EMCComponents Feed-Through Capacitors Feed-Through Filters in Solderless MKP Technology Data Book Supplement Vakatseite (( 2 )) Feed- Through Capacitors Feed- Through Filters 1 B85121 B85321 General MeshContact is a solderless technology newly developed by Siemens Matsushita Components. It allows uniform concentric contacting of MKP capacitor winds, avoiding the thermal stress caused by soldering. The result is even better insertion loss, high insulation resistance plus compact, small casing. Basically, feed- through components can be used to suppress interference in all electrical installations and equipment. The new series is also ideal for telephone switching systems and base stations and, through broadband suppression effective into the GHz region, prevents interference pulses from entering equipment from outside through the power supply network and vice versa. There is now a building- block system available in this new technology for feed- through capacitors and filters, allowing fast and attractively priced solutions to be implemented. Interim ratings can be produced to order for special applications. Feed- through elements fitted into a shielding wall Selector guide Diameter Voltage range Capacitance range 30 mm up to 75 A 0,1 ... 1 F 55 mm up to 500 A 0,5 ... 4,7 F Siemens Matsushita Components 9.98 3 Feed- Through Capacitors Feed- Through Filters B85121 B85321 In feed- through capacitors the conductor carrying the load current is connected concentrically to one electrode and passes through the center of the capacitor. The other electrode makes concentric contact with the capacitor case. Feed- through capacitors are designed to be effective from low frequency to far above 300 MHz. The low- loss winding with high- stability contact to the leads at its face ends is enclosed in a metal case with either a threaded stud at one end or an external thread. Feed- through filters have filter circuits consisting of two equal shunt capacitors and one ferromagnetic inductor connected in series. Due to the concentric arrangement of the components, high attenuation values are obtained for frequencies up to and exceeding 1 GHz. Safety note! If feed- through elements with high capacitances are used, protective measures (e.g. protective earthing) in accordance with equipment/system regulations (product standards) are required! 2 Mounting instructions To fully utilize their RF characteristics, feed- through components must be fitted directly into the shielding wall. The component case must make perfect and unbroken (RF- tight!) contact with the shielding. This can be best achieved by screwing them into a threaded hole or bushing, so that good electrical contact is made by the flanks of the thread. As an alternative, feed- through elements can be screwed into feed- through holes in a shielding wall and held by a retaining nut. Contact between the case and the shielding wall is produced by the contact surface on the thread. The connecting line must be attached by fixing it between two countered nuts in order to avoid exposing the component to torque loads (use two spanners). NOTE Due to the danger of exposing the feed throughs to mechanical loads caused by shock and vibration, it is not permissible to use rigid copper bars as connecting elements. 4 9.98 Siemens Matsushita Components Feed- Through Capacitors Feed- Through Filters B85121 B85321 Construction Building- block system MKP technology (dry, self- healing) Dielectric: polypropylene, metallized Metal case with synthetic resin terminals For central screw fixing Features Compact dimensions Variable current rating and capacitance through building- block system High attenuation Simple fitting High contact reliability through central screw fixing Applications Broadband interference suppression for ac/dc supply lines, e.g. in shielded rooms telephone exchanges, base stations electrical machines and systems power supplies Terminals Threaded studs Marking Manufacturer, ordering code, EMI suppression class, rated capacitance, rated voltage, rated current, climatic category, circuit diagram, date of manufacture (MM.YY) Standards Feed- through capacitors comply with EN 133 200 Feed- through filters comply with EN 133 400 Safety information Due to the high capacitance ratings protective measures (e.g. protective earthing) in accordance with equipment/system regulations are required. Circuit diagrams SSB1274-B Feed- through filters Siemens Matsushita Components SSB1275-J Feed- through capacitors 9.98 5 Feed- Through Capacitors B85121 Feed- through capacitors 30 mm IR CR VR VP Terminal Dimensions (mm) A F Vac Vdc Vdc 25 0,1 250 600 3000 M6 30 x 55 110 B85121- A2104- A250 0,5 250 600 2500 M6 30 x 55 110 B85121- A2504- A250 1,0 250 600 2000 M6 30 x 55 110 B85121- A2105- A250 0,1 250 600 3000 M6 30 x 55 110 B85121- A2104- A750 0,5 250 600 2500 M6 30 x 55 110 B85121- A2504- A750 1,0 250 600 2000 M6 30 x 55 110 B85121- A2105- A750 75 xl Ordering code l 1 Insertion loss (dB); typical values at 50 Capacitance C R 10 kHz 1 MHz 10 MHz 100 MHz 1 GHz 0,1 F 0 5 20 40 60 70 0,5 F 2 15 35 40 80 > 90 1,0 F 5 25 45 50 85 > 90 100 kHz General technical data Capacitance tolerance: IEC climatic category: Screw cap fixing: 20 % 40/085/56 (- 40 C/ + 85 C, 56 days damp heat test) standard M20 x 1 Dimensional drawing M6 o30 M6 M20x1 Marking l 5 l1 SSB1271-L 6 9.98 Siemens Matsushita Components Feed- Through Capacitors B85121 Feed- through capacitors 55 mm IR A 63 100 200 CR VR VP Terminal Dimensions (mm) Ordering code F Vac Vdc Vdc M xl l 0,5 250 600 3000 M6 55 x 30 100 B85121- A2504- A630 1,0 250 600 2500 M6 55 x 30 100 B85121- A2105- A630 2,0 250 600 2500 M6 55 x 60 130 B85121- A2205- A630 4,7 250 600 2000 M6 55 x 60 130 B85121- A2475- A630 0,5 250 600 3000 M8 55 x 30 110 B85121- A2504- A101 1,0 250 600 2500 M8 55 x 30 110 B85121- A2105- A101 2,0 250 600 2500 M8 55 x 60 140 B85121- A2205- A101 4,7 250 600 2000 M8 55 x 60 140 B85121- A2475- A101 0,5 250 600 3000 M10 55 x 30 120 B85121- A2504- A201 1,0 250 600 2500 M10 55 x 30 120 B85121- A2105- A201 2,0 250 600 2500 M10 55 x 60 150 B85121- A2205- A201 4,7 250 600 2000 M10 55 x 60 150 B85121- A2475- A201 1 Insertion loss (dB); typical values at 50 Capacitance C R 100 kHz 1 MHz 10 MHz 100 MHz 1 GHz 0,5 F 10 kHz 2 15 35 40 80 > 90 1,0 F 5 25 45 50 85 > 90 2,0 F 10 30 50 55 > 90 > 90 4,7 F 15 35 55 65 > 90 > 90 Siemens Matsushita Components 9.98 7 Feed- Through Capacitors B85121 General technical data Capacitance tolerance: IEC climatic category: Screw cap fixing 20 % 40/085/56 (- 40 C/ + 85 C, 56 days damp heat test) standard M32 x 1,5; special fixing M27 x 1,5 possible. Dimensional drawing SW41 Marking SW17 M32x1,5 M 24 min. 8 551 15+1 l 56 l1 SSB1272-U 8 9.98 Siemens Matsushita Components Feed- Through Filters B85321 Feed- through filters 30 mm IR CR A 25 75 VR VP Terminal Dimensions (mm) Ordering code F Vac Vdc Vdc xl l 2 x 0,1 250 600 3000 M6 30 x 81 130 B85321- A2204- A250 2 x 0,5 250 600 2000 M6 30 x 81 130 B85321- A2105- A250 2 x 1,0 250 500 1700 M6 30 x 81 130 B85321- A2205- A250 2 x 0,1 250 600 3000 M6 30 x 81 130 B85321- A2204- A750 2 x 0,5 250 600 2000 M6 30 x 81 130 B85321- A2105- A750 2 x 1,0 250 500 1700 M6 30 x 81 130 B85321- A2205- A750 1 Insertion loss (dB); typical values at 50 , load- independed Capacitance C R 10 kHz 100 kHz 1 MHz 10 MHz 100 MHz 1 GHz 2 10 25 70 > 100 > 100 2 x 0,5 F 5 25 45 80 > 100 > 100 2 x 1,0 F 10 30 60 90 > 100 > 100 2 x 0,1 F General technical data Capacitance tolerance: IEC climatic category: screw cap fixing: 20 % 40/085/56 (- 40 C/ + 85 C, 56 days damp heat test) standard M20 x 1 Dimensional drawing M6 o30 M6 M20x1 Marking l 5 l1 SSB1271-L Siemens Matsushita Components 9.98 9 Feed- Through Filters B85321 Feed- through filters 55 mm IR CR VR F VP Terminal Dimensions (mm) Ordering code Vac Vdc Vdc M xl l 63 A 2 x 0,5 F 250 600 3000 M6 55 x 100 166 B85321- A2105- A630 2 x 1,0 F 250 600 2500 M6 55 x 100 166 B85321- A2205- A630 2 x 2,0 F 250 600 2500 M6 55 x 100 166 B85321- A2405- A630 2 x 4,7 F 250 600 1650 M6 55 x 100 166 B85321- A2945- A630 100 A 2 x 0,5 F 250 600 3000 M8 55 x 100 180 B85321- A2105- A101 2 x 1,0 F 250 600 2500 M8 55 x 100 180 B85321- A2205- A101 2 x 2,0 F 250 600 2500 M8 55 x 100 180 B85321- A2405- A101 2 x 4,7 F 250 600 1650 M8 55 x 100 180 B85321- A2945- A101 200 A 2 x 0,5 F 250 600 3000 M10 55 x 100 185 B85321- A2105- A201 2 x 1,0 F 250 600 2500 M10 55 x 100 185 B85321- A2205- A201 2 x 2,0 F 250 600 2500 M10 55 x 100 185 B85321- A2405- A201 2 x 4,7 F 250 600 1650 M10 55 x 100 185 B85321- A2945- A201 300 A 2 x 0,5 F 250 600 3000 M12 55 x 100 195 B85321- A2105- A301 2 x 1,0 F 250 600 2500 M12 55 x 100 195 B85321- A2205- A301 2 x 2,0 F 250 600 2500 M12 55 x 100 195 B85321- A2405- A301 2 x 4,7 F 250 600 1650 M12 55 x 100 195 B85321- A2945- A301 400 A 2 x 0,5 F 250 600 3000 M16 55 x 130 245 B85321- A2105- A401 2 x 1,0 F 250 600 2500 M16 55 x 130 245 B85321- A2205- A401 2 x 2,0 F 250 600 2500 M16 55 x 130 245 B85321- A2405- A401 2 x 4,7 F 250 600 1650 M16 55 x 130 245 B85321- A2945- A401 500 A 2 x 0,5 F 250 600 3000 M18 55 x 130 250 B85321- A2105- A501 2 x 1,0 F 250 600 2500 M18 55 x 130 250 B85321- A2205- A501 2 x 2,0 F 250 600 2500 M18 55 x 130 250 B85321- A2405- A501 2 x 4,7 F 250 600 1650 M18 55 x 130 250 B85321- A2945- A501 A 1 Insertion loss (dB); typical values at 50 , load- independed Capacitance C R 100 kHz 1 MHz 10 MHz 100 MHz 1 GHz 2 x 0,5 F 5 25 45 80 > 100 > 100 2 x 1,0 F 10 30 60 > 100 > 100 > 100 2 x 2,0 F 15 35 70 > 100 > 100 > 100 2 x 4,7 F 25 40 90 > 100 > 100 > 100 10 10 kHz 9.98 Siemens Matsushita Components Feed- Through Filters B85321 General technical data Capacitance tolerance: IEC climatic category: Screw cap fixing: 20 % 40/085/56 (- 40 C/ + 85 C, 56 days damp heat test) standard M32 x 1,5 special fixing M27 x 1,5 possible for filters up to 300 A. Dimensional drawing 15 min. M SW10 Marking 551 15 min. M32x1,5 SW41 8 15+1 45 _ 3 l l1 SSB1273-3 Siemens Matsushita Components 9.98 11 Published by Siemens Matsushita Components GmbH & Co. KG Marketing Kommunikation, Postfach 80 17 09, D- 81617 Munchen Siemens Matsushita Components 1998. All Rights Reserved. As far as patents or other rights of third parties are concerned, liability is only assumed for components per se, not for applications, processes and circuits implemented within components or assemblies. The information describes the type of component and shall not be considered as assured characteristics. Terms of delivery and rights to change design reserved. This brochure replaces the previous edition. For questions on technology, prices and delivery please contact the Sales Offices of Siemens AG, Passive Components and Electron Tubes Group, in the Federal Republic of Germany or the international Siemens Companies and Representatives. Due to technical requirements components may contain dangerous substances. For information on the type in question please also contact one of our Sales Offices. 12 9.98 Siemens Matsushita Components