LTC3858 Low IQ, Dual 2-Phase Synchronous Step-Down Controller DESCRIPTION FEATURES n n n n n n n n n n n n n n n n n n The LTC(R)3858 is a high performance dual step-down switching regulator controller that drives all N-channel synchronous power MOSFET stages. A constant frequency current mode architecture allows a phase-lockable frequency of up to 850kHz. Power loss and noise due to the input capacitor ESR are minimized by operating the two controller outputs out of phase. Low Operating IQ: 170A (One Channel On) Wide Output Voltage Range: 0.8V VOUT 24V Wide VIN Range: 4V to 38V RSENSE or DCR Current Sensing Out-of-Phase Controllers Reduce Required Input Capacitance and Power Supply Induced Noise OPTI-LOOP(R) Compensation Minimizes COUT Phase-Lockable Frequency (75kHz-850kHz) Programmable Fixed Frequency (50kHz-900kHz) Selectable Continuous, Pulse-Skipping or Burst Mode(R) Operation at Light Loads Very Low Dropout Operation: 99% Duty Cycle Adjustable Output Voltage Soft-Start Power Good Output Voltage Monitor Output Overvoltage Protection Output Latch-Off Protection During Short Circuit Low Shutdown IQ: 8A Internal LDO Powers Gate Drive from VIN or EXTVCC No Current Foldback During Start-Up Small 5mm x 5mm QFN Package The 170A no-load quiescent current extends operating life in battery-powered systems. OPTI-LOOP compensation allows the transient response to be optimized over a wide range of output capacitance and ESR values. The LTC3858 features a precision 0.8V reference and a power good output indicator. A wide 4V to 38V input supply range encompasses a wide range of intermediate bus voltages and battery chemistries. Independent soft-start pins for each controller ramp the output voltages during start-up. The output latch-off feature protects the circuit in short-circuit conditions. For a leaded 28-lead SSOP package with a fixed current limit and one PGOOD output, without phase modulation or a clock output, see the LTC3858-1 data sheet. APPLICATIONS n n n Automotive Systems Battery Operated Digital Devices Distributed DC Power Systems L, LT, LTC, LTM, Burst Mode, OPTI-LOOP, Module, PolyPhase, Linear Technology and the Linear logo are registered trademarks and No RSENSE and UltraFast are trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents, including 5481178, 5705919, 5929620, 6100678, 6144194, 6177787, 6304066, 6580258. TYPICAL APPLICATION High Efficiency Dual 8.5V/3.3V Step-Down Converter 22F 50V 4.7F VIN INTVCC TG1 BOOST1 3.3H BOOST2 90 0.1F BG1 BG2 LTC3858 SENSE1+ PGND SENSE2+ SENSE2- VFB2 ITH2 SENSE1- VFB1 ITH1 62.5k 150F 680pF 20k 15k SS1 0.1F SGND 193k 680pF SS2 0.1F 20k 1000 EFFICIENCY 70 100 60 POWER LOSS 50 10 40 30 0.01 0.007 VOUT1 3.3V 5A 80 7.2H SW2 VOUT2 8.5V 3.5A 150F 15k 20 VIN = 12V VOUT = 3.3V FIGURE 12 CIRCUIT 10 0 0.0001 0.001 0.01 0.1 1 OUTPUT CURRENT (A) POWER LOSS (mW) SW1 10000 100 TG2 EFFICIENCY (%) 0.1F Efficiency and Power Loss vs Load Current VIN 9V TO 38V 1 0.1 10 3858 TA01b 3858 TA01 3858fc 1 LTC3858 ABSOLUTE MAXIMUM RATINGS PIN CONFIGURATION (Note 1) Input Supply Voltage (VIN) ......................... -0.3V to 40V Topside Driver Voltages BOOST1, BOOST2 ................................. -0.3V to 46V Switch Voltage (SW1, SW2) ........................ -5V to 40V PLLIN/MODE,(BOOST1-SW1), (BOOST2-SW2) ........................................... -0.3V to 6V RUN1, RUN2 ............................................... -0.3V to 8V Maximum Current Sourced into Pin from Source >8V...............................................100A SENSE1+, SENSE2+, SENSE1- SENSE2- Voltages...................................... -0.3V to 28V FREQ Voltages ..................................... -0.3V to INTVCC ILIM, PHASMD Voltages ....................... -0.3V to INTVCC EXTVCC ...................................................... -0.3V to 14V ITH1, ITH2,VFB1, VFB2 Voltages ...................... -0.3V to 6V PGOOD1, PGOOD2 Voltages ....................... -0.3V to 6V SS1, SS2, INTVCC Voltages ......................... -0.3V to 6V Operating Junction Temperature Range (Note 2).................................................. -40C to 125C Maximum Junction Temperature (Note 3) ............ 125C Storage Temperature Range................... -65C to 150C SW1 TG1 PGOOD1 ILIM SS1 ITH1 VFB1 SENSE1+ TOP VIEW 32 31 30 29 28 27 26 25 SENSE1- 1 24 BOOST1 FREQ 2 23 BG1 PHASMD 3 22 VIN CLKOUT 4 21 PGND 33 SGND PLLIN/MODE 5 20 EXTVCC SGND 6 19 INTVCC RUN1 7 18 BG2 17 BOOST2 RUN2 8 SW2 TG2 PGOOD2 SS2 ITH2 VFB2 SENSE2+ SENSE2- 9 10 11 12 13 14 15 16 UH PACKAGE 32-LEAD (5mm s 5mm) PLASTIC QFN TJMAX = 125C, JA = 34C/W EXPOSED PAD (PIN 33) IS SGND, MUST BE SOLDERED TO PCB ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC3858EUH#PBF LTC3858EUH#TRPBF 3858 32-Lead (5mm x 5mm) Plastic QFN -40C to 125C LTC3858IUH#PBF LTC3858IUH#TRPBF 3858 32-Lead (5mm x 5mm) Plastic QFN -40C to 125C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at TA = 25C (Note 2). VIN = 12V, VRUN1,2 = 5V, EXTVCC = 0V unless otherwise noted. SYMBOL PARAMETER VIN Input Supply Operating Voltage Range VFB1,2 Regulated Feedback Voltage CONDITIONS MIN TYP 4 (Note 4) ITH1,2 = 1.2V -40C to 125C -40C to 85C IFB1,2 Feedback Current (Note 4) VREFLNREG Reference Voltage Line Regulation (Note 4) VIN = 4.5V to 38V l 0.788 0.792 MAX UNITS 38 V 0.800 0.800 0.812 0.808 V V 5 50 nA 0.002 0.02 %/V 3858fc 2 LTC3858 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at TA = 25C (Note 2). VIN = 12V, VRUN1,2 = 5V, EXTVCC = 0V unless otherwise noted. SYMBOL PARAMETER CONDITIONS VLOADREG Output Voltage Load Regulation (Note4) Measured in Servo Loop, ITH Voltage = 1.2V to 0.7V (Note4) Measured in Servo Loop, ITH Voltage = 1.2V to 2V MIN TYP MAX l 0.01 0.1 % l -0.01 -0.1 % gm1,2 Transconductance Amplifier gm (Note 4) ITH1,2 = 1.2V, Sink/Source = 5A IQ Input DC Supply Current (Note 5) Pulse Skip or Forced Continuous Mode (One Channel On) RUN1 = 5V and RUN2 = 0V, VFB1 = 0.83V (No Load) or RUN1 = 0V and RUN2 = 5V, VFB2 = 0.83V (No Load) Pulse Skip or Forced Continuous Mode (Both Channels On) RUN1,2 = 5V, VFB1,2 = 0.83V (No Load) Sleep Mode (One Channel On) RUN1 = 5V and RUN2 = 0V, VFB1 = 0.83V (No Load) or RUN1 = 0V and RUN2 = 5V, VFB2 = 0.83V (No Load) 170 250 A Sleep Mode (Both Channels On) RUN1,2 = 5V, VFB1,2 = 0.83V (No Load) 300 450 A Shutdown RUN1,2 = 0V Undervoltage Lockout INTVCC Ramping Up INTVCC Ramping Down UVLO VOVL Feedback Overvoltage Protection Measured at VFB1,2, Relative to Regulated VFB1,2 ISENSE+ SENSE+ Pin Current Each Channel ISENSE- SENSE- Pin Current Each Channel VOUT1,2 < INTVCC - 0.5V VOUT1,2 > INTVCC + 0.5V 2 UNITS l l mmho 1.3 mA 2 mA 8 20 A 3.6 4.0 3.8 4.2 4 V V 7 10 13 % 1 A 1 950 A A 550 DFMAX Maximum Duty Factor In Dropout, FREQ = 0V 98 99.4 ISS1,2 Soft-Start Charge Current VSS1,2 = 0V 0.7 1.0 1.4 VRUN1,2 On RUN Pin On Threshold Voltage VRUN1, VRUN2 Rising 1.23 1.28 1.33 l VRUN1,2 Hyst RUN Pin Hysteresis Voltage % 50 A V mV VSS1,2 LA SS Pin Latch-Off Arming Threshold Voltage VSS1, VSS2 Rising from 1V 1.9 2 2.1 V VSS1,2 LT SS Pin Latch-Off Threshold Voltage VSS1, VSS2 Falling from 2V 1.3 1.5 1.7 V IDSC1,2 LT SS Discharge Current Short-Circuit Condition VFB1,2 = 0V, VSS1,2 = 5V 7 10 13 A VSENSE(MAX) Maximum Current Sense Threshold Voltage VFB1,2 = 0.7V, VSENSE1-,2- = 3.3V, ILIM = 0 VFB1,2 = 0.7V, VSENSE1-,2- = 3.3V, ILIM = FLOAT VFB1,2 = 0.7V, VSENSE1-,2- = 3.3V, ILIM = INTVCC 22 43 64 30 50 75 36 57 86 mV mV mV l l l Gate Driver TG1,2 Pull-Up On-Resistance Pull-Down On-Resistance 2.5 1.5 BG1,2 Pull-Up On-Resistance Pull-Down On-Resistance 2.4 1.1 TG1,2 tr TG1,2 tf TG Transistion Time: Rise Time Fall Time (Note 6) CLOAD = 3300pF CLOAD = 3300pF 25 16 ns ns BG1,2 tr BG1,2 tf BG Transistion Time: Rise Time Fall Time (Note 6) CLOAD = 3300pF CLOAD = 3300pF 28 13 ns ns Top Gate Off to Bottom Gate On Delay Synchronous Switch-On Delay Time CLOAD = 3300pF Each Driver 30 ns TG/BG t1D 3858fc 3 LTC3858 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at TA = 25C (Note 2). VIN = 12V, VRUN1,2 = 5V, EXTVCC = 0V unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS BG/TG t1D Bottom Gate Off to Top Gate On Delay Top Switch-On Delay Time CLOAD = 3300pF Each Driver 30 ns tON(MIN) Minimum On-Time (Note 7) 95 ns INTVCC Linear Regulator VINTVCCVIN Internal VCC Voltage 6V < VIN < 38V, VEXTVCC = 0V VLDOVIN INTVCC Load Regulation ICC = 0mA to 50mA, VEXTVCC = 0V VINTVCCEXT Internal VCC Voltage 6V < VEXTVCC < 13V VLDOEXT INTVCC Load Regulation ICC = 0mA to 50mA, VEXTVCC = 8.5V VEXTVCC EXTVCC Switchover Voltage EXTVCC Ramping Positive VLDOHYS EXTVCC Hysteresis Voltage 4.85 4.85 4.5 5.1 5.35 V 0.7 1.1 % 5.1 5.35 V 0.6 1.1 % 4.7 4.9 V 250 mV 105 kHz Oscillator and Phase-Locked Loop f25k Programmable Frequency RFREQ = 25k, PLLIN/MODE = DC Voltage f65k Programmable Frequency RFREQ = 65k, PLLIN/MODE = DC Voltage f105k Programmable Frequency RFREQ = 105k, PLLIN/MODE = DC Voltage fLOW Low Fixed Frequency VFREQ = 0V, PLLIN/MODE = DC Voltage fHIGH High Fixed Frequency VFREQ = INTVCC, PLLIN/MODE = DC Voltage fSYNC Synchronizable Frequency PLLIN/MODE = External Clock 375 440 505 835 l 320 350 485 535 75 kHz kHz 380 kHz 585 kHz 850 kHz PGOOD1 and PGOOD2 Outputs VPGL PGOOD Voltage Low IPGOOD = 2mA IPGOOD PGOOD Leakage Current VPGOOD = 5V VPG PGOOD Trip Level VFB with Respect to Set Regulated Voltage VFB Ramping Negative Hysteresis -13 VFB with Respect to Set Regulated Voltage VFB Ramping Positive Hysteresis 7 tPG Delay for Reporting a Fault (PGOOD Low) Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Ratings for extended periods may affect device reliability and lifetime. Note 2: The LTC3858 is tested under pulsed conditions such that TJ TA. The LTC3858E is guaranteed to meet performance specifications from 0C to 85C. Specifications over the -40C to 125C operating junction temperature range are assured by design, characterization and correlation with statistical process controls. The LTC3858I is guaranteed over the full -40C to 125C operating junction temperature range. Note that the maximum ambient temperature is determined by specific operating conditions in conjunction with board layout, the rated package thermal resistance and other environmental factors. 0.2 0.4 V 1 A -10 2.5 -7 % % 10 2.5 13 % % 25 s Note 3: TJ is calculated from the ambient temperature TA and power dissipation PD according to the following formula: TJ = TA + (PD * 34C/W) Note 4: The LTC3858 is tested in a feedback loop that servos VITH1,2 to a specified voltage and measures the resultant VFB1,2. The specification at 85C is not tested in production. This specification is assured by design, characterization and correlation to production testing at 125C. Note 5: Dynamic supply current is higher due to the gate charge being delivered at the switching frequency. See Applications information. Note 6: Rise and fall times are measured using 10% and 90% levels. Delay times are measured using 50% levels Note 7: The minimum on-time condition is specified for an inductor peak-to-peak ripple current of 40% IMAX (See Minimum On-Time Considerations in the Applications Information section). 3858fc 4 LTC3858 TYPICAL PERFORMANCE CHARACTERISTICS Efficiency and Power Loss vs Output Current Efficiency vs Output Current 100 90 100 60 30 20 10 0 0.0001 Burst Mode OPERATION 10 PULSESKIPPING MODE 1 FORCED CONTINUOUS MODE 0.1 0.001 0.01 0.1 1 10 OUTPUT CURRENT (A) EFFICIENCY (%) 70 40 80 1000 POWER LOSS (mW) EFFICIENCY (%) FIGURE 12 CIRCUIT 90 VIN = 12V VOUT = 3.3V 80 50 100 10000 VIN = 5V 70 VIN = 12V 60 50 40 30 20 10 0 0.0001 VOUT = 3.3V FIGURE 12 CIRCUIT 0.001 0.01 0.1 1 OUTPUT CURRENT (A) 3858 G02 3858 G01 Efficiency vs Input Voltage 98 EFFICIENCY (%) 94 Load Step (Forced Continuous Mode) Load Step (Burst Mode Operation) FIGURE 12 CIRCUIT VOUT = 3.3V IOUT = 4A 96 VOUT 100mV/DIV ACCOUPLED 92 10 VOUT 100mV/DIV ACCOUPLED 90 88 IL 2A/DIV 86 IL 2A/DIV 84 82 80 0 5 10 15 20 25 30 INPUT VOLTAGE (V) 35 40 VOUT = 3.3V 20s/DIV FIGURE 12 CIRCUIT 3858 G04 20s/DIV VOUT = 3.3V FIGURE 12 CIRCUIT 3858 G05 3858 G03 Load Step (Pulse-Skipping Mode) VOUT 100mV/DIV ACCOUPLED IL 2A/DIV Inductor Current at Light Load Soft-Start FORCED CONTINUOUS MODE VOUT2 2V/DIV Burst Mode OPERATION 2A/DIV VOUT1 2V/DIV PULSESKIPPING MODE 20s/DIV VOUT = 3.3V FIGURE 12 CIRCUIT 3858 G06 VOUT = 3.3V 2s/DIV ILOAD = 200A FIGURE 12 CIRCUIT 3858 G07 20ms/DIV FIGURE 12 CIRCUIT 3858 G08 3858fc 5 LTC3858 TYPICAL PERFORMANCE CHARACTERISTICS Total Input Supply Current vs Input Voltage 300A LOAD 250 200 NO LOAD 150 100 50 0 5 10 30 25 20 INPUT VOLTAGE (V) 15 35 5.4 5.2 INTVCC 5.0 EXTVCC RISING 4.8 EXTVCC FALLING 4.6 5.0 80 55 30 TEMPERATURE (C) 5 3858 G10 ILIM = GND ILIM = FLOAT ILIM = INTVCC -20 -150 -200 -250 -300 -350 -400 -450 -500 5% DUTY CYCLE -40 0 0.2 0.4 0.6 0.8 1.0 ITH PIN VOLTAGE 1.2 -550 -600 1.4 0 210 60 ILIM = FLOAT 50 40 ILIM = GND 30 60 ILIM = FLOAT 40 ILIM = GND 20 20 0 10 20 30 40 50 60 70 80 90 100 DUTY CYCLE (%) Shutdown Current vs Temperature Quiescent Current vs Temperature ILIM = INTVCC 40 3858 G15 230 QUIESCENT CURRENT (A) MAXIMUM CURRENT SENSE VOLTAGE (mV) Foldback Current Limit 35 ILIM = INTVCC 3858 G14 90 70 15 20 25 30 INPUT VOLTAGE (V) 80 0 25 10 15 20 VSENSE COMMON MODE VOLTAGE (V) 5 3858 G13 80 10 3858 G12 MAXIMUM CURRENT SENSE VOLTAGE (mV) -100 SENSE- CURRENT (A) CURRENT SENSE THRESHOLD (mV) -50 20 5 Maximum Current Sense Threshold vs Duty Cycle 0 PULSE SKIPPING FORCED CONTINUOUS Burst Mode OPERATION (FALLING) Burst Mode OPERATION (RISING) 0 0 130 SENSE- Pin Input Bias Current 80 40 105 3858 G11 Maximum Current Sense Voltage vs ITH Voltage 60 5.1 4.2 4.0 -45 -20 40 5.2 5.1 4.4 10 PLLIN/MODE = 0 VIN = 12V VOUT = 3.3V ONE CHANNEL ON SHUTDOWN CURRENT (A) SUPPLY CURRENT (A) 300 5.2 INTVCC VOLTAGE (V) FIGURE 12 CIRCUIT VOUT = 3.3V ONE CHANNEL ON 350 INTVCC Line Regulation 5.6 EXTVCC AND INTVCC VOLTAGE (V) 400 EXTVCC Switchover and INTVCC Voltages vs Temperature 190 170 150 130 9 8 7 6 5 10 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 FEEDBACK VOLTAGE (V) 3858 G16 110 -45 -20 80 5 55 30 TEMPERATURE (C) 105 130 3858 G17 4 -45 -20 55 30 80 5 TEMPERATURE (C) 105 130 3858 G18 3858fc 6 LTC3858 TYPICAL PERFORMANCE CHARACTERISTICS Soft-Start Pull-Up Current vs Temperature 1.40 808 REGULATED FEEDBACK VOLTAGE (mV) 1.20 1.35 1.15 1.30 1.10 RUN PIN VOLTAGE (V) SS PULL-UP CURRENT (A) Regulated Feedback Voltage vs Temperature Shutdown (RUN) Threshold vs Temperature 1.05 1.00 0.95 0.90 1.25 1.20 1.15 1.10 1.05 1.00 0.85 0.95 0.80 -45 -20 80 55 30 TEMPERATURE (C) 5 105 0.90 -45 130 -20 55 30 5 80 TEMPERATURE (C) 105 800 798 796 794 792 -45 -20 130 12 700 600 10 FREQUENCY (kHz) INPUT CURRENT (A) 800 8 6 4 130 FREQ = INTVCC 500 FREQ = GND 400 300 200 100 0 130 105 22554 G21 14 VOUT = 28V 105 80 55 30 TEMPERATURE (C) 5 Oscillator Frequency vs Temperature 2 80 5 55 30 TEMPERATURE (C) 802 Shutdown Input Current vs Input Voltage VOUT = 3.3V 5 25 20 30 15 INPUT VOLTAGE (V) 10 35 3858 G22 40 0 -45 -20 80 55 30 TEMPERATURE (C) 5 3858 G23 105 130 3858 G24 Undervoltage Lockout Threshold vs Temperature Oscillator Frequency vs Input Voltage 4.4 356 FREQ = GND 4.3 354 4.2 INTVCC VOLTAGE (V) OSCILLATOR FREQUENCY (kHz) SENSE- CURRENT (A) SENSE- Pin Input Current vs Temperature -20 804 3858 G20 3858 G19 50 0 -50 -100 -150 -200 -250 -300 -350 -400 -450 -500 -550 -600 -45 806 352 350 348 4.1 4.0 3.9 3.8 3.7 3.6 346 3.5 344 5 10 25 20 30 15 INPUT VOLTAGE (V) 35 40 3858 G28 3.4 -45 -20 55 30 5 80 TEMPERATURE (C) 105 130 3858 G25 3858fc 7 LTC3858 TYPICAL PERFORMANCE CHARACTERISTICS Latch-Off Threshold Voltages vs Temperature INTVCC and EXTVCC vs Load Current 5.20 2.3 VIN = 12V 2.2 2.1 INTVCC VOLTAGE (V) INTVCC VOLTAGE (V) 5.15 5.10 EXTVCC = 0V 5.05 EXTVCC = 8V 5.00 ARMING THRESHOLD 2.0 1.9 1.8 1.7 1.6 LATCH-OFF THRESHOLD 1.5 1.4 1.3 4.95 0 20 40 60 80 100 120 140 160 180 200 LOAD CURRENT (mA) 3858 G26 1.2 -45 -20 55 30 5 80 TEMPERATURE (C) 105 130 3858 G27 PIN FUNCTIONS SENSE1-, SENSE2- (Pin 1, Pin 9): The (-) Input to the Differential Current Comparators. When greater than INTVCC - 0.5V, the SENSE- pin supplies current to the current comparator. CLKOUT (Pin 4): Output clock signal available to daisychain other controller ICs for additional MOSFET driver stages/phases. The output levels swing from INTVCC to ground. FREQ (Pin 2): The Frequency Control Pin for the Internal Voltage-Controlled Oscillator (VCO). Connecting this pin to GND forces the VCO to a fixed low frequency of 350kHz. Connecting this pin to INTVCC forces the VCO to a fixed high frequency of 535kHz. Other frequencies between 50kHz and 900kHz can be programmed using a resistor between FREQ and GND. An internal 20A pull-up current develops the voltage to be used by the VCO to control the frequency PLLIN/MODE (Pin 5): External Synchronization Input to Phase Detector and Forced Continuous Mode Input. When an external clock is applied to this pin, the phase-locked loop will force the rising TG1 signal to be synchronized with the rising edge of the external clock. When not synchronizing to an external clock, this input, which acts on both controllers, determines how the LTC3858 operates at light loads. Pulling this pin to ground selects Burst Mode operation. An internal 100k resistor to ground also invokes Burst Mode operation when the pin is floated. Tying this pin to INTVCC forces continuous inductor current operation. Tying this pin to a voltage greater than 1.2V and less than INTVCC - 1.3V selects pulse-skipping operation. PHASMD (Pin 3): Control input to phase selector which determines the phase relationships between controller 1, controller 2 and the CLKOUT signal. Pulling this pin to ground forces TG2 and CLKOUT to be out of phase 180 and 60 with respect to TG1. Connecting this pin to INTVCC forces TG2 and CLKOUT to be out of phase 240 and 120 with respect to TG1. Floating this pin forces TG2 and CLKOUT to be out of phase 180 and 90 with respect to TG1. Refer to the Table 1. SGND (Pin 6, Exposed Pad Pin 33): Small-signal ground common to both controllers, must be routed separately from high current grounds to the common (-) terminals of the CIN capacitors. The exposed pad must be soldered to the PCB for rated thermal performance. 3858fc 8 LTC3858 PIN FUNCTIONS RUN1, RUN2 (Pin 7, Pin 8): Digital Run Control Inputs for Each Controller. Forcing either of these pins below 1.2V shuts down that controller. Forcing both of these pins below 0.7V shuts down the entire LTC3858, reducing quiescent current to approximately 8A. Do NOT float these pins. ILIM (Pin 28): Current Comparator Sense Voltage Range Inputs. Tying this pin to SGND, FLOAT or INTVCC sets the maximum current sense threshold to one of three different levels for both comparators. INTVCC (Pin 19): Output of the Internal Linear Low Dropout Regulator. The driver and control circuits are powered from this voltage source. Must be decoupled to power ground with a minimum of 4.7F ceramic or other low ESR capacitor. Do not use the INTVCC pin for any other purpose. EXTVCC (Pin 20): External Power Input to an Internal LDO Connected to INTVCC. This LDO supplies INTVCC power, bypassing the internal LDO powered from VIN whenever EXTVCC is higher than 4.7V. See EXTVCC Connection in the Applications Information section. Do not exceed 14V on this pin. PGND (Pin 21): Driver Power Ground. Connects to the sources of bottom (synchronous) N-channel MOSFETs and the (-) terminal(s) of CIN. VIN (Pin 22): Main Input Supply Pin. A bypass capacitor should be tied between this pin and the signal ground pin. BG1, BG2 (Pin 23, Pin 18): High Current Gate Drives for Bottom (Synchronous) N-Channel MOSFETs. Voltage swing at these pins is from ground to INTVCC. SW1, SW2 (Pin 25, Pin 16): Switch Node Connections to Inductors. TG1, TG2 (Pin 26, Pin 15): High Current Gate Drives for Top N-Channel MOSFETs. These are the outputs of floating drivers with a voltage swing equal to INTVCC - 0.5V superimposed on the switch node voltage SW. PGOOD1, PGOOD2 (Pin 27, Pin 14): Open-Drain Logic Output. PGOOD1,2 is pulled to ground when the voltage on the VFB1,2 pin is not within 10% of its set point. SS1, SS2 (Pin 29, Pin 13): External Soft-Start Input. The LTC3858 regulates the VFB1,2 voltage to the smaller of 0.8V or the voltage on the SS1,2 pin. An internal 1A pull-up current source is connected to this pin. A capacitor to ground at this pin sets the ramp time to final regulated output voltage. This pin is also used as the short-circuit latchoff timer. ITH1, ITH2 (Pin 30, Pin 12): Error Amplifier Outputs and Switching Regulator Compensation Points. Each associated channel's current comparator trip point increases with this control voltage. VFB1, VFB2 (Pin 31, Pin 11): Receives the remotely sensed feedback voltage for each controller from an external resistive divider across the output. SENSE1+, SENSE2+ (Pin 32, Pin 10): The (+) Input to the differential current comparators that are normally connected to inductor DCR sensing networks or current sensing resistors. The ITH pin voltage and controlled offsets between the SENSE- and SENSE+ pins in conjunction with RSENSE set the current trip threshold. BOOST1, BOOST2 (Pin 24, Pin 17): Bootstrapped Supplies to the Topside Floating Drivers. Capacitors are connected between the BOOST and SW pins and Schottky diodes are tied between the BOOST and INTVCC pins. Voltage swing at the BOOST pins is from INTVCC to (VIN + INTVCC). 3858fc 9 LTC3858 FUNCTIONAL DIAGRAM VIN INTVCC PGOOD1 27 0.88V PHASMD CLKOUT 3 4 DUPLICATE FOR SECOND CONTROLLER CHANNEL + - VFB1 DROP OUT DET + - + PGOOD2 14 0.72V 0.88V S Q R Q TOP BOT SWITCH LOGIC BOT - SHDN INTVCC + 0.72V TG 26, 15 CB D CIN BG 23, 18 COUT PGND - 20A FREQ DB SW 25, 16 TOP ON VFB2 BOOST 24, 17 VOUT 21 VCO 2 CLK2 0.425V CLK1 + SLEEP RSENSE L - ICMP PFD + - CLP -+ +- IR - SENSE+ 32, 10 + 3mV SYNC DET PLLIN/MODE 2.7V 0.55V SENSE- 1, 9 5 100k SLOPE COMP ILIM VFB 31, 11 CURRENT LIMIT RB + 28 EA VIN 0.80V TRACK/SS RA - 22 - 20 5.1V 5.1V LDO EN LDO EN + 4.7V + OV EXTVCC 0.5A SHDN RST 2(VFB) 6 SGND 19 INTVCC RUN 7, 8 CC CC2 FOLDBACK 1A 11V - ITH 30, 12 0.88V SHORT CKT LATCH-OFF RC SS 29, 13 CSS SHDN 10A 3858 FD 3858fc 10 LTC3858 OPERATION (Refer to the Functional Diagram) The LTC3858 uses a constant frequency, current mode step-down architecture with the two controller channels operating 180 degrees out of phase. During normal operation, each external top MOSFET is turned on when the clock for that channel sets the RS latch, and is turned off when the main current comparator, ICMP, resets the RS latch. The peak inductor current at which ICMP trips and resets the latch is controlled by the voltage on the ITH pin, which is the output of the error amplifier, EA. The error amplifier compares the output voltage feedback signal at the VFB pin (which is generated with an external resistor divider connected across the output voltage, VOUT , to ground) to the internal 0.800V reference voltage. When the load current increases, it causes a slight decrease in VFB relative to the reference, which causes the EA to increase the ITH voltage until the average inductor current matches the new load current. Shutdown and Start-Up (RUN1, RUN2 and SS1, SS2 Pins) After the top MOSFET is turned off each cycle, the bottom MOSFET is turned on until either the inductor current starts to reverse, as indicated by the current comparator IR, or the beginning of the next clock cycle. The start-up of each controller's output voltage, VOUT , is controlled by the voltage on the SS pin for that channel. When the voltage on the SS pin is less than the 0.8V internal reference, the LTC3858 regulates the VFB voltage to the SS pin voltage instead of the 0.8V reference. This allows the SS pin to be used to program a soft-start by connecting an external capacitor from the SS pin to SGND. An internal 1A pull-up current charges this capacitor creating a voltage ramp on the SS pin. As the SS voltage rises linearly from 0V to 0.8V (and beyond up to the absolute maximum rating of 6V), the output voltage VOUT rises smoothly from zero to its final value. INTVCC/EXTVCC Power Power for the top and bottom MOSFET drivers and most other internal circuitry is derived from the INTVCC pin. When the EXTVCC pin is left open or tied to a voltage less than 4.7V, the VIN LDO (low dropout linear regulator) supplies 5.1V from VIN to INTVCC. If EXTVCC is taken above 4.7V, the VIN LDO is turned off and the EXTVCC LDO is turned on. Once enabled, the EXTVCC LDO supplies 5.1V from EXTVCC to INTVCC. Using the EXTVCC pin allows the INTVCC power to be derived from a high efficiency external source such as one of the LTC3858 switching regulator outputs. Each top MOSFET driver is biased from the floating bootstrap capacitor, CB, which normally recharges during each switching cycle through an external diode when the top MOSFET turns off. If the input voltage, VIN, decreases to a voltage close to VOUT , the loop may enter dropout and attempt to turn on the top MOSFET continuously. The dropout detector detects this and forces the top MOSFET off for about one-twelfth of the clock period every tenth cycle to allow CB to recharge. The two channels of the LTC3858 can be independently shut down using the RUN1 and RUN2 pins. Pulling either of these pins below 1.26V shuts down the main control loop for that controller. Pulling both pins below 0.7V disables both controllers and most internal circuits, including the INTVCC LDOs. In this state, the LTC3858 draws only 8A of quiescent current. The RUN pin may be externally pulled up or driven directly by logic. When driving the RUN pin with a low impedance source, do not exceed the absolute maximum rating of 8V. The RUN pin has an internal 11V voltage clamp that allows the RUN pin to be connected through a resistor to a higher voltage (for example, VIN), so long as the maximum current into the RUN pin does not exceed 100A. Short-Circuit Latch-Off After the controller has been started and been given adequate time to ramp up the output voltage, the SS capacitor is used in a short-circuit time-out circuit. Specifically, once the voltage on the SS pin rises above 2V (the arming threshold), the short-circuit timeout circuit is enabled (see Figure 1). If the output voltage falls below 70% of its nominal regulated voltage, the SS capacitor begins discharging with a net 9A pull-down current on the assumption that the output is in an overcurrent and/or short-circuit condition. If the condition lasts long enough 3858fc 11 LTC3858 OPERATION (Refer to the Functional Diagram) limit in proportion to the severity of the overcurrent or short-circuit condition. Even if a short circuit is present and the short-circuit latch-off is not yet armed (when SS voltage has not yet reached 2V), a safe, low output current is provided due to internal current foldback and actual power wasted is low due to the efficient nature of the current mode switching regulator. Foldback current limiting is disabled during the soft-start interval (as long as the VFB voltage is keeping up with the SS voltage). INTVCC SS VOLTAGE 2V 1.5V 0.8V LATCH-OFF COMMAND 0V SS PIN CURRENT 1A 1A -9A OUTPUT VOLTAGE LATCH-OFF ENABLE 3858 F01 ARMING tLATCH SOFT-START INTERVAL Figure 1. Latch-Off Timing Diagram to allow the SS pin voltage to fall below 1.5V (the latchoff threshold), the controller will shut down (latch off) until the RUN pin voltage or the VIN voltage is recycled. The delay time from when a short-circuit occurs until the controller latches off can be calculated using the following equation tLATCH CSS VSS - 1.5V 9A where VSS is the initial voltage (must be greater than 2V) on the SS pin at the time the short-circuit occurs. Normally the SS pin voltage will have been pulled up to the INTVCC voltage (5.1V) by the internal 1A pull-up current. Note that the two controllers on the LTC3858 have separate, independent short-circuit latchoff circuits. Latchoff can be overridden/defeated by connecting a resistor 150k or less from the SS pin to INTVCC. This resistor provides enough pull-up current to overcome the 9A pull-down current present during a short-circuit. Note that this resistor also shortens the soft-start period. Foldback Current On the other hand, when the output voltage falls to less than 70% of its nominal level, foldback current limiting is also activated, progressively lowering the peak current Light Load Current Operation (Burst Mode Operation, Pulse-Skipping or Forced Continuous) (PLLIN/MODE Pin) The LTC3858 can be enabled to enter high efficiency Burst Mode operation, constant frequency pulse-skipping mode, or forced continuous conduction mode at low load currents. To select Burst Mode operation, tie the PLLIN/ MODE pin to ground. To select forced continuous operation, tie the PLLIN/MODE pin to INTVCC. To select pulse-skipping mode, tie the PLLIN/MODE pin to a DC voltage greater than 1.2V and less than INTVCC - 1.3V. When a controller is enabled for Burst Mode operation, the minimum peak current in the inductor is set to approximately 30% of the maximum sense voltage even though the voltage on the ITH pin indicates a lower value. If the average inductor current is higher than the load current, the error amplifier EA will decrease the voltage on the ITH pin. When the ITH voltage drops below 0.425V, the internal sleep signal goes high (enabling "sleep" mode) and both external MOSFETs are turned off. In sleep mode, much of the internal circuitry is turned off, reducing the quiescent current. If one channel is shut down and the other channel is in sleep mode, the LTC3858 draws only 170A of quiescent current. If both channels are in sleep mode, the LTC3858 draws only 300A of quiescent current. In sleep mode, the load current is supplied by the output capacitor. As the output voltage decreases, the EA's output begins to rise. When the output voltage drops enough, the ITH pin is reconnected to the output of the EA, the sleep signal goes low, and the controller resumes normal operation by turning on the top external MOSFET on the next cycle of the internal oscillator. 3858fc 12 LTC3858 OPERATION (Refer to the Functional Diagram) When a controller is enabled for Burst Mode operation, the inductor current is not allowed to reverse. The reverse current comparator, IR, turns off the bottom external MOSFET just before the inductor current reaches zero, preventing it from reversing and going negative. Thus, the controller is in discontinuous operation. In forced continuous operation or when clocked by an external clock source to use the phase-locked loop (see Frequency Selection and Phase-Locked Loop section), the inductor current is allowed to reverse at light loads or under large transient conditions. The peak inductor current is determined by the voltage on the ITH pin, just as in normal operation. In this mode, the efficiency at light loads is lower than in Burst Mode operation. However, continuous operation has the advantages of lower output voltage ripple and less interference to audio circuitry. In forced continuous mode, the output ripple is independent of load current. When the PLLIN/MODE pin is connected for pulse-skipping mode, the LTC3858 operates in PWM pulse-skipping mode at light loads. In this mode, constant frequency operation is maintained down to approximately 1% of designed maximum output current. At very light loads, the current comparator, ICMP, may remain tripped for several cycles and force the external top MOSFET to stay off for the same number of cycles (i.e., skipping pulses). The inductor current is not allowed to reverse (discontinuous operation). This mode, like forced continuous operation, exhibits low output ripple as well as low audio noise and reduced RF interference when compared to Burst Mode operation. It provides higher light load efficiency than forced continuous mode, but not nearly as high as Burst Mode operation. Frequency Selection and Phase-Locked Loop (FREQ and PLLIN/MODE Pins) The selection of switching frequency is a tradeoff between efficiency and component size. Low frequency operation increases efficiency by reducing MOSFET switching losses, but requires larger inductance and/or capacitance to maintain low output ripple voltage. The switching frequency of the LTC3858's controllers can be selected using the FREQ pin. If the PLLIN/MODE pin is not being driven by an external clock source, the FREQ pin can be tied to SGND, tied to INTVCC or programmed through an external resistor. Tying FREQ to SGND selects 350kHz while tying FREQ to INTVCC selects 535kHz. Placing a resistor between FREQ and SGND allows the frequency to be programmed between 50kHz and 900kHz, as shown in Figure 9 A phase-locked loop (PLL) is available on the LTC3858 to synchronize the internal oscillator to an external clock source that is connected to the PLLIN/MODE pin. The phase detector adjusts the voltage (through an internal lowpass filter) of the VCO input to align the turn-on of controller 1's external top MOSFET to the rising edge of the synchronizing signal. Thus, the turn-on of controller 2's external top MOSFET is 180 degrees out of phase to the rising edge of the external clock source. The VCO input voltage is pre-biased to the operating frequency set by the FREQ pin before the external clock is applied. If prebiased near the external clock frequency, the PLL loop only needs to make slight changes to the VCO input in order to synchronize the rising edge of the external clock's to the rising edge of TG1. The ability to pre-bias the loop filter allows the PLL to lock-in rapidly without deviating far from the desired frequency. The typical capture range of the phase-locked loop is from approximately 55kHz to 1MHz, with a guarantee over all manufacturing variations to be between 75kHz and 850kHz. In other words, the LTC3858's PLL is guaranteed to lock to an external clock source whose frequency is between 75kHz and 850kHz. The typical input clock thresholds on the PLLIN/MODE pin are 1.6V (rising) and 1.1V (falling). PolyPhase(R) Applications (CLKOUT and PHASMD Pins) The LTC3858 features two pins (CLKOUT and PHASMD) that allow other controller ICs to be daisy-chained with the LTC3858 in PolyPhase applications. The clock output signal on the CLKOUT pin can be used to synchronize additional power stages in a multiphase power supply solution feeding a single, high current output or multiple separate outputs. The PHASMD pin is used to adjust the phase of the CLKOUT signal as well as the relative phases 3858fc 13 LTC3858 OPERATION (Refer to the Functional Diagram) between the two internal controllers, as summarized in Table 1. The phases are calculated relative to the zero degrees phase being defined as the rising edge of the top gate driver output of controller 1 (TG1). Table 1 VPHASMD CONTROLLER 2 PHASE CLKOUT PHASE GND 180 60 Floating 180 90 INTVCC 240 120 Output Overvoltage Protection An overvoltage comparator guards against transient overshoots as well as other more serious conditions that may overvoltage the output. When the VFB pin rises by more than 10% above its regulation point of 0.800V, the top MOSFET is turned off and the bottom MOSFET is turned on until the overvoltage condition is cleared. Power Good (PGOOD1 and PGOOD2) Pins Each PGOOD pin is connected to an open drain of an internal N-channel MOSFET. The MOSFET turns on and pulls the PGOOD pin low when the corresponding VFB pin voltage is not within 10% of the 0.8V reference voltage. The PGOOD pin is also pulled low when the corresponding RUN pin is low (shut down). When the VFB pin voltage is within the 10% requirement, the MOSFET is turned off and the pin is allowed to be pulled up by an external resistor to a source no greater than 6V. Theory and Benefits of 2-Phase Operation Why the need for 2-phase operation? Up until the 2-phase family, constant frequency dual switching regulators operated both channels in phase (i.e., single phase operation). This means that both switches turned on at the same time, causing current pulses of up to twice the amplitude of those for one regulator to be drawn from the input capacitor and battery. These large amplitude current pulses increased the total RMS current flowing from the input capacitor, requiring the use of more expensive input capacitors and increasing both EMI and losses in the input capacitor and battery. With 2-phase operation, the two channels of the dual switching regulator are operated 180 degrees out of phase. This effectively interleaves the current pulses drawn by the switches, greatly reducing the overlap time where they add together. The result is a significant reduction in total RMS input current, which in turn allows less expensive input capacitors to be used, reduces shielding requirements for EMI and improves real world operating efficiency. Figure 2 compares the input waveforms for a representative single-phase dual switching regulator to the LTC3858 2-phase dual switching regulator. An actual measurement of the RMS input current under these conditions shows that 2-phase operation dropped the input current from 2.53ARMS to 1.55ARMS. While this is an impressive reduction in itself, remember that the power losses are proportional to IRMS2, meaning that the actual power wasted is reduced by a 5V SWITCH 20V/DIV 3.3V SWITCH 20V/DIV INPUT CURRENT 5A/DIV INPUT VOLTAGE 500mV/DIV IIN(MEAS) = 2.53ARMS IIN(MEAS) = 1.55ARMS 3858 F02 Figure 2. Input Waveforms Comparing Single-Phase (a) and 2-Phase (b) Operation for Dual Switching Regulators Converting 12V to 5V and 3.3V at 3A Each. The Reduced Input Ripple with the 2-Phase Regulator Allows Less Expensive Input Capacitors, Reduces Shielding Requirements for EMI and Improves Efficiency 3858fc 14 LTC3858 OPERATION (Refer to the Functional Diagram) factor of 2.66. The reduced input ripple voltage also means less power is lost in the input power path, which could include batteries, switches, trace/connector resistances and protection circuitry. Improvements in both conducted and radiated EMI also directly accrue as a result of the reduced RMS input current and voltage. Of course, the improvement afforded by 2-phase operation is a function of the dual switching regulator's relative duty cycles which, in turn, are dependent upon the input voltage VIN (Duty Cycle = VOUT/VIN). Figure 3 shows how the RMS input current varies for single phase and 2-phase operation for 3.3V and 5V regulators over a wide input voltage range. It can readily be seen that the advantages of 2-phase operation are not just limited to a narrow operating range, for most applications is that 2-phase operation will reduce the input capacitor requirement to that for just one channel operating at maximum current and 50% duty cycle. 3.0 SINGLE PHASE DUAL CONTROLLER INPUT RMS CURRENT (A) 2.5 2.0 1.5 2-PHASE DUAL CONTROLLER 1.0 0.5 0 VO1 = 5V/3A VO2 = 3.3V/3A 0 10 20 30 INPUT VOLTAGE (V) 40 3858 F03 Figure 3. RMS Input Current Comparison 3858fc 15 LTC3858 APPLICATIONS INFORMATION The Typical Application on the first page is a basic LTC3858 application circuit. LTC3858 can be configured to use either DCR (inductor resistance) sensing or low value resistor sensing. The choice between the two current sensing schemes is largely a design tradeoff between cost, power consumption and accuracy. DCR sensing is becoming popular because it saves expensive current sensing resistors and is more power efficient, especially in high current applications. However, current sensing resistors provide the most accurate current limits for the controller. Other external component selection is driven by the load requirement, and begins with the selection of RSENSE (if RSENSE is used) and inductor value. Next, the power MOSFETs and Schottky diodes are selected. Finally, input and output capacitors are selected. Filter components mutual to the sense lines should be placed close to the LTC3858, and the sense lines should run close together to a Kelvin connection underneath the current sense element (shown in Figure 4). Sensing current elsewhere can effectively add parasitic inductance and capacitance to the current sense element, degrading the information at the sense terminals and making the programmed current limit unpredictable. If inductor DCR sensing is used (Figure 5b), resistor R1 should be placed close to the switching node, to prevent noise from coupling into sensitive small-signal nodes. TO SENSE FILTER, NEXT TO THE CONTROLLER COUT 3858 F04 Current Limit Programming The ILIM pin is a tri-level logic input which sets the maximum current limit of the converter. When ILIM is grounded, the maximum current limit threshold voltage of the current comparator is programmed to be 30mV. When ILIM is floated, the maximum current limit threshold is 50mV. When ILIM is tied to INTVCC, the maximum current limit threshold is set to 75mV. SENSE+ and SENSE- Pins The SENSE+ and SENSE- pins are the inputs to the current comparators. The common mode voltage range on these pins is 0V to 28V (Abs Max), enabling the LTC3858 to regulate output voltages up to a nominal 24V (allowing margin for tolerances and transients). The SENSE+ pin is high impedance over the full common mode range, drawing at most 1A. This high impedance allows the current comparators to be used in inductor DCR sensing. The impedance of the SENSE- pin changes depending on the common mode voltage. When SENSE- is less than INTVCC - 0.5V, a small current of less than 1A flows out of the pin. When SENSE- is above INTVCC + 0.5V, a higher current (~550A) flows into the pin. Between INTVCC - 0.5V and INTVCC + 0.5V, the current transitions from the smaller current to the higher current. INDUCTOR OR RSENSE Figure 4. Sense Lines Placement with Inductor or Sense Resistor Low Value Resistor Current Sensing A typical sensing circuit using a discrete resistor is shown in Figure 5a. RSENSE is chosen based on the required output current. The current comparator has a maximum threshold VSENSE(MAX) determined by the ILIM setting. The current comparator threshold voltage sets the peak of the inductor current, yielding a maximum average output current, IMAX, equal to the peak value less half the peak-to-peak ripple current, IL. To calculate the sense resistor value, use the equation: R SENSE = VSENSE(MAX) I IMAX + L 2 When using the controller in very low dropout conditions, the maximum output current level will be reduced due to the internal compensation required to meet stability criterion for buck regulators operating at greater than 50% duty factor. A curve is provided in the Typical Performance Characteristics section to estimate this reduction in peak output current depending upon the operating duty factor. 3858fc 16 LTC3858 APPLICATIONS INFORMATION Inductor DCR Sensing For applications requiring the highest possible efficiency at high load currents, the LTC3850 is capable of sensing the voltage drop across the inductor DCR, as shown in Figure 5b. The DCR of the inductor represents the small amount of DC resistance of the copper wire, which can be less than 1m for today's low value, high current inductors. In a high current application requiring such an inductor, power loss through a sense resistor would cost several points of efficiency compared to inductor DCR sensing. If the external R1||R2 * C1 time constant is chosen to be exactly equal to the L/DCR time constant, the voltage drop across the external capacitor is equal to the drop across the inductor DCR multiplied by R2/(R1 + R2). R2 scales the voltage across the sense terminals for applications where the DCR is greater than the target sense resistor value. To properly dimension the external filter components, the DCR of the inductor must be known. It can be measured using a good RLC meter, but the DCR tolerance is not always the same and varies with temperature; consult the manufacturers' data sheets for detailed information. Using the inductor ripple current value from the Inductor Value Calculation section, the target sense resistor value is: R SENSE(EQUIV) = To ensure that the application will deliver full load current over the full operating temperature range, choose the minimum value for the Maximum Current Sense Threshold Voltage (VSENSE(MAX)) in the Electrical Characteristics table (30mV, 50mV or 75mV depending on the state of the ILIM pin). Next, determine the DCR of the inductor. When provided, use the manufacturer's maximum value, usually given at 20C. Increase this value to account for the temperature coefficient of copper, which is approximately 0.4%/C. A conservative value for TL(MAX) is 100C. To scale the maximum inductor DCR to the desired sense resistor (RD) value, use the divider ratio: RD = RSENSE(EQUIV) DCRMAX at TL(MAX) C1 is usually selected to be in the range of 0.1F to 0.47F. This forces R1||R2 to around 2k, reducing error that might have been caused by the SENSE+ pin's 1A current. The equivalent resistance R1||R2 is scaled to the room temperature inductance and maximum DCR: R1|| R2 = L (DCR at 20C) * C1 VSENSE(MAX) I IMAX + L 2 VIN INTVCC VIN BOOST BOOST INDUCTOR TG TG VIN INTVCC VIN RSENSE L DCR VOUT SW VOUT SW LTC3858 LTC3858 BG BG SENSE+ SENSE+ SENSE- PLACE CAPACITOR NEAR SENSE PINS R1 C1* R2 SENSE- SGND SGND 3858 F05a (5a) Using a Resistor to Sense Current *PLACE C1 NEAR SENSE PINS (R1||R2) * C1 = L DCR RSENSE(EQ) = DCR R2 R1 + R2 3858 F05b (5b) Using the Inductor DCR to Sense Current Figure 5. Current Sensing Methods 3858fc 17 LTC3858 APPLICATIONS INFORMATION The sense resistor values are: R1= R1|| R2 R1* RD ; R2 = RD 1- RD The maximum power loss in R1 is related to duty cycle, and will occur in continuous mode at the maximum input voltage: PLOSS R1= ( VIN(MAX) - VOUT ) * VOUT R1 Ensure that R1 has a power rating higher than this value. If high efficiency is necessary at light loads, consider this power loss when deciding whether to use inductor DCR sensing or sense resistors. Light load power loss can be modestly higher with a DCR network than with a sense resistor, due to the extra switching losses incurred through R1. However, DCR sensing eliminates a sense resistor, reduces conduction losses and provides higher efficiency at heavy loads. Peak efficiency is about the same with either method. Inductor Value Calculation setting ripple current is IL = 0.3(IMAX). The maximum IL occurs at the maximum input voltage. The inductor value also has secondary effects. The transition to Burst Mode operation begins when the average inductor current required results in a peak current below 30% of the current limit determined by RSENSE. Lower inductor values (higher IL) will cause this to occur at lower load currents, which can cause a dip in efficiency in the upper range of low current operation. In Burst Mode operation, lower inductance values will cause the burst frequency to decrease. Inductor Core Selection Once the value for L is known, the type of inductor must be selected. High efficiency converters generally cannot afford the core loss found in low cost powdered iron cores, forcing the use of more expensive ferrite or molypermalloy cores. Actual core loss is independent of core size for a fixed inductor value, but it is very dependent on inductance value selected. As inductance increases, core losses go down. Unfortunately, increased inductance requires more turns of wire and therefore copper losses will increase. The operating frequency and inductor selection are interrelated in that higher operating frequencies allow the use of smaller inductor and capacitor values. So why would anyone ever choose to operate at lower frequencies with larger components? The answer is efficiency. A higher frequency generally results in lower efficiency because of MOSFET gate charge losses. In addition to this basic tradeoff, the effect of inductor value on ripple current and low current operation must also be considered. Ferrite designs have very low core loss and are preferred for high switching frequencies, so design goals can concentrate on copper loss and preventing saturation. Ferrite core material saturates "hard," which means that inductance collapses abruptly when the peak design current is exceeded. This results in an abrupt increase in inductor ripple current and consequent output voltage ripple. Do not allow the core to saturate! The inductor value has a direct effect on ripple current. The inductor ripple current IL decreases with higher inductance or higher frequency and increases with higher VIN: Power MOSFET and Schottky Diode (Optional) Selection IL = 1 V VOUT 1- OUT VIN ( f ) (L ) Accepting larger values of IL allows the use of low inductances, but results in higher output voltage ripple and greater core losses. A reasonable starting point for Two external power MOSFETs must be selected for each controller in the LTC3858: one N-channel MOSFET for the top (main) switch, and one N-channel MOSFET for the bottom (synchronous) switch. The peak-to-peak drive levels are set by the INTVCC voltage. This voltage is typically 5.2V during start-up (see EXTVCC Pin Connection). Consequently, logic-level threshold MOSFETs must be used in most applications. The only 3858fc 18 LTC3858 APPLICATIONS INFORMATION exception is if low input voltage is expected (VIN < 4V); then, sub-logic level threshold MOSFETs (VGS(TH) < 3V) should be used. Pay close attention to the BVDSS specification for the MOSFETs as well; many of the logic-level MOSFETs are limited to 30V or less. Selection criteria for the power MOSFETs include the "ON" resistance, RDS(ON), Miller capacitance, CMILLER, input voltage and maximum output current. Miller capacitance, CMILLER, can be approximated from the gate charge curve usually provided on the MOSFET manufacturers' data sheet. CMILLER is equal to the increase in gate charge along the horizontal axis while the curve is approximately flat divided by the specified change in VDS. This result is then multiplied by the ratio of the application applied VDS to the gate charge curve specified VDS. When the IC is operating in continuous mode the duty cycles for the top and bottom MOSFETs are given by: Main Switch Duty Cycle = VOUT VIN Synchronous Switch Duty Cycle = VIN - VOUT VIN The MOSFET power dissipations at maximum output current are given by: PMAIN = VOUT (IMAX )2 (1+ )RDS(ON) + VIN 2 IMAX ( VIN ) (RDR ) (CMILLER ) * 2 1 1 + V ( f) INTVCC - VTHMIN VTHMIN PSYNC = VIN - VOUT (IMAX )2 (1+ )RDS(ON) VIN where is the temperature dependency of RDS(ON) and RDR (approximately 2) is the effective driver resistance at the MOSFET's Miller threshold voltage. VTHMIN is the typical MOSFET minimum threshold voltage. Both MOSFETs have I2R losses while the topside N-channel equation includes an additional term for transition losses, which are highest at high input voltages. For VIN < 20V the high current efficiency generally improves with larger MOSFETs, while for VIN > 20V the transition losses rapidly increase to the point that the use of a higher RDS(ON) device with lower CMILLER actually provides higher efficiency. The synchronous MOSFET losses are greatest at high input voltage when the top switch duty factor is low or during a short-circuit when the synchronous switch is on close to 100% of the period. The term (1+ ) is generally given for a MOSFET in the form of a normalized RDS(ON) vs Temperature curve, but = 0.005/C can be used as an approximation for low voltage MOSFETs. The optional Schottky diodes D3 and D4 shown in Figure 12 conduct during the dead-time between the conduction of the two power MOSFETs. This prevents the body diode of the bottom MOSFET from turning on, storing charge during the dead-time and requiring a reverse recovery period that could cost as much as 3% in efficiency at high VIN. A 1A to 3A Schottky is generally a good compromise for both regions of operation due to the relatively small average current. Larger diodes result in additional transition losses due to their larger junction capacitance. CIN and COUT Selection The selection of CIN is simplified by the 2-phase architecture and its impact on the worst-case RMS current drawn through the input network (battery/fuse/capacitor). It can be shown that the worst-case capacitor RMS current occurs when only one controller is operating. The controller with the highest (VOUT)(IOUT) product needs to be used in the formula shown in Equation 1 to determine the maximum RMS capacitor current requirement. Increasing the output current drawn from the other controller will actually decrease the input RMS ripple current from its maximum value. The out-of-phase technique typically reduces the input capacitor's RMS ripple current by a factor of 30% to 70% when compared to a single phase power supply solution. 3858fc 19 LTC3858 APPLICATIONS INFORMATION In continuous mode, the source current of the top MOSFET is a square wave of duty cycle (VOUT)/(VIN). To prevent large voltage transients, a low ESR capacitor sized for the maximum RMS current of one channel must be used. The maximum RMS capacitor current is given by: CIN Required IRMS IMAX 1/ 2 ( VOUT ) ( VIN - VOUT ) (1) VIN Equation 1 has a maximum at VIN = 2VOUT , where IRMS = IOUT/2. This simple worst-case condition is commonly used for design because even significant deviations do not offer much relief. Note that capacitor manufacturers' ripple current ratings are often based on only 2000 hours of life. This makes it advisable to further derate the capacitor, or to choose a capacitor rated at a higher temperature than required. Several capacitors may be paralleled to meet size or height requirements in the design. Due to the high operating frequency of the LTC3858, ceramic capacitors can also be used for CIN. Always consult the manufacturer if there is any question. The benefit of 2-phase operation can be calculated by using Equation 1 for the higher power controller and then calculating the loss that would have resulted if both controller channels switched on at the same time. The total RMS power lost is lower when both controllers are operating due to the reduced overlap of current pulses required through the input capacitor's ESR. This is why the input capacitor's requirement calculated above for the worst-case controller is adequate for the dual controller design. Also, the input protection fuse resistance, battery resistance, and PC board trace resistance losses are also reduced due to the reduced peak currents in a 2-phase system. The overall benefit of a multiphase design will only be fully realized when the source impedance of the power supply/battery is included in the efficiency testing. The drains of the top MOSFETs should be placed within 1cm of each other and share a common CIN (s). Separating the sources and CIN may produce undesirable voltage and current resonances at VIN. A small (0.1F to 1F) bypass capacitor between the chip VIN pin and ground, placed close to the LTC3858, is also suggested. A 10 resistor placed between CIN (C1) and the VIN pin provides further isolation between the two channels. The selection of COUT is driven by the effective series resistance (ESR). Typically, once the ESR requirement is satisfied, the capacitance is adequate for filtering. The output ripple (VOUT) is approximated by: 1 VOUT IL ESR + 8 * f * COUT where fO is the operating frequency, COUT is the output capacitance and IL is the ripple current in the inductor. The output ripple is highest at maximum input voltage since IL increases with input voltage. Setting Output Voltage The LTC3858 output voltages are each set by an external feedback resistor divider carefully placed across the output, as shown in Figure 6. The regulated output voltage is determined by: R VOUT = 0.8V 1+ B RA To improve the frequency response, a feedforward capacitor, CFF , may be used. Great care should be taken to route the VFB line away from noise sources, such as the inductor or the SW line. VOUT 1/2 LTC3858 RB CFF VFB RA 3858 F06 Figure 6. Setting Output Voltage Soft-Start (SS Pins) The start-up of each VOUT is controlled by the voltage on the respective SS pin. When the voltage on the SS pin is less than the internal 0.8V reference, the LTC3858 regulates the VFB pin voltage to the voltage on the SS pin instead of 0.8V. The SS pin can be used to program an external soft-start function. 3858fc 20 LTC3858 APPLICATIONS INFORMATION Soft-start is enabled by simply connecting a capacitor from the SS pin to ground, as shown in Figure 7. An internal 1A current source charges the capacitor, providing a linear ramping voltage at the SS pin. The LTC3858 will regulate the VFB pin (and hence VOUT) according to the voltage on the SS pin, allowing VOUT to rise smoothly from 0V to its final regulated value. The total soft-start time will be approximately: tSS = CSS as discussed in the Efficiency Considerations section. The junction temperature can be estimated by using the equations given in Note 3 of the Electrical Characteristics. For example, the LTC3858 INTVCC current is limited to less than 32mA from a 40V supply when not using the EXTVCC supply at 70C ambient temperature: TJ = 70C + (32mA)(40V)(43C/W) = 125C To prevent the maximum junction temperature from being exceeded, the input supply current must be checked while operating in forced continuous mode (PLLIN/MODE = INTVCC) at maximum VIN. 0.8V * 1A 1/2 LTC3858 SS CSS SGND 3858 F07 Figure 7. Using the TRACK/SS Pin to Program Soft-Start INTVCC Regulators The LTC3858 features two separate internal P-channel low dropout linear regulators (LDO) that supply power at the INTVCC pin from either the VIN supply pin or the EXTVCC pin depending on the connection of the EXTVCC pin. INTVCC powers the gate drivers and much of the internal circuitry. The VIN LDO and the EXTVCC LDO regulate INTVCC to 5.1V. Each of these can supply a peak current of 50mA and must be bypassed to ground with a minimum of 4.7F low ESR capacitor. Regardless of what type of bulk capacitor is used, an additional 1F ceramic capacitor placed directly adjacent to the INTVCC and PGND pins is highly recommended. Good bypassing is needed to supply the high transient currents required by the MOSFET gate drivers and to prevent interaction between the channels. High input voltage applications in which large MOSFETs are being driven at high frequencies may cause the maximum junction temperature rating for the LTC3858 to be exceeded. The INTVCC current, which is dominated by the gate charge current, may be supplied by either the VIN LDO or the EXTVCC LDO. When the voltage on the EXTVCC pin is less than 4.7V, the VIN LDO is enabled. Power dissipation for the IC in this case is highest and is equal to VIN * IINTVCC. The gate charge current is dependent on operating frequency When the voltage applied to EXTVCC rises above 4.7V, the VIN LDO is turned off and the EXTVCC LDO is enabled. The EXTVCC LDO remains on as long as the voltage applied to EXTVCC remains above 4.5V. The EXTVCC LDO attempts to regulate the INTVCC voltage to 5.1V, so while EXTVCC is less than 5.1V, the LDO is in dropout and the INTVCC voltage is approximately equal to EXTVCC. When EXTVCC is greater than 5.1V, up to an absolute maximum of 14V, INTVCC is regulated to 5.1V. Using the EXTVCC LDO allows the MOSFET driver and control power to be derived from one of the switching regulator outputs (4.7V VOUT 14V) during normal operation and from the VIN LDO when the output is out of regulation (e.g., start-up, short-circuit). If more current is required through the EXTVCC LDO than is specified, an external Schottky diode can be added between the EXTVCC and INTVCC pins. In this case, do not apply more than 6V to the EXTVCC pin and make sure that EXTVCC VIN. Significant efficiency and thermal gains can be realized by powering INTVCC from the output, since the VIN current resulting from the driver and control currents will be scaled by a factor of (Duty Cycle)/(Switcher Efficiency). For 5V to 14V regulator outputs, this means connecting the EXTVCC pin directly to VOUT . Tying the EXTVCC pin to an 8.5V supply reduces the junction temperature in the previous example from 125C to: TJ = 70C + (32mA)(8.5V)(43C/W) = 82C However, for 3.3V and other low voltage outputs, additional circuitry is required to derive INTVCC power from the output. 3858fc 21 LTC3858 APPLICATIONS INFORMATION The following list summarizes the four possible connections for EXTVCC: 1. EXTVCC Left Open (or Grounded). This will cause INTVCC to be powered from the internal 5.1V regulator resulting in an efficiency penalty of up to 10% at high input voltages. 2. EXTVCC Connected Directly to VOUT . This is the normal connection for a 5V to 14V regulator and provides the highest efficiency. 3. EXTVCC Connected to an External Supply. If an external supply is available in the 5V to 14V range, it may be used to power EXTVCC. Ensure that EXTVCC < VIN. 4. EXTVCC Connected to an Output-Derived Boost Network. For 3.3V and other low voltage regulators, efficiency gains can still be realized by connecting EXTVCC to an output-derived voltage that has been boosted to greater than 4.7V. This can be done with the capacitive charge pump shown in Figure 8. Ensure that EXTVCC < VIN. VIN CIN BAT85 VIN BAT85 MTOP VN2222LL TG1 1/2 LTC3858 EXTVCC L BAT85 RSENSE VOUT SW MBOT BG1 D COUT and turns it on. The switch node voltage, SW, rises to VIN and the BOOST pin follows. With the topside MOSFET on, the boost voltage is above the input supply: VBOOST = VIN + VINTVCC. The value of the boost capacitor, CB, needs to be 100 times that of the total input capacitance of the topside MOSFET(s). The reverse breakdown of the external Schottky diode must be greater than VIN(MAX). When adjusting the gate drive level, the final arbiter is the total input current for the regulator. If a change is made and the input current decreases, then the efficiency has improved. If there is no change in input current, then there is no change in efficiency. Fault Conditions: Current Limit and Current Foldback When the output current hits the current limit, the output voltage begins to drop. If the output voltage falls below 70% of its nominal output level, then the maximum sense voltage is progressively lowered to about half of its maximum selected value. Under short-circuit conditions with very low duty cycles, the LTC3858 will begin cycle skipping in order to limit the short-circuit current. In this situation the bottom MOSFET will be dissipating most of the power but less than in normal operation. The short-circuit ripple current is determined by the minimum on-time, tON(MIN), of the LTC3858 (95ns), the input voltage and inductor value: V IL(SC) = tON(MIN) IN L The resulting average short-circuit current is: PGND 3858 F08 ISC = Figure 8. Capacitive Charge Pump for EXTVCC Topside MOSFET Driver Supply (CB, DB) External bootstrap capacitors, CB, connected to the BOOST pins supply the gate drive voltages for the topside MOSFETs. Capacitor CB in the Functional Diagram is charged though external diode DB from INTVCC when the SW pin is low. When one of the topside MOSFETs is turned on, the driver places the CB voltage across the gate-source of the desired MOSFET. This enhances the top MOSFET switch 50% * ILIM(MAX) 1 - IL(SC) RSENSE 2 Fault Conditions: Overvoltage Protection (Crowbar) The overvoltage crowbar is designed to blow a system input fuse when the output voltage of the regulator rises much higher than nominal levels. The crowbar causes huge currents to flow, that blow the fuse to protect against a shorted top MOSFET if the short occurs while the controller is operating. 3858fc 22 LTC3858 APPLICATIONS INFORMATION A comparator monitors the output for overvoltage conditions. The comparator detects faults greater than 10% above the nominal output voltage. When this condition is sensed, the top MOSFET is turned off and the bottom MOSFET is turned on until the overvoltage condition is cleared. The bottom MOSFET remains on continuously for as long as the overvoltage condition persists; if VOUT returns to a safe level, normal operation automatically resumes. A shorted top MOSFET will result in a high current condition which will open the system fuse. The switching regulator will regulate properly with a leaky top MOSFET by altering the duty cycle to accommodate the leakage. Phase-Locked Loop and Frequency Synchronization The LTC3858 has an internal phase-locked loop (PLL) comprised of a phase frequency detector, a lowpass filter, and a voltage-controlled oscillator (VCO). This allows the turn-on of the top MOSFET of controller 1 to be locked to the rising edge of an external clock signal applied to the PLLIN/MODE pin. The turn-on of controller 2's top MOSFET is thus 180 degrees out of phase with the external clock. The phase detector is an edge sensitive digital type that provides zero degrees phase shift between the external and internal oscillators. This type of phase detector does not exhibit false lock to harmonics of the external clock. When not prebiased, applying an external clock will invoke traditional PLL operation. If the external clock frequency is greater than the internal oscillator's frequency, fOSC, then current is sourced continuously from the phase detector output, pulling up the VCO input. When the external clock frequency is less than fOSC, current is sunk continuously, pulling down the VCO input. If the external and internal frequencies are the same but exhibit a phase difference, the current sources turn on for an amount of time corresponding to the phase difference. The voltage at the VCO input is adjusted until the phase and frequency of the internal and external oscillators are identical. At the stable operating point, the phase detector output is high impedance and the internal filter capacitor, CLP , holds the voltage at the VCO input. 1000 900 FREQUENCY (kHz) 800 700 600 500 400 300 200 100 0 15 25 35 45 55 65 75 85 95 105 115 125 FREQ PIN RESISTOR (k) 3858 F09 Figure 9. Relationship Between Oscillator Frequency and Resistor Value at the FREQ Pin Note that the LTC3858 can only be synchronized to an external clock whose frequency is within range of the LTC3858's internal VCO, which is nominally 55kHz to 1MHz. This is guaranteed to be between 75kHz and 850kHz. Typically, the external clock (on the PLLIN/MODE pin) input high threshold is 1.6V, while the input low threshold is 1.1V. Rapid phase locking can be achieved by using the FREQ pin to set a free-running frequency near the desired synchronization frequency. The VCO's input voltage is prebiased at a frequency corresponding to the frequency set by the FREQ pin. Once prebiased, the PLL only needs to adjust the frequency slightly to achieve phase lock and synchronization. Although it is not required that the free-running frequency be near external clock frequency, doing so will prevent the operating frequency from passing through a large range of frequencies as the PLL locks. Table 2 summarizes the different states in which the FREQ pin can be used. Table 2 FREQ PIN PLLIN/MODE PIN FREQUENCY 0V DC Voltage 350kHz INTVCC DC Voltage 535kHz Resistor DC Voltage 50kHz-900kHz Any of the Above External Clock Phase-Locked to External Clock 3858fc 23 LTC3858 APPLICATIONS INFORMATION Minimum On-Time Considerations Minimum on-time, tON(MIN), is the smallest time duration that the LTC3858 is capable of turning on the top MOSFET. It is determined by internal timing delays and the gate charge required to turn on the top MOSFET. Low duty cycle applications may approach this minimum on-time limit and care should be taken to ensure that: tON(MIN) < VOUT VIN ( f ) If the duty cycle falls below what can be accommodated by the minimum on-time, the controller will begin to skip cycles. The output voltage will continue to be regulated, but the ripple voltage and current will increase. The minimum on-time for the LTC3858 is approximately 95ns. However, as the peak sense voltage decreases the minimum on-time gradually increases up to about 130ns. This is of particular concern in forced continuous applications with low ripple current at light loads. If the duty cycle drops below the minimum on-time limit in this situation, a significant amount of cycle skipping can occur with correspondingly larger current and voltage ripple. Efficiency Considerations The percent efficiency of a switching regulator is equal to the output power divided by the input power times 100%. It is often useful to analyze individual losses to determine what is limiting the efficiency and which change would produce the most improvement. Percent efficiency can be expressed as: %Efficiency = 100% - (L1 + L2 + L3 + ...) where L1, L2, etc. are the individual losses as a percentage of input power. Although all dissipative elements in the circuit produce losses, four main sources usually account for most of the losses in LTC3858 circuits: 1) IC VIN current, 2) INTVCC regulator current, 3) I2R losses, 4) topside MOSFET transition losses. 1. The VIN current is the DC input supply current given in the Electrical Characteristics table, which excludes MOSFET driver and control currents. VIN current typically results in a small (<0.1%) loss. 2. INTVCC current is the sum of the MOSFET driver and control currents. The MOSFET driver current results from switching the gate capacitance of the power MOSFETs. Each time a MOSFET gate is switched from low to high to low again, a packet of charge, dQ, moves from INTVCC to ground. The resulting dQ/dt is a current out of INTVCC that is typically much larger than the control circuit current. In continuous mode, IGATECHG = f(QT + QB), where QT and QB are the gate charges of the topside and bottom side MOSFETs. Supplying INTVCC from an output-derived power source through EXTVCC will scale the VIN current required for the driver and control circuits by a factor of (Duty Cycle)/(Efficiency). For example, in a 20V to 5V application, 10mA of INTVCC current results in approximately 2.5mA of VIN current. This reduces the midcurrent loss from 10% or more (if the driver was powered directly from VIN) to only a few percent. 3. I2R losses are predicted from the DC resistances of the fuse (if used), MOSFET, inductor, current sense resistor, and input and output capacitor ESR. In continuous mode the average output current flows through L and RSENSE, but is "chopped" between the topside MOSFET and the synchronous MOSFET. If the two MOSFETs have approximately the same RDS(ON), then the resistance of one MOSFET can simply be summed with the resistances of L, RSENSE and ESR to obtain I2R losses. For example, if each RDS(ON) = 30m, RL = 50m, RSENSE = 10m and RESR = 40m (sum of both input and output capacitance losses), then the total resistance is 130m. This results in losses ranging from 3% to 13% as the output current increases from 1A to 5A for a 5V output, or a 4% to 20% loss for a 3.3V output. Efficiency varies as the inverse square of VOUT for the same external components and output power level. The 3858fc 24 LTC3858 APPLICATIONS INFORMATION combined effects of increasingly lower output voltages and higher currents required by high performance digital systems is not doubling but quadrupling the importance of loss terms in the switching regulator system! 4. Transition losses apply only to the topside MOSFET(s), and become significant only when operating at high input voltages (typically 15V or greater). Transition losses can be estimated from: Transition Loss = (1.7) * VIN * 2 * IO(MAX) * CRSS * f Other "hidden" losses such as copper trace and internal battery resistances can account for an additional 5% to 10% efficiency degradation in portable systems. It is very important to include these "system" level losses during the design phase. The internal battery and fuse resistance losses can be minimized by making sure that CIN has adequate charge storage and very low ESR at the switching frequency. A 25W supply will typically require a minimum of 20F to 40F of capacitance having a maximum of 20m to 50m of ESR. The LTC3858 2-phase architecture typically halves this input capacitance requirement over competing solutions. Other losses including Schottky conduction losses during dead-time and inductor core losses generally account for less than 2% total additional loss. Checking Transient Response The regulator loop response can be checked by looking at the load current transient response. Switching regulators take several cycles to respond to a step in DC (resistive) load current. When a load step occurs, VOUT shifts by an amount equal to ILOAD (ESR), where ESR is the effective series resistance of COUT . ILOAD also begins to charge or discharge COUT generating the feedback error signal that forces the regulator to adapt to the current change and return VOUT to its steady-state value. During this recovery time VOUT can be monitored for excessive overshoot or ringing, which would indicate a stability problem. OPTILOOP compensation allows the transient response to be optimized over a wide range of output capacitance and ESR values. The availability of the ITH pin not only allows optimization of control loop behavior, but it also provides a DC coupled and AC filtered closed-loop response test point. The DC step, rise time and settling at this test point truly reflects the closed-loop response. Assuming a predominantly second order system, phase margin and/ or damping factor can be estimated using the percentage of overshoot seen at this pin. The bandwidth can also be estimated by examining the rise time at the pin. The ITH external components shown in Figure 12 circuit will provide an adequate starting point for most applications. The ITH series RC-CC filter sets the dominant pole-zero loop compensation. The values can be modified slightly (from 0.5 to 2 times their suggested values) to optimize transient response once the final PC layout is done and the particular output capacitor type and value have been determined. The output capacitors need to be selected because the various types and values determine the loop gain and phase. An output current pulse of 20% to 80% of full-load current having a rise time of 1s to 10s will produce output voltage and ITH pin waveforms that will give a sense of the overall loop stability without breaking the feedback loop. Placing a resistive load and a power MOSFET directly across the output capacitor and driving the gate with an appropriate signal generator is a practical way to produce a realistic load step condition. The initial output voltage step resulting from the step change in output current may not be within the bandwidth of the feedback loop, so this signal cannot be used to determine phase margin. This is why it is better to look at the ITH pin signal which is in the feedback loop and is the filtered and compensated control loop response. The gain of the loop will be increased by increasing RC and the bandwidth of the loop will be increased by decreasing CC. If RC is increased by the same factor that CC is decreased, the zero frequency will be kept the same, thereby keeping the phase shift the same in the most critical frequency range of the feedback loop. The output voltage settling behavior is related to the stability of the closed-loop system and will demonstrate the actual overall supply performance. 3858fc 25 LTC3858 APPLICATIONS INFORMATION A second, more severe transient is caused by switching in loads with large (>1F) supply bypass capacitors. The discharged bypass capacitors are effectively put in parallel with COUT , causing a rapid drop in VOUT . No regulator can alter its delivery of current quickly enough to prevent this sudden step change in output voltage if the load switch resistance is low and it is driven quickly. If the ratio of CLOAD to COUT is greater than 1:50, the switch rise time should be controlled so that the load rise time is limited to approximately 25 * CLOAD. Thus a 10F capacitor would require a 250s rise time, limiting the charging current to about 200mA. Choosing 0.5% resistors: RA = 24.9k and RB = 77.7k yields an output voltage of 3.296V. The power dissipation on the topside MOSFET can be easily estimated. Choosing a Fairchild FDS6982S dual MOSFET results in: RDS(ON) = 0.035/0.022, CMILLER = 215pF. At maximum input voltage with T(estimated) = 50C: PMAIN = The inductance value is chosen first based on a 30% ripple current assumption. The highest value of ripple current occurs at the maximum input voltage. Tie the FREQ pin to GND, generating 350kHz operation. The minimum inductance for 30% ripple current is: IL = VOUT V 1- OUT ( f ) (L ) VIN A 4.7H inductor will produce 29% ripple current. The peak inductor current will be the maximum DC value plus one half the ripple current, or 5.73A. Increasing the ripple current will also help ensure that the minimum on-time of 95ns is not violated. The minimum on-time occurs at maximum VIN: tON(MIN) = VOUT 3.3V = = 429ns VIN ( f ) 22V ( 350kHz ) 22V ( 5A )2 1+ ( 0.005 ) ( 50C - 25C ) ( 0.035 ) + ( 22V )2 5A 2 ( 2.5 ) ( 215pF ) * 1 1 5V - 2.3V + 2.3V ( 350kHz ) = 331mW Design Example As a design example for one channel, assume VIN = 12V(nominal), VIN = 22V (max), VOUT = 3.3V, IMAX = 5A, VSENSE(MAX) = 75mV and f = 350kHz. 3.3V A short-circuit to ground will result in a folded back current of: ISC = 32mV 1 95ns ( 22V ) - = 2.98A 0.015 2 4.7H with a typical value of RDS(ON) and = (0.005/C)(25C) = 0.125. The resulting power dissipated in the bottom MOSFET is: PSYNC = ( 2.98A ) (1.125) ( 0.022 ) = 220mW 2 which is less than full-load conditions. CIN is chosen for an RMS current rating of at least 3A at temperature assuming only this channel is on. COUT is chosen with an ESR of 0.02 for low output ripple voltage. The output ripple in continuous mode will be highest at the maximum input voltage. The output voltage ripple due to ESR is approximately: VORIPPLE = RESR (IL) = 0.02(1.45A) = 29mVP-P The equivalent RSENSE resistor value can be calculated by using the minimum value for the maximum current sense threshold (64mV): RSENSE 64mV = 0.011 5.73A 3858fc 26 LTC3858 APPLICATIONS INFORMATION PC Board Layout Checklist When laying out the printed circuit board, the following checklist should be used to ensure proper operation of the IC. These items are also illustrated graphically in the layout diagram of Figure 10. Figure 11 illustrates the current waveforms present in the various branches of the 2-phase synchronous regulators operating in the continuous mode. Check the following in your layout: 1. Are the top N-channel MOSFETs MTOP1 and MTOP2 located within 1cm of each other with a common drain connection at CIN? Do not attempt to split the input decoupling for the two channels as it can cause a large resonant loop. 2. Are the signal and power grounds kept separate? The combined IC signal ground pin and the ground return of CINTVCC must return to the combined COUT (-) terminals. The path formed by the top N-channel MOSFET, Schottky diode and the CIN capacitor should have short leads and PC trace lengths. The output capacitor (-) terminals should be connected as close as possible to the (-) terminals of the input capacitor by placing the capacitors next to each other and away from the Schottky loop described above. 3. Do the LTC3858 VFB pins' resistive dividers connect to the (+) terminals of COUT? The resistive divider must be connected between the (+) terminal of COUT and signal ground. The feedback resistor connections should not be along the high current input feeds from the input capacitor(s). 4. Are the SENSE- and SENSE+ leads routed together with minimum PC trace spacing? The filter capacitor between SENSE+ and SENSE- should be as close as possible to the IC. Ensure accurate current sensing with Kelvin connections at the SENSE resistor. 5. Is the INTVCC decoupling capacitor connected close to the IC, between the INTVCC and the power ground pins? This capacitor carries the MOSFET drivers' current peaks. An additional 1F ceramic capacitor placed immediately next to the INTVCC and PGND pins can help improve noise performance substantially. 6. Keep the switching nodes (SW1, SW2), top gate nodes (TG1, TG2), and boost nodes (BOOST1, BOOST2) away from sensitive small-signal nodes, especially from the opposites channel's voltage and current sensing feedback pins. All of these nodes have very large and fast moving signals and therefore should be kept on the "output side" of the LTC3858 and occupy minimum PC trace area. 7. Use a modified "star ground" technique: a low impedance, large copper area central grounding point on the same side of the PC board as the input and output capacitors with tie-ins for the bottom of the INTVCC decoupling capacitor, the bottom of the voltage feedback resistive divider and the SGND pin of the IC. PC Board Layout Debugging Start with one controller on at a time. It is helpful to use a DC-50MHz current probe to monitor the current in the inductor while testing the circuit. Monitor the output switching node (SW pin) to synchronize the oscilloscope to the internal oscillator and probe the actual output voltage as well. Check for proper performance over the operating voltage and current range expected in the application. The frequency of operation should be maintained over the input voltage range down to dropout and until the output load drops below the low current operation threshold--typically 10% of the maximum designed current level in Burst Mode operation. The duty cycle percentage should be maintained from cycle to cycle in a well-designed, low noise PCB implementation. Variation in the duty cycle at a subharmonic rate can suggest noise pickup at the current or voltage sensing inputs or inadequate loop compensation. Overcompensation of the loop can be used to tame a poor PC layout if regulator bandwidth optimization is not required. Only after each controller is checked for its individual performance should both controllers be turned on at the same time. A particularly difficult region of operation is when one controller channel is nearing its current comparator trip point when the other channel is turning on its top MOSFET. This occurs around 50% duty cycle on either channel due to the phasing of the internal clocks and may cause minor duty cycle jitter. 3858fc 27 LTC3858 APPLICATIONS INFORMATION ITH1 SS1 LTC3858 PGOOD2 VFB1 PGOOD1 RPU2 VPULL-UP (<6V) PGOOD2 RPU1 VPULL-UP (<6V) PGOOD1 L1 SENSE1+ TG1 SENSE1- SW1 VOUT1 CB1 FREQ PHASMD RSENSE M1 BOOST1 M2 D1 BG1 CLKOUT PLLIN/MODE RUN1 VIN CVIN RIN GND + INTVCC SENSE2+ BG2 VOUT1 CINTVCC VIN CIN COUT2 1F CERAMIC M3 BOOST2 + EXTVCC SENSE2- VFB2 COUT1 PGND RUN2 SGND 1F CERAMIC + fIN M4 D2 CB2 ITH2 SS2 SW2 RSENSE TG2 VOUT2 L2 3858 F10 Figure 10. Recommended Printed Circuit Layout Diagram Reduce VIN from its nominal level to verify operation of the regulator in dropout. Check the operation of the undervoltage lockout circuit by further lowering VIN while monitoring the outputs to verify operation. Investigate whether any problems exist only at higher output currents or only at higher input voltages. If problems coincide with high input voltages and low output currents, look for capacitive coupling between the BOOST, SW, TG, and possibly BG connections and the sensitive voltage and current pins. The capacitor placed across the current sensing pins needs to be placed immediately adjacent to the pins of the IC. This capacitor helps to minimize the effects of differential noise injection due to high frequency capacitive coupling. If problems are encountered with high current output loading at lower input voltages, look for inductive coupling between CIN, Schottky and the top 3858fc 28 LTC3858 APPLICATIONS INFORMATION SW1 L1 D1 RSENSE1 VOUT1 COUT1 RL1 VIN RIN CIN SW2 BOLD LINES INDICATE HIGH SWITCHING CURRENT. KEEP LINES TO A MINIMUM LENGTH. D2 L2 RSENSE2 VOUT2 COUT2 RL2 3858 F11 Figure 11. Branch Current Waveforms MOSFET components to the sensitive current and voltage sensing traces. In addition, investigate common ground path voltage pickup between these components and the SGND pin of the IC. An embarrassing problem, which can be missed in an otherwise properly working switching regulator, results when the current sensing leads are hooked up backwards. The output voltage under this improper hookup will still be maintained but the advantages of current mode control will not be realized. Compensation of the voltage loop will be much more sensitive to component selection. This behavior can be investigated by temporarily shorting out the current sensing resistor--don't worry, the regulator will still maintain control of the output voltage. 3858fc 29 LTC3858 TYPICAL APPLICATIONS RB1 215k INTVCC CF1 15pF LTC3858 SENSE1+ PGOOD2 C1 1nF RA1 68.1k SENSE1- VFB1 CITH1A 150pF 100k 100k PGOOD1 MBOT1 BG1 SW1 ITH1 RSENSE1 7m CB1 0.47F BOOST1 RITH1 15k CITH1 820pF COUT1 150F VOUT1 3.3V 5A MTOP1 TG1 D1 CSS1 0.1F VIN SS1 INTVCC ILIM PHASMD CLKOUT PGND PLLIN/MODE SGND TG2 EXTVCC RUN1 BOOST2 RUN2 FREQ CIN 22F SS2 SW2 ITH2 BG2 VIN 9V TO 38V CINT 4.7F D2 MTOP2 CB2 0.47F L2 7.2H CSS2 0.1F CITH2 680pF L1 3.3H RSENSE2 10m RITH2 27k CITH2A 100pF RA2 44.2k VOUT2 8.5V COUT2 3A 150F MBOT2 VFB2 SENSE2- C2 1nF CF2 39pF SENSE2+ RB2 422k 3858 F12 COUT1, COUT2: SANYO 10TPD150M L1: SUMIDA CDEP105-3R2M L2: SUMIDA CDEP105-7R2M MTOP1, MTOP2, MBOT1, MBOT2: VISHAY Si7848DP Efficiency vs Output Current Start-Up SW Node Waveforms 100 90 EFFICIENCY (%) 80 70 VOUT = 8.5V VOUT2 2V/DIV VOUT = 3.3V SW1 5V/DIV 60 50 VOUT1 2V/DIV 40 SW2 5V/DIV 30 20 10 VIN = 12V Burst Mode OPERATION 0 0.00001 0.0001 0.001 0.01 0.1 OUTPUT CURRENT (A) 1 10 20ms/DIV 3858 F12c 1s/DIV 3858 F12d 3858 F12b Figure 12. High Efficiency Dual 8.5V/3.3V Step-Down Converter 3858fc 30 LTC3858 TYPICAL APPLICATIONS High Efficiency Dual 2.5V/3.3V Step-Down Converter RB1 143k INTVCC CF1 22pF C1 1nF RA1 68.1k LTC3858 SENSE1+ PGOOD2 SENSE1- VFB1 CITH1A 100pF 100k 100k PGOOD1 MBOT1 BG1 SW1 ITH1 RSENSE1 7m CB1 0.47F BOOST1 RITH1 22k CITH1 820pF COUT1 150F VOUT1 2.5V 5A MTOP1 TG1 D1 CSS1 0.01F VIN SS1 INTVCC ILIM PHASMD CLKOUT PGND PLLIN/MODE SGND TG2 EXTVCC RUN1 BOOST2 RUN2 FREQ CIN 22F SS2 SW2 ITH2 BG2 VIN 4V TO 38V CINT 4.7F D2 MTOP2 CB2 0.47F L2 3.2H CSS2 0.01F CITH2 820pF L1 2.4H RSENSE2 7m RITH2 15k CITH2A 150pF RA2 68.1k VOUT2 3.3V 5A COUT2 150F MBOT2 VFB2 SENSE2- CF2 15pF C2 1nF SENSE2+ RB2 215k 3858 F13 COUT1, COUT2: SANYO 10TPD150M L1: SUMIDA CDEP105-2R5 L2: SUMIDA CDEP105-3R2M MTOP1, MTOP2, MBOT1, MBOT2: VISHAY Si7848DP 3858fc 31 LTC3858 TYPICAL APPLICATIONS High Efficiency Dual 12V/5V Step-Down Converter RB1 422k CF1 33pF RA1 30.1k C1 1nF 100k INTVCC SENSE1+ PGOOD2 SENSE1- PGOOD1 100k VFB1 MBOT1 BG1 CITH1A 100pF SW1 CSS1 0.01F RFREQ 60k D1 LTC3858 VIN SS1 INTVCC ILIM PHASMD CLKOUT PGND PLLIN/MODE SGND TG2 EXTVCC RUN1 BOOST2 RUN2 FREQ CIN 22F SS2 SW2 ITH2 BG2 VIN 12.5V TO 38V CINT 4.7F D2 MTOP2 CB2 0.47F L2 4.3H CSS2 0.01F CITH2 680pF RSENSE2 7m RITH2 17k CITH2A 100pF RA2 75k CF2 15pF VOUT2 5V COUT2 5A 150F MBOT2 VFB2 SENSE2- C2 1nF COUT1 47F VOUT1 12V 3A MTOP1 TG1 ITH1 RSENSE1 10m CB1 0.47F BOOST1 RITH1 33k CITH1 680pF L1 8.8H SENSE2+ COUT1: KEMET T525D476M016E035 COUT2: SANYO 10TPD150M L1: SUMIDA CDEP105-8R8M L2: SUMIDA CDEP105-4R3M MTOP1, MTOP2, MBOT1, MBOT2: VISHAY Si7848DP RB2 393k 3858 TA02a 3858fc 32 LTC3858 TYPICAL APPLICATIONS High Efficiency Dual 24V/5V Step-Down Converter RB1 487k CF1 18pF RA1 16.9k C1 1nF 100k SENSE1+ PGOOD2 SENSE1- PGOOD1 INTVCC 100k MBOT1 BG1 VFB1 CITH1A 100pF VOUT1 24V 1A SW1 CITH1 680pF D1 LTC3858 VIN SS1 INTVCC ILIM PHASMD CLKOUT PGND PLLIN/MODE SGND TG2 EXTVCC RUN1 BOOST2 RUN2 FREQ RFREQ 60k MTOP1 TG1 ITH1 CSS1 0.01F RSENSE1 25m CB1 0.47F BOOST1 RITH1 46k CIN 22F CINT 4.7F SS2 SW2 ITH2 BG2 COUT1 22F x2 CERAMIC VIN 28V TO 38V D2 MTOP2 CB2 0.47F L2 4.3H CSS2 0.01F CITH2 680pF L1 22H RSENSE2 7m VOUT2 5V COUT2 5A 150F RITH2 17k CITH2A 100pF RA2 75k VFB2 SENSE2- CF2 15pF RB2 392k C2 1nF MBOT2 SENSE2+ COUT2: SANYO 10TPD150M L1: SUMIDA CDRH105R-220M L2: SUMIDA CDEP105-4R3M MTOP1, MTOP2, MBOT1, MBOT2: VISHAY Si7848DP 3858 TA04 3858fc 33 LTC3858 TYPICAL APPLICATIONS High Efficiency Dual 1V/1.2V Step-Down Converter RB1 28.7k CF1 56pF RA1 115k C1 1nF 100k INTVCC SENSE1+ PGOOD2 SENSE1- PGOOD1 100k VFB1 L1 MBOT1 0.47H BG1 CITH1A 200pF SW1 CITH1 1000pF CSS1 0.01F RFREQ 60k MTOP1 TG1 ITH1 RSENSE1 4m CB1 0.47F BOOST1 RITH1 3.93k LTC3858 VIN SS1 INTVCC ILIM PHASMD CLKOUT PGND PLLIN/MODE SGND TG2 EXTVCC RUN1 BOOST2 RUN2 FREQ CIN 22F SS2 SW2 ITH2 BG2 VIN 12V CINT 4.7F D2 MTOP2 CB2 0.47F L2 0.47H RSENSE2 4m RITH2 3.93k CITH2A 200pF RA2 115k CF2 56pF MBOT2 VOUT2 1.2V COUT2 8A 220F x2 VFB2 SENSE2- C2 1nF VOUT1 1V 8A D1 CSS2 0.01F CITH2 1000pF COUT1 220F x2 SENSE2+ COUT1, COUT2: SANYO 2R5TPE220M L1: SUMIDA CDEP105-0R4 L2: SUMIDA CDEP105-0R4 MTOP1, MTOP2: RENESAS RJK0305 MBOT1, MBOT2: RENESAS RJK0328 RB2 57.6k 3858 TA03a 3858fc 34 LTC3858 TYPICAL APPLICATIONS High Efficiency Dual 1V/1.2V Step-Down Converter with Inductor DCR Current Sensing RS1 1.18k RB1 28.7k CF1 56pF RA1 115k C1 0.1F INTVCC 100k SENSE1+ PGOOD2 SENSE1- PGOOD1 100k CITH1A 200pF SW1 CITH1 1000pF VIN CIN 22F SS1 INTVCC ILIM PHASMD CLKOUT SGND EXTVCC RUN1 RUN2 FREQ RFREQ 65k VIN 12V CINT 4.7F PGND D2 MTOP2 TG2 BOOST2 CB2 0.47F L2 0.47H CSS2 0.01F SS2 SW2 ITH2 BG2 RITH2 3.93k CITH2A 220pF RA2 115k CF2 56pF RB2 57.6k MBOT2 VOUT2 1.2V COUT2 8A 220F x2 VFB2 SENSE2- C2 0.1F VOUT1 1V 8A D1 LTC3858 CSS1 0.01F MTOP1 TG1 ITH1 COUT1 220F x2 CB1 0.47F BOOST1 RITH1 3.93k CITH2 1000pF L1 0.47H MBOT1 BG1 VFB1 SENSE2+ COUT1, COUT2: SANYO 2R5TPE220M L1, L2: VISHAY IHL P2525CZERR47M06 MTOP1, MTOP2: RENESAS RJK0305 MBOT1, MBOT2: RENESAS RJK0328 RS2 1.18k 3858 TA05 3858fc 35 LTC3858 PACKAGE DESCRIPTION UH Package 32-Lead Plastic QFN (5mm x 5mm) (Reference LTC DWG # 05-08-1693 Rev D) 0.70 p0.05 5.50 p0.05 4.10 p0.05 3.45 p 0.05 3.50 REF (4 SIDES) 3.45 p 0.05 PACKAGE OUTLINE 0.25 p 0.05 0.50 BSC RECOMMENDED SOLDER PAD LAYOUT APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 5.00 p 0.10 (4 SIDES) BOTTOM VIEW--EXPOSED PAD 0.75 p 0.05 R = 0.05 TYP 0.00 - 0.05 PIN 1 NOTCH R = 0.30 TYP OR 0.35 s 45o CHAMFER R = 0.115 TYP 31 32 0.40 p 0.10 PIN 1 TOP MARK (NOTE 6) 1 2 3.50 REF (4-SIDES) 3.45 p 0.10 3.45 p 0.10 (UH32) QFN 0406 REV D 0.200 REF NOTE: 1. DRAWING PROPOSED TO BE A JEDEC PACKAGE OUTLINE M0-220 VARIATION WHHD-(X) (TO BE APPROVED) 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 0.25 p 0.05 0.50 BSC 3858fc 36 LTC3858 REVISION HISTORY REV DATE DESCRIPTION A 12/09 Change to Absolute Maximum Ratings PAGE NUMBER Change to Electrical Characteristics Change to Typical Performance Characteristics Change to Pin Functions Text Changes to Operation Section Text Changes to Applications Information Section 08/10 C 12/10 2, 3, 4 6 8, 9 11, 12, 13 21, 22, 23, 24, 26 Change to Table 2 23 Change to Figure 10 28 Changes to Related Parts B 2 Changes to Electrical Characteristics 38 2, 3, 4 Added Typical Application to Back Page and Updated Related Parts 38 Changes to Electrical Characteristics 3 Changes to Functional Diagram 10 Changes to Typical Applications 30 to 35, 38 3858fc Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 37 LTC3858 TYPICAL APPLICATION High Efficiency 2-Phase 12V/150W Step-Down Converter RB1 698k CF1 10pF RA1 49.9k C1 1nF 100k SENSE1+ PGOOD2 SENSE1- PGOOD1 INTVCC 100k VFB1 MBOT1 BG1 CITH1A 68pF L1 6H 10F 16V SW1 CITH1 3300pF CSS1 0.1F VOUT SS1 ITH1 VFB1 LTC3858 VIN SS1 INTVCC ILIM PHASMD CLKOUT PGND PLLIN/MODE SGND TG2 EXTVCC RUN1 BOOST2 RUN2 FREQ SW2 SS2 ITH2 VOUT1 12V 12.5A D1 CIN 10F 50V CINT 4.7F 10F 50V VIN 19V TO 28V D2 MTOP2 CB2 0.47F L2 6H RSENSE2 5m COUT2 22F 16V MBOT2 BG2 VFB2 SENSE2- C2 1nF MTOP1 TG1 ITH1 RSENSE1 5m CB1 0.47F BOOST1 RITH1 2.94k COUT1 22F 16V SENSE2+ 10F 16V COUT1, COUT2: SANYO 16TQC22M L1, L2: SUMIDA CDEP106-6ROM MTOP1, MTOP2: INFINEON BSZ097N04LS MBOT1, MBOT2: INFINEON BSZ097N04LS 3858 TA06 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC3859 Low IQ, Triple Output Buck/Buck/Boost Synchronous Outputs (5V) Remain in Regulation Through Cold Crank 2.5V VIN 38V, DC/DC Controller VOUT(BUCKS) Up to 24V, VOUT(BOOST) Up to 60V, IQ = 55A, LTC3868/LTC3868-1 Low IQ, Dual Output 2-Phase Synchronous StepDown DC/DC Controllers with 99% Duty Cycle Phase-Lockable Fixed Operating Frequency 50kHz to 900kHz, 4V VIN 24V, 0.8V VOUT 14V, IQ = 170A LTC3857/LTC3857-1 Low IQ, Dual Output 2-Phase Synchronous StepDown DC/DC Controllers with 99% Duty Cycle Phase-Lockable Fixed Operating Frequency 50kHz to 900kHz, 4V VIN 38V, 0.8V VOUT 24V, IQ = 50A, LTC3890/LTC3890-1 60V, Low IQ, Dual 2-Phase Synchronous Step-Down DC/DC Controller with 99% Duty Cycle Phase-Lockable Fixed Operating Frequency 50kHz to 900kHz, 4V VIN 60V, 0.8V VOUT 24V, IQ = 50A, LTC3834/LTC3834-1 Low IQ, Synchronous Step-Down DC/DC Controllers Phase-Lockable Fixed Operating Frequency 140kHz to 650kHz, 4V VIN 36V, 0.8V VOUT 10V, IQ = 30A, LTC3835/LTC3835-1 Low IQ, Synchronous Step-Down DC/DC Controllers Phase-Lockable Fixed Operating Frequency 140kHz to 650kHz, 4V VIN 36V, 0.8V VOUT 10V, IQ = 80A, LT3845A Low IQ, High Voltage Synchronous Step-Down DC/DC Controller Adjustable Fixed Operating Frequency 100kHz to 500kHz, 4V VIN 60V, 1.23V VOUT 36V, IQ = 120A, TSSOP-16 LTC3824 Low IQ, High Voltage DC/DC Controller, 100% Duty Cycle Selectable Fixed 200kHz to 600kHz Operating Frequency 4V VIN 60V, 0.8V VOUT VIN, IQ = 40A, MSOP-10E 3858fc 38 Linear Technology Corporation LT 1210 REV C * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com (c) LINEAR TECHNOLOGY CORPORATION 2009