UBA2024P - NXP - Datasheet.Directory

1. General description

The UBA2024 is a family of high-voltage monolithic Integrated Compact Fluorescent

Lamp (CFL) drivers for a large range of lamp powers. Specific versions are optimized for

230 V and 110 V mains supplies. The product family integrates full CFL controller

functionality with high voltage half-bridge transistors. All products in the UBA2024 family

are pin-to-pin compatible enabling a single application design covering a wide range of

power ratings .

The IC features a soft start function, an adjustable internal oscillator and an internal drive

function with a high-voltage level shifter for driving the half-bridge.

To guarantee an accurate 50 % duty cycle, the oscillator signal is passed through a divider

before being fed to the output drivers.

2. Features and benefits

The common feature set includes:

high power efficiency

a high integration level with low component counts enablin g sm all for m fact or

electronic ballast

integrated bootstrap diode

soft start function

minimum glow time control

integrated low-voltage supply

adjustable operating frequency as a result of the embedded oscillator

an accurate 50 % duty cycle provided by an embedded oscillator signal

integrated half-bridge power transistors

an internal drive function with a high -volt age level shif ter up to 550 V (30 0 V for the

UBA2024BP and UBA2024BT)

3. Applications

Driver for any kind of half-bridge configured load up to 23 W, provided that the

maximum junction temperature is not exceeded

Designed for electronically self-ballasted CFL lamps

UBA2024

Half-bridge power IC for CFL lamps

Rev. 5 — 16 September 2010 Product data sheet

Product data sheet Rev. 5 — 16 September 2010 2 of 17

NXP Semiconductors UBA2024

Half-bridge power IC for CFL lamps

4. Ordering information

[1] For this type number, RDS(on) = 9  and ISAT = 900 mA.

[2] For this type number, RDS(on) = 6  and ISAT = 1350 mA.

[3] For this type number, RDS(on) = 6.4  and ISAT = 1200 mA.

[4] For this type number, RDS(on) = 2  and ISAT = 2500 mA.

5. Block diagram

Table 1. Ordering information

Type number Package

Name Description Version

UBA2024P[1] DIP8 plastic dual in-line package; 8 leads (300 mil) SOT97-1

UBA2024T[1] SO14 plastic small outl ine package; 14 leads; body width 3.9 mm SOT108-1

UBA2024AP[2] DIP8 plastic du al in-line package; 8 leads (300 mil) SOT97-1

UBA2024AT[3] SO14 plastic small outline package; 14 leads; body width 3.9 mm SOT108-1

UBA2024BP[4] DIP8 plastic du al in-line package; 8 leads (300 mil) SOT97-1

UBA2024BT[4] SO14 plastic small outline package; 14 leads; body width 3.9 mm SOT108-1

Fig 1. Block diagram

mdb029

SWEEP AND

GLOW TIME CONTROL HIGH VOLTAGE

LEVEL SHIFTER

VDD CONTROL

HIGH SIDE

DRIVER

LOW SIDE

DRIVER

OSCILLATOR DIVIDE-BY-2 DEAD TIME

1,2,3,5,9,10,13 (2)

7 (8)

VDD VDD(stop)

SGND

8 (1)

6* (7)**

(6) 4 HV

LS OUT

PGND

(3) 11

(5) 14

(4) 12

Product data sheet Rev. 5 — 16 September 2010 3 of 17

NXP Semiconductors UBA2024

Half-bridge power IC for CFL lamps

6. Pinning information

6.1 Pinning

6.2 Pin description

Fig 2. Pinni ng diagram SOT97-1 Fig 3. Pinning diagram SOT108-1

UBA2024P

UBA2024AP

UBA2024BP

SW RC

SGND V

FS HV

PGND OUT

014aaa657

UBA2024T

UBA2024AT

UBA2024BT

SGND OUT

SGND SGND

SGND PGND

HV FS

SGND SGND

VDD SGND

RC SW

014aaa804

7 8

Table 2. Pin description

Symbol Pin SOT97-1 Pin SOT108-1 Description

SW 1 8 sweep timing input

SGND 2 1, 2, 3, 5, 9,

10, 13 signal ground

FS 3 11 high-side floating supply output

PGND 4 12 power ground

OUT 5 14 half-bridge ou tput

HV 6 4 high-voltage supply

VDD 7 6 internal low-voltage supply output

RC 8 7 internal oscillator input

Product data sheet Rev. 5 — 16 September 2010 4 of 17

NXP Semiconductors UBA2024

Half-bridge power IC for CFL lamps

7. Functional description

7.1 Supply voltage

The UBA2024 does not require an external low-voltage supply as the mains supply

voltage a pplied to pin HV powers it. The IC derives it s own low supply voltage from this for

its internal circuitry.

7.2 Start-up state

With an increase of the supply voltage on pin HV, the IC enters the start-up state. In the

start-up state the high-side power tra n s istor is not conducting and the low-side power

transistor is switched on. The internal circuit is reset and the capacitors on the bootstrap

pin FS and low-voltage supply pin VDD are charged. Pins RC and SW are switched to

ground. The start-up state is defined until VDD = VDD(startup).

7.3 Sweep mode

The IC enters the sweep mode when the voltage on pin VDD  VDD(startup). The capa citor

on pin SW is charged b y ISW and the half-bridge circuit start s oscillating. The circuit enters

the start-up state again whe n the voltage on pin VDD VDD(stop).

The sweep time (tsweep) is determined by the charge current (Ich(sw)) and the external

capacitor (CSW). Typical the total sweep time set by CSW is:

(1)

During the sweep time the current flowing through the lamp electrodes performs some

preheating of the filaments. See Figure 5.

7.4 Reset

A DC reset circuit is incorporated in the high-side driver. The high-side transistor is

switched off when th e voltage on pin FS is be low the hig h-side lo ckout vo ltage Vfloat(UVLO).

7.5 Oscillation

The oscillation is based upon the 555-timer function. A self oscillating circuit is made with

the external re sist or ROSC and the capacitor COSC (see Figure 4).

To realize an accurate 50  duty cycle, an interna l divider is used. This reduces the bridge

frequency to half the oscillator frequency.

The output voltage of the bridge will change at the falling edge of the signal on pin RC.

The design equation for the half-bridge frequency is:

(2)

An overview of the oscillator signal, internal LS and HS drive signals and the output is

given in Figure 4.

tsweep CSW nF10.3 ms=

fosc 1

OSC

COSC



-----------------------------------------

Product data sheet Rev. 5 — 16 September 2010 5 of 17

NXP Semiconductors UBA2024

Half-bridge power IC for CFL lamps

When entering the sweep mode (VSW = 0 V), the bridge oscillator starts at 2.5 times the

nominal bridge frequency and sweeps down to the nominal frequency (bridge), set by

ROSC and COSC. During the sweep mode th e amplitude of the RC oscillator on pin RC, will

swing between Vtrip(osc)low and VSW +0.4V

trip(osc)high. The amplitude of the RC oscillator

will continue to increase until VSW +0.4V

trip(osc)high =V

trip(osc)high, this determines the end

of the sweep time. The voltage on pin SW however will continue to rise until it reaches

supply voltage level.

During this continuous decrease in frequency, the circuit approaches the resonance

frequency of the load, and this causes a high voltage across the load, which ignites the

lamp. The sweep to resonance time should be much larger than the settling time of the

supply voltage on pin HV, to guarantee that the full high-voltage is present at the moment

of ignition. See Figure 5.

Fig 4. Oscillator, drivers and output signals

time

VRC

VOUT

drive

half

bridge

time

014aaa658

Product data sheet Rev. 5 — 16 September 2010 6 of 17

NXP Semiconductors UBA2024

Half-bridge power IC for CFL lamps

7.6 Glow time control

The inherent glow time of cold-started CFL lamps reduces the switching lifetime of the

electrodes. To make th is glow phase a s shor t as possible, the maximu m power is gi ven to

the lamp during the glow time via a special control. See Figure 5.

7.7 Non-overlap time

The non-overlap time is defined as the time when both MOSFETs are not conducting. The

non-overlap time is fixed internally.

Fig 5. Start-up frequency behavior

time

minimum glow time control

tsweep

VHV

VDD

VSW

fosc

nom

Vlamp

Vign

VgloA

Vnom

VDD

0.6 Vtrip(osc)high

2.5nom

VDD(startup)

014aaa659

Product data sheet Rev. 5 — 16 September 2010 7 of 17

NXP Semiconductors UBA2024

Half-bridge power IC for CFL lamps

8. Limiting values

[1] The maximum junction temperature must not be exceeded.

[2] In accordance with the Human Body Model (HBM): equivalent to discharging a 100 pF capacitor through a 1.5 k series resistor.

Table 3. Limiting values

In accordance with the Absolute Maximum Rating System (IEC 60134).

Symbol Parameter Conditions Min Max Unit

VHV voltage on pin HV normal operation

UBA2024P - 373 V

UBA2024AP - 373 V

UBA2024T - 373 V

UBA2024AT - 373 V

UBA2024BP - 187 V

UBA2024BT - 187 V

mains transients during 0.5 s

UBA2024P - 550 V

UBA2024AP - 550 V

UBA2024T - 550 V

UBA2024AT - 550 V

UBA2024BP - 300 V

UBA2024BT - 300 V

VFS voltage on pin FS VHV VHV +14 V

VDD supply voltage low voltage; DC supply 0 14 V

IDD supply current low voltage; peak value is internally

limited; Tamb =25C05mA

VPGND voltage on pin PGND referenced to SGND 1+1V

VRC voltage on pin RC IRC 1mA 0 V

DD V

VSW voltage on pin SW ISW 1mA 0 V

DD V

SR slew rate pin OUT; repetitive 4+4V/ns

Tjjunction temperature [1] 40 +150 C

Tamb ambient temperature 40 +150 C

Tstg storage temperature 55 +150 C

VESD electrostatic discharge voltage human body model: [2]

UBA2024P: pins HV and VDD - 1000 V

UBA2024AP: pin HV - 1000 V

UBA2024T: pin HV - 1000 V

UBA2024AT: pin HV - 1000 V

UBA2024BP: pin HV - 1000 V

UBA2024BT: pin HV - 1000 V

pins SW, RC, FS, and OUT - 2500 V

machine model: [3]

pin FS - 200 V

pins HV, VDD, SW, RC, and OUT - 250 V

Product data sheet Rev. 5 — 16 September 2010 8 of 17

NXP Semiconductors UBA2024

Half-bridge power IC for CFL lamps

[3] In accordance with the Machine Model (MM): equivalent to discharging a 200 pF capacitor through a 1.5 k series resistor and a

0.75 H inductor.

9. Thermal characteristics

[1] In accordance with IEC 60747-1

10. Characteristics

Table 4. Ther mal characteristics

Symbol Parameter Conditions Typ Unit

Rth(j-a) thermal resistance from junction to ambient in free air [1]

SO14 package 95 K/W

DIP8 package 95 K/W

Rth(j-c) thermal resistance from junction to case in free air [1]

SO14 package 8 K/W

DIP8 package 16 K/W

Table 5. Chara cteristics

Tj = 25



C; all voltages are measured with respect to SGND; positive currents flow into the IC.

Symbol Parameter Conditions Min Typ Max Unit

High-voltage supply

VHV voltage on pin HV mains transients during 0.5 s; IHV  30 A

UBA2024P 0 - 550 V

UBA2024AP 0 - 550 V

UBA2024T 0 - 550 V

UBA2024AT 0 - 550 V

UBA2024BP 0 - 250 V

UBA2024BT 0 - 250 V

VFS voltage on pin FS mains transients during 0.5 s; IHV  30 A

UBA2024P 0 - 564 V

UBA2024AP 0 - 564 V

UBA2024T 0 - 564 V

UBA2024AT 0 - 564 V

UBA2024BP 0 - 264 V

UBA2024BT 0 - 264 V

Low-voltage supply

VDD supply voltage VHV =100V; R

osc =; VSW =V

DD;

VRC =0V 11.7 12.5 13.3 V

Start-up state

IHV current on pin HV VHV =100V; R

osc =; VSW =V

DD;

VRC =0V --0.39mA

VDD(startup) start-up supply voltage 10 11 12 V

VDD(stop) stop supply voltage 8 8.5 9 V

VDD(hys) hysteresis of supply voltage 2 2.5 3 V

Product data sheet Rev. 5 — 16 September 2010 9 of 17

NXP Semiconductors UBA2024

Half-bridge power IC for CFL lamps

Output stage

Ron on-state resistance HS transistor; VHV =310V; I

D= 100 mA

UBA2024P - 9.7 11 

UBA2024T - 9.7 11 

UBA2024AP - 6.5 7.4 

UBA2024AT - 7.0 8.0 

HS transistor; VHV =160V; I

D= 100 mA

UBA2024BP - 2.0 2.35 

UBA2024BT - 2.0 2.35 

LS transistor; ID= 100 mA

UBA2024P - 8.5 9.4 

UBA2024T - 8.5 9.4 

UBA2024AP - 5.7 6.3 

UBA2024AT - 6.2 6.9 

UBA2024BP - 2.3 2.55 

UBA2024BT - 2.3 2.55 

VFforward voltage HS; IF= 200 mA - - 2.2 V

LS; IF= 200 mA - - 2.0 V

bootstrap diode; IF=1mA 0.7 1.0 1.3 V

IDsat drain saturation current HS; VDS =30V; T

j 125 C; VHV =310V

UBA2024P 900 - - mA

UBA2024AP 1350 - - mA

UBA2024T 900 - - mA

UBA2024AT 1200 - - mA

HS; VDS =30V; T

j 125 C; VHV =160V

UBA2024BP 2500 - - mA

UBA2024BT 2500 - - mA

LS; VDS =30V; T

j125 C

UBA2024P 900 - - mA

UBA2024AP 1350 - - mA

UBA2024T 900 - - mA

UBA2024AT 1200 - - mA

UBA2024BP 2500 - - mA

UBA2024BT 2500 - - mA

tno non-overlap time 1 1.35 1.7 s

Vfloat(UVLO) undervoltage lockout

floating voltage 3.6 4.2 4.8 V

Table 5. Chara cteristics …continued

Tj = 25



C; all voltages are measured with respect to SGND; positive currents flow into the IC.

Symbol Parameter Conditions Min Typ Max Unit

Product data sheet Rev. 5 — 16 September 2010 10 of 17

NXP Semiconductors UBA2024

Half-bridge power IC for CFL lamps

IFS current on pin FS VHV =310V; V

FS = 12.2 V

UBA2024P, UBA2024T 10 14 18 A

UBA2024AP, UBA2024AT 10 14 18 A

VHV =160V; V

FS = 12.2 V

UBA2024BP, UBA2024BT 10 14 18 A

Internal oscillator

fosc oscillator frequency VSW = 0 V - 150 - kHz

VSW =V

DD - - 60 kHz

operating; nominal; ROSC =100k;

COSC = 220 pF; VSW =V

40.05 41.32 42.68 kHz

fosc/fosc relative oscillator frequency

variation ROSC = 100 k; COSC =220pF;

20 CTj+150 C-2-%

kHhigh-level trip point factor 0.382 0.395 0.408

Vtrip(osc)hig

high oscillator trip voltage Vtrip(osc)high =k

HVDD 4.58 4.94 5.29 V

kLlow-level trip point factor 0.030 0.033 0.036

Vtrip(osc)low low oscillator trip voltage Vtrip(osc)low =k

LVDD 0.367 0.413 0.458 V

Kosc oscillator constant ROSC = 100 k; COSC = 220 pF 1.065 1.1 1.35 V

Sweep function

Ich(sweep) sweep charge current VSW = 0 V 215 280 345 nA

tsweep sweep time CSW =33nF; V

DD = 12.2 V 0.28 0.35 0.45 s

Table 5. Chara cteristics …continued

Tj = 25



C; all voltages are measured with respect to SGND; positive currents flow into the IC.

Symbol Parameter Conditions Min Typ Max Unit

Product data sheet Rev. 5 — 16 September 2010 11 of 17

NXP Semiconductors UBA2024

Half-bridge power IC for CFL lamps

11. Application information

Fig 6. Schematic of 230 V standard compact fluorescent lamp application using UBA2024

mdb033

CBUF

4.7 uF

LFILT

1.8 mH

RFUS

33 Ω

CHB2

47 nF

11 W/150 mA

max. 550 V

3.1 mH

LLA

CHB1

47 nF

ROSC

110 K

COSC

180 pF

CFS

10 nF

CDV

100 pF

CVDD

10 nF

CLA

1.5 nF

UBA2024

VDD

SGND

OUT

PGND

CSW

33 nF

AC mains

supply

(230 V)

Fig 7. Schematic of 120 V standard compact fluorescent lamp application using UBA2024B

001aam620

ROSC

26.1 kΩ

CSW

470 nF RSW

4.7 MΩ

COSC

1.2 nF

CFS

10 nF

CDVDT

820 pF

CHB1

150 nF

CBUS

33 μF

RFUS

4.7 Ω

CHB2

150 nF

0.66 mH

LFILT maximum 300 V

1.5 mH

CVDD

10 nF

CRS

24 W/300 mA

10 nF

UBA2024B

PGND

OUT

HV VDD

SGND

AC mains

supply

(120 V) CFL

Product data sheet Rev. 5 — 16 September 2010 12 of 17

NXP Semiconductors UBA2024

Half-bridge power IC for CFL lamps

12. Package outline

Fig 8. Package outline SOT97-1 (DIP8)

REFERENCES

OUTLINE

VERSION EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC JEITA

SOT97-1 99-12-27

03-02-13

UNIT A

max. 12 b1(1) (1) (1)

b2cD E e M Z

DIMENSIONS (inch dimensions are derived from the original mm dimensions)

min. A

max. bmax.

1.73

1.14 0.53

0.38 0.36

0.23 9.8

9.2 6.48

6.20 3.60

3.05 0.2542.54 7.62 8.25

7.80 10.0

8.3 1.154.2 0.51 3.2

inches 0.068

0.045 0.021

0.015 0.014

0.009

1.07

0.89

0.042

0.035 0.39

0.36 0.26

0.24 0.14

0.12 0.010.1 0.3 0.32

0.31 0.39

0.33 0.0450.17 0.02 0.13

050G01 MO-001 SC-504-8

(e )

seating plane

0 5 10 mm

scale

Note

1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included.

pin 1 index

DIP8: plastic dual in-line package; 8 leads (300 mil) SOT97-1

Product data sheet Rev. 5 — 16 September 2010 13 of 17

NXP Semiconductors UBA2024

Half-bridge power IC for CFL lamps

Fig 9. Package outline SOT108-1 (SO14)

UNIT A

max. A1A2A3bpcD

(1) E(1) (1)

ELL

pQZywv θ

REFERENCES

OUTLINE

VERSION EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC JEITA

inches

1.75 0.25

0.10 1.45

1.25 0.25 0.49

0.36 0.25

0.19 8.75

8.55 4.0

3.8 1.27 6.2

5.8 0.7

0.6 0.7

0.3 8

0.25 0.1

DIMENSIONS (inch dimensions are derived from the original mm dimensions)

Note

1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included.

1.0

0.4

SOT108-1

detail X

vMA

(A )

076E06 MS-012

pin 1 index

0.069 0.010

0.004 0.057

0.049 0.01 0.019

0.014 0.0100

0.0075 0.35

0.34 0.16

0.15 0.05

1.05

0.041

0.244

0.228 0.028

0.024 0.028

0.012

0.01

0.25

0.01 0.004

0.039

0.016

99-12-27

03-02-19

0 2.5 5 mm

scale

SO14: plastic small outline package; 14 leads; body width 3.9 mm SOT108-1

Product data sheet Rev. 5 — 16 September 2010 14 of 17

NXP Semiconductors UBA2024

Half-bridge power IC for CFL lamps

13. Revision history

Table 6. Revision history

Document ID Release date Data sheet status Change notice Supersedes

UBA2024 v.5 20100916 Product data sheet - UBA2024_4

Modifications: •Latest NXP template applied.

•Legal page updated.

•UBA2024BP and UBA2024BT added to Table 1 “Ordering information”.

•Section 1 “General description” and Section 2 “Features and benefits” updated.

•Section 8 “Limiting values” and Section 10 “Characteristics” updated.

•Application information updated.

•Figure 7 “Schematic of 120 V standard compact fluorescent lamp application using

UBA2024B” added.

UBA2024_4 20090917 Product data sheet - UBA2024_3

UBA2024_3 081016 Product data sheet - UBA2024_2

UBA2024_2 040203 Product data sheet - UBA2024_1

UBA2024_1 030813 Product data sheet - -

Product data sheet Rev. 5 — 16 September 2010 15 of 17

NXP Semiconductors UBA2024

Half-bridge power IC for CFL lamps

14. Legal information

14.1 Data sheet status

[1] Please consult the most recently issued document before initiating or completing a design.

[2] The term ‘short data sheet’ is explained in section “Definitions”.

[3] The product status of de vice(s) descr ibed in th is docume nt may have cha nged since this docume nt was publis hed and ma y dif fer in case of multiple devices. The latest product status

information is available on the Internet at URL http://www.nxp.com.

14.2 Definitions

Draft — The document is a draft version only. The content is still under

internal review and subject to formal approval, which may result in

modifications or additions. NXP Semiconductors does not give any

representations or warranties as to the accuracy or completeness of

information included herein and shall have no liab ility for the consequences of

use of such information.

Short data sheet — A short data sheet is an extract from a full data sheet

with the same product type number(s) and tit le. A short data sh eet is intended

for quick reference only and shou ld not be rel ied u pon to cont ain det ailed and

full information. For detailed and full information see the relevant full data

sheet, which is available on request via the local NXP Semiconductors sales

office. In case of any inconsistency or conflict with the short data sheet, the

full data sheet shall pre vail.

Product specificatio n — The information and data provided in a Product

data sheet shall define the specification of the product as agreed between

NXP Semiconductors and its customer, unless NXP Semiconductors and

customer have explicitly agreed otherwise in writing. In no event however,

shall an agreement be valid in which the NXP Semiconductors product is

deemed to off er functions and qualities beyond those described in the

Product data sheet.

14.3 Disclaimers

Limited warr a nty and liability — Information in this document is believed to

be accurate and reliable. However, NXP Semiconductors does not give any

representations or warranties, expressed or implied, as to the accuracy or

completeness of such information and shall have no liability for the

consequences of use of such information.

In no event shall NXP Semiconductors be liable for any indirect, incidental,

punitive, special or consequ ential damages (including - wit hout limitatio n - lost

profits, lost savings, business interruption, costs related to the removal or

replacement of any products or rework charges) whether or not such

damages are based on tort (including negligence), warranty, breach of

contract or any other legal theory.

Notwithstanding any damages that customer might incur for any reason

whatsoever, NXP Semiconductors’ aggregat e and cumulative liabil ity towards

customer for the products described herein shall be limited in accordance

with the Terms and conditions of commercial sale of NXP Semiconductors.

Right to make changes — NXP Semiconductors reserves the right to make

changes to information published in this document, including without

limitation specifications and product descriptions, at any time and without

notice. This document supersedes and replaces all informa tion supplied prior

to the publication hereof .

Suitability for use — NXP Semiconductors products are not designed,

authorized or warranted to be suit able for use in life support, life-critical or

safety-critical systems or equipment, nor in applications where failure or

malfunction of an NXP Semiconductors product can reaso nably be expected

to result in perso nal injury, death or severe property or environme ntal

damage. NXP Semiconductors accepts no liab ility for inclusion and/or use of

NXP Semiconductors products in such equipment or applications and

therefore such inclusion and/or use is at the customer’s own risk.

Applications — Applications that are described herein for any of these

products are for illustrative purposes only. NXP Semiconductors makes no

representation or warranty tha t such application s will be suitable for the

specified use without further testing or modification.

Customers are responsible for the design and ope ration of their applications

and products using NXP Semiconductors product s, and NXP Semiconductors

accepts no liability for any assistance with applications or customer product

design. It is customer’s sole responsibility to determine whether the NXP

Semiconductors product is suit able and fit for the custome r’s applications and

products planned, as well as fo r the planned application and use of

customer’s third party customer(s). Customers should provide appropriate

design and operating safeguards to minimize the risks associated with their

applications and products.

NXP Semiconductors does not accept any liability related to any default,

damage, costs or problem which is based on any weakness or default in the

customer’s applications or products, or the applicatio n or use by custo mer’s

third party customer(s). Customer is responsible for doing all necessary

testing for th e customer’s applications and products using NXP

Semiconductors products in order to avoid a default of the applications and

the products or of the application or use by customer’s third party

customer(s). NXP does not accept any liability in this respect.

Limiting values — Stress above one or more limiting values (as defined in

the Absolute Maximum Ratings System of IEC 60134) will cause permanent

damage to the device. Limiting values are stress ratings only and (proper)

operation of the device at these or any other conditions above those given in

the Recommended operating conditions section (if present) or the

Characteristics sections of this document is not warranted. Constant or

repeated exposure to limiting values will permanent ly and irreversibly affect

the quality and reliability of the device.

Terms and conditions of commercial sale — NXP Semiconductors

products are sold subject to the general terms and conditions of commercial

sale, as published at http://www.nxp.com/profile/terms, unless otherwise

agreed in a valid written individua l agreement. In case an individual

agreement is concluded only the ter ms and conditions of the respective

agreement shall apply. NXP Semiconductors hereby exp ressly objects to

applying the customer’s general terms and conditions with regard to the

purchase of NXP Semiconductors products by customer.

No offer to sell or license — Nothing i n this document may be interpreted or

construed as an of fer t o sell product s that is open for accept ance or t he grant,

conveyance or implication of any license under any copyrights, patents or

other industrial or intellectual property rights.

Export control — This document as well as the item(s) described herein

may be subject to export control regulatio ns. Export might require a prior

authorization from national authorities.

Document status[1][2] Product status[3] Definition

Objective [short] data sheet Development This document contains data from the objective specification for product development.

Preliminary [short] dat a sheet Qualification This document contains data from the preliminary specification.

Product [short] dat a sheet Producti on This document contains the product specification.

Product data sheet Rev. 5 — 16 September 2010 16 of 17

NXP Semiconductors UBA2024

Half-bridge power IC for CFL lamps

Non-automotive qualified products — Unless this data sheet expressly

states that this specific NXP Semiconductors product is automotive qualified,

the product is not suitable for automo tive use. It i s neit her qua lif ied nor test ed

in accordance with automotive testing or application requirements. NXP

Semiconductors accepts no liability for inclusion and/or use of

non-automotive qualified products in automotive equipment or applications.

In the event that customer uses the product for design-in and use in

automotive applications to automot ive specifications and standard s, customer

(a) shall use the product without NXP Semiconductors’ warranty of the

product for such automotive applications, use and specifications, and (b)

whenever customer uses the product for automotive applications beyond

NXP Semiconductors’ specifications such use shall be solely at customer’s

own risk, and (c) customer fully indemnifies NXP Semiconductors for any

liability, damages or failed product cl aims resulting from custome r design and

use of the product for automotive applications beyond NXP Semiconductors’

standard warranty and NXP Semiconductors’ product specifications.

14.4 Trademarks

Notice: All referenced b rands, produc t names, service names and trademarks

are the property of their respect i ve ow ners.

15. Contact information

For more information, please visit: http://www.nxp.com

For sales office addresses, please send an email to: salesaddresses@nxp.com

NXP Semiconductors UBA2024

Half-bridge power IC for CFL lamps

For more information, please visit: http://www.nxp.co m

For sales office addresses, please send an email to: salesaddresses@nxp.com

Date of release: 16 September 2010

Document identifier: UBA2024

Please be aware that important notices concerning this document and the product(s)

described herein, have been included in section ‘Legal information’.

16. Contents

1 General description. . . . . . . . . . . . . . . . . . . . . . 1

2 Features and benefits . . . . . . . . . . . . . . . . . . . . 1

3 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

4 Ordering information. . . . . . . . . . . . . . . . . . . . . 2

5 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 2

6 Pinning information. . . . . . . . . . . . . . . . . . . . . . 3

6.1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

6.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3

7 Functional description . . . . . . . . . . . . . . . . . . . 4

7.1 Supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . 4

7.2 Start-up state . . . . . . . . . . . . . . . . . . . . . . . . . . 4

7.3 Sweep mode. . . . . . . . . . . . . . . . . . . . . . . . . . . 4

7.4 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

7.5 Oscillation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

7.6 Glow time control. . . . . . . . . . . . . . . . . . . . . . . 6

7.7 Non-overlap time . . . . . . . . . . . . . . . . . . . . . . . 6

8 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 7

9 Thermal characteristics . . . . . . . . . . . . . . . . . . 8

10 Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . 8

11 Application information. . . . . . . . . . . . . . . . . . 11

12 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 12

13 Revision history. . . . . . . . . . . . . . . . . . . . . . . . 14

14 Legal information. . . . . . . . . . . . . . . . . . . . . . . 15

14.1 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 15

14.2 Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

14.3 Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . 15

14.4 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 16

15 Contact information. . . . . . . . . . . . . . . . . . . . . 16

16 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17