Recessed Poke-Throughs Recessed Poke-Throughs Thomas & Betts introduces the Recessed Poke-Through (RPT) series, the only Poke-Through to provide recessed power and communication services. These Poke-Through devices provide the complete protection of receptacles and jacks from impact and abuse. Available in three configurations; quad power receptacle with two communication ports, duplex power with four tele/data ports and a communication Poke-Through device with six ports. The quad configuration is the only two circuit poke-through on the market, allowing greater flexibility for dedicated wiring needs. The attractive brass and aluminum covers provide unmatched good looks. The communication outlets permit an open architecture use with "keystone(R)" jack openings for your data needs. RPT Series Floor Box Features and Benefits: * Available in three configurations - Quad power with two tele/data ports - Duplex power with four tele/data ports - Six tele/data ports only no power - Provides unparalleled flexibility for Poke-Through fittings * Quad configuration comes standard with two 20-A circuits - Only Poke-Through on the market wit two circuit capacity - Allows greater flexibility for dedicated wiring requirements - Can be wired for isolated ground service * Available with metallic brass or aluminum covers - Covers are 100% metallic -not metallic /plastic combination or plated plastic - Provides unmatched aesthetics, durability and strength * Only Poke-Through in the industry to provide "recessed" service - Greatly increases aesthetics of unit while not in use - Provides additional protection of devices from dirt and debris - Complete protection of devices and connectors from impact * Base unit utilizes "One- Step" activation method. - Provides tremendous labor savings at installation - Temporary cover allows installation early in construction phase with finish cover assembly to follow after carpet installation. * Devices are pre-wired at the factory - Eliminates additional wiring by the installer * Junction box factory assembled to 6" long d" EMT conduit - Conduit can easily be changed for different slab depths - Junction box is supplied with 5-d" ko's & 5-f" ko's * Bottom of base unit threaded for conduit on low voltage side - 1" conduit can easily be added for low voltage applications where local codes require or security is necessary * Base unit provides up to 2 hour fire rating in concrete on deck and concrete slab floors * 4" core drill required * Tele/data outlets punched for "keystone(R)" configuration. (R) (R) 77 Recessed Poke-Throughs Recessed Poke-Thru Ordering Information TEMPORARY PROTECTIVE COVER Two Circuit w/four 20A receptacles ( two devices on each circuit) & two communication outlets. Cat. No. RPT-4P2RJ-BRS RPT-4P2RJ-AL RPT-4P2RJ UPPER SMOKE RING LOWER SMOKE RING Recessed Poke-Through Assembly Recessed Poke-Through Assembly Recessed Poke-Through Activation Cover Finish Std. Ctn. Solid Brass Aluminum No Cover 1 1 1 Single circuit w./two 20A receptacles & four communication ports Cat. No. A P P R O X. 1/2" CONDUIT Description 19" RPT-2P4RJ-BRS RPT-2P4RJ-AL RPT-2P4RJ Description Recessed Poke-Through Assembly Recessed Poke-Through Assembly Recessed Poke-Through Activation Cover Finish Std. Ctn. Solid Brass Aluminum No Cover 1 1 1 Six data ports Cat. No. RPT-6RJ RPT-6RJ-BRS RPT-6RJ-AL Description Recessed Poke-Through Assembly Recessed Poke-Through Assembly Recessed Poke-Through Assembly Cover Finish Std. Ctn. No cover Solid Brass Aluminum 1 1 1 Cover Finish Std. Ctn. Solid Brass Aluminum 4 4 27 C.I. JUNCTION BOX Finish Flange Cat. No. RPT-BRS RPT-AL Description Cover & Flange Cover & Flange Knockouts: (2) d" + (1) f"- 2 sides (1) d" + (2) f"- back (1) f"- bottom (R) (R) 78 Modular Poke-Through System More Options Means The T&B Steel City (R) Poke-Through System Fits In Everywhere Today. And Tomorrow. With more materials, colors, and port combinations to choose from, the T&B Steel City(R) Poke-Through System gives you the flexibility you need to meet the demands of changing office environments now and in the future. Our Poke-Through accepts both flush-profile covers and above-floor assemblies. The Steel City(R) Poke-Through's design also makes retrofitting a snap. Choose from a wide variety of metallic and nonmetallic covers and service head fittings to perfectly suit your particular application. Whether using a pre-wired power version or a combination service fitting, the Steel City(R) Poke-Through System will make installation quick and easy and offer the maximum flexibility to adapt to your changing needs. Features Of The T&B Steel City (R) Poke-Through System. * Stainless steel retaining clips prevent rotating, loosening and backing out of lower unit. * Factory assembled junction box allows "drop-in" installation, significantly reducing labor and installation time. * 27 cu. in. junction box capacity allows up to 12 #12 AWG conductors. * Junction box designed with five d" and five f" KOs provide flexibility when installing lower unit. Bottom f" KO allows field adaptability to any floor thickness with use of standard conduit and fittings. * Low voltage channel equivalent to 1b" conduit capacity provide the largest capacity for low voltage cables in the industry. Low voltage channel will accept up to one 50 pair, 24 AWG cable. * Elastomer ring provides cold smoke protection at installation. * Universal mounting system unit allows changes to service fittings without removing lower unit. * Nonmetallic flush covers available in five designer colors. Furnished with duplex flip lids and three data ports. * Nonmetallic furniture feed covers provided with two d" and one f tapped hub and fittings. Available in five designer colors. * Metallic flush covers available in brushed aluminum and polished brass. Furnished with locking flip lids for use with power or voice/data devices. * Low profile Designer Series service fittings (DLP- Series) available in single and double power configurations along with combinations providing both power and communications. Available in gray, ivory or beige. * Built-in slide covers (DLP- Series) protect and enhance the pedestal's appearance while opening easily. * Communication compartment lid flips open when in use and close when not in use (DLP- covers only). * Standard metallic service fittings made from cast aluminum with a brushed aluminum finish. Available in single, two and four gang configurations. * Brushed aluminum face plates face plates are ordered separately, allowing customization for particular applications. See page 80 for full description of available service plates. (R) (R) 79 Modular Poke-Through System Poke-Through System - Base Unit Poke-Through Units with Covers Cat. No. Std. Ctn. Description FPT445-BRS * FPT445-GRY * FPT445-BRN * FPT445-BLK * FPT445-IVY * FPT448-BRS * FPT448-GRY * FPT448-BRN * FPT448-BLK * FPT448-IVY * FPT449 * FPT450 * FPT400B FPT400-DATA FPT-H6-CRT * (1) Base with FPT441-BRS cover; prewired 20A duplex recept. Base with FPT441-GRY cover; prewired 20A duplex recept. Base with FPT441-BRN cover; prewired 20A duplex recept. Base with FPT441-BLK cover; prewired 20A duplex recept. Base with FPT441-IVY cover; prewired 20A duplex recept. Base with FPT442-BRS cover Base with FPT442-GRY cover Base with FPT442-BRN cover Base with FPT442-BLK cover Base with FPT442-IVY cover Base with FPT-CACP cover; prewired 20A duplex recept. Base with FPT-CACP-AL cover; prewired 20A duplex recept. Lower Unit for 3" Core-No Cover Included Data Only Poke-Thru 6-Circuit Furniture Whip Poke-Thru 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 (1) 3/4" and 1" KO for power and data respectively. Junction box has abundant room for splicing (71.5 cu.in.). For use in 3"-6" thick concrete slab or 1d"-3" concrete topped steel deck. * Not CSA certified Covers FPT400 DATA (Cover not included) Cat. No. FPT441 Series Nonmetallic Covers 7" Dia. FPT442 Series Nonmetallic Covers (Two 1/2" Hubs & One 3/4" Hub) 7" Dia. FPT-CACP FPT-CACP-AL Metallic Covers 5 3/4" Dia. FPT441-BRS FPT441-GRY FPT441-BRN FPT441-BLK FPT441-IVY FPT442-BRS FPT442-GRY FPT442-BRN FPT442-BLK FPT442-IVY FPT442 FPT-CACP FPT-CACP-AL FPT-3/4-2-CACP FPT-H6-CRT Std. Ctn. Description Brass Color Nonmetallic Flush Cover-Duplex, Data Ports Gray Color Nonmetallic Flush Cover-Duplex, Data Ports Brown Color Nonmetallic Flush Cover-Duplex, Data Ports Black Color Nonmetallic Flush Cover-Duplex, Data Ports Ivory Color Nonmetallic Flush Cover-Duplex, Data Ports Brass Color Nonmetallic Flush Cover-Conduit Cover Gray Color Nonmetallic Flush Cover-Conduit Cover Brown Color Nonmetallic Flush Cover-Conduit Cover Black Color Nonmetallic Flush Cover-Conduit Cover Ivory Color Nonmetallic Flush Cover-Conduit Cover Flush Top for Furniture Whip-(1) 1" KO & (1) 3/4" KO Duplex, Alum. Metallic Brass Metallic Flush Cover -Duplex Aluminum Metallic Flush Cover -Duplex Brass Metallic Cover with 3/4" and 2" plugs 10 10 10 10 10 10 10 10 10 10 10 10 10 10 (R) (R) 80 Modular Poke-Through System Designer Metallic Service Fittings Cat. No. FPT-400 Series Pedestals FPT401A FPT408A FPT421 FPT422A FPT430 FPT416 FPT423 FPT424 FPT425 FPT426 FPT428 * FPT429 * FPT410A FPT415 Std. Ctn. Description Single Unit; accepts two face plates Low Voltage Separator - single unit Double Unit; accepts four face plates Low Voltage Separator - double unit Quad Unit; accepts eight face plates Adapter for conduit stub ups Communication Faceplate Power, Std. Duplex Faceplate Blank Faceplate Combination Faceplate; token ring data and voice Single Jack Faceplate Double Jack Faceplate Abandonment Plug fits holes 2" to 3" Temporary abandonment kits for lower units 10 10 5 10 1 50 50 50 50 10 50 50 1 10 * Not CSA certified (R) (R) 81