SPECIFICATION
MODEL PLN-30-9 PLN-30-15PLN-30-12 PLN-30-20 PLN-30-24 PLN-30-27 PLN-30-36 PLN-30-48
DCVOLTAGE
RATEDCURRENT
CURRENTRANGE
RATEDPOWER
OUTPUT VOLTAGE ADJ.RANGE Note.5
CURRENT ADJ.RANGE Note.5
LINEREGULATION
LOADREGULATION
SETUP TIME
VOLTAGERANGE
FREQUENCY RANGE
POWERFACTOR
EFFICIENCY(Typ.)
ACCURRENT
INPUT
INRUSHCURRENT(max.)
LEAKAGECURRENT
SAFETY STANDARDS
WITHSTANDVOLTAGE
ISOLATIONRESISTANCE
WORKINGTEMP.
WORKINGHUMIDITY
STORAGETEMP.,HUMIDITY
TEMP.COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVERCURRENT Note.4
SHORTCIRCUIT
OVERVOLTAGE
OVERTEMPERATURE
9V 15V
10.5~15V
12V
8.4~12V
20V
14~20V
24V
16.8~24V
27V
18.9~27V
36V
25.2~36V
48V
33.6~48V
3.3A 2A2.5A 1.5A 1.25A 1.12A 0.84A 0.63A
0~3.3A 0~2A0~2.5A 0~1.5A 0~1.25A 0~1.12A 0~0.84A 0~0.63A
29.7W 30W30W 30W 30W 30.24W 30.24W 30.24W
2.6Vp-p 2.6Vp-p2Vp-p 2.6Vp-p 2.6Vp-p 2.3Vp-p 4.5Vp-p 3.7Vp-p
-5%~10%.CanbeadjustedbyinternalpotentialmeterSVR1
3%~-25%.CanbeadjustedbyinternalpotentialmeterSVR2
3.0%
10%
5.0%
1500ms/230VAC30 atfullload00ms/115VAC
90~264VAC 127~370VDC
47~63Hz
PF 0.9at75~100%load,115VAC/230VAC
80% 83.5%82.5% 84% 84% 84.5% 85% 85.5%
10~14V 17~22V14~16V 23~26V 27~34V 31~35V 40~50V 53~63V
0.4A/115VAC0.2A/230VAC
40A/230VAC
<0.5mA /240VAC
100~110%
Protectiontype:Constantcurrentlimiting,recoversautomaticallyafterfaultconditionisremoved
Hiccupmode,recoversautomaticallyafterfaultconditionisremoved.
I/P-O/P:3.75KVAC
I/P-O/P:100MOhms/500VDC/25 /70%RH
-30~+50 (Refertooutputloadderatingcurve)
20~95%RH non-condensing
-40~+80 ,10~95%RH
0.06%/ (0~50 )
10~500Hz,2G12min./1cycle,periodfor72min.eachalongX, Y,Zaxes
621.4Khrsmin.MIL-HDBK-217F(25 )
145*47*30mm(L*W*H)
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
Direct connecting to LEDs is not suggested for models with RIPPLE & NOISE > 10% and using additional drivers is highly recommended.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Please refer to OLP characteristics.
5. Output voltage can be adjusted through the SVR1 on the PCB; limit of output constant current level can be adjusted through the SVR2 on the PCB.
6. Constant current operation region is within 70% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please
reconfirm special electrical requirements for some specific system design.
7. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
FileName:PLN-30-SPEC2009-11-25
0.22Kg;60pcs/14.2Kg/1.25CUFT
Protectiontype: Shutdowno/pvoltage,re-powerontorecover
30WSingleOutputLEDPowerSupply
Universal AC input / Full range
Fully isolated plastic case with IP64 level
Built-in constant current limiting circuit with adjustable OCP level
Protections:Short circuit/Over load/Over voltage/Over temperature
Built-in active PFC function
IP64 design for indoor or outdoor installations
Cooling by free air convection
100% full load burn-in test
High reliability
Suitable for LED lighting and moving sign applications
Compliance to worldwide safety regulations for lighting
2 years warranty
(Note.2)
Features :
PLN-30 series
RIPPLE&NOISE(max.) Note.2
VOLTAGETOLERANCE Note.3
ENVIRONMENT
SAFETY &
EMC
PROTECTION
95 10 (TSW1)
Protectiontype:Shutdowno/pvoltage,re-powerontorecover
TUVEN61347-1,EN61347-2-13,CAN/CSA C22.2No.223-M91(exceptfor48V),IP64approved
IP64
( except for 48V )
F M M
110 LPS
SELV
EQUIVALENT
6.3~9V
CONSTANTCURRENTREGION Note.6
HARMONICCURRENT
EMSIMMUNITY
CompliancetoEN55015
CompliancetoEN61000-3-2ClassC(pin 25W),ClassD(>70%load);EN61000-3-3
CompliancetoEN61000-4-2,3,4,5,6,8,11;ENV50204,EN55024,EN61547,lightindustrylevel,criteria A
EMICONDUCTION&RADIATION