CONSTANT CURRENT REGION
Note.4
SPECIFICATION
MODEL
DC VOLTAGE
RATED CURRENT
RATED POWER
OUTPUT
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME Note.6
HOLD UP TIME (Typ.)
VOLTAGE RANGE Note.5
FREQUENCY RANGE
POWER FACTOR (Typ.)
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INPUT
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
SAFETY STANDARDS
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVER CURRENT Note.4
OVER VOLTAGE
OVER TEMPERATURE
2500ms, 200ms / 115VAC at full load 500ms, 200ms / 230VAC at full load
12ms at full load 115VAC/230VAC
90 ~ 305VAC 127 ~ 431VDC
47 ~ 63Hz
PF>0.98/115VAC, PF>0.95/230VAC, PF>0.92/277VAC at full load (Please refer to "Power Factor Characteristic" curve)
1.7A / 115VAC 0.78A / 230VAC 0.7A / 277VAC
COLD START 65A(twidth=425 s measured at 50% Ipeak) at 230VACμ
<0.75mA / 277VAC
95 ~ 108%
Protection type : Constant current limiting, recovers automatically after fault condition is removed
-40 ~ +60 (Refer to "Derating Curve")℃
20 ~ 95% RH non-condensing
-40 ~ +80 , 10 ~ 95% RH℃
±℃ ℃0.03%/ (0 ~ 50 )
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
252.3Khrs min. MIL-HDBK-217F (25 )℃
Refer to mechanical specification
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Constant current operation region is within 60% ~100% rated output voltage, and the output power must be more than 60% rated output power.
This is the suitable operation region for LED related applications, but please reconfirm special electrical requirements for some specific system design.
5. Derating may be needed under low input voltages. Please check the static characteristics for more details.
6. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time.
7. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
8.To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently
connected to the mains.
1.53Kg; 8pcs/13.8Kg/1.61CUFT
Protection type : Shut down o/p voltage with auto-recovery or re-power on to recovery
160W Single Output Switching Power Supply
MEAN WELL patented housing design
(Patent No.: )CN201220314551
Universal AC input / Full range (up to 305VAC)
Built-in active PFC function
High efficiency up to 93.5%
Protections: Short circuit / Over current / Over voltage / Over temperature
OCP point adjustable through internal potentiometer
IP67 / IP65 design for indoor or outdoor installations
Suitable for dry / damp / wet locations
5 years warranty, Tc70 40000hrs℃
â– Features :
HBG-160 series
RIPPLE & NOISE (max.) Note.2
VOLTAGE TOLERANCE
Note.3
ENVIRONMENT
SAFETY &
EMC
PROTECTION
Shut down o/p voltage, recovers automatically after temperature goes down
UL8750,CSA C22.2 No.250.13-12,EN61347-1,EN61347-2-13 approved, esign refer to EN60950d
92%
±2.0%
±0.5%
±1.0%
24V
14.4 ~ 24V
6.5A
156W
200mVp-p
HBG-160-24
28 ~ 34V
EMC IMMUNITY
EMC EMISSION
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH℃
92%
36V
21.6 ~ 36V
4.4A
158.4W
300mVp-p
HBG-160-36
41 ~ 47V
93.5%
60V
36 ~ 60V
2.6A
156W
300mVp-p
HBG-160-60
65 ~ 75V
HBG-160-60 A
A : IP65 rated. Output constant current level can be adjusted through internal potentiometer.
Blank : IP67 rated. Cable for I/O connection.
E : IP67 rated. Can be fixed by steel support.(option)
B : IP67 rated. output constant current lever can be adjusted through output cable with 1-10V,PWM signal and Resistance
IP65 IP67
Compliance to EN55015, EN61000-3-2 Class C ( 60% load) ; EN61000-3-3≧
Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547,light industry level (surge 4KV), criteria A
93%
48V
28.8 ~ 48V
3.3A
158.4W
300mVp-p
HBG-160-48
54 ~ 62V
CURRENT ADJ. RANGE 3.9 ~ 6.5A 2.6 ~ 4.4A 1.98 ~ 3.3A
Can be adjusted by internal potentiometer A type only
1.6 ~ 2.6A
110
SELV
FMM
Bauar
Sicherheit
egel gema
t gepruft
od
be
www.
ID 2000000000
tuv.com
wac g
os
TOTAL HARMONIC DISTORTION
THD< 20% when output loading 60% at 115VAC/230VAC input and output loading 75% at 277VAC input≧≧
MAX. No. of PSUs on 16A
CIRCUIT BREAKER 4 units (circuit breaker of type B) / 7 units (circuit breaker of type C) at 230VAC
File Name:HBG-160-SPEC 2015-05-28
Mechanical Specification Case No.211 Unit:mm
160W Single Output Switching Power Supply HBG-160 series
File Name:HBG-160-SPEC 2015-05-28
※IP67 rated. Cable for I/O connection.
Blank:(HBG-160)
※IP65 rated. Output constant current level can be adjusted through internal potentiometer.
A type:(HBG-160-_A)
B type:(HBG-160-_B)
※IP67 rated. output constant current lever can be adjusted through output cable with 1-10V,PWM signal and Resistance
※T case: Max. Case Temperature.(case temperature measured point)
※Ta: Ambient Temperature measured point
※T case: Max. Case Temperature.(case temperature measured point)
※Ta: Ambient Temperature measured point
※T case: Max. Case Temperature.(case temperature measured point)
※Ta: Ambient Temperature measured point
ψ151.68
132
132
SJTW 18AWG*3C
SJTW 18AWG*2C
4- 6.0
ψ
FG (Green/Yellow)
AC/L(Brown)
AC/N(Blue)
+V(Red)
-V(Black)
Ta
M10*P1.5-18h
Tcase
20
14.5
66.5
52.5
8.2
300±20
200±20
45°
150
13.33
13.00
ψ151.68
132
132
SJTW 18AWG*3C
SJTW 18AWG*2C
4- 6.0
ψ
FG (Green/Yellow)
AC/L(Brown)
AC/N(Blue)
+V(Red)
-V(Black)
Ta
M10*P1.5-18h
Tcase
20
14.5
66.5
52.5
8.2
300±20
200±20
45°
150
DIM+(Blue)
DIM-(White)
ψ151.68
132
132
SJTW 18AWG*3C
SJTW 18AWG*2C
4- 6.0
ψ
FG (Green/Yellow)
AC/L(Brown)
AC/N(Blue)
+V(Red)
-V(Black)
Ta
M10*P1.5-18h
Tcase
20
14.5
66.5
52.5
8.2
300±20
200±20
45°
150
SVT 18AWG*2C
300±20
160W Single Output Switching Power Supply HBG-160 series
File Name:HBG-160-SPEC 2015-05-28
E type :(HBG-160-_E)(option)
※IP67 rated. Can be fixed by steel support.
DETECTION
PWM & PFC CIRCUIT
O.L.P.O.T.P.
EMI FILTER
RECTIFIERS
POWER
SWITCHING
FILTER
&
RECTIFIERS +V
-V
I/P
FG
CONTROL
O.V.P.
&
O.C.P.
PFC
CIRCUIT
fosc : 100KHz
Block Diagram
Derating Curve Static Characteristics
INPUT VOLTAGE (V) 60Hz
90 100 125 135 145 155 165 175 180 200 230 305
100
90
80
70
60
50
40
LOAD (%)
230VAC
Input only
AMBIENT TEMPERATURE ( )℃
LOAD (%)
-40 -30 0-10 15 30 50 60 70
20
40
50
60
80
100
(HORIZONTAL)
※T case: Max. Case Temperature.(case temperature measured point)
※Ta: Ambient Temperature measured point
SJTW 18AWG*3C
FG (Green/Yellow)
AC/L(Brown)
AC/N(Blue) SJTW 18AWG*2C
+V(Red)
-V(Black)
ψ151.68
4- 6.0ψ
M10*P1.5-18h
Tcase
Ta
300±20
200±20
45°
150
132
132
20
14.5
180
66.5
52.5
8.2
150
160W Single Output Switching Power Supply HBG-160 series
File Name:HBG-160-SPEC 2015-05-28
※Using the built-in dimming function on B-type model can't turn the lighting fixture totally dark. Please refer to the connection method below to
achieve 0% brightness of the lighting fixture connecting to the LED power supply unit.
DIMMING OPERATION(for B-type only)
60KΩ
60%
60%
10KΩ
10K /NΩ20K /NΩ30K /NΩ40K /NΩ50K /NΩ60K /NΩ70K /NΩ80K /NΩ90K /NΩ
100K /NΩ
Single driver
Multiple drivers
(N=driver quantity for synchronized
dimming operation)
1V 4V 7V2V 5V 8V3V 6V 9V 10V
10%
10%
20KΩ
20%
20%
30KΩ
30%
30%
40KΩ
40%
40%
50KΩ
50%
50%
70KΩ
70%
70%
80KΩ
80%
80%
90KΩ100KΩOPEN
OPEN
OPEN
90%
90%
100%
100%
Resistance
value
Dimming value
Percentage of rated current
Percentage of rated current
※Built-in 3 in 1 dimming function, IP67 rated. Output constant current level can be adjusted through output cable by connecting a resistance or
1 ~ 10Vdc or 10V PWM signal between DIM+ and DIM-.
※Reference resistance value for output current adjustment (Typical)
※Please DO NOT connect "DIM-" to "-V".
※1 ~ 10V dimming function for output current adjustment (Typical)
60%
60%
10%
10%
20%
20%
30%
30%
40%
40%
50%
50%
70%
70%
80%
80%
90%
90%
100%
100%
Duty value
Percentage of rated current
95%~108%
-----
95%~108%
95%~108%
※10V PWM signal for output current adjustment (Typical): Frequency range :100Hz ~ 3KHz
※Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.
Using a switch and relay can turn ON/OFF the lighting fixture.
1.Output constant current level can be adjusted through output cable by connecting a or 1~10Vdc or 10V PWM signal between DIM+ and DIM-.resistance
2.The LED lighting fixture can be turned ON/OFF by the switch.
NFG L
Relay
Blue
Brown
Green/
Yellow AC/L
AC/N
HBG-160
BType
DIM+
DIM-
V(-)
V(+)
Blue
White
Black
Red
Switch Adjuster
0~100K Ohms resistance
1~10V DC Voltage
10V PWM Signal
LED Lighting Fixture
DIM+(Blue)
DIM-(White)
SJTW 18AWG*3C
SJTW 18AWG*2C
FG (Green/Yellow)
AC/L(Brown)
AC/N(Blue)
+V(Red)
-V(Black)
SVT 18AWG*2C
0.78
0.8
0.82
0.84
0.86
0.88
0.9
0.92
0.94
0.96
0.98
1
50% 60% 70% 80% 90% 100%
115V
230V
277V
74
76
78
80
82
84
86
88
90
92
94
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
115V
230V
277V
160W Single Output Switching Power Supply HBG-160 series
File Name:HBG-160-SPEC 2015-05-28
EFFICIENCY (%)
LOAD
Power Factor Characteristic
EFFICIENCY vs LOAD(48V Model)
Constant Current Mode
PF
LOAD (150W)
HBG-160 series possess superior working efficiency that up to 93% can be reached in field applications.
There are two major kinds of LED drive method "direct drive" and "with LED driver".
Typical LED power supply I-V curve
A typical LED power supply may either work in "constant voltage mode (CV) or constant current mode (CC)" to drive the LEDs.
Mean Well's LED power supply with CV+ CC characteristic can be operated at both CV mode (with LED driver, at area (A) and CC mode (direct drive, at area (B).
DRIVING METHODS OF LED MODULE
100
60
(min.)
Vo(%)
50 95 Io(%)
(A) Constant
Voltage area
(B)
Constant
Current area
(C)
Hiccup
Protection
In the constant current region, the highest voltage at the output of the driver
depends on the configuration of the end systems.
Should there be any compatibility issues, please contact MEAN WELL.
Hanger Spot Light High Bay Light Stage Light
Chain
File Name:HBG-160-SPEC 2015-05-28
INSTALLATIONS
160W Single Output Switching Power Supply HBG-160 series
Please inspect the appearance of the product for completeness if the package is damaged. There should not
be any cracks.
Please do not drop or bump the product.
All screws including the suspension screw should be paired with a spring washer and locked tight.
The entire luminaire, including the power supply should be limited to less than 10Kg.
The luminaire should be cautiously protected throughout packaging and transportation to avoid damage due to shock.
Please thoroughly perform the cautionary notes above to prevent the possibility of the luminaire falling and
injuring personnel.
Caution
