1© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard T2001_T409 • 8/27/2018
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
One world. One KEMET
Benets
• Established reliability options
• Taped and reeled per EIA 481
• Symmetrical, compliant terminations
• Laser-marked case
• 100% surge current test available on all case sizes
• QualiedtoMIL-PRF-55365/4(CWR09Style)
• Termination options B, C, H, and K
• WeibullfailureoptionsB,C,D,andT
• ExponentialfailureratesM,P,R,andS
• Voltageratingof4–50VDC
• Operatingtemperaturerangeof−55°Cto+125°C
Overview
TheKEMETT409isapprovedtoMIL-PRF-55365/4(CWR09
Style)withWeibullfailureratesofBlevel(0.1%failures
per1,000hours),Clevel(0.01%failuresper1,000hours),
Dlevel(0.001%failuresper1,000hours),orTlevel(0.01%
failuresper1,000hours,optionCsurgecurrent,DPA,
radiographicinspection,100%visualinspection,DCLand
ESRmeasurementswithin+3standarddeviations,andGroup
Cinspection).ThisCWR09productisaprecision-molded
device with compliant terminations and indelible laser
marking. Tape and reeling per EIA 481 are standard.
TantalumSurfaceMountCapacitors–MIL-PRF(CWRStyle)
T409 MIL-PRF-55365/4 (CWR09 Style)
Applications
TypicalapplicationsincludedecouplingandlteringinmilitaryandaerospaceapplicationsrequiringCWR09devices.
K-SIM
Foradetailedanalysisofspecicpartnumbers,pleasevisitksim.kemet.comtoaccessKEMET’sK-SIMsoftware.KEMET
K-SIMisdesignedtosimulatebehaviorofcomponentswithrespecttofrequency,ambienttemperature,andDCbiaslevels.
Click image above for interactive 3D content
Open PDF in Adobe Reader for full functionality
2© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard T2001_T409 • 8/27/2018
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
2
Tantalum Surface Mount Capacitors – MIL-PRF (CWR Style)
T409 MIL-PRF-55365/4 (CWR09 Style)
KEMET Ordering Information
T409 A225 K004 A H 4252 7280
Capacitor
Class Series Case
Size
Capacitance
Code(pF)
Capacitance
Tolerance
Rated
Voltage
(VDC)
FailureRate/Design Termination
Finish Surge Packaging
(C-Spec)
T =
Tantalum
CWR09
Established
reliability
A
B
C
D
E
F
G
H
First two
digits
represent
signicant
gures.
Third digit
species
numberof
zeros.
J = ±5%
K = ±10%
M = ±20%
004 = 4
006 = 6.3
010 = 10
015 = 15
020 = 20
025 = 25
035 = 35
050 = 50
Weibull
A=non-ER
B=(0.1%/1,000hours)
C=(0.01%/1,000hours)
D=(0.001%/1,000
hours)
T=(0.01%/1,000hours)
Exponential
M=(1.0%/1,000hours)
P=(0.1%/1,000hours)
R=(0.01%/1,000hours)
S=(0.001%/1,000hours)
C = Hot solder
dipped
H = Standard
solder-coated
(SnPb5%Pb
minimum)
B=Gold-plated
K = Solder
fused
4250=25°C
afterWeibull
4251=−55°C
and85°Cafter
Weibull
4252=−55°C
and85°C
beforeWeibull
TLVL=Weibull
grade level "T"
Blank=7"Reel
7280=13"Reel
7610 = Bulk bag
7005 = Moisture
bags
7640 = Bulk
plastic box
WAFL=Wae
pack
Ordering Information – Defense MIL-PRF-55365/4
CWR09 J H 105 K C A
Capacitor Style
Rated
Voltage
(VDC)
Termination
Finish
Capacitance
Code
(pF)
Tolerance ReliabilityLevel Surge Current Option
Per
MIL-PRF-55365/4
C = 4
D=6
F = 10
H = 15
J = 20
K = 25
M = 35
N = 50
B=Gold-plated
C = Hot solder
dipped
H = Solder
plated
K = Solder
fused
First two digits
represent
signicant
gures.Third
digitspecies
numberof
zeros.
J = ±5%
K = ±10%
M = ±20%
Weibull
A=non-ER
B=(0.1%/1,000hours)
C=(0.01%/1,000hours)
D=(0.001%/1,000hours)
T=TLevel*(0.01%/1,000hours)
Exponential
M=(1.0%/1,000hours)
P=(0.1%/1,000hours)
R=(0.01%/1,000hours)
S=(0.001%/1,000hours)
A=+25°CafterWeibull
B=−55°C+85°CafterWeibull
C=−55°C+85°CbeforeWeibull
Blank = No surge
* When T Level is ordered, no Surge Current Option is needed
Performance Characteristics
Item Performance Characteristics
Operating Temperature −55°Cto125°C
RatedCapacitanceRange 0.1–100µFat120Hz/25°C
Capacitance Tolerance JTolerance(5%),KTolerance(10%),MTolerance(20%)
RatedVoltageRange 4–50V
DF(120Hz) RefertoPartNumberElectricalSpecicationTable
ESR(100kHz) RefertoPartNumberElectricalSpecicationTable
Leakage Current ≤0.01CV(µA)atratedvoltageafter5minutes
3© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard T2001_T409 • 8/27/2018
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
3
Tantalum Surface Mount Capacitors – MIL-PRF (CWR Style)
T409 MIL-PRF-55365/4 (CWR09 Style)
Qualication
Test Condition Characteristics
Endurance 85°Catratedvoltage,2,000hours
125°Cat2/3ratedvoltage,2,000hours
ΔC/C Within±10%ofinitialvalue
DF Withininitiallimits
DCL Within1.25xinitiallimit
ESR Withininitiallimits
StorageLife 125°Cat0volts,2,000hours
ΔC/C Within±10%ofinitialvalue
DF Withininitiallimits
DCL Within1.25xinitiallimit
ESR Withininitiallimits
Thermal Shock MIL-STD-202,Method107,conditionB,mounted,−55C°
to125°C,1,000cycles
ΔC/C Within±5%ofinitialvalue
DF Withininitiallimits
DCL Within1.25xinitiallimit
ESR Withininitiallimits
Temperature Stability
Extreme temperature exposure at a
successionofcontinuousstepsat+25°C,
−55°C,+25°C,+85°C,+125°C,+25°C
+25°C −55°C +85°C +125°C
ΔC/C IL* ±10% ±10% ±15%
DF IL IL 1.5 x IL 1.5 x IL
DCL IL N/A 10 x IL 12 x IL
Surge Voltage 25°Cand85°C,1.32xratedvoltage1,000cycles
(125°C,1.2xratedvoltage)
ΔC/C Within±5%ofinitialvalue
DF Withininitiallimits
DCL Withininitiallimits
ESR Withininitiallimits
Mechanical Shock/
Vibration
MIL-STD-202,Method213,ConditionI,100Gpeak
MIL-STD-202,Method204,ConditionD,10Hzto2,000
Hz,20Gpeak
ΔC/C Within±10%ofinitialvalue
DF Withininitiallimits
DCL Withininitiallimits
Additionalqualication
testsperMIL-PRF-55365/4 PleasecontactKEMETformoreinformation.
*IL = Initial limit
Certication
MIL-PRF-55365/4
4© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard T2001_T409 • 8/27/2018
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
4
Tantalum Surface Mount Capacitors – MIL-PRF (CWR Style)
T409 MIL-PRF-55365/4 (CWR09 Style)
0.1
1
10
100
100 1,000 10,000 100,000 1,000,000 10,000,000
Capacitance (µF)
Frequency (Hz)
T409D475/010
T409F156/010
T409H476/010
Capacitancevs.Frequency
ESRvs.Frequency
0.1
1
10
100
1,000
100 1,000 10,000 100,000 1,000,000 10,000,000
Impedance, ESR (Ohms)
Frequency (Hz)
T409D475/010_IMP
T409F156/010_IMP
T409H476/010_IMP
T409D475/010_ESR
T409F156/010_ESR
T409F476/010_ESR
Electrical Characteristics
5© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard T2001_T409 • 8/27/2018
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
5
Tantalum Surface Mount Capacitors – MIL-PRF (CWR Style)
T409 MIL-PRF-55365/4 (CWR09 Style)
Dimensions – Millimeters (Inches)
Metric will govern
W
½ H
2
Min.
P
L
SIDE VIEW
BOTTOM VIEW
END VIEW
P
W2
H
2
H
Solderable
Surfaces
Termination cutout
at KEMET's option,
either end
Case Size Component Typical Weight
KEMET L±0.38(0.015) W±0.38(0.015) H±0.38(0.015) P+0.25(0.010),
−0.13(0.005) W2H2 Minimum (mg)
A2.54(0.100) 1.27(0.050) 1.27(0.050) 0.76(0.030)
1.27 ±0.13
(0.050±0.005)
0.76(0.030) 39.91
B3.81(0.150) 1.27(0.050) 1.27(0.050) 0.76(0.030)
1.27 ±0.13
(0.050±0.005)
0.76(0.030) 68.73
C5.08(0.200) 1.27(0.050) 1.27(0.050) 0.76(0.030)
1.27 ±0.13
(0.050±0.005)
0.76(0.030) 146.5
D3.81(0.150) 2.54(0.100) 1.27(0.050) 0.76(0.030)
2.41+0.13,−0.25
(0.095+0.005,−0.010)
0.76(0.030) 264.12
E5.08(0.200) 2.54(0.100) 1.27(0.050) 0.76(0.030)
2.41+0.13,−0.25
(0.095+0.005,−0.010)
0.76(0.030) 421.63
F5.59(0.220) 3.43(0.135) 1.78(0.070) 0.76(0.030)
3.30 ±0.13
(0.130±0.005)
1.02(0.040) 173.63
G 6.73(0.265) 2.79(0.110) 2.79(0.110) 1.27(0.050)
2.67 ±0.13
(0.105±0.005)
1.52(0.060) 266.42
H7.24(0.285) 3.81(0.150) 2.79(0.110) 1.27(0.050)
3.68+0.013,−0.51
(0.145+0.005,−0.020)
1.52(0.060) 349.01
Note: When option C is selected for lead material, add an additional 0.38 mm (0.015 inch) to the above tolerances for "L", "W", "H", "P", "W2," and "H2."
These weights are provided as reference. If exact weights are needed, please contact your KEMET sales representative.
6© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard T2001_T409 • 8/27/2018
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
6
Tantalum Surface Mount Capacitors – MIL-PRF (CWR Style)
T409 MIL-PRF-55365/4 (CWR09 Style)
Table 1 – Ratings & Part Number Reference
(1) To complete KEMET/CWR part number, insert M for ±20%, K for ±10%, or J for ±5%. Designates Capacitance Tolerance.
(2) To complete KEMET/CWR part number, insert failure rate letter per the Ordering Information found on page 2. Designates Reliability Level.
(3) To complete KEMET/CWR part number, insert B = Gold-plated, C = Hot solder dipped, H = Solder plated or K = Solder fused. Designates termination
nish.
(4) To complete KEMET part number, insert 4250 = +25°C after Weibull, 4251 = −55°C +85°C after Weibull, or 4252 = −55°C +85°C before Weibull.
Designates Surge Current Option.
(5) To complete CWR part number, insert A = +25°C after Weibull, B = −55°C +85°C after Weibull, or C = −55°C +85°C before Weibull. Designates surge
current option. Refer to Ordering Information for additional detail.
Rated
Voltage
Rated
Cap
Case
Code/
Case Size
KEMET Part
Number
MIL-PRF-55365/4
Part Number
DC
Leakage DF ESR
Maximum
Operating
Temp
MSL
VDC @ 85°C µF KEMET/EIA (See below for
part options)
(See below for
part options)
µA @ +20°C
Maximum/5
Minutes
% @ +20°C
120 Hz
Maximum
Ω @ +20°C
100 kHz
Maximum
°C Reow Temp
≤ 260°C
42.2 A/1005 T409A225(1)004(2)(3)(4) CWR09C(3)225(1)(2)(5) 16.0 8.0 125 1
44.7 B/1505 T409B475(1)004(2)(3)(4) CWR09C(3)475(1)(2)(5) 1.0 6.0 8.0 125 1
46.8 C/2005 T409C685(1)004(2)(3)(4) CWR09C(3)685(1)(2)(5) 1.0 6.0 5.5 125 1
410 D/1510 T409D106(1)004(2)(3)(4) CWR09C(3)106(1)(2)(5) 1.0 8.0 4.0 125 1
415 E/2010 T409E156(1)004(2)(3)(4) CWR09C(3)156(1)(2)(5) 1.0 8.0 3.5 125 1
433 F/2214 T409F336(1)004(2)(3)(4) CWR09C(3)336(1)(2)(5) 2.0 8.0 2.2 125 1
468 G/2711 T409G686(1)004(2)(3)(4) CWR09C(3)686(1)(2)(5) 3.0 10.0 1.1 125 1
4100 H/2915 T409H107(1)004(2)(3)(4) CWR09C(3)107(1)(2)(5) 4.0 10.0 0.9 125 1
61.5 A/1005 T409A155(1)006(2)(3)(4) CWR09D(3)155(1)(2)(5) 1.0 6.0 8.0 125 1
63.3 B/1505 T409B335(1)006(2)(3)(4) CWR09D(3)335(1)(2)(5) 1.0 6.0 8.0 125 1
64.7 C/2005 T409C475(1)006(2)(3)(4) CWR09D(3)475(1)(2)(5) 1.0 6.0 5.5 125 1
66.8 D/1510 T409D685(1)006(2)(3)(4) CWR09D(3)685(1)(2)(5) 1.0 6.0 4.5 125 1
610 E/2010 T409E106(1)006(2)(3)(4) CWR09D(3)106(1)(2)(5) 1.0 8.0 3.5 125 1
622 F/2214 T409F226(1)006(2)(3)(4) CWR09D(3)226(1)(2)(5) 2.0 8.0 2.2 125 1
647 G/2711 T409G476(1)006(2)(3)(4) CWR09D(3)476(1)(2)(5) 3.0 10.0 1.1 125 1
668 H/2915 T409H686(1)006(2)(3)(4) CWR09D(3)686(1)(2)(5) 4.0 10.0 0.9 125 1
10 1A/1005 T409A105(1)010(2)(3)(4) CWR09F(3)105(1)(2)(5) 1.0 6.0 10.0 125 1
10 2.2 B/1505 T409B225(1)010(2)(3)(4) CWR09F(3)225(1)(2)(5) 1.0 6.0 8.0 125 1
10 3.3 C/2005 T409C335(1)010(2)(3)(4) CWR09F(3)335(1)(2)(5) 1.0 6.0 5.5 125 1
10 4.7 D/1510 T409D475(1)010(2)(3)(4) CWR09F(3)475(1)(2)(5) 1.0 6.0 4.5 125 1
10 6.8 E/2010 T409E685(1)010(2)(3)(4) CWR09F(3)685(1)(2)(5) 1.0 6.0 3.5 125 1
10 15 F/2214 T409F156(1)010(2)(3)(4) CWR09F(3)156(1)(2)(5) 2.0 8.0 2.5 125 1
10 33 G/2711 T409G336(1)010(2)(3)(4) CWR09F(3)336(1)(2)(5) 3.0 10.0 1.1 125 1
10 47 H/2915 T409H476(1)010(2)(3)(4) CWR09F(3)476(1)(2)(5) 5.0 10.0 0.9 125 1
15 0.68 A/1005 T409A684(1)015(2)(3)(4) CWR09H(3)684(1)(2)(5) 1.0 6.0 12.0 125 1
15 1.5 B/1505 T409B155(1)015(2)(3)(4) CWR09H(3)155(1)(2)(5) 1.0 6.0 8.0 125 1
15 2.2 C/2005 T409C225(1)015(2)(3)(4) CWR09H(3)225(1)(2)(5) 1.0 6.0 5.5 125 1
15 3.3 D/1510 T409D335(1)015(2)(3)(4) CWR09H(3)335(1)(2)(5) 1.0 6.0 5.0 125 1
15 4.7 E/2010 T409E475(1)015(2)(3)(4) CWR09H(3)475(1)(2)(5) 1.0 6.0 4.0 125 1
15 10 F/2214 T409F106(1)015(2)(3)(4) CWR09H(3)106(1)(2)(5) 2.0 6.0 2.5 125 1
15 22 G/2711 T409G226(1)015(2)(3)(4) CWR09H(3)226(1)(2)(5) 4.0 6.0 1.1 125 1
15 33 H/2915 T409H336(1)015(2)(3)(4) CWR09H(3)336(1)(2)(5) 5.0 8.0 0.9 125 1
20 0.47 A/1005 T409A474(1)020(2)(3)(4) CWR09J(3)474(1)(2)(5) 1.0 8.0 14.0 125 1
20 0.68 B/1505 T409B684(1)020(2)(3)(4) CWR09J(3)684(1)(2)(5) 1.0 6.0 10.0 125 1
20 1B/1505 T409B105(1)020(2)(3)(4) CWR09J(3)105(1)(2)(5) 1.0 6.0 12.0 125 1
20 1.5 C/2005 T409C155(1)020(2)(3)(4) CWR09J(3)155(1)(2)(5) 1.0 6.0 6.0 125 1
20 2.2 D/1510 T409D225(1)020(2)(3)(4) CWR09J(3)225(1)(2)(5) 1.0 6.0 5.0 125 1
20 3.3 E/2010 T409E335(1)020(2)(3)(4) CWR09J(3)335(1)(2)(5) 1.0 6.0 4.0 125 1
20 6.8 F/2214 T409F685(1)020(2)(3)(4) CWR09J(3)685(1)(2)(5) 2.0 6.0 2.4 125 1
20 15 G/2711 T409G156(1)020(2)(3)(4) CWR09J(3)156(1)(2)(5) 3.0 6.0 1.1 125 1
20 22 H/2915 T409H226(1)020(2)(3)(4) CWR09J(3)226(1)(2)(5) 4.0 6.0 0.9 125 1
25 0.33 A/1005 T409A334(1)025(2)(3)(4) CWR09K(3)334(1)(2)(5) 1.0 6.0 15.0 125 1
25 0.68 B/1505 T409B684(1)025(2)(3)(4) CWR09K(3)684(1)(2)(5) 1.0 6.0 7.5 125 1
25 1C/2005 T409C105(1)025(2)(3)(4) CWR09K(3)105(1)(2)(5) 1.0 6.0 6.5 125 1
25 1.5 D/1510 T409D155(1)025(2)(3)(4) CWR09K(3)155(1)(2)(5) 1.0 6.0 6.5 125 1
25 2.2 E/2010 T409E225(1)025(2)(3)(4) CWR09K(3)225(1)(2)(5) 1.0 6.0 3.5 125 1
VDC @ 85°C µF KEMET/EIA (See below for
part options)
(See below for
part options)
µA @ +20°C
Maximum/5
Minutes
% @ +20°C
120 Hz
Maximum
Ω @ +20°C
100 kHz
Maximum
°C Reow Temp
≤ 260°C
Rated
Voltage
Rated
Cap
Case Code/
Case Size KEMET Part Number MIL-PRF-55365/4
Part Number
DC
Leakage DF ESR Maximum
Operating Temp MSL
7© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard T2001_T409 • 8/27/2018
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
7
Tantalum Surface Mount Capacitors – MIL-PRF (CWR Style)
T409 MIL-PRF-55365/4 (CWR09 Style)
Table 1 – Ratings & Part Number Reference cont'd
(1) To complete KEMET/CWR part number, insert M for ±20%, K for ±10%, or J for ±5%. Designates Capacitance Tolerance.
(2) To complete KEMET/CWR part number, insert failure rate letter per the Ordering Information found on page 2. Designates Reliability Level.
(3) To complete KEMET/CWR part number, insert B = Gold-plated, C = Hot solder dipped, H = Solder plated or K = Solder fused. Designates termination
nish.
(4) To complete KEMET part number, insert 4250 = +25°C after Weibull, 4251 = −55°C +85°C after Weibull, or 4252 = −55°C +85°C before Weibull.
Designates Surge Current Option.
(5) To complete CWR part number, insert A = +25°C after Weibull, B = −55°C +85°C after Weibull, or C = −55°C +85°C before Weibull. Designates surge
current option. Refer to Ordering Information for additional detail.
Rated
Voltage
Rated
Cap
Case
Code/
Case Size
KEMET Part
Number
MIL-PRF-55365/4
Part Number
DC
Leakage DF ESR
Maximum
Operating
Temp
MSL
VDC @ 85°C µF KEMET/EIA (See below for
part options)
(See below for
part options)
µA @ +20°C
Maximum/5
Minutes
% @ +20°C
120 Hz
Maximum
Ω @ +20°C
100 kHz
Maximum
°C Reow Temp
≤ 260°C
25 4.7 F/2214 T409F475(1)025(2)(3)(4) CWR09K(3)475(1)(2)(5) 2.0 6.0 2.5 125 1
25 6.8 G/2711 T409G685(1)025(2)(3)(4) CWR09K(3)685(1)(2)(5) 2.0 6.0 1.2 125 1
25 10 G/2711 T409G106(1)025(2)(3)(4) CWR09K(3)106(1)(2)(5) 3.0 6.0 1.4 125 1
25 15 H/2915 T409H156(1)025(2)(3)(4) CWR09K(3)156(1)(2)(5) 4.0 6.0 1.0 125 1
35 0.22 A/1005 T409A224(1)035(2)(3)(4) CWR09M(3)224(1)(2)(5) 1.0 6.0 18.0 125 1
35 0.47 B/1505 T409B474(1)035(2)(3)(4) CWR09M(3)474(1)(2)(5) 1.0 6.0 10.0 125 1
35 0.68 C/2005 T409C684(1)035(2)(3)(4) CWR09M(3)684(1)(2)(5) 1.0 6.0 8.0 125 1
35 1D/1510 T409D105(1)035(2)(3)(4) CWR09M(3)105(1)(2)(5) 1.0 6.0 6.5 125 1
35 1.5 E/2010 T409E155(1)035(2)(3)(4) CWR09M(3)155(1)(2)(5) 1.0 6.0 4.5 125 1
35 3.3 F/2214 T409F335(1)035(2)(3)(4) CWR09M(3)335(1)(2)(5) 1.0 6.0 2.5 125 1
35 4.7 G/2711 T409G475(1)035(2)(3)(4) CWR09M(3)475(1)(2)(5) 2.0 6.0 1.5 125 1
35 6.8 H/2915 T409H685(1)035(2)(3)(4) CWR09M(3)685(1)(2)(5) 3.0 6.0 1.3 125 1
50 0.1 A/1005 T409A104(1)050(2)(3)(4) CWR09N(3)104(1)(2)(5) 1.0 6.0 22.0 125 1
50 0.15 A/1005 T409A154(1)050(2)(3)(4) CWR09N(3)154(1)(2)(5) 1.0 6.0 17.0 125 1
50 0.22 B/1505 T409B224(1)050(2)(3)(4) CWR09N(3)224(1)(2)(5) 1.0 6.0 14.0 125 1
50 0.33 B/1505 T409B334(1)050(2)(3)(4) CWR09N(3)334(1)(2)(5) 1.0 6.0 12.0 125 1
50 0.47 C/2005 T409C474(1)050(2)(3)(4) CWR09N(3)474(1)(2)(5) 1.0 6.0 8.0 125 1
50 0.68 D/1510 T409D684(1)050(2)(3)(4) CWR09N(3)684(1)(2)(5) 1.0 6.0 7.0 125 1
50 1E/2010 T409E105(1)050(2)(3)(4) CWR09N(3)105(1)(2)(5) 1.0 6.0 6.0 125 1
50 1.5 F/2214 T409F155(1)050(2)(3)(4) CWR09N(3)155(1)(2)(5) 1.0 6.0 4.0 125 1
50 2.2 F/2214 T409F225(1)050(2)(3)(4) CWR09N(3)225(1)(2)(5) 2.0 6.0 2.5 125 1
50 3.3 G/2711 T409G335(1)050(2)(3)(4) CWR09N(3)335(1)(2)(5) 2.0 6.0 2.0 125 1
50 4.7 H/2915 T409H475(1)050(2)(3)(4) CWR09N(3)475(1)(2)(5) 3.0 6.0 1.5 125 1
VDC @ 85°C µF KEMET/EIA (See below for
part options)
(See below for
part options)
µA @ +20°C
Maximum/5
Minutes
% @ +20°C
120 Hz
Maximum
Ω @ +20°C
100 kHz
Maximum
°C Reow Temp
≤ 260°C
Rated
Voltage
Rated
Cap
Case Code/
Case Size KEMET Part Number MIL-PRF-55365/4
Part Number
DC
Leakage DF ESR Maximum
Operating Temp MSL
8© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard T2001_T409 • 8/27/2018
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
8
Tantalum Surface Mount Capacitors – MIL-PRF (CWR Style)
T409 MIL-PRF-55365/4 (CWR09 Style)
Recommended Voltage Derating Guidelines
−55°Cto85°C 85°Cto125°C
%ChangeinWorkingDC
Voltage with Temperature
VR67%ofVR
RecommendedMaximum
Application Voltage
50%ofVR33%ofVR
Ripple Current/Ripple Voltage
PermissibleACripplevoltageandcurrentarerelatedto
equivalentseriesresistance(ESR)andthepowerdissipation
capabilitiesofthedevice.PermissibleACripplevoltage
which may be applied is limited by two criteria:
1.ThepositivepeakACvoltageplustheDCbiasvoltage,
ifany,mustnotexceedtheDCvoltageratingofthe
capacitor.
2. The negative peak AC voltage in combination with
biasvoltage,ifany,mustnotexceedtheallowablelimits
speciedforthereversevoltage.SeetheReverseVoltage
sectionforallowablelimits.
The maximum power dissipation by case size can be
determined using the table at right. The maximum power
dissipation rating stated in the table must be reduced with
increasingenvironmentaloperatingtemperatures.Referto
thetablebelowfortemperaturecompensationrequirements.
Temperature Compensation Multipliers
for Maximum Ripple Current
T≤25°C
T≤85°C
T≤125°C
1.00
0.90
0.40
T = Environmental Temperature
The maximum power dissipation rating must be reduced with increasing
environmental operating temperatures. Refer to the Temperature
Compensation Multiplier table for details.
KEMET
Case Code
EIA
Case Code
Maximum Power
Dissipation (P max)
mWatts at 25°C
w/+20°C Rise
A
1005
50
B
1505
70
C
2005
75
D
1510
80
E
2010
90
F
2214
100
G
2711
125
H
2915
150
UsingthePmaxofthedevice,themaximumallowablerms
ripple current or voltage may be determined.
I(max) = √P max/R
E(max) = Z √P max/R
I = rms ripple current (amperes)
E = rms ripple voltage (volts)
P max = maximum power dissipation (watts)
R = ESR at specied frequency (ohms)
Z = Impedance at specied frequency (ohms)
0%
20%
40%
60%
80%
100%
120%
−55 25 85 125
% Working Voltage
% Change in Working DC Voltage
with Temperature
Temperature (ºC)
67%
33%
Recommended Maximum
Application Voltage
(As % of Rated Voltage)
9© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard T2001_T409 • 8/27/2018
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
9
Tantalum Surface Mount Capacitors – MIL-PRF (CWR Style)
T409 MIL-PRF-55365/4 (CWR09 Style)
Reverse Voltage
Solidtantalumcapacitorsarepolardevicesandmaybepermanentlydamagedordestroyedifconnectedwiththewrong
polarity.Thepositiveterminalisidentiedonthecapacitorbodybyastripe,plus,insomecasesabevelededge.Asmall
degreeoftransientreversevoltageispermissibleforshortperiodsperthetable.Thecapacitorsshouldnotbeoperated
continuously in reverse mode, even within these limits.
Temperature Permissible Transient Reverse Voltage
25°C
15%ofRatedVoltage
85°C
5%ofRatedVoltage
125°C
1%ofRatedVoltage
Table 2 – Land Dimensions/Courtyard
KEMET
Metric
Size
Code
Density Level A:
Maximum (Most) Land
Protrusion (mm)
Density Level B:
Median (Nominal) Land
Protrusion (mm)
Density Level C:
Minimum (Least) Land
Protrusion (mm)
Case
EIA
L
W
S
V1
V2
L
W
S
V1
V2
L
W
S
V1
V2
A
1
1005
2.19
1.44
0.15
5.54
2.66
1.89
1.32
0.15
4.44
2.16
1.52
1.22
0.29
3.58
1.90
B
1505
2.30
1.44
1.20
6.80
2.66
1.90
1.32
1.40
5.70
2.16
1.52
1.22
1.56
4.84
1.90
C
2005
2.30
1.44
2.47
8.08
2.66
1.90
1.32
2.67
6.98
2.16
1.52
1.22
2.83
6.12
1.90
D
1510
2.30
2.58
1.20
6.80
3.92
1.90
2.46
1.40
5.70
3.42
1.52
2.36
1.56
4.84
3.16
E
2010
2.30
2.58
2.47
8.08
3.92
1.90
2.46
2.67
6.98
3.42
1.52
2.36
2.83
6.12
3.16
F
2214
2.30
3.47
2.98
8.58
4.82
1.90
3.35
3.18
7.48
4.32
1.52
3.25
3.34
6.62
4.06
G
2711
2.81
2.84
3.10
9.72
4.18
2.41
2.72
3.30
8.62
3.68
2.03
2.62
3.46
7.76
3.42
H
2915
2.81
3.84
3.61
10.24
5.20
2.41
3.72
3.81
9.14
4.70
2.03
3.62
3.97
8.28
4.44
X
2824
2.73
3.22
3.46
9.92
6.80
2.33
3.10
3.66
8.82
6.30
1.95
3.00
3.82
7.96
6.04
Density Level A: For low-density product applications. Recommended for wave solder applications and provides a wider process window for reow
solder processes.
Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reow solder processes.
Density Level C: For high component desity product applications. Before adapting the minimum land pattern variations, the user should perform
qualication testing based on the conditions outlined in IPC standard 7351 (IPC–7351).
1 Land pattern geometry is too small for silkscreen outline.
L
S
W W
L
V1
V2
Grid Placement Courtyard
10© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard T2001_T409 • 8/27/2018
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
10
Tantalum Surface Mount Capacitors – MIL-PRF (CWR Style)
T409 MIL-PRF-55365/4 (CWR09 Style)
Soldering Process
KEMET’sfamiliesofsurfacemountcapacitorsarecompatible
withwave(singleordual),convection,IR,orvaporphase
reowtechniques.Preheatingofthesecomponentsis
recommended to avoid extreme thermal stress. KEMET's
recommendedproleconditionsforconvectionandIR
reowreecttheproleconditionsoftheIPC/J–STD–020D
standardformoisturesensitivitytesting.Thedevicescan
safelywithstandamaximumofthreereowpassesatthese
conditions.
PleasenotethatalthoughtheX/7343–43casesizecan
withstandwavesoldering,thetallprole(4.3mmmaximum)
dictates care in wave process development.
Handsolderingshouldbeperformedwithcareduetothe
dicultyinprocesscontrol.Ifperformed,careshouldbe
takentoavoidcontactofthesolderingirontothemolded
case. The iron should be used to heat the solder pad, applying
solderbetweenthepadandthetermination,untilreow
occurs.Oncereowoccurs,theironshouldberemoved
immediately.“Wiping”theedgesofachipandheatingthetop
surfaceisnotrecommended.
Duringtypicalreowoperations,aslightdarkeningofthe
gold-colored epoxy may be observed. This slight darkening is
normalandnotharmfultotheproduct.Markingpermanency
isnotaffectedbythischange.
Prole Feature SnPb Assembly
Pb-Free Assembly
Preheat/Soak
TemperatureMinimum(T
Smin
)100°C 150°C
TemperatureMaximum(T
Smax
)150°C 200°C
Time(t
s
)fromT
smin
to T
smax
) 60–120seconds 60–120seconds
Ramp-upRate(T
L
to T
P
)3°C/secondmaximum 3°C/secondmaximum
LiquidousTemperature(T
L
)183°C 217°C
TimeAboveLiquidous(t
L
) 60–150seconds 60–150seconds
PeakTemperature(TP)
220°C*
235°C**
250°C*
260°C**
Timewithin5°CofMaximum
PeakTemperature(tP)
20 seconds maximum 30 seconds maximum
Ramp-downRate(T
P
to T
L
)6°C/secondmaximum 6°C/secondmaximum
Time25°CtoPeak
Temperature
6 minutes maximum 8 minutes maximum
Note: All temperatures refer to the center of the package, measured on the
package body surface that is facing up during assembly reow.
* For Case Size height > 2.5 mm
** For Case Size height ≤ 2.5 mm
Storage
Tantalumchipcapacitorsshouldbestoredinnormalworkingenvironments.Whilethechipsthemselvesarequiterobustin
other environments, solderability will be degraded by exposure to high temperatures, high humidity, corrosive atmospheres,
andlongtermstorage.Inaddition,packagingmaterialswillbedegradedbyhightemperature–reelsmaysoftenorwarp
andtapepeelforcemayincrease.KEMETrecommendsthatmaximumstoragetemperaturenotexceed40°Candmaximum
storagehumiditynotexceed60%relativehumidity.Temperatureuctuationsshouldbeminimizedtoavoidcondensationon
thepartsandatmospheresshouldbefreeofchlorineandsulphurbearingcompounds.Foroptimizedsolderabilitychipstock
shouldbeusedpromptly,preferablywithinthreeyearsofreceipt.
Time
Temperature
Tsmin
25
Tsmax
TL
TPMaximum Ramp Up Rate = 3°C/second
Maximum Ramp Down Rate = 6°C/second
tP
tL
ts
25°C to Peak
11© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard T2001_T409 • 8/27/2018
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
11
Tantalum Surface Mount Capacitors – MIL-PRF (CWR Style)
T409 MIL-PRF-55365/4 (CWR09 Style)
Construction
Leadframe
(− Cathode)
Leadframe
(+ Anode)
Tantalum Wire
Molded Epoxy
Case
Molded Epoxy
Case
Polarity Stripe (+)
Weld
(to attach wire)
Silver Adhesive
Detailed Cross Section
Tantalum Wire
Tantalum
Ta2O5 Dielectric
(First Layer)
Carbon
(Third Layer)
Silver Paint
(Fourth Layer)
Washer
Washer
MnO2
(Second Layer)
Capacitor Marking
KEMET CWR
09 Style Polarity
Indicator (+)
Rated
Voltage
Picofarad
Code
KEMET
ID
Date
Code*
* 230 = 30th week of 2012
Date Code *
1stdigit=lastnumberofyear 2 = 2012
3 = 2013
4 = 2014
5 = 2015
6 = 2016
7 = 2017
2nd and 3rddigit=weekofthe
year
01 = 1stweekoftheyearto
52 = 52ndweekoftheyear
12© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard T2001_T409 • 8/27/2018
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
12
Tantalum Surface Mount Capacitors – MIL-PRF (CWR Style)
T409 MIL-PRF-55365/4 (CWR09 Style)
Tape & Reel Packaging Information
KEMET’smoldedtantalumandaluminumchipcapacitorfamiliesarepackagedin8and12mmplastictapeon7"and13"
reels in accordance with EIA Standard 481:EmbossedCarrierTapingofSurfaceMountComponentsforAutomaticHandling.
Thispackagingsystemiscompatiblewithalltape-fedautomaticpick-and-placesystems.
Embossment
8 mm (0.315”) or
12 mm (0.472”)
Embossed carrier
Right hand
orientation
only
(+) (−)
Top tape thickness
0.10 mm (0.004”)
maximum thickness
180 mm (7.0”) or
330 mm (13.”)
Table 3 – Packaging Quantity
KEMET Case
Codes
Tape
Width
(mm)
Tape and Reel Dimensions
180 mm
(7" diameter)
330 mm
(13" diameter)
A
1005
8
2,500
9,500
B
1505
12
2,500
9,500
C
2005
12
2,500
9,500
D
1510
12
2,500
9,500
E
2010
12
2,500
9,500
F
2214
12
500
3,500
G
2711
12
500
2,500
H
2915
12
500
2,500
X
2824
12
500
2,500
13© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard T2001_T409 • 8/27/2018
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
13
Tantalum Surface Mount Capacitors – MIL-PRF (CWR Style)
T409 MIL-PRF-55365/4 (CWR09 Style)
Figure 1 – Embossed (Plastic) Carrier Tape Dimensions
P
0
T
F
W
Center Lines of Cavity
A
0
B
0
User Direction of Unreeling
Cover Tape
K
0
B
1
is for tape feeder reference only,
including draft concentric about B
0
.
T
2
ØD
1
ØD
0
B
1
S
1
T
1
E
1
E
2
P
1
P
2
Embossment
For cavity size,
see Note 1, Table 4
(10 pitches cumulative
tolerance on tape ±0.2 mm)
Table 4 – Embossed (Plastic) Carrier Tape Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
Tape Size D0
D
1
Minimum
Note 1
E1P0 P2
RReference
Note 2
1
T Maximum
T
1
Maximum
8 mm 1.5+0.10/-0.0
(0.059+0.004/-0.0)
1.0
(0.039) 1.75±0.10
(0.069±0.004)
4.0±0.10
(0.157±0.004)
2.0±0.05
(0.079±0.002)
25.0
(0.984) 0.600
(0.024)
0.600
(0.024)
0.100
(0.004)
12 mm 1.5
(0.059)
30
(1.181)
Variable Dimensions — Millimeters (Inches)
Tape Size Pitch
B
1
Maximum
Note 4
E2 Minimum F P1 T2 Maximum WMaximum A0, B0 & K0
8 mm Single(4mm) 4.35
(0.171)
6.25
(0.246)
3.5±0.05
(0.138±0.002)
2.0±0.05 or 4.0±0.10
(0.079±0.002or0.157±0.004)
2.5
(0.098)
8.3
(0.327)
Note 5
12 mm
Single(4mm)
&Double
(8mm)
8.2
(0.323)
10.25
(0.404)
5.5±0.05
(0.217±0.002)
2.0±0.05(0.079±0.002)or
4.0±0.10(0.157±0.004)or
8.0±0.10(0.315±0.004)
4.6
(0.181)
12.3
(0.484)
1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment
location and hole location shall be applied independent of each other.
2. The tape, with or without components, shall pass around R without damage (see Figure 4).
3. If S1 < 1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Standard 481–D, paragraph 4.3, section b).
4. B1 dimension is a reference dimension for tape feeder clearance only.
5. The cavity de ned by A0, B0 and K0 shall surround the component with suffi cient clearance that:
(a) the component does not protrude above the top surface of the carrier tape.
(b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed.
(c) rotation of the component is limited to 20° maximum for 8 and 12 mm tapes (see Figure 2).
(d) lateral movement of the component is restricted to 0.5 mm maximum for 8 mm and 12 mm wide tape (see Figure 3).
(e) see Addendum in EIA Standard 481–D for standards relating to more precise taping requirements.
14© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard T2001_T409 • 8/27/2018
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
14
Tantalum Surface Mount Capacitors – MIL-PRF (CWR Style)
T409 MIL-PRF-55365/4 (CWR09 Style)
Packaging Information Performance Notes
1. Cover Tape Break Force: 1.0 kg minimum.
2. Cover Tape Peel Strength: Thetotalpeelstrengthofthecovertapefromthecarriertapeshallbe:
Tape Width Peel Strength
8 mm 0.1to1.0Newton(10to100gf)
12 and 16 mm 0.1to1.3Newton(10to130gf)
Thedirectionofthepullshallbeoppositethedirectionofthecarriertapetravel.Thepullangleofthecarriertapeshallbe
165°to180°fromtheplaneofthecarriertape.Duringpeeling,thecarrierand/orcovertapeshallbepulledatavelocityof
300 ±10 mm/minute.
3. Labeling:Barcodelabeling(standardorcustom)shallbeonthesideofthereeloppositethesprocketholes.Refer to EIA
Standards 556 and 624.
Figure 2 – Maximum Component Rotation
Ao
Bo
°
T
°
s
Maximum Component Rotation
Top View
Maximum Component Rotation
Side View
Tape
Width (mm)
Maximum
Rotation (°
T)
8, 12 20 Tape
Width (mm)
Maximum
Rotation (
8, 12 20
°
S)
Typical Pocket Centerline
Typical Component Centerline
Figure 3 – Maximum Lateral Movement
0.5 mm maximum
0.5 mm maximum
8 mm & 12 mm Tape
Figure 4 – Bending Radius
RR
Bending
Radius
Embossed
Carrier
Punched
Carrier
15© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard T2001_T409 • 8/27/2018
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
15
Tantalum Surface Mount Capacitors – MIL-PRF (CWR Style)
T409 MIL-PRF-55365/4 (CWR09 Style)
Figure 5 – Reel Dimensions
AD(See Note)
Full Radius,
See Note
B(see Note)
Access Hole at
Slot Location
(Ø 40 mm minimum)
If present,
tape slot in core
for tape start:
2.5 mm minimum width x
10.0 mm minimum depth
W3(Includes
flange distortion
at outer edge)
W2(Measured at hub)
W1(Measured at hub)
C
(Arbor hole
diameter)
Note: Drive spokes optional; if used, dimensions B and D shall apply.
N
Table 5 – Reel Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
Tape Size A B Minimum C DMinimum
8 mm
178±0.20
(7.008±0.008)
or
330±0.20
(13.000±0.008)
1.5
(0.059)
13.0+0.5/−0.2
(0.521+0.02/−0.008)
20.2
(0.795)
12 mm
Variable Dimensions — Millimeters (Inches)
Tape Size N Minimum W1 W2 Maximum W3
8 mm 50
(1.969)
8.4+1.5/−0.0
(0.331+0.059/−0.0)
14.4
(0.567)
Shall accommodate tape
widthwithoutinterference
12 mm
12.4+2.0/−0.0
(0.488+0.078/−0.0)
18.4
(0.724)
16© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard T2001_T409 • 8/27/2018
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
16
Tantalum Surface Mount Capacitors – MIL-PRF (CWR Style)
T409 MIL-PRF-55365/4 (CWR09 Style)
Figure 6 – Tape Leader & Trailer Dimensions
Trailer
160 mm minimum
Carrier Tape
END START
Round Sprocket Holes
Elongated Sprocket Holes
(32 mm tape and wider)
Top Cover Tape
Top Cover Tape
Punched Carrier
8 mm & 12 mm only
Embossed Carrier
Components
100 mm
minimum Leader
400 mm minimum
Figure 7 – Maximum Camber
Carrier Tape
Round Sprocket Holes
2 mm maximum, either direction for 8 mm wide tape
Straight Edge
250 mm
Elongated Sprocket Holes
(32 mm and wider tapes)
17© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard T2001_T409 • 8/27/2018
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
17
Tantalum Surface Mount Capacitors – MIL-PRF (CWR Style)
T409 MIL-PRF-55365/4 (CWR09 Style)
KEMET Electronics Corporation Sales Offi ces
Foracompletelistofourglobalsalesoces,pleasevisitwww.kemet.com/sales.
Disclaimer
Allproductspecications,statements,informationanddata(collectively,the“Information”)inthisdatasheetaresubjecttochange.Thecustomerisresponsible
forcheckingandverifyingtheextenttowhichtheInformationcontainedinthispublicationisapplicabletoanorderatthetimetheorderisplaced.AllInformation
givenhereinisbelievedtobeaccurateandreliable,butitispresentedwithoutguarantee,warranty,orresponsibilityofanykind,expressedorimplied.Statements
ofsuitabilityforcertainapplicationsarebasedonKEMETElectronicsCorporation’s(“KEMET”)knowledgeoftypicaloperatingconditionsforsuchapplications,but
arenotintendedtoconstitute–andKEMETspecicallydisclaims–anywarrantyconcerningsuitabilityforaspeciccustomerapplicationoruse.TheInformation
isintendedforuseonlybycustomerswhohavetherequisiteexperienceandcapabilitytodeterminethecorrectproductsfortheirapplication.Anytechnicaladvice
inferredfromthisInformationorotherwiseprovidedbyKEMETwithreferencetotheuseofKEMET’sproductsisgivengratis,andKEMETassumesnoobligationor
liabilityfortheadvicegivenorresultsobtained.
AlthoughKEMETdesignsandmanufacturesitsproductstothemoststringentqualityandsafetystandards,giventhecurrentstateoftheart,isolatedcomponent
failuresmaystilloccur.Accordingly,customerapplicationswhichrequireahighdegreeofreliabilityorsafetyshouldemploysuitabledesignsorothersafeguards
(suchastheinstallationofprotectivecircuitryorredundancies)inordertoensurethatthefailureofanelectricalcomponentdoesnotresultinariskofpersonal
injuryorpropertydamage.
Althoughallproduct-relatedwarnings,cautionsandnotesmustbeobserved,thecustomershouldnotassumethatallsafetymeasuresareindictedorthatother
measuresmaynotberequired.
KEMET is a registered trademark of KEMET Electronics Corporation.