INDUCTORS
MHQ1005P 1005 [0402 inch]*
* Dimensions Code JIS[EIA]
October 2013
Inductors for High Frequency Circuits
Multilayer Ceramic
MHQ-Pseries (For automobiles)
(2/10)
INDUCTORS
001-01 / 20131001 / inductor_automotive_high-frequency_mhq_en.fm
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
REMINDERS
(3/10)
INDUCTORS
001-01 / 20131001 / inductor_automotive_high-frequency_mhq_en.fm
• All specifications are subject to change without notice.
Inductors for High Frequency Circuits
Multilayer Ceramic
FEATURES
Unique ceramic material and configuration allows for the realization of high Q characteristics that are equivalent to that of air core wound
inductors.
Multilayer method allows for a lineup with fine increments of inductance.
APPLICATION
Automotive equipment, smart phones, tablet terminals, high frequency modules (PAs, VCOs, FEMs , etc.), Bluetooth, W-LAN, UWB, tuners
and other high frequency circuits for the mobile communication industry
PART NUMBER CONSTRUCTION
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
The Storage temperature range is for after the circuit board is mounted.
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
AEC-Q200
Overview of the MHQ-P Series
MHQ 1005 P 1N0 B T □□□
Series name L×W×H Dimensions Characteristics Inductance Inductance
tolerance Packaging style Internal code
(mm) (nH)
1005 1.0×0.5×0.5 P 1N1 1.1 B ±0.1nH T Taping
11N 11 C ±0.2nH
S ±0.3nH
G±2%
H±3%
J±5%
Ty p e
Temperature range
Package quantity Individual weight
Operating
temperature
Storage
temperature
（°C） （°C）(pieces/reel) （mg）
MHQ1005P –55 to +125 –55 to +125 10000 1
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
(4/10)
INDUCTORS
001-01 / 20131001 / inductor_automotive_high-frequency_mhq_en.fm
• All specifications are subject to change without notice.
Overview of the MHQ-P Series
RECOMMENDED REFLOW PROFILE
Preheating Soldering Peak
Temp. Time Temp. Time Temp. Time
T1 T2 t1 T3 t2 T4 t3
150°C 180°C 60 to 120s 230°C 30 to 60s 250 to 260°C 10s max.
Natural
cooling
t3
t1
Preheating
t2
Soldering
T3 T3
T4
T2
T1
t: Time
Peak
T: Temperature
(5/10)
INDUCTORS
001-01 / 20131001 / inductor_automotive_high-frequency_mhq_en.fm
• All specifications are subject to change without notice.
MHQ-Pseries
MHQ1005P Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
Dimensions in mm
0.22±0.080.22±0.08
1.00±0.05
0.12±0.05 0.12±0.05
0.60±0.050.50±0.10
Dimensions in mm
0.65
0.35 0.50 0.35
(6/10)
INDUCTORS
001-01 / 20131001 / inductor_automotive_high-frequency_mhq_en.fm
• All specifications are subject to change without notice.
MHQ-Pseries MHQ1005P Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
The " △" of the Part Number contains the inductance tolerance code, B（±0.1nH）, C（±0.2nH）, S（±0.3nH）, G（±2%）, H（±3%） or J（±5%）.
The " □□□ " of the Part Number contains the internal code.
・Short bar residual inductance =0.556nH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
LL measuring
frequency
(MHz)
Q
min.
Q measuring
frequency
(MHz)
Self-resonant
frequency
(GHz)
DC resistance
(:)
Rated current
(mA)
max.
Part No.*
(nH) Tolerance min. typ. max. typ.
1.0 ±0.1, ±0.2, 0.3nH 100 — 250 15.0 20.0 0.03 0.01 1200 MHQ1005P1N0△T□□□
1.1 ±0.1, ±0.2, 0.3nH 100 —250 14.0 20.0 0.03 0.02 1200 MHQ1005P1N1△T□□□
1.2 ±0.1, ±0.2, 0.3nH 100 — 250 13.0 18.3 0.03 0.01 1200 MHQ1005P1N2△T□□□
1.3 ±0.1, ±0.2, 0.3nH 100 —250 12.0 20.0 0.03 0.01 1200 MHQ1005P1N3△T□□□
1.5 ±0.1, ±0.2, 0.3nH 100 23 250 11.0 19.7 0.04 0.02 1000 MHQ1005P1N5△T□□□
1.6 ±0.1, ±0.2, 0.3nH 100 23 250 10.0 15.2 0.04 0.02 1000 MHQ1005P1N6△T□□□
1.8 ±0.1, ±0.2, 0.3nH 100 23 250 9.0 15.1 0.04 0.03 1000 MHQ1005P1N8△T□□□
2.0 ±0.1, ±0.2, 0.3nH 100 23 250 8.0 11.5 0.05 0.03 1000 MHQ1005P2N0△T□□□
2.2 ±0.1, ±0.2, 0.3nH 100 23 250 8.0 12.1 0.06 0.04 1000 MHQ1005P2N2△T□□□
2.4 ±0.1, ±0.2, 0.3nH 100 23 250 6.5 9.8 0.06 0.04 1000 MHQ1005P2N4△T□□□
2.7 ±0.1, ±0.2, 0.3nH 100 23 250 6.5 9.6 0.07 0.04 900 MHQ1005P2N7△T□□□
3.0 ±0.1, ±0.2, 0.3nH 100 23 250 6.0 9.4 0.08 0.06 900 MHQ1005P3N0△T□□□
3.3 ±0.1, ±0.2, 0.3nH 100 23 250 6.0 9.0 0.08 0.06 900 MHQ1005P3N3△T□□□
3.6 ±0.1, ±0.2, 0.3nH 100 23 250 5.5 8.4 0.09 0.07 900 MHQ1005P3N6△T□□□
3.9 ±0.1, ±0.2, 0.3nH 100 23 250 5.0 7.7 0.09 0.07 900 MHQ1005P3N9△T□□□
4.3 ±0.1, ±0.2, 0.3nH 100 23 250 5.0 7.1 0.10 0.08 800 MHQ1005P4N3△T□□□
4.7 ±0.1, ±0.2, 0.3nH 100 23 250 5.0 7.7 0.11 0.08 800 MHQ1005P4N7△T□□□
5.1 ±0.1, ±0.2, 0.3nH 100 23 250 4.5 7.2 0.12 0.09 800 MHQ1005P5N1△T□□□
5.6 ±0.1, ±0.2, 0.3nH 100 23 250 4.5 6.5 0.13 0.10 800 MHQ1005P5N6△T□□□
6.2 ±0.1, ±0.2, 0.3nH 100 23 250 4.0 5.9 0.13 0.09 700 MHQ1005P6N2△T□□□
6.8 ±2%, ±3%, ±5% 100 23 250 4.0 5.8 0.14 0.10 700 MHQ1005P6N8△T□□□
7.5 ±2%, ±3%, ±5% 100 23 250 4.0 5.6 0.16 0.12 600 MHQ1005P7N5△T□□□
8.2 ±2%, ±3%, ±5% 100 23 250 3.6 4.9 0.16 0.12 550 MHQ1005P8N2△T□□□
9.1 ±2%, ±3%, ±5% 100 23 250 3.4 4.5 0.17 0.13 550 MHQ1005P9N1△T□□□
10 ±2%, ±3%, ±5% 100 23 250 3.3 4.6 0.19 0.15 500 MHQ1005P10N△T□□□
12 ±2%, ±3%, ±5% 100 23 250 2.8 3.8 0.24 0.19 450 MHQ1005P12N△T□□□
15 ±2%, ±3%, ±5% 100 23 250 2.3 3.2 0.28 0.22 400 MHQ1005P15N△T□□□
Measurement item Product No. Manufacturer
L, Q 4291B+16193A Agilent Technologies
Self-resonant frequency 8720C Agilent Technologies
DC resistance Type-7561 Yokogawa
(7/10)
INDUCTORS
001-01 / 20131001 / inductor_automotive_high-frequency_mhq_en.fm
• All specifications are subject to change without notice.
MHQ-Pseries MHQ1005P Type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
The " △" of the Part Number contains the inductance tolerance code, B（±0.1nH）, C（±0.2nH）, S（±0.3nH）, G（±2%）, H（±3%） or J（±5%）.
The " □□□ " of the Part Number contains the internal code.
○Measurement equipment
＊ Equivalent measurement equipment may be used.
L(nH)typ. Q typ. Part No.*
500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz
1.0 1.0 1.0 1.0 1.0 56min. 76min. 126min. 130min. 160min. MHQ1005P1N0△T□□□
1.1 1.1 1.1 1.1 1.1 56min. 76min. 126min. 130min. 160min. MHQ1005P1N1△T□□□
1.2 1.2 1.2 1.2 1.2 56min. 76min. 126min. 130min. 160min. MHQ1005P1N2△T□□□
1.3 1.3 1.3 1.3 1.3 56min. 76min. 126min. 130min. 160min. MHQ1005P1N3△T□□□
1.5 1.5 1.5 1.5 1.5 56 76 126 130 160 MHQ1005P1N5△T□□□
1.6 1.6 1.6 1.6 1.6 60 78 136 144 174 MHQ1005P1N6△T□□□
1.8 1.8 1.8 1.8 1.8 52 72 123 129 152 MHQ1005P1N8△T□□□
2.0 2.0 2.0 2.0 2.0 54 70 108 113 132 MHQ1005P2N0△T□□□
2.2 2.1 2.2 2.2 2.2 47 62 104 110 129 MHQ1005P2N2△T□□□
2.3 2.3 2.4 2.4 2.4 45 59 98 102 120 MHQ1005P2N4△T□□□
2.6 2.6 2.7 2.7 2.7 45 57 87 91 108 MHQ1005P2N7△T□□□
2.9 2.9 3.0 3.0 3.1 47 59 92 97 116 MHQ1005P3N0△T□□□
3.2 3.2 3.3 3.3 3.4 41 55 91 95 112 MHQ1005P3N3△T□□□
3.5 3.5 3.6 3.6 3.7 41 53 87 91 107 MHQ1005P3N6△T□□□
3.8 3.8 3.9 4.0 4.1 40 53 87 91 105 MHQ1005P3N9△T□□□
4.2 4.2 4.4 4.5 4.6 41 54 86 89 102 MHQ1005P4N3△T□□□
4.6 4.6 4.7 4.8 4.9 38 50 82 85 98 MHQ1005P4N7△T□□□
5.0 5.0 5.2 5.3 5.4 41 52 79 83 97 MHQ1005P5N1△T□□□
5.5 5.5 5.7 5.8 6.1 39 51 81 84 95 MHQ1005P5N6△T□□□
6.1 6.1 6.5 6.7 7.0 45 56 84 87 99 MHQ1005P6N2△T□□□
6.7 6.7 7.2 7.4 7.8 42 53 77 80 91 MHQ1005P6N8△T□□□
7.3 7.3 7.9 8.1 8.5 38 49 76 79 87 MHQ1005P7N5△T□□□
8.0 8.1 8.9 9.2 9.8 42 53 77 80 88 MHQ1005P8N2△T□□□
8.9 9.0 9.9 10.3 11.2 38 49 73 75 79 MHQ1005P9N1△T□□□
9.8 9.9 11.1 11.6 12.6 39 51 74 75 77 MHQ1005P10N△T□□□
12 12 14 14 16 39 49 67 68 70 MHQ1005P12N△T□□□
15 15 18 20 23 37 45 57 57 54 MHQ1005P15N△T□□□
Product No. Manufacturer
4291B+16193A Agilent Technologies
(8/10)
INDUCTORS
001-01 / 20131001 / inductor_automotive_high-frequency_mhq_en.fm
• All specifications are subject to change without notice.
MHQ-Pseries MHQ1005P Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
○Measurement equipment
＊ Equivalent measurement equipment may be used.
10 100 1000 10000
0
1000
100
10
1
Frequency(MHz)
Inductance(nH)
15N
12N
10N
8N2
6N8
5N6
4N7
3N9
3N3
2N7
2N2
1N8
1N5
1N2
1N0
Product No. Manufacturer
E4991+16193A Agilent Technologies
(9/10)
INDUCTORS
001-01 / 20131001 / inductor_automotive_high-frequency_mhq_en.fm
• All specifications are subject to change without notice.
MHQ-Pseries MHQ1005P Type
ELECTRICAL CHARACTERISTICS
Q FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0
40
80
120
160
200
20
60
100
140
180
Q
10 100 1000 10000
Frequency(MHz)
15N
12N
10N
8N2
6N8
5N6
4N7
3N9
3N3
2N7
2N2
1N8
1N5
1N2
1N0
Product No. Manufacturer
E4991+16193A Agilent Technologies
(10/10)
INDUCTORS
001-01 / 20131001 / inductor_automotive_high-frequency_mhq_en.fm
• All specifications are subject to change without notice.
MHQ-Pseries
Packaging Style
REEL DIMENSIONS
TAPE DIMENSIONS
1.0
ø180±2.0
2.0±0.5
ø13±0.2
ø21±0.8
ø60min.
14.4max.
Dimensions in mm
8.4 +2.0
–0.0
8.0±0.3 3.5±0.05
1.75±0.1
4.0±0.1
1.5 +0.1
–0.0
Sprocket hole Cavity
A
KB
2.0±0.05 2.0±0.05
160min. Taping 200min.
300min.
Drawing direction
Typ e A B K
MHQ1005P 1.15±0.10 0.75±0.10 0.8 max.
