C-13-622-T-SSC4E - Source Photonics, Inc.

622 Mbps Single Mode Transceiver

C-13-622(C)-T(3)-SSC4

20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486

9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213

LUMINENTOIC.COM LUMNDS111-Jul1106

Rev A.1

Parameter Symbol Min Typical Max Unit Notes

Optical

Optical Transmit Power Po-3 - +2 dBm

Output center Wavelength λp1296 1310 1330 nm 25ºC

Output Spectrum Width ∆λrms - - 2.5 nm RMS(σ)

Extinction Ratio ER 8.2 - - dB

Output Eye Compliant with ITU-T G.957/STM-4 Eye Mask

Optical Rise Time tr- - 1.2 ns 10% to 90% Values

Optical Fall Time tf- - 1.2 ns 10% to 90% Values

Relative Intensity Noise RIN - - -120 dB/Hz

Total Jitter TJ - - 0.55 ns Measured with 223-1 PRBS with 72 ones and

72 zeros.

Transmitter Speciﬁcations

Features

• SC Duplex Single Mode Transceiver

• Industry Standard 1x9 Footprint

• Complies with SONET OC-12 SDH STM-4

• Single +3.3V/+5V Power Supply

• OperatingTemperature Range: 0 to 70ºC and -40 to 85ºC

• PECL Differential Inputs and Outputs

• PECL/LVPECL Signal Detection Output [C-13-622-T(3)-SSC4]

• TTL/LVTTL Signal Detection Output [C-13-622C-T(3)-SSC4]

• Wave Solderable and Aqueous Washable

• Uncooled laser diode with MQW structure

• Complies with Telcordia (Bellcore) GR-468-CORE

• SONET OC-12 Application

• RoHS compliance available

Parameter Symbol Min. Max. Unit Note

Power Supply Voltage Vcc 0 6 V C-13-622(C)-T-SSC4

Power Supply Voltage Vcc 0 3.6 V C-13-622(C)-T3-SSC4

Output Current Iout 0 30 mA

Soldering Temperature -- 260 ºC 10 seconds on leads only

Storage Temperature Tstg -40 85 ºC

Absolute Maximum Rating

Parameter Symbol Min. Typ. Max. Unit Note

Power Supply Voltage Vcc 4.75 5 5.25 V C-13-622(C)-T-SSC4

Power Supply Voltage Vcc 3.1 3.3 3.5 V C-13-622(C)-T3-SSC4

Operating Temperature (Case) Topr 0 - 70 ºC C-13-622(C)-T(3)-SSC4(D/E)

Operating Temperature (Case) Topr -40 - 85 ºC C-13-622(C)-T(3)-SSC4A(B/C)

Data Rate - - 622 - Mbps

Recommended Operating Condition

622 Mbps Single Mode Transceiver

C-13-622(C)-T(3)-SSC4

20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486

9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213

LUMINENTOIC.COM LUMNDS111-Jul1106

Rev A.1

Parameter Symbol Min Typical Max Unit Notes

Electrical

Power Supply Current ICC - - 180 mA Maximum current is speciﬁed at Vcc=

Maximum @ maximum temperature

Data Input Current-Low IIL -350 - - µA

Data Input Current-High IIH - - 350 µA

Differential Input Voltage VIH-VIL 300 - - mV

Data Input Voltage-Low VIL-VCC -2.0 - -1.58 V These inputs are compatible with 10K, 10KH

and 100K ECL and PECL inputs

Data Input Voltage-High VIH-VCC -1.1 - -0.74 V

Transmitter Speciﬁcations

Parameter Symbol Min Typical Max Unit Notes

Optical

Sensitivity - - - -28 dBm Measured with 223-1 PRBS,BER= 10-10

Maximum Input Power Pin -3 - - dBm

Signal Detect-Asserted Pa - - -28 dBm Measured on transition: low to high

Signal Detect-Deasserted Pd -40 - - dBm Measured on transition: high to low

Signal Detect-Hysteresis 1 - 5 dB

Wavelength of Operation 1100 - 1600 nm

Receiver Speciﬁcations

Parameter Symbol Min Typical Max Unit Note

Electrical

Power Supply Current ICC - - 100 mA The current excludes the output load current

Data output Voltage-Low VOL -Vcc -2 - -1.58 V These outputs are compatible with 10K,

10KH and 100KECL and LVPECL outputs

Data Output Voltage-High VOH- Vcc -1.1 - -0.74 V

Signal Detect Output Voltage-Low VSDL - - 0.5 V C-13-622C-T(3)-SSC4

Signal Detect Output Voltage-High VSDH 2.0 - -

Signal Detect Output Voltage-Low VSDL-Vcc -2.0 - -1.58 V C-13-622-T(3)-SSC4

Signal Detect Output Voltage-High VSDH- Vcc -1.1 - -0.74 V

Receiver Speciﬁcations

622 Mbps Single Mode Transceiver

C-13-622(C)-T(3)-SSC4

20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486

9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213

LUMINENTOIC.COM LUMNDS111-Jul1106

Rev A.1

Warnings

Connection Diagram

1. (Rx GND)

2. (Rx +) NC

3. (Rx-)

4. (SD)

5. (Rx Vcc) Top View

6. (Tx Vcc)

7. (TX-) NC

8. (TX+)

9. (Tx GND)

Receiver Signal Ground

Receiver Data Out

Receiver Data Out Bar

Signal Detect

Receiver Power Supply

Transmitter Power Supply

Transmitter Data In Bar

Transmitter Data in

Transmitter Signal Ground

PIN Symbol Notes

1RxGND Directly connect this pin to the receiver ground plane

2 RD+ See recommended circuit schematic

3 RD- See recommended circuit schematic

4 SD Active high on this indicates a received optical signal

5 RxVcc +3.3V/5V dc power for the receiver section

6 TxVcc +3.3V/5V dc power for the transmitter section

7 TD- See recommended circuit schematic

8 TD+ See recommended circuit schematic

9 TxGND Directly connect this pin to the transmitter ground plane

622 Mbps Single Mode Transceiver

C-13-622(C)-T(3)-SSC4

20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486

9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213

LUMINENTOIC.COM LUMNDS111-Jul1106

Rev A.1

123

8 6

Rx Vcc

Tx Vcc

Transceiver

Top view

No internal

connection

No internal

connection

Rx Vcc

Tx Vcc

Vcc

Tx Vcc Rx Vcc

RD +

RD -

TD +

TD -

R6 R8

R7 C6

C5 R1 R3

R2 R4

Notes +3.3V:

R1=R3=R5=R7=130

R2=R4=R6=R8=82

C1=C2=C3=C5=C6=0.1F

C4=10F

L1=L2=1H

Notes +5V:

R1=R3=R5=R7=82

R2=R4=R6=R8=130

C1=C2=C3=C5=C6=0.1F

C4=10F

L1=L2=1H

123

8 6

Rx Vcc

Tx Vcc

Transceiver

Top view

No internal

connection

No internal

connection

Rx Vcc

Tx Vcc

Vcc

Tx Vcc Rx Vcc

RD +

RD -

TD +

TD -

R10

R9 R7

C5 R1 R3

R2 R4

Notes +3.3V:

R1=R3=R5=R7=R9=130

R2=R4=R6=R8=R10=82

C1=C2=C3=C5=C6=0.1F

C4=10F

L1=L2=1H

Notes +5V:

R1=R3=R5=R7=R9=82

R2=R4=R6=R8=R10=130

C1=C2=C3=C5=C6=0.1F

C4=10F

L1=L2=1H

The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals.

The power supply ﬁltering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc.

A GND plane under the module is required for good EMI and sensitivity performance.

Recommended Circuit Schematic

C-13-622-T(3)-SSC4

C-13-622C-T(3)-SSC4

622 Mbps Single Mode Transceiver

C-13-622(C)-T(3)-SSC4

20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486

9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213

LUMINENTOIC.COM LUMNDS111-Jul1106

Rev A.1

Package Diagram (10.4 mm SC transceiver assembly)

Front View

SC Transceiver Assembly 10.4mm

Side View

Top View

Rear View

Package Diagram (9.8 mm SC transceiver assembly)

Side View Rear View

SC Transceiver Assembly 9.8mm

Top View Front View

Blank: Black case

A : Black case

C, D: Black case

B, E: Blue case

622 Mbps Single Mode Transceiver

C-13-622(C)-T(3)-SSC4

20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486

9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213

LUMINENTOIC.COM LUMNDS111-Jul1106

Rev A.1

• Communication protocol

(622 Mbps)

622 = PECL/LVPEC Signal Detection Output

622C =TTL/LVTTL Signal Detection Output

Ordering Information

C - 13 - 622(C) - T(3) - S SC TxPower Temperature and Package -RoHS

• Wavelength

13= 1310 nm

• Connector options

• +3.3V / 5V FP Transceiver

T = 5V transceiver

T3 = 3.3V transceiver

• Single mode ﬁber

• Temperature range and package

Blank = commercial temperature(0 to 70 ºC), 10.4 mm, Black case

A = industrial temperature(-40 to 85 ºC), 10.4 mm, Black case

B = industrial temperature(-40 to 85 ºC), 9.8 mm, Blue case

C = industrial temperature(-40 to 85 ºC), 9.8 mm, Black case

D = commercial temperature(0 to 70 ºC), 9.8 mm, Black case

E = commercial temperature(0 to 70 ºC), 9.8 mm, Blue case

Available Options:

C-13-622-T(3)-SSC4

C-13-622C-T(3)-SSC4

C-13-622-T(3)-SSC4-G5

C-13-622C-T(3)-SSC4-G5

C-13-622-T(3)-SSC4A

C-13-622C-T(3)-SSC4A

C-13-622-T(3)-SSC4A-G5

C-13-622C-T(3)-SSC4A-G5

Part unmbering Deﬁnition:

C-13-622-T(3)-SSC4B

C-13-622C-T(3)-SSC4B

C-13-622-T(3)-SSC4B-G5

C-13-622C-T(3)-SSC4B-G5

C-13-622-T(3)-SSC4C

C-13-622C-T(3)-SSC4C

C-13-622-T(3)-SSC4C-G5

C-13-622C-T(3)-SSC4C-G5

C-13-622-T(3)-SSC4D

C-13-622C-T(3)-SSC4D

C-13-622-T(3)-SSC4D-G5

C-13-622C-T(3)-SSC4D-G5

C-13-622-T(3)-SSC4E

C-13-622C-T(3)-SSC4E

C-13-622-T(3)-SSC4E-G5

C-13-622C-T(3)-SSC4E-G5

• Tx Power range

4 = -3 to +2 dBm

• Ordering Information

Blank = RoHS non-compliant product

G5 = RoHS 5/6-compliant product (lead exemption)

622 Mbps Single Mode Transceiver

C-13-622(C)-T(3)-SSC4

20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486

9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 LUMNDS111-Jul1106

Rev A.1

LUMINENTOIC.COM

IMPORTANT NOTICE!

All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance

of its products to current speciﬁcations only in accordance with the company’s standard one-year warranty; however, speciﬁcations designated as “preliminary” are

given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warran-

ties, warranties of merchantability, ﬁtness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of

Sale for further warranty information.

LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual

property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes

no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this docu-

ment are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers

using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from

such use or sale.

THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any

actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact

LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current.

Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow

guidelines according to proper ESD procedures.

Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation.

Warnings:

Legal Notes: