For further information contact your local STMicroelectronics sales office.
September 2018 DB3692 Rev 1 1/4
STLINK-V3SET
STLINK-V3SET debugger/programmer for STM8 and STM32
Data brief
Features
•Stand-alone probe with modular extensions
•Self-powered through a USB connector
(Micro-B)
•USB 2.0 high-speed compatible interface
•Direct firmware update support (DFU)
•JTAG / serial wire debugging (SWD) specific
features:
– 3 V to 3.6 V application voltage support
and 5 V tolerant inputs
– Flat cables STDC14 to MIPI10 / STDC14 /
MIPI20 (connectors with 1.27 mm pitch)
– JTAG communication support
– SWD and serial wire viewer (SWV)
communication support
•SWIM specific features (only available with
adapter board MB1440):
– 1.65 V to 5.5 V application voltage support
– SWIM header (2.54 mm pitch)
– SWIM low-speed and high-speed modes
support
•Virtual COM port (VCP) specific features:
– 3 V to 3.6 V application voltage support on
the UART interface and 5 V tolerant inputs
– VCP frequency up to 15 MHz
– Available on STDC14 debug connector
(not available on MIPI10)
•Multi-path bridge USB to
SPI/UART/I2C/CAN/GPIOs specific features:
– 3 V to 3.6 V application voltage support
and 5 V tolerant inputs
– Signals available on adapter board only
(MB1440)
•Drag-and-drop Flash programming
•Two color LEDs: communication, power
Picture is not contractual.
Description
The STLINK-V3SET is a modular stand-alone
debugging and programming probe for the STM8
and STM32 microcontrollers. It is composed of a
main module and a complementary adapter
board.
The SWIM and JTAG/SWD interfaces are used to
communicate with any STM8 or STM32
microcontroller located on an application board.
The STLINK-V3SET also provides a Virtual COM
port interface allowing the host PC to
communicate with the target microcontroller
through one UART, and bridge interfaces (SPI,
I2C, CAN, GPIOs) allowing for instance the
programming of the target through bootloader.
The modular architecture of STLINK-V3SET
enables to extend its main features through
additional modules such as the adapter board.
www.st.com
General information STLINK-V3SET
2/4 DB3692 Rev 1
General information
The STLINK-V3SET embeds an STM32 32-bit microcontroller based on the Arm®(a)
Cortex®-M processor.
System requirements
•Windows® OS (7, 8 and 10), Linux® 64-bit, or macOS®(b)
•USB Type-A to Micro-B cable
Development toolchains
•Keil® MDK-ARM(c)
•IAR™ EWARM(c)
•GCC-based IDEs
Ordering information
To order the STLINK-V3SET, refer to Table 1.
a. Arm is a registered trademark of Arm Limited (or its subsidiaries) in the US and or elsewhere.
b. macOS® is a trademark of Apple Inc. registered in the U.S. and other countries.
c. On Windows® only.
Table 1. Ordering information
Order code Description
STLINK-V3SET STLINK-V3 modular in-circuit debugger and programmer for STM8 and
STM32.
DB3692 Rev 1 3/4
STLINK-V3SET Revision history
4
Revision history
Table 2. Document revision history
Date Revision Changes
6-Sep-2018 1 Initial release.
STLINK-V3SET
4/4 DB3692 Rev 1
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on
ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or
the design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2018 STMicroelectronics – All rights reserved
