CLD-DS113 Rev 1K Product family data sheet Cree(R) XLamp(R) MHD-G LEDs Product Description FEATURES Table of Contents The XLamp(R) MHD-G LED is a new * Flexible 18V or 36V options Characteristics........................................... 2 generation of highpower LED that * Maximum drive current: 1000 mA Flux Characteristics, EasyWhite(R) Order (18 V), 500 mA (36 V) Codes and Bins.......................................... 3 lowcost systems than midpower (MP) * Viewing angle: 115 Relative Spectral Power Distribution........ 5 LEDs. Built using Cree's highreliability * Available in 70CRI, 80CRI and 90CRI Relative Flux vs. Junction Temperature.... 5 options Electrical Characteristics........................... 6 delivers a more effective way to achieve ceramicpackage technology, the XLamp MHD-G LED is able to operate at higher * Unlimited floor life at 30 C/85% RH Relative Flux vs. Current............................ 7 temperatures than MP LEDs with no * Reflow solderable - JEDEC Relative Chromaticity vs. Current.............. 8 JSTD020C Relative Chromaticity vs. Temperature..... 9 reduction in rated lifetime, enabling an impressive 60% reduction in heat * Electrically neutral thermal path Typical Spatial Distribution........................ 9 sink size and cost. Using many times * RoHS and REACh compliant Thermal Design........................................ 10 fewer LEDs than MP LEDs to achieve * UL(R) recognized component (E349212) Performance Groups - Luminous Flux.. 11 the same performance, the XLamp Performance Groups - Chromaticity...... 11 MHD-G LED is optimized to simplify Cree's Standard White Chromaticity LED system designs for directional and Regions Plotted on the 1931 CIE Curve.. 12 semidirectional applications. Bin and Order Code Formats................... 13 Reflow Soldering Characteristics............ 14 Notes........................................................ 15 Mechanical Dimensions.......................... 17 Electrical Configuration........................... 19 Tape and Reel........................................... 20 www.cree.com/Xlamp Packaging................................................. 21 Copyright (c) 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), XLamp(R) and EasyWhite(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 XLamp (R) MHD-G LED Characteristics MHD-G 18V/36V LEDs are tested and binned in production in the 36V configuration. See the Mechanical Dimensions section on page 17 for pad layout options. Characteristics Unit Thermal resistance, junction to solder point C/W 2.6 degrees 115 Temperature coefficient of voltage (18 V)* mV/C -8.5 Temperature coefficient of voltage (36 V) mV/C -17 Viewing angle (FWHM) ESD withstand voltage (HBM per Mil-Std-883D) * Minimum Typical Maximum V 8000 DC forward current (18 V)* mA 1000 DC forward current (36 V) mA 500 Reverse current (18 V, 36 V)* mA -0.1 Forward voltage (18 V, @ 700 mA, 85 C)* V 18.2 20 Forward voltage (36 V, @ 350 mA, 85 C) V 36.4 40 LED junction temperature C 150 Data for the 18V configuration is calculated and for reference only. Copyright (c) 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), XLamp(R) and EasyWhite(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 2 XLamp (R) MHD-G LED Flux Characteristics, EasyWhite(R) Order Codes and Bins The following table provides order codes for XLamp MHD-G LEDs. For a complete description of the order code nomenclature, please see the Bin and Order Code Formats section (page 13). Test condition: TJ = 85 C, 36 V, IF = 350 mA Reference condition: TJ = 85 C, 18 V, IF = 700 mA Nominal CCT CRI Min 70 6500 K Minimum Luminous Flux 2-Step 3-Step Group Flux (lm) @ 85 C Flux (lm) @ 25 C* M2 1380 1559 M4 1485 1678 N2 1590 1796 MHDGWT-0000000N0BN265E M2 1380 1559 MHDGWT-0000000N0HM265E M4 1485 1678 MHDGWT-0000000N0HM465E M2 1380 1559 MHDGWT-0000000N0BM257E M4 1485 1678 N2 1590 1796 MHDGWT-0000000N0BN257E M2 1380 1559 MHDGWT-0000000N0BM250E M4 1485 1678 N2 1590 1796 M2 1380 1559 Group Order Code Group Order Code 70 70 5000 K Group 65E 65E 80 57E 50E MHDGWT-0000000N0BM465E MHDGWT-0000000N0BM457E MHDGWT-0000000N0BM450E MHDGWT-0000000N0BN250E 50G MHDGWT-0000000N0HM250G M4 1485 1678 MHDGWT-0000000N0HM450G K2 1200 1356 MHDGWT-0000000N0UK250G K4 1290 1457 90 Order Code MHDGWT-0000000N0BM265E 80 5700 K 5-Step 50G 50E MHDGWT-0000000N0HM250E MHDGWT-0000000N0HM450E MHDGWT-0000000N0UK450G Notes * Cree maintains a tolerance of 7% on flux and power measurements, 0.005 on chromaticity (CCx, CCy) measurements and a tolerance of 2 on CRI measurements. See the Measurements section (page 19). * Cree XLamp MHD-E LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code. * Flux values @ 25 C are calculated and for reference only. Copyright (c) 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), XLamp(R) and EasyWhite(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 3 XLamp (R) MHD-G LED Flux Characteristics, EasyWhite(R) Order Codes and Bins - Continued Nominal CCT CRI Min Minimum Luminous Flux Group Flux (lm) @ 85 C Flux (lm) @ 25 C* M2 1380 1559 2-Step Group Order Code 3-Step Group Order Code 70 4000 K M4 1485 1678 K4 1290 1457 M2 1380 1559 MHDGWT-0000000N0HM240H K2 1200 1356 MHDGWT-0000000N0UK240H K4 1290 1457 MHDGWT-0000000N0UK440H K2 1200 1356 MHDGWT-0000000N0HK235H K4 1290 1457 M2 1380 1559 MHDGWT-0000000N0HM235H MHDGWT-0000000N0HM235G J4 1120 1265 MHDGWT-0000000N0UJ435H MHDGWT-0000000N0UJ435G K2 1200 1356 MHDGWT-0000000N0UK235H K2 1200 1356 MHDGWT-0000000N0HK230H K4 1290 1457 M2 1380 1559 MHDGWT-0000000N0HM230H MHDGWT-0000000N0HM230G J4 1120 1265 MHDGWT-0000000N0UJ430H MHDGWT-0000000N0UJ430G K2 1200 1356 K2 1200 1356 40H 90 3500 K 40H 90 80 3000 K Group 40E 80 80 5-Step 35H 35H 90 30H 30H 80 27H MHDGWT-0000000N0HK440H MHDGWT-0000000N0HK435H MHDGWT-0000000N0HK430H MHDGWT-0000000N0UK230H MHDGWT-0000000N0HK227H K4 1290 1457 MHDGWT-0000000N0HK427H J2 1040 1175 MHDGWT-0000000N0UJ227H J4 1120 1265 2700 K 90 27H MHDGWT-0000000N0UJ427H 40G 40G Order Code MHDGWT-0000000N0BM240E MHDGWT-0000000N0BM440E MHDGWT-0000000N0HK440G MHDGWT-0000000N0HM240G MHDGWT-0000000N0UK240G MHDGWT-0000000N0UK440G MHDGWT-0000000N0HK235G 35G 35G MHDGWT-0000000N0HK435G MHDGWT-0000000N0UK235G MHDGWT-0000000N0HK230G 30G 30G 27G 27G MHDGWT-0000000N0HK430G MHDGWT-0000000N0UK230G MHDGWT-0000000N0HK227G MHDGWT-0000000N0HK427G MHDGWT-0000000N0UJ227G MHDGWT-0000000N0UJ427G Notes * Cree maintains a tolerance of 7% on flux and power measurements, 0.005 on chromaticity (CCx, CCy) measurements and a tolerance of 2 on CRI measurements. See the Measurements section (page 19). * Cree XLamp MHD-E LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code. * Flux values @ 25 C are calculated and for reference only. Copyright (c) 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), XLamp(R) and EasyWhite(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 4 XLamp (R) MHD-G LED Relative Spectral Power Distribution Relative Spectral Power Distribution 100% 90% Relative Spectral Power 80% 70% 60% 6500 K, 80 CRI 50% 5000 K, 80 CRI 40% 3000 K, 80 CRI 30% 20% 10% 0% 380 430 480 530 580 630 680 730 780 Wavelength (nm) Relative Flux Output vs. Junction Temperature Relative Flux vs. Junction Temperature Test condition: 18 V (for reference), If = 700 mA; 36 V, IF = 350 mA 120% Relative Luminous Flux 100% 80% 60% 40% 20% 0% 25 50 75 100 125 150 Junction Temperature (C) Copyright (c) 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), XLamp(R) and EasyWhite(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 5 XLamp (R) MHD-G LED Electrical Characteristics (TJ = 85 C) 1000 Forward Current (mA) 900 800 700 600 500 18 V 400 300 200 100 0 Electrical Characteristics 16.0 (Tj = 85C) 16.5 17.0 17.5 18.0 18.5 19.0 Forward Voltage (V) 500 450 Forward Current (mA) 400 350 300 250 36 V 200 150 100 50 0 32 33 34 35 36 37 38 Forward Voltage (V) Copyright (c) 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), XLamp(R) and EasyWhite(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 6 XLamp (R) MHD-G LED Relative Flux vs. Current (TJ = 85 C) 140% Relative Luminous Flux 120% 100% 80% 18 V 60% 40% 20% 0% 0 100 200 300 Relative Intensity vs. Current (Tj = 85C) 400 500 600 700 800 900 1000 Forward Current (mA) 140% Relative Luminous Flux 120% 100% 80% 36 V 60% 40% 20% 0% 0 50 100 150 200 250 300 350 400 450 500 Forward Current (mA) Copyright (c) 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), XLamp(R) and EasyWhite(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 7 XLamp (R) MHD-G LED Relative Chromaticity vs. Current (Warm White) 0.015 18 V 0.010 0.005 CCx 0.000 CCy -0.005 -0.010 -0.015 100 200 300 400 500 600 700 800 900 1000 Current (mA) 0.015 36 V 0.010 0.005 CCx 0.000 CCy -0.005 -0.010 -0.015 50 100 150 200 250 300 350 400 450 500 Current (mA) Copyright (c) 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), XLamp(R) and EasyWhite(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 8 XLamp (R) MHD-G LED Relative Chromaticity vs. Temperature (Warm White) Test condition: 18 V (for reference), If = 700 mA; 36 V, IF = 350 mA 0.015 0.010 0.005 CCx 0.000 CCy -0.005 -0.010 -0.015 25 50 75 100 125 150 Tsp (C) Typical Spatial Distribution Far Field Test condition: 18 V (for reference), If = 700 mA; 36 V, IF = 350 mA 100% Relative Luminous Intensity 80% 60% 40% 20% -90 -70 -50 -30 -10 0% 10 30 50 70 90 Angle () Copyright (c) 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), XLamp(R) and EasyWhite(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 9 XLamp (R) MHD-G LED Thermal Design The maximum forward current is determined by the thermal resistance between the LED junction and ambient. It is crucial for the end product to be designed in a manner that minimizes the thermal resistance from the solder point to ambient in order to optimize lamp life and optical characteristics. 1100 1000 18 V Maximum Current (mA) 900 800 700 600 500 400 Rj-a = 4 C/W 300 Rj-a = 5 C/W 200 Rj-a = 6 C/W 100 Rj-a = 7 C/W 0 0 20 40 60 80 100 120 140 160 Ambient Temperature (C) Thermal Design 550 500 36 V Maximum Current (mA) 450 400 350 300 250 200 Rj-a = 4 C/W 150 Rj-a = 5 C/W 100 Rj-a = 6 C/W 50 Rj-a = 7 C/W 0 0 20 40 60 80 100 120 140 160 Ambient Temperature (C) Copyright (c) 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), XLamp(R) and EasyWhite(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 10 XLamp (R) MHD-G LED Performance Groups - Luminous Flux (TJ = 85 C) XLamp MHD-G LEDs are tested for luminous flux and placed into one of the following bins. Group Code Minimum Luminous Flux Maximum Luminous Flux J2 1040 1120 J4 1120 1200 K2 1200 1290 K4 1290 1380 M2 1380 1485 M4 1485 1590 N2 1590 1710 N4 1710 1830 Performance Groups - Chromaticity XLamp MHD-G LEDs are tested for chromaticity and placed into one of the regions defined by the following bounding coordinates. EasyWhite Color Temperatures - 2-Step Code 40H 35H 30H 27H CCT 4000 K 3500 K 3000 K 2700 K x y 0.3777 0.3739 0.3797 0.3816 0.3861 0.3855 0.3838 0.3777 0.4022 0.3858 0.4053 0.3942 0.4125 0.3977 0.4091 0.3891 0.4287 0.3975 0.4328 0.4064 0.4390 0.4086 0.4347 0.3996 0.4524 0.4048 0.4574 0.4140 0.4633 0.4154 0.4581 0.4062 Copyright (c) 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), XLamp(R) and EasyWhite(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 11 XLamp (R) MHD-G LED Performance Groups - Chromaticity (Tj = 85 C) - Continued EasyWhite Color Temperatures - 3-Step Ellipse Major Axis Minor Axis x y a b Rotation Angle () 5000 K 0.3447 0.3553 0.00840 0.00312 65.0 4000 K 0.3818 0.3797 0.00939 0.00402 53.7 35G 3500 K 0.4073 0.3917 0.00927 0.00414 53.2 30G 3000 K 0.4338 0.4030 0.00834 0.00408 53.2 27G 2700 K 0.4577 0.4099 0.00834 0.00420 48.5 Major Axis Minor Axis y a b Rotation Angle () Bin Code CCT 50G 40G Center Point EasyWhite Color Temperatures - 5-Step Ellipse Bin Code Center Point CCT x 65E 6500 K 0.3123 0.3282 0.01110 0.00550 61.0 57E 5700 K 0.3287 0.3417 0.01230 0.00600 72.0 50E 5000 K 0.3447 0.3553 0.01400 0.00520 65.0 40E 4000 K 0.3818 0.3797 0.01565 0.00670 53.7 Cree's Standard White Chromaticity Regions Plotted on the 1931 CIE Curve 0.44 ANSI C78.377 Quadrangle 0.43 EasyWhite 5-Step 0.42 EasyWhite 3-Step 0.41 EasyWhite 2-Step 2700 K 3000 K 3500 K 4000 K 0.40 4500 K 0.39 5000 K 0.38 CCy 0.37 5700 K 0.36 6500 K 0.35 0.34 8000 K 0.33 0.32 0.31 0.30 0.29 0.49 0.48 0.47 0.46 0.45 0.44 0.43 0.42 0.41 0.40 0.39 0.38 0.37 0.36 0.35 0.34 0.33 0.32 0.31 0.30 0.29 0.28 0.27 0.28 CCx Copyright (c) 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), XLamp(R) and EasyWhite(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 12 XLamp (R) MHD-G LED Bin and Order Code Formats Bin codes and order codes for MHD-G LEDs are configured in the following manner: Order Code Bin Code Series MHDG = MHD-G Series MHDG = MHD-G Internal code Chromaticity bin CRI Specification B = 70 CRI minimum H = 80 CRI minimum U = 90 CRI minimum Vf class N0 = 18-V/36-V class Chromaticity region SSSSCC-HHHH-HHHGGNFFDDD Flux Vf class N0 = 18-V/36-V class Color WT = White Internal code SSSSCC-WWW-FF-GGN-AAAAA CRI Specification B = 70 CRI minimum H = 80 CRI minimum U = 90 CRI minimum Flux bin Color WT = White Copyright (c) 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), XLamp(R) and EasyWhite(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 13 XLamp (R) MHD-G LED Reflow Soldering Characteristics In testing, Cree has found XLamp MHD-G LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of the solder paste used, and therefore it is the lamp or luminaire manufacturer's responsibility to determine applicable soldering requirements. Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment. tP TP Critical Zone TL to TP Temperature Ramp-up TL tS Tsmax Tsmin Ramp-down ts Preheat 25 t 25C to Peak Profile Feature Average Ramp-Up Rate (Tsmax to Tp) Time Lead-Free Solder 1.2 C/second Preheat: Temperature Min (Tsmin) 120 C Preheat: Temperature Max (Tsmax) 170 C Preheat: Time (tsmin to tsmax) 65-150 seconds Time Maintained Above: Temperature (TL) Time Maintained Above: Time (tL) 217 C 45-90 seconds Peak/Classification Temperature (Tp) 235 - 245 C Time Within 5 C of Actual Peak Temperature (tp) 20-40 seconds Ramp-Down Rate 1 - 6 C/second Time 25 C to Peak Temperature 4 minutes max. Note: All temperatures refer to the topside of the package, measured on the package body surface. Copyright (c) 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), XLamp(R) and EasyWhite(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 14 XLamp (R) MHD-G LED Notes Measurements The luminous flux, radiant power, chromaticity, forward voltage and CRI measurements in this document are binning specifications only and solely represent product measurements as of the date of shipment. These measurements will change over time based on a number of factors that are not within Cree's control and are not intended or provided as operational specifications for the products. Calculated values are provided for informational purposes only and are not intended or provided as specifications. PreRelease Qualification Testing Please read the LED Reliability Overview for details of the qualification process Cree applies to ensure long-term reliability for XLamp LEDs and details of Cree's pre-release qualification testing for XLamp LEDs. Lumen Maintenance Cree now uses standardized IES LM-80-08 and TM-21-11 methods for collecting long-term data and extrapolating LED lumen maintenance. For information on the specific LM-80 data sets available for this LED, refer to the public LM-80 results document. Please read the Long-Term Lumen Maintenance application note for more details on Cree's lumen maintenance testing and forecasting. Please read the Thermal Management application note for details on how thermal design, ambient temperature, and drive current affect the LED junction temperature. Moisture Sensitivity Cree recommends keeping XLamp LEDs in the provided, resealable moisture-barrier packaging (MBP) until immediately prior to soldering. Unopened MBPs that contain XLamp LEDs do not need special storage for moisture sensitivity. Once the MBP is opened, XLamp MHD-G LEDs may be stored as MSL 1 per JEDEC J-STD-033, meaning they have unlimited floor life in conditions of 30 C/85% relative humidity (RH). Regardless of the storage condition, Cree recommends sealing any unsoldered LEDs in the original MBP. RoHS Compliance The levels of RoHS restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2011/65/EC (RoHS2), as implemented January 2, 2013. RoHS Declarations for this product can be obtained from your Cree representative or from the Product Ecology section of the Cree website. REACh Compliance REACh substances of very high concern (SVHCs) information is available for this product. Since the European Chemical Agency (ECHA) has published notice of their intent to frequently revise the SVHC listing for the foreseeable future, please contact a Cree representative to insure you get the most up-to-date REACh Declaration. REACh banned substance information (REACh Article 67) is also available upon request. Copyright (c) 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), XLamp(R) and EasyWhite(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 15 XLamp (R) MHD-G LED Notes - Continued UL(R) Recognized Component This product meets the requirements to be considered a UL Recognized Component with Level 4 enclosure consideration. The LED package or a portion thereof has been investigated as a fire and electrical enclosure per ANSI/UL 8750. Vision Advisory WARNING: Do not look at an exposed lamp in operation. Eye injury can result. For more information about LEDs and eye safety, please refer to the LED Eye Safety application note. Copyright (c) 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), XLamp(R) and EasyWhite(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 16 XLamp (R) MHD-G LED Mechanical Dimensions Thermal vias, if present, are not shown on these drawings. All measurements 6.70 are .13 mm unless otherwise indicated. 7.00 .50 6.70 REF. 4.30 .35 0.2 mm 7.00 6.70 6.70 REF. .80 2.95 .71 0.75 0.2 mm OPTICAL REFERENCE Top View 6.700 6.700 .700 .700 3.900 .50 7.00 Anode Side 6.70 6.70 .50 .70 4.30 .70 6.760 6.760 6.70 .80 6.70 2.95 6.70 .700 .700 3.900 6.76 Side View 6.70 .70 .70 6.70 REF. Anode Cathode Side 6.70 REF. Side 6.76 6.76 .70 1.24 1.29 .25 .25 .25 .25 6.70 REF. .80 Bottom View PRIMARY .70 ALTERNATIVE 1.29 6.70 REF. 1.29 2.95 REFERENCE 6.700 3.900 Cathode Side 4.30 6.70 PRIMARY .70 1.24 .700 1.29 .700 .700 .700 .35 mm 00 OPTICAL REFERENCE .70 1.24 1.29 .25 6.70 .70 .70 PRIMARY ALTERNATIVE Alternate Bottom View ALTERNATIVE .70 1.24 1.29 .25 6.76 .25 1.29 .25 1.29 Copyright (c) 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), XLamp(R) and EasyWhite(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 17 D .35 0.2 mm .70 0.75 .71mm 0.2 7.000.2 mm D 4.30 REF. 4.30 .71 .35 0.2 mm 7.00 6.70 7.00 XLamp (R) MHD-G LED .80 6.70 6 R .80 2.95 2.95 Mechanical Dimensions - Continued C C 18V Configuration PRIMARY 6.70 .70 .70 .70 B .70 .70 5 1.24 .70 .70 1.29 5 1.24 4 4 .25 NOTICE NOTICECREE CONFIDENTIAL. 3.90 THIS PLOT AND THE INFORMATION 3.90 CREE CONFIDENTIAL. THIS PLOTCONTAINED AND THE INFORMATION WITHIN ARE THE PROPRIETARY AND CONTAINED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONFIDENTIAL INFORMATION OF CREE, INC. PLOT MAY NOT BE THIS COPIED, REPRODUCED OR DISCLOSED TO ANY MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT OF CREE INC. OF CREE INC. 1.29 7.00 6.76 6.76 RECOMMENDED (HATCHED AREA 2.95 RECOMMENDED PCB SOLDER PAD RECOMMENDED PCB SOLDER PAD 36V Configuration 6 .71 5 6 5 0.75 0.2mm 6.70 6.70 Recommended Stencil Pattern (Shaded Area Is Open) 4 6.70 .70 .70 PRIMARY B 6.76 .50 6.76 .50 3 6.70 .70 .70 1.24 PRIMARY A Fax (919) 7x7 MHD-E 9V/36V 7x7 MHD-G 18V MATERIAL SIZE C SCALE DRAWING NO. 2610-00051-OUTLIN SIZE FINAL PROTECTIVE FINISH C SHEET 15.000 SCALE 1.6 ALTERNATIVE 15.000 1 ALTERNAT 2 6.76 .25 3.13 3.13 1.29 ALL DIMENSIONS ARE .13mm UNLESS OTH ALL DIMENSIONS ARE .13mm UNLESS OTHERWISE NOTED .70 .70 RECOMMENDED STENCIL PATTERN RECOMMENDED STENCIL PATTERN (HATCHED AREA IS OPENING) (HATCHED AREA IS OPENING) RECOMMENDED PCB SOLDER PAD RECOMMENDED PCB SOLDER PAD Recommended PCB Solder Pad 6 Phone (9 DATE .70 .70 A APPROVED TITLE FOR SHEET METAL PARTS ONLY .X 1.5 .XX .75 .XXX .25 X .5 SURFACE FINISH: 2 11/12/14 DATE 1.24 1.29 .70 D. CRONIN TITLE 4600 Silic Durham, DATE DRAWN BY CHECK FINAL PROTECTIVE FINISH 3 .25 3.13 DATE D. CRONIN 11/12/14 UNLESS OTHERWISE SPECIFIED DATE DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. APPROVED TOLERANCE UNLESSDATE SPECIFIED: .XX .25 .XXX .125 MATERIAL X .5 CHECK .50 .50 6.76 3.13 .13mm UNLESS OTHERWISE NOTED 6.70DIMENSIONS ARE ALL .13mm UNLESS OT DRAWN BY 1.29 .25 1.29 .25 B 1.6 SURFACE FINISH: 4 0.75 0.2mm .70 ALL DIMENSIONS ARE 6.70 .71 .70 .70 1.29 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN STENCIL PATTERN MILLIMETERS AND AFTER FINISH. IS OPEN)RECOMMENDED STENCIL PATTERNTOLERANCE UNLESS SPECIFIED: .XX .25 (HATCHED AREA IS OPEN) 2.95 .XXX .125 X .5 THIRD ANGLE PROJECTION FOR SHEET METAL PARTS ONLY THIRD ANGLE PROJECTION .X 1.5 .XX .75 .XXX .25 X .5 C C 6.70 REF. .25 .80 .80 Recommended PCB Solder Pad A A .25 1.29 7.00 7.00 DESCRIPTION BY 6.70 REF. .70 4.30 4.30 .35 0.2mm .35 0.2mm .50 .70 6.76 1 REVIS REVISONS REV DESCRIPTION 6.70 .50 6.76 2 2 REV 6.70 D D 3 3 .25 B 7.00 ALTERNA 6.70 .70 .70 .70 6 6 6.70 6.70 ALTERNATIVE PRIMARY 6 5 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX .25 .XXX .125 THIRD ANGLE X PROJECTION .5 Recommended Stencil Pattern (Shaded Area Is Open) THIRD ANGLE PROJECTION 5 4 4 FOR SHEET METAL PARTS ONLY .X 1.5 .XX .75 .XXX .25 X .5 SURFACE FINISH: 3 1.6 3 UNLESS SPECIFIED DRAWN BYOTHERWISEDATE DIMENSIONS ARE IN D. CRONIN 11/17/14 MILLIMETERS AND AFTER FINISH. CHECK DATE TOLERANCE UNLESS SPECIFIED: .XX .25 APPROVED .XXX DATE .125 X .5 FOR SHEET METAL PARTS ONLY MATERIAL .X 1.5 .XX .75 .XXX .25 FINAL PROTECTIVE FINISH X .5 SURFACE FINISH: 2 1.6 DATE DRAWN BY D. CRONIN 11/17/14 CHECK DATE APPROVED DATE 4600 S Durham Phone Fax (91 TITLE TITLE MATERIAL 7x7 MHD-E 18V 7x7 MHD-G 36V SIZE SIZE SCALE C 2610-00052-OUTL DRAWING NO. FINAL PROTECTIVE FINISH C 15.000 SCALE 15.00 SHEET 2 Copyright (c) 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), XLamp(R) and EasyWhite(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 18 1 POSITIVE (+) XLamp (R) MHD-G LED NEGATIVE (-) Electrical Configuration 36 V 18 V NEGATIVE (-) POSITIVE (+) NEGATIVE (-) POSITIVE (+) SOLDER PAD LINK POSITIVE (+) NEGATIVE (-) 18-V Configuration 36-V Configuration 18 V NEGATIVE (-) POSITIVE (+) NEGATIVE (-) POSITIVE (+) Copyright (c) 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), XLamp(R) and EasyWhite(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 19 XLamp (R) MHD-G LED Tape and Reel All Cree carrier tapes conform to EIA-481D, Automated Component Handling Systems Standard. All measurements are .13 mm unless otherwise indicated. 2.00 [.079] P2 +.0039 1.50+.10 -.00 [ .0591-.0000 ] Do 4.00 [.157] Po 1.75 [.069] E1 CATHODE SIDE 3.0 7.50 [.295]F 1.50 [.059] D1 MIN 12.00 [.472] P NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTANED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT OF CREE INC. 5 7.60 [.299] Bo ANODE SIDE .30 [.012] T 3.0 6 16.00 [.630] NOMINAL 14.25 [.561] 16.30 [.642] MAX E2 W 4 1.70 [.067] Ko 3 2 1000 LEDs per reel 7.60 [.299] 1 2400-00009 INDEX QTY ITEM COMMENTS 1 2 1 2 2400-00009-CORE 2400-00009-REEL D D 12.4 +.2 .0 MEASURED AT HUB C 330 +.25 -.75 C 16.4 +0.2 .0 MEASURED AT HUB 1.9.4 21 .4 13.1 .2 B B 12.4 +1.0 -.5 MEASURED AT EDGE 60 60 REVISONS REV DESCRIPTION DRAWN BY A BY DATE APP'D Copyright (c) 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), XLamp(R) and EasyWhite(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. UNLESS OTHERWISE SPECIFIED THIRD ANGLE PROJECTION DIMENSIONS ARE IN INCHES AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX .01 .XXX .005 X .5 FOR SHEET METAL PARTS ONLY D. CRONIN CHECK DATE 4600 Silicon Drive Durham, N.C 27703 09/29/09 20 DATE -APPROVED -MATERIAL Phone (919) 313-5300 -- Fax (919) 313-5558 DATE -- TITLE REEL, 13" X 12MM, 3 PIECE SNAP A XLamp (R) MHD-G LED Packaging Humidity Indicator Card (inside bag) Dessicant (inside bag) Unpackaged Reel Label with Cree Bin Code, Quantity, Reel ID Packaged Reel Label with Cree Bin Code, Qty, Lot # Vacuum-Sealed Moisture Barrier Bag Label with Cree Order Code, Quantity, Reel ID, PO # Label with Cree Bin Code, Quantity, Reel ID Label with Custo Code, Qty, Reel I Boxed Reel Label with Cree Order Code, Quantity, Reel ID, PO # Patent Label Label with Cree Bin Code, Quantity, Reel ID Patent Label Copyright (c) 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), XLamp(R) and EasyWhite(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 21 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Cree, Inc.: MHDGWT-0000-000N0HK235G MHDGWT-0000-000N0HM230G MHDGWT-0000-000N0HK430G MHDGWT-0000000N0HK440G MHDGWT-0000-000N0HK227G MHDGWT-0000-000N0HK230G MHDGWT-0000-000N0HK435G MHDGWT-0000-000N0HM235G MHDGWT-0000-000N0HK427G MHDGWT-0000-000N0HM227G MHDGWT-0000000N0HM450E MHDGWT-0000-000N0HM250E MHDGWT-0000-000N0HM240G MHDGWT-0000-000N0HK435H MHDGWT-0000-000N0HK430H MHDGWT-0000-000N0UJ430H MHDGWT-0000-000N0UJ227G MHDGWT-0000000N0BM457E MHDGWT-0000-000N0UJ227H MHDGWT-0000-000N0UK230H MHDGWT-0000-000N0BM440E MHDGWT-0000-000N0HK427H MHDGWT-0000-000N0HM235H MHDGWT-0000-000N0UK240H MHDGWT-0000000N0HM230H MHDGWT-0000-000N0HM265E MHDGWT-0000-000N0HM457E MHDGWT-0000-000N0UK450E MHDGWT-0000-000N0UK240G MHDGWT-0000-000N0UK450G MHDGWT-0000-000N0UJ435H MHDGWT-0000000N0UJ435G MHDGWT-0000-000N0BM240E MHDGWT-0000-000N0UK250G MHDGWT-0000-000N0UK235H MHDGWT-0000-000N0BM450E MHDGWT-0000-000N0BM465E MHDGWT-0000-000N0BM250E MHDGWT-0000000N0UK235G MHDGWT-0000-000N0HM257E MHDGWT-0000-000N0HM465E MHDGWT-0000-000N0UK230G MHDGWT-0000-000N0UJ427H MHDGWT-0000-000N0HM250G MHDGWT-0000-000N0BN257E MHDGWT-0000000N0BM257E MHDGWT-0000-000N0BM265E MHDGWT-0000-000N0HM227H MHDGWT-0000-000N0UJ427G MHDGWT-0000-000N0HM240H MHDGWT-0000-000N0UK440H MHDGWT-0000-000N0HK440H MHDGWT-0000000N0UK440G MHDGWT-0000-000N0UK250E MHDGWT-0000-000N0HM450G MHDGWT-0000-000N0BN265E MHDGWT-0000-000N0UK227G MHDGWT-0000-000N0UJ430G MHDGWT-0000-000N0HK230H MHDGWT-0000000N0HK235H MHDGWT-0000-000N0BN250E MHDGWT-0000-000N0HK227H MHDGWT-0000-000N0UK227H