MC14017B Decade Counter The MC14017B is a five-stage Johnson decade counter with built-in code converter. High speed operation and spike-free outputs are obtained by use of a Johnson decade counter design. The ten decoded outputs are normally low, and go high only at their appropriate decimal time period. The output changes occur on the positive-going edge of the clock pulse. This part can be used in frequency division applications as well as decade counter or decimal decode display applications. * * * * * * * * http://onsemi.com MARKING DIAGRAMS Fully Static Operation DC Clock Input Circuit Allows Slow Rise Times Carry Out Output for Cascading Divide-by-N Counting Supply Voltage Range = 3.0 Vdc to 18 Vdc Capable of Driving Two Low-power TTL Loads or One Low-power Schottky TTL Load Over the Rated Temperature Range Pin-for-Pin Replacement for CD4017B Triple Diode Protection on All Inputs 16 PDIP-16 P SUFFIX CASE 648 MC14017BCP AWLYYWW 1 16 SOIC-16 D SUFFIX CASE 751B 14017B AWLYWW 1 16 SOEIAJ-16 F SUFFIX CASE 966 MAXIMUM RATINGS (Voltages Referenced to VSS) (Note 2.) Symbol Value Unit - 0.5 to +18.0 V - 0.5 to VDD + 0.5 V Input or Output Current (DC or Transient) per Pin 10 mA PD Power Dissipation, per Package (Note 3.) 500 mW TA Ambient Temperature Range - 55 to +125 C Tstg Storage Temperature Range - 65 to +150 C TL Lead Temperature (8-Second Soldering) 260 C VDD Vin, Vout Iin, Iout Parameter DC Supply Voltage Range Input or Output Voltage Range (DC or Transient) 2. Maximum Ratings are those values beyond which damage to the device may occur. 3. Temperature Derating: Plastic "P and D/DW" Packages: - 7.0 mW/_C From 65_C To 125_C This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, Vin and Vout should be constrained to the range VSS (Vin or Vout) VDD. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either VSS or VDD). Unused outputs must be left open. v v Semiconductor Components Industries, LLC, 2000 March, 2000 - Rev. 3 1 MC14017B AWLYWW 1 A = Assembly Location WL or L = Wafer Lot YY or Y = Year WW or W = Work Week ORDERING INFORMATION Device Package Shipping MC14017BCP PDIP-16 2000/Box MC14017BD SOIC-16 48/Rail MC14017BDR2 SOIC-16 2500/Tape & Reel MC14017BF SOEIAJ-16 See Note 1. MC14017BFEL SOEIAJ-16 See Note 1. 1. For ordering information on the EIAJ version of the SOIC packages, please contact your local ON Semiconductor representative. Publication Order Number: MC14017B/D MC14017B PIN ASSIGNMENT Q5 1 16 VDD Q1 2 15 RESET Q0 3 14 CLOCK Q2 4 13 CE Q6 5 12 Cout Q7 6 11 Q9 Q3 7 10 Q4 VSS 8 9 Q8 FUNCTIONAL TRUTH TABLE (Positive Logic) Clock Clock Enable 0 X X X 1 X 0 X X 1 BLOCK DIAGRAM Reset Decode Output=n 0 0 1 0 0 0 0 n n Q0 n+1 n n n+1 CLOCK 14 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q9 Cout CLOCK 13 ENABLE RESET 15 X = Don't Care. If n < 5 Carry = "1", Otherwise = "0". 3 2 4 7 10 1 5 6 9 11 12 VDD = PIN 16 VSS = PIN 8 LOGIC DIAGRAM Q5 Q1 1 2 C Q C D Q R R C Q C D Q R R Q7 6 Q3 7 Q9 11 14 CLOCK CLOCK ENABLE RESET 12 13 15 3 C Q C D Q R R 5 Q0 4 Q6 Q2 http://onsemi.com 2 C Q C D Q R R C Q C D Q R R 9 10 Q3 Q4 CARRY MC14017B IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIII IIII III IIIII IIIIIIIII IIIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIII IIII III III III IIII III IIII III III III IIIII IIIIIIIII IIIII IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIIIIIIIIII IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIII IIII III IIIIIIIIIIIIIIIII III IIIIIIIIII IIII III IIIIIIIIIIIIIIIII III IIIIIIIIII IIII III IIIIIIIIIIIIIIIII III IIIIIIIIII IIII III IIIIIIIIIIIIIIIII III ELECTRICAL CHARACTERISTICS (Voltages Referenced to VSS) Characteristic Output Voltage Vin = VDD or 0 Symbol - 55_C 25_C 125_C VDD Vdc Min Max Min Typ (4.) Max Min Max Unit "0" Level VOL 5.0 10 15 -- -- -- 0.05 0.05 0.05 -- -- -- 0 0 0 0.05 0.05 0.05 -- -- -- 0.05 0.05 0.05 Vdc "1" Level VOH 5.0 10 15 4.95 9.95 14.95 -- -- -- 4.95 9.95 14.95 5.0 10 15 -- -- -- 4.95 9.95 14.95 -- -- -- Vdc Input Voltage "0" Level (VO = 4.5 or 0.5 Vdc) (VO = 9.0 or 1.0 Vdc) (VO = 13.5 or 1.5 Vdc) VIL 5.0 10 15 -- -- -- 1.5 3.0 4.0 -- -- -- 2.25 4.50 6.75 1.5 3.0 4.0 -- -- -- 1.5 3.0 4.0 "1" Level VIH 5.0 10 15 3.5 7.0 11 -- -- -- 3.5 7.0 11 2.75 5.50 8.25 -- -- -- 3.5 7.0 11 -- -- -- 5.0 5.0 10 15 - 3.0 - 0.64 - 1.6 - 4.2 -- -- -- -- - 2.4 - 0.51 - 1.3 - 3.4 - 4.2 - 0.88 - 2.25 - 8.8 -- -- -- -- - 1.7 - 0.36 - 0.9 - 2.4 -- -- -- -- IOL 5.0 10 15 0.64 1.6 4.2 -- -- -- 0.51 1.3 3.4 0.88 2.25 8.8 -- -- -- 0.36 0.9 2.4 -- -- -- mAdc Input Current Iin 15 -- 0.1 -- 0.00001 0.1 -- 1.0 Adc Input Capacitance (Vin = 0) Cin -- -- -- -- 5.0 7.5 -- -- pF Quiescent Current (Per Package) IDD 5.0 10 15 -- -- -- 5.0 10 20 -- -- -- 0.005 0.010 0.015 5.0 10 20 -- -- -- 150 300 600 Adc IT 5.0 10 15 Vin = 0 or VDD (VO = 0.5 or 4.5 Vdc) (VO = 1.0 or 9.0 Vdc) (VO = 1.5 or 13.5 Vdc) Output Drive Current (VOH = 2.5 Vdc) (VOH = 4.6 Vdc) (VOH = 9.5 Vdc) (VOH = 13.5 Vdc) (VOL = 0.4 Vdc) (VOL = 0.5 Vdc) (VOL = 1.5 Vdc) Vdc Vdc IOH Source Sink Total Supply Current (5.) (6.) (Dynamic plus Quiescent, Per Package) (CL = 50 pF on all outputs, all buffers switching) mAdc IT = (0.27 A/kHz) f + IDD IT = (0.55 A/kHz) f + IDD IT = (0.83 A/kHz) f + IDD 4. Data labelled "Typ" is not to be used for design purposes but is intended as an indication of the IC's potential performance. 5. The formulas given are for the typical characteristics only at 25_C. 6. To calculate total supply current at loads other than 50 pF: IT(CL) = IT(50 pF) + (CL - 50) Vfk where: IT is in A (per package), CL in pF, V = (VDD - VSS) in volts, f in kHz is input frequency, and k = 0.0011. http://onsemi.com 3 Adc MC14017B IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIII IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIIIIIIIII III IIIIIIIIIIIIIII IIIII IIII IIIIIIIIII III IIII IIII IIII IIIIIIIIIIIIIII IIIII IIII IIIIIIIIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III SWITCHING CHARACTERISTICS (7.) (CL = 50 pF, TA = 25_C) Characteristic Symbol Output Rise and Fall Time tTLH, tTHL = (1.5 ns/pF) CL + 25 ns tTLH, tTHL = (0.75 ns/pF) CL + 12.5 ns tTLH, tTHL = (0.55 ns/pF) CL + 9.5 ns tTLH, tTHL Propagation Delay Time Reset to Decode Output tPLH, tPHL = (1.7 ns/pF) CL + 415 ns tPLH, tPHL = (0.66 ns/PF) CL + 197 ns tPLH, tPHL = (0.5 ns/pF) CL + 150 ns tPLH, tPHL Propagation Delay Time Clock to Cout tPLH, tPHL = (1.7 ns/pF) CL + 315 ns tPLH, tPHL = (0.66 ns/pF) CL + 142 ns tPLH, tPHL = (0.5 ns/pF) CL + 100 ns tPLH, tPHL Propagation Delay Time Clock to Decode Output tPLH, tPHL = (1.7 ns/pF) CL + 415 ns tPLH, tPHL = (0.66 ns/pF) CL + 197 ns tPLH, tPHL = (0.5 ns/pF) CL + 150 ns tPLH, tPHL Turn-Off Delay Time Reset to Cout tPLH = (1.7 ns/pF) CL + 315 ns tPLH = (0.66 ns/pF) CL + 142 ns tPLH = (0.5 ns/pF) CL + 100 ns tPLH Clock Pulse Width VDD Vdc Min Typ (8.) Max 5.0 10 15 -- -- -- 100 50 40 200 100 80 Unit ns ns 5.0 10 15 -- -- -- 500 230 175 1000 460 350 ns 5.0 10 15 -- -- -- 400 175 125 800 350 250 ns 5.0 10 15 -- -- -- 500 230 175 1000 460 350 ns 5.0 10 15 -- -- -- 400 175 125 800 350 250 tw(H) 5.0 10 15 250 100 75 125 50 35 -- -- -- ns fcl 5.0 10 15 -- -- -- 5.0 12 16 2.0 5.0 6.7 MHz Reset Pulse Width tw(H) 5.0 10 15 500 250 190 250 125 95 -- -- -- ns Reset Removal Time trem 5.0 10 15 750 275 210 375 135 105 -- -- -- ns Clock Input Rise and Fall Time tTLH, tTHL 5.0 10 15 Clock Enable Setup Time tsu 5.0 10 15 350 150 115 175 75 52 -- -- -- ns Clock Enable Removal Time trem 5.0 10 15 420 200 140 260 100 70 -- -- -- ns Clock Frequency -- No Limit 7. The formulas given are for the typical characteristics only at 25_C. 8. Data labelled "Typ" is not to be used for design purposes but is intended as an indication of the IC's potential performance. http://onsemi.com 4 MC14017B VDD VSS VDD VSS A B S1 S1 Vout CLOCK Q0 ENABLE Q1 Q2 Q3 Q4 RESET Q5 Q6 Q7 Q8 Q9 CLOCK Cout Output Sink Drive Output Source Drive Decode Outputs (S1 to A) Clock to desired outputs (S1 to B) Carry Clock to 5 thru 9 (S1 to B) S1 to A VGS = VDD - VDD VDS = Vout Vout - VDD ID EXTERNAL POWER SUPPLY VSS Figure 1. Typical Output Source and Output Sink Characteristics Test Circuit VDD 500 F 0.01 F CERAMIC ID Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q9 Cout CLOCK ENABLE RESET PULSE GENERATOR fc CLOCK VSS CL CL CL CL CL Figure 2. Typical Power Dissipation Test Circuit http://onsemi.com 5 CL CL CL CL CL CL MC14017B APPLICATIONS INFORMATION Figure 3 shows a technique for extending the number of decoded output states for the MC14017B. Decoded outputs are sequential within each stage and from stage to stage, with no dead time (except propagation delay). RESET CLOCK CE MC14017B RESET CLOCK CE MC14017B Q0 Q1 * * * Q8 Q9 Q0Q1 * * * Q8 Q9 9 DECODED OUTPUTS RESET CLOCK CE MC14017B Q1 * * * Q8 Q9 8 DECODED OUTPUTS 8 DECODED OUTPUTS CLOCK FIRST STAGE INTERMEDIATE STAGES LAST STAGE Figure 3. Counter Expansion Pcp Ncp 90% CLOCK 50% trem CLOCK ENABLE trem RESET 20 ns Q0 Q2 Q3 Q4 20 ns 20 ns VDD 20 ns 20 ns 20 ns tPLH tPHL tTLH tPHL 90% 10% tPLH VDD VSS tPLH tPHL tPLH tTLH tPHL tTHL tTLH VOH VOL tTHL VOH 50% tPLH tPHL tTLH tPHL tPLH tPLH tTHL VOL tTHL VOH VOL tTHL tTLH tPHL tTLH tPHL 90% 10% tTHL VOH VOL Q7 tTHL Q8 VOH VOL tPLH tTLH tTHL tPLH tPHL Q9 Cout VOH VOL VOH VOL tTHL tPHL tPLH VOH VOL VOH VOL 50% Q5 Q6 VDD VSS VSS tPLH Q1 tsu 10% tTLH tPHL tPLH tTHL tPHL tTLH Figure 4. AC Measurement Definition and Functional Waveforms http://onsemi.com 6 tTHL VOH VOL VOH VOL MC14017B PACKAGE DIMENSIONS PDIP-16 P SUFFIX PLASTIC DIP PACKAGE CASE 648-08 ISSUE R -A- 16 9 1 8 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. B F C DIM A B C D F G H J K L M S L S -T- SEATING PLANE K H G D M J 16 PL 0.25 (0.010) M T A M 16 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 9 -B- 1 P 8 PL 0.25 (0.010) 8 M B S G R K F X 45 _ C SEATING PLANE J M D 16 PL 0.25 (0.010) MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0_ 10 _ 0.51 1.01 SOIC-16 D SUFFIX PLASTIC SOIC PACKAGE CASE 751B-05 ISSUE J -A- -T- INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0_ 10 _ 0.020 0.040 M T B S A S http://onsemi.com 7 DIM A B C D F G J K M P R MILLIMETERS MIN MAX 9.80 10.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.386 0.393 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.229 0.244 0.010 0.019 MC14017B PACKAGE DIMENSIONS SOEIAJ-16 F SUFFIX PLASTIC EIAJ SOIC PACKAGE CASE 966-01 ISSUE O 16 LE 9 Q1 M_ E HE 1 L 8 DETAIL P Z D e VIEW P A A1 b 0.13 (0.005) c M 0.10 (0.004) NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5. THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). DIM A A1 b c D E e HE L LE M Q1 Z MILLIMETERS MIN MAX --- 2.05 0.05 0.20 0.35 0.50 0.18 0.27 9.90 10.50 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 10 _ 0_ 0.70 0.90 --- 0.78 INCHES MIN MAX --- 0.081 0.002 0.008 0.014 0.020 0.007 0.011 0.390 0.413 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 10 _ 0_ 0.028 0.035 --- 0.031 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION NORTH AMERICA Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com Fax Response Line: 303-675-2167 or 800-344-3810 Toll Free USA/Canada N. American Technical Support: 800-282-9855 Toll Free USA/Canada EUROPE: LDC for ON Semiconductor - European Support German Phone: (+1) 303-308-7140 (M-F 1:00pm to 5:00pm Munich Time) Email: ONlit-german@hibbertco.com French Phone: (+1) 303-308-7141 (M-F 1:00pm to 5:00pm Toulouse Time) Email: ONlit-french@hibbertco.com English Phone: (+1) 303-308-7142 (M-F 12:00pm to 5:00pm UK Time) Email: ONlit@hibbertco.com EUROPEAN TOLL-FREE ACCESS*: 00-800-4422-3781 *Available from Germany, France, Italy, England, Ireland CENTRAL/SOUTH AMERICA: Spanish Phone: 303-308-7143 (Mon-Fri 8:00am to 5:00pm MST) Email: ONlit-spanish@hibbertco.com ASIA/PACIFIC: LDC for ON Semiconductor - Asia Support Phone: 303-675-2121 (Tue-Fri 9:00am to 1:00pm, Hong Kong Time) Toll Free from Hong Kong & Singapore: 001-800-4422-3781 Email: ONlit-asia@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-8549 Phone: 81-3-5740-2745 Email: r14525@onsemi.com ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. http://onsemi.com 8 MC14017B/D