MC74AC132, MC74ACT132 Quad 2-Input NAND Schmitt Trigger The MC74AC/74ACT132 contains four 2-input NAND gates which are capable of transforming slowly changing input signals into sharply defined, jitter-free output signals. In addition, they have greater noise margin than conventional NAND gates. Each circuit contains a 2-input Schmitt trigger. The Schmitt trigger uses positive feedback to effectively speed-up slow input transitions, and provide different input threshold voltages for positive and negative-going transitions. This hysteresis between the positive-going and negative-going input threshold is determined by resistor ratios and is essentially insensitive to temperature and supply voltage variations. Features * * * * http://onsemi.com PDIP-14 N SUFFIX CASE 646 14 1 SOIC-14 D SUFFIX CASE 751A 14 1 Schmitt Trigger Inputs Outputs Source/Sink 24 mA ACT132 Has TTL Compatible Inputs Pb-Free Packages are Available 14 1 VCC 14 13 12 11 10 9 SOEIAJ-14 M SUFFIX CASE 965 8 ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 5 of this data sheet. 1 2 3 4 5 6 7 GND Figure 1. Pinout; 14-Lead Packages Conductors (Top View) FUNCTION TABLE Inputs Output A B Y L L H H L H L H H H H L H = HIGH Voltage Level L = LOW Voltage Level (c) Semiconductor Components Industries, LLC, 2006 October, 2006 - Rev. 7 1 Publication Order Number: MC74AC132/D MC74AC132, MC74ACT132 RECOMMENDED OPERATING CONDITIONS Symbol Parameter VCC Supply Voltage Vin, Vout DC Input Voltage, Output Voltage (Ref. to GND) tr, tf Input Rise and Fall Time (Note 1) AC Devices except Schmitt Inputs Min Typ Max Unit AC 2.0 5.0 6.0 ACT 4.5 5.0 5.5 0 - VCC VCC @ 3.0 V - 150 - VCC @ 4.5 V - 40 - VCC @ 5.5 V - 25 - VCC @ 4.5 V - 10 - VCC @ 5.5 V - 8.0 - - - 140 C -40 25 85 C V V ns/V tr, tf Input Rise and Fall Time (Note 2) ACT Devices except Schmitt Inputs TJ Junction Temperature (PDIP) TA Operating Ambient Temperature Range IOH Output Current - High - - -24 mA IOL Output Current - Low - - 24 mA ns/V 1. Vin from 30% to 70% VCC; see individual Data Sheets for devices that differ from the typical input rise and fall times. 2. Vin from 0.8 V to 2.0 V; see individual Data Sheets for devices that differ from the typical input rise and fall times. DC CHARACTERISTICS Symbol VOH VOL Parameter Minimum High Level Output Voltage Maximum Low Level Output Voltage IIN Maximum Input Leakage Current IOLD Minimum Dynamic Output Current IOHD ICC Maximum Quiescent Supply Current VCC (V) 74AC 74AC TA = +25C TA = -40C to +85C Typ Guaranteed Limits 3.0 4.5 5.5 2.99 4.49 5.49 2.9 4.4 5.4 2.9 4.4 5.4 3.0 4.5 5.5 - - - 2.56 3.86 4.86 2.46 3.76 4.76 3.0 4.5 5.5 0.002 0.001 0.001 0.1 0.1 0.1 0.1 0.1 0.1 3.0 4.5 5.5 - - - 0.36 0.36 0.36 0.44 0.44 0.44 5.5 - 0.1 5.5 - 5.5 - - 5.5 Unit V V IOUT = -50 mA *VIN = VIL or VIH -12 mA IOH -24 mA -24 mA IOUT = 50 mA V *VIN = VIL or VIH 12 mA IOL 24 mA 24 mA 1.0 mA VI = VCC, GND - 75 mA VOLD = 1.65 V Max - -75 mA VOHD = 3.85 V Min 4.0 40 mA VIN = VCC or GND *All outputs loaded; thresholds on input associated with output under test. Maximum test duration 2.0 ms, one output loaded at a time. NOTE: IIN and ICC @ 3.0 V are guaranteed to be less than or equal to the respective limit @ 5.5 V VCC. http://onsemi.com 2 V Conditions MC74AC132, MC74ACT132 AC CHARACTERISTICS (For Figures and Waveforms - See Section 3 of the ON Semiconductor FACT Data Book, DL138/D) Symbol VCC* (V) Parameter 74AC 74AC TA = +25C CL = 50 pF TA = -40C to +85C CL = 50 pF Min Typ Max Min Max Unit Fig. No. tPLH Propagation Delay 3.3 5.0 2.0 2.0 - - 13.0 9.0 1.5 1.5 14.0 10.0 ns 3-5 tPHL Propagation Delay 3.3 5.0 2.0 2.0 - - 13.5 9.0 1.5 1.5 15.0 10.0 ns 3-5 *Voltage Range 3.3 V is 3.3 V 0.3 V. Voltage Range 5.0 V is 5.0 V 0.5 V. DC CHARACTERISTICS Symbol VOH VOL Parameter Minimum High Level Output Voltage Maximum Low Level Output Voltage VCC (V) 74ACT 74ACT TA = +25C TA = -40C to +85C Unit Conditions Typ Guaranteed Limits 4.5 5.5 4.49 5.49 4.4 5.4 4.4 5.4 4.5 5.5 - - 3.86 4.86 3.76 4.76 4.5 5.5 0.001 0.001 0.1 0.1 0.1 0.1 4.5 5.5 - - 0.36 0.36 0.44 0.44 V *VIN = VIL or VIH 24 mA IOL 24 mA IOUT = -50 mA V *VIN = VIL or VIH -24 mA IOH -24 mA V IOUT = 50 mA V IIN Maximum Input Leakage Current 5.5 - 0.1 1.0 mA VI = VCC, GND DICCT Additional Max. ICC/Input 5.5 0.6 - 1.5 mA VI = VCC - 2.1 V IOLD Minimum Dynamic Output Current 5.5 - - 75 mA VOLD = 1.65 V Max 5.5 - - -75 mA VOHD = 3.85 V Min 5.5 - 4.0 40 mA VIN = VCC or GND IOHD ICC Maximum Quiescent Supply Current *All outputs loaded; thresholds on input associated with output under test. Maximum test duration 2.0 ms, one output loaded at a time. AC CHARACTERISTICS (For Figures and Waveforms - See Section 3 of the ON Semiconductor FACT Data Book, DL138/D) Symbol VCC* (V) Parameter 74ACT 74ACT TA = +25C CL = 50 pF TA = -40C to +85C CL = 50 pF Min Typ Max Min Max Unit Fig. No. tPLH Propagation Delay 5.0 3.0 - 11.5 2.5 13.0 ns 3-6 tPHL Propagation Delay 5.0 3.0 - 11.0 2.5 12.5 ns 3-5 *Voltage Range 5.0 V is 5.0 V 0.5 V. http://onsemi.com 3 MC74AC132, MC74ACT132 INPUT CHARACTERISTICS (unless otherwise specified) Symbol Parameter VCC (V) 74AC 74ACT Unit Test Conditions Vt + Maximum Positive Threshold 3.0 4.5 5.5 2.2 3.2 3.9 2.0 V TA = Worst Case Vt - Minimum Negative Threshold 3.0 4.5 5.5 0.5 0.9 1.1 0.8 V TA = Worst Case Vh(max) Maximum Hysteresis 3.0 4.5 5.5 1.2 1.4 1.6 1.2 V TA = Worst Case Vh(min) Minimum Hysteresis 3.0 4.5 5.5 0.3 0.4 0.5 0.4 V TA = Worst Case CAPACITANCE Symbol Parameter Value Typ Unit Test Conditions CIN Input Capacitance 4.5 pF VCC = 5.0 V CPD Power Dissipation Capacitance 30 pF VCC = 5.0 V http://onsemi.com 4 MC74AC132, MC74ACT132 MARKING DIAGRAMS PDIP-14 14 SOIC-14 14 14 MC74AC132N AWLYYWWG 1 14 74AC132 ALYWG AC132G AWLYWW 1 1 14 14 74ACT132 ALYWG ACT132G AWLYWW MC74ACT132N AWLYYWWG 1 SOEIAJ-14 1 1 A WL, L YY, Y WW, W G = Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Package ORDERING INFORMATION Device Package MC74AC132N PDIP-14 MC74AC132NG PDIP-14 (Pb-Free) MC74ACT132N PDIP-14 MC74ACT132NG PDIP-14 (Pb-Free) MC74AC132D SOIC-14 MC74AC132DG SOIC-14 (Pb-Free) MC74AC132DR2 SOIC-14 MC74AC132DR2G SOIC-14 (Pb-Free) MC74ACT132D SOIC-14 MC74ACT132DG SOIC-14 (Pb-Free) MC74ACT132DR2 SOIC-14 MC74ACT132DR2G SOIC-14 (Pb-Free) MC74AC132MEL SOEIAJ-14 MC74AC132MELG SOEIAJ-14 (Pb-Free) MC74ACT132MEL SOEIAJ-14 MC74ACT132MELG SOEIAJ-14 (Pb-Free) http://onsemi.com 5 Shipping 25 Units/Rail 55 Units/Rail 2500/Tape & Reel 55 Units/Rail 2500/Tape & Reel 2000/Tape & Reel MC74AC132, MC74ACT132 PACKAGE DIMENSIONS PDIP-14 CASE 646-06 ISSUE P 14 8 1 7 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. B A F L N C -T- SEATING PLANE H G D 14 PL J K 0.13 (0.005) M M http://onsemi.com 6 DIM A B C D F G H J K L M N INCHES MIN MAX 0.715 0.770 0.240 0.260 0.145 0.185 0.015 0.021 0.040 0.070 0.100 BSC 0.052 0.095 0.008 0.015 0.115 0.135 0.290 0.310 --- 10 _ 0.015 0.039 MILLIMETERS MIN MAX 18.16 19.56 6.10 6.60 3.69 4.69 0.38 0.53 1.02 1.78 2.54 BSC 1.32 2.41 0.20 0.38 2.92 3.43 7.37 7.87 --- 10 _ 0.38 1.01 MC74AC132, MC74ACT132 PACKAGE DIMENSIONS SOIC-14 CASE 751A-03 ISSUE H NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. -A- 14 8 -B- P 7 PL 0.25 (0.010) M 7 1 G -T- D 14 PL 0.25 (0.010) T B S A DIM A B C D F G J K M P R J M K M F R X 45 _ C SEATING PLANE B M S SOLDERING FOOTPRINT* 7X 7.04 14X 1.52 1 14X 0.58 1.27 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 7 MILLIMETERS MIN MAX 8.55 8.75 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.337 0.344 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.228 0.244 0.010 0.019 MC74AC132, MC74ACT132 PACKAGE DIMENSIONS SOEIAJ-14 CASE 965-01 ISSUE A 14 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5. THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). LE 8 Q1 E HE M_ L 7 1 DETAIL P Z D VIEW P A e A1 b 0.13 (0.005) c M 0.10 (0.004) DIM A A1 b c D E e HE 0.50 LE M Q1 Z MILLIMETERS MIN MAX --- 2.05 0.05 0.20 0.35 0.50 0.10 0.20 9.90 10.50 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 10 _ 0_ 0.70 0.90 --- 1.42 INCHES MIN MAX --- 0.081 0.002 0.008 0.014 0.020 0.004 0.008 0.390 0.413 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 10 _ 0_ 0.028 0.035 --- 0.056 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 8 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC74AC132/D