Data Sheet 3-TERMINAL POSITIVE LINEAR REGULATOR AZ78LXX General Description Features The AZ78LXX series are three terminal positive regulators with several fixed output voltages. These regulators can provide local on card regulation, eliminating the distribution problems associated with single point regulation. The AZ78LXX can be used in logic systems, instrumentation, HiFi, and other solid state electronic equipment. When used as a Zener diode/resistor combination replacement, the AZ78LXX usually results an effective output impedance improvement of two orders of magnitude, and lower quiescent current. * * * * * * Output Current up to 100mA Fixed Output Voltages of 5V, 8V, 9V and 12V Output Voltage Tolerances of 5% over the Full Temperature Range Internal Short Circuit Current-limiting Internal Thermal Overload Protection No External Components Applications With adequate heat sinking the AZ78LXX can deliver 100mA output current. Current limiting is included to limit the peak output current to a safe value. Thermal protection is also provided. If internal power dissipation becomes too high for the heat sinking provided, the thermal shutdown circuit takes over preventing the IC from overheating. * * * * High Efficiency Linear Regulator Post Regulation for Switching Supply Microprocessor Power Supply Mother Board I/O Power Supply The AZ78LXX are available in the plastic TO-92 (bulk or ammo packing), SOT-223 and SOT-89 packages. TO-92(Bulk Packing) TO-92(Ammo Packing) SOT-89 SOT-223 Figure 1. Package Types of the AZ78LXX Nov. 2012 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 1 Data Sheet 3-TERMINAL POSITIVE LINEAR REGULATOR AZ78LXX Pin Configuration Z Package (TO-92(Ammo Packing)) Z Package (TO-92(Bulk Packing)) 3 INPUT GND 2 GND OUTPUT 1 OUTPUT 3 INPUT 2 1 R Package (SOT-89) H Package (SOT-223) GND 4 3 INPUT 2 GND 1 OUTPUT GND 4 3 INPUT 2 GND 1 OUTPUT Connect pin 4 to pin 2 or leave pin 4 electrically isolated Figure 2. Pin Configuration of the AZ78LXX (Top View) Nov. 2012 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 2 Data Sheet 3-TERMINAL POSITIVE LINEAR REGULATOR AZ78LXX Functional Block Diagram 3 (8) 1 INPUT OUTPUT A(B) A for 3-pin B for 8-pin 2, 4 (2, 3, 6, 7) GND Figure 3. Functional Block Diagram of the AZ78LXX Nov. 2012 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 3 Data Sheet 3-TERMINAL POSITIVE LINEAR REGULATOR AZ78LXX Ordering Information - AZ78L E1: Lead Free G1: Green Circuit Type TR: Tape and Reel or Ammo Blank: Tube or Bulk Output Voltage 05: 5V 08: 8V 09: 9V 12: 12V Package TO-92 SOT-89 SOT-223 Temperature Range -40 to 125oC -40 to 125oC -40 to 125oC Package Z: TO-92 R: SOT-89 H: SOT-223 Part Number Lead Free Marking ID Green Lead Free Green Packing Type AZ78L05Z-E1 AZ78L05Z-G1 AZ78L05Z-E1 AZ78L05Z-G1 Bulk AZ78L05ZTR-E1 AZ78L05ZTR-G1 AZ78L05Z-E1 AZ78L05Z-G1 Ammo AZ78L08Z-E1 AZ78L08Z-G1 AZ78L08Z-E1 AZ78L08Z-G1 Bulk AZ78L08ZTR-E1 AZ78L08ZTR-G1 AZ78L08Z-E1 AZ78L08Z-G1 Ammo AZ78L09Z-E1 AZ78L09Z-G1 AZ78L09Z-E1 AZ78L09Z-G1 Bulk AZ78L09ZTR-E1 AZ78L09ZTR-G1 AZ78L09Z-E1 AZ78L09Z-G1 Ammo AZ78L12Z-E1 AZ78L12Z-G1 AZ78L12Z-E1 AZ78L12Z-G1 Bulk AZ78L12ZTR-E1 AZ78L12ZTR-G1 AZ78L12Z-E1 AZ78L12Z-G1 Ammo AZ78L05RTR-E1 AZ78L05RTR-G1 E78A G78A Tape & Reel AZ78L08RTR-E1 AZ78L08RTR-G1 E78B G78B Tape & Reel AZ78L09RTR-E1 AZ78L09RTR-G1 E78C G78C Tape & Reel AZ78L12RTR-E1 AZ78L12RTR-G1 E78D G78D Tape & Reel AZ78L05HTR-E1 AZ78L05HTR-G1 EH78A GH78A Tape & Reel AZ78L08HTR-E1 AZ78L08HTR-G1 EH78B GH78B Tape & Reel AZ78L09HTR-E1 AZ78L09HTR-G1 EH78C GH78C Tape & Reel AZ78L12HTR-E1 AZ78L12HTR-G1 EH78D GH78D Tape & Reel BCD Semiconductor's Pb-free products, as designated with "E1" suffix in the part number, are RoHS compliant. Products with "G1" suffix are available in green packages. Nov. 2012 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 4 Data Sheet 3-TERMINAL POSITIVE LINEAR REGULATOR AZ78LXX Absolute Maximum Ratings (Note 1) Parameter Input Voltage Operating Junction Temperature Lead Temperature (Soldering, 10sec) o Power Dissipation (TA=25 C) Symbol Value Unit VIN 20 V TJ 150 o TLEAD 260 oC PD TO-92 0.65 SOT-223 0.7 SOT-89 0.65 C W Storage Temperature Range TSTG -65 to 150 oC ESD (Human Body Model) ESD 2000 V ESD (Machine Model) ESD 200 V Note 1: Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "Recommended Operating Conditions" is not implied. Exposure to "Absolute Maximum Ratings" for extended periods may affect device reliability. Recommended Operating Conditions Parameter Symbol Min AZ78L05 Input Voltage Max Unit 15 AZ78L08 18 VIN AZ78L09 18 AZ78L12 18 Operating Junction Temperature TJ Nov. 2012 Rev. 2. 2 -40 125 V o C BCD Semiconductor Manufacturing Limited 5 Data Sheet 3-TERMINAL POSITIVE LINEAR REGULATOR AZ78LXX Electrical Characteristics AZ78L05 Electrical Characteristics Limits in standard typeface are for TJ=25oC, Bold typeface applies over -40oC to 125oC, IOUT=40mA, CIN =0.33F, COUT=0.1F, VIN=10V, unless otherwise specified. Parameter Output Voltage Symbol VOUT Conditions Min Typ Max 4.8 5 5.2 4.75 7.0V VIN 15V Unit 5.25 V 1.0mA IOUT 40mA (Note 2) Line Regulation VRLINE 7.0V VIN 15V 18 75 mV Load Regulation VRLOAD 1.0mA IOUT 100mA 20 60 mV Dropout Voltage VDROP Current Limit ILIMIT IQ Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Peak Output Current IQ NO PSRR 1.6 V TJ=25oC 150 mA IOUT=0 3 5 mA 8.0V VIN 15V 1.0 mA 1.0mA IOUT 40mA 0.1 10Hz f 100kHz (Note 3) f=120Hz, 8.0V VIN 15V 47 IPK Average Temperature Coefficient of VOUT/ T IOUT = 5.0mA Output Voltage Minimum Value of Input Voltage Required to Maintain Line Regulation Thermal Resistance VIN (Min) JC 40 V 62 dB 150 mA 0.65 mV/ oC 6.7 TO-92 81 SOT-89 29.8 SOT-223 71 7 V o C/W Note 2: Power Dissipation 0.6W Note 3: Recommended minimum load capacitance of 0.01F to limit high frequency noise. Nov. 2012 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 6 Data Sheet 3-TERMINAL POSITIVE LINEAR REGULATOR AZ78LXX Electrical Characteristics (Continued) AZ78L08 Electrical Characteristics Limits in standard typeface are for TJ=25oC, Bold typeface applies over -40oC to 125oC, IOUT=40mA, CIN =0.33F, COUT=0.1F, VIN=14V, unless otherwise specified. Parameter Symbol Output Voltage VOUT Line Regulation VRLINE Load Regulation VRLOAD Dropout Voltage VDROP Current Limit ILIMIT IQ Conditions Min Typ Max 7.7 8.0 8.3 7.6 11V VIN 18V Unit 8.4 V 1.0mA IOUT 40mA (Note Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Peak Output Current IQ 11V VIN 18V 18 75 mV 1.0mA IOUT 100mA 20 90 mV 1.6 V TJ=25oC 150 mA IOUT=0 3 5 mA 11V VIN 18V 1.5 mA 1.0mA IOUT 40mA 0.1 NO 10Hz f 100kHz (Note 3) PSRR f=120Hz, 11V VIN 18V IPK Average Temperature Coefficient of VOUT/ T IOUT= 5.0mA Output Voltage Minimum Value of Input Voltage Required to Maintain Line Regulation Thermal Resistance VIN (Min) JC V 60 39 45 dB 150 mA 0.8 mV/ oC 9.7 V TO-92 81 SOT-89 84 SOT-223 71 o C/W Note 2: Power Dissipation 0.6W Note 3: Recommended minimum load capacitance of 0.01F to limit high frequency noise. Nov. 2012 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 7 Data Sheet 3-TERMINAL POSITIVE LINEAR REGULATOR AZ78LXX Electrical Characteristics (Continued) AZ78L09 Electrical Characteristics Limits in standard typeface are for TJ=25oC, Bold typeface applies over -40oC to 125oC, IOUT=40mA, CIN =0.33F, COUT=0.1F, VIN =15V, unless otherwise specified. Parameter Output Voltage Symbol VOUT Conditions Min Typ Max 8.6 9 9.4 9.45 V 18 75 mV 20 90 mV 8.55 12V VIN 18V Unit 1.0mA IOUT 40mA (Note 2) Line Regulation VRLINE 12V VIN 18V 1.0mA IOUT 100mA Load Regulation VRLOAD Dropout Voltage VDROP Current Limit ILIMIT IQ Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Peak Output Current IQ 1.6 V TJ=25oC 150 mA IOUT=0 3 5 mA 12V VIN 18V 1.5 mA 1.0mA IOUT 40mA 0.1 NO 10Hz f 100kHz (Note 3) PSRR f=120Hz, 12V VIN 18V 38 IPK Average Temperature Coefficient of VOUT/ T IOUT= 5.0mA Output Voltage Minimum Value of Input Voltage Required to Maintain Line Regulation Thermal Resistance VIN (Min) JC 70 V 44 dB 150 mA 0.9 mV/ oC 10.7 V TO-92 81 SOT-89 84 SOT-223 71 o C/W Note 2: Power Dissipation 0.6W Note 3: Recommended minimum load capacitance of 0.01F to limit high frequency noise. Nov. 2012 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 8 Data Sheet 3-TERMINAL POSITIVE LINEAR REGULATOR AZ78LXX Electrical Characteristics (Continued) AZ78L12 Electrical Characteristics Limits in standard typeface are for TJ=25oC, Bold typeface applies over -40oC to 125oC, IOUT=40mA, CIN =0.33F, COUT=0.1F, VIN=18V, unless otherwise specified. Parameter Output Voltage Symbol VOUT Conditions Min Typ Max 11.5 12 12.5 11.4 15V VIN 18V Unit 12.6 V 1.0mA IOUT 40mA (Note 2) Line Regulation VRLINE 15V VIN 18V 18 75 mV Load Regulation VRLOAD 1.0mA IOUT 100mA 20 90 mV Dropout Voltage VDROP Current Limit ILIMIT IQ Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Peak Output Current IQ NO PSRR 1.6 V TJ=25oC 150 mA IOUT=0 3 5 mA 15V VIN 18V 1.5 mA 1.0mA IOUT 40mA 0.1 80 V 54 dB 150 mA 1.0 mV/ oC 13.7 V 10Hz f 100kHz (Note 3) f=120Hz, 15V VIN 18V IPK 40 Average Temperature Coefficient of VOUT/ T IOUT = 5.0mA Output Voltage Minimum Value of Input Voltage Required to Maintain Line Regulation Thermal Resistance VIN (Min) JC TO-92 81 SOT-89 84 SOT-223 71 o C/W Note 2: Power Dissipation 0.6W Note 3: Recommended minimum load capacitance of 0.01F to limit high frequency noise. Nov. 2012 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 9 Data Sheet 3-TERMINAL POSITIVE LINEAR REGULATOR AZ78LXX Typical Performance Characteristics 2.0 5 IOUT=40mA 3 IOUT=1mA 2 1.4 1.2 IOUT=1mA 1.0 0.8 0.6 1 AZ78L05 V=1%*VOUT 0.4 0.2 0 0 2 4 6 8 0.0 -40 10 -20 0 VI input voltage(V) (V) Input Voltage 20 40 60 80 100 120 o Junction Temperature ( C) Figure 4. Dropout Characteristics Figure 5. Dropout Voltage vs. Junction Temperature 3.0 3.0 AZ78L05 VIN=10V 2.9 2.5 IOUT=5mA 2.8 Input Bias Current (mA) Quiescent Current (mA) IOUT=100mA 1.6 IOUT=100mA TJ =25 oC Dropout Voltage (V) Output Voltage (V) 4 IOUT=40mA 1.8 AZ78L05 VOUT=5V 2.7 2.6 2.5 2.4 2.0 1.5 AZ78L05 VOUT=5.0V 1.0 IOUT=40mA o TJ=25 C 0.5 2.3 2.2 -40 0.0 -20 0 20 40 60 80 100 120 0 2 4 6 8 10 12 14 16 18 20 Input Voltage (V) o Junction Temperature ( C) Figure 6. Quiescent Current vs. Junction Temperature Figure 7. Input Bias Current vs. Input Voltage Nov. 2012 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 10 Data Sheet 3-TERMINAL POSITIVE LINEAR REGULATOR AZ78LXX Typical Performance Characteristics (Continued) 75 11 IOUT (25mA/Div) AZ78L05 10.5 10 VOUT (100mV/Div) VOUT (20mV/Div) VIN (0.5V/Div) 11.5 20 0 -20 AZ78L05 50 25 0 0 -100 -200 -300 -40 Time (10s/Div) Time (4s/Div) Figure 9. Load Transient Response Figure 8. Line Transient Response (Conditions: VIN=10 to 11V, VOUT=5V, IOUT=40mA) Nov. 2012 Rev. 2. 2 (Conditions: VIN=10V, VOUT=5V, IOUT=1 to 50mA) BCD Semiconductor Manufacturing Limited 11 Data Sheet 3-TERMINAL POSITIVE LINEAR REGULATOR AZ78LXX Typical Application VIN 3 AZ78L05 VOUT 1 + + 2 0.33F (Note 4) 0.1F (Note 4) Note 4: Bypass capacitors are recommended for optimum stability and transient response and should be located as close as possible to the regulator. Figure 10. Typical Application of the AZ78LXX Nov. 2012 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 12 Data Sheet 3-TERMINAL POSITIVE LINEAR REGULATOR AZ78LXX Mechanical Dimensions TO-92(Bulk Packing) Unit: mm(inch) 1.000(0. 039) 3.430(0.135) MIN 3.700(0.146) 3.300(0.130) 1.400(0. 055) 0.320(0. 013) 0.510(0. 020) 0. 000(0. 000) 0. 380(0. 015) 1. 600(0. 063) MAX 4.700(0.185) 1.270(0. 050) TYP 15.500(0.610) 0.360(0. 014) 0.760(0. 030) 12.500(0.492) 4.300(0.169) 4.400(0.173) 4.800(0.189) 2.420(0.095) 2.660(0.105) Nov. 2012 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 13 Data Sheet 3-TERMINAL POSITIVE LINEAR REGULATOR AZ78LXX Mechanical Dimensions (Continued) TO-92(Ammo Packing) Unit: mm(inch) 1. 100(0. 043) 3. 430(0.135) MIN 1.270(0.050) Typ 2.500(0.098) 4.000 (0.157 ) 0. 000(0.000) 0. 380(0.015) 1. 600(0. 063) MAX 14.500(0.571) 12.500(0.492) 0.320(0. 013) 0. 510(0. 020) 3.800(0.150) 3.300(0.130) 1. 400(0.055) 4.700(0.185) 4.300(0.169) 4.400(0.173) 4.800 (0.189 ) 13.000(0. 512) 15.000 (0.591 ) 0.380(0.015) 0.550(0.022 ) 2.540(0.100) Typ Nov. 2012 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 14 Data Sheet 3-TERMINAL POSITIVE LINEAR REGULATOR AZ78LXX Mechanical Dimensions (Continued) SOT-223 Unit: mm(inch) 6.300(0.248) 6.700(0.264) ) 0.250(0.010 ) 4 1 0.350(0.0 2.900(0.114) 3.100(0.122) 0.900(0.035) 3.700(0.146) 3.300(0.130) 7.300(0.287) 6.700(0.264) MIN 0.250(0.010) 1.750(0.069) TYP 2.300(0.091) 0.610(0.024) TYP 0.810(0.032) 4.500(0.177) 0 10 4.700(0.185) 0.020(0.001) 0.100(0.004) 1.500(0.059) 1.520(0.060) 1.700(0.067) 1.800(0.071) Nov. 2012 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 15 Data Sheet 3-TERMINAL POSITIVE LINEAR REGULATOR AZ78LXX Mechanical Dimensions (Continued) SOT-89 1.550(0.061)REF Unit: mm(inch) 4.400(0.173) 4.600(0.181) 1.400(0.055) 1.600(0.063) 1.030(0.041)REF 45 2.300(0.091) 2.600(0.102) 3.950(0.156) 4.250(0.167) 2.060(0.081)REF 3 0.900(0.035) 1.100(0.043) 0.320(0.013) 0.520(0.020) 0.480(0.019) 0.320(0.013) 0.520(0.020) 10 0.350(0.014) 0.450(0.018) 3.000(0.118) TYP 1.500(0.059) 1.800(0.071) 0.320(0.013)REF 3 2.210(0.087)REF 1.620(0.064)REF R0.150(0.006) 10 Nov. 2012 Rev. 2. 2 BCD Semiconductor Manufacturing Limited 16 BCD Semiconductor Manufacturing Limited http://www.bcdsemi.com IMPORTANT NOTICE IMPORTANT NOTICE BCD Semiconductor BCD Semiconductor Manufacturing Manufacturing Limited Limited reserves reserves the the right right to to make make changes changes without without further further notice notice to to any any products products or or specifispecifications herein. cations herein. BCD BCD Semiconductor Semiconductor Manufacturing Manufacturing Limited Limited does does not not assume assume any any responsibility responsibility for for use use of of any any its its products products for for any any particular purpose, particular purpose, nor nor does does BCD BCD Semiconductor Semiconductor Manufacturing Manufacturing Limited Limited assume assume any any liability liability arising arising out out of of the the application application or or use use of any of any its its products products or or circuits. circuits. BCD BCD Semiconductor Semiconductor Manufacturing Manufacturing Limited Limited does does not not convey convey any any license license under under its its patent patent rights rights or or other rights other rights nor nor the the rights rights of of others. others. MAIN SITE SITE MAIN - Headquarters BCD Semiconductor Manufacturing Limited BCD Semiconductor Manufacturing Limited - Wafer Fab No. 1600, Zi Xing Road, Shanghai ZiZhu Science-basedLimited Industrial Park, 200241, China Shanghai SIM-BCD Semiconductor Manufacturing Tel: Fax: +86-21-24162277 800,+86-21-24162266, Yi Shan Road, Shanghai 200233, China Tel: +86-21-6485 1491, Fax: +86-21-5450 0008 REGIONAL SALES OFFICE Shenzhen OfficeSALES OFFICE REGIONAL - Wafer FabSemiconductor Manufacturing Limited BCD Shanghai SIM-BCD Semiconductor Manufacturing Co., Ltd. - IC Design Group 800 Yi Shan Road, Shanghai 200233, China Corporation Advanced Analog Circuits (Shanghai) Tel: +86-21-6485 1491,YiFax: 0008200233, China 8F, Zone B, 900, Shan+86-21-5450 Road, Shanghai Tel: +86-21-6495 9539, Fax: +86-21-6485 9673 Taiwan Office Shanghai Semiconductor Manufacturing Co., Ltd., Shenzhen Office BCD Taiwan Semiconductor Shenzhen SIM-BCD Office Office (Taiwan) Company Limited Unit A Room 1203, Skyworth Bldg., Gaoxin Ave.1.S., Nanshan Shenzhen, 4F, 298-1, Guang Road,(Taiwan) Nei-Hu District, Taipei, Shanghai SIM-BCD Semiconductor Manufacturing Co., Ltd.District, Shenzhen Office BCDRui Semiconductor Company Limited China Taiwan Advanced Analog Circuits (Shanghai) Corporation Shenzhen Office 4F, 298-1, Rui Guang Road, Nei-Hu District, Taipei, Tel: +86-755-8826 Tel: +886-2-2656 2808 Room E, 5F, Noble 7951 Center, No.1006, 3rd Fuzhong Road, Futian District, Shenzhen 518026, China Taiwan Fax: +86-755-88267951 7865 Fax: +886-2-2656 28062808 Tel: +86-755-8826 Tel: +886-2-2656 Fax: +86-755-8826 7865 Fax: +886-2-2656 2806 USA Office BCD Office Semiconductor Corp. USA 30920Semiconductor Huntwood Ave.Corporation Hayward, BCD CA 94544, USA Ave. Hayward, 30920 Huntwood Tel :94544, +1-510-324-2988 CA U.S.A Fax:: +1-510-324-2988 +1-510-324-2788 Tel Fax: +1-510-324-2788