ESD200-B1-CSP0201 Protection device TVS (transient voltage suppressor) Bi-directional, 5.5 V, 6.5 pF, 0201, RoHS and halogen free compliant Feature list * * * * * * * * ESD/transient protection of data lines according to: - IEC61000-4-2 (ESD): 19 kV (air), 17 kV (contact discharge) - IEC61000-4-4 (EFT): 2 kV/40 A (5/50 ns) - IEC61000-4-5 (Surge): 3 A (8/20 s) Bi-directional working voltage up to: VRWM = 5.5 V Line capacitance: CL = 6.5 pF (typical) at f = 1 MHz Clamping voltage: VCL = 13 V (typical) at ITLP = 16 A with RDYN = 0.2 (typical) Very low reverse current: IR < 1 nA (typical) Minimized clamping overshoot due to extremely low parasitic inductance Small form factor SMD size 0201, low profile (0.58 mm x 0.28 mm x 0.15 mm) [3] Bi-directional and symmetric I/V characteristic for optimized design and assembly, recommendations for PCB assembly see [2] Potential applications * ESD protection of highly susceptible IC/ASICs in audio, headset and human digital interfaces Product validation Qualified for industrial applications according to the relevant tests of JEDEC47/20/22 Device information a ) Pin configuration Figure 1 Pin configuration and schematic diagram Table 1 Part information b ) Schematic diagram Type Package Configuration Marking code ESD200-B1-CSP0201 WLL-2-1 1 line, bi-directional A 1) 1 The device has no marking code on the device backside. The marking code is on pad side. Datasheet www.infineon.com Please read the Important Notice and Warnings at the end of this document Revision 1.3 2018-02-19 ESD200-B1-CSP0201 Protection device Table of contents Table of contents Feature list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Potential applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Product validation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Device information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Typical characteristic diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4 4.1 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 WLL-2-1 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Datasheet 2 Revision 1.3 2018-02-19 ESD200-B1-CSP0201 Protection device Maximum ratings 1 Maximum ratings Note: TA = 25 C, unless otherwise specified. Table 2 Maximum ratings Parameter Symbol Values Unit Reverse working voltage VRWM 5.5 V ESD discharge 1) VESD (contact) 17 kV VESD (air) 19 Peak pulse power 2) PPK 45 W Peak pulse current 2) IPP 3 A Operating temperature range TOP -55 to 125 C Storage temperature Tstg -65 to 150 C Attention: Stresses above the maximum values listed here may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Maximum ratings are absolute ratings. Exceeding only one of these values may cause irreversible damage to the component. 1 2 VESD according to IEC61000-4-2 (R = 330 , C = 150 pF discharge network) Stress pulse: 8/20 s current waveform according to IEC61000-4-5 Datasheet 3 Revision 1.3 2018-02-19 ESD200-B1-CSP0201 Protection device Electrical characteristics 2 Note: Electrical characteristics TA = 25 C, unless otherwise specified. Device is electrically symmetrical. IF I PP I TLP VF IF ... Forward voltage VR IR ... Reverse voltage ... Forward current RDYN ... Reverse current V I I V VR VCL VTLP VBR VRWM IT IR IR IT V I RDYN V I I PP I TLP IR Figure 2 Datasheet VRWM VBR VCL VTLP RDYN VRWM VBR VCL VTLP IR IPP ITLP IT VF ... Dynamic resistance ... Reverse working voltage max. ... Breakdown voltage ... Clamping voltage ... TLP voltage ... Reverse leakage current ... Peak pulse current ... TLP current ... Test current Diode_Characteristic_Curve_Bi-directional.svg Definitions of electrical characteristics 4 Revision 1.3 2018-02-19 ESD200-B1-CSP0201 Protection device Electrical characteristics Table 3 DC characteristics Parameter Symbol Values Min. Typ. Unit Note or test condition Max. Breakdown voltage VBR 6 - 10 V IT = 1 mA Reverse current IR - 0.1 100 nA VR = 5.5 V Unit Note or test condition pF VR = 0 V, f = 1 MHz Table 4 AC characteristics Parameter Symbol Values Min. Line capacitance Table 5 CL Typ. - 6.5 - - 6.5 - Symbol Values Min. Clamping voltage 1) VCL Clamping voltage2) Clamping voltage 3) Dynamic resistance 2) 2 3 VR = 0 V, f = 1 GHz ESD and Surge characteristics Parameter 1 Max. RDYN Typ. Unit Note or test condition V VESD = 8 kV, contact discharge Max. - 12 - - 10 - ITLP = 1 A, tp = 100 ns - 13 - ITLP = 16 A, tp = 100 ns - 10 - IPP = 1 A, tp = 8/20 s - 12.5 - IPP = 3 A, tp = 8/20 s - 0.2 - tp = 100 ns VESD according to IEC61000-4-2 (R = 330 , C = 150 pF discharge network) Please refer to application note AN210 [1], TLP parameters: Z0 = 50 , tp = 100 ns, tr = 0.6 ns Stress pulse: 8/20 s current waveform according to IEC61000-4-5 Datasheet 5 Revision 1.3 2018-02-19 ESD200-B1-CSP0201 Protection device Typical characteristic diagrams 3 Note: Typical characteristic diagrams TA = 25 C, unless otherwise specified. 10-3 10 -4 10-5 IR [A] 10-6 10-7 10 10 Figure 3 -8 -9 10 -10 10 -11 10 -12 -10 -8 -6 -4 -2 0 VR [V] 2 4 6 8 10 Reverse leakage current: IR = f(VR) IR [nA] 10+1 10+0 -1 10 Figure 4 Datasheet -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 TA [C] Reverse current IR = f(TA), VR = 5.5 V 6 Revision 1.3 2018-02-19 ESD200-B1-CSP0201 Protection device Typical characteristic diagrams 9 8.9 8.8 VBR [V] 8.7 8.6 8.5 8.4 8.3 8.2 8.1 8 -40 -30 -20 -10 0 Figure 5 10 20 30 40 50 60 70 80 90 100 110 120 130 TA [C] Reverse voltage VBR = f(TA), IBR = 1 mA 10 9 8 CL [pF] 7 1 MHz 6 5 1 GHz 4 3 2 1 0 Figure 6 Datasheet -3 -2.5 -2 -1.5 -1 -0.5 0 0.5 VR [V] 1 1.5 2 2.5 3 Line capacitance: CL = f(VR), f = 1 MHz, 1 GHz 7 Revision 1.3 2018-02-19 ESD200-B1-CSP0201 Protection device Typical characteristic diagrams 50 Scope: 6 GHz, 20 GS/s 45 VCL [V] 40 35 VCL-max-peak = 25 V 30 VCL-30ns-peak = 12 V 25 20 15 10 5 0 -5 -100 Figure 7 0 100 200 300 400 tp [ns] 500 600 700 800 900 Clamping voltage (ESD): VCL = f(t), 8 kV positive pulse according to IEC61000-4-2 5 0 -5 -10 VCL [V] -15 -20 -25 -30 VCL-max-peak = -24 V -35 VCL-30ns-peak = -11 V -40 -45 -50 -100 Figure 8 Datasheet Scope: 6 GHz, 20 GS/s 0 100 200 300 400 tp [ns] 500 600 700 800 900 Clamping voltage (ESD): VCL = f(t), 8 kV negative pulse according to IEC61000-4-2 8 Revision 1.3 2018-02-19 ESD200-B1-CSP0201 Protection device Typical characteristic diagrams 50 Scope: 6 GHz, 20 GS/s 45 VCL [V] 40 35 VCL-max-peak = 34 V 30 VCL-30ns-peak = 13 V 25 20 15 10 5 0 -5 -100 Figure 9 0 100 200 300 400 tp [ns] 500 600 700 800 900 Clamping voltage (ESD): VCL = f(t), 15 kV positive pulse according to IEC61000-4-2 5 0 -5 -10 VCL [V] -15 -20 -25 -30 VCL-max-peak = -35 V -35 VCL-30ns-peak = -12 V -40 -45 -50 -100 Figure 10 Datasheet Scope: 6 GHz, 20 GS/s 0 100 200 300 400 tp [ns] 500 600 700 800 900 Clamping voltage (ESD): VCL = f(t), 15 kV negative pulse according to IEC61000-4-2 9 Revision 1.3 2018-02-19 ESD200-B1-CSP0201 Protection device Typical characteristic diagrams 30 15 ESD200-B1-CSP0201 RDYN 25 12.5 20 10 15 7.5 RDYN = 0.20 5 5 2.5 0 0 -5 -2.5 -10 Equivalent VIEC [kV] ITLP [A] 10 -5 RDYN = 0.20 -15 -7.5 -20 -10 -25 -12.5 -30 -20 -15 -10 -5 0 5 10 15 -15 20 VTLP [V] Figure 11 Datasheet Clamping voltage (TLP): ITLP = f(VTLP) [1] 10 Revision 1.3 2018-02-19 ESD200-B1-CSP0201 Protection device Typical characteristic diagrams 5 4 3 2 IPP [A] 1 0 -1 -2 -3 -4 -5 -20 Figure 12 Datasheet -15 -10 -5 0 VCL [V] 5 10 15 20 Clamping voltage (Surge): IPP = f(VCL) according to IEC61000-4-5 [1] 11 Revision 1.3 2018-02-19 ESD200-B1-CSP0201 Protection device Typical characteristic diagrams 0 Insertion Loss [dB] -5 -10 -15 -20 -25 ESD200-B1-CSP0201 -30 -35 Figure 13 Datasheet 10 100 1000 f [MHz] 10000 Insertion loss versus frequency in a 50 system 12 Revision 1.3 2018-02-19 ESD200-B1-CSP0201 Protection device Package information 4 Package information 4.1 WLL-2-1 package Note: Dimensions in mm Top view Bottom view 0.15 0.01 0.28 0.03 0.58 0.03 (0.16) 1 0.2 0.02 0.36 2 0.26 0.02 SG-WLL-2-1-PO V01 WLL-2-1 package outline 0.19 0.24 Solder mask 0.19 0.57 0.62 Copper 0.19 0.27 0.14 0.32 0.24 Figure 14 Stencil apertures SG-WLL-2-1-FP V01 Figure 15 WLL-2-1 footprint 8 0.68 0.23 2 0.21 0.35 SG-WLL-2-1-TP V02 Figure 16 WLL-2-1 packing Marking on pad-side Type code 1 12 12 Figure 17 Datasheet Type code 1 WLL-2-1 marking example (marking code see Device information ) 13 Revision 1.3 2018-02-19 ESD200-B1-CSP0201 Protection device References 5 References [1] Infineon AG - Application note AN210: Effective ESD protection design at system level using VF-TLP characterization methodology [2] Infineon AG - Recommendations for Printed Circuit Board Assembly of Infineon WLL Packages http://www.infineon.com/Packageinformation_WLL [3] Infineon AG - Application note AN392: TVS diodes in ChipScalePackage reduce size and save cost Revision history Revision history: Rev. 1.2. 2016-05-13 Page or Item Subjects (major changes since previous revision) Revision 1.3, 2018-02-19 All Data sheet layout changed References updated, editorial changes Datasheet 14 Revision 1.3 2018-02-19 Trademarks All referenced product or service names and trademarks are the property of their respective owners. Edition 2018-02-19 Published by Infineon Technologies AG 81726 Munich, Germany (c) 2018 Infineon Technologies AG All Rights Reserved. Do you have a question about any aspect of this document? Email: erratum@infineon.com Document reference IFX-sws1502286912666 IMPORTANT NOTICE The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics ("Beschaffenheitsgarantie") . With respect to any examples, hints or any typical values stated herein and/or any information regarding the application of the product, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. In addition, any information given in this document is subject to customer's compliance with its obligations stated in this document and any applicable legal requirements, norms and standards concerning customer's products and any use of the product of Infineon Technologies in customer's applications. The data contained in this document is exclusively intended for technically trained staff. It is the responsibility of customer's technical departments to evaluate the suitability of the product for the intended application and the completeness of the product information given in this document with respect to such application. WARNINGS Due to technical requirements products may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies office. Except as otherwise explicitly approved by Infineon Technologies in a written document signed by authorized representatives of Infineon Technologies, Infineon Technologies' products may not be used in any applications where a failure of the product or any consequences of the use thereof can reasonably be expected to result in personal injury