xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 APPLICABILITY TABLE PRODUCT HE910 Mini PCIe HE910-D Mini PCIe DE910 Mini PCIe LE910-SVG Mini PCIe LE910-NVG Mini PCIe LE910-NAG Mini PCIe LE910-EUG Mini PCIe LE910-NA V2 Mini PCIe LE910-SV V2 Mini PCIe LE910-EU V2 Mini PCIe LE910-AU V2 Mini PCIe LE910-JN1 V2 Mini PCIe LE910-NA1 V2 Mini PCIe LE910-EU1 V2 Mini PCIe LE910-SV1 V2 Mini PCIe Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 2 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Notice While reasonable efforts have been made to assure the accuracy of this document, Telit assumes no liability resulting from any inaccuracies or omissions in this document, or from use of the information obtained herein. The information in this document has been carefully checked and is believed to be entirely reliable. However, no responsibility is assumed for inaccuracies or omissions. Telit reserves the right to make changes to any products described herein and reserves the right to revise this document and to make changes from time to time in content hereof with no obligation to notify any person of revisions or changes. Telit does not assume any liability arising out of the application or use of any product, software, or circuit described herein; neither does it convey license under its patent rights or the rights of others. It is possible that this publication may contain references to, or information about Telit products (machines and programs), programming, or services that are not announced in your country. Such references or information must not be construed to mean that Telit intends to announce such Telit products, programming, or services in your country. Copyrights This instruction manual and the Telit products described in this instruction manual may be, include or describe copyrighted Telit material, such as computer programs stored in semiconductor memories or other media. Laws in the Italy and other countries preserve for Telit and its licensors certain exclusive rights for copyrighted material, including the exclusive right to copy, reproduce in any form, distribute and make derivative works of the copyrighted material. Accordingly, any copyrighted material of Telit and its licensors contained herein or in the Telit products described in this instruction manual may not be copied, reproduced, distributed, merged or modified in any manner without the express written permission of Telit. Furthermore, the purchase of Telit products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Telit, as arises by operation of law in the sale of a product. Computer Software Copyrights The Telit and 3rd Party supplied Software (SW) products described in this instruction manual may include copyrighted Telit and other 3rd Party supplied computer programs stored in semiconductor memories or other media. Laws in the Italy and other countries preserve for Telit and other 3rd Party supplied SW certain exclusive rights for copyrighted computer programs, including the exclusive right to copy or reproduce in any form the copyrighted computer program. Accordingly, any copyrighted Telit or other 3rd Party supplied SW computer programs contained in the Telit products described in this instruction manual may not be copied (reverse engineered) or reproduced in any manner without the express written permission of Telit or the 3rd Party SW supplier. Furthermore, the purchase of Telit products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Telit or other 3rd Party supplied SW, except for the normal nonexclusive, royalty free license to use that arises by operation of law in the sale of a product. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 3 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 Usage and Disclosure Restrictions License Agreements The software described in this document is the property of Telit and its licensors. It is furnished by express license agreement only and may be used only in accordance with the terms of such an agreement. Copyrighted Materials Software and documentation are copyrighted materials. Making unauthorized copies is prohibited by law. No part of the software or documentation may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, without prior written permission of Telit High Risk Materials Components, units, or third-party products used in the product described herein are NOT fault-tolerant and are NOT designed, manufactured, or intended for use as on-line control equipment in the following hazardous environments requiring fail-safe controls: the operation of Nuclear Facilities, Aircraft Navigation or Aircraft Communication Systems, Air Traffic Control, Life Support, or Weapons Systems (High Risk Activities"). Telit and its supplier(s) specifically disclaim any expressed or implied warranty of fitness for such High Risk Activities. Trademarks TELIT and the Stylized T Logo are registered in Trademark Office. All other product or service names are the property of their respective owners. Copyright (c) Telit Communications S.p.A. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 4 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 Contents 1. INTRODUCTION........................................................................................................................................................... 7 1.1. 1.2. 1.3. 1.4. 1.5. SCOPE ....................................................................................................................................................................... 7 AUDIENCE ................................................................................................................................................................. 7 CONTACT INFORMATION, SUPPORT........................................................................................................................... 7 TEXT CONVENTIONS ................................................................................................................................................. 8 RELATED DOCUMENTS ............................................................................................................................................. 8 2. OVERVIEW .................................................................................................................................................................... 9 3. XE910 MINI PCI EXPRESS CARD CONNECTIONS............................................................................................. 10 3.1. 3.2. 4. PIN-OUT ................................................................................................................................................................ 10 ANTENNA CONNECTORS ......................................................................................................................................... 11 POWER SUPPLY ......................................................................................................................................................... 13 4.1. 4.2. 5. POWER SUPPLY REQUIREMENTS ............................................................................................................................. 13 POWER CONSUMPTION ............................................................................................................................................ 14 GSM/WCDMA/LTE /CDMA RADIO SECTION ..................................................................................................... 15 5.1. XE910 MINI PCI PRODUCT VARIANTS .................................................................................................................... 15 5.2. TX AND RX CHARACTERISTICS............................................................................................................................... 15 5.3. GSM/WCDMA/LTE/CDMA ANTENNA REQUIREMENTS ...................................................................................... 17 5.3.1. GSM/WCDMA/LTE/CDMA Antenna - Installation Guidelines ..................................................................... 21 5.4. ANTENNA DIVERSITY REQUIREMENTS .................................................................................................................... 22 5.5. GNSS RECEIVER..................................................................................................................................................... 26 5.5.1. GNSS Performances ...................................................................................................................................... 26 5.5.2. GNSS RF Front End Design .......................................................................................................................... 27 6. LOGIC LEVEL SPECIFICATIONS .......................................................................................................................... 28 7. USB PORT..................................................................................................................................................................... 28 7.1. USB 2.0 HS ............................................................................................................................................................ 28 8. SIM INTERFACE ........................................................................................................................................................ 29 9. CONTROL SIGNALS .................................................................................................................................................. 30 9.1. 9.2. 9.3. 9.4. 10. 10.1. 10.2. 11. 11.1. 11.2. WAKE# .................................................................................................................................................................. 30 W_DISABLE# ....................................................................................................................................................... 32 LED_WWAN# ....................................................................................................................................................... 32 PERST#.................................................................................................................................................................. 32 AUDIO SECTION OVERVIEW ............................................................................................................................ 33 ELECTRICAL CHARACTERISTICS ............................................................................................................................. 34 CODEC EXAMPLE .................................................................................................................................................. 34 MECHANICAL SPECIFICATIONS ..................................................................................................................... 35 WEIGHT ................................................................................................................................................................ 36 ENVIRONMENTAL REQUIREMENTS .............................................................................................................. 36 12. PACKING SYSTEM ................................................................................................................................................ 37 13. SAFETY RECOMMANDATIONS......................................................................................................................... 38 14. CONFORMITY ASSESSMENT ISSUES .............................................................................................................. 39 Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 5 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 14.1. 1999/5/EC DIRECTIVE (HE910).............................................................................................................................. 39 14.2. FCC/IC REGULATORY NOTICES (HE910) ............................................................................................................... 42 14.3. 1999/5/EC DIRECTIVE (LE910) .............................................................................................................................. 44 14.4. FCC/IC REGULATORY NOTICES (LE910) ................................................................................................................ 47 14.5. CONFORMITY ASSESSMENT ISSUES / PROBLEMES D'EVALUATION DE CONFORMITE (DE910) ................................. 50 14.6. CONFORMITY ASSESSMENT ISSUES (LE910 V2) ......................................................................................... 52 14.6.1. FCC/IC Regulatory notices ........................................................................................................................... 52 14.7. SAFETY RECOMMENDATIONS (LE910 V2).............................................................................................................. 55 14.8. SAFETY RECOMMENDATIONS (HE910) ................................................................................................................... 57 14.9. SAFETY RECOMMENDATIONS (DE910) ................................................................................................................... 57 15. DOCUMENT HISTORY ......................................................................................................................................... 58 Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 6 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 1. 1.1. Introduction Scope The aim of this document is the description of some hardware solutions useful for developing a product with the Telit xE910 Mini PCIe Adapter. 1.2. Audience This document is intended for Telit customers, who are integrators, about to implement their applications using our xE910 Mini PCIe Adapter. 1.3. Contact Information, Support For general contact, technical support, to report documentation errors and to order manuals, contact Telit's Technical Support Center (TTSC) at: TS-EMEA@telit.com TS-NORTHAMERICA@telit.com TS-LATINAMERICA@telit.com TS-APAC@telit.com Alternatively, use: http://www.telit.com/en/products/technical-support-center/contact.php For detailed information about where you can buy the Telit modules or for recommendations on accessories and components visit: http://www.telit.com To register for product news and announcements or for product questions contact Telit's Technical Support Center (TTSC). Our aim is to make this guide as helpful as possible. Keep us informed of your comments and suggestions for improvements. Telit appreciates feedback from the users of our information. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 7 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 1.4. Text Conventions Danger - This information MUST be followed or catastrophic equipment failure or bodily injury may occur. Caution or Warning - Alerts the user to important points about integrating the module, if these points are not followed, the module and end user equipment may fail or malfunction. Tip or Information - Provides advice and suggestions that may be useful when integrating the module. All dates are in ISO 8601 format, i.e. YYYY-MM-DD. 1.5. Related Documents * * * * * * * * * * HE910/UE910 AT Commands Reference Guide 80378ST10091a HE910 Hardware User Guide 1vv03700925 Event Monitor Application Note 80000nt10043a Digital Voice Interface Application Note 80000NT10004a LE910 AT Commands Reference Guide 80378ST10585a LE910 Hardware User Guide 1vv03701089 LE910 Digital Voice Interface Application Note 80000NT11246a DE910 Hardware User Guide 1vv03700951 LE910-V2 Modules AT Commands Reference Guide 80446ST10707A LE910-V2 Hardware User Guide 1VV0301200 Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 8 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 2. Overview The aim of this document is the description of some hardware solutions useful for developing a product that will host the Telit XE910 Mini PCIe Adapter. In this document all the basic functions of a mobile phone will be taken into account; for each one of them a proper hardware solution will be suggested and eventually the wrong solutions and common errors to be avoided will be evidenced. Obviously this document cannot embrace the whole hardware solutions and products that may be designed. The wrong solutions to be avoided shall be considered as mandatory, while the suggested hardware configurations shall not be considered mandatory, instead the information given shall be used as a guide and a starting point for properly developing your product with the Telit Mini PCIe module. NOTICE: (EN) The integration of the GSM/GPRS/WCDMA XE910 Mini PCIe cellular module within user application shall be done according to the design rules described in this manual. (IT) L'integrazione del modulo cellulare GSM/GPRS/WCDMA XE910 Mini PCIe all'interno dell'applicazione dell'utente dovra rispettare le indicazioni progettuali descritte in questo manuale. (DE) Die Integration des XE910 Mini PCIe GSM/GPRS/WCDMA Mobilfunk-Moduls in ein Gerat mu gema der in diesem Dokument beschriebenen Kunstruktionsregeln erfolgen. (SL) Integracija GSM/GPRS/WCDMA XE910 Mini PCIe modula v uporabniki aplikaciji bo morala upotevati projektna navodila, opisana v tem prironiku. (SP) La utilizacion del modulo GSM/GPRS/WCDMA XE910 Mini PCIe debe ser conforme a los usos para los cuales ha sido desenado descritos en este manual del usuario. (FR) L'integration du module cellulaire GSM/GPRS/WCDMA XE910 Mini PCIe dans l'application de l'utilisateur sera faite selon les regles de conception decrites dans ce manuel. (HE) XE910 Mini PCIe The information presented in this document is believed to be accurate and reliable. However, no responsibility is assumed by Telit Communications S.p.A. for its use, nor any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent rights of Telit Communications S.p.A. other than for circuitry embodied in Telit products. This document is subject to change without notice. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 9 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 3. xE910 Mini PCI express card connections 3.1. PIN-OUT This product has a standard Mini PCI express connector, excepting the (4) audio signals which use normally reserved connectors. Pin Signal I/O Function Type Power Supply 2 3V3_AUX O 3.3V supply Power 24 3V3 O 3.3V supply Power 39 3V3_AUX O 3.3V supply Power 41 3V3_AUX O 3.3V supply Power 52 3V3_AUX O 3.3V supply Power 4 GND - Ground Power 9 GND - Ground Power 15 GND - Ground Power 18 GND - Ground Power 21 GND - Ground Power 26 GND - Ground Power 27 GND - Ground Power 29 GND - Ground Power 34 GND - Ground Power 35 GND - Ground Power 37 GND - Ground Power 40 GND - Ground Power 43 GND - Ground Power 50 GND - Ground Power SIM Card Interface 8 SIMVCC O External SIM signal - Power supply for the SIM 1.8 / 3V 10 SIMIO I/O External SIM signal - Data I/O 1.8 / 3V 12 SIMCLK O External SIM signal - Clock 1.8 / 3V 14 SIMRST O External SIM signal - Reset 1.8 / 3V 36 USB D- I/O USB differential Data (-) 0.3...2.8V 38 USB D+ I/O USB differential Data (+) 0.3...2.8V USB Pi Signal n I/O Function Type Miscellaneous Functions Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 10 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 1 WAKE# O Active low signal used to wake up the system from stand-by 3.3V 20 WDISABLE# I Active low signal for wireless disabling (Flight mode) 3.3V 22 PERST# I Active low functional reset to the card 3.3V 42 LED_WWAN# O Active low, open drain signal for WWAN LED driving, used to provide 3.3V...5V module's status indication Digital Voice Interface (DVI) 45 PCM_CLK I/O Digital Audio Interface (CLK) CMOS 1.8V 47 PCM_RX I Digital Audio Interface (RX) CMOS 1.8V 49 PCM_TX O Digital Audio Interface (TX) CMOS 1.8V 51 PCM_SYNC I/O Digital Audio Interface (SYNC) CMOS 1.8V N.C. 3.2. 3 - 5 - 6 - 7 - 11 - 13 - 16 - 17 - 19 - 23 - 25 - 28 - 30 - 31 - 32 - 33 - 44 - 46 - 48 - Antenna Connectors The xE910 Mini PCIe adapter is equipped with a set of 50 RF U.FL. connectors from Hirose U.FL-R-SMT-1(10). Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 11 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 The available connectors are: * Main RF antenna (ANT) * RX Diversity Antenna (DIV) * GNSS Antenna (GPS) See the picture on the right for their position on the interface. The presence of all the connectors is depending on the product characteristics and supported functionalities. For more information about mating connectors, visit the website http://www.hirose-connectors.com/ Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 12 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 4. Power Supply The power supply circuitry and board layout are a very important part in the full product design and they strongly reflect on the product overall performances, hence read the requirements carefully and the guidelines that will follow for a proper design. 4.1. Power Supply Requirements The external power supply must be connected to the pins 2, 39, 41, 52 and must fulfill the following requirements: POWER SUPPLY Nominal Supply Voltage Normal Operating Voltage Range 3.3 V 3.00 V/ 3.60 V NOTE: The Operating Voltage Range MUST never be exceeded; care must be taken when designing the application's power supply section to avoid having an excessive voltage drop. If the voltage drop is exceeding the limits it could cause a Power Off of the module. NOTE: Overshoot voltage (regarding MAX Operating Voltage) and drop in voltage (regarding MIN Operating Voltage) MUST never be exceeded; Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 13 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 4.2. Power Consumption Please refer to the Module's Hardware User guide for the details The GSM system is made in a way that the RF transmission is not continuous, else it is packed into bursts at a base frequency of about 216 Hz, and the relative current peaks can be as high as about 2.4A. Therefore the power supply has to be designed in order to withstand with these current peaks without big voltage drops; this means that both the electrical design and the board layout must be designed for this current flow. If the voltage drop during the peak current absorption is too much, then the device may even shutdown as a consequence of the supply voltage drop. NOTE: The electrical design for the Power supply should be made ensuring it will be capable of a peak current output of at least 2.4 A. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 14 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 5. 5.1. GSM/WCDMA/LTE /CDMA Radio Section xE910 Mini PCI Product Variants The following table is listing the main differences between the xE910 variants: Product LE910-NA1 V2 LE910-SV1 V2 LE910-EU1 V2 LE910-JN1 V2 LE910-NA V2 LE910-SV V2 LE910-EU V2 LE910-AU V2 3G Bands LTE Bands B2, B4, B5, B12/B17 (B13) CDMA Bands Not supported B2, B4, B13 NO Not supported B3, B7, B20, B1, B8 NO Not supported B1, B19, B21 NO B5, B2 B2, B4, B5, B12/B17 (B13) NO Not supported B2, B4, B13 NO B1, B8 B3, B7, B20, B1, B8 NO Not supported B3, B7, B28 NO B20 (800), B3 (1800), B7 (2600) NO YES NO YES NO YES B5, B2 LE910-EUG GSM 900, DCS1800 B5(850), B8 (900), B1 (2100) LE910-NAG GSM 850, PCS 1900 B5(850), B2(1900) LE910-NVG Not supported B5(850), B2(1900) LE910-SVG HE910 HE910-D DE910-DUAL 5.2. 2G Bands Not supported Not supported GSM 900, DCS1800 Not supported Not supported Not supported GSM 900, DCS1800 Not supported Not supported GSM 850, GSM 900, DCS1800, PCS 1900 GSM 850, GSM 900, DCS1800, PCS 1900 Not supported NO B17(700), B5(850), B4(1700), B2(1900) B13(700), B4(1700) GNSS NO NO NO NO NO NO NO NO Not supported B13(700), B4(1700) NO YES FDD B1, B2, B4, B5, B8 Not supported NO YES FDD B1, B2, B4, B5, B8 Not supported NO NO Not supported Not supported BC0, BC1 YES TX and RX characteristics Please refer to the Module's Hardware User guide for the details Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 15 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 16 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 5.3. GSM/WCDMA/LTE/CDMA Antenna Requirements The antenna connection is one of the most important aspect in the full product design as it strongly affects the product overall performances, hence read carefully and follow the requirements and the guidelines for a proper design. The xE910 Mini PCIe adapter is provided with three RF connectors. The available connectors are: * Main RF antenna (ANT) * RX Diversity Antenna (DIV) * GNSS Antenna (GPS) Connecting cables between the module and the antenna must have 50 impedance. If the impedance of the module is mismatched, RF performance is reduced significantly. If the host device is not designed to use the module's diversity or GPS antenna, terminate the interface with a 50 load. MAIN ANTENNA REQUIREMENTS for LE910-NA V2 and LE910-NA1 Depending by frequency band(s) provided by the network Frequency range operator, the customer shall use the most suitable antenna for that/those band(s) Bandwidth 140 MHz in LTE/WCDMA Band 2 445 MHz in LTE Band 4 70 MHz in LTE/WCDMA Band 5 47 MHz in LTE Band 12 41 MHz in LTE Band 13 Impedance Input power VSWR absolute max VSWR recommended 50 ohm > 24dBm Average power in WCDMA & LTE 10:1 (limit to avoid permanent damage) 2:1 (limit to fulfil all regulatory requirements) MAIN ANTENNA REQUIREMENTS for LE910-SV V2 and LE910-SV1 Depending by frequency band(s) provided by the network Frequency range operator, the customer shall use the most suitable antenna for that/those band(s) Bandwidth 140 MHz in LTE/WCDMA Band 2 445 MHz in LTE Band 4 41 MHz in LTE Band 13 Impedance Input power VSWR absolute max VSWR recommended 50 ohm > 24dBm Average power in WCDMA & LTE 10:1 (limit to avoid permanent damage) 2:1 (limit to fulfil all regulatory requirements) Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 17 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 MAIN ANTENNA REQUIREMENTS for LE910-AU V2 Depending by frequency band(s) provided by the network Frequency range operator, the customer shall use the most suitable antenna for that/those band(s) Bandwidth 170 MHz in LTE Band 3 190 MHz in LTE Band 7 100 MHz in LTE Band 28 Impedance Input power VSWR absolute max VSWR recommended 50 ohm > 24dBm Average power in WCDMA & LTE 10:1 (limit to avoid permanent damage) 2:1 (limit to fulfil all regulatory requirements) MAIN ANTENNA REQUIREMENTS for LE910-EU V2 and LE910-EU1 Depending by frequency band(s) provided by the network Frequency range operator, the customer shall use the most suitable antenna for that/those band(s) Bandwidth 250 MHz in LTE/WCDMA Band 1 170 MHz in LTE/WCDMA Band 3 / DCS1800 190 MHz in LTE Band 7 80 MHz in LTE/WCDMA Band 8 / GSM900 71 MHz in LTE Band 20 Impedance Input power VSWR absolute max VSWR recommended 50 ohm > 24dBm Average power in WCDMA & LTE 10:1 (limit to avoid permanent damage) 2:1 (limit to fulfil all regulatory requirements) Frequency range MAIN ANTENNA REQUIREMENTS for LE910-JN1 Depending by frequency band(s) provided by the network operator, the customer shall use the most suitable antenna for that/those band(s) Bandwidth 250 MHz in LTE Band 1 60 MHz in LTE Band 19 63 MHz in LTE Band 21 Impedance Input power VSWR absolute max VSWR recommended 50 ohm > 24dBm Average power in WCDMA & LTE 10:1 (limit to avoid permanent damage) 2:1 (limit to fulfil all regulatory requirements) MAIN ANTENNA REQUIREMENTS for LE910-EUG Depending by frequency band(s) provided by the network Frequency range operator, the customer shall use the most suitable antenna for that/those band(s) GSM900 : 80 MHz Bandwidth (GSM/EDGE) GSM1800(DCS) : 170 MHz Bandwidth WCDMA band I(2100) : 250 MHz (WCDMA) WCDMA band V(850) : 70 MHz Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 18 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 Bandwidth (LTE) Impedance Input power VSWR absolute max VSWR recommended WCDMA band VIII(900) : 80 MHz LTE band III(1800) : 170 MHz LTE Band VII(2600) : 190 MHz LTE Band XX(800) : 71 MHz 50 ohm > 33dBm(2 W) peak power in GSM > 24dBm Average power in WCDMA & LTE 10:1 (limit to avoid permanent damage) 2:1 (limit to fulfil all regulatory requirements) MAIN ANTENNA REQUIREMENTS for LE910-NAG Depending by frequency band(s) provided by the network Frequency range operator, the customer shall use the most suitable antenna for that/those band(s) GSM850 : 70 MHz Bandwidth (GSM/EDGE) GSM1900(PCS) : 140 MHz Bandwidth WCDMA band II(1900) : 140 MHz (WCDMA) WCDMA band V(850) : 70 MHz LTE Band II(1900) : 140 MHz Bandwidth LTE Band IV(1700) : 445 MHz (LTE) LTE Band V (850) : 70 MHz LTE Band XVII(700) : 42 MHz Impedance 50 ohm > 33dBm(2 W) peak power in GSM Input power > 24dBm Average power in WCDMA & LTE VSWR absolute max 10:1 (limit to avoid permanent damage) VSWR recommended 2:1 (limit to fulfil all regulatory requirements) MAIN ANTENNA REQUIREMENTS for LE910-NVG Depending by frequency band(s) provided by the network Frequency range operator, the customer shall use the most suitable antenna for that/those band(s) Bandwidth WCDMA band II(1900) : 140 MHz (WCDMA) WCDMA band V(850) : 70 MHz Bandwidth LTE Band IV(1700) : 445 MHz (LTE) LTE Band XIII(700) : 41 MHz Impedance 50 ohm Input power > 24dBm Average power in WCDMA & LTE VSWR absolute max 10:1 (limit to avoid permanent damage) VSWR recommended 2:1 (limit to fulfil all regulatory requirements) Frequency range MAIN ANTENNA REQUIREMENTS for LE910-SVG Depending by frequency band(s) provided by the network operator, the customer shall use the most suitable antenna for Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 19 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 Bandwidth (LTE) Impedance Input power VSWR absolute max VSWR recommended that/those band(s) LTE Band IV(1700) : 445 MHz LTE Band XIII(700) : 41 MHz 50 ohm > 24dBm Average power 10:1 (limit to avoid permanent damage) 2:1 (limit to fulfil all regulatory requirements) MAIN ANTENNA REQUIREMENTS for HE910 Depending by frequency band(s) provided by the network Frequency range operator, the customer shall use the most suitable antenna for that/those band(s) 70 MHz in GSM850, 80 MHz in GSM900, 170 MHz in DCS & 140 Bandwidth (GSM/EDGE) MHz PCS band 70 MHz in WCDMA Band V 80 MHz in WCDMA Band VIII Bandwidth 460 MHz in WCDMA Band IV (WCDMA) 140 MHz in WCDMA Band II 250 MHz in WCDMA Band I Impedance 50 ohm > 33dBm(2 W) peak power in GSM Input power > 24dBm Average power in WCDMA VSWR absolute max 10:1 (limit to avoid permanent damage) VSWR recommended 2:1 (limit to fulfil all regulatory requirements) MAIN ANTENNA REQUIREMENTS for DE910-DUAL Depending by frequency band(s) provided by the network Frequency range operator, the customer shall use the most suitable antenna for that/those band(s) 70 MHz in CDMA BC0 Bandwidth 140 MHz in CDMA BC1 Gain < 5.12dBi in CDMA BC0 Gain Gain < 6.12dBi in CDMA BC1 Impedance 50 ohm Input power > 24.4dBm Average Power in CDMA VSWR absolute max 5:1 (Limit to avoid permanent damage) VSWR recommended 2:1 (limit to fulfil all regulatory requirements) Please refer to the Module's Hardware User guide for the details Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 20 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 5.3.1. GSM/WCDMA/LTE/CDMA Antenna - Installation Guidelines * Install the antenna in a place covered by the GSM/WCDMA/LTE/CDMA signal. * If the device antenna is located greater then 20cm from the human body and there are no co-located transmitters then the Telit FCC/IC approvals can be re-used by the end product * If the device antenna is located less than 20cm from the human body or there are no co-located transmitters then the additional FCC/IC testing may be required for the end product (Telit FCC/IC approvals cannot be reused) * Antenna shall not be installed inside metal cases * Antenna shall be installed also according antenna manufacturer instructions. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 21 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 5.4. Antenna Diversity Requirements This product includes an input for a second RX antenna to improve the radio sensitivity. The function is called Antenna Diversity. DIVERSITY ANTENNA REQUIREMENTS for LE910-NA V2 and LE910-NA1 Depending by frequency band(s) provided by the network Frequency range operator, the customer shall use the most suitable antenna for that/those band(s) Bandwidth 60 MHz in LTE/WCDMA Band 2 45 MHz in LTE Band 4 25 MHz in LTE/WCDMA Band 5 15 MHz in LTE Band 12 10 MHz in LTE Band 13 Impedance VSWR recommended 50 ohm 2:1 (limit to fulfil all regulatory requirements) DIVERSITY ANTENNA REQUIREMENTS for LE910-SV V2 and LE910-SV1 Depending by frequency band(s) provided by the network Frequency range operator, the customer shall use the most suitable antenna for that/those band(s) Bandwidth 60 MHz in LTE/WCDMA Band 2 45 MHz in LTE Band 4 10 MHz in LTE Band 13 Impedance VSWR recommended 50 ohm 2:1 (limit to fulfil all regulatory requirements) DIVERSITY ANTENNA REQUIREMENTS for LE910-AU V2 Depending by frequency band(s) provided by the network Frequency range operator, the customer shall use the most suitable antenna for that/those band(s) Bandwidth 75 MHz in LTE Band 3 70 MHz in LTE Band 7 45 MHz in LTE Band 28 Impedance VSWR recommended 50 ohm 2:1 (limit to fulfil all regulatory requirements) Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 22 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 DIVERSITY ANTENNA REQUIREMENTS for LE910-EU V2 Depending by frequency band(s) provided by the network Frequency range operator, the customer shall use the most suitable antenna for that/those band(s) Bandwidth 60 MHz in LTE/WCDMA Band 1 75 MHz in LTE/WCDMA Band 3 / DCS1800 70 MHz in LTE Band 7 35 MHz in LTE/WCDMA Band 8 / GSM900 30 MHz in LTE Band 20 Impedance VSWR recommended 50 ohm 2:1 (limit to fulfil all regulatory requirements) DIVERSITY ANTENNA REQUIREMENTS for LE910-JN1 Depending by frequency band(s) provided by the network Frequency range operator, the customer shall use the most suitable antenna for that/those band(s) Bandwidth 60 MHz in LTE Band 1 15 MHz in LTE Band 19 15 MHz in LTE Band 21 Impedance VSWR recommended 50 ohm 2:1 (limit to fulfil all regulatory requirements) DIVERSITY ANTENNA REQUIREMENTS for LE910-EUG Depending by frequency band(s) provided by the network Frequency range operator, the customer shall use the most suitable antenna for that/those band(s) WCDMA band I(2100) : 250 MHz Bandwidth WCDMA band V(850) : 70 MHz (WCDMA) WCDMA band VIII(900) : 80 MHz LTE band III(1800) : 170 MHz Bandwidth LTE Band VII(2600) : 190 MHz (LTE) LTE Band XX(800) : 71 MHz Impedance 50 ohm VSWR recommended 2:1 (limit to fulfil all regulatory requirements) DIVERSITY ANTENNA REQUIREMENTS for LE910-NAG Depending by frequency band(s) provided by the network Frequency range operator, the customer shall use the most suitable antenna for that/those band(s) Bandwidth WCDMA band II(1900) : 140 MHz (WCDMA) WCDMA band V(850) : 70 MHz LTE Band II(1900) : 140 MHz Bandwidth LTE Band IV(1700) : 445 MHz (LTE) LTE Band V (850) : 70 MHz LTE Band XVII(700) : 42 MHz Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 23 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 Impedance VSWR recommended 50 ohm 2:1 (limit to fulfil all regulatory requirements) Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 24 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 DIVERSITY ANTENNA REQUIREMENTS for LE910-NVG Depending by frequency band(s) provided by the network Frequency range operator, the customer shall use the most suitable antenna for that/those band(s) Bandwidth WCDMA band II(1900) : 140 MHz (WCDMA) WCDMA band V(850) : 70 MHz Bandwidth LTE Band IV(1700) : 445 MHz (LTE) LTE Band XIII(700) : 41 MHz Impedance 50 ohm VSWR recommended 2:1 (limit to fulfil all regulatory requirements) DIVERSITY ANTENNA REQUIREMENTS for LE910-SVG Depending by frequency band(s) provided by the network Frequency range operator, the customer shall use the most suitable antenna for that/those band(s) Bandwidth LTE Band IV(1700) : 445 MHz (LTE) LTE Band XIII(700) : 41 MHz Impedance 50 ohm VSWR recommended 2:1 (limit to fulfil all regulatory requirements) DIVERSITY ANTENNA REQUIREMENTS for HE910 Depending by frequency band(s) provided by the network Frequency range operator, the customer shall use the most suitable antenna for that/those band(s) Bandwidth (GSM/EDGE) 70 MHz in GSM850, 80 MHz in GSM900 & 140 MHz PCS band 70 MHz in WCDMA Band V Bandwidth 80 MHz in WCDMA Band VIII (WCDMA) 140 MHz in WCDMA Band II 250 MHz in WCDMA Band I Impedance 50 ohm VSWR recommended 2:1 (limit to fulfil all regulatory requirements) DIVERSITY ANTENNA REQUIREMENTS for DE910-DUAL Depending by frequency band(s) provided by the network Frequency range operator, the customer shall use the most suitable antenna for that/those band(s) Bandwidth 70 MHz in CDMA BC0 140 MHz in CDMA BC1 Impedance 50 ohm VSWR recommended 2:1 (limit to fulfil all regulatory requirements) Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 25 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 The second Rx antenna should not be located in the close vicinity of main antenna. In order to improve Diversity Gain, Isolation and reduce mutual interaction, the two antennas should be located at the maximum reciprocal distance possible, taking into consideration the available space in the application. NOTE1: On HE910 the diversity is not supported on the FDD BAND IV and DCS band. NOTE2: In case of HE910, if the RX Diversity is not used/connected, disable the Diversity functionality using the AT#RXDIV command (ref to the At User guide for the proper syntax). 5.5. GNSS Receiver The XE910 Mini PCIe adapter integrates a GNSS receiver that could be used in Standalone mode and in A-GPS (assisted GPS), according to the different configurations. The supported technologies are described in the following table: 5.5.1. Product GPS GLONASS LE910-EUG YES YES LE910-NAG YES YES LE910-NVG YES YES LE910-SVG YES YES HE910 YES NO HE910-D NO NO DE910-DUAL YES YES LE910-NA V2 NO NO LE910-SV V2 NO NO LE910-EU V2 NO NO LE910-AU V2 NO NO GNSS Performances Please refer to the Module's Hardware User guide for the details Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 26 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 5.5.2. GNSS RF Front End Design The xE910 Mini PCIe adapter contains an integrated LNA and pre-select SAW filter. This allows the module to work well with a passive GPS antenna. If the antenna cannot be located near the xE910, then an active antenna (that is, an antenna with a low noise amplifier built in) can be used with an external dedicated power supply circuit. NOTE: Please refer to the Module's Hardware User Guide for detailed information about GPS operating modes and RF signal requirements. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 27 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 6. Logic level specifications The following table shows logic level specifications used in the xE910 interface circuits: Absolute Maximum Ratings -Not Functional Parameter Min Max Input level on any digital pin (CMOS 1. with respect to ground -0.5V 3.6V Operating Range - DC Specification for 3V3 Logic Signalling Symbol Min Max 3V3, 3V3_AUX Supply voltage 3.0V 3.6V VIH Input high level 2.0V 3.6V VIL Input low level -0.5V 0.8V VOH Output high level 2.0V 3.6V VOL Output low level -0.5V 0.8V Input Leakage Current Output Low Current for open-drain signals -10A 10A IIN IOL 7. Parameter 4mA USB Port The xE910 Mini PCIe adapter includes one integrated universal serial bus (USB) transceiver, compliant with the standard USB 2.0 for high speed (HS) operations. 7.1. USB 2.0 HS This port is compliant with the USB 2.0 specifications. The following table lists the available signals: PAD Signal I/O Function Type 38 USB_D+ I/O USB differential Data (+) 0.3...2.8V 36 USB_D- I/O USB differential Data (-) 0.3...2.8V The USB interface is powered directly from the 3V3 supply. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 28 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 8. SIM interface The SIM pins provide the connections necessary to interface to a SIM socket located on the host device. Voltage levels over this interface comply with 3GPP standards. SIM Card Interface 8 SIMVCC O External SIM signal - Power supply for the SIM 1.8 / 3V 10 SIMIO I/O External SIM signal - Data I/O 1.8 / 3V 12 SIMCLK O External SIM signal - Clock 1.8 / 3V 14 SIMRST O External SIM signal - Reset 1.8 / 3V Following picture depicts the external SIM recommended connections: NOTE: DO NOT TERMINATE PINS 8, 10, 12, 14 WHEN USING MODEL INCLUDING SIM CARD HOLDER. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 29 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 9. Control signals The XE910 Mini PCIe provides signals for module control, as described in the following table: Pin Signal I/O Function 1 WAKE# O Active low signal used to wake up the system from stand-by 3.3V 20 W_DISABLE# I Active low signal for wireless disabling (Airplane mode) 3.3V 22 PERST# I Active low functional reset to the card 3.3V O Active low, open drain signal for WWAN LED driving, used to provide module's status indication 3.3V...5V 42 9.1. LED_WWAN# Type WAKE# WAKE# is driven, by default, by the module according the PCI Express Mini Card Electromechanical Specification Revision 1.2. NOTE: WAKE# IS NOT SUPPORTED IN HOST USING PCI EXPRESS MINI CARD ELECTROMECHANICAL SPECIFICATION REVISION 1.1 AND BELOW. NOTE: THIS SIGNAL IS NOT ACTIVE BY DEFAULT. IF DESIRED IT CAN BE CONFIGURED REMAPPING AN EVENT UNDER MONITORING THROUGH AT#EVMONI. FOR DETAILS REFER TO THE AT COMMAND USER GUIDE Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 30 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 Following picture shows the internal WAKE# driver: WAKE# output may be connected to an edge sensitive application input (e.g. a microcontroller input with IRQ enabled). No external pull-up is needed, since it is internally implemented. EXAMPLE: In the following example, a RING monitor activates the WAKEUP signal. (cf. Event Monitor App.Note 80000nt10043a) AT#ENAEVMONI=0 AT#GPIO=3,0,1 AT#ENAEVMONICFG=3,1,2 AT#EVMONI="RING",0,1,3 AT#EVMONI="RING",0,0,"AT#GPIO=3,1,1" AT#EVMONI="RING",1 AT#EVMONI="GPIO1",1,1,3 AT#EVMONI="GPIO1",1,2,1 AT#EVMONI="GPIO1",1,3,5 AT#EVMONI="GPIO1",1,0," AT#GPIO=3,0,1" reset" AT#EVMONI="GPIO1",1 AT#ENAEVMONI=1 //disable all events //Set GPIO3=>'0', "WAKE signal reset" //AT port setting //event 0-RING, after 3 rings //GPIO3=>'1', "WAKE signal active" //event 0-RING enabled //event 1-GPIO3 //when goes hi //after 5s //Set GPIO3=>'0', "WAKE signal //event 1-GPIO3 enabled //enable all events Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 31 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 9.2. W_DISABLE# W_DISABLE# is used to force the module to shut down. Thanks to its internal pull-up, leaving this pin unconnected allows the module to operate normally. This switch follows the behavior as described in the PCI-Express Mini Card specification. 9.3. LED_WWAN# LED_WWAN# is driven, by default, by the module according the PCI Express Mini Card Electromechanical Specification Revision 1.1. If desired, LED behavior can be configured by adjusting software settings. The following picture shows the internal LED_WWAN# driver and its recommended connection to a LED: Rx should be dimensioned according to typical voltage drop on application LED and to its supply voltage (3V3 to 5V). NOTE: THIS SIGNAL IS NOT ACTIVE BY DEFAULT. REFER TO AT#SLED DESCRIPTION IN THE AT COMMAND USER GUIDE 9.4. PERST# Reset Signal Signal Function I/O Pin Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 32 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 PERST# * Phone reset I 22 PERST# * is used to reset the xE910. Whenever this signal is pulled low, the xE910 is reset. When the device is reset it stops any operation. After the release of the reset the xE910 is unconditionally restarted, without doing any detach operation from the network where it is registered. The reset signal must not be used to normally restart the device, but only as an emergency exit in the rare case the device remains stuck waiting for some network response. PERST#* is internally controlled on start-up to achieve a proper power-on reset sequence, so there's no need to control this pin on start-up. It may only be used to reset a device already on that is not responding to any command. NOTE: Do not use this signal to power cycle the xE910 Mini PCIe. Use the AT#SHDN command instead. Reset Signal Operating levels: Signal Min Max RESET Input high 2.0V 3.6V RESET Input low -0.5V 0.8V * this signal is not internally pulled up so an external pull-up is required whenever the pin is not used. If PERST# is used, then it must always be connected to a push-pull output in order to allow the internal circuitry to correctly execute power on reset and under voltage lockout functions. 10. Audio Section Overview The xE910 Module does not provide an Analog Audio section. One DIGITAL AUDIO bus is available. In order to develop an application including an Analog Audio it is necessary to add a dedicated CODEC on the Application design. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 33 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 10.1. Electrical Characteristics The product provides a PCM Digital Audio Interface (DVI) on the following Pins: Digital Voice Interface (DVI) 45 PCM_CLK I/O Digital Audio Interface (CLK) CMOS 1.8V 47 PCM_RX I Digital Audio Interface (RX) CMOS 1.8V 49 PCM_TX O Digital Audio Interface (TX) CMOS 1.8V 51 PCM_SYNC I/O Digital Audio Interface (SYNC) CMOS 1.8V More details on the use of digital audio can be found in Module's DVI application Note. NOTE: THESE SIGNALS ARE 1.8V, NOT COMPATIBLE WITH Mini PCIe BUSES. THIS IS AN ADVANCED VOICE FUNCTIONALITY AND THE HOST SHOULD TAKE CARE OF CORRECT COMPATIBILITY. 10.2. CODEC Example Please refer to the Module's Digital Voice Application Note Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 34 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 11. Mechanical specifications The xE910 Mini PCIe adapters have been designed to be compliant with a standard lead-free SMT process. Moreover, it is compatible with the Mini PCIe card 52-pin card edge-type connector. The position of the antenna connectors is shown in the following picture. Soldering pads are present on the back side of the adapter board to allow the optional mounting of a sim-holder. Starting from p/n HEPCxyyy204Tzzz the carrier board has been unified to the same used on the product DE910 Mini PCIe. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 35 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 The Telit xE910 Mini PCIe adapter overall dimensions are: Length: 51.0 mm Width: 30 mm Thickness: 3.2 mm Thickness(SIM holder version): 4.78 mm The module complies with the standard dimensions specified in the PCI Express Mini Card Electromechanical Specification Revision 1.1 11.1. WEIGHT The Telit xE910 Mini PCIe adapter weight is about 10 grams. 11.2. ENVIRONMENTAL REQUIREMENTS Temperature range Storage and operating Temperature Range -40 ~ +85 C Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 36 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 12. Packing system The XE910 Mini PCIe modules are packaged on trays of 20 pieces each. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 37 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 13. SAFETY RECOMMANDATIONS READ CAREFULLY Be sure the use of this product is allowed in the country and in the environment required. The use of this product may be dangerous and has to be avoided in the following areas: Where it can interfere with other electronic devices in environments such as hospitals, airports, aircrafts, etc Where there is risk of explosion such as gasoline stations, oil refineries, etc It is rthe esponsibility of the user to enforce the country regulation and the specific environment regulation. Do not disassemble the product; any mark of tampering will compromise the warranty validity. We recommend following the instructions of the hardware user guides for a correct wiring of the product. The product has to be supplied with a stabilized voltage source and the wiring has to be conforming to the security and fire prevention regulations. The product has to be handled with care, avoiding any contact with the pins because electrostatic discharges may damage the product itself. Same cautions have to be taken for the SIM, checking carefully the instruction for its use. Do not insert or remove the SIM when the product is in power saving mode. The system integrator is responsible for the functioning of the final product; therefore, care has to be taken to the external components of the module, as well as any project or installation issue, because the risk of disturbing the GSM network or external devices or having impact on the security. Should there be any doubt, please refer to the technical documentation and the regulations in force. Every module has to be equipped with a proper antenna with specific characteristics. The antenna has to be installed with care in order to avoid any interference with other electronic devices and has to guarantee a minimum distance from the body (20 cm). In case this requirement cannot be satisfied, the system integrator has to assess the final product against the SAR regulation. The European Community provides some Directives for the electronic equipments introduced on the market. All the relevant information's are available on the European Community website: http://ec.europa.eu/enterprise/sectors/rtte/documents/ The text of the Directive 99/05 regarding telecommunication equipments is available, while the applicable Directives (Low Voltage and EMC) are available at: http://ec.europa.eu/enterprise/sectors/electrical Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 38 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 14. Conformity assessment issues The following chapters are related to the module soldered on the carrier board 14.1. 1999/5/EC Directive (HE910) The HE910 mPCIe and HE910-D mPCIe have been evaluated against the essential requirements of the 1999/5/EC Directive. Telit Communications S.p.A. , 2G/3G module 1999/5/. Czech Telit Communications S.p.A. timto prohlauje, e tento 2G/3G module je ve shod se zakladnimi poadavky a dalimi pislunymi ustanovenimi smrnice 1999/5/ES. Danish Undertegnede Telit Communications S.p.A. erklaerer herved, at folgende udstyr 2G/3G module overholder de vaesentlige krav og ovrige relevante krav i direktiv 1999/5/EF. Dutch Hierbij verklaart Telit Communications S.p.A. dat het toestel 2G/3G module in overeenstemming is met de essentiele eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. English Hereby, Telit Communications S.p.A., declares that this 2G/3G module is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Estonian Kaesolevaga kinnitab Telit Communications S.p.A. seadme 2G/3G module vastavust direktiivi 1999/5/EU pohinouetele ja nimetatud direktiivist tulenevatele teistele asjakohastele satetele. German Hiermit erklart Telit Communications S.p.A., dass sich das Gerat 2G/3G module in Ubereinstimmung mit den grundlegenden Anforderungen und den ubrigen einschlagigen Bestimmungen der Richtlinie 1999/5/EG befindet. Greek Telit Communications S.p.A. 2G/3G module 1999/5/. Hungarian Alulirott, Telit Communications S.p.A. nyilatkozom, hogy a 2G/3G module megfelel a vonatkozo alapveto kovetelmenyeknek es az 1999/5/EC iranyelv egyeb eloirasainak. Finnish Telit Communications S.p.A. vakuuttaa taten etta 2G/3G module tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sita koskevien direktiivin muiden ehtojen mukainen. French Par la presente Telit Communications S.p.A. declare que l'appareil 2G/3G module est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Icelandic Her me lysir Telit Communications S.p.A. yfir vi a 2G/3G module er i samraemi vi grunnkrofur og arar krofur, sem gerar eru i tilskipun 1999/5/EC Italian Con la presente Telit Communications S.p.A. dichiara che questo 2G/3G module e conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latvian Ar o Telit Communications S.p.A. deklar, ka 2G/3G module atbilst Direktvas 1999/5/EK btiskajm prasbm un citiem ar to saisttajiem noteikumiem. Lithuanian Siuo Telit Communications S.p.A. deklaruoja, kad is 2G/3G module atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Maltese Hawnhekk, Telit Communications S.p.A., jiddikjara li dan 2G/3G module jikkonforma mal-tiijiet essenzjali u ma provvedimenti orajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Norwegian Telit Communications S.p.A. erklaerer herved at utstyret 2G/3G module er i samsvar med de grunnleggende krav og ovrige relevante krav i direktiv 1999/5/EF. Polish Niniejszym Telit Communications S.p.A. owiadcza, e 2G/3G module jest zgodny z zasadniczymi wymogami oraz pozostaymi stosownymi postanowieniami Dyrektywy 1999/5/EC Portuguese Telit Communications S.p.A. declara que este 2G/3G module esta conforme com os requisitos essenciais e outras disposicoes da Directiva 1999/5/CE. Bulgarian Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 39 of 58 xE910 Mini PCIe Hardware User Guide Slovak Slovenian Spanish Swedish 1vv0301006 Rev.11 - 2017-05-15 Telit Communications S.p.A. tymto vyhlasuje, e 2G/3G module spa zakladne poiadavky a vetky prislune ustanovenia Smernice 1999/5/ES. Telit Communications S.p.A. izjavlja, da je ta 2G/3G module v skladu z bistvenimi zahtevami in ostalimi relevantnimi doloili direktive 1999/5/ES. Por medio de la presente Telit Communications S.p.A. declara que el 2G/3G module cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Harmed intygar Telit Communications S.p.A. att denna 2G/3G module star I overensstammelse med de vasentliga egenskapskrav och ovriga relevanta bestammelser som framgar av direktiv 1999/5/EG. In order to satisfy the essential requirements of 1999/5/EC Directive, the HE910 mPCIe is compliant to the following standards: RF spectrum use (R&TTE art. 3.2) EN 300 440-2 V1.4.1 EN 301 511 V9.0.2 EN 301 908-1 V6.2.1 EN 301 908-2 V6.2.1 EMC (R&TTE art. 3.1b) EN 301 489-1 V1.9.2 EN 301 489-3 V1.4.1 EN 301 489-7 V1.3.1 EN 301 489-24 V1.5.1 Health & Safety (R&TTE art. 3.1a) EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 EN 62311:2008 In order to satisfy the essential requirements of 1999/5/EC Directive, the HE910-D mPCIe is compliant to the following standards: RF spectrum use (R&TTE art. 3.2) EN 301 511 V9.02 EN 301 908-1 V6.2.1 EN 301 908-2 V6.2.1 EMC (R&TTE art. 3.1b) EN 301 489-1 V1.9.2 EN 301 489-7 V1.3.1 EN 301 489-24 V1.5.1 Health & Safety (R&TTE art. 3.1a) EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 EN 62311:2008 The conformity assessment procedure referred to in Article 10 and detailed in Annex V of Directive 1999/5/EC has been followed with the involvement of the following Notified Body: CETECOM ICT SERVICES GMBH Unterturkheimer Strae 6-10 66117 SAARBRUCKEN Country: Germany Notified Body Number 0682. Thus, the following marking is included in the product: The full declaration of conformity can be found on the following address: http://www.telit.com/ Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 40 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 There is no restriction for the commercialisation of the HE910 mPCIe, HE910-D mPCIe in all the countries of the European Union. Final product integrating this module must be assessed against essential requirements of the 1999/5/EC (R&TTE) Directive. It should be noted that assessment does not necessarily lead to testing. Telit Communications S.p.A. recommends carrying out the following assessments: RF spectrum use (R&TTE art. 3.2) It will depend on the antenna used on the final product. EMC (R&TTE art. 3.1b) Testing Health & Safety (R&TTE art. 3.1a) Testing Alternately, assessment of the final product against EMC (Art. 3.1b) and Electrical safety (Art. 3.1a) essential requirements can be done against the essential requirements of the EMC and the LVD Directives: * Low Voltage Directive 2006/95/EC and product safety * Directive EMC 2004/108/EC for conformity for EMC Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 41 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 14.2. FCC/IC Regulatory notices (HE910) Modification statement Telit has not approved any changes or modifications to this device by the user. Any changes or modifications could void the user's authority to operate the equipment. Telit n'approuve aucune modification apportee a l'appareil par l'utilisateur, quelle qu'en soit la nature. Tout changement ou modification peuvent annuler le droit d'utilisation de l'appareil par l'utilisateur. Interference statement This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement. Wireless notice This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. The antenna should be installed and operated with minimum distance of 20 cm between the radiator and your body. Antenna gain must be below: Frequency band GSM 850/FDD V PCS 1900/FDD II FDD IV HE910, HE910-D 5.22 dBi 3.31 dBi 6.45 dBi This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 42 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 Cet appareil est conforme aux limites d'exposition aux rayonnements de la IC pour un environnement non controle. L'antenne doit etre installe de facon a garder une distance minimale de 20 centimetres entre la source de rayonnements et votre corps. Gain de l'antenne doit etre ci-dessous: Bande de frequence GSM 850/FDD V PCS 1900/FDD II FDD IV HE910, HE910-D 5.22 dBi 3.31 dBi 6.45 dBi L'emetteur ne doit pas etre colocalise ni fonctionner conjointement avec a autre antenne ou autre emetteur. FCC Class B digital device notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 43 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 14.3. 1999/5/EC Directive (LE910) The LE910-EUG module has been evaluated against the essential requirements of the 1999/5/EC Directive. Bulgarian Czech Danish Dutch English Estonian German Greek Hungarian Finnish French Icelandic Italian Latvian Lithuanian Telit Communications S.p.A. , 2G/3G/LTE module 1999/5/. Telit Communications S.p.A. timto prohlauje, e tento 2G/3G/LTE module je ve shod se zakladnimi poadavky a dalimi pislunymi ustanovenimi smrnice 1999/5/ES. Undertegnede Telit Communications S.p.A. erklaerer herved, at folgende udstyr 2G/3G/LTE module overholder de vaesentlige krav og ovrige relevante krav i direktiv 1999/5/EF. Hierbij verklaart Telit Communications S.p.A. dat het toestel 2G/3G/LTE module in overeenstemming is met de essentiele eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Hereby, Telit Communications S.p.A., declares that this 2G/3G/LTE module is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Kaesolevaga kinnitab Telit Communications S.p.A. seadme 2G/3G/LTE module vastavust direktiivi 1999/5/EU pohinouetele ja nimetatud direktiivist tulenevatele teistele asjakohastele satetele. Hiermit erklart Telit Communications S.p.A., dass sich das Gerat 2G/3G/LTE module in Ubereinstimmung mit den grundlegenden Anforderungen und den ubrigen einschlagigen Bestimmungen der Richtlinie 1999/5/EG befindet. Telit Communications S.p.A. 2G/3G/LTE module 1999/5/. Alulirott, Telit Communications S.p.A. nyilatkozom, hogy a 2G/3G/LTE module megfelel a vonatkozo alapveto kovetelmenyeknek es az 1999/5/EC iranyelv egyeb eloirasainak. Telit Communications S.p.A. vakuuttaa taten etta 2G/3G/LTE module tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sita koskevien direktiivin muiden ehtojen mukainen. Par la presente Telit Communications S.p.A. declare que l'appareil 2G/3G/LTE module est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Her me lysir Telit Communications S.p.A. yfir vi a 2G/3G/LTE module er i samraemi vi grunnkrofur og arar krofur, sem gerar eru i tilskipun 1999/5/EC Con la presente Telit Communications S.p.A. dichiara che questo 2G/3G/LTE module e conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Ar o Telit Communications S.p.A. deklar, ka 2G/3G/LTE module atbilst Direktvas 1999/5/EK btiskajm prasbm un citiem ar to saisttajiem noteikumiem. Siuo Telit Communications S.p.A. deklaruoja, kad is 2G/3G/LTE module atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 44 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 Maltese Hawnhekk, Telit Communications S.p.A., jiddikjara li dan 2G/3G/LTE module jikkonforma mal-tiijiet essenzjali u ma provvedimenti orajn relevanti li hemm fidDirrettiva 1999/5/EC. Norwegian Telit Communications S.p.A. erklaerer herved at utstyret 2G/3G/LTE module er i samsvar med de grunnleggende krav og ovrige relevante krav i direktiv 1999/5/EF. Polish Niniejszym Telit Communications S.p.A. owiadcza, e 2G/3G/LTE module jest zgodny z zasadniczymi wymogami oraz pozostaymi stosownymi postanowieniami Dyrektywy 1999/5/EC Portuguese Telit Communications S.p.A. declara que este 2G/3G/LTE module esta conforme com os requisitos essenciais e outras disposicoes da Directiva 1999/5/CE. Slovak Telit Communications S.p.A. tymto vyhlasuje, e 2G/3G/LTE module spa zakladne poiadavky a vetky prislune ustanovenia Smernice 1999/5/ES. Slovenian Telit Communications S.p.A. izjavlja, da je ta 2G/3G/LTE module v skladu z bistvenimi zahtevami in ostalimi relevantnimi doloili direktive 1999/5/ES. Spanish Por medio de la presente Telit Communications S.p.A. declara que el 2G/3G/LTE module cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Swedish Harmed intygar Telit Communications S.p.A. att denna 2G/3G/LTE module star I overensstammelse med de vasentliga egenskapskrav och ovriga relevanta bestammelser som framgar av direktiv 1999/5/EG. In order to satisfy the essential requirements of 1999/5/EC Directive, the LE910-EUG module is compliant with the following standards: RF spectrum use (R&TTE art. 3.2) EN 300 440-2 V1.4.1 EN 301 511 V9.0.2 EN 301 908-1 V6.2.1 EN 301 908-2 V6.2.1 EN 301 908-13 V6.2.1 EMC (R&TTE art. 3.1b) EN 301 489-1 V1.9.2 EN 301 489-3 V1.4.1 EN 301 489-7 V1.3.1 EN 301 489-24 V1.5.1 Health & Safety (R&TTE art. 3.1a) EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + AC:2011 EN 62311:2008 EN 62479:2010 The conformity assessment procedure referred to in Article 10 and detailed in Annex IV of Directive 1999/5/EC has been followed with the involvement of the following Notified Body: AT4 wireless, S.A. Parque Tecnologico de Andalucia C/ Severo Ochoa 2 29590 Campanillas - Malaga SPAIN Notified Body No: 1909 Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 45 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 Thus, the following marking is included in the product: The full declaration of conformity can be found on the following address: http://www.telit.com/ There is no restriction for the commercialisation of the LE910-EUG modules in all the countries of the European Union. Final product integrating this module must be assessed against essential requirements of the 1999/5/EC (R&TTE) Directive. It should be noted that assessment does not necessarily lead to testing. Telit Communications S.p.A. recommends carrying out the following assessments: RF spectrum use (R&TTE art. 3.2) It will depend on the antenna used on the final product. EMC (R&TTE art. 3.1b) Health & Safety (R&TTE art. 3.1a) Testing Testing Alternately, assessment of the final product against EMC (Art. 3.1b) and Electrical safety (Art. 3.1a) essential requirements can be done against the essential requirements of the EMC and the LVD Directives: * Low Voltage Directive 2006/95/EC and product safety * Directive EMC 2004/108/EC for conformity for EMC Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 46 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 14.4. FCC/IC Regulatory notices (LE910) Modification statement Telit has not approved any changes or modifications to this device by the user. Any changes or modifications could void the user's authority to operate the equipment. Telit n'approuve aucune modification apportee a l'appareil par l'utilisateur, quelle qu'en soit la nature. Tout changement ou modification peuvent annuler le droit d'utilisation de l'appareil par l'utilisateur. Interference statement This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement. Wireless notice This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. The antenna should be installed and operated with minimum distance of 20 cm between the radiator and your body. Antenna gain must be below: Frequency band LE910-NAG LE910-NVG LE910-SVG 700 MHz 850 MHz 1700 MHz 1900 MHz 8.74 dBi 6.93 dBi 5.00 dBi 2.51 dBi 9.16 dBi 9.42 dBi 5.00 dBi 8.01 dBi 6.93 dBi N/A 5.00 dBi N/A This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 47 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 Cet appareil est conforme aux limites d'exposition aux rayonnements de la IC pour un environnement non controle. L'antenne doit etre installe de facon a garder une distance minimale de 20 centimetres entre la source de rayonnements et votre corps. Gain de l'antenne doit etre ci-dessous: Bande de frequence 700 MHz 850 MHz 1700 MHz 1900 MHz LE910-NAG 8.74 dBi 6.93 dBi 5.00 dBi 2.51 dBi LE910-NVG 9.16 dBi 9.42 dBi 5.00 dBi 8.01 dBi LE910-SVG 6.93 dBi N/A 5.00 dBi N/A L'emetteur ne doit pas etre colocalise ni fonctionner conjointement avec a autre antenne ou autre emetteur. FCC Class B digital device notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Labelling Requirements for the Host device The host device shall be properly labelled to identify the modules within the host device. The certification label of the module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labelled to display the FCC ID and IC of the module, preceded by the words "Contains transmitter module", or the word "Contains", or similar wording expressing the same meaning, as follows: LE910-NAG Contains FCC ID: RI7LE910NA Contains IC: 5131A-LE910NA LE910-NVG Contains FCC ID: RI7LE910NV Contains IC: 5131A-LE910NV LE910-SVG Contains FCC ID: RI7LE910SV Contains IC: 5131A-LE910SV Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 48 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 L'appareil hote doit etre etiquete comme il faut pour permettre l'identification des modules qui s'y trouvent. L'etiquette de certification du module donne doit etre posee sur l'appareil hote a un endroit bien en vue en tout temps. En l'absence d'etiquette, l'appareil hote doit porter une etiquette donnant le FCC ID et le IC du module, precede des mots Contient un module d'emission , du mot Contient ou d'une formulation similaire exprimant le meme sens, comme suit : LE910-NAG Contains FCC ID: RI7LE910NA Contains IC: 5131A-LE910NA LE910-NVG Contains FCC ID: RI7LE910NV Contains IC: 5131A-LE910NV LE910-SVG Contains FCC ID: RI7LE910SV Contains IC: 5131A-LE910SV CAN ICES-3 (B) / NMB-3 (B) This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numerique de classe B est conforme a la norme canadienne ICES-003. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 49 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 14.5. Conformity Assessment Issues / Problemes d'evaluation de conformite (DE910) The DE910 is FCC/IC Approved as a module to be installed in other devices. This device should be used only for fixed and mobile applications and if the final product after integration is intended for portable use, a new application and FCC is required. Le DE910 est approuve FCC/IC comme module a installer dans d'autres dispositifs. Ce dispositif doit etre utilise uniquement pour des applications fixes et mobiles et si le produit fini est prevu apres integration pour un usage portatif, une nouvelle application et la FCC est requise The user is cautioned that this device should be used only as specified within this manual to meet RF exposure requirements. L'utilisateur est averti que ce dispositif doit etre utilise uniquement comme specifie dans ce manuel pour repondre aux normes d'exposition aux ondes rf. Use of this device in a manner inconsistent with this manual could lead to excessive RF exposure conditions. L'utilisation de ce dispositif en quelque sorte contradictoire avec ce manuel a pu mener aux etats excessifs d'exposition de rf. The DE910 conforms to the following US Directives: * Use of RF Spectrum. Standards: FCC47 Part 22&24 * EMC Standards: FCC47 Part 15 Le DE910 est conforme aux directives suivantes des USA * Utilisation de spectre de rf. Normes : FCC47 partie 22&24 * Normes d'EMC : FCC47 partie 15 This device complies with Part 15 of the FCC Rules. Ce dispositif est conforme a la partie 15 des regles FCC. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le fonctionnement est sujet aux deux conditions suivantes : (1) ce dispositif peut ne pas causer l'interference nocive, et (2) ce dispositif doit accepter aucune interference, y compris un interference qui pourrait causer le fonctionnement non desire du dispositif. The user must refer to below information to meet the FCC/IC's RF exposure rules and regulations when they design: Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 50 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 Lors de la conception, l'utilisateur doit se referer a l'information ci-dessous pour remplir les conditions et reglementations FCC/IC' d'exposition aux ondes RF: * * * * * * * The system antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all the persons and must not be colocated or operating in conjunction with any other antenna or transmitter. Le systeme d'antenne utilise pour cet emetteur doit etre installe a une distance d'au moins de 20 cm de toute personne et ne doit pas etre co-implante ou operer en meme temps que n'importe quelle autre antenne ou emetteur. The system antenna(s) used for this module must not exceed 5.12dBi in CDMA BC0 and 6.12dBi in CDMA BC1 for mobile and fixed or mobile operating configurations. Le systeme d' antenne utilise pour ce module ne doit pas depasser 5.12dBi en CDMA BC0 et 6.12dBi en CDMA BC1 pour des configurations mobiles et fixes ou des configurations operant en mode mobile. Users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Manufacturers of mobile, fixed or portable devices incorporating this module are advised to clarify any regulatory questions and to have their complete product tested and approved for FCC compliance. Les instructions d'installation de l'antenne ainsi que les conditions de fonctionnement de l'emetteur doivent etre remis aux utilisateurs et aux installateurs conformement a la reglementation sur l'exposition aux ondes rf. Des fabricants des dispositifs mobiles, fixes ou portables incorporant ce module sont invites a clarifier toutes les questions de normalisation et a avoir leur produit completement teste pour la mise en conformite FCC. DE910 is intended for the OEM integrator only. DE910 est prevu pour l'integrateur OEM seulement. The user is required to see the Grant of Equipment document for other restrictions. L'utilisateur doit se referrer au document Grant of equipment pour d'autres restrictions. DE910 must be operated and used with a locally approved access point. DE910 doit etre actionne et utilise avec un point d'acces localement approuve. The radio transmitter(IC ID: 5131A-DE910DUAL) has been approved by Industry Canada to operate with the antenna type listed in this manual with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. L'emetteur radio (identification d'IC : 5131A-DE910DUAL) a ete approuve par Industry Canada pour fonctionner avec le type d'antenne enumere dans ce manuel avec le gain autorise maximum et l'impedance d'antenne exigee pour chaque type d'antenne indique. Les types d'antenne non inclus dans cette liste, ayant un gain superieur au gain maximum indique pour ce type, sont strictement interdits pour un usage avec ce dispositif. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 51 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 The following regulatory and safety notices must be published in documentation supplied to the end user of the product or system incorporating an adapter in compliance with local regulations. * Host system including DE910 must be labeled with "Contains transmitter module with FCC ID: RI7DE910-DUAL and IC ID: 5131A-DE910DUAL" Les notices de normalisation et de securite doivent se trouver dans la documentation fournie a l'utilisateur du produit ou du systeme incorporant un adaptateur conforme aux reglementations locales. * Le systeme hote comprenant DE910 doit etre marque avec Contient un module emetteur avec IDENTIFICATION FCC : RI7DE910-DUAL et identification IC : 5131A-DE910DUAL 14.6. CONFORMITY ASSESSMENT ISSUES (LE910 V2) 14.6.1. FCC/IC Regulatory notices Modification statement Telit has not approved any changes or modifications to this device by the user. Any changes or modifications could void the user's authority to operate the equipment. Telit n'approuve aucune modification apportee a l'appareil par l'utilisateur, quelle qu'en soit la nature. Tout changement ou modification peuvent annuler le droit d'utilisation de l'appareil par l'utilisateur. Interference statement This device complies with Part 15 of the FCC Rules and Industry Canada licenceexempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 52 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 Cet appareil est conforme aux limites d'exposition aux rayonnements de la IC pour un environnement non controle. L'antenne doit etre installe de facon a garder une distance minimale de 20 centimetres entre la source de rayonnements et votre corps. Gain de l'antenne doit etre ci-dessous: RF exposure This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. The antenna should be installed and operated with minimum distance of 20 cm between the radiator and your body. Antenna gain must be below: Antenna Gain Frequency Band LE910-NA V2 LE910-SV V2 700 MHz 6.63 dBi 6.94 dBi 850 MHz 6.63 dBi N/A 1700 MHz 6.00 dBi 6.00 dBi 1900 MHz 8.51 dBi 9.01 dBi Cet appareil est conforme aux limites d'exposition aux rayonnements de la IC pour un environnement non controle. L'antenne doit etre installe de facon a garder une distance minimale de 20 centimetres entre la source de rayonnements et votre corps. Gain de l'antenne doit etre ci-dessous: Gain de l`antenne Bande de frequence LE910-NA V2 LE910-SV V2 700 MHz 6.63 dBi 6.94 dBi 850 MHz 6.63 dBi N/A 1700 MHz 6.00 dBi 6.00 dBi Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 53 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 1900 MHz 8.51 dBi 9.01 dBi L'emetteur ne doit pas etre colocalise ni fonctionner conjointement avec a autre antenne ou autre emetteur. FCC Class B digital device notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: * Reorient or relocate the receiving antenna. * Increase the separation between the equipment and receiver. * Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. * Consult the dealer or an experienced radio/TV technician for help. Labelling Requirements for the Host device The host device shall be properly labelled to identify the modules within the host device. The certification label of the module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labelled to display the FCC ID and IC of the module, preceded by the words "Contains transmitter module", or the word "Contains", or similar wording expressing the same meaning, as follows: LE910-NA V2 Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 54 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 Contains FCC ID: RI7LE910NAV2 Contains IC: 5131A-LE910NAV2 LE910-SV V2 Contains FCC ID: RI7LE910SVV2 Contains IC: 5131A-LE910SVV2 L'appareil hote doit etre etiquete comme il faut pour permettre l'identification des modules qui s'y trouvent. L'etiquette de certification du module donne doit etre posee sur l'appareil hote a un endroit bien en vue en tout temps. En l'absence d'etiquette, l'appareil hote doit porter une etiquette donnant le FCC ID et le IC du module, precede des mots Contient un module d'emission , du mot Contient ou d'une formulation similaire exprimant le meme sens, comme suit : LE910-NA V2 Contains FCC ID: RI7LE910NAV2 Contains IC: 5131A-LE910NAV2 LE910-SV V2 Contains FCC ID: RI7LE910SVV2 Contains IC: 5131A-LE910SVV2 CAN ICES-3 (B) / NMB-3 (B) This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numerique de classe B est conforme a la norme canadienne ICES-003. 14.7. Safety Recommendations (LE910 V2) Be sure the use of this product is allowed in the country and in the environment required. The use of this product may be dangerous and has to be avoided in the following areas: Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 55 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 * Where it can interfere with other electronic devices in environments such as hospitals, airports, aircrafts, etc. * Where there is risk of explosion such as gasoline stations, oil refineries, etc. It is responsibility of the user to enforce the country regulation and the specific environment regulation. Do not disassemble the product; any mark of tampering will compromise the warranty validity. We recommend following the instructions of the hardware user guides for a correct wiring of the product. The product has to be supplied with a stabilized voltage source and the wiring has to be conforming to the security and fire prevention regulations. The product has to be handled with care, avoiding any contact with the pins because electrostatic discharges may damage the product itself. Same cautions have to be taken for the SIM, checking carefully the instruction for its use. Do not insert or remove the SIM when the product is in power saving mode. The system integrator is responsible of the functioning of the final product; therefore, care has to be taken to the external components of the module, as well as of any project or installation issue, because the risk of disturbing the GSM network or external devices or having impact on the security. Should there be any doubt, please refer to the technical documentation and the regulations in force. Every module has to be equipped with a proper antenna with specific characteristics. The antenna has to be installed with care in order to avoid any interference with other electronic devices and has to guarantee a minimum distance from the body (20 cm). In case of this requirement cannot be satisfied, the system integrator has to assess the final product against the SAR regulation. The European Community provides some Directives for the electronic equipment introduced on the market. All the relevant information's are available on the European Community website: http://ec.europa.eu/enterprise/sectors/rtte/documents/ The text of the Directive 99/05 regarding telecommunication equipment is available, while the applicable Directives (Low Voltage and EMC) are available at: Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 56 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 http://ec.europa.eu/enterprise/sectors/electrical/ 14.8. Safety Recommendations (HE910) The device must be supplied with a limited power source that meets clause 2.5 of the EN 60950-1 standard. This requirements are: For power supplies without overcurrent protection device----> Shortcircuit current < 8 A. / Apparent power < 100 VA For power supplies with overcurrent protection device (rated current of overcurrent device shall be < 5A) --- > Shortcircuit current < 333 A. / Apparent power < 250 VA. Furthermore, the device must be installed within an enclosure that meets HB class or pass the 550 glowing fire test of EN 60695-2-11. 14.9. Safety Recommendations (DE910) READ CAREFULLY Be sure the use of this product is allowed in the country and in the environment required. The use of this product may be dangerous and has to be avoided in the following areas: * Where it can interfere with other electronic devices in environments such as hospitals, airports, aircrafts, etc. * Where there is risk of explosion such as gasoline stations, oil refineries, etc. It is the responsibility of the user to enforce the country's regulations and the specific environmental regulation. Do not disassemble the product; any evidence of tampering will compromise the warranty validity. Follow the instructions of the hardware user guides for a correct wiring of the product. The product has to be supplied with a stabilized voltage source and the wiring has to conform to the security and fire prevention regulations. The product has to be handled with care, avoiding any contact with the pads because electrostatic discharges may damage the product itself. The system integrator is responsible for the functioning of the final product; therefore, care has to be taken with the external components of the module as well as of any project or installation issue because of the risk of disturbing the CDMA network or external devices or having impact on security. Should there be any doubt, please refer to the technical documentation and the regulations in force. Every module has to be equipped with a proper antenna with specific characteristics. The antenna has to be installed with care in order to avoid any interference with other electronic devices and has to guarantee a minimum distance from the body (20 cm). In case this requirement cannot be satisfied, the system integrator has to assess the final product against SAR regulations. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 57 of 58 xE910 Mini PCIe Hardware User Guide 1vv0301006 Rev.11 - 2017-05-15 15. Document History Revision ISSUE#0 ISSUE#1 Date 2012-05-08 2012-27-07 ISSUE#2 ISSUE#3 2012-25-09 2012-11-22 ISSUE#4 ISSUE#5 ISSUE#6 ISSUE #7 2013-08-22 2014-04-08 2014-05-16 2014-08-06 ISSUE #8 ISSUE#9 2014-10-20 2015-02-03 ISSUE#10 ISSUE #11 2015-06-12 2017-05-15 Changes First issue 3.1 PINOUT updated 9 Wake functionality and new example 10 Audio section added 11 Mechanical layout drawing changed Minor grammatical corrections Minor grammatical corrections. 4.2 peak current requirement raised to 2.4A 5 sensitivity and output power (modify) 8 SH note added. Capacitor on SIMVCC changed from 1uF to 100 nF. 11 new drawing Added chapters 5.3.1, 5.3.2, 11.1, 11.2 Temperature Range modified Updated chapter 11.2 Updated chapter 11 Added LE910 and DE910 Updated document's tables Chapter 5.5.2 updated Chapter 14 updated; added 14.6 Safety Recommendations on HE910 Added LE910 V2 across the document Adding new models JN1, NA1, SV1 Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 58 of 58