Supplier : Samsung electro-mechanics CL10C151JB81PNC
Product : Multi-layer Ceramic Capac itor CAP, 150, 50V, ± 5%, C0G, 0603
AEC-Q200 Qualified
A. Dimension
Dimension
B. Samsung P art Number
CL 10 C J B 8 1 P N C
②③ ⑤⑥ ⑨⑩⑪
Series Samsung Multi-layer Ceramic Capacitor
Size (inch code) L: 1.60±0.10 mm W: 0.80±0.10 mm
Dielectric C0G Inner ele ctrode Ni
Capacitance 150 Termination Cu
Capacitance ± 5% Plating Sn 100% (Pb Free)
tolerance Product Automotive
Rated Voltage 50 V Special code Normal
Thickness 0.80±0.10 mm Packaging Cardboard Type, 7" Reel
C. Reliability Test and Judgement condition
High Temperature Appearance : No abnormal exterior appearance Unpowered, 1,000hrs @ Max. temperature
Exposure Capacitance Change : Within ±2.5% or ±0.25Measurement at 24±2hrs after test conclusion
whichever is larger
Q : 1,000 min.
IR : More than 10,000 or 500 ×
Whichever is smaller
Temp erature Cycling Appearance : No abnormal exterior appearance 1,000Cycles
Capacitance Change : Within ±2.5% or ±0.25Measurement at 24±2hrs after test conclusion
whichever is larger
Q : 1,000 min. 1 cycle condition : -55+0/-3(30±3min) Room Temp. (1min)
IR : More than 10,000 or 500 × 125+3/-0(30±3min) Room Temp. (1min)
Whichever is smaller
Destructive Phy si cal No Defects or abnormalities Per EIA 469
Analysis
Humid ity Bi as Appearance : No abnormal exterior appearance 1,000hrs 85/85%RH, Rated Voltage and 1.3~1.5V,
Capacitance Change : Within ±2.5% or ±0.25Add 100kohm resistor
whichever is larger
Q : 200 min. The charge/discharge current is less than 50mA.
IR : More than 500 or 25 ×
Whichever is smaller
High Temperature Appearance : No abnormal exterior appearance 1,000hrs @ 125 , 200% Rated Voltage,
Operating Life Capacitance Change : Within ±3% or ±0.3Measurement at 24±2hrs after test conclusion
whichever is larger The charge/discharge current is less than 50mA.
Q : 350 min.
IR : More than 1,000 or 50 ×
Whichever is smaller
0603 inch
1.60±0.10 mm
0.80±0.10 mm
Size
Performance Test condition
0.80±0.10 mm
Specification of Automotive MLCC
(Reference sheet)
0.30±0.20 mm
Samsung P/ N :
Description :
0603
L
W
T
BW
151
External Visual No abnormal exterior appearance Microscope (´10)
Physical Dimensions Within the specified dimensions Using The calipers
Mechanical Shock Appearance : No abnormal exterior appearance Three shocks in each direction should be applied along
Capacitance Change : Within ±2.5% or ±0.253 mutually perpendicular axes of the test specimen (18 shocks)
whichever is larger
Q, IR : Initial spec.
Vibration Appearance : No abnormal exterior appearance 5g's for 20min., 12cycles each of 3 orientations,
Capacitance Change : Within ±2.5% or ±0.25Use 8"×5" PCB 0.031" Thick 7 secure points on one long side
whichever is larger and 2 secure points at corners of opposite sides. Parts mounted
within 2" from any secure point. Test from 10~2,000.
Q, IR : Initial spec.
Resistance to Appearance : No abnormal exterior appearance Preheating : 150 for 60~120 sec.
Solder Heat Capacitance Change : Within ±2.5% or ±0.25Solder pot : 260±5, 10±1sec.
whichever is larger
Q, IR : Initial spec.
ESD Appearance : No abnormal exterior appearance AEC-Q200-002 or ISO/DIS10605
Capacitance Change : Within ±2.5% or ±0.25
whichever is larger
Q, IR : Initial spec.
Solderability 95% of the terminations is to be soldered a) Preheat at 155 for 4 hours, Immerse in solder for 5s at 245±5
evenly and continuously b) Steam aging for 8 hours, Immerse in solder for 5s at 245±5
c) Steam aging for 8 hours, Immerse in solder for 120s at 260±5
solder : a solution ethanol and rosin
Electrical Capacitance : Within specified tolerance The Capacitance / D.F. should be measured at 25,
Characterization Q : 1,000 min. 1 ± 10%, 0.5~5 Vrms
IR(25) : More than 100,000 or 1,000 ×I.R. should be measured with a DC voltage not exceeding
Whichever is smaller. Rated Voltage @25, @125 for 60~120 sec.
IR(125) : More than 10,000 or 100 ×
Whichever is smaller.
Dielectric Strength Dielectric Strength : 300% of the rated voltage for 1~5 seconds
Board Flex Appearance : No abnormal exterior appearance Bending to the limit, 3 for 60 seconds
Capacitance Change : Within ±5% or ±0.5
whichever is larger
Terminal Appearance : No abnormal exterior appearance 10 N, for 60 sec.
Strength(SMD) Capacitance Change : Within ±2.5% or ±0.25
whichever is larger
Beam Load Destruction value should be exceed 20 N Beam speed : 0.5±0.05 /sec
Temperature C0G
Characteristics From -55 to 125 , Capacitance change should be within 0±30ppm/
D. Recommended Soldering method :
Reflow ( Reflow Peak Temperature : 260 +0/-5, 30sec. ), Meet IPC/JEDEC J-STD-020 D Standard
Product specifications included in the specifications are effective as of March 1, 2013.
Please be advised that they are standard product specifications for reference only.
We may change, modify or discontinue the product specifications without notice at any time.
So, you need to approve the product specifications before placing an order.
Should you have any question regarding the product specifications, please contact our sales personnel or application engineers.
4.7m/sec
Performance Test condition
Peak value Duration Wave Velocity
1,500G 0.5ms Half sine
● Disclaimer & Limitation of Use and Application
The products listed in this Specification sheet are NOT designed and manufactured for any use
and applications set forth below.
Please note that any misuse of the products deviating from products specifications or information
provided in this Spec sheet may cause serious property damages or personal injury.
We will NOT be liable for any damages resulting from any misuse of the products, specifically
including using the products for high reliability applications as listed below.
If you have any questions regarding this 'Limitation of Use and Application', you should first contact
our sales personnel or application engineers.
Aerospace/Aviation equipment
Medical equipment
Military equipment
Disaster prevention/crime prevention equipment
Power plant control equipment
Atomic energy-related equipment
Undersea equipment
Traffic signal equipment
Data-processing equipment
Electric heating apparatus, burning equipment
Safety equipment
Any other applications with the same as or similar complexity or reliability to the applications