ICS664G-01LF - Integrated Device Technology

ICS664-01

MDS 664-01 A 1Revision 050704

Integrated Circuit Systems, Inc. ● 525 Race Street, San Jose, CA 95126 ● tel (408) 297-1201 ● www.icst.com

Digital Video Clock Source

Description

The ICS664-01 provides clock generation and

conversion for clock rates commonly needed in HDTV

digital video equipment. The ICS664-01 uses the latest

PLL technology to provide excellent phase noise and

long term jitter performance for superior

synchronization and S/N ratio.

For audio sampling clocks generated from 27 MHz, use

the ICS661.

Please contact ICS if you have a requirement for an

input and output frequency not included in this

document. ICS can rapidly modify this product to meet

special requirements.

Features

•Packaged in 16-pin TSSOP

•Clock or crystal input provides flexibility

•Low phase noise supports enhanced SNR

•Lowest jitter in class at 100 ps

•Exact (0 ppm) multiplication ratios

•Power-down mode lowers power consumption

•Improved phase noise over ICS660

Block Diagram

PLL Clock

Synthesis

SELIN

Crystal

Oscillator

X1/REFIN

VDD (P2) VDD (P14)

CLK

GND (P13) GND (P6) GND (P5)

S3:0 4

VDD (P3) VDDO

Digital Video Clock Source

MDS 664-01 A 2Revision 050704

Integrated Circuit Systems, Inc.● 525 Race Street, San Jose, CA 95126 ● tel (408) 297-1201 ● www.icst.com

ICS664-01

Pin Assignment

16-pin TSSOP

Output Clock Selection Table

Pin Descriptions

X1/REFIN X2

VDD

N/C

VDD

GND

SELIN

VDDO

S3 S1

S2 CLK

S3 S2 S1 S0

Input

Frequency

(MHz)

Output

Frequency

(MHz)

0000 Power down

0001 Pass thru Input Freq

0010 27 74.25

0011 27 74.175824

0100 13.5 74.25

0101 13.5 74.175824

0110RESERVEDRESERVED

0111RESERVEDRESERVED

1000 74.25 54

100174.175824 54

1010RESERVEDRESERVED

1011RESERVEDRESERVED

1100 54 74.25

1101 54 74.175824

1110 54 13.5

1111 27 13.5

Number

Name

Type Pin Description

1 X1/REFIN Input Connect this pin to a crystal or clock input

2 VDD Power Power supply for crystal oscillator.

3 VDD Power Power supply for PLL.

4 S0 Input Output frequency selection. Determines output frequency per table above. On chip pull up.

5 GND Power Ground for output stage.

6 GND Power Ground for PLL.

7 S3 Input Output frequency selection. Determines output frequency per table above. On chip pull up.

8 S2 Input Output frequency selection. Determines output frequency per table above. On chip pull up.

9 CLK Output Clock output.

10 S1 Input Output frequency selection. Determines output frequency per table above. On chip pull up.

11 VDDO Power Power supply for output stage.

12 SEL Input Low for clock input, high for crystal. On chip pull up.

13 GND Power Connect to ground.

14 VDD Power Power supply.

15 NC — No connect. Do not connect to anything.

16 X2 Input Connect this pin to a crystal. Leave open if using a clock input.

Digital Video Clock Source

MDS 664-01 A 3Revision 050704

Integrated Circuit Systems, Inc.● 525 Race Street, San Jose, CA 95126 ● tel (408) 297-1201 ● www.icst.com

ICS664-01

Application Information

Series Termination Resistor

Clock output traces should use series termination. To

series terminate a 50Ω trace (a commonly used trace

impedance), place a 33Ω resistor in series with the

clock line, as close to the clock output pin as possible.

The nominal impedance of the clock output is 20Ω.

Decoupling Capacitors

As with any high-performance mixed-signal IC, the

ICS664-01 must be isolated from system power supply

noise to perform optimally.

Decoupling capacitors of 0.01µF must be connected

between each VDD and the PCB ground plane. To

further guard against interfering system supply noise,

the ICS664-01 should use one common connection to

the PCB power plane as shown in the diagram on the

next page. The ferrite bead and bulk capacitor help

reduce lower frequency noise in the supply that can

lead to output clock phase modulation.

Recommended Power Supply Connection for

Optimal Device Performance

All power supply pins must be connected to the same

voltage, except VDDO, which may be connected to a

lower voltage in order to change the output level.

Crystal Load Capacitors

If a crystal is used, the device crystal connections

should include pads for capacitors from X1 to ground

and from X2 to ground. These capacitors are used to

adjust the stray capacitance of the board to match the

nominally required crystal load capacitance. To reduce

possible noise pickup, use very short PCB traces (and

no vias) been the crystal and device.

The value of the load capacitors can be roughly

determined by the formula C = 2(CL - 6) where C is the

load capacitor connected to X1 and X2, and CL is the

specified value of the load capacitance for the crystal.

A typical crystal CL is 18 pF, so C = 2(18 - 6) = 24 pF.

Because these capacitors adjust the stray capacitance

of the PCB, check the output frequency using your final

layout to see if the value of C should be changed.

PCB Layout Recommendations

For optimum device performance and lowest output

phase noise, the following guidelines should be

observed.

1) Each 0.01µF decoupling capacitor should be

mounted on the component side of the board as close

to the VDD pin as possible. No vias should be used

between decoupling capacitor and VDD pin. The PCB

trace to VDD pin should be kept as short as possible,

as should the PCB trace to the ground via. Distance of

the ferrite bead and bulk decoupling from the device is

less critical.

2) The external crystal should be mounted next to the

device with short traces. The X1 and X2 traces should

not be routed next to each other with minimum spaces,

instead they should be separated and away from other

traces.

3) To minimize EMI and obtain the best signal integrity,

the 33Ω series termination resistor should be placed

close to the clock output.

4) An optimum layout is one with all components on the

same side of the board, minimizing vias through other

signal layers (the ferrite bead and bulk decoupling

capacitor can be mounted on the back). Other signal

traces should be routed away from the ICS664-01. This

includes signal traces just underneath the device, or on

layers adjacent to the ground plane layer used by the

device.

Connection to 3.3V

Power Plane

Ferrite

Bead

Bulk Decoupling Capacitor

(such as 1 F Tantalum)

VDD Pin

0.01 F Decoupling Capacitors

Digital Video Clock Source

MDS 664-01 A 4Revision 050704

Integrated Circuit Systems, Inc.● 525 Race Street, San Jose, CA 95126 ● tel (408) 297-1201 ● www.icst.com

ICS664-01

Absolute Maximum Ratings

Stresses above the ratings listed below can cause permanent damage to the ICS664-01. These ratings,

which are standard values for ICS commercially rated parts, are stress ratings only. Functional operation of

the device at these or any other conditions above those indicated in the operational sections of the

specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can

affect product reliability. Electrical parameters are guaranteed only over the recommended operating

temperature range.

Recommended Operation Conditions

DC Electrical Characteristics

Unless stated otherwise, VDD = 3.3 V ±10%, Ambient Temperature 0 to +70° C

Item Rating

Supply Voltage, VDD 5.5 V

All Inputs and Outputs -0.5 V to VDD+0.5 V

Ambient Operating Temperature 0 to +70°C

Storage Temperature -65 to +150°C

Junction Temperature 125°C

Soldering Temperature 260°C

Parameter Min. Typ. Max. Units

Ambient Operating Temperature 0 +70 °C

Power Supply Voltage (measured in respect to GND) +3.0 +3.6 V

Parameter Symbol Conditions Min. Typ. Max. Units

Operating Voltage

VDD 3.0 3.6 V

VDDO 2.5 VDD V

Supply Current IDD No Load 35 mA

Input High Voltage VIH 2V

Input Low Voltage VIL 0.8 V

Output High Voltage VOH IOH = -4 mA VDD-0.4 V

Output High Voltage VOH IOH = -20 mA 2.4 V

Output Low Voltage VOL IOL = 20 mA 0.4 V

Short Circuit Current IOS Each output ±65 mA

Nominal Output Impedance ZOUT 20 Ω

Input Capacitance CIN Input pins 7 pF

Internal Pull-up Resistor RPU 120 kΩ

Digital Video Clock Source

MDS 664-01 A 5Revision 050704

Integrated Circuit Systems, Inc.● 525 Race Street, San Jose, CA 95126 ● tel (408) 297-1201 ● www.icst.com

ICS664-01

AC Electrical Characteristics

Unless stated otherwise, VDD = 3.3 V ±10%, Ambient Temperature 0 to +70° C

Thermal Characteristics

Parameter Symbol Conditions Min. Typ. Max. Units

Crystal Frequency 28 MHz

Output Clock Rise Time tOR 20% to 80%, 15 pF load 1.5 ns

Output Clock Fall Time tOF 80% to 20%, 15 pF load 1.5 ns

Output Duty Cycle tOD at VDD/2, 15 pF load 40 49 to 51 60 %

Power-up Time tPU

Valid power on to valid

output 1ms

Power-down Time tPD

Power off to clock

disable 10 µs

Jitter, short term 100 ps p-p

Jitter, long term 10 µs delay 200 ps p-p

Single Sideband Phase

Noise 10 kHz offset -120 dBc

Actual Mean Frequency

Error versus Target

0ppm

Parameter Symbol Conditions Min. Typ. Max. Units

Thermal Resistance Junction to

Ambient

θJA Still air 78 °C/W

θJA 1 m/s air flow 70 °C/W

θJA 3 m/s air flow 68 °C/W

Thermal Resistance Junction to Case θJC 37 °C/W

Digital Video Clock Source

MDS 664-01 A 6Revision 050704

Integrated Circuit Systems, Inc.● 525 Race Street, San Jose, CA 95126 ● tel (408) 297-1201 ● www.icst.com

ICS664-01

Package Outline and Package Dimensions (16-pin TSSOP, 4.40 mm Body, 0.65 mm Pitch)

Package dimensions are kept current with JEDEC Publication No. 95, MO-153

Ordering Information

While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems (ICS)

assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would

result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial

applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary

environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any

circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or

critical medical instruments.

Part / Order Number Marking Shipping

packaging Package Temperature

ICS664G-01 ICS664G-01 Tubes 16-pin TSSOP 0 to +70° C

ICS664G-01T ICS664G-01 Tape and Reel 16-pin TSSOP 0 to +70° C

INDEX

AREA

1 2

E1 E

SEATING

PLANE

- C -

aaa C

Millimeters Inches

Symbol Min Max Min Max

A--1.20--0.047

A1 0.05 0.15 0.002 0.006

A2 0.80 1.05 0.032 0.041

b 0.19 0.30 0.007 0.012

C 0.09 0.20 0.0035 0.008

D 4.90 5.1 0.193 0.201

E 6.40 BASIC 0.252 BASIC

E1 4.30 4.50 0.169 0.177

e 0.65 Basic 0.0256 Basic

L 0.45 0.75 0.018 0.030

α0°8°0°8°

aaa -- 0.10 -- 0.004