Freescale Semiconductor User's Guide Document Number: KT33812UG Rev. 2.0, 7/2009 KIT33812EKEVBE Evaluation Board Figure 1. KIT33812EKEVBE Evaluation Board Table of Contents 1 Kit Contents / Packing List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 Important Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3 Kit Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4 Required Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 5 EVB Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 6 Using Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 7 EVB Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 8 Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 9 KIT33812EKEVBE Bill of Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 10 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 11 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 (c) Freescale Semiconductor, Inc., 2009. All rights reserved. Kit Contents / Packing List 1 Kit Contents / Packing List * * KIT33812EKEVBE Evaluation Board CD33812 KIT33812EKEVBE Evaluation Board, Rev. 2.0 2 Freescale Semiconductor Important Notice 2 Important Notice Freescale provides the enclosed product(s) under the following conditions: This evaluation kit is intended for use of ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY. It is provided as a sample IC pre-soldered to a printed circuit board to make it easier to access inputs, outputs, and supply terminals. This EVB may be used with any development system or other source of I/O signals by simply connecting it to the host MCU or computer board via off-the-shelf cables. This EVB is not a Reference Design and is not intended to represent a final design recommendation for any particular application. Final device in an application will be heavily dependent on proper printed circuit board layout and heat sinking design as well as attention to supply filtering, transient suppression, and I/O signal quality. The goods provided may not be complete in terms of required design, marketing, and or manufacturing related protective considerations, including product safety measures typically found in the end product incorporating the goods. Due to the open construction of the product, it is the user's responsibility to take any and all appropriate precautions with regard to electrostatic discharge. In order to minimize risks associated with the customers applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. For any safety concerns, contact Freescale sales and technical support services. Should this evaluation kit not meet the specifications indicated in the kit, it may be returned within 30 days from the date of delivery and will be replaced by a new kit. Freescale reserves the right to make changes without further notice to any products herein. Freescale makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typical", must be validated for each customer application by customer's technical experts. Freescale does not convey any license under its patent rights nor the rights of others. Freescale products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale was negligent regarding the design or manufacture of the part.FreescaleTM and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. (c) Freescale Semiconductor, Inc., 2009. All rights reserved. KIT33812EKEVBE Evaluation Board, Rev. 2.0 Freescale Semiconductor 3 Kit Introduction 3 Kit Introduction KIT33812EKEVBE Evaluation Board (EVB) is an easy-to-use circuit board used to exercise all the functions of the MC33812 Multifunctional Ignition and Injector Driver. A Personal Computer (PC) communicates to the EVB through a USB/SPI Dongle (KITUSBSPIDGLEVME) connected to the PC's USB port. The Freescale SPIGen program provides the user Interface to the MC33812 EVB's SPI port and is used to send commands to the IC. 3.1 EVB Features * * * * * * * * * * * * * * * Designed to operate over the range of ~4.7V VPWR 36V Fuel Injector driver - Current Limit - 4.0A Typical Ignition pre-driver can drive IGBT or Darlington bipolar junction transistor Ignition pre-driver has independent high and low side outputs Relay driver - Current Limit - 4.0A Typical Lamp driver- Current Limit - 1.5A Typical All external outputs protected against short to battery, over-current Ignition and other drivers protected against over-temperature Interfaces directly to MCU Using 5.0V parallel interface VCC voltage pre-regulator provides +5.0V power for MCU MCU Power On RESET generator MCU watchdog timer circuit with parallel refresh/time setting line Independent fault annunciation outputs for ignition and injection ISO-9141 K-Line transceiver for communicating diagnostic messages Pb-free packaging designated by suffix code EK KIT33812EKEVBE Evaluation Board, Rev. 2.0 4 Freescale Semiconductor Required Equipment 4 Required Equipment Minimum required equipment: * * * * * * Power supply: 5.5 to 18V USB-SPI Dongle USB Cable 16-wire ribbon cable with 16 pins ribbon cable connectors on both sides USB enabled computer with Windows XP SPIGen software (Setup.exe) KIT33812EKEVBE Evaluation Board, Rev. 2.0 Freescale Semiconductor 5 EVB Block Diagram 5 EVB Block Diagram MC33812 SMALL ENGINE CONTROL EVB BLOCK DIAGRAM VBAT + 12V - VPWR LED Reverse Battery and Transient Protection VPWR IGNITION SUPPLY JUMPER VCC (+5V) VCC LED VCC (+5V) 8 VPWR 6 IGNSUP 3 4 IGNFB 2 IGNOUTH 1 IGNOUTL VCCSENS VCC PASS TRANSISTOR 7 VCCREF OUTPUTS VPWR IGNITION LED IGBT and Feedback divider 29 LAMP OUTPUT WD_INH INJECTOR LED INPUTS INJOUT USB/SPI Dongle Connector 19 INJECTOR OUTPUT RELAY LED WDRFSH ROUT DATA4 17 DATA3 15 DATA2 14 RIN DATA1 DATA0 16 16 13 IGNIN INJIN VPWR 27 MC33812 2 WDRFSH CNTL0 15 VPWR LAMPOUT 24 1 WD_INH JUMPER 3 USB ON LED IGNITION COIL OUTPUT LAMP LED SOFT VCC 1 VPWR VPWR 22 RELAY OUTPUT MTX LAMPIN RESETB 9 INJFLT 10 11 RELFLT 12 IGNFLT 18 MRX RESET LED 6 RESETB INJ. FAULT LED INJFLT REL. FAULT LED RELFLT IGN. FAULT LED IGNFLT MRX STATE LED MRX GND 1 N/C 32 TEST3 31 TEST2 30 TEST1 20 TM_EN 3 1 VPWR ISO9141 5 GNDs ISO 9141 CONNECTOR LIN_PWR 4 2 23, 25, 26, EP Figure 1. EVB Block Diagram KIT33812EKEVBE Evaluation Board, Rev. 2.0 6 Freescale Semiconductor Using Hardware 6 Using Hardware This EVB consists of a MC33812 Small Engine Control Circuit, a USB to SPI Dongle interface, power conditioning circuitry, and a set of Input Select Jumpers. All +5 volt VCC power required by the EVB is obtained from the MC33812 built-in power regulator. 6.1 LED Display Twelve LED's are provided as visual output devices for the MC33812 EVB board. A list of the LED devices is shown below: 1. VPWR LED - Indicates when +12V supply is connected to the EVB. 2. VCC LED - Indicates that the MC33812 internal +5V regulator is running and providing the +5V VCC voltage supply 3. IGNITION LED - Indicates that the Ignition Input, IGNIN, is active and the Ignition Output driver is turned on. 4. LAMP LED - Indicates that the Lamp Input, LAMPIN, is active and the Lamp Output is pulled low. 5. INJECTOR LED - Indicates that the Injector Input, INJIN, is active and the Injector Output is pulled low. 6. RELAY LED - Indicates that the Relay Input, RIN, is active and the Relay Output is pulled low. 7. RESET LED - Indicates that the RESETB output logic level is active (low). 8. INJECTOR FAULT LED - Indicates that there is either a short to Battery, Open Load or other fault on the Injector output. 9. RELAY FAULT LED - Indicates that there is either a short to Battery, Open Load or other fault on the Relay output. 10. IGNITION FAULT LED - Indicates that there is either a short to Battery, Open Load or other fault on the Ignition IGBT output. 11. MRX STATE LED - Indicates the state of the MRX line as a result of the data on the ISO9141 line. 12. USB ON LED - Indicates that the USB SPI dongle is connected properly and is attached to an active USB port on a PC. 6.2 Selection Jumper Definitions The EVB contains four jumpers that provide certain selections for the MC33812 as follows (Bold = default factory setting): JUMPER NAME WD_INH WDRFSH LIN_PWR IGNITION SUPPLY 6.2.1 JUMPER POSITION 1-2 / 2-3 OFF/ON OFF/ON 1 -2 /2 - 3 / CONNECTION +5V PU/GND OPEN/CNTL0 FLOAT/VPWR VCC/VPWR WD_INH Jumper The WD_INH is the Watch Dog Inhibit enable/disable setting jumper. With a shorting jumper between pins 1 and 2, the WD_INH pin on the MC33812 is pulled high through a 4.7K resistor to +5 V, causing the Watch Dog circuit to be disabled. With the shorting jumper between pins 2 and 3, or left off, the WD_INH pin on the MC33812 is pulled to GND, enabling the Watch Dog circuit. KIT33812EKEVBE Evaluation Board, Rev. 2.0 Freescale Semiconductor 7 Using Hardware 6.2.2 WDRFSH Jumper The WDRFSH jumper provides a connection from the MC33812's WDRFSH line to the CNTL0 output from the USB/SPI Dongle interface. The WDRFSH line is the logic input that "Pets" the Watch Dog timer circuit, preventing it from issuing a RESET signal when the Watch Dog times out Placing a shorting jumper between pins 1 and 2 connects the CNTL0 signal from the USB/SPI interface to this WDRFSH pin on the MC33812 circuit. Removing the jumper provides access to the WHDRFSH pin on the MC33812 circuit (on jumper pin 1) to allow other external pulse generators or logic outputs to drive this Watch Dog reloading input. 6.2.3 LIN_PWR Jumper The LIN_PWR jumper allows the user to place VPWR on pin 3 of the ISO9141 connector. With a shorting jumper in place the VPWR supply is connected to pin 3 of the ISO9141 connector. With the jumper removed, pin 3 of the ISO9141 connector is left floating. 6.2.4 IGNITION SUPPLY Jumper The MC33812 Ignition Outputs (IGNOUTL and IGNOUTH) are capable of driving either an IGBT transistor or a Darlington transistor to control a spark coil. The IGNITION SUPPLY selector jumper connects either the VCC supply or the VPWR supply to the MC33812's IGNSUP pin to provide the proper voltage for driving the chosen output transistor type. When a Darlington transistor is being used to drive the spark coil, the IGNITION SUPPLY Jumper should be placed on pins 1 and 2 to select VCC as the Ignition Supply, IGNSUP. When an IGBT is the transistor of choice, to drive the spark coil, the IGNITION SUPPLY Jumper should be placed on pins 2 and 3 (the factory default setting) to select VPWR as the Ignition Supply Voltage, IGNSUP, to be able to fully enhance the IGBT's gate. The factory supplied IGBT can be replaced with a darlington transistor, if desired, however resistors R11 and R13 will need to be changed to provide the additional drive current required by the darlington transistor. 6.2.5 Input Signal Definitions The MC33812 has six logic level input signals that are used to control certain outputs or functions inside the circuit. These six signals are: 1. WDRFSH - Reloads the Watch Dog to prevent issuing a RESET 2. MTX - Provides the transmit data to the ISO9141 line 3. LAMPIN - Controls the state of the LAMPOUT output 4. RIN - Controls the state of the ROUT output 5. IGNIN - Controls the state of the IGNOUTH and IGNOUTL outputs 6. INJIN - Controls the state of the INJOUT output These six signals are provided by six of the parallel outputs from the USB/SPI interface as described below: 1. WDRFSH - Connected to the CNTL0 signal KIT33812EKEVBE Evaluation Board, Rev. 2.0 8 Freescale Semiconductor Using Hardware 2. MTX - Connected to the DATA4 signal 3. LAMPIN - Connected to the DATA3 signal 4. IN - Connected to the DATA2 signal 5. IGNIN - Connected to the DATA1 signal 6. INJIN - Connected to the DATA0 signal DATA0 -DATA4 and CNTL0 signals are parallel outputs from the USB/SPI Dongle that can be controlled directly from the SPIGen program. An example config file called "MCZ33812_EVB_CONFIGURATION_FILE.spi" is provided on the CD which contains several batch file examples. If the user prefers to supply the various MC33812 input signals externally, other than from the USB-SPI Interface, the connections are available on the connector listed below. 6.2.6 USB/SPI Dongle Connector The USB/SPI dongle connector is a 16 pin,.1" center, dual-row connector that is designed to interface directly to the USB/SPI Dongle unit. The USB/SPI dongle connector consists of the following 16 pins - Pin Number 1* 2* 3* 4* 5* 6 7* 8 9* 10 11 12 13* 14 15 16 Name CSB CNTL2 SO CNTL1 SI CNTL0 SCLK DATA4 CNTL3 DATA3 VDD DATA2 +3.3V DATA1 GND DATA0 Description SPI signal, Chip Select Bar Parallel port signal CNTL2 SPI signal, Serial Out Parallel port signal CNTL1 SPI signal, Serial In Parallel port signal CNTL0 SPI signal, Serial Clock Parallel port signal DATA4 Parallel port signal CNTL3 Parallel port signal DATA3 +5 Volt VDD from USB Parallel port signal DATA2 +3.3 V from USB Parallel port signal DATA1 Signal Ground Parallel port signal DATA0 Notes: * These connections are unused in this EVB. This connector mates with the 16 conductor flat cable that connects to the USB/SPI Dongle (KITUSBSPIDGLEVME). KIT33812EKEVBE Evaluation Board, Rev. 2.0 Freescale Semiconductor 9 Using Hardware 6.2.7 Screw Terminal Connections The MC33812 board contains four output and one input screw terminal connections to allow easy access to the MC33812's circuits. The diagram below shows the locations of the screw terminals and their functional definitions: IGNITION OUT LAMP OUT VBAT INJECTOR OUT VCC VCC RELAY OUT ISO9141 Figure 2. MC33812 EVB Screw Connectors 6.2.8 VBAT Input Connector The VBAT Connector is a 2 position screw terminal that provides +12 Volt and Ground Terminals. The Ground terminal is marked "GND" and the +12 Volt Terminal is marked "VBAT". 6.2.9 ISO 9141 Connector The ISO9141 connector is a four pin Input/Output connector that provides power, ground and the ISO9141 bidirectional signal. 6.2.10 Output Connectors There are four Output Connectors which are 2 position screw terminals that provides the following signals: 1. 1) IGNITION OUT * Screw Terminal 1 - Low side drive, IGNOUT * Screw Terminal 2 - VPWR 2. 2) LAMP OUT * Screw Terminal 1 - Low Side LAMPOUT * Screw Terminal 2 - VPWR KIT33812EKEVBE Evaluation Board, Rev. 2.0 10 Freescale Semiconductor Using Hardware 3. 3) INJECTOR OUT * Screw Terminal 1 - Low side INJOUT * Screw Terminal 2 - VPWR 4. 4) RELAY OUT * Screw Terminal 1 - LOW side ROUT * Screw Terminal 2 - VPWR 6.2.11 MC33812 EVB Setup and Example Demonstrations To perform the examples included in the CD the following connections and setup must be performed: 1. Make sure the SPIGen 5.0X program is installed on the PC and it can communicate with the USB/SPI Dongle as described in that kit's documentation. 2. Connect the USB/SPI Dongle to the MC33812 EVB via a 16 pin ribbon cable. Make sure to orient the cable so that pin1 on both the USB/SPI Dongle and the MC33812 EVB are connected correctly, pin 1 to pin 1. 3. Connect the USB/SPI Dongle to a PC, LED 2 on the USB/SPI Dongle and the USB ON LED on the MC33812 board should both be illuminated. 4. Attach a +12 VDC supply (do not turn on power yet) to the VBAT connector on the MC33812 EVB, making sure to observe the GND and +12V terminals. The current capability of the +12V supply should exceed the maximum total current that the number of simultaneously ON loads will require. 5. Attach loads to the IGNITION OUT, LAMP OUT, INJECTOR OUT and RELAY OUT and ISO9141 terminals as appropriate. 6. Launch SPIGen and from the "File" menu, select "Open" and browse to the CD containing the "MCZ33812_EVB_CONFIGURATION_FILE.spi" file. The title on the SPIGen screen should change from "Generic SPI Generator" to "MC33812 SPI Generator". 7. Turn on the +12 Volt Supply. Verify that all is working correctly by observing the VPWR and VCC LEDs which should be illuminated. Click on the "Extra Pins" button in the SPIGen main screen and then click on the following buttons: 8. Click on the Data 0 "High" button. The INJECTOR load and LED should turn on. Clicking on the DATA 0 "Low" button should turn off the load and LED. 9. Click on the Data 1 "High" button. The IGNITION load and LED should turn on. Clicking on the DATA 1 "Low" button should turn off the IGNITION load and LED. 10. Click on the Data 2 "High" button. The RELAY load and LED should turn on. Clicking on the DATA 2 "Low" button should turn off the RELAY load and LED. 11. Click on the Data 3 "High" button. The LAMP load and LED should turn on. Clicking on the DATA 3 "Low" button should turn off the LAMP load and LED. 12. Click on the Data 4 "High" button. The ISO9141 load should turn on. Clicking on the DATA 3 "Low" button should turn off the ISO9141 load. If everything described so far occurs then you are ready to proceed with the remaining examples. KIT33812EKEVBE Evaluation Board, Rev. 2.0 Freescale Semiconductor 11 EVB Schematic EVB Schematic VCC VCC VCC VCC 7 Figure 3. EVB Schematic KIT33812EKEVBE Evaluation Board, Rev. 2.0 12 Freescale Semiconductor Board Layout 8 Board Layout 8.1 Assembly Drawing VCC VCC Figure 4. Assembly Drawing KIT33812EKEVBE Evaluation Board, Rev. 2.0 Freescale Semiconductor 13 Board Layout 8.2 PCB Top Layer Figure 5. PCB Top Layer KIT33812EKEVBE Evaluation Board, Rev. 2.0 14 Freescale Semiconductor Board Layout 8.3 PCB Bottom Layer Figure 6. PCB Bottom Layer KIT33812EKEVBE Evaluation Board, Rev. 2.0 Freescale Semiconductor 15 KIT33812EKEVBE Bill of Material 9 KIT33812EKEVBE Bill of Material Value Package Mfr. Mfr. Part # Digi-Key Part # Location Orienta Qty tion C1 10 uF/ 50V PANASONIC_E Panasonic EEE-HA1H100P PCE4209CT-ND (1097.244 2355.906 R90 1 C2 2.2 uF/35V PANASONIC_C Panasonic EEE-FC1V2R2R PCE4027CT-ND (1377.988 1750.504 R270 1 C3 10 nF C0805 Murata Electronics NA GCM2195C1H103JA16D 490-4783-1-ND (437.319 1603.524 R0 16 C4 10 nF C0805 Murata Electronics NA GCM2195C1H103JA16D 490-4783-1-ND (640.445 465.862) R0 6 C5 0.1 uF C0805 Murata Electronics NA GCM21BR72A104KA37L 490-4789-1-ND (1555.177 1790.657) R90 C6 10 nF C0805 Murata Electronics NA GCM2195C1H103JA16D 490-4783-1-ND (3758.815 495.823) R180 C7 10 nF C0805 Murata Electronics NA GCM2195C1H103JA16D 490-4783-1-ND (2922.146 1059.469) R270 C8 10 nF C0805 Murata Electronics NA GCM2195C1H103JA16D 490-4783-1-ND (3536.098 1457.717) R180 C9 10 nF C0805 Murata Electronics NA GCM2195C1H103JA16D 490-4783-1-ND (3548.012 1044.921) R180 C10 10 nF C0805 Murata Electronics NA GCM2195C1H103JA16D 490-4783-1-ND (3407.654 1371.933) R90 C11 0.1 uF C0805 Murata Electronics NA GCM21BR72A104KA37L 490-4789-1-ND (1317.173 2360.283) R270 C12 10 nF C0805 Murata Electronics NA GCM2195C1H103JA16D 490-4783-1-ND (639.197 353.756) R0 C13 10 nF C0805 Murata Electronics NA GCM2195C1H103JA16D 490-4783-1-ND (640.256 555.61) R0 C14 10 nF C0805 Murata Electronics NA GCM2195C1H103JA16D 490-4783-1-ND (641.079 647.634) R0 C15 10 nF C0805 Murata Electronics NA GCM2195C1H103JA16D 490-4783-1-ND (964.902 1242.331) R0 C16 10 nF C0805 Murata Electronics NA GCM2195C1H103JA16D 490-4783-1-ND (965.346 1333.961) R0 C17 10 nF C0805 Murata Electronics NA GCM2195C1H103JA16D 490-4783-1-ND (971.398 1129.232) R0 C18 10 nF C0805 Murata Electronics NA GCM2195C1H103JA16D 490-4783-1-ND (964.386 1424.031) R0 C19 10 nF C0805 Murata Electronics NA GCM2195C1H103JA16D 490-4783-1-ND (962.583 1513.295) R0 C20 .1uF C0805 Murata Electronics NA GCM21BR72A104KA37L 490-4789-1-ND (1096.748 152.161) R180 C22 .1uF C0805 Murata Electronics NA GCM21BR72A104KA37L 490-4789-1-ND (1524.047 162.972) R180 C23 .1uF C0805 Murata Electronics NA GCM21BR72A104KA37L 490-4789-1-ND (1661.445 1263.165) R270 C24 .1uF C0805 Murata Electronics NA GCM21BR72A104KA37L 490-4789-1-ND (2784.752 589.614) R0 C25 10nF C0805 Murata Electronics NA GCM2195C1H103JA16D 490-4783-1-ND (639.492 258.76) R0 Part Name Capacitors KIT33812EKEVBE Evaluation Board, Rev. 2.0 16 Freescale Semiconductor KIT33812EKEVBE Bill of Material Part Name Location Orienta Qty tion Value Package Mfr. Mfr. Part # Digi-Key Part # D1 MBRS360T3 SMC ON Semiconductor MBRS360T3G MBRS360T3GOSCT-ND (684.646 2468.898) R180 1 D2 SMBJ40 DO214AA Little Fuse SMBJ40A SMBJ40ALFCT-ND (673.228 2243.622) R180 1 D4 S1GB-13 DO214AA Diodes, Inc. S1GB-13-F S1GB-FDICT-ND (3366.72 1850.402) R180 3 D5 S1GB-13 DO214AA Diodes, Inc. S1GB-13-F S1GB-FDICT-ND (3320.437 1026.295) R180 D6 S1GB-13 DO214AA Diodes, Inc. S1GB-13-F S1GB-FDICT-ND (3788.433 396.815) R180 D7 SS12 DO214AC Vishay/General SS12-E3/51T Semi. SS12-E3/51TGI-ND (2892.591 1208.165) R0 1 Diodes D8 SMBJ24A DO214AA Little Fuse SMBJ24A SMBJ24ALFCT-ND (2652.594 1075.378) R90 1 +5V_LED Green LED CHIPLED_0805 Panasonic LNJ306G5PRX P11493CT-ND (1548.839 2062.543) R270 12 IGNFLT_LED Green LED CHIPLED_0805 Panasonic LNJ306G5PRX P11493CT-ND (811.244 356.508) R90 IGNITION_LED Green LED CHIPLED_0805 Panasonic LNJ306G5PRX P11493CT-ND (3571.504 1976.976) R180 USB_ON_LED Green LED CHIPLED_0805 Panasonic LNJ306G5PRX P11493CT-ND (232.22 1661.366) R270 INJFLT_LED Green LED CHIPLED_0805 Panasonic LNJ306G5PRX P11493CT-ND (807.516 557.181) R90 INJ_LED Green LED CHIPLED_0805 Panasonic LNJ306G5PRX P11493CT-ND (3566.118 1164.677) R180 RELFLT_LED Green LED CHIPLED_0805 Panasonic LNJ306G5PRX P11493CT-ND (812.126 461.988) R90 LAMP_LED Green LED CHIPLED_0805 Panasonic LNJ306G5PRX P11493CT-ND (3575.409 1571.547) R180 REL_LED Green LED CHIPLED_0805 Panasonic LNJ306G5PRX P11493CT-ND (3560.366 756.697) R180 RESET_LED Green LED CHIPLED_0805 Panasonic LNJ306G5PRX P11493CT-ND (806.331 653.417) R90 MRX_LED Green LED CHIPLED_0805 Panasonic LNJ306G5PRX P11493CT-ND (810.327 258.681) R90 VPWR_LED Green LED CHIPLED_0805 Panasonic LNJ306G5PRX P11493CT-ND (627.709 2114.701) R90 Q1 FZT753SMD SOT223 Zetex, Inc. FZT753TA FZT753CT-ND (1566.016 1517.457) R0 1 Q3 IRGS14C40LP T0263N BF International Rectifier IRGS14C40LPBF IRGS14C40LPBF-ND (2847.083 2282.74) R270 1 Transistors Integrated Circuits U1 MC33812 32SOICEP_FINA Freescale L Semiconductor PCZ33812 N/A (2176.756 1320.075) R0 1 U2 4049D SOP16 Texas Instruments CD4049UBNSR 296-14112-1-ND (1527.165 433.114) R270 1 R1 0 R0805 Panasonic ECG ERJ-6GEY0R00V P0.0ACT-ND (2371.787 1738.146) R270 2 R2 1K M0805 Panasonic ECG ERJ-6GEYJ102V P1.0KACT-ND (3542.252 2125.283) R90 8 R3 1K M0805 Panasonic ECG ERJ-6GEYJ102V P1.0KACT-ND (3556.307 1307.303) R90 R4 1K M0805 Panasonic ECG ERJ-6GEYJ102V P1.0KACT-ND (3562.244 899.949) R90 R5 1K M0805 Panasonic ECG ERJ-6GEYJ102V P1.0KACT-ND (3570.165 1719.039) R90 R6 470 M0805 Panasonic ECG ERJ-6GEYJ471V P470ACT-ND (1092.555 638.331) R0 R7 470 M0805 Panasonic ECG ERJ-6GEYJ471V P470ACT-ND (1094.189 350.961) R0 R8 1K M0805 Panasonic ECG ERJ-6GEYJ102V P1.0KACT-ND (800.634 2114.559) R0 R9 470 M0805 Panasonic ECG ERJ-6GEYJ471V P470ACT-ND (237.594 1825.079) R0 R10 470 M0805 Panasonic ECG ERJ-6GEYJ471V P470ACT-ND (1088.65 542.626) R0 R11 1K M0805 Panasonic ECG ERJ-6GEYJ102V P1.0KACT-ND (2084 2272.008) R0 R12 4.02K R1206 Panasonic ECG ERJ-8ENF4021V P4.02KFCT-ND (2833.26 1838.929) R0 R13 1K M0805 Panasonic ECG ERJ-6GEYJ102V P1.0KACT-ND (2086.646 2392.969) R0 R14 470 M0805 Panasonic ECG ERJ-6GEYJ471V P470ACT-ND (1093.539 260) R0 Resistors 6 2 1 KIT33812EKEVBE Evaluation Board, Rev. 2.0 Freescale Semiconductor 17 KIT33812EKEVBE Bill of Material Part Name Value Package Mfr. Mfr. Part # Digi-Key Part # Location Orienta Qty tion Resistors (Continued) R15 0 R0805 Panasonic ECG ERJ-6GEY0R00V P0.0ACT-ND (2100.657 1733.843) R270 R16 36.0K R2512 Vishay/Dale 541-36KXCT-ND (3073.795 1802.346) R270 R17 1K M0805 Panasonic ECG ERJ-6GEYJ102V P1.0KACT-ND (2827.925 1061.657) R270 R18 470 M0805 Panasonic ECG ERJ-6GEYJ471V P470ACT-ND (1544.917 1978.461) R180 R19 4.7K M0805 Panasonic ECG ERJ-6GEYJ472V P4.7KACT-ND (1090 740) R0 R20 470 M0805 Panasonic ECG ERJ-6GEYJ471V P470ACT-ND (1094.98 448.803) R0 R21 4.7K M0805 Panasonic ECG ERJ-6GEYJ472V P4.7KACT-ND (1849.992 1745.831) R180 CRCW251236K0JNEG 1 Headers & Jumpers OUTPUTS MA06-1 MA06-1 Tyco Electronics 87224-6 Amp A26551-ND (496.043 403.72) R90 1 LIN_PWR MA02-1 MA02-1 Tyco Electronics 87224-2 Amp A26543-ND (2885.441 771.134) R270 2 TEST1 MA01-1 MA01-1 Tyco Electronics 87224-1 Amp A26541-ND (2367.618 1943.13) R0 6 TEST2 MA01-1 MA01-1 Tyco Electronics 87224-1 Amp A26541-ND (2093.524 1937.445) R0 TEST3 MA01-1 MA01-1 Tyco Electronics 87224-1 Amp A26541-ND (2617.248 1943.228) R180 GND MA01-1 MA01-1 Tyco Electronics 87224-1 Amp A26541-ND (486.169 2024.677) R0 USB_SPI_DONGL MA08-2 E MA08-2 Tyco Electronics 9-146261-0-04 Amp A34268-04-ND (230.394 1179.28) R90 VCC MA01-1 MA01-1 Tyco Electronics 87224-1 Amp A26541-ND (1186.402 1599.343) R180 VPWR MA01-1 MA01-1 Tyco Electronics 87224-1 Amp A26541-ND (952.776 2105.823) R180 IGNSUP MA03-1 MA03-1 Tyco Electronics 87224-3 Amp A26545-ND (1849.13 1509.134) R90 WDRFSH MA02-1 MA02-1 Tyco Electronics 87224-2 Amp A26543-ND (2188.618 977.976) R180 WD_INH MA03-1 MA03-1 Tyco Electronics 87224-3 Amp A26545-ND (2631.469 1574.665) R0 IGNITION OUT X2 AK500/2 Phoenix Contact 1729128 277-1247-ND (3781.425 1963.713) R90 LAMP OUT X4 AK500/2 Phoenix Contact 1729128 277-1247-ND (3783.579 1563.244) R90 INJECTOR OUT X5 AK500/2 Phoenix Contact 1729128 277-1247-ND (3786.181 1163.307) R90 RELAY OUT X6 AK500/2 Phoenix Contact 1729128 277-1247-ND (3788.016 761.063) R90 VBAT AK500/2 Phoenix Contact 1729128 277-1247-ND (170.945 2167.244) R270 Molex Waldom Elec. WM3901-ND (3189.016 677.563) R0 1 2 Connectors VBAT ISO9141 44068ANGLE 5566-4A 39-29-1048 5 1 Notes: Freescale does not assume liability, endorse, or warrant components from external manufacturers that are referenced in circuit drawings or tables. While Freescale offers component recommendations in this configuration, it is the customer's responsibility to validate their application. KIT33812EKEVBE Evaluation Board, Rev. 2.0 18 Freescale Semiconductor References 10 References Following are URLs where you can obtain information on other Freescale products and application solutions: Products Links Data Sheet MC33812 www.freescale.com/files/analog/doc/data_sheet/MC33812.pdf Freescale's Web Site www.freescale.com Freescale's Analog Web Site www.freescale.com/analog Freescale's Powertrain an Engine Control www.freescale.com/powertrain_and_engine_control Freescale's Automotive Applications www.freescale.com/automotive KIT33812EKEVBE Evaluation Board, Rev. 2.0 Freescale Semiconductor 19 Revision History 11 Revision History REVISION 2.0 DATE 7/2009 DESCRIPTION OF CHANGES * Initial Release KIT33812EKEVBE Evaluation Board, Rev. 2.0 20 Freescale Semiconductor How to Reach Us: Home Page: www.freescale.com Web Support: http://www.freescale.com/support USA/Europe or Locations Not Listed: Freescale Semiconductor, Inc. Technical Information Center, EL516 2100 East Elliot Road Tempe, Arizona 85284 1-800-521-6274 or +1-480-768-2130 www.freescale.com/support Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) www.freescale.com/support Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor China Ltd. Exchange Building 23F No. 118 Jianguo Road Chaoyang District Beijing 100022 China +86 10 5879 8000 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 or +1-303-675-2140 Fax: +1-303-675-2150 LDCForFreescaleSemiconductor@hibbertgroup.com Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals", must be validated for each customer application by customer's technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. FreescaleTM and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. (c) Freescale Semiconductor, Inc. 2009. All rights reserved. KT33812UG Rev. 2.0 7/2009