Product family data sheet
Copyright © 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and
EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
Cree, Inc.
4600 Silicon Drive
Durham, NC 27703
USA Tel: +1.919.313.5300
WWW.CREE.COM/XLAMP
CLD-DS113 REV 1K
Cree® XLamp® MHD-G LEDs
PRODUCT DESCRIPTION
The XLamp® MHD-G LED is a new
generation of high-power LED that
delivers a more effective way to achieve
low-cost systems than mid-power (MP)
LEDs. Built using Crees high-reliability
ceramic-package technology, the XLamp
MHD-G LED is able to operate at higher
temperatures than MP LEDs with no
reduction in rated lifetime, enabling
an impressive 60% reduction in heat
sink size and cost. Using many times
fewer LEDs than MP LEDs to achieve
the same performance, the XLamp
MHD-G LED is optimized to simplify
LED system designs for directional and
semi-directional applications.
FEATURES
• Flexible 18-V or 36-V options
• Maximumdrivecurrent:1000mA
(18V),500mA(36V)
• Viewingangle:115°
• Availablein70‑CRI,80‑CRIand90‑CRI
options
• Unlimitedoorlifeat≤30ºC/85%RH
• Reowsolderable‑JEDEC
J‑STD‑020C
• Electrically neutral thermal path
• RoHSandREAChcompliant
• UL®recognizedcomponent(E349212)
TABLE OF CONTENTS
Characteristics .......................................... 2
Flux Characteristics, EasyWhite® Order
Codes and Bins ......................................... 3
Relative Spectral Power Distribution ....... 5
RelativeFluxvs.JunctionTemperature ... 5
Electrical Characteristics .......................... 6
Relative Flux vs. Current ........................... 7
Relative Chromaticity vs. Current ............. 8
Relative Chromaticity vs. Temperature .... 9
Typical Spatial Distribution ....................... 9
Thermal Design ....................................... 10
Performance Groups – Luminous Flux.. 11
Performance Groups – Chromaticity ..... 11
Crees Standard White Chromaticity
RegionsPlottedonthe1931CIECurve . 12
Bin and Order Code Formats .................. 13
ReowSolderingCharacteristics ........... 14
Notes ....................................................... 15
Mechanical Dimensions ......................... 17
ElectricalConguration .......................... 19
Tape and Reel .......................................... 20
Packaging ................................................ 21
Copyright © 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a
trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
2
XLamp® mHD-G LED
CHARACTERISTICS
MHD‑G18‑V/36‑VLEDsaretestedandbinnedinproductioninthe36‑Vconguration.SeetheMechanicalDimensionssectiononpage
17forpadlayoutoptions.
Characteristics Unit Minimum Typical Maximum
Thermal resistance, junction to solder point °C/W 2.6
Viewing angle (FWHM) degrees 115
Temperaturecoefcientofvoltage(18V)* mV/°C ‑8.5
Temperaturecoefcientofvoltage(36V) mV/°C ‑17
ESD withstand voltage (HBM per Mil-Std-883D) V 8000
DCforwardcurrent(18V)* mA 1000
DCforwardcurrent(36V) mA 500
Reversecurrent(18V,36V)* mA -0.1
Forwardvoltage(18V,@700mA,85°C)* V18.2 20
Forwardvoltage(36V,@350mA,85°C) V 36.4 40
LED junction temperature °C 150
* Dataforthe18‑Vcongurationiscalculatedandforreferenceonly.
Copyright © 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a
trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
3
XLamp® mHD-G LED
Notes
• Cree maintains a tolerance of ±7% on ux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and a
toleranceof±2onCRImeasurements.SeetheMeasurementssection(page19).
• CreeXLampMHD‑ELEDordercodesspecifyonlyaminimumuxbinandnotamaximum.Creemayshipreelsinuxbinshigherthan
theminimumspeciedbytheordercodewithoutadvancenotice.Shipmentswillalwaysadheretothechromaticitybinrestrictions
speciedbytheordercode.
* Fluxvalues@25°Carecalculatedandforreferenceonly.
FLUX CHARACTERISTICS, EASYWHITE® ORDER CODES AND BINS
The following table provides order codes for XLamp MHD-G LEDs. For a complete description of the order code nomenclature, please see
the Bin and Order Code Formats section (page 13).
Test condition: TJ=85°C,36V,IF=350mA
Reference condition: TJ=85°C,18V,IF=700mA
Nominal
CCT
CRI Minimum Luminous Flux 2-Step 3-Step 5-Step
Min Group Flux (lm)

Flux (lm)
 Group Order Code Group Order Code Group Order Code
6500K
70
M2 1380 1559
65E
MHDGWT-0000-
000N0BM265E
M4 1485 1678 MHDGWT-0000-
000N0BM465E
N2 1590 1796 MHDGWT-0000-
000N0BN265E
80
M2 1380 1559
65E
MHDGWT-0000-
000N0HM265E
M4 1485 1678 MHDGWT-0000-
000N0HM465E
5700K 70
M2 1380 1559
57E
MHDGWT-0000-
000N0BM257E
M4 1485 1678 MHDGWT-0000-
000N0BM457E
N2 1590 1796 MHDGWT-0000-
000N0BN257E
5000K
70
M2 1380 1559
50E
MHDGWT-0000-
000N0BM250E
M4 1485 1678 MHDGWT-0000-
000N0BM450E
N2 1590 1796 MHDGWT-0000-
000N0BN250E
80
M2 1380 1559
50G
MHDGWT-0000-
000N0HM250G 50E
MHDGWT-0000-
000N0HM250E
M4 1485 1678 MHDGWT-0000-
000N0HM450G
MHDGWT-0000-
000N0HM450E
90
K2 1200 1356
50G
MHDGWT-0000-
000N0UK250G
K4 1290 1457 MHDGWT-0000-
000N0UK450G
Copyright © 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a
trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
4
XLamp® mHD-G LED
Notes
• Cree maintains a tolerance of ±7% on ux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and a
toleranceof±2onCRImeasurements.SeetheMeasurementssection(page19).
• CreeXLampMHD‑ELEDordercodesspecifyonlyaminimumuxbinandnotamaximum.Creemayshipreelsinuxbinshigherthan
theminimumspeciedbytheordercodewithoutadvancenotice.Shipmentswillalwaysadheretothechromaticitybinrestrictions
speciedbytheordercode.
* Fluxvalues@25°Carecalculatedandforreferenceonly.
Nominal
CCT
CRI Minimum Luminous Flux 2-Step 3-Step 5-Step
Min Group Flux (lm)

Flux (lm)
 Group Order Code Group Order Code Group Order Code
4000K
70
M2 1380 1559
40E
MHDGWT-0000-
000N0BM240E
M4 1485 1678 MHDGWT-0000-
000N0BM440E
80
K4 1290 1457
40H
MHDGWT-0000-
000N0HK440H 40G
MHDGWT-0000-
000N0HK440G
M2 1380 1559 MHDGWT-0000-
000N0HM240H
MHDGWT-0000-
000N0HM240G
90
K2 1200 1356
40H
MHDGWT-0000-
000N0UK240H 40G
MHDGWT-0000-
000N0UK240G
K4 1290 1457 MHDGWT-0000-
000N0UK440H
MHDGWT-0000-
000N0UK440G
3500K
80
K2 1200 1356
35H
MHDGWT-0000-
000N0HK235H
35G
MHDGWT-0000-
000N0HK235G
K4 1290 1457 MHDGWT-0000-
000N0HK435H
MHDGWT-0000-
000N0HK435G
M2 1380 1559 MHDGWT-0000-
000N0HM235H
MHDGWT-0000-
000N0HM235G
90
J4 1120 1265
35H
MHDGWT-0000-
000N0UJ435H 35G
MHDGWT-0000-
000N0UJ435G
K2 1200 1356 MHDGWT-0000-
000N0UK235H
MHDGWT-0000-
000N0UK235G
3000K
80
K2 1200 1356
30H
MHDGWT-0000-
000N0HK230H
30G
MHDGWT-0000-
000N0HK230G
K4 1290 1457 MHDGWT-0000-
000N0HK430H
MHDGWT-0000-
000N0HK430G
M2 1380 1559 MHDGWT-0000-
000N0HM230H
MHDGWT-0000-
000N0HM230G
90
J4 1120 1265
30H
MHDGWT-0000-
000N0UJ430H 30G
MHDGWT-0000-
000N0UJ430G
K2 1200 1356 MHDGWT-0000-
000N0UK230H
MHDGWT-0000-
000N0UK230G
2700K
80
K2 1200 1356
27H
MHDGWT-0000-
000N0HK227H 27G
MHDGWT-0000-
000N0HK227G
K4 1290 1457 MHDGWT-0000-
000N0HK427H
MHDGWT-0000-
000N0HK427G
90
J2 1040 1175
27H
MHDGWT-0000-
000N0UJ227H 27G
MHDGWT-0000-
000N0UJ227G
J4 1120 1265 MHDGWT-0000-
000N0UJ427H
MHDGWT-0000-
000N0UJ427G
FLUX CHARACTERISTICS, EASYWHITE® ORDER CODES AND BINS - CONTINUED
Copyright © 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a
trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
5
XLamp® mHD-G LED
RELATIVE SPECTRAL POWER DISTRIBUTION
RELATIVE FLUX VS. JUNCTION TEMPERATURE
Testcondition:18V(forreference),If=700mA;36V,IF=350mA
Relative Spectral Power Distribution
0%
10%
20%
30%
40%
50%
60%
70%
80%
90%
100%
380 430 480 530 580 630 680 730 780
Relative Spectral Power
Wavelength (nm)
6500 K, 80 CRI
5000 K, 80 CRI
3000 K, 80 CRI
Relative Flux Output vs. Junction Temperature
0%
20%
40%
60%
80%
100%
120%
25 50 75 100 125 150
Relative Luminous Flux
Junction Temperature (ºC)
Copyright © 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a
trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
6
XLamp® mHD-G LED
ELECTRICAL CHARACTERISTICS (TJ
0
100
200
300
400
500
600
700
800
900
1000
16.0 16.5 17.0 17.5 18.0 18.5 19.0
Forward Current (mA)
Forward Voltage (V)
18 V
Electrical Characteristics (Tj = 85ºC)
0
50
100
150
200
250
300
350
400
450
500
32 33 34 35 36 37 38
Forward Current (mA)
Forward Voltage (V)
36 V
Copyright © 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a
trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
7
XLamp® mHD-G LED
RELATIVE FLUX VS. CURRENT (TJ
0%
20%
40%
60%
80%
100%
120%
140%
0 100 200 300 400 500 600 700 800 900 1000
Relative Luminous Flux
Forward Current (mA)
Relative Intensity vs. Current (Tj = 85ºC)
0%
20%
40%
60%
80%
100%
120%
140%
0 50 100 150 200 250 300 350 400 450 500
Relative Luminous Flux
Forward Current (mA)
36 V
Copyright © 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a
trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
8
XLamp® mHD-G LED
RELATIVE CHROMATICITY VS. CURRENT (WARM WHITE)
-0.015
-0.010
-0.005
0.000
0.005
0.010
0.015
100 200 300 400 500 600 700 800 900 1000
Current (mA)
ΔCCx
ΔCCy
18 V
-0.015
-0.010
-0.005
0.000
0.005
0.010
0.015
50 100 150 200 250 300 350 400 450 500
Current (mA)
ΔCCx
ΔCCy
36 V
Copyright © 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a
trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
9
XLamp® mHD-G LED
RELATIVE CHROMATICITY VS. TEMPERATURE (WARM WHITE)
Testcondition:18V(forreference),If=700mA;36V,IF=350mA
TYPICAL SPATIAL DISTRIBUTION
Testcondition:18V(forreference),If=700mA;36V,IF=350mA
-0.015
-0.010
-0.005
0.000
0.005
0.010
0.015
25 50 75 100 125 150
Tsp (°C)
ΔCCx
ΔCCy
Far Field
0%
20%
40%
60%
80%
100%
-90 -70 -50 -30 -10 10 30 50 70 90
Relative Luminous Intensity
Angle (º)
Copyright © 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a
trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
10
XLamp® mHD-G LED
THERMAL DESIGN
ThemaximumforwardcurrentisdeterminedbythethermalresistancebetweentheLEDjunctionandambient.Itiscrucialfortheend
product to be designed in a manner that minimizes the thermal resistance from the solder point to ambient in order to optimize lamp life
and optical characteristics.
0
100
200
300
400
500
600
700
800
900
1000
1100
0 20 40 60 80 100 120 140 160
Maximum Current (mA)
Ambient Temperature (ºC)
Rj-a = 4 °C/W
Rj-a = 5 °C/W
Rj-a = 6 °C/W
Rj-a = 7 °C/W
18 V
Thermal Design
0
50
100
150
200
250
300
350
400
450
500
550
0 20 40 60 80 100 120 140 160
Maximum Current (mA)
Ambient Temperature (ºC)
Rj-a = 4 °C/W
Rj-a = 5 °C/W
Rj-a = 6 °C/W
Rj-a = 7 °C/W
36 V
Copyright © 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a
trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
11
XLamp® mHD-G LED
PERFORMANCE GROUPS LUMINOUS FLUX (TJC)
XLampMHD‑GLEDsaretestedforluminousuxandplacedintooneofthefollowingbins.
Group Code Minimum Luminous Flux Maximum Luminous Flux
J2 1040 1120
J4 1120 1200
K2 1200 1290
K4 1290 1380
M2 1380 1485
M4 1485 1590
N2 1590 1710
N4 1710 1830
PERFORMANCE GROUPS CHROMATICITY
XLampMHD‑GLEDsaretestedforchromaticityandplacedintooneoftheregionsdenedbythefollowingboundingcoordinates.
EasyWhite Color Temperatures – 2-Step
Code CCT x y
40H 4000 K
0.3777 0.3739
0.3797 0.3816
0.3861 0.3855
0.3838 0.3777
35H 3500K
0.4022 0.3858
0.4053 0.3942
0.4125 0.3977
0.4091 0.3891
30H 3000 K
0.4287 0.3975
0.4328 0.4064
0.4390 0.4086
0.4347 0.3996
27H 2700K
0.4524 0.4048
0.4574 0.4140
0.4633 0.4154
0.4581 0.4062
Copyright © 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a
trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
12
XLamp® mHD-G LED
PERFORMANCE GROUPS - CHROMATICITY (TJ
EasyWhite Color Temperatures – 3-Step Ellipse
Bin Code CCT Center Point Major Axis Minor Axis Rotation Angle

x y a b
50G 5000K 0.3447 0.3553 0.00840 0.00312 65.0
40G 4000K 0.3818 0.3797 0.00939 0.00402 53.7
35G 3500K 0.4073 0.3917 0.00927 0.00414 53.2
30G 3000K 0.4338 0.4030 0.00834 0.00408 53.2
27G 2700K 0.4577 0.4099 0.00834 0.00420 48.5
EasyWhite Color Temperatures – 5-Step Ellipse
Bin Code CCT Center Point Major Axis Minor Axis Rotation Angle

x y a b
65E 6500K 0.3123 0.3282 0.01110 0.00550 61.0
57E 5700K 0.3287 0.3417 0.01230 0.00600 72.0
50E 5000K 0.3447 0.3553 0.01400 0.00520 65.0
40E 4000K 0.3818 0.3797 0.01565 0.00670 53.7
CREE’S STANDARD WHITE CHROMATICITY REGIONS PLOTTED ON THE 1931 CIE CURVE
2700 K
3000 K
3500 K
4000 K
4500 K
5000 K
5700 K
6500 K
8000 K
0.28
0.29
0.30
0.31
0.32
0.33
0.34
0.35
0.36
0.37
0.38
0.39
0.40
0.41
0.42
0.43
0.44
0.27
0.28
0.29
0.30
0.31
0.32
0.33
0.34
0.35
0.36
0.37
0.38
0.39
0.40
0.41
0.42
0.43
0.44
0.45
0.46
0.47
0.48
0.49
CCy
CCx
ANSI C78.377 Quadrangle
EasyWhite 5-Step
EasyWhite 3-Step
EasyWhite 2-Step
Copyright © 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a
trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
13
XLamp® mHD-G LED
BIN AND ORDER CODE FORMATS
BincodesandordercodesforMHD‑GLEDsareconguredinthefollowingmanner:
Order Code Bin Code
SSSSCC-HHHH-HHHGGNFFDDD
Series
MHDG = MHD-G
Internal code
CRI Specification
B = 70 CRI minimum
H = 80 CRI minimum
U = 90 CRI minimum
Chromaticity region
Flux
Vf class
N0 = 18-V/36-V class
Color
WT = White
SSSSCC-WWW-FF-GGN-AAAAA
Series
MHDG = MHD-G
Chromaticity bin
Vf class
N0 = 18-V/36-V class
Internal code
CRI Specification
B = 70 CRI minimum
H = 80 CRI minimum
U = 90 CRI minimum
Flux bin
Color
WT = White
Order and bin code headings
and diagrams are in a table
Copyright © 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a
trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
14
XLamp® mHD-G LED
REFLOW SOLDERING CHARACTERISTICS
Intesting,CreehasfoundXLampMHD‑GLEDstobecompatiblewithJEDECJ‑STD‑020C,usingtheparameterslistedbelow.Asageneral
guideline,Creerecommendsthatusersfollowtherecommendedsolderingproleprovidedbythemanufacturerofthesolderpasteused,
and therefore it is the lamp or luminaire manufacturer’s responsibility to determine applicable soldering requirements.
NotethatthisgeneralguidelinemaynotapplytoallPCBdesignsandcongurationsofreowsolderingequipment.
Profile Feature Lead-Free Solder
AverageRamp‑UpRate(Tsmax to Tp)1.2°C/second
Preheat: Temperature Min (Tsmin) 120°C
Preheat: Temperature Max (Tsmax)170°C
Preheat: Time (tsmin to tsmax)65‑150seconds
TimeMaintainedAbove:Temperature(TL)217°C
TimeMaintainedAbove:Time(tL)45‑90seconds
Peak/ClassicationTemperature(Tp) 235‑245°C
TimeWithin5°CofActualPeakTemperature(tp) 20‑40seconds
Ramp-Down Rate 1‑6°C/second
Time25°CtoPeakTemperature 4 minutes max.
Note:Alltemperaturesrefertothetopsideofthepackage,measuredonthepackagebodysurface.
TP
TL
Temperature
Time
t 25˚C to Peak
Preheat
ts
tS
tP
25
Ramp-down
Ramp-up
Critical Zone
TL to TP
Tsmax
Tsmin
Copyright © 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a
trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
15
XLamp® mHD-G LED
NOTES
Measurements
Theluminousux,radiantpower,chromaticity,forwardvoltageandCRImeasurementsinthisdocumentarebinningspecicationsonly
and solely represent product measurements as of the date of shipment. These measurements will change over time based on a number
offactorsthatarenotwithinCreescontrolandarenotintendedorprovidedasoperationalspecicationsfortheproducts.Calculated
valuesareprovidedforinformationalpurposesonlyandarenotintendedorprovidedasspecications.

Please read the LED Reliability OverviewfordetailsofthequalicationprocessCreeappliestoensurelong‑termreliabilityforXLamp
LEDsanddetailsofCreespre‑releasequalicationtestingforXLampLEDs.
Lumen Maintenance
CreenowusesstandardizedIESLM‑80‑08andTM‑21‑11methodsforcollectinglong‑termdataandextrapolatingLEDlumenmaintenance.
ForinformationonthespecicLM‑80datasetsavailableforthisLED,refertothepublicLM-80 results document.
Please read the Long-Term Lumen Maintenance application note for more details on Crees lumen maintenance testing and forecasting.
Please read the Thermal Management application note for details on how thermal design, ambient temperature, and drive current affect
the LED junction temperature.
Moisture Sensitivity
Cree recommends keeping XLamp LEDs in the provided, resealable moisture-barrier packaging (MBP) until immediately prior to soldering.
Unopened MBPs that contain XLamp LEDs do not need special storage for moisture sensitivity.
OncetheMBPisopened,XLampMHD‑GLEDsmaybestoredasMSL1perJEDECJ‑STD‑033,meaningtheyhaveunlimitedoorlifein
conditionsof≤30ºC/85%relativehumidity(RH).Regardlessofthestoragecondition,CreerecommendssealinganyunsolderedLEDs
in the original MBP.
RoHS Compliance
The levels of RoHS restricted materials in this product are below the maximum concentration values (also referred to as the threshold
limits)permittedforsuchsubstances,orareusedinanexemptedapplication,inaccordancewithEUDirective2011/65/EC(RoHS2),as
implementedJanuary2,2013.RoHSDeclarationsforthisproductcanbeobtainedfromyourCreerepresentativeorfromtheProduct
Ecology section of the Cree website.
REACh Compliance
REAChsubstancesofveryhighconcern(SVHCs)informationisavailableforthisproduct.SincetheEuropeanChemicalAgency(ECHA)
has published notice of their intent to frequently revise the SVHC listing for the foreseeable future, please contact a Cree representative
toinsureyougetthemostup‑to‑dateREAChDeclaration.REAChbannedsubstanceinformation(REAChArticle67)isalsoavailableupon
request.
Copyright © 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a
trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
16
XLamp® mHD-G LED
UL® Recognized Component
This product meets the requirements to be considered a UL Recognized Component with Level 4 enclosure consideration. The LED
packageoraportionthereofhasbeeninvestigatedasareandelectricalenclosureperANSI/UL8750.
Vision Advisory
WARNING:Donotlookatanexposedlampinoperation.Eyeinjurycanresult.FormoreinformationaboutLEDsandeyesafety,please
refer to the LED Eye Safety application note.
NOTES - CONTINUED
Copyright © 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a
trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
17
XLamp® mHD-G LED
MECHANICAL DIMENSIONS
Thermal vias, if present, are not shown on these drawings.
Allmeasurementsare±.13mmunlessotherwiseindicated.
Side View
7.00
7.00
6.70
REF.
.35
±0.2 mm
6.70
REF.
6.70
.70
.50
6.70
4.30
2.95
.80
6.760
.700
.700
3.900
.700
6.700
6.76
6.70
1.24
1.29
.25
.70
.70
.25
1.29
PRIMARY ALTERNATIVE
OPTICAL REFERENCE
Top View
0.75
±0.2 mm
.71
6.70
REF.
6.70
REF.
6.760
.700
.700
3.900
.700
6.700
6.76
6.70
1.24
1.29
.25
.70
.70
.25
1.29
ALTERNATIVE
OPTICAL REFERENCE
Anode
Side
Anode
Side
Cathode
Side
7.00
7.00
6.70
REF.
.35
±0.2 mm
6.70
REF.
6.70
.70
.50
6.70
4.30
2.95
.80
6.760
.700
.700
3.900
.700
6.700
6.76
6.70
1.24
1.29
.25
.70
.70
.25
1.29
PRIMARY ALTERNATIVE
OPTICAL REFERENCE
7.00
7.00
6.70
REF.
.35
±0.2 mm
6.70
REF.
6.70
.70
.50
6.70
4.30
2.95
.80
6.760
.700
.700
3.900
.700
6.700
6.76
6.70
1.24
1.29
.25
.70
.70
.25
1.29
PRIMARY ALTERNATIVE
OPTICAL REFERENCE
Bottom View Alternate Bottom View
Cathode
Side
Copyright © 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a
trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
18
XLamp® mHD-G LED
MECHANICAL DIMENSIONS - CONTINUED


Recommended Stencil Pattern
(Shaded Area Is Open)
SIZE
TITLE
OF
REV.
SHEET
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon Drive
Durham, N.C 27703
UNAUTHORIZED PERSON WITHOUT
THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTAINED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5 °
.XXX ± .25
.XX ± .75
.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125
X° ± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH:
1.6
7.00
7.00
0.75
±0.2 mm
.71
6.70
REF.
.35
±0.2 mm
6.70
REF.
6.70
.70
.50
6.70
4.30
2.95
.80
6.76
.70
.70
3.90
.70
6.70
6.76
6.70
1.24
1.29
.25
.70
.70
.25
1.29
1/115.000
B
2610-00051-OUTLINE
7x7 MHD-E 9V/36V
7x7 MHD-G 18V
11/12/14D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
RECOMMENDED PCB SOLDER PAD
RECOMMENDED STENCIL PATTERN
(HATCHED AREA IS OPEN)
PRIMARY ALTERNATIVE
ALL DIMENSIONS ARE ± .13mm UNLESS OTHERWISE NOTED
Recommended PCB Solder Pad
SIZE
TITLE
OF
REV.
SHEET
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon Drive
Durham, N.C 27703
UNAUTHORIZED PERSON WITHOUT
THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTAINED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5 °
.XXX ± .25
.XX ± .75
.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125
X° ± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH:
1.6
7.00
7.00
0.75
±0.2 mm
.71
6.70
REF.
.35
±0.2 mm
6.70
REF.
6.70
.70
.50
6.70
4.30
2.95
.80
6.76
.70
.70
3.90
.70
6.70
6.76
6.70
1.24
1.29
.25
.70
.70
.25
1.29
1/115.000
B
2610-00051-OUTLINE
7x7 MHD-E 9V/36V
7x7 MHD-G 18V
11/12/14D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
RECOMMENDED PCB SOLDER PAD
RECOMMENDED STENCIL PATTERN
(HATCHED AREA IS OPEN)
PRIMARY ALTERNATIVE
ALL DIMENSIONS ARE ± .13mm UNLESS OTHERWISE NOTED
SIZE
TITLE
OF
REV.
SHEET
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon Drive
Durham, N.C 27703
UNAUTHORIZED PERSON WITHOUT
THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTAINED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5 °
.XXX ± .25
.XX ± .75
.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125
X° ± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH:
1.6
7.00
7.00
0.75
±0.2mm
.71
6.70
REF.
6.70
REF.
.35
±0.2mm
3.13
.50
6.76
6.70
.70
1.29
1.24
.25
.70
.25
1.29
6.76 .50
3.13
.70
.70
.70
.70
6.70
.80
2.95
6.70
6.70
4.30
.50 .70
1/115.000
A
2610-00052-OUTLINE
7x7 MHD-E 18V
7x7 MHD-G 36V
11/17/14D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
RECOMMENDED PCB SOLDER PAD
RECOMMENDED STENCIL PATTERN
(HATCHED AREA IS OPENING)
ALL DIMENSIONS ARE .13mm UNLESS OTHERWISE NOTED
PRIMARY ALTERNATIVE
Recommended PCB Solder Pad Recommended Stencil Pattern
(Shaded Area Is Open)
SIZE
TITLE
OF
REV.
SHEET
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon Drive
Durham, N.C 27703
UNAUTHORIZED PERSON WITHOUT
THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTAINED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5 °
.XXX ± .25
.XX ± .75
.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125
X° ± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH:
1.6
7.00
7.00
0.75
±0.2mm
.71
6.70
REF.
6.70
REF.
.35
±0.2mm
3.13
.50
6.76
6.70
.70
1.29
1.24
.25
.70
.25
1.29
6.76 .50
3.13
.70
.70
.70
.70
6.70
.80
2.95
6.70
6.70
4.30
.50 .70
1/115.000
A
2610-00052-OUTLINE
7x7 MHD-E 18V
7x7 MHD-G 36V
11/17/14D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
RECOMMENDED PCB SOLDER PAD
RECOMMENDED STENCIL PATTERN
(HATCHED AREA IS OPENING)
ALL DIMENSIONS ARE .13mm UNLESS OTHERWISE NOTED
PRIMARY ALTERNATIVE
Copyright © 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a
trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
19
XLamp® mHD-G LED
ELECTRICAL CONFIGURATION
18 V
NEGATIVE (-)
POSITIVE (+)
36 V
NEGATIVE (-)
POSITIVE (+)
SOLDER PAD LINK
POSITIVE (+)
NEGATIVE (-)
18 V
NEGATIVE (-)
POSITIVE (+)
36 V
NEGATIVE (-)
POSITIVE (+)
SOLDER PAD LINK
POSITIVE (+)
NEGATIVE (-)
 
Copyright © 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a
trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
20
XLamp® mHD-G LED
TAPE AND REEL
AllCreecarriertapesconformtoEIA‑481D,AutomatedComponentHandlingSystemsStandard.
Allmeasurementsare±.13mmunlessotherwiseindicated.
SIZE
TITLE
OF
REV.
SHEET
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
± .5 °
.XXX ± .010
.XX ± .03
.X ± .06
FOR SHEET METAL PARTS ONLY
.XX ± .01
.XXX ± .005
± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES
AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon Drive
Durham, N.C 27703
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTANED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
SURFACE FINISH:
63
330
+.25
-.75
12.4
+1.0
-.5
MEASURED AT EDGE
16.4
+0.2
.0
MEASURED AT HUB
12.4
+.2
.0
MEASURED AT HUB
±.213.1
1.9±.4
±.421
60° 60°
1/10.500
A
2400-00009
REEL, 13" X 12MM, 3 PIECE SNAP
-
ANTI-STATIC HIPS
----
----
09/29/09D. CRONIN
2400-00009
INDEX QTY ITEM COMMENTS
1 1 2400-00009-CORE
2 2 2400-00009-REEL
REVISONS
REV DESCRIPTION BY DATE APP'D
.30
[.012]
T
7.60 [.299]
1.70 [.067]
Ko
3.0°
7.60
[.299]
Bo
2.00 [.079]
P2
4.00 [.157]
Po
14.25
[.561]
E2
Do
1.50+.10
-.00 .0591+.0039
-.0000[ ]
3.0°
16.00 [.630]
NOMINAL
16.30 [.642]
MAX
W
1.75 [.069]
E1
7.50 [.295]F
1.50 [.059]
D1
MIN
12.00 [.472]
P
CATHODE SIDE
ANODE SIDE
1000 LEDs per reel
Copyright © 2015-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a
trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
21
XLamp® mHD-G LED
PACKAGING
Label with Cree Bin
Code, Qty, Lot # Label with Cree Bin
Code, Qty, Lot #
Vacuum-Sealed
Moisture Barrier Bag
Dessicant
(inside bag)
Humidity Indicator
Card (inside bag)
Patent Label
Label with Customer Order
Code, Qty, Reel ID, PO #
Patent Label
Label with Cree Bin Code,
Quantity, Reel ID
Label with Cree Bin Code,
Quantity, Reel ID
Label with Cree Order Code,
Quantity, Reel ID, PO #
Label with Cree Order Code,
Quantity, Reel ID, PO #
Label with Cree Bin Code,
Quantity, Reel ID
Unpackaged Reel
Packaged Reel
Boxed Reel
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Cree, Inc.:
MHDGWT-0000-000N0HK235G MHDGWT-0000-000N0HM230G MHDGWT-0000-000N0HK430G MHDGWT-0000-
000N0HK440G MHDGWT-0000-000N0HK227G MHDGWT-0000-000N0HK230G MHDGWT-0000-000N0HK435G
MHDGWT-0000-000N0HM235G MHDGWT-0000-000N0HK427G MHDGWT-0000-000N0HM227G MHDGWT-0000-
000N0HM450E MHDGWT-0000-000N0HM250E MHDGWT-0000-000N0HM240G MHDGWT-0000-000N0HK435H
MHDGWT-0000-000N0HK430H MHDGWT-0000-000N0UJ430H MHDGWT-0000-000N0UJ227G MHDGWT-0000-
000N0BM457E MHDGWT-0000-000N0UJ227H MHDGWT-0000-000N0UK230H MHDGWT-0000-000N0BM440E
MHDGWT-0000-000N0HK427H MHDGWT-0000-000N0HM235H MHDGWT-0000-000N0UK240H MHDGWT-0000-
000N0HM230H MHDGWT-0000-000N0HM265E MHDGWT-0000-000N0HM457E MHDGWT-0000-000N0UK450E
MHDGWT-0000-000N0UK240G MHDGWT-0000-000N0UK450G MHDGWT-0000-000N0UJ435H MHDGWT-0000-
000N0UJ435G MHDGWT-0000-000N0BM240E MHDGWT-0000-000N0UK250G MHDGWT-0000-000N0UK235H
MHDGWT-0000-000N0BM450E MHDGWT-0000-000N0BM465E MHDGWT-0000-000N0BM250E MHDGWT-0000-
000N0UK235G MHDGWT-0000-000N0HM257E MHDGWT-0000-000N0HM465E MHDGWT-0000-000N0UK230G
MHDGWT-0000-000N0UJ427H MHDGWT-0000-000N0HM250G MHDGWT-0000-000N0BN257E MHDGWT-0000-
000N0BM257E MHDGWT-0000-000N0BM265E MHDGWT-0000-000N0HM227H MHDGWT-0000-000N0UJ427G
MHDGWT-0000-000N0HM240H MHDGWT-0000-000N0UK440H MHDGWT-0000-000N0HK440H MHDGWT-0000-
000N0UK440G MHDGWT-0000-000N0UK250E MHDGWT-0000-000N0HM450G MHDGWT-0000-000N0BN265E
MHDGWT-0000-000N0UK227G MHDGWT-0000-000N0UJ430G MHDGWT-0000-000N0HK230H MHDGWT-0000-
000N0HK235H MHDGWT-0000-000N0BN250E MHDGWT-0000-000N0HK227H MHDGWT-0000-000N0UK227H