Features Description GM66102 of positive fixed and adjustable regulators is de- Fixed and Adjustable Voltage Versions signed to provide up to 1A output with high current, high ac- Output Current up to 1A curacy, and extremely low dropout voltage performance. Low Dropout Voltage 350mV @ 1A These regulators feature 300 to 350mV (full load) dropout voltages and very low ground current. Although designed for high current, and loads, these devices are also useful in lower current, extremely low dropout-critical systems, Low Ground Current Accurate 1% Guaranteed Tolerance Extremely Fast Transient Response where their minimal dropout voltage and ground current val- Reverse-battery Protection ues are important characteristics. "Load Dump" Protection GM66102 is fully protected against overcurrent, reversed Extremely Fast Transient Response input polarity (or reversed battery connection), reversed lead insertion, over-temperature operation, and transient voltage spikes (positive or negative). GM66102 is available in TO-220, SOT-223, TO-252 and TO-263 packages. Application High Efficiency Linear Regulators Battery Powered Equipment Post Regulators for Switching Supplies Automotive Electronics TYPICAL APPLICATION CIRCUITS CIN VIN + 22F GM66102 - 2.5 GND 2.5V 1% @1A VOUT + 33F GM 431 CIN is required if regulator is located an appreciable distance from power supply filter. www.gammamicro.com GM66102 V0.1 3.3V 5% 1 MARKING INFORMATION & PIN CONFIGURATIONS(TOP VIEW) 2 TO-220 TO-263-2 (D PAK) GND GM66102 GM66102 VVAYWW VVAYWW GM66102 TO-252 (DPAK) GND VVAYWW VIN VOUT GND VOUT GND VIN VIN VOUT GND SOT-223 GND V V / VVV A Y WW GM66102 VVAYWW = Output Voltage (33=3.3V , 120=12V) = Assembly Location = Year = Weekly VOUT GND VIN GM66102 ORDERING INFORMATION 2 Package Shipping Ordering Number Output Voltage GM66102-1.5TB3T 1.5V TO-220 50 Units/ Tube GM66102-1.5ST3T 1.5V SOT-223 80 Units/ Tube GM66102-1.5ST3R 1.5V SOT-223 2,500 Units/ Tape & Reel GM66102-1.5TC3T 1.5V TO-252 80 Units / Tube GM66102-1.5TC3R 1.5V TO-252 2,500 Units/ Tape & Reel GM66102-1.5TA3T 1.5V TO-263-2 50 Units / Tube GM66102-1.5TA3R 1.5V TO-263-2 800 Units/ Tape & Reel GM66102-1.8TB3T 1.8V TO-220 50 Units/ Tube GM66102-1.8ST3T 1.8V SOT-223 80 Units/ Tube GM66102-1.8ST3R 1.8V SOT-223 2,500 Units/ Tape & Reel GM66102-1.8TC3T 1.8V TO-252 80 Units / Tube GM66102-1.8TC3R 1.8V TO-252 2,500 Units/ Tape & Reel GM66102-1.8TA3T 1.8V TO-263-2 50 Units / Tube GM66102-1.8TA3R 1.8V TO-263-2 800 Units/ Tape & Reel GM66102-2.5TB3T 2.5V TO-220 50 Units/ Tube GM66102-2.5ST3T 2.5V SOT-223 80 Units/ Tube GM66102-2.5ST3R 2.5V SOT-223 2,500 Units/ Tape & Reel GM66102-2.5TC3T 2.5V TO-252 80 Units / Tube GM66102-2.5TC3R 2.5V TO-252 2,500 Units/ Tape & Reel GM66102-2.5TA3T 2.5V TO-263-2 50 Units / Tube GM66102-2.5TA3R 2.5V TO-263-2 800 Units/ Tape & Reel * For detail Ordering Number identification, please see last page. ORDERING INFORMATION (Continued) Ordering Number Output Voltage GM66102-3.0TB3T 3.0V TO-220 50 Units/ Tube GM66102-3.0ST3T 3.0V SOT-223 80 Units/ Tube GM66102-3.0ST3R 3.0V SOT-223 2,500 Units/ Tape & Reel GM66102-3.0TC3T 3.0V TO-252 80 Units / Tube GM66102-3.0TC3R 3.0V TO-252 2,500 Units/ Tape & Reel GM66102-3.0TA3T 3.0V TO-263-2 50 Units / Tube GM66102-3.0TA3R 3.0V TO-263-2 800 Units/ Tape & Reel GM66102-3.3TB3T 3.3V TO-220 50 Units/ Tube GM66102-3.3ST3T 3.3V SOT-223 80 Units/ Tube GM66102-3.3ST3R 3.3V SOT-223 2,500 Units/ Tape & Reel GM66102-3.3TC3T 3.3V TO-252 80 Units / Tube GM66102-3.3TC3R 3.3V TO-252 2,500 Units/ Tape & Reel GM66102-3.3TA3T 3.3V TO-263-2 50 Units / Tube GM66102-3.3TA3R 3.3V TO-263-2 800 Units/ Tape & Reel GM66102-5.0TB3T 5.0V TO-220 50 Units/ Tube GM66102-5.0ST3T 5.0V SOT-223 80 Units/ Tube GM66102-5.0ST3R 5.0V SOT-223 2,500 Units/ Tape & Reel GM66102-5.0TC3T 5.0V TO-252 80 Units / Tube GM66102-5.0TC3R 5.0V TO-252 2,500 Units/ Tape & Reel GM66102-5.0TA3T 5.0V TO-263-2 50 Units / Tube GM66102-5.0TA3R 5.0V TO-263-2 800 Units/ Tape & Reel GM66102-12TB3T 12V TO-220 GM66102-12ST3T 12V SOT-223 80 Units/ Tube GM66102-12ST3R 12V SOT-223 2,500 Units/ Tape & Reel GM66102-12TC3T 12V TO-252 80 Units / Tube GM66102-12TC3R 12V TO-252 2,500 Units/ Tape & Reel GM66102-12TA3T 12V TO-263-2 50 Units / Tube GM66102-12TA3R 12V TO-263-2 800 Units/ Tape & Reel Package Shipping 50 Units/ Tube GM66102 * For detail Ordering Number identification, please see last page. 3 ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL Value UNIT Power Dissipation PD Internally limited W Input Supply Voltage (Note 1.) VIN -20 to +60 V Lead Temperature (Soldering, 5 sec ) TLEAD 260 C Storage Temperature Range TSTG -65 to +150 C OPERATING RATINGS SYMBOL Value UNIT Maximum Operating Input Voltage VIN 26 V Operating Junction Temperature Range TJ -40 to +125 C Thermal Resistance (Junction to case) TO- 223 TO- 252 TO- 263 TO- 220 RqJC PARAMETER 15 6.0 2.0 2.0 C/W BLOCK DIAGRAM VIN VOUT O.V. ILimit 28V Ref. 1.24V R1 + GM66102 - 4 Thermal Shut-down R2 GND ELECTRICAL CHARACTERISTICS (TA = 25C unless otherwise noted) Unless otherwise specified: TJ = 25C; Bold values are guaranteed across the operating temperature range. Unit -1 1 % -2 2 % Conditions Min Output Voltage (Note2) IO = 10 mA 10mA IO IFL , (VOUT + 1V) VIN 26V Typ Max Parameter Line Regulation IO = 10mA, (VOUT + 1V) VIN 26V 0.06 0.5 % Load Regulation VIN = VOUT + 5V, 10mA IOUT IFL 0.20 1.0 % DVOUT/ DT 20 100 ppm/C DVOUT = -1% (Note 3) IO = 100mA IO = 750mA IO = 1.0A 80 220 300 200 mV Output Voltage change with Temperature Coef. (Note 6) Dropout Voltage 500 (For 1.50 Version) IO = 100mA IO = 1.0A 0.6 0.8 V (For 1.80 Version) IO = 100mA IO = 1.0A 0.3 0.5 V 20 mA Ground Current Ground Pin Current at Dropout IGNDDO Current Limit Output Noise Voltage en, (10Hz to 100Hz) IO = 100mA IO = 750mA, VIN = VOUT + 1V IO = 1.0A 8 22 VIN = 0.5V less than specified VOUT, IOUT = 10mA, (Note 5) 0.9 VOUT,= 0V (Note 4) 2.1 CL = 10F CL = 33F 400 260 mA 3.5 A V (rms) GM66102 Note 1: Maximum positive supply voltage of 60V must be of limited duration (<100msec) and duty cycle ( 1%). The maximum continuous supply voltage is 26V. Note 2: Full Load current (IFL) is defined as 1.0A for the GM66102 series. Note 3: Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with VOUT + 1V applied to VIN Note 4: VIN = VOUT (nominal) + 1V. For example, use VIN = 4.3V for a 3.3V regulator or use 6V for a 5V regulator. Employ pulse-testing procedures to minimize temperature rise. Note 5: Ground pin current is the regulator quiescent current. The total current drawn from the source is the sum of the load current plus the ground pin current. Note 6: Output voltage temperature coefficient is defined as the worst case voltage change divided by the total temperature range. 5 TYPICAL CHARACTERISTICS GM66102 450 5.0 1.2 4.0 1.0 VOUT = 5V ILOAD = 10mA 300 250 200 150 100 3.0 Ground Current (mA) 350 Output Voltage (V) Dropout Voltage (mV) 400 IOUT = 10mA IOUT = 1.0A 2.0 1.0 0.8 0.6 0.4 0.2 50 0 0.0 0.5 1.0 0 0 1.5 5 6 0 2 4 6 8 10 Figure 2. GM66102 Dropout Voltage vs. Output Current Figure 3. GM66102-5.0 Dropout Characteristics Figure 4. GM66102 Ground Current vs. Supply Voltage 300 GM66102 IOUT = 1.0A 2.5 250 40 30 20 2.0 Ground Current (mA) Ground Current (A) Ground Current (mA) 4 Supply Voltage (V) 10 200 ILOAD = 10mA 150 100 1.5 ILOAD = 250mA 1.0 0.5 50 0 0 2 4 6 8 10 Supply Voltage (V) Figure 5. GM66102 Ground Current vs. Supply Voltage 3.40 3.38 3.36 Output Voltage (V) 3 Input Voltage(V) 50 3.34 3.32 3.30 3.28 3DEVICES 3.26 3.24 3.22 3.20 -60 -30 0 30 60 90 120 150 Temperature (C) GM66102 2 Output Current (A) 60 6 0 1 Figure 8. GM66102-3.3 Output Voltage vs. Temperature 0 -60 -30 0 30 60 90 120 130 0 -60 -30 0 30 60 90 120 150 Temperature (C) Temperature (C) Figure 6. GM66102 Ground Current vs. Temperature Figure 7. GM66102 Ground Current vs. Temperature APPLICATION INFORMATION Thermal Design GM66102 series is high performance whit low-dropout Linear regulators are simple to use. The most com- voltage regulators, suitable for all moderate to high- plicated design parameters to consider are thermal current voltage regulator applications. Their 350mV characteristics. Thermal design requires the follow- dropout voltage at full load makes them especially valu- ing application-specific parameters: Maximum ambient temperature, TA Output Current, IOUT Output Voltage, VOUT Input Voltage, VIN able in battery powered systems and as high efficiency noise filters in "post-regulator" applications. Unlike older NPN-pass transistor designs, where the minimum dropout voltage is limited by the base-emitter voltage drop and collector-emitter saturation voltage, dropout performance of the PNP output of these devices is limited merely by the low VCE saturation voltage. A trade- First, we calculate the power dissipation of the regulator from these numbers and the device parameters from this formula: PD = IOUT (1.01VIN - VOUT) off for the low dropout voltage is a varying base drive requirement. But, Gamma's PNP process reduces this drive requirement to merely 1% of the load current. where the ground current is approximated by 1% of IOUT. The GM66102 series of regulators are fully protected from damage due to fault conditions. Current limiting is Then the heat sink thermal resistance is determined with this formula: provided. This limiting is linear and output current under overload conditions is constant. Thermal shutdown RqSA = disables the device when the die temperature exceeds TJ(MAX) - TA PD (RqJC + RqCS) the 125C maximum safe operating temperature. Transient protection allows device (and load) survival even when the input voltage spikes between -20V and where TJ(MAX) 125C and RqCS is between 0 and 2C/W. +60V. When the input voltage exceeds about 35V to 40V, the overvoltage sensor temporarily disables the regulator. The output structure of these regulators allows voltages in excess of the desired output voltage to be applied without reverse current flow. An additional feature of this regulator family is a common pinout: a design's current requirement may change up or down by yet use the same board layout, as all of these regu- The heat sink may be significantly reduced in applications where the minimum input voltage is known and is large compared with the dropout voltage. Use a series input resistor to drop excessive voltage and distribute the heat between this resistor and the regulator, the low dropout properties of Gamma PNP regulators allow very significant reductions in regulator power dissipation and the associated heat sink with- lators have identical pinouts. out compromising performance. When this tech- + VOUT VOUT VIN GND nique is employed, a capacitor of at least 0.1F is needed directly between the input and regulator + Figure 9. Linear regulators require only two capacitors for operation. ground. GM66102 VIN 7 TO-252 PACKAGE OUTLINE DIMENSIONS 6.50 0.05 2.30 0.05 Pad Layout 5.340 0.05 0.508 0.0127 29 0.5 REF 0.6 7 0.244 6.20 1.0 0.05 0.118 3.0 6.10 0.05 0.070 0.05 7.20 0.05 9.900 0.75 0.10 0.243 6.172 0.228 5.80 7 7 0.75 0.10 2.70 0.10 0.89 0.05 1.525 0.10 R 0.25 0.13 0.81 0.038 0.063 1.6 0.101 2.58 ( Inches ) mm Unit: mm R0.15 max 2 TO-263-2 PACKAGE OUTLINE DIMENSIONS 9.90 0.20 4.50 0.20 +0.1 1.30 -0.05 15 0.40 1.20 Pad Layout 3 1.50 DP0.20 0.63 17.02 0.33 8.38 9.20 0.20 15.3 0.20 0.10 0.01 3 3 1.4 0.20 R0.30 2.40 0.20 2.00 0.10 4.90 0.20 1.27 0.10 GM66102 2.54 TYP (2.54 0.20) 8 0.42 10.66 +0.1 0.50 -0.05 0.04 1.016 10.0 0.20 7.0 4.0 0.40 3 3 0.24 6.096 2.54 0.10 0.75 R0.30 0.90 0.10 0.12 3.05 ( 0.90 R 0.3 R 0.45 7.2 9.20 0.20 10.00 0.20 4.90 0.20 Unit: mm Inches ) mm TO-220 PACKAGE OUTLINE DIMENSIONS 4.50 0.20 9.90 0.20 3.60 0.20 8.0 8.70 2.80 0.10 7.0 +0.1 1.30 -0.05 4.60 8.40 3 45 3.00 1.27 0.10 2.54 TYP (2.54 0.20) 3 0.9 7.0 3 3-R0.2 10.08 0.30 13.08 0.20 1.46 1.00 3 18.95 MAX 3.70 0.20 15.90 0.20 1.50 DP0.20 9.20 0.20 1.30 0.10 1.70 +0.1 0.80 0.10 1.52 0.10 0.50 -0.05 2.40 0.20 3 2 - R 0.3 Unit: mm 10.00 0.20 SOT- 223 PACKAGE OUTLINE DIMENSIONS 1.80max 0.3 0.05 3.0 0.05 1.75 0.10 0.65 0.10 0.60 0.06 0.04 3.5 0.10 Pad Layout 0.15 3.8 7.0 0.15 1.75 0.10 0~0.075 0~10 2.30TYP 0.95TYP 4.6 0.1 0.091 2.3 0.70 0.05 0.248 6.3 0.091 2.3 0.079 2.0 13 0.059 1.5 0.84 1.6 0.10 0.46 13 Unit: mm 6.50 0.10 0.059 1.5 0.059 1.5 Inches mm GM66102 0.079 2.0 9 ORDERING NUMBER GM 66102 1.5 TB3 T Gamma Micro. Circuit Type GM66102 Output Voltage 1.5: 1.5V 1.8: 1.8V 2.5: 2.5V 3.0: 3.0V 3.3: 3.3V 5.0: 5.0V 12: 12V 10 Shipping R: Tape & Reel T: Tube Package TA3: TO-263 TB3: TO-220 TC3: TO-252 ST3: SOT-223 11 GM66102