TDA7388 4 x 45 W quad bridge car radio amplifier Datasheet - production data Features High output power capability: - 4 x 45 W / 4 max. - 4 x 26 W / 4 @ 14.4 V, 1 kHz, 10 % Low distortion Low output noise Standby function Mute function Automute at min. supply voltage detection Low external component count: - Internally fixed gain (26 dB) - No external compensation - No bootstrap capacitors '!0'03 Flexiwatt25 Protections: Description Output short circuit to gnd, to VS, across the load Very inductive loads Overrating chip temperature with soft thermal limiter Load dump voltage Fortuitous open GND Reversed battery ESD Table 1. The TDA7388 is an AB class audio power amplifier, packaged in Flexiwatt 25 and designed for high end car radio applications. Based on a fully complementary PNP/NPN configuration, the TDA7388 allows a rail to rail output voltage swing with no need of bootstrap capacitors. The extremely reduced boundary components count allows very compact sets. Device summary Order code Package Packing TDA7388 Flexiwatt25 Tube June 2012 This is information on a product in full production. Doc ID 14256 Rev 4 1/11 www.st.com 1 Contents TDA7388 Contents 1 Pin connection and test/application diagrams . . . . . . . . . . . . . . . . . . . . 5 2 Electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3 2.1 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2.2 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2.3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Application hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3.1 SVR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3.2 Input stage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3.3 Standby and muting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2/11 Doc ID 14256 Rev 4 TDA7388 List of tables List of tables Table 1. Table 2. Table 3. Table 4. Table 5. Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Thermal data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Doc ID 14256 Rev 4 3/11 List of figures TDA7388 List of figures Figure 1. Figure 2. Figure 3. 4/11 Pin connection (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Standard test and application circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Flexiwatt25 mechanical data and package dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Doc ID 14256 Rev 4 TDA7388 Pin connection and test/application diagrams Pin connection (top view) 0 '.$ -54% /54 6## /54 /54 /54 0 '.$ ). !# '.$ ). 3 '.$ ). ). 362 /54 0 '.$ 6## /54 34 "9 /54 /54 0 '.$ .# Figure 1. 4!" 1 Pin connection and test/application diagrams '!0'03 Figure 2. Standard test and application circuit # M& # M& 6CC 6CC 2 34 "9 + 2 # M& -54% + # # M& ). # M& ). /54 # M& ). # M& /54 M& ). /54 3 '.$ # M& /54 362 # M& .# 4!" '!0'03 Doc ID 14256 Rev 4 5/11 Electrical specifications TDA7388 2 Electrical specifications 2.1 Absolute maximum ratings Table 2. Absolute maximum ratings Symbol Parameter Value Unit Operating supply voltage 18 V VS (DC) DC supply voltage 28 V VS (pk) Peak supply voltage (t = 50 ms) 50 V Output peak current: Repetitive (duty cycle 10 % at f = 10 Hz) Non repetitive (t = 100 s) 4.5 5.5 A Power dissipation, (Tcase = 70 C) 80 W Tj Junction temperature 150 C Tstg Storage temperature - 55 to 150 C VS IO Ptot 2.2 Thermal data Table 3. Thermal data Symbol Rth j-case 2.3 Parameter Thermal resistance junction-to-case max. Value Unit 1 C/W Electrical characteristics VS = 14.4 V; f = 1 kHz; Rg = 600 ; RL = 4 ; Tamb = 25 C; Refer to the test and application diagram (Figure 2), unless otherwise specified. Table 4. Symbol Electrical characteristics Parameter Test condition Min. Typ. Max. Unit 120 190 350 mA - - 100 mV Quiescent current RL = VOS Output offset voltage Play mode dVOS During mute ON/OFF output ITU R-ARM weighted offset voltage -80 - +80 mV Gv Voltage gain - 25 26 27 dB Po Output power THD = 10 %; VS = 14.4 V 22 26 - W VS = 14.4 V 37 41 - VS = 15.2 V - 45 - Po = 4 W - 0.04 0.15 Iq1 Po max THD 6/11 Max.output power(1) Distortion Doc ID 14256 Rev 4 W % TDA7388 Table 4. Symbol Electrical specifications Electrical characteristics (continued) Parameter Test condition Min. Typ. Max. Unit "A" Weighted - 50 70 V Bw = 20 Hz to 20 kHz - 70 100 V eNo Output noise SVR Supply voltage rejection f = 100 Hz; Vr = 1 Vrms 50 65 - dB fch High cut-off frequency Po = 0.5 W 100 200 - KHz Ri Input Impedance - 70 100 - K 70 - dB Cross talk f = 1 kHz; Po = 4 W 60 CT f = 10 kHz; Po = 4 W - 60 - dB ISB Standby current consumption VSt-by = 0V - - 20 A VSB out Standby OUT threshold voltage (Amp: ON) 3.5 - - V VSB IN Standby IN threshold voltage (Amp: OFF) - - 1.5 V Mute attenuation POref = 4 W 80 90 - dB VM out Mute OUT threshold voltage (Amp: play) 3.5 - - V VM in Mute IN threshold voltage (Amp: mute) - - 1.5 V VS automute threshold (Amp: mute); Att. 80 dB; POref = 4 W (Amp: play); Att. < 0.1 dB; PO = 0.5 W - VMUTE = 1.2 V (Source current) 5 AM VAM in Ipin22 Muting pin current 6.5 7.6 8.5 11 20 V A 1. Saturated square wave output. Doc ID 14256 Rev 4 7/11 Application hints 3 TDA7388 Application hints Ref. to the circuit of Figure 2. 3.1 SVR Besides its contribution to the ripple rejection, the SVR capacitor governs the turn ON/OFF time sequence and, consequently, plays an essential role in the pop optimization during ON/OFF transients. To conveniently serve both needs, its minimum recommended value is 10 F. 3.2 Input stage The TDA7388's inputs are ground-compatible and can stand very high input signals (8 Vpk) without any performances degradation. If the standard value for the input capacitors (0.1 F) is adopted, the low frequency cut-off amounts to 16 Hz. 3.3 Standby and muting If standby and muting are not used, a straight connection to VS of their respective pins would be admissible. Conventional/low-power transistors can be employed to drive muting and standby pins in absence of true CMOS ports or microprocessors. R-C cells have always to be used in order to smooth down the transitions for preventing any audible transient noises. Since a DC current of about 10 A normally flows out of pin 22, the maximum allowable muting-series resistance (R2) is 70 k, which is sufficiently high to permit a muting capacitor reasonably small (about 1 F). If R2 is higher than recommended, the involved risk is that the voltage at pin 22 may rises to above the 1.5 V threshold voltage and the device consequently fails to turn OFF when the mute line is brought down. About the stand-by, the time constant to be assigned in order to obtain a virtually pop-free transition has to be slower than 2.5 V/ms. 8/11 Doc ID 14256 Rev 4 TDA7388 Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK(R) is an ST trademark. Figure 3. Flexiwatt25 mechanical data and package dimensions $)- ! " # $ % & ' ' ( ( ( ( , , , , , , - . / 2 2 2 2 2 6 6 6 6 -). MM 490 -!8 -). INCH 490 -!8 /54,).% !.$ -%#(!.)#!, $!4! &LEXIWATT VERTICAL 7\S 7\S 7\S 7\S DAM BAR PROTUSION NOT INCLUDED MOLDING PROTUSION INCLUDED 6 # " 6 ( ( 6 ! ( / ( 2 , 2 6 2 , . 2 , 4 Package information , , 6 6 2 $ 2 , 0IN 2 2 % ' ' & &,%8-% - - '!0'03 Doc ID 14256 Rev 4 9/11 Revision history 5 TDA7388 Revision history Table 5. 10/11 Document revision history Date Revision Changes 06-Dec-2007 1 Initial release. 12-Jul-2010 2 Document status promoted from preliminary data to datasheet. 26-Apr-2012 3 Modified Features on page 1. Updated Table 4: Electrical characteristics on page 6. 20_Jun-2012 4 Updated Section 3.3: Standby and muting. Doc ID 14256 Rev 4 TDA7388 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2012 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com Doc ID 14256 Rev 4 11/11