATE

Sampling Rate (kHz)

THD+N at 0dB (%)

0.016

0.014

0.012

0.01

0.008

0.006

0.004

5.2

4.7

4.2

3.7

3.2

2.7

2.2

44.1 48 88.2 96

THD+N AT –60dB (%)

–60dB

0dB

SNR, DYNAMIC RANGE vs SAMPLING RATE

Sampling Rate (kHz)

SNR (dB)

44.1 48 88.2 96

Dynamic Range (dB)

Dynamic Range

SNR

5PCM1744

TYPICAL PERFORMANCE CURVES

At TA = +25°C, +VCC = +VDD = +5V, fS = 44.1kHz, and 18-bit input data, SYSCLK = 384fS, unless otherwise noted.

DIGITAL FILTER

0 0.4536f

1.3605f

2.2675f

3.1745f

4.0815f

–20

–40

–60

–80

–100

OVERALL FREQUENCY CHARACTERISTIC

Frequency (Hz)

PASSBAND RIPPLE CHARACTERISTIC

–0.2

–0.4

–0.6

–0.8

–1 0 0.1134fS0.2268fS0.3402fS0.4535fS

Frequency (Hz)

DE-EMPHASIS FREQUENCY RESPONSE (44.1kHz)

Frequency (kHz)

Level (dB)

–2

–4

–6

–8

–10

–12 0 5 10 15 20 25

DE-EMPHASIS FREQUENCY ERROR (44.1kHz)

Frequency (kHz)

Error (dB)

0.6

0.4

0.2

0.0

–0.2

–0.4

–0.6 0 4999.8375 9999.675 14999.5125 19999.35

PCM1744

FIGURE 1. I2S Data Input Timing.

FIGURE 2. Audio Data Input Timing.

SYSTEM CLOCK

The system clock for PCM1744 must be either 256fS or

384fS, where fS is the audio sampling frequency (LRCIN),

typically 32kHz, 44.1kHz, 48kHz, 88.2kHz or 96kHz. The

system clock is used to operate the digital filter and the noise

shaper. The system clock input (SCKI) is at pin 14. Timing

conditions for SCKI are shown in Figure 3.

PCM1744 has a system clock detection circuit which auto-

matically detects the frequency, either 256fS or 384fS. The

system clock should be synchronized with LRCIN (pin 1),

but PCM1744 can compensate for phase differences. If the

phase difference between LRCIN and system clock is greater

System Clock Pulse Width High tSCKIH 13ns (min)

System Clock Pulse Width Low tSCKIL 13ns (min)

FIGURE 3. System Clock Timing Requirements.

LRCKIN

BCKIN

DIN

1.4V

BCH

BCL

BCKIN Pulse Cycle Time

BCKIN Pulse Width High

BCKIN Pulse Width Low

BCKIN Rising Edge to LRCIN Edge

LRCIN Edge to BCKIN Rising Edge

DIN Set-up Time

DIN Hold Time

: t

BCY

: t

BCH

: t

BCL

: t

: 100ns (min)

: 50ns (min)

: 30ns (min)

BCY

tSCKIH

SCKI

tSCKIL

2.0V

0.8V

123 20 21

1/f

L_ch R_ch

MSB LSB

22 23 24 2120 22 23 24

LRCIN (pin 1)

BCKIN (pin 3)

AUDIO DATA WORD = 24-BIT

DIN (pin 2) 123

MSB LSB

7PCM1744

than ±6 bit clocks (BCKIN), the synchronization is per-

formed automatically. The analog outputs are forced to a

bipolar zero state (VCC/2) during the synchronization func-

tion. Table I shows the typical system clock frequency

inputs for the PCM1744.

SYSTEM CLOCK

FREQUENCY (MHz)

256fS384fS

32kHz 8.192 12.288

44.1kHz 11.2896 16.9340

48kHz 12.288 18.432

88.2kHz 22.5792 33.868

96kHz 24.576 36.864

SAMPLING

RATE (LRCIN)

TABLE I. System Clock Frequencies vs Sampling Rate.

TYPICAL CONNECTION DIAGRAM

Figure 4 illustrates the typical connection diagram for

PCM1744 used in a stand-alone application.

INPUT DATA FORMAT

PCM1744 can accept input data a 24-bit I2S format, as

shown in Figure 1.

FIGURE 5. Internal Power-On Reset Timing.

FIGURE 4. Typical Connection Diagram.

RESET

PCM1744 has an internal power-on reset circuit. The internal

power-on reset initializes (resets) when the supply voltage

VCC > 2.2V (typ). The power-on reset has an initialization

period equal to 1024 system clock periods after VCC > 2.2V.

During the initialization period, the outputs of the DAC are

invalid, and the analog outputs are forced to VCC/2. Figure 5

illustrates the power-on reset and reset-pin reset timing.

DE-EMPHASIS CONTROL

Pin 12 (DM) enables PCM1744’s de-emphasis function. De-

emphasis operates only at 44.1kHz.

0 De-emphasis OFF

1 De-emphasis ON (44.1kHz)

TABLE II. De-emphasis Control Selection.

1024 system (= SCKI) clocks

Reset Reset Removal

2.6V

2.2V

1.8V

Internal Reset

SCKI Clock

DIN

BCKIN

LRCIN

TEST

SCKI

PCM

Audio Data

Processor

256f

384f

System Clock

GND

De-Emphasis Control

Lch Analog Out

+5V Analog

Rch Analog Out

OUT

CAP

PCM1744

+10µF

Post

LPF

Post

LPF

10µF

PCM1744

APPLICATION

CONSIDERATIONS

DELAY TIME

There is a finite delay time in delta-sigma converters. In A/D

converters, this is commonly referred to as latency. For a

delta-sigma D/A converter, delay time is determined by the

order number of the FIR filter stage, and the chosen sampling

rate. The following equation expresses the delay time of

PCM1744:

TD = 11.125 x 1/fS

For fS = 44.1kHz, TD = 11.125/44.1kHz = 251.4µs

Applications using data from a disc or tape source, such as

CD audio, CD-Interactive, Video CD, DAT, Minidisc,

etc., generally are not affected by delay time. For some

professional applications such as broadcast audio for stu-

dios, it is important for total delay time to be less than 2ms.

OUTPUT FILTERING

For testing purposes all dynamic tests are done on the

PCM1744 using a 20kHz low-pass filter. This filter limits

the measured bandwidth for THD+N, etc. to 20kHz. Failure

to use such a filter will result in higher THD+N and lower

SNR and dynamic range readings than are found in the

specifications. The low-pass filter removes out-of-band noise.

Although it is not audible, it may affect dynamic specifica-

tion numbers.

The performance of the internal low pass filter from DC to

24kHz is shown in Figure 6. The higher frequency roll-off of

the filter is shown in Figure 7. If the user’s application has

the PCM1744 driving a wideband amplifier, it is recom-

mended to use an external low-pass filter. A simple 3rd-

order filter is shown in Figure 8. For some applications, a

passive RC filter or 2nd-order filter may be adequate.

BYPASSING POWER SUPPLIES

The power supplies should be bypassed as close as possible

to the unit. It is also recommended to include a 0.1µF ceramic

capacitor in parallel with the 10µF tantalum bypass capacitor.

FIGURE 6. Low-Pass Filter Frequency Response.

FIGURE 7. Low-Pass Filter Wideband Frequency Response.

FIGURE 8. 3rd-Order LPF.

1.0

0.5

–0.5

–1.0

20 Frequency (Hz)

100 1k 10k 24k

INTERNAL ANALOG FILTER FREQUENCY RESPONSE

(20Hz~24kHz, Expanded Scale)

–5

–10

–15

–20

–25

–30

–35

–40

–45

–50

–55

10 100 1k 10k 100k 1M 10M

Frequency (Hz)

–60

INTERNAL ANALOG FILTER FREQUENCY RESPONSE

(10Hz~10MHz)

10kΩ

1500pF

100pF

680pF

SIN

–

–90

–180

–270

–360

100 1k 10k 100k 1M

GAIN vs FREQUENCY

Frequency (Hz)

Phase (°)

–14

–34

–54

–74

–94

Gain (dB)

Gain

Phase

OPA134

9PCM1744

FIGURE 9. 5-Level ∆Σ Modulator Block Diagram.

FIGURE 10. Quantization Noise Spectrum.

THEORY OF OPERATION

The delta-sigma section of PCM1744 is based on a 5-level

amplitude quantizer and a 3rd-order noise shaper. This

section converts the oversampled input data to 5-level delta-

sigma format. A block diagram of the 5-level delta-sigma

modulator is shown in Figure 9. This 5-level delta-sigma

modulator has the advantage of stability and clock jitter over

the typical one-bit (2-level) delta-sigma modulator.

The combined oversampling rate of the delta-sigma modu-

lator and the internal 8x interpolation filter is 96fS for a

384fS system clock, and 64fS for a 256fS system clock. The

theoretical quantization noise performance of the 5-level

delta-sigma modulator is shown in Figure 10.

5-LEVEL DELTA SIGMA MODULATOR

Frequency (kHz)

Gain (–dB)

–20

–40

–60

–80

–100

–120

–140

–160 0 5 10 15 20 25

Out

48f

(384f

)

64f

(256f

)

In 8f

24-Bit

+++

5-level Quantizer

–

–1

–

–1

PACKAGING INFORMATION

Orderable Device Status (1) Package

Type Package

Drawing Pins Package

Qty Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)

PCM1744U ACTIVE SOIC D 14 50 Green (RoHS &

no Sb/Br) CU NIPDAU Level-1-260C-UNLIM

PCM1744U/2K ACTIVE SOIC D 14 2000 Green (RoHS &

no Sb/Br) CU NIPDAU Level-1-260C-UNLIM

PCM1744U/2KG4 ACTIVE SOIC D 14 2000 Green (RoHS &

no Sb/Br) CU NIPDAU Level-1-260C-UNLIM

PCM1744UG4 ACTIVE SOIC D 14 50 Green (RoHS &

no Sb/Br) CU NIPDAU Level-1-260C-UNLIM

(1) The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in

a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check

http://www.ti.com/productcontent for the latest availability information and additional product content details.

TBD: The Pb-Free/Green conversion plan has not been defined.

Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements

for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered

at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.

Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and

package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS

compatible) as defined above.

Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame

retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)

(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder

temperature.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is

provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the

accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take

reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on

incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited

information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI

to Customer on an annual basis.

PACKAGE OPTION ADDENDUM

www.ti.com 6-May-2008

Addendum-Page 1

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package

Type Package

Drawing Pins SPQ Reel

Diameter

(mm)

Reel

Width

W1 (mm)

A0 (mm) B0 (mm) K0 (mm) P1

(mm) W

(mm) Pin1

Quadrant

PCM1744U/2K SOIC D 14 2000 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1

PACKAGE MATERIALS INFORMATION

www.ti.com 11-Mar-2008

Pack Materials-Page 1

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

PCM1744U/2K SOIC D 14 2000 346.0 346.0 33.0

PACKAGE MATERIALS INFORMATION

www.ti.com 11-Mar-2008

Pack Materials-Page 2

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,and other changes to its products and services at any time and to discontinue any product or service without notice. Customers shouldobtain the latest relevant information before placing orders and should verify that such information is current and complete. All products aresold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standardwarranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except wheremandated by government requirements, testing of all parameters of each product is not necessarily performed.TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products andapplications using TI components. To minimize the risks associated with customer products and applications, customers should provideadequate design and operating safeguards.TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Informationpublished by TI regarding third-party products or services does not constitute a license from TI to use such products or services or awarranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectualproperty of the third party, or a license from TI under the patents or other intellectual property of TI.Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompaniedby all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptivebusiness practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additionalrestrictions.

Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids allexpress and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is notresponsible or liable for any such statements.TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonablybe expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governingsuch use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, andacknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their productsand any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may beprovided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products insuch safety-critical applications.TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products arespecifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet militaryspecifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely atthe Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products aredesignated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designatedproducts in automotive applications, TI will not be responsible for any failure to meet such requirements.Following are URLs where you can obtain information on other Texas Instruments products and application solutions:Products ApplicationsAmplifiers amplifier.ti.com Audio www.ti.com/audioData Converters dataconverter.ti.com Automotive www.ti.com/automotiveDSP dsp.ti.com Broadband www.ti.com/broadbandClocks and Timers www.ti.com/clocks Digital Control www.ti.com/digitalcontrolInterface interface.ti.com Medical www.ti.com/medicalLogic logic.ti.com Military www.ti.com/militaryPower Mgmt power.ti.com Optical Networking www.ti.com/opticalnetworkMicrocontrollers microcontroller.ti.com Security www.ti.com/securityRFID www.ti-rfid.com Telephony www.ti.com/telephonyRF/IF and ZigBee® Solutions www.ti.com/lprf Video & Imaging www.ti.com/videoWireless www.ti.com/wireless