DMF5002NY-EB-AAE (AO) No.99-0199 OPTREX CORPORATION Page 1/17
OPTREX
Type No.
*******
Jul 14, 1999
First Edition
Final Revisi on
Quality A ssurance Di v.
Product i on Di v.
Checked by
Checked by
Approved by
Product i on Di v.
Design Engi neeri ng Di v.
Prepared by
LCD Module Specification
ＤＭＦ５００２ＮＹ－ＥＢ－ＡＡＥ
ＤＭＦ５００２ＮＹ－ＥＢ－ＡＡＥＤＭＦ５００２ＮＹ－ＥＢ－ＡＡＥ
ＤＭＦ５００２ＮＹ－ＥＢ－ＡＡＥ
Table of Cont ent s
1. General Specifications .............................................................................2
2. Electrical Specifications...........................................................................3
3. Optical Specifications..............................................................................7
4. I/O Terminal.............................................................................................9
5. Test..........................................................................................................11
6. Appearance Standards............................................................................12
7. Code System of Production Lot ..........................................................15
8. Type Number..........................................................................................15
9. Applying Precautions.............................................................................15
10. Precautions Relating Product Handling................................................16
11. Warranty..................................................................................................17
Revision History
Rev. Date Page Comment
DMF5002NY-EB-AAE (AO) No.99-0199 OPTREX CORPORATION Page 2/17
OPTREX
1. General Specifications
Operating Temp . ： min. 0℃ ～ max. 50℃
Storage Temp. ： min. -20℃ ～ max. 60℃
Dot Pixels ： 128 (W) × 112 (H) dots
Dot Size ： 0.50 (W) × 0.49 (H) mm
Dot Pitch ： 0.54 (W) × 0.53 (H) mm
Viewing Area ： 77.0 (W) × 66.0 (H) mm
Outline Dimensions ： 110.0 (W) × 90.6 (H) × 12.8 (D) mm
Weight ： 120g max.
LCD Type ： NSD-7399
( STN / Yellow-mode / Transflective )
Viewing Angle ： 6:00
Control LSI ： T6963C-0101 (Produced by TOSHIBA)
Data Transfer ： 8-bit parallel data transfer
Backlight ： Electro Luminescence (EL) / Blue-green
Drawings ： Dimensional Outline UE-301031
DMF5002NY-EB-AAE (AO) No.99-0199 OPTREX CORPORATION Page 3/17
OPTREX
2.Electrical Specifications
2.1.Absolute Maximum Ratings VSS=0V
Parameter Symbol Conditions Min. Max. Units
Supply Voltage
(Logic)
VCC-VSS － -0.3 7.0 V
Supply Voltage
(LCD Drive)
VCC-VEE － -0.3 30.0 V
Input Voltage VI － -0.3 VCC+0.3 V
2.2.DC Characteristics Ta=25℃, VSS=0V
Parameter Symbol Conditions Min. Typ. Max. Units
Supply Voltage
(Logic)
VCC-VSS － 4.5
－ 5.5 V
VCC-VEE － 21.0
－ 26.0 V
Supply Voltage
(LCD Drive) VCC-VADJ Shown in 3.1 V
High Level
Input Voltage
VIH V
CC=5.0V±10% VCC-2.2 － V
CC V
Low Level
Input Voltage
VIL V
CC=5.0V±10% 0 － 0.8 V
High Level
Output Voltage
VOH I
OH=-0.75mA VCC-0.3 － V
CC V
Low Level
Output Voltage
VOL I
OL=0.75mA 0
－ 0.3 V
Supply Current
ICC V
CC-VSS=5.0V － 9.0 20.0 mA
I
EE V
CC-VADJ=18.3V － 4.0 10.0 mA
DMF5002NY-EB-AAE (AO) No.99-0199 OPTREX CORPORATION Page 4/17
OPTREX
2.3.AC Characteristics VCC=5.0V±10%
Parameter Symbol Min. Max. Units
C/D Setup Time tCDS 100
－ ns
C/D Hold Time tCDH 10
－ ns
CE, RD, WR Pulse Width tCE, tRD, tWR 80 － ns
Data Setup Time tDS 80
－ ns
Data Hold Time tDH 40
－ ns
Access Time tACC － 150 ns
Output Hold Time tOH 10 50 ns
(WRITE)
(READ)
RD, WR
D0～D7
CE
C/D
D0～D7
tDS
tOH
tDH
tACC
tCE, tRD, tWR
tCDH
tCDS
DMF5002NY-EB-AAE (AO) No.99-0199 OPTREX CORPORATION Page 5/17
OPTREX
2.4.Power Supply ON/OFF Sequence
2.4.1.ON Sequence
2.4.2.OFF Sequence
2.4.3.Reset Sequence
Please maintain the above sequence when turning on and off the power supply of the module.
If VEE and/or VADJ is supplied to the module while internal alternate signal for LCD driving
(M) is unstable or RESET is active, DC component will be supplied to the LCD panel. This
may cause damage to the LCD mod ule.
RESET
VCC
VADJ
SIGNAL
T≧0
T≧0T≧0T≧50msT≧50ms
T>250μs
LEVEL
L Level
H Level
VCC
VADJ
VCC
VSS
Power OffPower On Reset CancellationReset
T≧10 ms
VEE
VSS
VSS
VCC
VSS
VCC
VCC
VEE
0≦t
SIGNAL
0≦t
SIGNAL
VCC
LEVEL
VADJ
VADJ
(Without RESET Si gnal)
VEE
VSS
VSS
VCC
VSS
VCC
VCC
VEE
0≦t
SIGNAL
0≦t
SIGNAL
VCC
LEVEL
VADJ
VADJ
(W ithout RESET Signal)
DMF5002NY-EB-AAE (AO) No.99-0199 OPTREX CORPORATION Page 6/17
OPTREX
2.5.Lighting Specifications
2.5.1.Absolute Maximum Rating Ta=25℃
Parameter Conditions Min. Typ. Max. Units
Input Voltage － － － 150 Vrms
Input Frequency AC100Vrms － － 800 Hz
2.5.2.Operating Characteristics Ta=25℃
Parameter Conditions Min. Typ. Max. Units
Input Voltage － － 100 － Vrms
Input Frequenc y － － 400 － Hz
Current AC100Vrms, 400Hz
－ 9.4 12.0 mA
Luminance of
Backlight Surface
AC100Vrms, 400Hz 40 50 － cd/㎡
Life AC100Vrms, 400Hz
Ta=20℃, 60%RH
2000 － － hrs
Recommended Inverter : NS-106 ( Produced by NEC )
DMF5002NY-EB-AAE (AO) No.99-0199 OPTREX CORPORATION Page 7/17
OPTREX
3.Optical Specifications
3.1.LCD Driving Voltage
Parameter Symbol Conditions Min. Typ. Max. Units
Recommended Ta= 0℃ － － 21.9 V
LCD Driving Voltage VCC-VADJ Ta=25℃ 17.0 18.3 19.6 V
Note 1 Ta=50℃ 15.3
－ － V
Note 1 : Voltage (Applied actual waveform to LCD Module) for the best contrast. The range of
minimum and maximum shows tolerance of the operating voltage. The specified contrast ratio and
response time are not guaranteed over the entire range.
3.2.Optical Characteristics Ta=25℃, 1/128 Duty, 1/11.6 Bias, VD=18.3V (Note 4), θ= 0 ﾟ, φ=－ﾟ
Parameter Symbol Conditions Min. Typ. Max. Units
Contrast Ratio No te 1 CR θ= 0 ﾟ, φ=－ﾟ － 8 －
Viewing Angle Shown in 3.3
Response Rise
Note 2 TON － － 200 300 ms
Time Decay Note 3 TOFF － － 340 510 ms
Note 1 : Contrast ratio is d e finded as follows.
CR = LOFF / LON
LON : Luminance of the ON segments
LOFF : Luminance of the OFF segments
Note 2 : The time that the luminance level reaches 90% of the saturation level from 0% when ON
signal is applied.
Note 3 : The time that the luminance level reaches 10% of the saturation level from 100% when OFF
signal is applied.
Note 4 : Definition of Driving Voltage VD
VD=VCC-VADJ-VBE
Assuming that the typical driving waveforms shown below are applied to the LCD Panel at
1/A Duty - 1/B Bias ( A : Duty Number, B : Bias Number ). Driving voltage VD is definded
as follows.
VD = (Vth1+Vth2) / 2
Vth1 : The voltage VO-P that should pro vide 50% of the saturation level in the luminance at
the segment which the ON signal is applied to.
Vth2 : The voltage VO-P that should pro vide 50% of the saturation level in the luminance at
the segment which the OFF signal is applied to.
VO-P
1 / fF
(
B-2
)
×VO-P / B
1 /
(
fF×A
)
〈OFF SIGNAL〉
〈ON SIGNAL〉
DMF5002NY-EB-AAE (AO) No.99-0199 OPTREX CORPORATION Page 8/17
OPTREX
3.3.Definition of Viewing Angle and Optimum Viewing Area
･Point ● shows the point where contrast ratio is measured. : θ= 0 ﾟ, φ=－ﾟ
･Driving condition : 1/128 Duty, 1/11.6 Bias, VD=18.3V, fF=70Hz
･Area shows typ. CR
≧2
3.4.System Block Diagram
270 ﾟ
0ﾟ
90 ﾟ
180 ﾟ
270 ﾟ
θ
φ
135 ﾟ
315 ﾟ
225 ﾟ
45 ﾟ
180 ﾟ
90 ﾟ
(φ= 0 ﾟ）
φ
10 20 30 40 50
θ
φ
Halogen bulb
Computer
Rotation Table (θ,φ)
Temperature Chamber
LCD
Optical Fiber
Waveform Generator
Control Unit &
#1980A WB
Photometer
θ
DMF5002NY-EB-AAE (AO) No.99-0199 OPTREX CORPORATION Page 9/17
OPTREX
4.I/O Terminal
4.1.Pin Assignment
No. Symbol Level Function
1 FG － Frame Ground
2 V
SS ― Power Supply (0V, GND)
3 V
CC ― Power Supply for Logic
4 V
ADJ ― Voltage Level for LCD Contrast Ad justment
5 V
EE ― Power Supply for LCD Drive
6 WR H / L Write Signal L : Active
7 RD H / L Read Signal L : Active
8 CE H / L Chip Enable Signal L : Active
9 C/D H / L Write Mode H : Command Write L : Data Write
Read Mode H : Status Read L : Data Read
10 HALT H / L Clock Operating Stop Signal L : Halt
11 RESET H / L Reset Signal L : Reset
12 D0 H / L Display Data
13 D1 H / L Display Data
14 D2 H / L Display Data
15 D3 H / L Display Data
16 D4 H / L Display Data
17 D5 H / L Display Data
18 D6 H / L Display Data
19 D7 H / L Display Data
20 NC － Non-connection
21 EL － Power Supply for EL
22 EL － Power Supply for EL
4.2.Example of Power Supply
It is recommended to apply a potentiometer for the contrast adjust due to the tolerance
of the driving voltage and its temperature dependence.
MODULE
VADJ
VCC
VEE
VSS VSS (0V)
VCC (+Volt ag e )
R1+R2+VR=10～20KΩ
VEE (-Voltage)
R2
R1
VR
DMF5002NY-EB-AAE (AO) No.99-0199 OPTREX CORPORATION Page 10/17
OPTREX
4.3.Block Diagram
EL
EL
VADJ
FG
VSS
VCC
RESET
D0～D7
CE
RD
WR
C/D
HALT
or equivalent
T6A40 × 2
T6963C
Control LSI
Row Driver
or equivalent
T6A39 × 2
Column Driver
L C D P
2128
128 × 112 dots
To LSIBias Circuit
EL Back light
8
3
5
112
813
64K S-RAM
X-tal
J
M Circuit
1
VEE
DMF5002NY-EB-AAE (AO) No.99-0199 OPTREX CORPORATION Page 11/17
OPTREX
5.Test
No change on display and in operation under the following test condition.
No. Parameter Conditions Notes
1 High Temperature Operating 50℃±2℃, 96hrs (operation state)
2 Low Temperature Operating 0℃±2℃, 96hrs (operation state) 3
3 High Temperature Storage 60℃±2℃, 96hrs 4
4 Low Temperature Storage -20℃±2℃, 96hrs 3, 4
5 Damp Proof Test 40℃±2℃, 90～95%RH, 96hrs 3, 4
6 Vibration Test Total fixed amplitude : 1.5mm 5
Vibration Frequency : 10～55Hz
One cycle 60 seconds to 3 directions of X, Y, Z for
each 15 minutes
7 Shock Test To be measured after dropping from 60cm high on
the concrete surface in packing state.
Note 1 : Unless otherwise specified, tests will be conducted under the following condition.
Temperature : 20±5℃
Humidity : 65±5%
Note 2 : Unless otherwise specified, tests will be not conducted under functioning state.
Note 3 : No dew condensation to be observed.
Note 4 : The function test shall be conducted after 4 hours storage at the normal temp erature and humidity
after removed from the test chamber.
Note 5 : Vibration test will be conducted to the prod uct itself without putting it in a container.
E
A
GDC
F
60cm
C o ncrete S urface
Dropping method corner dropping
E,F,G face : once
B,C,D edge : once
A corner : once
Face dropping
Edge drop ping
B
DMF5002NY-EB-AAE (AO) No.99-0199 OPTREX CORPORATION Page 12/17
OPTREX
6.Appearance Standards
6.1.Inspection conditions
The LCD shall be inspected under 40W white fluorescent light.
The distance between the eyes and the sample shall be more than 30cm.
All directions for inspecting the sample should be within 45 ﾟagainst perpendicular line.
6.2.Definition of applicable Zones
A Zone : Active display area
B Zone : Area from outside of "A Zone" to validity viewing area
C Zone : Rest parts
A Zone + B Zone = Vali dity viewing area
A Zone
B Zone
C Zone
Bezel Flame
45ﾟ
DMF5002NY-EB-AAE (AO) No.99-0199 OPTREX CORPORATION Page 13/17
OPTREX
6.3.Standards
No. Parameter Criteria
1 Black and (1) Round Shape
White Spots, Zone Acceptable Number
Fore i gn Substance s Dimension ( mm) A B C
D ≦0.1 * * *
0.1
＜ D ≦0.2 3 5 *
0.2
＜ D ≦0.25 2 3 *
0.25＜ D ≦0.3 0 1 *
0.3
＜ D 0 0 *
D = ( Long + Short ) / 2 * : Disregard
(2) Line Shape
Zone Acceptable Number
X (mm) Y (mm) A B C
－ 0.03≧W * * *
2.0≧L 0.05≧W 3 3 *
1.0≧L 0.1
≧W 3 3 *
－ 0.1
＜W In the same way (1)
X : Length Y : Width * : Disregard
Total defects shall not exceed 5.
2 Air Bubbles
(between glass Zone Acceptable Number
& polari zer) Dimen sion (mm) A B C
D ≦ 0.3 * * *
0.3
＜ D ≦ 0.4 3 * *
0.4
＜ D ≦ 0.6 2 3 *
0.6
＜ D 0 0 *
* : Disregard
Total defects shall not exceed 3.
DMF5002NY-EB-AAE (AO) No.99-0199 OPTREX CORPORATION Page 14/17
OPTREX
No. Parameter Criteria
3 The Shape of Dot (1) Dot Shape (with Dent)
As per the sketch of left hand.
(2) Dot Shape (with Projection)
Should not be connec t ed to next do t.
(3) Pin Hole
(X+Y) / 2≦0.2mm
(Less than 0.1mm is no counted.)
(4) Deformation
(X+Y) / 2≦0.2mm
Total acceptable number : 1/dot, 5/cell
(Defect number of (4) : 1pc.)
4 Polarizer Scratches Not to be conspicuous defects.
5 Polarizer Dirts If the stains are removed easily from LCDP surface, the module is not
defective.
6 Complex Foreign Black spots, line shaped foreign substances or air bubbles between
Substance Defects glass & polarizer should be 5pcs maximum in total.
7 Distance between D≦0.2 : 20mm or more
Different Foreign 0.2＜D : 40 mm or more
Substance Defects
0.15≧
Y
X
X
Y
DMF5002NY-EB-AAE (AO) No.99-0199 OPTREX CORPORATION Page 15/17
OPTREX
7.Code System of Production Lot
The production lot of module is specified as follows.
□ □ □ □ □ □
Factory Number (Numeral)
Factory Code (Alphabet)
Production Week (1～5)
Pr oduct ion Month (1～9, X, Y, Z)
Production Year (Lower 2 digits)
8.Type Number
The type number of module is specified on the back of module as fo llows.
ＤＭＦ５００２ＮＹ－ＥＢ－ＡＡＥ
Stamp or Seal
9.Applying Precautions
Please contact us when questions and/or new problems not specified in this specifications arise.
DMF5002NY-EB-AAE (AO) No.99-0199 OPTREX CORPORATION Page 16/17
OPTREX
10.Precautions Relating Product Handling
The Following precautions will guide you in handling our product correctly.
1) Liquid crystal display devices
① The liquid crystal display device panel used in the liquid crystal display module is made of plate
glass. Avoid any strong mechanical shock. Should the glass break handle it with care.
② The polarizer adhering to the surface of the LCD is made of a soft material.
Guard against scratching it.
2) Care of the liquid crystal display module against static electricity discharge.
① When working with the module, be sure to ground your body and any electrical equipment you may
be using. We strongly recommend the use of anti static mats ( made of rubber ), to protect work
tables against the hazards of electrical shock.
② Avoid the use of work c lothing made of synthetic fibers. We recommend co t ton clothing or othe r
conductivity-treated fibers.
③ Slowly and carefully remove the protective film from the LCD module, since this operation can
generate static electricity.
3) When the LCD module alone must be stored for long periods of time:
① Protect the modules from high temperature and humidity.
② Keep the modules out of direct sunlight or direct exposure to ultraviolet rays.
③ Protect the modules from excessive external forces.
4) Use the module with a power supply that is equipped with an overcurrent protector circuit,
since the module is not provided with this protective feature.
5) Do not ingest the LCD fluid itself should it leak out of a damaged LCD module. Should hands
or clothing come in contact with LCD fluid, wash immediately with soap.
6) Conduc1tivity is not guaranteed for models that use metal holders where solder connections
between the metal holder and the PCB are not used. Please contact us to discuss appropriate
ways to assure conductivity.
7) For models which use CFL:
① High voltage of 1000V or greater is applied to the CFL cable connector area.
Care should be taken not to touch connection areas to avoid burns.
② Protect CFL cables from rubbing against the unit and thus causing the wire jacket to become worn.
③The use of CFLs for extended periods of time at low temperatures will significantly shorten their
service life.
DMF5002NY-EB-AAE (AO) No.99-0199 OPTREX CORPORATION Page 17/17
OPTREX
8) For models which use touch pa nels:
①Do not stack up modules since they can be damaged by components on neighboring modules.
②Do not place heavy objects on top of the product. This could cause glass breakage.
9) For models which use COG,TAB,or COF:
①The mechanical strength of the product is low since the IC chip faces out unprotected from the rear.
Be sure to protect the rear of the IC chip from external forces.
②Given the fact that the rear of the IC chip is left exposed, in order to protect the unit from electrical
damage, avoid installation configurations in which the rear of the IC chip runs the risk of making
any electrical contact.
10) Models which use flexible cable, heat seal, or TAB:
①In order to maintain reliability, do not touch or hold by the connector area.
②Avoid any bending, pulling, or other excessive force, which can result in broken connections.
11.Warranty
This product has been manufactured to your comp any’s specifications as a part for use in your company’s
general electronic products. It is guaranteed to perform according to delivery specifications. For any other
use apart from general electronic equipment, we cannot take responsibility if the product is used in medical
devices, nuclear power control equipment, aerospace equipment, fire and security systems, or any other
applications in which there is a direct risk to human life and where extremely high levels of reliability are
required. If the product is to be used in any of the above applications, we will need to enter into a separate
product liability agreement.
① We cannot accept responsibility for any defect, which may arise from additional manufacturing of
the product (including disassembly and reassemb ly), after product delivery.
② We cannot accept respo nsibility for any defect, which may arise after the application of strong
external force to the product.
③ We cannot accept responsibility for any defect, which may arise d ue to the application of static
electricity after the product has passed your comp any’s acceptance inspection procedures.
④ When the product is in CFL models, CFL service life and brightness will vary according to the
performance of the inverter used, leaks, etc. We cannot accept responsibility for product
performance, reliability, or defect, which may arise.
⑤ We cannot accept resp onsibility for industrial property, which may arise through the use of your
pr o duct, with exception to those issues relating directly to the structure or method of
manufacturing of our product.
⑥ Optrex will not be held responsible for any quality guarantee issue for defect products judged as
Optrex-origin longer than 2 (two) years from Optrex production or 1(one) year from Optrex, Optrex
America, Optrex Europe, Display LC delivery which ever comes later.
