FUJITSU SEMICONDUCTOR DATA SHEET DS07-13748-1E 16-bit Proprietary Microcontroller CMOS F2MC-16LX MB90860E Series MB90867E(S), MB90F867E(S), MB90V340E-101/102 DESCRIPTION MB90860E-series with Flash ROM is especially designed for automotive and other industrial applications. With the new 0.35 m CMOS technology, Fujitsu now offers on-chip Flash ROM program memory up to 512 Kbytes. The power supply (3 V) is supplied to the internal MCU core from an internal regulator circuit. This creates a major advantage in terms of EMI and power consumption. The internal PLL clock frequency multiplier provides an internal 42 ns instruction cycle time from an external 4 MHz clock. The unit features an 8 channel Output Compare Unit and 8 channel Input Capture Unit with 2 separate 16-bit free running timers. 4 UARTs constitute additional functionality for communication purposes. Note : F2MC is the abbreviation of FUJITSU Flexible Microcontroller. Be sure to refer to the "Check Sheet" for the latest cautions on development. "Check Sheet" is seen at the following support page URL : http://www.fujitsu.com/global/services/microelectronics/product/micom/support/index.html "Check Sheet" lists the minimal requirement items to be checked to prevent problems beforehand in system development. Copyright(c)2006 FUJITSU LIMITED All rights reserved MB90860E Series FEATURES * CPU * Instruction system best suited to controller * Wide choice of data types (bit, byte, word, and long word) * Wide choice of addressing modes(23 types) * Enhanced multiply-divide instructions and RETI instructions * Enhanced high-precision computing with 32-bit accumulator * Instruction system compatible with high-level language (C language) and multitask * Employing system stack pointer * Enhanced various pointer indirect instructions * Barrel shift instructions * Increased processing speed * 4-byte instruction queue * Serial interface * UART (LIN/SCI) : up to 4 channels * Equipped with full-duplex double buffer * Clock-asynchronous or clock-synchronous serial transmission is available * I2C interface* : up to 2 channels * Up to 400 Kbits/s transfer rate * Interrupt controller * Powerful interrupt function * Powerful 8-level, 34-condition interrupt feature * Up to 16 external interrupts are supported * Automatic data transfer function independent of CPU * Expanded intelligent I/O service function (EI2OS) : up to 16 channels * I/O port * General-purpose input/output port (CMOS output) - 80 ports (devices without S-suffix) - 82 ports (devices with S-suffix) * 8/10-bit A/D converter * 8/10-bit A/D converter : 24 channels * Resolution is selectable between 8-bit and 10-bit. * Activation by external trigger input is allowed. * Conversion time : 3 s (at 24-MHz machine clock, including sampling time) * Program patch function * Timer * Time-base timer, clock timer, watchdog timer : 1 channel * 8/16-bit PPG timer : 8-bit x 16 channels, or 16-bit x 8 channels * 16-bit reload timer : 4 channels * 16-bit input/output timer - 16-bit free run timer : 2 channel (FRT0 : ICU 0/1/2/3, OCU 0/1/2/3, FRT1 : ICU 4/5/6/7, OCU 4/5/6/7) - 16-bit input capture: (ICU) : 8 channels - 16-bit output compare : (OCU) : 8 channels 2 MB90860E Series * Variety of mode * Low power consumption (standby) mode * Sleep mode (a mode that halts CPU operating clock) * Main timer mode (time-base timer mode that is transferred from main clock mode) * PLL timer mode (time-base timer mode that is transferred from PLL clock mode) * Watch mode (a mode that operates sub clock and clock timer only) * Stop mode (a mode that stops oscillation clock and sub clock) * CPU blocking operation mode * Technology * 0.35 m CMOS technology * : I2C license : Purchase of Fujitsu I2C components conveys a license under the Philips I2C Patent Rights to use, these components in an I2C system provided that the system conforms to the I2C Standard Specification as defined by Philips. 3 MB90860E Series PRODUCT LINEUP Part Number MB90867E(S) MB90F867E(S) MB90V340E-101/102 Parameter F2MC-16LX CPU CPU Type System clock MASK ROM product Flash memory product Evaluation product On-chip PLL clock multiplier (x1, x2, x3, x4, x6, 1/2 when PLL stops) Minimum instruction execution time : 42 ns (4 MHz osc. PLL x 6) ROM MASK ROM 128 Kbytes Flash memory 128 Kbytes External RAM 6 Kbytes 6 Kbytes 30 Kbytes Emulator-specific power supply*1 Yes Technology 0.35 m CMOS with on-chip 0.35 m CMOS with on-chip voltage regulator for internal 0.35 m CMOS with on-chip voltage regulator for internal power supply + Flash memory voltage regulator for internal power supply with on-chip charge pump for power supply programming voltage Operating voltage range 3.5 V to 5.5 V : at normal operating (not using A/D converter) 4.0 V to 5.5 V : at using A/D converter/Flash programming 4.5 V to 5.5 V : at using external bus 5 V 10% -40 C to +105 C QFP-100, LQFP-100 PGA-299 4 channels 5 channels Temperature range Package UART I2C (400 kbps) 8/10-bit A/D converter Wide range of baud rate settings using a dedicated reload timer Special synchronous options for adapting to different synchronous serial protocols LIN functionality working either as master or slave LIN device 2 channels 24 channels 10-bit or 8-bit resolution Conversion time : Min 3 s include sample time (per one channel) 16-bit reload timer (4 channels) Operation clock frequency : fsys/21, fsys/23, fsys/25 (fsys = Machine clock frequency) Supports External Event Count function 16-bit I/O timer (2 channels) Signals an interrupt when overflowing Supports Timer Clear when a match with Output Compare (ch.0, ch.4) Operation clock freq. : fsys, fsys/21, fsys/22, fsys/23, fsys/24, fsys/25, fsys/26, fsys/27 (fsys = Machine clock freq.) I/O Timer 0 (clock input FRCK0) corresponds to ICU 0/1/2/3, OCU 0/1/2/3 I/O Timer 1 (clock input FRCK1) corresponds to ICU 4/5/6/7, OCU 4/5/6/7 16-bit output compare (8 channels) Signals an interrupt when 16-bit I/O Timer match output compare registers. A pair of compare registers can be used to generate an output signal. 16-bit input capture (8 channels) Rising edge, falling edge or rising & falling edge sensitive Signals an interrupt upon external event (Continued) 4 MB90860E Series (Continued) Part Number MB90867E(S) MB90F867E(S) MB90V340E-101/102 Parameter Supports 8-bit and 16-bit operation modes Sixteen 8-bit reload counters 8/16-bit Sixteen 8-bit reload registers for L pulse width programmable pulse Sixteen 8-bit reload registers for H pulse width generator A pair of 8-bit reload counters can be configured as one 16-bit reload counter or as (8 channels) 8-bit prescaler plus 8-bit reload counter Operation clock freq. : fsys, fsys/21, fsys/22, fsys/23, fsys/24 or 128 s@fosc = 4 MHz (fsys = Machine clock frequency, fosc = Oscillation clock frequency) CAN interface External interrupt (16 channels) 3 channels Can be used rising edge, falling edge, starting up by H/L level input, external interrupt, expanded intelligent I/O services (EI2OS) and DMA D/A converter 2 channels Up to 100 kHz sub clock for low power operation Devices without `S'-suffix I/O ports Virtually all external pins can be used as general purpose I/O port All push-pull outputs Bit-wise settable as input/output or peripheral signal Settable in pin-wise of 8 as CMOS schmitt trigger/automotive inputs (default) TTL input level settable for external bus (32-pin only for external bus) Flash memory Supports automatic programming, Embedded AlgorithmTM*2 Write/Erase/Erase-Suspend/Resume commands A flag indicating completion of the algorithm Number of erase cycles : 10,000 times Data retention time : 20 years Boot block configuration Erase can be performed on each block Block protection with external programming voltage Flash Security Feature for protecting the content of the Flash Only for MB90V340E102 *1 : It is setting of Jumper switch (TOOL VCC) when Emulator (MB2147-01) is used. Please refer to the Emulator hardware manual about details. *2 : Embedded Algorithm is a trade mark of Advanced Micro Devices Inc. 5 MB90860E Series PIN ASSIGNMENTS * MB90V340E-101/102 P03/AD03/INT11 P02/AD02/INT10 P01/AD01/INT9 P00/AD00/INT8 PA1/TX0 PA0/RX0/INT8R P97/OUT3 P96/OUT2 P95/OUT1 P94/OUT0 P93/PPG7(6) P92/PPG5(4) P91/PPG3(2) P90/PPG1(0) Vss Vcc P87/SCK1 P86/SOT1 P85/SIN1 P84/SCK0/INT15R P83/SOT0/TOT2 P82/SIN0/TIN2/INT14R P81/TOT0/CKOT/INT13R P80/TIN0/ADTG/INT12R P77/AN23/INT7 P76/AN22/INT6 RST MD0 MD1 MD2 (TOP VIEW) P24/A20/IN0 P25/A21/IN1 P26/A22/IN2 P27/A23/IN3 P30/ALE/IN4 X1 X0 P15/AD13/SIN4 P16/AD14/SOT4 P17/AD15/SCK4 P20/A16/PPG9(8) P21/A17/PPGB(A) P22/A18/PPGD(C) P23/A19/PPGF(E) P75/AN21/INT5 P74/AN20/INT4 P73/AN19/INT3 P72/AN18/INT2 P71/AN17/INT1 P70/AN16/INT0 Vss P67/AN7/PPGE(F) P66/AN6/PPGC(D) P65/AN5/PPGA(B) P64/AN4/PPG8(9) P63/AN3/PPG6(7) P62/AN2/PPG4(5) P61/AN1/PPG2(3) P60/AN0/PPG0(1) AVss AVRL AVRH AVcc P57/AN15/DA01 P35/HAK/OUT5 P36/RDY/OUT6 P37/CLK/OUT7 P40/X0A* P41/X1A* Vcc Vss C P42/IN6/RX1/INT9R P43/IN7/TX1 P44/SDA0/FRCK0 P45/SCL0/FRCK1 P46/SDA1 P47/SCL1 P50/AN8/SIN2 P51/AN9/SOT2 P52/AN10/SCK2 P53/AN11/TIN3 P54/AN12/TOT3 P55/AN13 P56/AN14/DA00 Vcc Vss 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 81 82 49 83 48 84 47 85 46 86 45 87 44 88 43 89 42 90 41 QFP - 100 91 40 92 39 93 38 94 37 95 36 96 35 97 34 98 33 99 32 100 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 P31/RD/IN5 P32/WRL/WR/RX2/INT10R P33/WRH/TX2 P34/HRQ/OUT4 P04/AD04/INT12 P05/AD05/INT13 P06/AD06/INT14 P07/AD07/INT15 P10/AD08/TIN1 P11/AD09/TOT1 P12/AD10/SIN3/INT11R P13/AD11/SOT3 P14/AD12/SCK3 (FPT-100P-M06) * : X0A, X1A : MB90V340E-102 P40, P41 : MB90V340E-101 (Continued) 6 MB90860E Series (Continued) RST MD0 MD1 MD2 P75/AN21/INT5 P74/AN20/INT4 P73/AN19/INT3 P72/AN18/INT2 P71/AN17/INT1 P70/AN16/INT0 Vss P67/AN7/PPGE(F) P66/AN6/PPGC(D) P65/AN5/PPGA(B) P64/AN4/PPG8(9) P63/AN3/PPG6(7) P62/AN2/PPG4(5) P61/AN1/PPG2(3) P60/AN0/PPG0(1) AVss AVRL AVRH AVcc P57/AN15/DA01 P56/AN14/DA00 P55/AN13 P54/AN12/TOT3 P42/IN6/RX1/INT9R P43/IN7/TX1 P44/SDA0/FRCK0 P45/SCL0/FRCK1 P46/SDA1 P47/SCL1 P50/AN8/SIN2 P51/AN9/SOT2 P52/AN10/SCK2 P53/AN11/TIN3 Vcc Vss C P35/HAK/OUT5 P36/RDY/OUT6 P37/CLK/OUT7 P40/X0A* P41/X1A* 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 76 50 77 49 78 48 47 79 46 80 45 81 44 82 43 83 42 84 41 85 40 86 39 87 38 88 LQFP - 100 37 89 36 90 35 91 34 92 33 93 32 94 31 95 30 96 29 97 98 28 99 27 100 26 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 P26/A22/IN2 P27/A23/IN3 P30/ALE/IN4 P31/RD/IN5 P32/WRL/WR/RX2/INT10R P33/WRH/TX2 P34/HRQ/OUT4 P01/AD01/INT9 P02/AD02/INT10 P03/AD03/INT11 P04/AD04/INT12 P05/AD05/INT13 P06/AD06/INT14 P07/AD07/INT15 P10/AD08/TIN1 P11/AD09/TOT1 P12/AD10/SIN3/INT11R P13/AD11/SOT3 P14/AD12/SCK3 Vcc Vss X1 X0 P15/AD13/SIN4 P16/AD14/SOT4 P17/AD15/SCK4 P20/A16/PPG9(8) P21/A17/PPGB(A) P22/A18/PPGD(C) P23/A19/PPGF(E) P24/A20/IN0 P25/A21/IN1 P81/TOT0/CKOT/INT13R P80/TIN0/ADTG/INT12R P77/AN23/INT7 P76/AN22/INT6 P00/AD00/INT8 PA1/TX0 PA0/RX0/INT8R P97/OUT3 P96/OUT2 P95/OUT1 P94/OUT0 P93/PPG7(6) P92/PPG5(4) P91/PPG3(2) P90/PPG1(0) Vss Vcc P87/SCK1 P86/SOT1 P85/SIN1 P84/SCK0/INT15R P83/SOT0/TOT2 P82/SIN0/TIN2/INT14R (TOP VIEW) (FPT-100P-M05) * : X0A, X1A : MB90V340E-102 P40, P41 : MB90V340E-101 7 MB90860E Series * MB90867E(S)/MB90F867E(S) RST MD2 P75/AN21/INT5 P74/AN20/INT4 P73/AN19/INT3 P72/AN18/INT2 P71/AN17/INT1 P70/AN16/INT0 Vss P67/AN7/PPGE(F) P66/AN6/PPGC(D) P65/AN5/PPGA(B) P64/AN4/PPG8(9) P63/AN3/PPG6(7) P62/AN2/PPG4(5) P61/AN1/PPG2(3) P60/AN0/PPG0(1) AVss AVRL AVRH AVcc P57/AN15 P35/HAK/OUT5 P36/RDY/OUT6 P37/CLK/OUT7 P40/X0A* P41/X1A* Vcc Vss C P42/IN6/INT9R P43/IN7 P44/SDA0/FRCK0 P45/SCL0/FRCK1 P46/SDA1 P47/SCL1 P50/AN8/SIN2 P51/AN9/SOT2 P52/AN10/SCK2 P53/AN11/TIN3 P54/AN12/TOT3 P55/AN13 P56/AN14 P33/WRH P34/HRQ/OUT4 P31/RD/IN5 P32/WRL/WR/INT10R 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 81 82 49 83 48 84 47 85 46 86 45 87 44 88 43 89 42 QFP - 100 90 41 91 40 92 39 93 38 94 37 95 36 96 35 97 34 98 33 99 32 100 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 P24/A20/IN0 P25/A21/IN1 P26/A22/IN2 P27/A23/IN3 P30/ALE/IN4 P04/AD04/INT12 P05/AD05/INT13 P06/AD06/INT14 P07/AD07/INT15 P10/AD08/TIN1 P11/AD09/TOT1 P12/AD10/SIN3/INT11R P13/AD11/SOT3 P14/AD12/SCK3 Vcc Vss X1 X0 P15/AD13 P16/AD14 P17/AD15 P20/A16/PPG9(8) P21/A17/PPGB(A) P22/A18/PPGD(C) P23/A19/PPGF(E) MD0 MD1 P03/AD03/INT11 P02/AD02/INT10 P01/AD01/INT9 P00/AD00/INT8 PA1 PA0/INT8R P97/OUT3 P96/OUT2 P95/OUT1 P94/OUT0 P93/PPG7(6) P92/PPG5(4) P91/PPG3(2) P90/PPG1(0) Vss Vcc P87/SCK1 P86/SOT1 P85/SIN1 P84/SCK0/INT15R P83/SOT0/TOT2 P82/SIN0/TIN2/INT14R P81/TOT0/CKOT/INT13R P80/TIN0/ADTG/INT12R P77/AN23/INT7 P76/AN22/INT6 (TOP VIEW) (FPT-100P-M06) * : X0A, X1A : MB90867E, MB90F867E P40, P41 : MB90867ES/MB90F867ES (Continued) 8 MB90860E Series (Continued) RST MD0 MD1 MD2 P75/AN21/INT5 P74/AN20/INT4 P73/AN19/INT3 P72/AN18/INT2 P71/AN17/INT1 P70/AN16/INT0 Vss P67/AN7/PPGE(F) P66/AN6/PPGC(D) P65/AN5/PPGA(B) P64/AN4/PPG8(9) P63/AN3/PPG6(7) P62/AN2/PPG4(5) P61/AN1/PPG2(3) P60/AN0/PPG0(1) AVss AVRL AVRH AVcc P57/AN15 P56/AN14 P55/AN13 P54/AN12/TOT3 P35/HAK/OUT5 P36/RDY/OUT6 P37/CLK/OUT7 P40/X0A* P41/X1A* Vcc Vss C P42/IN6/INT9R P43/IN7 P44/SDA0/FRCK0 P45/SCL0/FRCK1 P46/SDA1 P47/SCL1 P50/AN8/SIN2 P51/AN9/SOT2 P52/AN10/SCK2 P53/AN11/TIN3 P33/WRH P34/HRQ/OUT4 P26/A22/IN2 P27/A23/IN3 P30/ALE/IN4 P12/AD10/SIN3/INT11R P13/AD11/SOT3 P14/AD12/SCK3 Vcc Vss X1 X0 P15/AD13 P16/AD14 P17/AD15 P20/A16/PPG9(8) P21/A17/PPGB(A) P22/A18/PPGD(C) P23/A19/PPGF(E) P24/A20/IN0 P25/A21/IN1 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 76 50 77 49 48 78 47 79 46 80 45 81 44 82 43 83 42 84 41 85 40 86 39 87 LQFP - 100 38 88 37 89 36 90 35 91 34 92 33 93 32 94 31 95 30 96 29 97 98 28 99 27 100 26 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 P31/RD/IN5 P32/WRL/WR/INT10R P01/AD01/INT9 P02/AD02/INT10 P03/AD03/INT11 P04/AD04/INT12 P05/AD05/INT13 P06/AD06/INT14 P07/AD07/INT15 P10/AD08/TIN1 P11/AD09/TOT1 P81/TOT0/CKOT/INT13R P80/TIN0/ADTG/INT12R P77/AN23/INT7 P76/AN22/INT6 P00/AD00/INT8 PA1 PA0/INT8R P97/OUT3 P96/OUT2 P95/OUT1 P94/OUT0 P93/PPG7(6) P92/PPG5(4) P91/PPG3(2) P90/PPG1(0) Vss Vcc P87/SCK1 P86/SOT1 P85/SIN1 P84/SCK0/INT15R P83/SOT0/TOT2 P82/SIN0/TIN2/INT14R (TOP VIEW) (FPT-100P-M05) * : X0A, X1A : P40, P41 : MB90867E, MB90F867E MB90867ES, MB90F867ES 9 MB90860E Series PIN DESCRIPTION Pin No. QFP100*1 LQFP100*2 Pin name I/O Circuit type*3 General purpose I/O pins. The register can be set to select whether to use a pull-up resistor.In external bus mode, the pin is enabled as a general-purpose I/O port when the corresponding bit in the external address output control register (HACR) is 1. P24 to P27 1 to 4 99 to 2 G A20 to A23 Output pins of the external address bus. When the corresponding bit in the external address output control register (HACR) is 0, the pins are enabled as high address output pins (A20 to A23). IN0 to IN3 Trigger input pins for input captures 0 to 3. General purpose I/O pin.The register can be set to select whether to use a pull-up resistor.This function is enabled in single-chip mode. P30 5 6 7 3 G ALE Address latch enable output pin. This function is enabled when the external bus is enabled. IN4 Trigger input pin for input capture 4. P31 General purpose I/O pin.The register can be set to select whether to use a pull-up resistor.This function is enabled in single-chip mode. 4 G RD External read strobe output pin. This function is enabled when the external bus is enabled. IN5 Trigger input pin for input capture 5. P32 General purpose I/O pin. The register can be set to select whether to use a pull-up resistor. This function is enabled either in singlechip mode or with the WR/WRL pin output disabled. 5 G WR / WRL INT10R 6 General purpose I/O pin. The register can be set to select whether to use a pull-up resistor.This function is enabled either in singlechip mode or with the WRH pin output disabled. G WRH Write strobe output pin for the external data bus. This function is enabled when both the external bus and the WR/WRL pin output are enabled. WRL is used to write-strobe 8 lower bits of the data bus in 16-bit access while WR is used to write-strobe 8 bits of the data bus in 8-bit access. External interrupt request input pin (sub) . P33 8 Function Write strobe output pin for the 8 higher bits of the external data bus. This function is enabled when the external bus is enabled, when the external bus 16-bit mode is selected, and when the WRH output pin is enabled. (Continued) 10 MB90860E Series Pin No. QFP100*1 LQFP100*2 Pin name I/O Circuit type*3 General purpose I/O pin. The register can be set to select whether to use a pull-up resistor. This function is enabled either in single-chip mode or with the hold function disabled. P34 9 7 G HRQ Hold request input pin. This function is enabled when both the external bus and the hold function are enabled. OUT4 Waveform output pin for output compare 4. General purpose I/O pin. The register can be set to select whether to use a pull-up resistor. This function is enabled either in single-chip mode or with the hold function disabled. P35 10 8 G HAK OUT5 9 General purpose I/O pin. The register can be set to select whether to use a pull-up resistor. This function is enabled either in single-chip mode or with the external ready function disabled. G RDY External ready input pin. This function is enabled when both the external bus and the external ready function are enabled. OUT6 Waveform output pin for output compare 6. General purpose I/O pin. The register can be set to select whether to use a pull-up resistor. This function is enabled either in single-chip mode or with the clock output disabled. P37 12 10 G CLK OUT7 13, 14 Hold acknowledge output pin. This function is enabled when both the external bus and the hold function are enabled. Waveform output pin for output compare 5. P36 11 Function Clock output pin. This function is enabled when both the external bus and clock output are enabled. Waveform output pin for output compare 7. P40, P41 F General purpose I/O pins. (devices with S-suffix) X0A , X1A B Input pins for sub-clock (devices without S-suffix) 11, 12 15 13 VCC Power (3.5 V to 5.5 V) input pin 16 14 VSS GND pin 17 15 C K This is the power supply stabilization capacitor pin. It should be connected to a higher than or equal to 0.1 F ceramic capacitor. P42 18 16 IN6 INT9R General purpose I/O pin. F Trigger input pin for input capture 6. External interrupt request input pin (sub) (Continued) 11 MB90860E Series Pin No. QFP100*1 LQFP100*2 19 17 Pin name P43 IN7 I/O Circuit type*3 F P44 20 18 SDA0 H SCL0 20 23 21 P46 SDA1 P47 SCL1 H 25 22 23 AN8 H H O 27 28 25 26 27 30, 31 28, 29 32 30 General purpose I/O pin. Serial clock I/O pin for I2C 1 Analog input pin for the A/D converter Serial data input pin for UART2 P51 General purpose I/O pin. AN9 I AN10 Analog input pin for the A/D converter Serial data output pin for UART2 General purpose I/O pin. I Analog input pin for the A/D converter SCK2 Clock I/O pin for UART2 P53 General purpose I/O pin. AN11 I Analog input pin for the A/D converter TIN3 Event input pin for the reload timer 3 P54 General purpose I/O pin. AN12 I TOT3 29 Serial data I/O pin for I2C 1 SIN2 P52 24 General purpose I/O pin. General purpose I/O pin. SOT2 26 Serial clock I/O pin for I2C 0 Input pin for the 16-bit I/O Timer P50 24 Serial data I/O pin for I2C 0 General purpose I/O pin. FRCK1 22 Trigger input pin for input capture 7. Input pin for the 16-bit I/O Timer 0 P45 19 General purpose I/O pin. General purpose I/O pin. FRCK0 21 Function P55 AN13 P56, P57 AN14, AN15 AVCC Analog input pin for the A/D converter Output pin for the reload timer 3 I J K General purpose I/O pin. Analog input pin for the A/D converter General purpose I/O pins. Analog input pin for the A/D converter Power input pin for the A/D Converter analog (Continued) 12 MB90860E Series Pin No. QFP100*1 LQFP100*2 Pin name I/O Circuit type*3 Function 33 31 AVRH L Reference voltage input pin for the A/D Converter. This power supply must be turned on or off while a voltage higher than or equal to AVRH is applied to AVCC. 34 32 AVRL K Lower reference voltage input pin for the A/D Converter 35 33 AVSS K GND pin for the A/D Converter analog P60 to P67 36 to 43 34 to 41 AN0 to AN7 General purpose I/O pins. I PPG0, 2, 4, 6, 8, A, C, E 44 42 VSS Output pins for PPGs P70 to P75 45 to 50 43 to 48 AN16 to AN21 Analog input pins for the A/D converter GND pin General purpose I/O pins. I INT0 to INT5 Analog input pins for the A/D converter External interrupt request input pins 51 49 MD2 D Input pin for specifying the operating mode. 52, 53 50, 51 MD1, MD0 C Input pins for specifying the operating mode. 54 52 RST E Reset input P76, P77 55, 56 53, 54 AN22, AN23 General purpose I/O pins. I INT6, INT7 External interrupt request input pins P80 57 55 TIN0 ADTG General purpose I/O pin. F INT12R 56 TOT0 CKOT F SIN0 TIN2 M SOT0 F SCK0 INT15R Serial data output pin for UART0 Output pin for the reload timer 2 P84 59 Event input pin for the reload timer 2 General purpose I/O pin. TOT2 61 Serial data input pin for UART0 External interrupt request input pin (sub) P83 58 Output pin for the clock monitor General purpose I/O pin. INT14R 60 Output pin for the reload timer 0 External interrupt request input pin (sub) P82 57 Trigger input pin for the A/D converter General purpose I/O pin. INT13R 59 Event input pin for the reload timer 0 External interrupt request input pin (sub) P81 58 Analog input pins for the A/D converter General purpose I/O pin. F Clock I/O pin for UART0 External interrupt request input pin (sub) (Continued) 13 MB90860E Series Pin No. QFP100*1 LQFP100*2 Pin name P85 I/O Circuit type*3 General purpose I/O pin. 62 60 63 61 64 62 65 63 VCC Power (3.5 V to 5.5 V) input pins 66 64 VSS GND pins 67 to 70 65 to 68 71 to 74 69 to 72 75 73 76 74 SIN1 P86 SOT1 P87 SCK1 P90 to P93 PPG1, 3, 5, 7 M Function F F F P94 to P97 OUT0 to OUT3 PA0 INT8R PA1 75 to 82 F F 86 Serial data output pin for UART1 General purpose I/O pin. Clock I/O pin for UART1 General purpose I/O pin Output pins for PPGs Waveform output pins for output compares 0 to 3. This function is enabled when the OCU enables waveform output. General purpose I/O pin. External interrupt request input pin (sub) General purpose I/O pin. General purpose I/O pins. The register can be set to select whether to use a pull-up resistor. This function is enabled in single-chip mode. G AD00 to AD07 I/O pins for 8 lower bits of the external address/data bus. This function is enabled when the external bus is enabled. INT8 to INT15 External interrupt request input pins. General purpose I/O pin. The register can be set to select whether to use a pull-up resistor. This function is enabled in single-chip mode. P10 85 General purpose I/O pin. General purpose I/O pin F P00 to P07 77 to 84 Serial data input pin for UART1 83 G AD08 I/O pin for the external address/data bus. This function is enabled when the external bus is enabled. TIN1 Event input pin for the reload timer 1 P11 General purpose I/O pin. The register can be set to select whether to use a pull-up resistor. This function is enabled in single-chip mode. 84 G AD09 I/O pin for the external address/data bus. This function is enabled when the external bus is enabled. TOT1 Output pin for the reload timer 1 (Continued) 14 MB90860E Series Pin No. QFP100*1 LQFP100*2 Pin name I/O Circuit type*3 General purpose I/O pin. The register can be set to select whether to use a pull-up resistor. This function is enabled in single-chip mode. P12 87 85 AD10 N SIN3 External interrupt request input pin (sub) General purpose I/O pin. The register can be set to select whether to use a pull-up resistor. This function is enabled in single-chip mode. P13 86 G AD11 I/O pin for the external address/data bus. This function is enabled when the external bus is enabled. SOT3 Serial data output pin for UART3 General purpose I/O pin. The register can be set to select whether to use a pull-up resistor. This function is enabled in single-chip mode. P14 89 I/O pin for the external address/data bus. This function is enabled when the external bus is enabled. Serial data input pin for UART3 INT11R 88 Function 87 G AD12 I/O pin for the external address/data bus. This function is enabled when the external bus is enabled. SCK3 Clock I/O pin for UART3 90 88 VCC Power (3.5 V to 5.5 V) input pin 91 89 VSS GND pin 92 90 X1 93 91 X0 A P15 94 92 G P16 93 G P17 94 G AD15 General purpose I/O pin. The register can be set to select whether to use a pull-up resistor. This function is enabled in single-chip mode. General purpose I/O pin. The register can be set to select whether to use a pull-up resistor. This function is enabled in single-chip mode. I/O pin for the external address/data bus. This function is enabled when the external bus is enabled. AD14 96 Main clock input pin I/O pin for the external address/data bus. This function is enabled when the external bus is enabled. AD13 95 Main clock output pin General purpose I/O pin. The register can be set to select whether to use a pull-up resistor. This function is enabled in single-chip mode. I/O pin for the external address/data bus. This function is enabled when the external bus is enabled. (Continued) 15 MB90860E Series (Continued) Pin No. QFP100*1 LQFP100*2 Pin name I/O Circuit type*3 General purpose I/O pins. The register can be set to select whether to use a pull-up resistor.In external bus mode, the pin is enabled as a general-purpose I/O port when the corresponding bit in the external address output control register (HACR) is 1. P20 to P23 97 to 100 95 to 98 G A16 to A19 PPG9,PPGB, PPGD,PPGF Function Output pins of the external address bus. When the corresponding bit in the external address output control register (HACR) is 0, the pins are enabled as high address output pins (A16 to A19). Output pins for PPGs *1 : FPT-100P-M06 *2 : FPT-100P-M05 *3 : For the I/O circuit type, refer to " I/O CIRCUIT TYPE". 16 MB90860E Series I/O CIRCUIT TYPE Type Circuit X1 A Remarks Xout * Oscillation circuit High-speed oscillation feedback resistor = approx. 1 M X0 Standby control signal X1A B Xout * Oscillation circuit Low-speed oscillation feedback resistor = approx. 10 M X0A Standby control signal Hysteresis inputs * Mask ROM and evaluation device: CMOS Hysteresis input pin * Flash device: CMOS input pin Hysteresis inputs * Mask ROM and evaluation device: CMOS Hysteresis input pin Pull-down resistor value: approx. 50 k * Flash memory device: CMOS input pin No Pull-down R C R D Pull-down Resistor CMOS Hysteresis input pin Pull-up resistor value: approx. 50 k E Pull-up Resistor R Hysteresis inputs (Continued) 17 MB90860E Series Type Circuit F Remarks P-ch Pout N-ch Nout * CMOS level output (IOL = 4 mA, IOH = -4 mA) * CMOS hysteresis inputs (With the standbytime input shutdown function) * Automotive input (With the standby-time input shutdown function) R Hysteresis inputs Automotive inputs Standby control for input shutdown Pull-up control P-ch P-ch Pout N-ch G Nout R Hysteresis inputs * CMOS level output (IOL = 4 mA, IOH = -4 mA) * CMOS hysteresis inputs (With the standbytime input shutdown function) * Automotive input (With the standby-time input shutdown function) * TTL input (With the standby-time input shutdown function) * Programmable pull-up resistor: 50 k approx. Automotive inputs TTL input Standby control for input shutdown H P-ch Pout N-ch Nout * CMOS level output (IOL = 3 mA, IOH = -3 mA) * CMOS hysteresis inputs (With the standbytime input shutdown function) * Automotive input (With the standby-time input shutdown function) R Hysteresis inputs Automotive inputs Standby control for input shutdown (Continued) 18 MB90860E Series Type Circuit Remarks P-ch Pout N-ch Nout * CMOS level output (IOL = 4 mA, IOH = -4 mA) * CMOS hysteresis inputs (With the standbytime input shutdown function) * Automotive input (With the standby-time input shutdown function) * A/D converter analog input R I Hysteresis inputs Automotive inputs Standby control for input shutdown Analog input P-ch Pout N-ch Nout * CMOS level output (IOL = 4 mA, IOH = -4 mA) * D/A analog output * CMOS hysteresis inputs (With the standbytime input shutdown function) * Automotive input (With the standby-time input shutdown function) * A/D converter analog input R Hysteresis inputs J Automotive inputs Standby control for input shutdown Analog input Analog output Power supply input protection circuit P-ch K N-ch P-ch L ANE * A/D converter reference voltage power supply input pin, with the protection circuit * Flash devices do not have a protection circuit against VCC for pin AVRH AVR N-ch ANE (Continued) 19 MB90860E Series (Continued) Type Circuit M P-ch Pout N-ch Nout Remarks * CMOS level output (IOL = 4 mA, IOH = -4 mA) * CMOS inputs (With the standby-time input shutdown function) * Automotive input (With the standby-time input shutdown function) R CMOS inputs Automotive inputs Standby control for input shutdown Pull-up control P-ch P-ch Pout N-ch N Nout R CMOS inputs * CMOS level output (IOL = 4 mA, IOH = -4 mA) * CMOS inputs (With the standby-time input shutdown function) * Automotive input (With the standby-time input shutdown function) * TTL input (With the standby-time input shutdown function) Programmable pull-up registor:50 k approx Automotive inputs TTL input Standby control for input shutdown P-ch Pout N-ch Nout R O CMOS inputs Automotive inputs Standby control for input shutdown Analog input 20 * CMOS level output(IOL = 4 mA, IOH = -4 mA) * CMOS inputs (With the standby-time input shutdown function) * Automotive input (With the standby-time input shutdown function) * A/D converter analog input MB90860E Series HANDLING DEVICES 1. Preventing latch-up CMOS IC may suffer latch-up under the following conditions : * A voltage higher than VCC or lower than VSS is applied to an input or output pin. * A voltage higher than the rated voltage is applied between VCC and VSS pins. * The AVCC power supply is applied before the VCC voltage. Latch-up may increase the power supply current drastically, causing thermal damage to the device. For the same reason, also be careful not to let the analog power-supply voltage (AVCC, AVRH) exceed the digital power-supply voltage. 2. Handling unused pins Leaving unused input pins open may result in misbehavior or latch up and possible permanent damage of the device. Therefore they must be pulled up or pulled down through resistors. In this case those resistors should be more than 2 k . Unused bidirectional pins should be set to the output state and can be left open, or the input state with the above described connection. 3. Power supply pins (VCC/VSS) * If there are multiple VCC and VSS pins, from the point of view of device design, pins to be of the same potential are connected the inside of the device to prevent such malfunctioning as latch up. To reduce unnecessary radiation, prevent malfunctioning of the strobe signal due to the rise of ground level, and observe the standard for total output current, be sure to connect the VCC and VSS pins to the power supply and ground externally. * Connect VCC and VSS to the device from the current supply source at a low impedance. * As a measure against power supply noise, connect a capacitor of about 0.1 F as a bypass capacitor between VCC and VSS in the vicinity of VCC and VSS pins of the device Vcc Vss Vcc Vss Vss Vcc MB90860E Series Vcc Vss Vss Vcc 4. Mode Pin (MD0 to MD2) Connect the mode pin directly to VCC or VSS pins. To prevent the device unintentionally entering test mode due to noise, lay out the printed circuit board so as to minimize the distance from the mode pins to VCC or VSS pins and to provide a low-impedance connection. 21 MB90860E Series 5. Turning-on Sequence of Power Supply to A/D Converter and Analog Inputs Make sure to turn on the A/D converter power supply (AVCC, AVRH, AVRL) and analog inputs (AN0 to AN23) after turning-on the digital power supply (VCC) . Turn-off the digital power after turning off the A/D converter supply and analog inputs. In this case, make sure that the voltage not exceed AVRH or AVCC (turning on/off the analog and digital power supplies simultaneously is acceptable) . 6. Connection of Unused Pins of A/D Converter if A/D Converter is used Connect unused pins of A/D converter to AVCC = VCC, AVSS = AVRH = AVRL = VSS. 7. Crystal Oscillator Circuit X0, X1 pins and X0A, X1A pins may be possible causes of abnormal operations. Make sure to provide bypass capacitors via shortest distance from X0, X1 pins and X0A, X1A pins, crystal oscillator (or ceramic oscillator) and ground lines, and make sure, to the utmost effort, that lines of oscillation circuit not cross the lines of other circuits. It is highly recommended to provide a printed circuit board art work surrounding X0, X1 pins and X0A, X1A pins with a ground area for stabilizing the operation. 8. Pull-up/down resistors The MB90860E Series does not support internal pull-up/down resistors (Port 0 to Port 3: built-in pull-up resistors). Use external components where needed. 9. Using external clock To use external clock, drive the X0 pin and leave X1 pin open. MB90860E Series X0 Open X1 10. Precautions for when not using a sub clock signal If you do not connect pins X0A and X1A to an oscillator, use pull-down handling on the X0A pin, and leave the X1A pin open. 11. Notes on during operation of PLL clock mode If the PLL clock mode is selected, the MB90860 series attempt to be working with the self-oscillating circuit even when there is no external oscillator or external clock input is stopped. Performance of this operation, however, cannot be guaranteed. 12. Notes on Energization To prevent the internal regulator circuit from malfunctioning, set the voltage rise time during energization at 50 or more s (0.2 V to 2.7 V) 22 MB90860E Series 13. Stabilization of power supply voltage A sudden change in the supply voltage may cause the device to malfunction even within the specified VCC supply voltage operating range. Therefore, the VCC supply voltage should be stabilized. For the reference, stabilize the supply voltage by setting the following value. * VCC ripple variations (peak-to-peak value) at commercial frequencies (50 Hz/60 Hz) fall below 10% of the standard VCC supply voltage * The coefficient of fluctuation does not exceed 0.1 V/ms at instantaneous power switching. 14. Initialization In the device, there are internal registers which are initialized only by a power-on reset. To initialize these registers, turn on the power again. 15. Port 0 to port 3 output during Power-on (External-bus mode) As shown below, when power is turned on in External-Bus mode, in spite of reset input, there is a possibility that output signal of Port 0 to Port 3 might be unstable. 1/2VCC VCC Port 0 to Port 3 Port 0 to Port 3 outputs might be unstable Port 0 to Port 3 outputs = Hi-Z 16. Flash security Function The security bit is located in the area of the flash memory. If protection code 01H is written in the security bit, the flash memory is in the protected state by security. Therefore please do not write 01H in this address if you do not use the security function. Please refer to following table for the address of the security bit. MB90F867E(S) Flash memory size Address for security bit Embedded 1 Mbit Flash Memory FE0001H 23 MB90860E Series BLOCK DIAGRAMS * MB90V340E-101/102 X0,X1 X0A,X1A* RST Clock Controller 16LX CPU RAM 30 Kbytes AVCC AVSS AN23 to AN0 AVRH AVRL ADTG DA01, DA00 FRCK0 Input Capture 8 channels IN7 to IN0 Output Compare 8 channels OUT7 to OUT0 Prescaler 5 channels I/O Timer 1 UART 5 channels CAN Controller 3 channels RX2 to RX0 TX2 to TX0 16-bit Reload Timer 4 channels TIN3 to TIN0 TOT3 to TOT0 8/10-bit ADC 24 channels 10-bit DAC 2 channels FRCK1 AD15 to AD00 F2MC-16 Bus SOT4 to SOT0 SCK4 to SCK0 SIN4 to SIN0 I/O Timer 0 A23 to A16 ALE RD External Bus Interface WR/WRL WRH HRQ PPGF to PPG0 SDA1, SDA0 SCL1, SCL0 I2C Interface 2 channels DMAC * : Only for MB90V340E-102 24 HAK 8/16-bit PPG 16 channels RDY CLK External Interrupt 16 channels Clock Monitor INT15 to INT8 (INT15R to INT8R) INT7 to INT0 CKOT MB90860E Series * MB90867E(S), MB90F867E(S) X0,X1 X0A,X1A* RST Clock Controller 16LX CPU RAM 6 Kbytes ROM/Flash 128 Kbytes Prescaler 4 channels AVCC AVSS AN15 to AN0 AN23 to AN16 AVRH AVRL ADTG PPGF to PPG0 FRCK0 Input Capture 8 channels IN7 to IN0 Output Compare 8 channels OUT7 to OUT0 I/O Timer 1 FRCK1 UART 4 channels 16-bit Reload Timer 4 channels 8/10-bit ADC 24 channels TIN3 to TIN0 TOT3 to TOT0 AD15 to AD00 F2MC-16 Bus SOT3 to SOT0 SCK3 to SCK0 SIN3 to SIN0 I/O Timer 0 A23 to A16 ALE RD External Bus Interface 8/16-bit PPG 16 channels WR/WRL WRH HRQ HAK RDY SDA1, SDA0 SCL1, SCL0 I2C Interface 2 channels CLK External Interrupt 16 channels INT15 to INT8 (INT15R to INT8R) INT7 to INT0 DMAC Clock Monitor CKOT * : Only for devices without `S' Suffix 25 MB90860E Series MEMORY MAP MB90867E(S) MB90F867E(S) MB90V340E-101/102 000000H 0000EFH 000100H Peripheral External access area 000000H 0000EFH 000100H Peripheral External access area RAM 6 Kbytes 003FFFH RAM 30 Kbytes 0078FFH 007900H 007900H Peripheral 007FFFH 008000H 00FFFFH ROM (image of FF bank) Peripheral 007FFFH 008000H 00FFFFH ROM (image of FF bank) External access area F80000H F8FFFFH F90000H ROM (F8 bank) ROM (F9 bank) F9FFFFH FA0000H ROM (FA bank) FAFFFFH FB0000H External access area ROM (FB bank) FBFFFFH FC0000H FCFFFFH FD0000H ROM (FC bank) ROM (FD bank) FDFFFFH FE0000H FE0000H ROM (FE bank) FEFFFFH FF0000H FEFFFFH FF0000H ROM (FF bank) FFFFFFH ROM (FE bank) ROM (FF bank) FFFFFFH : No access Note : The high-order portion of bank 00 gives the image of the FF bank ROM to make the small model of the C compiler effective. Since the low-order 16 bits are the same, the table in ROM can be referenced without using the far specification in the pointer declaration. For example, an attempt to access 00C000H accesses the value at FFC000H in ROM. The ROM area in bank FF exceeds 32 Kbytes, and its entire image cannot be shown in bank 00. The image between FF8000H and FFFFFFH is visible in bank 00, while the image between FF0000H and FF7FFFH is visible only in bank FF. 26 MB90860E Series I/O MAP Abbreviation Access Resource name Initial value 000000H Port 0 Data Register PDR0 R/W Port 0 XXXXXXXXB 000001H Port 1 Data Register PDR1 R/W Port 1 XXXXXXXXB 000002H Port 2 Data Register PDR2 R/W Port 2 XXXXXXXXB 000003H Port 3 Data Register PDR3 R/W Port 3 XXXXXXXXB 000004H Port 4 Data Register PDR4 R/W Port 4 XXXXXXXXB 000005H Port 5 Data Register PDR5 R/W Port 5 XXXXXXXXB 000006H Port 6 Data Register PDR6 R/W Port 6 XXXXXXXXB 000007H Port 7 Data Register PDR7 R/W Port 7 XXXXXXXXB 000008H Port 8 Data Register PDR8 R/W Port 8 XXXXXXXXB 000009H Port 9 Data Register PDR9 R/W Port 9 XXXXXXXXB 00000AH Port A Data Register PDRA R/W Port A XXXXXXXXB 00000BH Port 5 Analog Input Enable Register ADER5 R/W Port 5, A/D 11111111B 00000CH Port 6 Analog Input Enable Register ADER6 R/W Port 6, A/D 11111111B 00000DH Port 7 Analog Input Enable Register ADER7 R/W Port 7, A/D 11111111B 00000EH Input Level Select Register 0 ILSR0 R/W Ports XXXXXXXXB 00000FH Input Level Select Register 1 ILSR1 R/W Ports XXXX0XXXB 000010H Port 0 Direction Register DDR0 R/W Port 0 00000000B 000011H Port 1 Direction Register DDR1 R/W Port 1 00000000B 000012H Port 2 Direction Register DDR2 R/W Port 2 00000000B 000013H Port 3 Direction Register DDR3 R/W Port 3 00000000B 000014H Port 4 Direction Register DDR4 R/W Port 4 00000000B 000015H Port 5 Direction Register DDR5 R/W Port 5 00000000B 000016H Port 6 Direction Register DDR6 R/W Port 6 00000000B 000017H Port 7 Direction Register DDR7 R/W Port 7 00000000B 000018H Port 8 Direction Register DDR8 R/W Port 8 00000000B 000019H Port 9 Direction Register DDR9 R/W Port 9 00000000B 00001AH Port A Direction Register DDRA R/W Port A 00000100B Address Register 00001BH Reserved 00001CH Port 0 Pull-up Control Register PUCR0 R/W Port 0 00000000B 00001DH Port 1 Pull-up Control Register PUCR1 R/W Port 1 00000000B 00001EH Port 2 Pull-up Control Register PUCR2 R/W Port 2 00000000B 00001FH Port 3 Pull-up Control Register PUCR3 W, R/W Port 3 00000000B (Continued) 27 MB90860E Series Abbreviation Access Resource name Initial value 000020H Serial Mode Register 0 SMR0 W,R/W 00000000B 000021H Serial Control Register 0 SCR0 W,R/W 00000000B 000022H Reception/Transmission Data Register 0 RDR0/ TDR0 R/W 00000000B 000023H Serial Status Register 0 SSR0 R,R/W ECCR0 R,W, R/W 000025H Extended Status/Control Register 0 ESCR0 R/W 00000100B 000026H Baud Rate Generator Register 00 BGR00 R/W 00000000B 000027H Baud Rate Generator Register 01 BGR01 R/W 00000000B 000028H Serial Mode Register 1 SMR1 W,R/W 00000000B 000029H Serial Control Register 1 SCR1 W,R/W 00000000B 00002AH Reception/Transmission Data Register 1 RDR1/ TDR1 R/W 00000000B 00002BH Serial Status Register 1 SSR1 R,R/W ECCR1 R,W, R/W 00002DH Extended Status/Control Register 1 ESCR1 R/W 00000100B 00002EH Baud Rate Generator Register 10 BGR10 R/W 00000000B 00002FH Baud Rate Generator Register 11 BGR11 R/W 00000000B 000030H PPG 0 Operation Mode Control Register PPGC0 W,R/W 0X000XX1B 000031H PPG 1 Operation Mode Control Register PPGC1 W,R/W 000032H PPG 0/PPG 1 Count Clock Select Register PPG01 R/W 000000X0B 0X000XX1B Address 000024H 00002CH Register Extended Communication Control Register 0 Extended Communication Control Register 1 000033H UART0 00001000B 000000XXB UART1 00001000B 000000XXB 16-bit PPG 0/1 0X000001B Reserved 000034H PPG 2 Operation Mode Control Register PPGC2 W,R/W 000035H PPG 3 Operation Mode Control Register PPGC3 W,R/W 000036H PPG 2/PPG 3 Count Clock Select Register PPG23 R/W 000000X0B 0X000XX1B 000037H PPGC4 W,R/W 000039H PPG 5 Operation Mode Control Register PPGC5 W,R/W 00003AH PPG 4/PPG 5 Clock Select Register PPG45 R/W PACSR1 R/W 00003CH PPG 6 Operation Mode Control Register PPGC6 W,R/W 00003DH PPG 7 Operation Mode Control Register PPGC7 W,R/W 00003EH PPG 6/PPG 7 Count Clock Control Register PPG67 R/W 00003FH 0X000001B Reserved 000038H PPG 4 Operation Mode Control Register 00003BH Address Detect Control Register 1 16-bit PPG 2/3 16-bit PPG 4/5 0X000001B 000000X0B Address Match Detection 1 00000000B 0X000XX1B 16-bit PPG 6/7 0X000001B 000000X0B Reserved (Continued) 28 MB90860E Series Abbreviation Access 000040H PPG 8 Operation Mode Control Register PPGC8 W,R/W 000041H PPG 9 Operation Mode Control Register PPGC9 W,R/W PPG89 R/W 000000X0B 0X000XX1B Address 000042H Register PPG 8/PPG 9 Count Clock Control Register 000043H Resource name Initial value 0X000XX1B 16-bit PPG 8/9 0X000001B Reserved 000044H PPG A Operation Mode Control Register PPGCA W,R/W 000045H PPG B Operation Mode Control Register PPGCB W,R/W PPGAB R/W 000000X0B 0X000XX1B 000046H PPG A/PPG B Count Clock Select Register 000047H 16-bit PPG A/B 0X000001B Reserved 000048H PPG C Operation Mode Control Register PPGCC W,R/W 000049H PPG D Operation Mode Control Register PPGCD W,R/W PPGCD R/W 000000X0B 0X000XX1B 00004AH PPG C/PPG D Count Clock Select Register 00004BH 0X000001B Reserved 00004CH PPG E Operation Mode Control Register PPGCE W,R/W 00004DH PPG F Operation Mode Control Register PPGCF W,R/W PPGEF R/W 00004EH 16-bit PPG C/D PPG E/PPG F Count Clock Select Register 00004FH 16-bit PPG E/F 0X000001B 000000X0B Reserved 000050H Input Capture Control Status 0/1 ICS01 R/W 000051H Input Capture Edge 0/1 ICE01 R/W, R 000052H Input Capture Control Status 2/3 ICS23 R/W 000053H Input Capture Edge 2/3 ICE23 R 000054H Input Capture Control Status 4/5 ICS45 R/W 000055H Input Capture Edge 4/5 ICE45 R 000056H Input Capture Control Status 6/7 ICS67 R/W 000057H Input Capture Edge 6/7 ICE67 R/W, R 000058H Output Compare Control Status 0 OCS0 R/W 000059H Output Compare Control Status 1 OCS1 R/W 00005AH Output Compare Control Status 2 OCS2 R/W 00005BH Output Compare Control Status 3 OCS3 R/W 00005CH Output Compare Control Status 4 OCS4 R/W 00005DH Output Compare Control Status 5 OCS5 R/W 00005EH Output Compare Control Status 6 OCS6 R/W 00005FH Output Compare Control Status 7 OCS7 R/W Input Capture 0/1 Input Capture 2/3 Input Capture 4/5 Input Capture 6/7 Output Compare 0/1 Output Compare 2/3 Output Compare 4/5 Output Compare 6/7 00000000B XXX0X0XXB 00000000B XXXXXXXXB 00000000B XXXXXXXXB 00000000B XXX000XXB 0000XX00B 0XX00000B 0000XX00B 0XX00000B 0000XX00B 0XX00000B 0000XX00B 0XX00000B (Continued) 29 MB90860E Series Abbreviation Access Resource name Initial value 000060H Timer Control Status 0 TMCSR0 R/W 00000000B 000061H Timer Control Status 0 TMCSR0 R/W 16-bit Reload Timer 0 000062H Timer Control Status 1 TMCSR1 R/W 000063H Timer Control Status 1 TMCSR1 R/W 000064H Timer Control Status 2 TMCSR2 R/W 000065H Timer Control Status 2 TMCSR2 R/W 000066H Timer Control Status 3 TMCSR3 R/W 000067H Timer Control Status 3 TMCSR3 R/W 000068H A/D Control Status 0 ADCS0 R/W 000XXXX0B 000069H A/D Control Status 1 ADCS1 R/W 0000000XB 00006AH A/D Data 0 ADCR0 R 00006BH A/D Data 1 ADCR1 R 00006CH ADC Setting 0 ADSR0 R/W 00000000B 00006DH ADC Setting 1 ADSR1 R/W 00000000B 00006EH Reserved 00006FH ROM Mirror Function Select ROMM 000070H to 00009AH Reserved Address 00009BH Register DMA Descriptor Channel Specified Register W 16-bit Reload Timer 1 16-bit Reload Timer 2 16-bit Reload Timer 3 A/D Converter ROM Mirror XXXX0000B 00000000B XXXX0000B 00000000B XXXX0000B 00000000B XXXX0000B 00000000B XXXXXX00B XXXXXXX1B DCSR R/W 00009CH DMA Status L Register DSRL R/W 00009DH DMA Status H Register DSRH R/W PACSR0 R/W DIRR R/W 0000A0H Low-power Mode Control Register LPMCR W,R/W Low Power Control Circuit 00011000B 0000A1H Clock Selection Register CKSCR R,R/W Low Power Control Circuit 11111100B 0000A2H, 0000A3H Reserved DMA 00000000B 00009EH Address Detect Control Register 0 00009FH Delayed Interrupt/release 0000A4H DMA Stop Status Register DSSR R/W 0000A5H Automatic Ready Function Select Register ARSR W 0000A6H External Address Output Control Register HACR W 0000A7H Bus Control Signal Selection Register ECSR W 0000A8H Watchdog Control Register WDTC R,W 00000000B DMA 00000000B 00000000B Address Match Detection 0 00000000B Delayed Interrupt XXXXXXX0B 0011XX00B External Memory Access 00000000B 0000000XB Watchdog Timer XXXXX111B (Continued) 30 MB90860E Series Abbreviation Access Resource name Initial value 0000A9H Time Base Timer Control Register TBTC W,R/W Time Base Timer 1XX00100B 0000AAH Watch Timer Control Register WTC R,R/W Watch Timer 1X001000B Address Register 0000ABH Reserved 0000ACH DMA Enable L Register DERL R/W 0000ADH DMA Enable H Register DERH R/W FMCS R,R/W 0000AEH Flash Control Status Register (Flash Devices only. Otherwise reserved) 0000AFH DMA Flash Memory 00000000B 00000000B 000X0000B Reserved 0000B0H Interrupt Control Register 00 ICR00 W,R/W 00000111B 0000B1H Interrupt Control Register 01 ICR01 W,R/W 00000111B 0000B2H Interrupt Control Register 02 ICR02 W,R/W 00000111B 0000B3H Interrupt Control Register 03 ICR03 W,R/W 00000111B 0000B4H Interrupt Control Register 04 ICR04 W,R/W 00000111B 0000B5H Interrupt Control Register 05 ICR05 W,R/W 00000111B 0000B6H Interrupt Control Register 06 ICR06 W,R/W 00000111B 0000B7H Interrupt Control Register 07 ICR07 W,R/W 0000B8H Interrupt Control Register 08 ICR08 W,R/W 0000B9H Interrupt Control Register 09 ICR09 W,R/W 00000111B 0000BAH Interrupt Control Register 10 ICR10 W,R/W 00000111B 0000BBH Interrupt Control Register 11 ICR11 W,R/W 00000111B 0000BCH Interrupt Control Register 12 ICR12 W,R/W 00000111B 0000BDH Interrupt Control Register 13 ICR13 W,R/W 00000111B 0000BEH Interrupt Control Register 14 ICR14 W,R/W 00000111B 0000BFH Interrupt Control Register 15 ICR15 W,R/W 00000111B 0000C0H D/A Converter Data 0 Register DAT0 R/W XXXXXXXXB 0000C1H D/A Converter Data 1 Register DAT1 R/W 0000C2H D/A Control 0 Register DACR0 R/W 0000C3H D/A Control 1 Register DACR1 R/W XXXXXXX0B 00000000B 0000C4H, 0000C5H Interrupt Control D/A Converter 00000111B 00000111B XXXXXXXXB XXXXXXX0B Reserved 0000C6H External Interrupt Enable 0 ENIR0 R/W 0000C7H External Interrupt Source 0 EIRR0 R/W 0000C8H External Interrupt Level Setting 0 ELVR0 R/W 0000C9H External Interrupt Level Setting 0 ELVR0 R/W External Interrupt 0 XXXXXXXXB 00000000B 00000000B (Continued) 31 MB90860E Series Abbreviation Access 0000CAH External Interrupt Enable 1 ENIR1 R/W 00000000B 0000CBH External Interrupt Source 1 EIRR1 R/W XXXXXXXXB 0000CCH External Interrupt Level Setting 1 ELVR1 R/W 0000CDH External Interrupt Level Setting 1 ELVR1 R/W 00000000B 0000CEH External Interrupt Source Select EISSR R/W 00000000B 0000CFH PLL/Sub Clock Control Register PSCCR W 0000D0H DMA Buffer Address Pointer L Register BAPL R/W XXXXXXXXB 0000D1H DMA Buffer Address Pointer M Register BAPM R/W XXXXXXXXB 0000D2H DMA Buffer Address Pointer H Register BAPH R/W XXXXXXXXB DMACS R/W XXXXXXXXB Address Register 0000D3H DMA Control Register Resource name External Interrupt 1 PLL Initial value 00000000B XXXX0000B 0000D4H I/O Register Address Pointer L Register IOAL R/W 0000D5H I/O Register Address Pointer H Register IOAH R/W XXXXXXXXB 0000D6H Data Counter L Register DCTL R/W XXXXXXXXB 0000D7H Data Counter H Register DCTH R/W XXXXXXXXB 0000D8H Serial Mode Register 2 SMR2 W,R/W 00000000B 0000D9H Serial Control Register 2 SCR2 W,R/W 00000000B RDR2/ TDR2 R/W 00000000B SSR2 R,R/W ECCR2 R,W, R/W 0000DDH Extended Status Control Register 2 ESCR2 R/W 00000100B 0000DEH Baud Rate Generator Register 20 BGR20 R/W 00000000B 0000DFH Baud Rate Generator Register 21 BGR21 R/W 00000000B 0000E0H to 0000FFH External area 0000DAH Reception/Transmission Data Register 2 0000DBH Serial Status Register 2 0000DCH Extended Communication Control Register 2 DMA UART2 XXXXXXXXB 00001000B 000000XXB 007900H Reload Register L0 PRLL0 R/W 007901H Reload Register H0 PRLH0 R/W 007902H Reload Register L1 PRLL1 R/W 007903H Reload Register H1 PRLH1 R/W XXXXXXXXB 007904H Reload Register L2 PRLL2 R/W XXXXXXXXB 007905H Reload Register H2 PRLH2 R/W 007906H Reload Register L3 PRLL3 R/W 007907H Reload Register H3 PRLH3 R/W XXXXXXXXB 16-bit PPG 0/1 16-bit PPG 2/3 XXXXXXXXB XXXXXXXXB XXXXXXXXB XXXXXXXXB XXXXXXXXB (Continued) 32 MB90860E Series Abbreviation Access 007908H Reload Register L4 PRLL4 R/W 007909H Reload Register H4 PRLH4 R/W 00790AH Reload Register L5 PRLL5 R/W 00790BH Reload Register H5 PRLH5 R/W XXXXXXXXB 00790CH Reload Register L6 PRLL6 R/W XXXXXXXXB 00790DH Reload Register H6 PRLH6 R/W 00790EH Reload Register L7 PRLL7 R/W 00790FH Reload Register H7 PRLH7 R/W XXXXXXXXB 007910H Reload Register L8 PRLL8 R/W XXXXXXXXB 007911H Reload Register H8 PRLH8 R/W 007912H Reload Register L9 PRLL9 R/W 007913H Reload Register H9 PRLH9 R/W XXXXXXXXB 007914H Reload Register LA PRLLA R/W XXXXXXXXB 007915H Reload Register HA PRLHA R/W 007916H Reload Register LB PRLLB R/W 007917H Reload Register HB PRLHB R/W XXXXXXXXB 007918H Reload Register LC PRLLC R/W XXXXXXXXB 007919H Reload Register HC PRLHC R/W 00791AH Reload Register LD PRLLD R/W 00791BH Reload Register HD PRLHD R/W XXXXXXXXB 00791CH Reload Register LE PRLLE R/W XXXXXXXXB 00791DH Reload Register HE PRLHE R/W 00791EH Reload Register LF PRLLF R/W 00791FH Reload Register HF PRLHF R/W XXXXXXXXB 007920H Input Capture 0 IPCP0 R XXXXXXXXB 007921H Input Capture 0 IPCP0 R 007922H Input Capture 1 IPCP1 R 007923H Input Capture 1 IPCP1 R XXXXXXXXB 007924H Input Capture 2 IPCP2 R XXXXXXXXB 007925H Input Capture 2 IPCP2 R 007926H Input Capture 3 IPCP3 R 007927H Input Capture 3 IPCP3 R XXXXXXXXB 007928H Input Capture 4 IPCP4 R XXXXXXXXB 007929H Input Capture 4 IPCP4 R 00792AH Input Capture 5 IPCP5 R 00792BH Input Capture 5 IPCP5 R Address Register Resource name Initial value XXXXXXXXB 16-bit PPG 4/5 16-bit PPG 6/7 16-bit PPG 8/9 16-bit PPG A/B 16-bit PPG C/D 16-bit PPG E/F Input Capture 0/1 Input Capture 2/3 Input Capture 4/5 XXXXXXXXB XXXXXXXXB XXXXXXXXB XXXXXXXXB XXXXXXXXB XXXXXXXXB XXXXXXXXB XXXXXXXXB XXXXXXXXB XXXXXXXXB XXXXXXXXB XXXXXXXXB XXXXXXXXB XXXXXXXXB XXXXXXXXB XXXXXXXXB XXXXXXXXB XXXXXXXXB XXXXXXXXB (Continued) 33 MB90860E Series Abbreviation Access 00792CH Input Capture 6 IPCP6 R 00792DH Input Capture 6 IPCP6 R 00792EH Input Capture 7 IPCP7 R 00792FH Input Capture 7 IPCP7 R XXXXXXXXB 007930H Output Compare 0 OCCP0 R/W XXXXXXXXB 007931H Output Compare 0 OCCP0 R/W 007932H Output Compare 1 OCCP1 R/W 007933H Output Compare 1 OCCP1 R/W XXXXXXXXB 007934H Output Compare 2 OCCP2 R/W XXXXXXXXB 007935H Output Compare 2 OCCP2 R/W 007936H Output Compare 3 OCCP3 R/W 007937H Output Compare 3 OCCP3 R/W XXXXXXXXB 007938H Output Compare 4 OCCP4 R/W XXXXXXXXB 007939H Output Compare 4 OCCP4 R/W 00793AH Output Compare 5 OCCP5 R/W 00793BH Output Compare 5 OCCP5 R/W XXXXXXXXB 00793CH Output Compare 6 OCCP6 R/W XXXXXXXXB 00793DH Output Compare 6 OCCP6 R/W 00793EH Output Compare 7 OCCP7 R/W 00793FH Output Compare 7 OCCP7 R/W XXXXXXXXB 007940H Timer Data 0 TCDT0 R/W 00000000B 007941H Timer Data 0 TCDT0 R/W 007942H Timer Control Status 0 TCCSL0 R/W 007943H Timer Control Status 0 TCCSH0 R/W 0XXXXXXXB 007944H Timer Data 1 TCDT1 R/W 00000000B 007945H Timer Data 1 TCDT1 R/W 007946H Timer Control Status 1 TCCSL1 R/W 007947H Timer Control Status 1 TCCSH1 R/W 007948H Timer 0/Reload 0 TMR0/ TMRLR0 R/W Timer 1/Reload 1 TMR1/ TMRLR1 R/W Timer 2/Reload 2 TMR2/ TMRLR2 R/W Timer 3/Reload 3 TMR3/ TMRLR3 R/W Address 007949H 00794AH 00794BH 00794CH 00794DH 00794EH 00794FH Register R/W R/W R/W R/W Resource name Initial value XXXXXXXXB Input Capture 6/7 Output Compare 0/1 Output Compare 2/3 Output Compare 4/5 Output Compare 6/7 I/O Timer 0 I/O Timer 1 XXXXXXXXB XXXXXXXXB XXXXXXXXB XXXXXXXXB XXXXXXXXB XXXXXXXXB XXXXXXXXB XXXXXXXXB XXXXXXXXB XXXXXXXXB 00000000B 00000000B 00000000B 00000000B 0XXXXXXXB 16-bit Reload Timer 0 XXXXXXXXB 16-bit Reload Timer 1 XXXXXXXXB 16-bit Reload Timer 2 XXXXXXXXB 16-bit Reload Timer 3 XXXXXXXXB XXXXXXXXB XXXXXXXXB XXXXXXXXB XXXXXXXXB (Continued) 34 MB90860E Series Abbreviation Access 007950H Serial Mode Register 3 SMR3 W,R/W 00000000B 007951H Serial Control Register 3 SCR3 W,R/W 00000000B RDR3/ TDR3 R/W 00000000B SSR3 R,R/W Extended Communication Control Register 3 ECCR3 R,W, R/W 007955H Extended Status Control Register ESCR3 R/W 00000100B 007956H Baud Rate Generator Register 30 BGR30 R/W 00000000B 007957H Baud Rate Generator Register 31 BGR31 R/W 00000000B 007958H Serial Mode Register 4 SMR4 W,R/W 00000000B 007959H Serial Control Register 4 SCR4 W,R/W 00000000B RDR4/ TDR4 R/W 00000000B SSR4 R,R/W Extended Communication Control Register 4 ECCR4 R,W, R/W 00795DH Extended Status Control Register ESCR4 R/W 00000100B 00795EH Baud Rate Generator Register 40 BGR40 R/W 00000000B 00795FH Baud Rate generator Register 41 BGR41 R/W 00000000B Address 007952H Register Reception/Transmission Data Register 3 007953H Serial Status Register 3 007954H 00795AH Reception/Transmission Data Register 4 00795BH Serial Status Register 4 00795CH 007960H to 00796BH Resource name UART3 Initial value 00001000B 000000XXB UART4 00001000B 000000XXB Reserved 00796CH Clock Output Enable Register 00796DH to 00796FH CLKR R/W Clock Monitor XXXX0000B Reserved 007970H I2C Bus Status Register 0 IBSR0 R 00000000B 007971H I2C bus Control Register 0 IBCR0 W,R/W 00000000B 007972H ITBAL0 R/W 00000000B ITBAH0 R/W 007973H I2C 10-bit Slave Address Register 0 007974H I2C 10-bit Slave Address Mask 007975H Register 0 ITMKL0 R/W 00000000B 2 I C Interface 0 11111111B ITMKH0 R/W 00111111B 2 ISBA0 R/W 00000000B 2 007977H I C 7-bit Slave Address Mask Register 0 ISMK0 R/W 01111111B 007978H I2C Data Register 0 IDAR0 R/W 00000000B 007976H I C 7-bit Slave Address Register 0 007979H, 00797AH Reserved (Continued) 35 MB90860E Series Address Register 00797BH I2C Clock Control Register 0 00797CH to 00797FH Abbreviation Access Resource name Initial value ICCR0 R/W I2C Interface 0 00011111B Reserved 007980H I2C Bus Status Register 1 IBSR1 R 00000000B 007981H I2C Bus Control Register 1 IBCR1 W,R/W 00000000B 007982H ITBAL1 R/W 00000000B ITBAH1 R/W 007983H I2C 10-bit Slave Address Register 1 007984H I C 10-bit Slave Address Mask 007985H Register 1 2 R/W I C Interface 1 11111111B ITMKH1 R/W 00111111B 2 ISBA1 R/W 00000000B 2 ISMK1 R/W 01111111B 2 IDAR1 R/W 00000000B 007986H I C 7-bit Slave Address Register 1 007987H I C 7-bit Slave Address Mask Register 1 007988H I C Data Register 1 007989H, 00798AH Reserved 00798BH I2C Clock Control Register 1 00798CH to 0079C1H 0079C2H ITMKL1 00000000B 2 R/W I2C Interface 1 00011111B R, R/W Clock modulator (using prohibited) 0001X000B ICCR1 Reserved Clock modulator control register (setting prohibited) 0079C3H to 0079DFH CMCR Reserved 0079E0H Detect Address Setting 0 PADR0 R/W XXXXXXXXB 0079E1H Detect Address Setting 0 PADR0 R/W XXXXXXXXB 0079E2H Detect Address Setting 0 PADR0 R/W XXXXXXXXB 0079E3H Detect Address Setting 1 PADR1 R/W XXXXXXXXB Address Match Detection 0 0079E4H Detect Address Setting 1 PADR1 R/W 0079E5H Detect Address Setting 1 PADR1 R/W XXXXXXXXB 0079E6H Detect Address Setting 2 PADR2 R/W XXXXXXXXB 0079E7H Detect Address Setting 2 PADR2 R/W XXXXXXXXB 0079E8H Detect Address Setting 2 PADR2 R/W XXXXXXXXB 0079E9H to 0079EFH XXXXXXXXB Reserved (Continued) 36 MB90860E Series (Continued) Abbreviation Access 0079F0H Detect Address Setting 3 PADR3 R/W XXXXXXXXB 0079F1H Detect Address Setting 3 PADR3 R/W XXXXXXXXB 0079F2H Detect Address Setting 3 PADR3 R/W XXXXXXXXB 0079F3H Detect Address Setting 4 PADR4 R/W Address Register Resource name Initial value XXXXXXXXB Address Match Detection 1 0079F4H Detect Address Setting 4 PADR4 R/W 0079F5H Detect Address Setting 4 PADR4 R/W XXXXXXXXB 0079F6H Detect Address Setting 5 PADR5 R/W XXXXXXXXB 0079F7H Detect Address Setting 5 PADR5 R/W XXXXXXXXB 0079F8H Detect Address Setting 5 PADR5 R/W XXXXXXXXB 0079F9H to 007FFFH XXXXXXXXB Reserved Notes : * Initial value of "X" represents unknown value. * Any write access to reserved addresses in I/O map should not be performed. A read access to reserved addresses results in reading "X". 37 MB90860E Series INTERRUPT FACTORS, INTERRUPT VECTORS, INTERRUPT CONTROL REGISTER EI2OS clear DMA ch number Reset N INT9 instruction Interrupt cause Interrupt vector Interrupt control register Number Address Number Address #08 FFFFDCH N #09 FFFFD8H Exception N #10 FFFFD4H (Reserved) N #11 FFFFD0H (Reserved) N #12 FFFFCCH ICR00 0000B0H Input Capture 6 Y1 #13 FFFFC8H Input Capture 7 Y1 #14 FFFFC4H ICR01 0000B1H I2C0 N #15 FFFFC0H (Reserved) N #16 FFFFBCH ICR02 0000B2H 16-bit Reload Timer 0 Y1 0 #17 FFFFB8H 16-bit Reload Timer 1 Y1 1 #18 FFFFB4H ICR03 0000B3H 16-bit Reload Timer 2 Y1 2 #19 FFFFB0H 16-bit Reload Timer 3 Y1 #20 FFFFACH ICR04 0000B4H PPG 0/1/4/5 N #21 FFFFA8H PPG 2/3/6/7 N #22 FFFFA4H ICR05 0000B5H PPG 8/9/C/D N #23 FFFFA0H PPG A/B/E/F N #24 FFFF9CH ICR06 0000B6H Time Base Timer N #25 FFFF98H External Interrupt 0 to 3, 8 to 11 Y1 3 #26 FFFF94H ICR07 0000B7H Watch Timer N #27 FFFF90H External Interrupt 4 to 7, 12 to 15 Y1 4 #28 FFFF8CH ICR08 0000B8H 8/10-bit A/D Converter Y1 5 #29 FFFF88H I/O Timer 0, I/O Timer 1 N #30 FFFF84H ICR09 0000B9H Input Capture 4/5, I2C1 Y1 6 #31 FFFF80H Output Compare 0/1/4/5 Y1 7 #32 FFFF7CH ICR10 0000BAH Input Capture 0 to 3 Y1 8 #33 FFFF78H Output Compare 2/3/6/7 Y1 9 #34 FFFF74H ICR11 0000BBH UART 0 Reception Y2 10 #35 FFFF70H UART 0 Transmission Y1 11 #36 FFFF6CH ICR12 0000BCH UART 1 Reception / UART 3 Reception Y2 12 #37 FFFF68H UART 1 Transmission / UART 3 Transmission ICR13 0000BDH Y1 13 #38 FFFF64H (Continued) 38 MB90860E Series (Continued) Interrupt vector EI2OS clear DMA ch number UART 2 Reception / UART 4 Reception Y2 14 UART 2 Transmission / UART 4 Transmission Y1 15 #40 FFFF5CH Flash Memory N #41 FFFF58H Delayed interrupt N #42 FFFF54H Interrupt cause Number Address #39 FFFF60H Interrupt control register Number Address ICR14 0000BEH ICR15 0000BFH Y1 : Usable Y2 : Usable, with EI2OS stop function N : Unusable Notes : * The peripheral resources sharing the ICR register have the same interrupt level. * When two peripheral resources share the ICR register, only one can use Extended Intelligent I/O Service at a time. * When either of the two peripheral resources sharing the ICR register specifies Extended Intelligent I/O Service, the other one cannot use interrupts. 39 MB90860E Series ELECTRICAL CHARACTERISTICS 1. Absolute Maximum Ratings Parameter Symbol Rating Unit Remarks Min Max VCC VSS - 0.3 VSS + 6.0 V AVCC VSS - 0.3 VSS + 6.0 V VCC = AVCC*2 AVRH, AVRL VSS - 0.3 VSS + 6.0 V AVCC AVRH, AVCC AVRL, AVRH AVRL Input voltage*1 VI VSS - 0.3 VSS + 6.0 V *3 Output voltage*1 VO VSS - 0.3 VSS + 6.0 V *3 ICLAMP -4.0 +4.0 mA *5 |ICLAMP| 40 mA *5 IOL 15 mA *4 "L" level average output current IOLAV 4 mA *4 "L" level maximum overall output current IOL 100 mA *4 "L" level average overall output current IOLAV 50 mA *4 IOH -15 mA *4 "H" level average output current IOHAV -4 mA *4 "H" level maximum overall output current IOH -100 mA *4 "H" level average overall output current IOHAV -50 mA *4 Power consumption PD 340 mW Operating temperature TA -40 +105 C TSTG -55 +150 C Power supply voltage*1 Maximum Clamp Current Total Maximum Clamp Current "L" level maximum output current "H" level maximum output current Storage temperature *1 : This parameter is based on VSS = AVSS = 0 V. *2 : Set AVCC and VCC to the same voltage. Make sure that AVCC does not exceed VCC and that the voltage at the analog inputs does not exceed AVCC when the power is switched on. *3 : VI and VO should not exceed VCC + 0.3 V. VI should not exceed the specified ratings. However if the maximum current to/from an input is limited by some means with external components, the ICLAMP rating supersedes the VI rating. *4 : Applicable to pins : P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, P60 to P67, P70 to P77, P80 to P87, P90 to P97, PA0 to PA1 (Continued) 40 MB90860E Series (Continued) *5 : * Applicable to pins: P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57 (evaluation device : P50 to P55) , P60 to P67, P70 to P77, P80 to P87, P90 to P97, PA0 to PA1 * Use within recommended operating conditions. * Use at DC voltage (current) * The +B signal should always be applied a limiting resistance placed between the +B signal and the microcontroller. * The value of the limiting resistance should be set so that when the +B signal is applied the input current to the microcontroller pin does not exceed rated values, either instantaneously or for prolonged periods. * Note that when the microcontroller drive current is low, such as in the power saving modes, the +B input potential may pass through the protective diode and increase the potential at the VCC pin, and this may affect other devices. * Note that if a +B signal is input when the microcontroller power supply is off (not fixed at 0 V) , the power supply is provided from the pins, so that incomplete operation may result. * Note that if the +B input is applied during power-on, the power supply is provided from the pins and the resulting supply voltage may not be sufficient to operate the power-on reset. * Care must be taken not to leave the +B input pin open. * Sample recommended circuits: * Input/output equivalent circuits Protective diode VCC Limiting resistance P-ch +B input (0 V to 16 V) N-ch R WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings. 41 MB90860E Series 2. Recommended Conditions (VSS = AVSS = 0 V) Parameter Power supply voltage Symbol VCC, AVCC Value Unit Remarks Min Typ Max 4.0 5.0 5.5 V Under normal operation 3.5 5.0 5.5 V Under normal operation, when not using the A/D converter and not Flash programming. 4.5 5.0 5.5 V When External bus is used. 3.0 5.5 V Maintains RAM data in stop mode Use a ceramic capacitor or capacitor of better AC characteristics. Capacitor at the VCC should be greater than this capacitor. Smooth capacitor CS 0.1 1.0 F Operating temperature TA -40 +105 C C CS C Pin Connection Diagram WARNING: The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All of the device's electrical characteristics are warranted when the device is operated within these ranges. Always use semiconductor devices within their recommended operating condition ranges. Operation outside these ranges may adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users considering application outside the listed conditions are advised to contact their FUJITSU representatives beforehand. 42 MB90860E Series 3. DC Characteristics (TA = -40 C to +105 C, VCC = 5.0 V 10%, fCP 24 MHz, VSS = AVSS = 0 V) Parameter Input H voltage (At VCC = 5 V 10%) Input L voltage (At VCC = 5 V 10%) Symbol Pin Condition Value Min Typ Max Unit Remarks VIHS 0.8 VCC VCC + 0.3 V Port inputs if CMOS hysteresis input levels are selected (except P12, P44, P45, P46, P47, P50, P82, P83) VIHA 0.8 VCC VCC + 0.3 V Port inputs if Automotive input levels are selected VIHT 2.0 VCC + 0.3 V Port inputs if TTL input levels are selected VIHS 0.7 VCC VCC + 0.3 V P12, P50, P82, P85 inputs if CMOS input levels are selected VIHI 0.7 VCC VCC + 0.3 V P44, P45, P46, P47 inputs if CMOS hysteresis input levels are selected VIHR 0.8 VCC VCC + 0.3 V RST input pin (CMOS hysteresis) VIHM VCC - 0.3 VCC + 0.3 V MD input pin VILS VSS - 0.3 0.2 VCC V Port inputs if CMOS hysteresis input levels are selected (except P12, P44, P45, P46, P47, P50, P82, P83) VILA VSS - 0.3 0.5 VCC V Port inputs if Automotive input levels are selected VILT VSS - 0.3 0.8 V Port inputs if TTL input levels are selected VILS VSS - 0.3 0.3 VCC V P12, P50, P82, P85 inputs if CMOS input levels are selected VILI VSS - 0.3 0.3 VCC V P44, P45, P46, P47 inputs if CMOS hysteresis input levels are selected VILR VSS - 0.3 0.2 VCC V RST input pin (CMOS hysteresis) VILM VSS - 0.3 VSS + 0.3 V MD input pin Output H voltage VOH Normal outputs VCC = 4.5 V, VCC - 0.5 IOH = -4.0 mA V Output H voltage VOHI I2C current VCC = 4.5 V, VCC - 0.5 outputs IOH = -3.0 mA V Output L voltage VOL Normal outputs VCC = 4.5 V, IOL = 4.0 mA 0.4 V Output L voltage VOLI I2C current VCC = 4.5 V, outputs IOL = 3.0 mA 0.4 V (Continued) 43 MB90860E Series (Continued) Parameter (TA = -40 C to +105 C, VCC = 5.0 V 10%, fCP 24 MHz, VSS = AVSS = 0 V) Symbol Pin Condition Typ Max -1 +1 A Pull-up resistance RUP P00 to P07, P10 to P17, P20 to P27, P30 to P37, RST 25 50 100 k Pull-down resistance RDOWN MD2 25 50 100 Except k Flash devices VCC = 5.0 V, Internal frequency : 24 MHz, At normal operation. 55 70 mA VCC = 5.0 V, Internal frequency : 24 MHz, At writing FLASH memory. 70 85 mA Flash devices VCC = 5.0 V, Internal frequency : 24 MHz, At erasing FLASH memory. 75 90 mA Flash devices ICCS VCC = 5.0 V, Internal frequency : 24 MHz, At Sleep mode. 25 35 mA ICTS VCC = 5.0 V, Internal frequency : 2 MHz, At Main Timer mode 0.3 0.8 mA VCC = 5.0 V, Internal frequency : 24 MHz, At PLL Timer mode, external frequency = 4 MHz 4 7 mA ICCL VCC = 5.0 V Internal frequency : 8 kHz, At sub operation TA = +25C 70 140 A ICCLS VCC = 5.0 V Internal frequency : 8 kHz, At sub sleep TA = +25C 20 50 A ICCT VCC = 5.0 V Internal frequency : 8 kHz, At watch mode TA = +25C 10 35 A ICCH VCC = 5.0 V, At Stop mode, TA = +25C 7 25 A 5 15 pF ICC Power supply current* Input capacity ICTSPLL6 CIN VCC Other than C, AVCC, AVSS, AVRH, AVRL, VCC, VSS, * : The power supply current is measured with an external clock. 44 Unit Remarks Min IIL Input leak current VCC = 5.5 V, VSS < VI < VCC Value MB90860E Series 4. AC Characteristics (1) Clock Timing (TA = -40 C to +105 C, VCC = 5.0 V 10%, fCP 24 MHz, VSS = AVSS = 0 V) Parameter Symbol Value Pin Unit Remarks Min Typ Max X0, X1 3 16 MHz When using an oscillation circuit X0, X1 3 24 MHz When using an external clock* X0A, X1A -- 32.768 100 kHz X0, X1 62.5 333 ns When using an oscillation circuit X0, X1 41.67 333 ns When using an external clock tCYLL X0A, X1A 10 30.5 -- s PWH, PWL X0 10 ns PWHL, PWLL X0A 5 15.2 s Duty ratio is about 30% to 70%. Input clock rise and fall time tCR, tCF X0 5 ns When using external clock Internal operating clock frequency (machine clock) fCP 1.5 24 MHz When using main clock fCPL 8.192 50 kHz When using sub clock tCP 41.67 666 ns When using main clock tCPL 20 122.1 s When using sub clock fC Clock frequency fCL tCYL Clock cycle time Input clock pulse width Internal operating clock cycle time (machine clock) * : When selecting the PLL clock, the range of clock frequency is limited. Use this product within range as mentioned in "Relation among external clock frequency and machine clock frequency". tCYL 0.8 VCC X0 0.2 VCC PWH PWL tCF tCR tCYLL 0.8 VCC X0A 0.2 VCC PWHL PWLL tCF tCR Clock Timing 45 MB90860E Series * Guaranteed PLL operation range Guaranteed operation range Power supply voltage VCC (V) 5.5 Guaranteed A/D Converter operation range 4.0 3.5 Guaranteed PLL operation range 1.5 24 4 Machine clock fCP (MHz) Guaranteed operation range of MB90860E series Guaranteed oscillation frequency range x6 Internal clock fCP (MHz) 24 x4 x3 x2 x1 16 x 1/2 (PLL off) 12 8 4.0 1.5 3 4 8 12 16 24 External clock fC (MHz) * * : When using crystal oscillator or ceramic oscillator, the maximum oscillation clock frequency is 16 MHz 46 MB90860E Series (2) Reset Standby Input (TA = -40 C to +105 C, VCC = 5.0 V 10%, fCP 24 MHz, VSS = AVSS = 0.0 V) Parameter Reset input time Symbol tRSTL Pin RST Value Unit Remarks Min Max 500 ns Under normal operation Oscillation time of oscillator* + 100 s ns In Stop mode, Sub Clock mode, Sub Sleep mode and Watch mode 100 s In Time Timer mode * : Oscillation time of oscillator is the time that the amplitude reaches 90%. In the crystal oscillator, the oscillation time is between several ms and to tens of ms. In ceramic oscillators, the oscillation time is between hundreds of s to several ms. With an external clock, the oscillation time is 0 ms. Under normal operation: tRSTL RST 0.2 VCC 0.2 VCC In Stop mode, Sub Clock mode, Sub Sleep mode, Watch mode, Power-on: tRSTL RST 0.2 VCC X0 0.2 VCC 90% of amplitude Internal operation clock 100 s Oscillation time of oscillator Oscillation stabilization waiting time Instruction execution Internal reset 47 MB90860E Series (3) Power On Reset (TA = -40 C to +105 C, VCC = 5.0 V 10%, fCP 24 MHz, VSS = AVSS = 0.0 V) Parameter Symbol Pin Power on rise time tR VCC tOFF VCC Power off time Value Condition Unit Min Max 0.05 30 ms 1 ms Remarks Due to repetitive operation tR 2.7 V VCC 0.2 V 0.2 V 0.2 V tOFF If you change the power supply voltage too rapidly, a power on reset may occur. We recommend that you startup smoothly by restraining voltages when changing the power supply voltage during operation, as shown in the figure below. Perform while not using the PLL clock. However, if voltage drops are within 1 V/s, you can operate VCC We recommend a rise of 50 mV/ms maximum. 3V Holds RAM data VSS (4) Clock Output Timing (TA = -40 C to +105 C, VCC = 5.0 V 10%, VSS = 0.0 V, fCP 24 MHz) Parameter Symbol Pin Condition Cycle time tCYC CLK CLK CLK tCHCL CLK Value Unit Max 62.5 ns fCP = 16 MHz 41.76 ns fCP = 24 MHz 20 ns fCP = 16 MHz 13 ns fCP = 24 MHz tCYC tCHCL CLK 2.4 V 2.4 V 0.8 V 48 Remarks Min MB90860E Series (5) Bus Timing (Read) Parameter Symbol (TA = -40 C to +105 C, VCC = 5.0 V 10%, VSS = 0.0 V, fCP 24 MHz) Value Pin Condition Unit Min Max ALE pulse width tLHLL ALE tCP/2 - 10 ns Valid address ALE time tAVLL ALE, A23 to A16, AD15 to AD00 tCP/2 - 20 ns ALE Address valid time tLLAX ALE, AD15 to AD00 tCP/2 - 15 ns Valid address RD time tAVRL A23 to A16, AD15 to AD00, RD tCP - 15 ns Valid address Valid data input tAVDV A23 to A16, AD15 to AD00 5 tCP/2 - 60 ns RD pulse width tRLRH RD 3 tCP/2 - 20 ns RD Valid data input tRLDV RD, AD15 to AD00 3 tCP/2 - 50 ns RD Data hold time tRHDX RD, AD15 to AD00 0 ns RD ALE time tRHLH RD, ALE tCP/2 - 15 ns RD Address valid time tRHAX RD, A23 to A16 tCP/2 - 10 ns Valid address CLK time tAVCH A23 to A16, AD15 to AD00, CLK tCP/2 - 16 ns RD CLK time tRLCH RD, CLK tCP/2 - 15 ns ALE RD time tLLRL ALE, RD tCP/2 - 15 ns tRLCH tAVCH 2.4 V CLK 2.4 V tLLAX tAVLL ALE 2.4 V tRHLH 2.4 V 2.4 V 0.8 V tLHLL tAVRL tRLRH 2.4 V RD 0.8 V tLLRL tRHAX 2.4 V A23 to A16 2.4 V 0.8 V 0.8 V tRLDV tRHDX tAVDV AD15 to AD00 2.4 V 0.8 V 2.4 V Address 0.8 V VIH VIL VIH Read data VIL 49 MB90860E Series (6) Bus Timing (Write) Parameter (TA = -40 C to +105 C, VCC = 5.0 V 10%, VSS = 0.0 V, fCP 24 MHz) Value Symbol Pin Condition Unit Min Max Valid address WR time tAVWL A23 to A16, AD15 to AD00, WR WR pulse width tWLWH WR Valid data output WR time tDVWH AD15 to AD00, WR WR Data hold time tWHDX WR Address valid time tCP-15 ns 3 tCP/2 - 20 ns 3 tCP/2 - 20 ns AD15 to AD00, WR 15 ns tWHAX A23 to A16, WR tCP/2 - 10 ns WR ALE time tWHLH WR, ALE tCP/2 - 15 ns WR CLK time tWLCH WR, CLK tCP/2 - 15 ns tWLCH 2.4 V CLK tWHLH 2.4 V ALE tAVWL tWLWH 2.4 V WR (WRL, WRH) 0.8 V tWHAX A23 to A16 2.4 V 2.4 V 0.8 V 0.8 V tDVWH AD15 to AD00 2.4 V 0.8 V 50 2.4 V 2.4 V Address 0.8 V tWHDX Write data 0.8 V MB90860E Series (7) Ready Input Timing Parameter Symbol (TA = -40 C to +105 C, VCC = 5.0 V 10%, VSS = 0.0 V, fCP 24 MHz) Rated Value Test Pin Units Remarks Condition Min Max RDY setup time tRYHS RDY RDY hold time tRYHH RDY 45 ns fCP = 16 MHz 32 ns fCP = 24 MHz 0 ns Note : If the RDY setup time is insufficient, use the auto-ready function. 2.4 V CLK ALE RD/WR RDY When WAIT is not used. RDY When WAIT is used. tRYHS tRYHH VIH VIH VIL 51 MB90860E Series (8) Hold Timing Parameter (TA = -40 C to +105 C, VCC = 5.0 V 10%, VSS = 0.0 V, fCP 24 MHz) Value Symbol Pin Condition Units Min Max Pin floating HAK time tXHAL HAK HAK time Pin valid time tHAHV HAK 30 tCP ns tCP 2 tCP ns Note : There is more than 1 cycle from when HRQ reads in until the HAK is changed. 2.4 V HAK 0.8 V tHAHV tXHAL Each pin 2.4 V 0.8 V 52 High-Z 2.4 V 0.8 V MB90860E Series (9) UART0/1/2/3/4 Parameter (TA = -40 C to +105 C, VCC = 5.0 V 10%, VSS = 0.0 V, fCP 24 MHz) Value Symbol Pin Condition Unit Min Max 8 tCP ns -80 +80 ns 100 ns SCK0 to SCK4, SIN0 to SIN4 60 ns tSHSL SCK0 to SCK4 4 tCP ns Serial clock "L" pulse width tSLSH SCK0 to SCK4 4 tCP ns SCK SOT delay time tSLOV SCK0 to SCK4, SOT0 to SOT4 150 ns Valid SIN SCK tIVSH SCK0 to SCK4, SIN0 to SIN4 60 ns SCK Valid SIN hold time tSHIX SCK0 to SCK4, SIN0 to SIN4 60 ns Serial clock cycle time tSCYC SCK0 to SCK4 SCK SOT delay time tSLOV SCK0 to SCK4, SOT0 to SOT4 Valid SIN SCK tIVSH SCK0 to SCK4, SIN0 to SIN4 SCK Valid SIN hold time tSHIX Serial clock "H" pulse width Internal clock operation output pins are CL = 80 pF + 1 TTL. External clock operation output pins are CL = 80 pF + 1 TTL. Notes : * AC characteristic in CLK synchronized mode. * CL is load capacity value of pins when testing. tSCYC SCK 2.4 V 0.8 V 0.8 V tSLOV SOT 2.4 V 0.8 V tIVSH SIN tSHIX VIH VIH VIL VIL Internal Shift Clock Mode 53 MB90860E Series tSLSH tSHSL VIH VIH SCK VIL VIL tSLOV 2.4 V SOT 0.8 V tIVSH SIN tSHIX VIH VIH VIL VIL External Shift Clock Mode (10) Trigger Input Timing Parameter Input pulse width Symbol tTRGH tTRGL (TA = -40 C to +105 C, VCC = 5.0 V 10%, fCP 24 MHz, VSS = 0.0 V) Value Pin Condition Unit Min Max INT0 to INT15, INT0R to INT15R, ADTG 54 5 tCP VIH VIH INT0 to INT15, INT0R to INT15R, ADTG VIL VIL tTRGH tTRGL ns MB90860E Series (11) Timer Related Resource Input Timing (TA = -40 C to +105 C, VCC = 5.0 V 10%, fCP 24 MHz, VSS = 0 V) Value Parameter Symbol Pin Condition Unit Min Max tTIWH Input pulse width TIN0 to TIN3, IN0 to IN7 tTIWL 4 tCP ns VIH VIH TIN0 to TIN3, IN0 to IN7 VIL VIL tTIWH tTIWL (12) Timer Related Resource Output Timing (TA = -40C to +105C, VCC = 5.0 V 10%, fCP 24 MHz, VSS = 0.0 V) Value Parameter Symbol Pin Condition Unit Min Max CLK TOUT change time CLK TOT0 to TOT3, PPG0 to PPGF tTO 30 ns 2.4 V 2.4 V TOT0 to TOT3, PPG0 to PPGF 0.8 V tTO 55 MB90860E Series (13) I2C Timing Parameter Symbol (TA = -40C to +105C, VCC = 5.0 V 10%, VSS = 0.0 V) Standard-mode Fast-mode*1 Condition Unit Min Max Min Max fSCL 0 100 0 400 kHz tHDSTA 4.0 0.6 s "L" width of the SCL clock tLOW 4.7 1.3 s "H" width of the SCL clock tHIGH 4.0 0.6 s Set-up time for a repeated START condition SCL SDA tSUSTA 4.7 0.6 s Data hold time SCL SDA tHDDAT 0 3.45*3 0 0.9*4 s Data set-up time SDA SCL tSUDAT 250 100 ns Set-up time for STOP condition SCL SDA tSUSTO 4.0 0.6 s tBUS 4.7 1.3 s SCL clock frequency Hold time (repeated) START condition SDA SCL Bus free time between a STOP and START condition R = 1.7 k, C = 50 pF*2 *1 : For use at over 100 kHz, set the machine clock to at least 6 MHz. *2 : R,C : Pull-up resistor and load capacitor of the SCL and SDA lines. *3 : The maximum tHDDAT have only to be met if the device does not stretch the "L" width (tLOW) of the SCL signal. *4 : A Fast-mode I2C-bus device can be used in a Standard-mode I2C-bus system, but the requirement tSUDAT 250 ns must then be met. SDA tSUDAT tLOW tBUS tHDSTA SCL tHDSTA 56 tHDDAT tHIGH tSUSTA tSUSTO MB90860E Series 5. A/D Converter (TA = -40 C to +105 C, 3.0 V AVRH - AVRL, VCC = AVCC = 5.0 V 10%, fCP 24 MHz, VSS = AVSS = 0 V) Parameter Symbol Pin Resolution Total error Value Unit Min Typ Max 10 bit 3.0 LSB Nonlinearity error 2.5 LSB Differential nonlinearity error 1.9 LSB Zero reading voltage VOT AN0 to AN23 AVRL - 1.5 AVRL + 0.5 AVRL + 2.5 LSB Full scale reading voltage VFST AN0 to AN23 AVRH - 3.5 AVRH - 1.5 AVRH + 0.5 LSB Compare time Sampling time Analog port input current IAIN AN0 to AN23 Analog input voltage range VAIN Reference voltage range Power supply current 1.0 16500 s s -0.3 +0.3 A AN0 to AN23 AVRL AVRH V AVRH AVRL + 2.7 AVCC V AVRL 0 AVRH - 2.7 V IA AVCC 3.5 7.5 mA IAH AVCC 5 A 2.0 0.5 1.2 Reference voltage current IR AVRH 600 900 A IRH AVRH 5 A Offset between input channels AN0 to AN23 4 LSB Remarks 4.5 V AVCC 5.5 V 4.0 V AVCC < 4.5 V 4.5 V AVCC 5.5 V 4.0 V AVCC < 4.5 V * * * : IF A/D convertor is not operating, a current when CPU is stopped is applicable (VCC = AVCC = AVRH = 5.0 V) . Note : The accuracy gets worse as AVRH - AVRL becomes smaller. 57 MB90860E Series 6. Definition of A/D Converter Terms Resolution Non linearity error Differential linearity error Total error Zero reading voltage Full scale reading voltage : Analog variation that is recognized by an A/D converter. : Deviation between a line across zero-transition line ( "00 0000 0000" "00 0000 0001" ) and full-scale transition line ( "11 1111 1110" "11 1111 1111" ) and actual conversion characteristics. : Deviation of input voltage, which is required for changing output code by 1 LSB, from an ideal value. : Difference between an actual value and an ideal value. A total error includes zero transition error, full-scale transition error, and linear error. : Input voltage which results in the minimum conversion value. : Input voltage which results in the maximum conversion value. Total error 3FFH 3FEH 1.5 LSB Actual conversion characteristics Digital output 3FDH {1 LSB x (N - 1) + 0.5 LSB} 004H VNT (Actually-measured value) 003H Actual conversion characteristics Ideal characteristics 002H 001H 0.5 LSB AVRL AVRH Analog input VNT - {1 LSB x (N - 1) + 0.5 LSB} 1 LSB AVRH - AVRL 1 LSB (Ideal value) = [V] 1024 VOT (Ideal value) = AVRL + 0.5 LSB [V] Total error of digital output "N" = [LSB] VFST (Ideal value) = AVRH - 1.5 LSB [V] VNT : A voltage at which digital output transitions from (N - 1) to N. (Continued) 58 MB90860E Series (Continued) Non linearity error Differential linearity error Ideal characteristics 3FFH Actual conversion characteristics {1 LSB x (N - 1) + VOT } Digital output 3FDH N + 1H VFST (actual measurement value) VNT (actual measurement value) 004H Actual conversion characteristics 003H Digital output 3FEH Actual conversion characteristics NH V (N + 1) T (actual measurement value) VNT (actual measurement value) N - 1H 002H Ideal characteristics Actual conversion characteristics N - 2H 001H VOT (actual measurement value) AVRL AVRH AVRL AVRH Analog input Analog input Non linearity error of digital output N = Differential linearity error of digital output N = 1 LSB = VNT - {1 LSB x (N - 1) + VOT} 1 LSB V (N+1) T - VNT 1 LSB VFST - VOT 1022 [LSB] -1 LSB [LSB] [V] VOT : Voltage at which digital output transits from "000H" to "001H." VFST : Voltage at which digital output transits from "3FEH" to "3FFH." 59 MB90860E Series 7. Notes on A/D Converter Section Use the device with external circuits of the following output impedance for analog inputs : Recommended output impedance of external circuits are : Approx. 1.5 k or lower (4.0 V AVCC 5.5 V, sampling period 0.5 s) If an external capacitor is used, in consideration of the effect by tap capacitance caused by external capacitors and on-chip capacitors, capacitance of the external one is recommended to be several thousand times as high as internal capacitor. If output impedance of an external circuit is too high, a sampling period for an analog voltage may be insufficient. * Analog input circuit model R Analog input Comparator C 4.5 V AVCC 5.5 V : R =: 2.52 k, C =: 10.7 pF 4.0 V AVCC < 4.5 V : R =: 13.6 k, C =: 10.7 pF Note : Use the values in the figure only as a guideline. 8. Flash Memory Program/Erase Characteristics Parameter Conditions Sector erase time Chip erase time TA = +25 C VCC = 5.0 V Word (16-bit width) programming time Value Unit Remarks Min Typ Max 1 15 s Excludes programming prior to erasure 9 s Excludes programming prior to erasure 16 3600 s Except for the over head time of the system Programs/Erase cycle 10000 cycle Flash Data Retention Time Average TA = +85 C 20 Year * * : This value comes from the technology qualification (using Arrhenius equation to translate high temperature measurements into normalized value at +85 C) . 60 MB90860E Series EXAMPLE CHARACTERISTICS * MB90F867E, MB90F867ES ICC - VCC ICCL - VCC TA = +25 C, at external clock operating f = Internal operation frequency TA = +25 C, at external clock operating f = Internal operation frequency 100 90 80 70 60 50 40 30 20 10 0 70 60 ICC (mA) f = 20 MHz 40 f = 16 MHz f = 12 MHz f = 10 MHz f = 8 MHz f = 4 MHz f = 2 MHz 30 20 10 0 2.5 3.5 4.5 5.5 ICCL ( A) f = 24 MHz 50 6.5 f = 8 kHz 2.5 3.5 ICCS - VCC 30 ICCS (mA) f = 20 MHz 20 f = 16 MHz f = 12 MHz f = 10 MHz f = 8 MHz 15 10 5 ICCLS ( A) f = 24 MHz 25 f = 4 MHz f = 2 MHz 3.5 4.5 5.5 6.5 50 45 40 35 30 25 20 15 10 5 0 f = 8 kHz 2.5 3.5 ICCT - VCC TA = +25 C, at external clock operating f = Internal operation frequency f = 2 MHz 200 150 ICCT ( A) 300 250 100 50 4.5 5.5 6.5 20 18 16 14 12 10 8 6 4 2 0 f = 8 kHz 2.5 3.5 VCC (V) 4.5 5.5 ICCH - VCC f = 24 MHz 3.5 4.5 VCC (V) 5.5 6.5 TA = +25 C, at stop ICCH ( A) ICTSPLL6 (mA) TA = +25 C, at external clock operating f = Internal operation frequency 2.5 6.5 VCC (V) ICTSPLL6 - VCC 10 9 8 7 6 5 4 3 2 1 0 6.5 TA = +25 C, at external clock operating f = Internal operation frequency 400 ICTS ( A) 5.5 ICTS - VCC 350 3.5 4.5 VCC (V) VCC (V) 0 2.5 6.5 TA = +25 C, at external clock operating f = Internal operation frequency 35 2.5 5.5 ICCLS - VCC TA = +25 C, at external clock operating f = Internal operation frequency 0 4.5 VCC (V) VCC (V) 10 9 8 7 6 5 4 3 2 1 0 2.5 3.5 4.5 5.5 6.5 VCC (V) 61 MB90860E Series * MB90867E, MB90867ES ICC - VCC ICCL - VCC TA = +25 C, at external clock operating f = Internal operation frequency TA = +25 C, at external clock operating f = Internal operation frequency 70 60 ICC (mA) f = 20 MHz f = 16 MHz 40 f = 12 MHz f = 10 MHz f = 8 MHz 30 20 f = 4 MHz f = 2 MHz 10 0 ICCL (A) f = 24 MHz 50 2.5 3.5 4.5 5.5 100 90 80 70 60 50 40 30 20 10 0 6.5 f = 8 kHz 2.5 3.5 ICCS - VCC f = 24 MHz 25 f = 20 MHz 20 f = 16 MHz 15 f = 12 MHz f = 10 MHz f = 8 MHz 45 40 35 30 25 20 15 10 5 0 10 f = 4 MHz 5 ICCLS (A) ICCS (mA) 50 30 f = 2 MHz 3.5 4.5 5.5 6.5 f = 8 kHz 2.5 3.5 VCC (V) ICCT - VCC TA = +25 C, at external clock operating f = Internal operation frequency f = 2 MHz 200 150 ICCT (A) ICTS (A) 300 100 50 4.5 5.5 6.5 20 18 16 14 12 10 8 6 4 2 0 f = 8 kHz 2.5 3.5 4.5 VCC (V) VCC (V) ICTSPLL6 - VCC ICCH - VCC f = 24 MHz 3.5 4.5 VCC (V) 62 5.5 6.5 5.5 6.5 TA = +25 C, at stop ICCH (A) ICTSPLL6 (mA) TA = +25 C, at external clock operating f = Internal operation frequency 2.5 6.5 ICTS - VCC 250 10 9 8 7 6 5 4 3 2 1 0 5.5 TA = +25 C, at external clock operating f = Internal operation frequency 400 3.5 4.5 VCC (V) 350 0 2.5 6.5 TA = +25 C, at external clock operating f = Internal operation frequency 35 2.5 5.5 ICCLS - VCC TA = +25 C, at external clock operating f = Internal operation frequency 0 4.5 VCC (V) VCC (V) 10 9 8 7 6 5 4 3 2 1 0 2.5 3.5 4.5 VCC (V) 5.5 6.5 MB90860E Series * I/O characteristics (VCC-VOH) - IOH VOL - IOL TA = +25 C, VCC = 4.5 V TA = +25 C, VCC = 4.5 V 800 600 VOL (mV) VCC VOH (mV) 700 500 400 300 200 100 0 0 1 2 3 4 5 7 6 8 9 1000 900 800 700 600 500 400 300 200 100 0 10 0 1 2 3 Automotive VIN - VCC VIN (V) VIN (V) 3.0 3.5 4.0 4.5 5.0 6 5.5 6.0 6.5 7.0 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 2.5 3.0 3.5 4.0 4.5 5.0 4.0 4.5 5.0 VCC (V) 6.0 6.5 7.0 UART-SIN pin, I2C pin TA = +25 C VIN (V) VIN (V) 5.5 CMOS VIN - VCC VIHT VILT 3.5 10 VCC (V) TA = +25 C 3.0 9 VILS TTL VIN - VCC 2.5 8 VIHS VCC (V) 2.5 2.3 2.0 1.8 1.5 1.3 1.0 0.8 0.5 0.3 0.0 7 UART-SIN pin, other than I2C pin TA = +25 C VIHA VILA 2.5 5 CMOS VIN - VCC TA = +25 C 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 4 IOL (mA) IOH (mA) 5.5 6.0 6.5 7.0 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 VIHS VILS 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 VCC (V) 63 MB90860E Series ORDERING INFORMATION Part number MB90F867EPF MB90F867ESPF MB90F867EPFV MB90F867ESPFV MB90867EPF MB90867ESPF MB90867EPFV MB90867ESPFV MB90V340E-101 MB90V340E-102 64 Package Remarks 100-pin Plastic QFP (FPT-100P-M06) Flash memory product 100-pin Plastic LQFP (FPT-100P-M05) 100-pin Plastic QFP (FPT-100P-M06) MASK ROM product 100-pin Plastic LQFP (FPT-100P-M05) 299-pin Ceramic PGA (PGA-299C-A01) Evaluation product MB90860E Series PACKAGE DIMENSIONS 100-pin plastic QFP Lead pitch 0.65 mm Package width x package length 14.00 x 20.00 mm Lead shape Gullwing Sealing method Plastic mold Mounting height 3.35 mm MAX Code (Reference) P-QFP100-14x20-0.65 (FPT-100P-M06) 100-pin plastic QFP (FPT-100P-M06) Note 1) * : These dimensions do not include resin protrusion. Note 2) Pins width and pins thickness include plating thickness. Note 3) Pins width do not include tie bar cutting remainder. 23.900.40(.941.016) * 20.000.20(.787.008) 80 51 81 50 0.10(.004) 17.900.40 (.705.016) *14.000.20 (.551.008) INDEX Details of "A" part 100 1 30 0.65(.026) 0.320.05 (.013.002) 0.13(.005) M "A" C 0.25(.010) +0.35 3.00 -0.20 +.014 .118 -.008 (Mounting height) 0~8 31 2002 FUJITSU LIMITED F100008S-c-5-5 0.170.06 (.007.002) 0.800.20 (.031.008) 0.880.15 (.035.006) 0.250.20 (.010.008) (Stand off) Dimensions in mm (inches). Note: The values in parentheses are reference values. Please confirm the latest Package dimension by following URL. http://edevice.fujitsu.com/fj/DATASHEET/ef-ovpklv.html (Continued) 65 MB90860E Series (Continued) 100-pin plastic LQFP Lead pitch 0.50 mm Package width x package length 14.0 x 14.0 mm Lead shape Gullwing Sealing method Plastic mold Mounting height 1.70 mm MAX Weight 0.65g Code (Reference) P-LFQFP100-14x14-0.50 (FPT-100P-M05) 100-pin plastic LQFP (FPT-100P-M05) Note 1) * : These dimensions do not include resin protrusion. Note 2) Pins width and pins thickness include plating thickness. Note 3) Pins width do not include tie bar cutting remainder. 16.000.20(.630.008)SQ * 14.000.10(.551.004)SQ 75 51 76 50 0.08(.003) Details of "A" part +0.20 100 26 1 25 C 0.200.05 (.008.002) 0.08(.003) M 0.1450.055 (.0057.0022) 2003 FUJITSU LIMITED F100007S-c-4-6 Please confirm the latest Package dimension by following URL. http://edevice.fujitsu.com/fj/DATASHEET/ef-ovpklv.html 66 0.100.10 (.004.004) (Stand off) 0~8 "A" 0.50(.020) +.008 1.50 -0.10 .059 -.004 (Mounting height) INDEX 0.500.20 (.020.008) 0.600.15 (.024.006) 0.25(.010) Dimensions in mm (inches). Note: The values in parentheses are reference values. MB90860E Series The information for microcontroller supports is shown in the following homepage. http://www.fujitsu.com/global/services/microelectronics/product/micom/support/index.html FUJITSU LIMITED All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU sales representatives before ordering. The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of Fujitsu semiconductor device; Fujitsu does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. Fujitsu assumes no liability for any damages whatsoever arising out of the use of the information. Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of Fujitsu or any third party or does Fujitsu warrant non-infringement of any third-party's intellectual property right or other right by using such information. Fujitsu assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein. The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite). Please note that Fujitsu will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the prior authorization by Japanese government will be required for export of those products from Japan. Edited Business Promotion Dept. F0610