COINlight-OSTAR® - CO06A
Data Sheet
www.osram.com/LED-Systems
Picture for
Datasheet
is missing
!!!
Benefits
Powered by OSRAM OSTAR® - Lighting
38° optics for wide flood
Available in white, 3 colour temperatures
Low energy consumption
Applications
Downlight
Shop lighting
Orientation and accent lighting
Color Voltage
[V DC]* Power
[W]* Radiance
Angle [°]* Wavelength [nm]
Color Temp [K]* Lum. Intensity
[cd]*
Current
[A]*
Product Number
of LEDs
Technical O perating Data
white 24 12,0 38 5400 K 4500,5CO06A-W4-854 1
white 24 12,0 38 5400 K 3100,5CO06A-W3-854 1
white 24 12,0 38 4700 K 4500,5CO06A-W4-847 1
white 24 12,0 38 4700 K 3100,5CO06A-W3-847 1
white 24 12,0 38 3000 K 3300,5CO06A-W4-730 1
white 24 12,0 38 3000 K 2400,5CO06A-W3-730 1
All Data are related to the entire module
Due to the special condit ions of the manufa cturing processes of LED the typical data of technical parameters can only reflect statistical figures and do not necessarily
correspond to the actual parameters of each single product which could differ from the typical data.
Preliminary Data
*)
+)
Technical Features
Powered by one high perfomance OSRAM
OSTAR® - Lighti ng
Diameter of L ED module: Ø 50 mm
Dimension of COINlight-OSTAR® similar to
DECOSTAR®
38° viewing angle for wide flood
Operation only with OPTOTRONIC® power
supplies: OT20, OT20S, OT75, OT75E
Only parallel connection allowed
Parallel connection of up to 6 modules with the
power feed in the center to one OT75
Dimmable by pulse width modulation (PWM)
Cable length 500 mm, cable Ø 1.6 mm/AWG 22
Cable length 500 mm, cable Ø 0,2 mm²/AWG
24
Up to 60,000 h lifetime
Page 1 o f 4
CO06A - 25.01.2011
Drawings
Drawin
g
is missin
g
!!!
Operating Temperature
at Tc-Point [ °C ] * Stor age Temper a ture
[ °C ] *
Product Voltage Range
[ V dc ] * Reverse Voltage
[ V dc ] *
Minimum and Maximum Ratings
CO06A-W4-854 23 25 25...-30 105 -30 105... ...
CO06A-W3-854 23 25 25...-30 105 -30 105... ...
CO06A-W4-847 23 25 25...-30 105 -30 105... ...
CO06A-W3-847 23 25 25...-30 105 -30 105... ...
CO06A-W4-730 23 25 25...-30 105 -30 105... ...
CO06A-W3-730 23 25 25...-30 105 -30 105... ...
Exceeding maximum ratings for operati ng and storage temperature w i l l reduce ex pected life time or destroy the LED Module.
Exceeding maximum ratings for operating voltage will cause hazardous overload and will likely destroy the LED Module.
The temperature of the LED module must be measured at the Tc-point according to EN60598-1 in a thermally constant status with a temperature sensor or a temperature
sensitive label. For exact location of the Tc-point see drawing below.
*)
Page 2 o f 4
CO06A - 25.01.2011
Safety Information
The LED module itself and all its components must not be mechanically stressed.
Assembly must not damage or destroy conducting paths on the circuit board.
To avoid mechanical damage to the connecting cables, the module should be attached securely to the intended substrate. Heavy
vibration should be avoided.
Parallel connection is highly recommended as safe electrical operation mode.
Serial connection is not recommended. Unbalanced voltage drop can cause hazardous overload and damage the LED module.
Observe correct polarity!
Depending on the product incorrect polarity will lead to emission of red or no light. The module can be destroyed! Correct polarity
immediatelly! (see "reverse voltage", page 2)
Pay attention to standard ESD precautions when installing the module.
Please ensure that the power supply is of adequate power to operate the total load.
In case of thermal overload in the application COINlight-OSTAR® intelligent protection system would switch over into reversible blinki
mode. The LED module will not be damaged. Improving heat dissipation by extending the size of the heat sink or reducing the ambie
n
temperature would provide regular operation mode.
Electrical contact is achieved with the contact cables. One COINlight-OSTAR® can be operated on one OT20 or OT20S. A maximu
m
6 modules can be installed parallel on one OPTOTRONIC 75W. COINlight-OSTAR® cannot be operated with OT DALI 25/220-240/2
4
RGB as the intelligent protection system of the module is not supported.
COINlight-OSTAR® works as a three wire system: red cable (pluspole), black cable (minuspole) and a white cable for dimming.
A schematic drawing with wiring diagrams for dimming purpose is shown in the separate application note: "Dimming COINlight-
OSTAR®".
The module, as manufactured, has no conformal coating and therefore offers no inherent protection against corrosion.
Damage by corrosion will not be honored as a materials defect claim. It is the user's responsibility to provide suitable protection again
corrosive agents such as moisture and condensation and other harmful elements.
If the IP rating of the fixture should be higher than IP20, the design of the housing should be according to the IP standards in the
application.
To also ease the luminaire/installation approval, electronic control g ear for LED or LED modules should carry the CE mark and be EN
E
certified. In Europe the declarations of conformity must include the following standards:
CE: EC 61374-2-13, EN 55015, IEC 61547 and IEC 61000-3-2 - ENEC: 61374-2-13 and IEC/EN 62384.
Also check for the mark of an independent authorized certification institute.
Please see the relevant brochure for more detailed information (see "Related and Further Information")
Installation of LED modules (with power supplies) needs to be made with regard to all applicable electrical and safety standards. Onl
y
qualified personnel should be allowed to perform installations.
In order to drive OSRAM LED-Modules safely, it is absolutely necessary to operate them with an electronically stabilised powe
r
supply protecting against short circuits, overload and overheating.
OSRAM OPTOTRONIC® electronic control gear complies to all relevant standards and guarantees safe operation.
Page 3 o f 4
CO06A - 25.01.2011
Assembly Information
The mounting of the module has to be done on a metal heat sink!
In order to optimise the thermal management the metal surface needs to be clean (free from dirt and oil) and planar for the best cont
a
with the LED module.
The housing of the COINlight-OSTAR® is a primary heat sink. The metal surface increases the cooling effect, prolongs the service lif
e
time and increase luminous intensity.
Heat sink COHS-50 as accessory part available for optimized cooling of the module.
Productgroup Productname EAN * S-Unit *
Ordering Guide
COINlight-OSTAR® CO06A-W4-854 4008321231697 20
COINlight-OSTAR® CO06A-W3-854 4008321231451 20
COINlight-OSTAR® CO06A-W4-847 4008321231758 20
COINlight-OSTAR® CO06A-W3-847 4008321231512 20
COINlight-OSTAR® CO06A-W4-730 4008321231819 20
COINlight-OSTAR® CO06A-W3-730 4008321231574 20
EAN: Ordering number per single module
S-Unit: Modules per shipping unit
*)
Note: Typical performance data are subject to change without any further notice, particularly as LED technology evolves.
Related and Further Information
OPTOTRONIC® Data Sheets
http://catalog.myosram.com
The new dimension of light
153 S006 GB
www.osram.com/led-systems-downloads
OPTOTRONIC® Technical Guide
130 T0 0 8 GB www.os ram.com /ecg-downloa d s
Application Note: Dimming COINlight-OSTAR™
New standards for LED control gear
130 W011 GB
www.osram.com/ecg-download
Data sheet Heat sink COHS-50
www.osram.com/led-systems-downloads
Sales and Technical Support
Sales and technical support is given by the
local OSRAM subsidiaries.
On our world wide homepage all OSRAM
subsidiaries are listed with comp lete
address and phone numbers.
OSRAM GmbH
Hellabrunner Strasse 1
D - 81536 München
Germany
www.osram.com
+49 (0)89 6213-0
Page 4 o f 4
CO06A - 25.01.2011
Application note
Dimming COINlight-OSTAR
®
0.
Products
COINlight-OSTAR®
OT RGB DIM Without illustration
OTi DALI DIM
COT DIM
OT DMX RGB DIM
OT DMX 3x1 RGB DIM
BOT 60 EASY
AOT 75E/24
AOT 75/24
AOT 20S/24
AOT 20/24
Configuration
OSRAM OPTOTRONIC
POWER SUPPLY
OT RGB DIM Without illustration
OTi DALI DIM
COT DIM
OT DMX RGB DIM
OT DMX 3x1 RGB DIM
BOT 60 EASY
AOT 75E/24
AOT 75/24
AOT 20S/24
AOT 20/24
Configuration
OSRAM OPTOTRONIC
POWER SUPPLY
combination chart
COINlight-OSTAR® is a high end LED module, that can be
easily used in various combinations with OSRAM power
supplies and control systems.
Dimming COINlight-OSTAR® benefits:
- Wide dimming range from 0 – 100%
- Linear dimming characteristic
- No noise generation
1.
Operation with power supply (no dimming)
Page 2 of 2
Application note – Dimming COINlight-OSTAR
2.
Operation with OT EASY 60 (dimmable)
Use of COINlight-OSTAR® in basic light management systems with OT EASY 60 which consists
power supply and control in one device.
3.
Operation with OT DIM (dimmable)
Operation of COINlight-OSTAR® with a power supply in combination with 1-channel dimming
device.
