1mm Pitch Wire-to-Board Connectors supporting LVDS signal FX15 Series Space saving, Equal length transmission lines Termination side: 0.5mm pitch, 1-row construction Mating side: 1 mm pitch, staggered 2-row construction Fig.1 Features 1. Space-saving Self-alignment of 1.5mm Large guide post 1.5mm Reduction in space is achieved by designing the contacts in 2-row staggered 1mm pitch on the mating side and on a single row 0.5mm pitch on the termination side (Fig.1). 1.5mm 2. Equal length transmission lines Contact configuration provides equal length transmission lines, which prevents LVDS signal loss within the connector. 3. Variations Fig.2 Side latch -locks Availability of shielded and non-shielded types allows for design flexibility and cost reduction. 4. Self alignment and self-guiding Built-in guide posts allow secure self-alignment within 1.5mm (Fig.2). 5. Secure and complete mating / unmating Side latch locking provides complete and secure mating, as well as easy unmating (Fig.3). 6. Enhanced shielding performance with FX15S Enlarged metal shields prevent intrusion and emission of electromagnetic interference, which enhances the integrity of the LVDS signal (Fig.4). 7. RoHS compliant All materials and substances used to produce this product comply with RoHS standards. With metal shields (FX15 and FX15S Series) Without metal shields (FX15M Series) Fig.3 High Shielding Performance 0 Without metal Emitting Noise Level (dBm) Dec.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved. Contacts consolidated into 1 row for equal length transmission lines -10 With metal -20 -30 -40 -50 0.1 0.2 0.3 0.5 1 1.5 2 Frequency (GHz) In cases where the application will demand a high level of reliability, such as automotive, please contact a company representative for further information. 2015.10e 3 Fig.4 1 FX15 Series1mm Pitch Wire-to-Board Connectors supporting LVDS signal Product Specifications Current rating Voltage rating Dec.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved. Ratings 0.5A 100V AC Operating temperature range Storage temperature range -55c to +80c (Note 1) -10c to +60c (Note 2) Item 1. Contact resistance 2. Insulation resistance 3. Withstanding voltage 4. Insertion-Extraction force Specification 60mo max. (Note 3) 500Mo min. No flashover or insulation breakdown. 2N min., 30N max. Conditions 1mA 100V DC 300V AC/one minute With corresponding connector 5. Mating cycles Contact resistance : 80mo max.(Note 3) 50 cycles 6. Vibration resistance 7. Shock resistance No electrical discontinuity of 1s or more. No electrical discontinuity of 1s or more. Frequency: 10 to 55 Hz, single amplitude of 0.75mm, 2 hours, 3 axis Acceleration of 490m/s2, 11ms durations, sine half-wave waveform, 3 cycles, 3axis. 8. Humidity resistance Contact resistance : 80mo max. 96 hours at 40c, RH 90% to 95% No damage, cracks, or parts dislocation.(Note 3) 9. Temperature cycle Contact resistance : 80mo max. (Note 3) Insulation resistance : 500Mo min. Temperature : -55c +15c to +35c +85c +15c to +35c Time : 30 5 30 5 (Minutes) 5 cycles 10. Salt spray Contact resistance : 80mo max. (Note 3) No corrosions 5% water solution for 48 hours. Note 1 : Includes temperature rise caused by current flow. Note 2 : The term "storage" refers to products stored for long period of time prior to mounting and use. Operating temperature and humidity range includes non-conducting condition of installed connectors in storage, shipment or during transportation. Note 3 : Includes wire conductor resistance (12mm long). Materials / Finish Receptacle Insulator Component Material Polyamide Finish Color : Black Remarks UL94V-0 Contact Phosphor bronze Contact area : Gold plated Termination area : Tin plated --------------- FX15S : Nickel silver FX15SC : Stainless steel FX15S : --------------FX15SC : Tin plated --------------- Phosphor bronze Selective gold flash plated --------------- Insulator Material Polyamide Finish Color : Black Remarks UL94V-0 Contact Phosphor bronze Contact area : Gold plated Termination area : Tin plated --------------- Metal shell (shielded version only) Metal latch locks (shielded version only) Nickel silver Stainless steel ----------------------------- ----------------------------- Metal shell, metal latch locks (on micro coax version only) Stainless steel Nickel plated --------------- Metal shell (shielded version only) Metal fittings (shielded version only) Plug Component Product Number Structure qSeries Name wConfiguration Receptacle FX15 S - 31 S - 0.5 SH (**) q w e r t y Plug w e r u Crimp contact FX15 - 3032 PCF B q i o !0 P S : Male contact : Female contact tContact pitch : 0.5 mm SH yHousing configuration SV : Right angle : Straight uTermination C : Crimp 0.5SD : Micro-coaxial cable GND : Separate ground plate iApplicable conductor 2830 3032 : 28 to 30 AWG : 30 to 32 AWG oPackaging !0Plating (contact area) PCF B Blank (30) : Male contact / reel : Gold plated : Embossed Packaging (1,000 pcs/reel) : Embossed Packaging (100 pcs/reel) !1Packaging 2 15M : With shields (or crimp contact) : With shields - enhanced shielding : With shields - enhanced shielding (PCB mounting pattern : VESA standard) : Without shields eNumber of contacts rConnector type FX15 S - 31 P - C q !1 : FX15 Blank 15S 15SC FX15 Series1mm Pitch Wire-to-Board Connectors supporting LVDS signal FX15 Series - Functional Diagram Crimp contact Plugs Receptacles With shields-standard Vertical, with shields (FX15-31P-C) (FX15-31S-0.5SV) B Crimp contact (FX15-3032-PCFB) (FX15M-P-C) Right angle, with shields -enhanced shielding (FX15S-S-0.5SH) B With shields - enhanced shielding (FX15S-P-C) Right angle, without shields (FX15M-S-0.5SH) B Dec.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved. Without shields Crimp contact (FX15-2830-PCFB) With shields - enhanced shielding 28 to 30 AWG (FX15SW-31P-C) With shields - enhanced shielding PCB mouting pattern : VESA standard (FX15SC-S-0.5SH) 28 Ground plate (FX15S-P-GND) Micro-coaxial cable (FX15S-P-0.5SD) With shields - enhanced shielding PCB mouting pattern : VESA standard (FX15SC-S-0.5SV) A 3 FX15 Series1mm Pitch Wire-to-Board Connectors supporting LVDS signal Plugs With shields (FX15-31P-C) (27) 24.60.3 22.570.15 2.70.1 18.30.3 3.70.3 (13.45) 9.40.3 Polarizing mark indicator Dec.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved. No.2 Part No. HRS No. No. of contacts RoHS FX15-31P-C 575-2101-2 31 Yes Note 1 : Packaged in trays. Note 2 : Dimensions in parenthesis ( ) are reference dimensions. No.1 140.15 P=10.1 No.30 P=10.1 150.15 No.31 With shields, enhanced shielding (FX15S-**P-C) (A) B0.3 C0.15 40.3 2.70.1 (13.45) 9.40.3 Polarizing mark indicator 3.70.3 D0.3 No.2 No.1 No.n-1 P=10.1 F0.15 No.n Part No. HRS No. No. of contacts A B C D E F FX15S-31P-C 575-2106-6 31 27 24.6 22.6 18.3 14 15 FX15S-41P-C 575-2107-9 41 32 29.6 27.6 23.3 19 20 FX15S-51P-C 575-2103-8 51 37 34.6 32.6 28.3 24 25 Note 1: Packaged in trays. Note 2 : Dimensions in parenthesis ( ) are reference dimensions. 4 E0.15 P=10.1 RoHS Yes FX15 Series1mm Pitch Wire-to-Board Connectors supporting LVDS signal With shields - enhanced shielding 28 to 30 AWG (FX15SW-31P-C) (27) 24.60.3 22.570.15 Polarizing mark indicator 40.3 2.70.1 (13.45) 9.40.3 B 28 Part No. HRS No. No. of contacts RoHS FX15SW-31P-C 575-2113-1 31 Yes No.2 140.15 P=10.1 3.70.3 No.30 A Note 1 : Packaged in trays. Note 2 : Dimensions in parenthesis ( ) are reference dimensions. No.1 P=10.1 150.15 No.31 Without shields (FX15M-**P-C) (A) B0.3 Polarizing mark indicator (13.6) (13) 9.550.3 Dec.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved. 18.30.3 4.20.3 C0.3 (D) No.2 No.1 E0.15 P=10.1 No.n-1 P=10.1 F0.15 No.n Part No. HRS No. No. of contacts A B C D E F FX15M-21P-C 575-2109-4 21 24.8 20.5 13.7 25.8 9 10 FX15M-31P-C 575-2108-1 31 29.8 25.5 18.7 30.8 14 15 RoHS Yes Note 1 : Sold in 100 piece packages. Please order in full package quantities. Note 2 : Dimensions in parenthesis ( ) are reference dimensions. 5 FX15 Series1mm Pitch Wire-to-Board Connectors supporting LVDS signal BPlug crimp contacts Part No. HRS No. FX15-2830PCFB 575-2002-0 FX15-3032PCFB 575-2003-3 Packaging Quantity Finish RoHS Reel 20,000 pcs/reel Gold plated Yes Applicable cable (Tin plated, annealed copper wire) 30 AWG (7/0.1mm) 32 AWG (7/0.08mm) O0.5 to 0.6mm 1571 UL No. 1516, 1571 (Note) 1571 Wire strip length: 1.1 to 1.8mm Note : When using wires other than those noted above, please contact Hirose for asistance. Tools Item Applicator Press unit 6 Part No. AP105-FX15-2830 AP105-FX15-3032 CM-105C HRS No. 901-4036-0 901-4033-1 901-0001-0 0.350.1 Applicable crimp contact FX15-2830PCFB FX15-3032PCFB --------- (7) Jacket diameter 1517 0.720.1 0.90.15 Dec.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved. FX15-3032PCFB Applicable wire size (Stranded wire conductor) O0.56 to 0.72mm UL No. 20.15 28 AWG (7/0.127mm) 30 AWG (7/0.1mm) Jacket diameter 0.50.15 FX15-2830PCFB Applicable wire size (Stranded wire conductor) t=0.150.05 FX15 Series1mm Pitch Wire-to-Board Connectors supporting LVDS signal Cd#& Cd#c Plug - Micro-coaxial cable (FX15S-**P-0.5SD) Cd#' Cd#c"& 6 7%#( 8%#&* EdaVg^o^c\bVg ^cY^XVidg '#,%#&* &( -#,*%#( 6 Part No. HRS No. No. of contacts A B C D FX15S-41P-0.5SD 575-2110-3 41 31.9 29.6 27.57 20 FX15S-51P-0.5SD 575-2118-5 51 36.9 34.6 32.57 25 (#*%#( RoHS Yes Note 1 : Packaged in trays. Note 2 : Dimensions in parenthesis ( ) are reference dimensions. Ground plate for micro-coaxial cable type 6%#' &#**%#' 7%#' '#'%#' &&#)*%#( Part No. HRS No. No. of contacts A B FX15S-41P-GND 575-2111-6 41 29.2 30.06 FX15S-51P-GND 575-2117-2 51 34.2 35.06 RoHS Yes Note 1 : Packaged in trays. Note 2 : Dimensions in parenthesis ( ) are reference dimensions. Applicable cable (Micro-coaxial cable) 6%#' 7%#&* 40 AWG (7/0.03mm) No. of contacts 41 A 23.1 B 20 51 28.1 25 E2%#*%#%, >ccZgXdcYjXidg >chjaVidg <gdcY^c\WVg DjiZgXdcYjXidg ?VXZi (+id)%6L<B^Xgd"XdVm^VaXVWaZ %#+%#& %#%* "%#' 0.3mm to 0.5mm & 38 AWG (7/0.04mm) Jacket diameter HdaYZgXdVi & B>C % '#& "%#& Wire size (Standed wire inner conductor) 36 AWG (7/0.05mm) Cable preparation %#.B6M Dec.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved. Cd#& Cd#c E2%#*%#& 9%#&* 7 FX15 Series1mm Pitch Wire-to-Board Connectors supporting LVDS signal Receptacles 25.70.3 19.820.2 150.15 P=0.50.1 No.2 No.1 No.31 b (6) 5.60.3 40.3 a No.30 (0.8) Vertical, with shielding (FX15-31S-0.5SV) e f d 4.80.3 0.90.2 c Dec.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved. 1.50.2 10.2 10.2 1.50.2 0.80.1 22.80.3 Part No. HRS No. No. of contacts RoHS 31 Yes FX15-31S-0.5SV(**) 575-2201-7 ** [Specification Number : **, (**) ] Blank : Embossed packaging (1,000 pcs/reel) (30) : Embossed packaging (100 pcs/reel) BRecommended PCB mounting pattern and metal mask dimensions 22.80.05 0.30.03(Land) 0.250.03(Metal mask) 6.7 +0.1 0 3.2 +0.05 0 0 1.5 -0.05 P=0.50.03 0 2.2 -0.1 150.05 2-O1(TH) 2 0.2 +0.1 0 2-O1.4(LND) 0 0.9 -0.1 4.1+0.1 0 0 17.72 -0.1 21.92 +0.1 0 Note 1 : The co-planarity of the terminal leads is as follows: * All signals and shield leads "c" and "d": 0.1mm max. * Shield leads "a", "b", "e" and " f ": 0.15mm max. 2 : Area indicated by the crosshatched lines must be free of conductive traces or the conductive traces must be covered by resist film. 3 : Packaged on tape-and-reel. 4 : Dimensions in parenthesis ( ) are reference dimensions. 8 FX15 Series1mm Pitch Wire-to-Board Connectors supporting LVDS signal Right angle with shields - enhanced shielding (FX15S-**S-0.5SH) A0.2 0.50.1 0.20.05 4 No.n No.n-1 (4) 4 (3) Polarizing mark indicator 5 (2.6) (0.2) 4.450.1 (1.7) No.2 No.1 B0.2 C0.15 4.40.3 P=10.1 D0.15 E0.3 Part No. HRS No. No. of contacts A B C D E F G H FX15S-31S-0.5SH(**) 575-2306-5 ** 31 15 27.4 14 15 27.8 28.8 24.8 21.6 FX15S-41S-0.5SH(**) 575-2307-8 ** 41 20 32.4 19 20 32.8 33.8 29.8 26.6 FX15S-51S-0.5SH(**) 575-2303-7 ** 51 25 37.4 24 25 37.8 38.8 34.8 31.6 J K L M N P R S 18 15 ------ ------ 13.2 16.8 24.8 40 23 20 18.2 21.8 29.8 45 28 25 23.2 26.8 34.8 50 5.2 8.8 RoHS Yes BRecommended PCB mounting pattern and metal mask dimensions F +0.05 0 0 G -0.05 0 1.45 -0.05 0.50.03 0 1.7 -0.05 0 J -0.05 K0.05 0.30.03(Land) 0.250.03(Metal mask) 0 L -0.05 M +0.05 0 0 N23.2 -0.05 P26.8 +0.05 0 2.2 +0.05 0 3 13.85 4.25 3.7 +0.05 0 2 3.7 +0.05 0 4.15 3.55 +0.05 0 0 2.05 -0.05 H+0.05 0 2 Dec.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved. P=10.1 R 3 2 S Note 1 : The coplanarity of the terminal leads is 0.1mm max. for all signal leads and 0.15mm max. for the shield leads. 2 : Do not place any components in the area indicated. Placement of components in this area may affect mating and latch lock operation. 3 : Area indicated by the cross-hatched lines must be free of conductive traces or the conductive traces must be covered by resist film. 4 : The area marked indicates vacuum pick-and-place area for board placement with automatic equipment. 5 : Vacuum pick-up area 6 : Packaged on tape-and-reel. 7 : Dimensions in parenthesis ( ) are reference dimensions. 9 FX15 Series1mm Pitch Wire-to-Board Connectors supporting LVDS signal Right angle, without shielding (FX15M-**S-0.5SH) A0.2 0.50.1 0.20.05 No.n-1 No.n 6.150.3 No.2 No.1 Polarizing mark (5.5) indicator Vacuum pick and place area 4.80.3 4.30.3 B0.2 C0.15 P=10.1 Dec.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved. P=10.1 D0.15 6.550.3 [Specification Number : **, (**) ] Blank : Embossed packaging (1,000 pcs/reel) (30) : Embossed packaging (100 pcs/reel) Part No. HRS No. No. of contacts A B C D E F G FX15M-21S-0.5SH(**) 575-2309-3 ** 21 10 FX15M-31S-0.5SH(**) 575-2308-0 ** 31 15 22.4 9 10 17.9 10 35 27.4 14 15 22.9 15 40 RoHS Yes BRecommended PCB mounting pattern and metal mask dimensions E0.05 4 2 14 2 3.4+0.05 0 0.250.03(Metal mask) 0.90.03 0 1.9-0.05 P=0.50.03 0 3.7-0.05 7.4+0.05 0 (1.85) F0.05 0.30.03(Land) 2 G Note 1 : The co-planarity of all terminal leads is 0.1mm max. 2 : Do not place any components in the area indicated. Placement of components in this area may affect mating and latch lock operation. 3 : Packaged on tape-and-reel. 10 FX15 Series1mm Pitch Wire-to-Board Connectors supporting LVDS signal Right angle with shields - enhanced shielding (FX15SC-**S-0.5SH) A0.3 B0.2 C0.2 P=0.50.1 0.180.05 No.1 No.n 4.450.2 P=D0.1 0.50.1 Polarizing mark indicator (0.25 ) 1.50.1 3.10.2 1.50.1 (1.1) PCB mounting pattern : VESA standard E0.2 F0.3 G0.15 4.40.3 P=10.1 H0.15 [Specification Number : **, (**) ] Blank : Embossed packaging (1,000 pcs/reel) (30) : Embossed packaging (100 pcs/reel) Part No. HRS No. No. of contacts A B C D E F G H J K FX15SC-41S-0.5SH(**) 575-2310-2 ** 41 32.85 26 20 4 20 32.4 19 20 29.75 45 FX15SC-51S-0.5SH(**) 575-2311-5 ** 51 37.85 31 25 5 25 37.4 24 25 34.75 50 RoHS Yes BRecommended PCB mounting pattern and metal mask dimensions B0.05 No.1 No.n 2.050.05 12 6-1.30.05 E0.05 J0.05 2 2 1.550.05 3.50.05 P=D0.05 5.6 2.50.05 2 n-0.250.03 5.10.05 P=0.50.03 2.50.05 C0.05 1.550.05 Dec.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved. P=10.1 3 K Note 1 : The coplanarity of the terminal leads is 0.1mm max. 2 : Do not place any components in the area indicated. Placement of components in this area may affect mating and latch lock operation. 3 : Area indicated by the cross-hatched lines must be free of conductive traces or the conductive traces must be covered by resist film. 4 : Packaged on tape-and-reel. 5 : Dimensions in parenthesis ( ) are reference dimensions. 11 FX15 Series1mm Pitch Wire-to-Board Connectors supporting LVDS signal Vertical with shields - enhanced shielding (FX15SC-**S-0.5SV) PCB mounting pattern : VESA standard A0.2 No.1 No.n B0.2 0.180.05 P=0.50.1 1.50.1 P=C0.1 0.50.1 D0.2 E0.3 Dec.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved. 5.30.3 4.20.2 5.50.3 [Specification Number : **, (**) ] Blank : Embossed packaging (1,000 pcs/reel) (30) : Embossed packaging (100 pcs/reel) No. of contacts A B C D E FX15SC-41S-0.5SV(**) 575-2205-8 ** Part No. HRS No. 41 26 20 4 20 32.4 FX15SC-51S-0.5SV(**) 575-2204-5 ** 51 31 25 5 25 37.4 RoHS Yes BRecommended PCB layout and metal mask dimensions A0.05 No.n B0.05 P=0.50.3 n-0.250.03 2.50.05 2 1.550.05 3.50.05 1.550.05 No.1 P=C0.05 6-1.30.05 2.50.05 D0.05 A0.05 Note 1 : The coplanarity of the terminal leads is 0.1mm max. 2 : Area indicated by the cross-hatched lines must be free of conductive traces or the conductive traces must be covered by resist film. 3 : Packaged on tape-and-reel. 12 FX15 Series1mm Pitch Wire-to-Board Connectors supporting LVDS signal BPackaging Specifications Vertical, with shields Right angle, with shields-enhanced shielding (FX15-31S-0.5SV) (FX15S-**S-0.5SH) Unreeling direction Unreeling direction + 0 0 .1 .5 40.1 B0.1 C0.3 A0.1 A A (4.7) (0.5) O1 1.750.1 + 0 0 .1 5 120.1 20.250.1 40.450.1 440.3 Part No. A A A HRS No. No. of contacts D FX15-31S-0.5SV(**) 575-2201-7 ** 31 Part No. 44.5 Right angle, without shields HRS No. No. of contacts A FX15S-31S-0.5SH(**) 575-2306-5 ** 31 FX15S-41S-0.5SH(**) 575-2307-8 ** 41 FX15S-51S-0.5SH(**) 575-2303-7 ** 51 B C D 20.3 40.5 44 44.5 26.3 52.5 56 56.5 Reel dimensions (FX15M-**S-0.5SH) (D) 3 0.5 (1.6) O1 Unreeling direction (6.5) Part No. HRS No. No. of contacts A FX15M-21S-0.5SH(**) 575-2309-3 ** 21 FX15M-31S-0.5SH(**) 575-2308-0 ** 31 B C (O80) A0.1 B0.1 C0.3 (O380) 0 0 .1 (5.15) (0.5) .5 + 120.1 20.1 40.1 O1 Dec.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved. O1 . 5 120.1 20.15 40.1 O1 . + 0 0 .1 (6.7) (6.3) (4.8) (0.5) D 20.2 40.4 44 44.5 13 FX15 Series1mm Pitch Wire-to-Board Connectors supporting LVDS signal Right angle with shields - enhanced shielding Vertical with shields - enhanced shielding (FX15SC-**S-0.5SH) (FX15SC-**S-0.5SV) Unreeling direction + 0 0 .1 B0.1 C0.3 B0.1 C0.3 A0.1 Dec.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved. Part No. HRS No. No. of A contacts FX15SC-41S-0.5SH(**) 575-2310-2 ** 41 FX15SC-51S-0.5SH(**) 575-2311-5 ** 51 B C D RoHS Part No. 26.2 52.4 56 56.5 Yes 0.5 3 (O80) (O380) No. of A contacts 41 FX15SC-51S-0.5SV(**) 575-2204-5 ** 51 (1.6) O1 HRS No. FX15SC-41S-0.5SV(**) 575-2205-8 ** Reel dimensions 14 (7) (0.5) .5 40.1 A0.1 120.1 20.1 O1 (6.7) (0.5) 5 40.1 O1 . 120.1 20.1 +0 0 .1 Unreeling direction (D) B C D RoHS 26.2 52.4 56 56.5 Yes FX15 Series1mm Pitch Wire-to-Board Connectors supporting LVDS signal BRecommended temperature profile 250 230 230c 180c Te mp e r a t u r e ( c ) Dec.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved. 180 150 HRS test conditions Test board Glass epoxy 40mm30mm1mm thick Solder method : Reflow Solder composition : Paste 96.5%Sn/3%Ag/0.5%Cu Metal mask : 0.12mm thick Reflow cycles : 2 cycles MAX 250c 150c 100 25 0 9030sec. 3010sec. Preheating(150 to 180c) Sodering (230cmin) The temperature profile is based on the above conditions. In individual applications the actual temperature may vary, depending on solder paste type, volume/ Time (sec.) thickness and board size/thickness. Consult your solder paste and equipment manufacturer for specific recommendations. Note : The temperature profile indicates the maximum temperature of the connector surfaces at the highest point from the PCB mounting surface. BWashing Conditions Organic Solvent Washing Solvent type IPA (Isoporopyl alcohol) Room temperature washing Yes Heated washing Yes Water Type Washing When using water type cleaning agents (e.g., terpene, and alkali saponifiers), select the cleaning agent based on the documentation issued by the various manufacturers of cleaning agents which describes the effects on metals and resins. Be careful that parts are not left with moisture remaining on them. Washing Precautions Residual flux or cleaning agent on the contacts when washing with organic solvents or water type cleaners can give rise to the deterioration of electrical performance. In this regard it is important to check whether a thorough washing has been performed. 15 FX15 Series1mm Pitch Wire-to-Board Connectors supporting LVDS signal Precautions and recommendations Wire termination The following documents will be needed in order to perform the cable terminations. 1Basic cable termination and crimp requirements (general explanations). 2Contact crimp termination machine instruction manual (Explanation of the press) 3Applicator parts installation table (Applicator installation explanation) 4Crimp conditions table (Crimp height/Tensile strength standard values) 5Crimp quality fundamentals manual (Bell-mouth dimensions, bent up, bent down, rolling, etc.) * Correct cable preparation and crimp termination is based on understanding and following the procedures in the above documents. Dec.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved. Insertion of the crimp contacts in the housing Crimp contacts are inserted in the housing as illustrated below. Exercising caution when inserting, align the retention tab of the contact with the corresponding molded-in lance in the housing's contact cavity and push the contacts in. Make sure that the contact is fully inserted and the retention tab clears the molded-in lance. Molded-in lance Molded-in lance Retention tab facing up Molded-in lance Retention tab facing down Retention tab Crimp side Verify that the retention tabs clear the molded-in lances as shown on the illustration below. Retention tab Light pull on the wire, with force NOT EXCEEDING 3N will also verify the correct contact insertion. Removal of the contacts Using sharp-pointed tool of appropriate size gently lift the molded-in tab and pull-out the terminated contacts. Excersize caution as NOT to damage the molded-in lance. Should the damage occur, the entire housing will need to be replaced. 1 2 16 FX15 Series1mm Pitch Wire-to-Board Connectors supporting LVDS signal Precautions and recommendations [ Soldering precautions related to FX15S-**P-C connectors ] Grounding Methods of the ground wire or shields for the cable assemblies 1Solder the ground wire or the shields ONLY in the areas specifically designated for this purpose, as shown on the illustrations below. 2Observe the soldering iron tip temperature and soldering time specified. 3Do not apply excessive force to the connector by pressing it with the tip of a soldering iron. 4Do not splatter the flux from the solder core. Dec.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved. Soldering area 2 Soldering area 1 B B (Ground harness examples) 17 FX15 Series1mm Pitch Wire-to-Board Connectors supporting LVDS signal Precautions and recommendations Plug - micro-coaxial cable Cautions for soldering 1. For the micro coaxial cable assembled to this connector, cable alignment process as shown in "Recommended cable" on the page 1 is required before assembly. 1Width of ground bar shall be 1.05mm Max. including misalignment of overlapping, flush by cutting, side drop or soldering. Using an inadequate cable will interfere the assembly to the connector. Forceful assembly and soldering could cause mis-soldering and damage the product. 2Minimize the length of outer conductor beyond the ground the bar. 4Pre-solder and coat the inner conductor at the cable end. e q w Grounding bar w Dec.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved. 3Length of cutting the extra cable should be 2.1mm Max. Any longer cable may cause contact with the connector during assembly and could damage the product. Recommended minimum length is 2.0mm, but this can be altered as long as good soldering ability is maintained. Inner conductor rSolder coating Outer conductor 2. Recommended solder for the assembly is flux cored solder with 0.2mm dia. (Lead-free: Sn-3Ag-0.5Cu), 21mm length. If additional flux is used, make sure to prevent wicking onto the contact area. Wicking onto the contact area will cause the contacts to fail. 3. Before soldering the cable and connector with a cable assembly machine, check the points to avoid below. 1Misalinment of cable end to the terminals in pitch direction 2Excessive floating of cable end 4. Follow the recommended temperature profile shown below for the soldering. qMisalignment in pitch direction wfloating The optimum conditions for soldering can vary depending on cable type and length, and solder type. Be sure to check the recommended temperate profile and adjust the conditions accordingly. Heating 265c Solder tip pressurization 13~17N 250c Pre-heating 220c Heating Temperature 2655c Duration 3~4 sec Idling 50c 2s 1s 2s 3-4s Duration of pressure application 18 FX15 Series1mm Pitch Wire-to-Board Connectors supporting LVDS signal Precautions and recommendations 5. After soldering, check that no defect is found at soldered area. Examples of correct soldered and defective soldered state are shown below. Solder shortage A solder bridge A B BB B Floating Correct soldering [ Coutions for potting process ] 1. Protect the soldered area by UV cured resin (referred as "potting" hereafter), in order to prevent cable breakage during cabling and other issues. 2. Apply 3033 manufactured by THREEBOND CO., LTD. or any equivalent product for potting. Follow the instruction of the potting manufacturer for UV curing exposure. 3. Refer to the following conditions the potting area. Number of contacts A 41 23.7 51 28.7 0 1.25 -0.75 A -30 A 0 2.15 -0.4 Dec.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved. AA Enlarged view 4. Use extreme care in handling the soldered and potted assembly. Too much stress applied to the cable could break it. 19 FX15 Series1mm Pitch Wire-to-Board Connectors supporting LVDS signal Precautions and recommendations [ Coutions for ground plate assembly ] 1. Attach a ground plate separately provided as FX15S-41P-GND after the cable assembly process. 2. Place the ground plate onto the connector horizontally and pinch the two components from top and bottom with your fingers. Pinch from top and bottom with fingers Dec.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved. Ground plate (FX15S-41P-GND) A A wHorizontally from the top qAssembly ePinch with fingers 3. Check the six fitting points after assembly and make sure that they are all correctly fitted together. How to check fitting points (Cut section of fitting points) Fitting Fitting A Fitting Fitting Fitting Ground plate hooks the protrusion of connector housing Ground plate does not hook the protrusion of connector housing Fitting OK NG [ Soldering to ground plate ] 1. Solder down the metal bar of the cable and ground plate after the assembly of the ground plate to enhance grounding capability and to protect against vertical cable puling forces. Soldering Soldering A 20 FX15 Series1mm Pitch Wire-to-Board Connectors supporting LVDS signal Precautions and recommendations Packaging of the complete cable assemblies Exercise caution as not to tangle, twist or deform the complete cable assemblies when packaging. Special care should be taken NOT to apply any excessive stress to the individual wires. When removing the cable assemblies from the packaging do not pull on the wires. Make sure that the latch-locks are not interfering with packaging. Dec.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved. Packaging Connectors Mating of the connectors These connectors have a built in polarizing feature and will NOT mate when reversed. Do NOT try and force tem together. Align the connectors as shown on the illustration below and fully insert the plug into the receptacle. Confirm that both latchlocks are fully engaged. Triangle mark Triangle mark Arrow mark Mating Center mark Mating Center mark Additionally, this connector is equipped with reverse-insertion preventing mechanism, but a forced mating with a minimum force of 25N could damage the connector. Avoid any inappropriate mating, and perform the mating operation after checking the above-mentioned polarity indication. Treatment after mating has been completed After mating, please take care to prevent any stress or load on the connector during the routing of cables. If a load of a minimum of 5N is applied on the cable, the cable (crimp contact) could come off. Further, if the entire cable is pulled with a minimum force of 20N, the connector could be broken. Please take extra care not to pull the cable and cause cable disconnection. If you use a small gauge coaxial plug, a repeated rotation could also cause cable disconnection. Do not use the cable by rotating it repeatedly. The rotation times should be limited to a maximum of 10 even if rotation is required for routing. If your use requires folding back of the cable over the base of the connector, make sure to maintain a large turn-back radius away from the connector base. Take a large radius Keep the turn-back position away from the root of the connector. Pulling in the horizontal direction: Not acceptable Pulling in the vertical direction: Not acceptable Rotation in the vertical direction: Up to a maximum of 10 times When you use the cable by turning it back 21 FX15 Series1mm Pitch Wire-to-Board Connectors supporting LVDS signal Precautions and recommendations Handling of Connectors after Mating Do not to apply excessive force to the connectors when routing the cable after mating. Pulling on the entire cable with a force of 20N or greater can damage the connector. Please take care not to pull the cable. Un-mating of the connectors Equally depress both sides of the latch-locks as shown on the illustration and pull the plug straight out. Do not pull on the cables! B Dec.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved. B 1 Press 1 Press 1 Press 1 Press 2Pull straight back. B Lock latches B B 22 FX15 Series1mm Pitch Wire-to-Board Connectors supporting LVDS signal BTechnical Information (FX15S Series) Eye Pattern Waveforms (700MHz) 1.5 m Cable Length Shielding Effectiveness (Shielding Characteristics Comparison Using a 2-chamber Shielded Room) Measured shielding effectiveness for frequencies from 100MHz to 2GHz. Shielded connectors show noise suppression of 10db to 20dB, when compared with connectors without the shields. 60 With cable-side shields + With PCB-side shields 50 With cable-side shields + Without PCB-side shields 40 Shielding Effect (dB) Dec.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved. 1 m Cable Length Without cable-side shields + With PCB-side shields 30 Without cable-side shields + Without PCB-side shields (0 dB line) 20 10 0 -10 0.1 0.15 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.5 2 Frequency (GHz) Notes :The measurement value of "Without plug-side shields + Without receptacle-side shields" are taken as the zero level of the graph vertical axis dB. The respective results express the noise suppression effect (dB) as a relative comparison value to the "without shields" condition as the reference. 23 Dec.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved. FX15 Series1mm Pitch Wire-to-Board Connectors supporting LVDS signal USA: HIROSE ELECTRIC (U.S.A.), INC. HEADQUARTERS 2688 Westhills Court, Simi Valley, CA 93065-6235 Phone : +1-805-522-7958 Fax : +1-805-522-3217 http://www.hirose.com/us/ USA: HIROSE ELECTRIC (U.S.A.), INC. SAN JOSE OFFICE 3255 Scott Boulevard, Building 7, Suite 101 Santa Clara, CA 95054 Phone : +1-408-253-9640 Fax : +1-408-253-9641 http://www.hirose.com/us/ USA: HIROSE ELECTRIC (U.S.A.), INC. CHICAGO OFFICE 580 Waters Edge Lane, Suite 205 Lombard IL 60148 Phone : +1-630-282-6701 Mail : inquiries@hirose.com http://www.hirose.com/us/ USA: HIROSE ELECTRIC (U.S.A.), INC. DETROIT OFFICE (AUTOMOTIVE) 17197 N. Laurel Park Drive, Suite 253, Livonia, MI 48152 Phone : +1-734-542-9963 Fax : +1-734-542-9964 http://www.hirose.com/us/ THE NETHERLANDS: HIROSE ELECTRIC EUROPE B.V. Hogehillweg #8 1101 CC Amsterdam Z-O Phone : +31-20-6557460 Fax : +31-20-6557469 http://www.hirose.com/eu/ GERMANY: HIROSE ELECTRIC EUROPE B.V. GERMAN BRANCH Herzog-Carl-Strasse 4 D-73760 Ostfildern (Scharnhauser Park) Phone : +49-711-4560-02-1 Fax : +49-711-4560-02-299 http://www.hirose.com/eu/ GERMANY: HIROSE ELECTRIC EUROPE B.V. NUERNBERG OFFICE Muggenhofer Str. 136 90429 Nuernberg Phone : +49-911 32 68 89 63 Fax : +49-911 32 68 89 69 http://www.hirose.com/eu/ GERMANY: HIROSE ELECTRIC EUROPE B.V. HANOVER OFFICE Bayernstr. 3, Haus C 30855 Langenhagen, Germany Phone : +49-511 97 82 61 30 Fax : +49-511 97 82 61 35 http://www.hirose.com/eu/ FRANCE: HIROSE ELECTRIC EUROPE B.V. PARIS OFFICE Regus La Garenne Colombes,Place de La Belgique, 71 Boulevard National La Garenne Colombes, 92250, France Phone : +33 (0) 1 7082 3170 Fax : +33 (1) 7082 3101 http://www.hirose.com/eu/ UNITED KINGDOM: HIROSE ELECTRIC EUROPE BV (UK BRANCH) 4 Newton Court, Kelvin Drive, Knowlhill, Milton Keynes, MK5 8NH Phone : +44-1908 202050 Fax : +44-1908 202058 http://www.hirose.com/eu/ CHINA: HIROSE ELECTRIC (SHANGHAI) CO., LTD. 1601, Henderson Metropolitan, NO.300, East Nanjing Road, Huangpu District, Shanghai, China 200001 Phone : +86-21-6391-3355 Fax : +86-21-6391-3335 http://www.hirose.com/cn/ CHINA: HIROSE ELECTRIC (SHANGHAI) CO.,LTD. BEIJING BRANCH A1001, Ocean International Center, Building 56# East 4th Ring Middle Road, ChaoYang District, Beijing, 100025 Phone : +86-10-5165-9332 Fax : +86-10-5908-1381 http://www.hirose.com/cn/ CHINA: HIROSE ELECTRIC TECHNOLOGIES (SHENZHEN) CO., LTD. Room 09-13, 19/F, Office Tower Shun Hing Square, Di Wang Commercial Centre, 5002 Shen Nan Dong Road, Shenzhen City, Guangdong Province, 518008 Phone : +86-755-8207-0851 Fax : +86-755-8207-0873 http://www.hirose.com/cn/ HONG KONG: HIROSE ELECTRIC HONGKONG TRADING CO., LTD. Room 1001, West Wing, Tsim Sha Tsui Centre, 66 Mody Road, Tsim Sha Tsui East, Kowloon, Hong Kong Phone : +852-2803-5338 Fax : +852-2591-6560 http://www.hirose.com/hk/ TAIWAN: HIROSE ELECTRIC TAIWAN CO., LTD. 103 8F, No.87, Zhengzhou Rd., Taipei Phone : +886-2-2555-7377 Fax : +886-2-2555-7350 http://www.hirose.com/tw/ KOREA: HIROSE KOREA CO., LTD. 250, Huimanggongwon-ro, Siheung-si, Gyeonggi-do, Korea, 429-849 Phone : +82-31-496-7000,7124 Fax : +82-31-496-7100 http://www.hirose.co.kr/ SINGAPORE: INDIA: HIROSE ELECTRIC SINGAPORE PTE. LTD. DELHI LIAISON OFFICE HIROSE ELECTRIC SINGAPORE PTE. LTD. 10 Anson Road #26-16, International Plaza Office NO.519, Regus-Green Boulevard, Level5, Tower C, Sec62, Plot B-9A, Block B, Noida, 201301, Uttar Pradesh, India 079903, Singapore Phone : +91-12-660-8018 Phone : +65-6324-6113 Fax : +91-120-4804949 Fax : +65-6324-6123 http://www.hirose.com/sg/ http://www.hirose.com/sg/ INDIA: HIROSE ELECTRIC SINGAPORE PTE. LTD. BANGALORE LIAISON OFFICE Unit No-403, 4th Floor, No-84, Barton Centre, Mahatma Gandhi (MG) Road, Bangalore 560 001, Karnataka, India Phone : +91-80-4120 1907 Fax : +91-80-4120 9908 http://www.hirose.com/sg/ MALAYSIA: HIROSE ELECTRIC SINGAPORE PTE. LTD. 1-10-07, Suntech @ Penang Cybercity (1164),Lintang Mayang Pasir 3,11950, Bayan Baru, Penang, Malaysia. Phone : +604-619-2564 Fax : +604-619-2574 http://www.hirose.com/sg/ (R) 24 THAILAND: HIROSE ELECTRIC SINGAPORE PTE. LTD. BANGKOK OFFICE (REPRESENTATIVE OFFICE) Unit 4703, 47th FL., 1 Empire Tower, South Sathorn Road, Yannawa, Sathorn, Bangkok 10120 Thailand Phone : +66-2-686-1255 Fax : +66-2-686-3433 http://www.hirose.com/sg/ 2-6-3,Nakagawa Chuoh,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN TEL: +81-45-620-3526 Fax: +81-45-591-3726 http://www.hirose.com http://www.hirose-connectors.com The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use. The contents of this catalog are current as of date of 10/2015. Contents are subject to change without notice for the purpose of improvements.