Features * Full Trusted Computing Group (TCG) Trusted Platform Module (TPM) Version 1.2 * * * * * * * * * * * * Compatibility Single-chip Turnkey Solution Hardware Asymmetric Crypto Engine 2048-bit RSA Sign in 500 ms AVR(R) RISC Microprocessor Internal EEPROM Storage for RSA Keys 100 kHz System Management Bus (SMBusTM) Two-wire Interface Secure Hardware and Firmware Design and Chip Layout True Random Number Generator (RNG) - FIPS 140-2 Compliant NV Storage Space for 1280 bytes of user defined data 3.3V 10% Supply Voltage 28-lead TSSOP Package or 40-lead QFN Package 0-70C Temperature Range Trusted Platform Module Description The AT97SC3203S is a fully integrated security module designed to be integrated into embedded systems. It implements version 1.2 of the Trusted Computing Group (TCG) specification for Trusted Platform Modules (TPM). AT97SC3203S The TPM includes a cryptographic accelerator capable of computing a 2048-bit RSA signature in 500 ms and a 1024-bit RSA signature in 100 ms. Performance of the SHA-1 accelerator is 50 s per 64-byte block. In most cases, TCG key generation operations will be completed using a proprietary mechanism in less than 1 msec. SMBus Two-Wire Interface Table 1. Pin Configurations Pin Name Description VCC 3.3V (10%) Supply Voltage SB3V Standby 3.3V ( 10%) Supply Voltage VBAT 2.5-4.0V Battery Input GND Ground RESET# Reset Input Active Low SMBDAT SMBus Data Input/Output SMBCLK SMBus Clock Input AVRCLK 33-MHz AVR Clock Input Xtall/32K in 32.768 kHz Crystal Input XtalO 32.768 kHz Crystal Output GPIO6 General Purpose Input/Output TestI Test Input (disabled) TestBI Test Input (disabled) NC No Connect NBO Not Bonded Out Summary 5132AS-TPM-1/07 Note: This is a summary document. A complete document is available through your local Atmel sales office. Figure 1. Pin Configurations NBO NBO NBO NBO NBO NBO NC NC 40 39 38 37 36 35 34 33 32 31 NC 1 30 NC GND 2 29 GND SB3V 3 28 VCC GPIO6 4 27 NC NC 5 26 NC TestI 6 25 AVRCLK TestBI 7 24 NC VCC 8 23 VCC GND 9 22 GND VBAT 10 NC RESET# NC NBO NBO NBO NBO NBO 21 11 12 13 14 15 16 17 18 19 20 XTALO NC NC NC GND VCC NC NC AVRCLK NC VCC GND NC RESET# NC XTALI/32K in 28 27 26 25 24 23 22 21 20 19 18 17 16 15 SMBCLK 1 2 3 4 5 6 7 8 9 10 11 12 13 14 NBO SMBDAT SMBCLK NC GND SB3V GPIO6 NC TestI TestBI VCC GND VBAT Xtall/32K in XtalO SMBDAT 40-pin QFN 6.0 mm x 6.0 mm Body 0.50 mm Pitch 28-pin TSSOP 6.1 mm x 9.7 mm Body 0.65 mm Pitch Figure 2. AT97SC3203S Block Diagram SMBDAT SMBCLK GPIO6 ROM Program EEPROM Program 33 MHz AVR Clock Input AVR 8-Bit RISC CPU EEPROM Data SMBus Interface GPIO RNG VBAT 32.768 kHz SRAM RTC CRYPTO Engine (Optional) Timer Physical Security Circuitry 2 AT97SC3203S 5132AS-TPM-1/07 AT97SC3203S Description (continued) Communication to and from the TPM occurs through a modified 100-kHz SMBus twowire interface. The TPM includes a hardware random number generator, including a FIPS-approved Pseudo Random Number Generator, that is used for key generation and TCG protocol functions. The RNG is also available to the system to generate random numbers that may be needed during normal operation. The chip uses a dynamic internal memory management scheme to store multiple RSA keys. Other than the standard TCG commands (TPM_FlushSpecific, TPM_Loadkey2), no system intervention is required to manage this internal key cache. Full documentation for TCG primitives can be found on the TCG Web site located at www.trustedcomputinggroup.org. This specification includes only mechanical, electrical and SMBus protocol information 3 5132AS-TPM-1/07 Table 2. Ordering Information 4 Ordering Code Package Operation Range AT97SC3203S-X5A40 28A3 (28-pin TSSOP) lead-free, RoHS Commercial (0 to 70 C) AT97SC3203S-X5M40 40ML1 (40-pin QFN) lead-free, RoHS Commercial (0 to 70 C) AT97SC3203S 5132AS-TPM-1/07 AT97SC3203S Package Drawing 28A3 - TSSOP b L L1 E E1 e End View Top View COMMON DIMENSIONS (Unit of Measure = mm) D A A2 SYMBOL D MIN 9.60 E Side View MAX NOTE 9.70 9.80 2, 5 3, 5 8.10 BSC E1 6.00 6.10 6.20 A - - 1.20 A2 0.80 1.00 1.05 b 0.19 - 0.30 e L L1 Notes: NOM 4 0.65 BSC 0.45 0.60 0.75 1.00 REF 1. This drawing is for general information only. Please refer to JEDEC Drawing MO-153, Variation DB for additional information. 2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15 mm (0.006 in) per side. 3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm (0.010 in) per side. 4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07 mm. 5. Dimension D and E1 to be determined at Datum Plane H. 1/8/02 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 28A3, 28-lead, 6.1 x 9.7 mm Body, 0.65 pitch, Thin Shrink Small Outline Package (TSSOP) DRAWING NO. 28A3 REV. A 5 5132AS-TPM-1/07 40ML1 - QFN A A1 D N A2 A3 1 Pin 1 Indicator 2 3 E Top View L 0 Side View COMMON DIMENSIONS (Unit of Measure = mm) D2 SYMBOL E2 1 2 b 3 6.00 BSC E 6.00 BSC 3.95 4.10 4.25 E2 3.95 4.10 4.25 A - 0.85 0.90 A1 0.0 0.01 0.05 A2 - 0.65 0.70 b NOTE 0.20 REF 0.30 N e Bottom View MAX D2 L PIN1 ID NOM D A3 e Notes: MIN 0.40 0.50 0.50 BSC 0.18 0.23 0.30 2 1. This drawing is for general information only. Refer to JEDEC Drawing MO-220, Variation WJJD-2, for proper dimensions, tolerances, datums, etc. 2. Dimension b applies to metallized terminal and is measured between 0.15 mm and 0.30 mm from the terminal tip. If the terminal has the optional radius on the other end of the terminal, the dimension should not be measured in that radius area. 3/9/04 R 6 2325 Orchard Parkway San Jose, CA 95131 TITLE 40ML1, 40-lead 6.0 x 6.0 mm Body, 0.50 mm Pitch, Molded Quad Flat No Lead Package (MLF2) DRAWING NO. 40ML1 REV. A AT97SC3203S 5132AS-TPM-1/07 AT97SC3203S Revision History Doc. Rev. Date Comments 5132AS 1/2007 Implemented revision history Added `Summary' to page 1 Revised summary disclaimer text on page 1 7 5132AS-TPM-1/07 Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Atmel Operations Memory 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60 ASIC/ASSP/Smart Cards RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Biometrics Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-47-50 Fax: (33) 4-76-58-47-60 Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL'S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL'S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel's products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. (c)2007 Atmel Corporation. All rights reserved. Atmel (R), logo and combinations thereof, Everywhere You Are (R), AVR(R), SMBus TM and others, are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Printed on recycled paper. 5132AS-TPM-1/07