RoHS Compliant Serial ATA Flash Drive SAFD18S4 Product Specifications December 2nd, 2011 Version 1.0 Apacer Technology Inc. Apacer Technology Inc. 9/F, No. 100, Hsin Tai Wu Rd., Hsichih, Taipei Hsien 221, Taiwan 4th Fl., 75 Hsin Tai Wu Rd., Sec.1, Hsichih, New Taipei City, Taiwan 221 Tel: +886-2-2696-1666 Fax: +886-2-2696-1668 Tel: +886-2-2698-2888 Fax: +886-2-2698-2889 www.apacer.com www.apacer.com Serial ATA Flash Drive APS1845xxxx-AXX Features: z Standard Serial ATA 2.6 (Gen. 2) - Serial ATA 2.6 (Gen. 2) - SATA, 3.0 Gbps - ATA-compatible command set z Capacities - 4, 8, 16, 32, 64 GB z Performance* - Burst read/write: 300 MB/sec - Sustained read: up to 165 MB/sec - Sustained write: up to 150 MB/sec z z Intelligent endurance design - Built-in hardware ECC, enabling up to 16/24 bit correction per 1K bytes - Static wear-leveling scheme together with dynamical block allocation to significantly increase the lifetime of a flash device and optimize the disk performance - Flash bad-block management - S.M.A.R.T. - Power Failure Management - ATA Secure Erase - TRIM NAND Flash Type: SLC z Data integrity under power-cycling - No battery required for data storage z Temperature ranges - Operation: 0C to 70C (32 ~ 158F) - Extended: -40C to 85C (-40 ~ 185F) - Storage: -40C to 100C (-40 ~ 212F) z Supply voltage - 5.0 V 5% z Power consumption (typical)* - Active mode: 333 mA - Idle mode: 95 mA z Form factor - JEDEC MO-297 - Only 4mm in thickness - Dimensions (54 x 39.8 x 4, unit: mm) z Connector - 7-pin SATA signal connector - 15-pin SATA power connector z Shock & Vibration - Shock: 50g (approx.) - Vibration: 15g (approx.) z RoHS compliant *Varies from capacities. The values addressed here are typical and may vary depending on settings and platforms. 1 (c) 2011 Apacer Technology Inc. Rev. 1.0 Serial ATA Flash Drive APS1845xxxx-AXX Table of Contents 1. Product Description ................................................................................................. 3 1.1 Introduction .................................................................................................................................................3 1.2 Functional Block Diagram..........................................................................................................................3 1.3 ATA Mode Support ....................................................................................................................................4 1.4 Capacity Specification.................................................................................................................................4 1.5 Performance.................................................................................................................................................4 1.6 Pin Assignments ..........................................................................................................................................5 2. Software Interface .................................................................................................... 7 2.1 Command Set ..............................................................................................................................................7 3. Flash Management ................................................................................................... 8 3.1 Error Correction/Detection ........................................................................................................................8 3.2 Bad Block Management..............................................................................................................................8 3.3 Wear Leveling..............................................................................................................................................8 3.4 Power Failure Management .......................................................................................................................8 3.5 ATA Secure Erase .......................................................................................................................................8 3.6 S.M.A.R.T. ...................................................................................................................................................9 3.7 TRIM............................................................................................................................................................9 4. Environmental Specifications ............................................................................... 10 4.1 Environments.............................................................................................................................................10 4.2 Mean Time Between Failures (MTBF)....................................................................................................10 4.3 Certification and Compliance ..................................................................................................................10 5. Electrical Characteristics ...................................................................................... 11 5.1 Operating Voltage .....................................................................................................................................11 5.2 Power Consumption..................................................................................................................................11 5.3 Electrostatic Discharge .............................................................................................................................11 5.4 Electrical Fast Transient/Burst................................................................................................................12 6. Physical Characteristics........................................................................................ 13 7. Product Ordering Information ............................................................................... 15 7.1 Product Code Designations ......................................................................................................................15 7.2 Valid Combinations ..................................................................................................................................16 2 (c) 2011 Apacer Technology Inc. Rev. 1.0 Serial ATA Flash Drive APS1845xxxx-AXX 1. Product Description 1.1 Introduction Apacer's SAFD18S4 is a solid-state disk (SSD) drive that contains a controller, embedded firmware, and flash media along with a male connector. Using NAND flash memory devices, the SAFD drive interfaces with the host allowing data to be seamlessly transferred between the host and the flash devices. SAFD18S4 drive is designed with a single-chip controller, offering capacities of up to 64 gigabytes and providing full support for the SATA high-speed interface standard. It can operate at sustained access rates of up to 100 megabytes per second, which is much faster than any other solid-state or traditional SATA drive currently available on the market. In addition to buffer management through dynamical allocation, SAFD18S4 adopts the Apacer-specific global wear-leveling scheme to allow uniform use of all storage blocks, ensuring that the lifetime of a flash media can be significantly increased and the disk performance is optimized as well. SAFD18S4 provides the S.M.A.R.T. feature that follows the SATA Rev. 2.6, ATA/ATAPI-7 specifications and uses the standard SMART command B0h to read data from the drive. This feature protects the user from unscheduled downtime by monitoring and storing critical drive performance. 1.2 Functional Block Diagram SAFD18S4 drive includes a single-chip SATA Controller and the flash media, as well as the SATA standard interface. The controller integrates the flash management unit with the controller itself to support multi-channel, multi-bank flash arrays. Figure 1-1 shows the functional block diagram. Figure 1-1 Apacer SAFD18S4 block diagram 3 (c) 2011 Apacer Technology Inc. Rev. 1.0 Serial ATA Flash Drive APS1845xxxx-AXX 1.3 ATA Mode Support SAFD18S4 provides ATA mode support as follows: z z z 1.4 Up to PIO mode-4 Up to Multiword DMA mode-2 Up to UDMA mode-5 Capacity Specification Capacity specification of SAFD18S4 product family is available as shown in Table 1-1. It lists the specific capacity, the default numbers of logical cylinders and heads, and the number of logical sectors per track for each product line. Table 1-1 Capacity specification Capacity Total Bytes* Cylinders Heads Sectors Max LBA* 4 GB 3,011,420,160 5,835 16 63 5,881,680 8 GB 7,012,196,352 15,334 16 63 13,695,696 16 GB 16,013,942,784 16,383 16 63 31,277,232 32 GB 32,017,047,552 16,383 16 63 62,533,296 64 GB 64,023,257,088 16,383 16 63 125,045,424 *Display of total bytes varies from file systems. **Cylinders, heads or sectors are not applicable for these capacities. Only LBA addressing applies. 1.5 Performance Performance of SAFD18S4 is shown in Table 1-2. Table 1-2 Performance specification Capacity Performance Sustained Read (MB/s) Sustained Write (MB/s) 4 GB 8 GB 16 GB 32 GB 64 GB 150 160 160 160 165 50 95 95 145 150 Note: Performance varies from flash configurations. 4 (c) 2011 Apacer Technology Inc. Rev. 1.0 Serial ATA Flash Drive APS1845xxxx-AXX 1.6 Pin Assignments Table 1-3 describes the SAFD signal segment, and Table1-4, power segment. Figure 1-2 SATA Connectors Table 1-3: Signal segment Name Type S1 GND S2 RxP + Differential Receive Signal S3 RxN - Differential Receive Signal S4 GND S5 TxN S6 TxP S7 GND Table 1-4: Power segment Description Pin Signal/Description P1 Unused (3.3V) P2 Unused (3.3V) P3 Unused (3.3V) P4 Ground - Differential Transmit Signal P5 Ground + Differential Transmit Signal P6 Ground P7 5V P8 5V P9 5V P10 Ground P11 Reserved/Ground P12 Ground P13 Unused (12V) P14 Unused (12V) P15 Unused (12V) 5 (c) 2011 Apacer Technology Inc. Rev. 1.0 Serial ATA Flash Drive APS1845xxxx-AXX Figure 1-3 SATA Cable/Connector Connection Diagram The connector on the left represents the Host with TX/RX differential pairs connected to a cable. The connector on the right shows the Device with TX/RX differential pairs also connected to the cable. Notice also the ground path connecting the shielding of the cable to the Cable Receptacle. 6 (c) 2011 Apacer Technology Inc. Rev. 1.0 Serial ATA Flash Drive APS1845xxxx-AXX 2. Software Interface 2.1 Command Set Table 2-1 summarizes the ATA commands supported by SAFD18S4. Table 2-1: Command set Code Command Code Command E5h Check Power Mode F3h Security Erase Prepare 06h Data Set Management F4h Security Erase Unit 90h Execute Device Diagnostic F5h Security Freeze Lock E7h Flush Cache F1h Security Set Password EAh Flush Cache EXT F2h Security Unlock Ech Identify Device 70h Seek E3h Idle Efh Set Features E1h Idle Immediate C6h Set Multiple Mode 91h Initialize Device Parameters E6h Sleep C8h Read DMA B0h SMART 25h Read DMA EXT E2h Standby C4h Read Multiple E0h Standby Immediate 29h Read Multiple EXT Cah Write DMA 20h Read Sector 35h Write DMA EXT 24h Read Sector EXT C5h Write Multiple 40h Read Verify Sectors 39h Write Multiple EXT 42h Read Verify Sectors EXT 30h Write Sector 10h Recalibrate 34h Write Sector EXT F6h Security Disable Password 7 (c) 2011 Apacer Technology Inc. Rev. 1.0 Serial ATA Flash Drive APS1845xxxx-AXX 3. Flash Management 3.1 Error Correction/Detection SAFD18S4 implements a hardware ECC scheme, based on the BCH algorithm. It can detect and correct up to 16 bits or 24 bits error in 1K bytes. 3.2 Bad Block Management Although bad blocks on the flash media are already identified by the flash manufacturer, they can also be accumulated over time during operation. SAFD18S4's controller maintains a table that lists those normal blocks with disk data, the free blocks for wear leveling, and bad blocks with errors. When a normal block is detected broken, it is replaced with a free block and listed as a bad block. When a free block is detected broken, it is then removed from the free block list and marked as a bad block. During device operation, this ensures that newly accumulated bad blocks are transparent to the host. The device will stop file write service once there are only two free blocks left such that the read function is still available for copying the files from the disk into another. 3.3 Wear Leveling The NAND flash devices are limited by a certain number of write cycles. When using a FAT-based file system, frequent FAT table updates are required. If some area on the flash wears out faster than others, it would significantly reduce the lifetime of the whole SSD, even if the erase counts of others are far from the write cycle limit. Thus, if the write cycles can be distributed evenly across the media, the lifetime of the media can be prolonged significantly. This scheme is called wear leveling. Apacer's wear-leveling scheme is achieved both via buffer management and Apacer-specific static wear leveling. They both ensure that the lifetime of the flash media can be increased, and the disk access performance is optimized as well. 3.4 Power Failure Management The Low Power Detection on the controller initiates crucial data saving before the power supplied to the device is too low. This feature prevents the device from crash and ensures data integrity during an unexpected power-off. 3.5 ATA Secure Erase Accomplished by the Secure Erase (SE) command, which added to the open ANSI standards that control disk drives, "ATA Secure Erase" is built into the disk drive itself and thus far less susceptible to malicious software attacks than external software utilities. It is a positive easy-to-use data destroy command, amounting to electronic data shredding. Executing the command causes a drive to internally completely erase all possible user data. This command is carried out within disk drives, so no additional software is required. Once executed, neither data nor the erase counter on the device would be recoverable, which blurs the accuracy of device lifespan. The process to erase will not be stopped until finished while encountering power failure, and will be continued when power is back on. 8 (c) 2011 Apacer Technology Inc. Rev. 1.0 Serial ATA Flash Drive APS1845xxxx-AXX 3.6 S.M.A.R.T. S.M.A.R.T. is an acronym for Self-Monitoring, Analysis and Reporting Technology, an open standard allowing disk drives to automatically monitor their own health and report potential problems. It protects the user from unscheduled downtime by monitoring and storing critical drive performance and calibration parameters. Ideally, this should allow taking proactive actions to prevent impending drive failure. Apacer SAFD18S4 uses the standard SMART command B0h to read data from the drive for SMART feature as the SATA Rev.2.6 ATA/ATAPI-7 specifications. Based on the SFF-8035i Rev. 2.0 specifications, Apacer SMART defines vendor-specified SMART Attribute IDs (A0h, A1h, A2h, A3h, A4h-A5h) in SAFD18S4. They represent initial back block count, bad block count, spare block count, maximum erase count, and average erase counts respectively. When the Apacer SMART Utility running on the host, it analyzes and reports the disk status to the host before SAFD18S4 is in critical condition. 3.7 TRIM Made of millions of NAND flash cells, SSD can be written into groups called pages in 4K size generally, but can only be erased in larger groups called blocks of 128 pages or 512KB. These stipulations are partially the source of many performance issues. Until an address gets used again, the SSD has to keep track of every last bit of data that's written on it. The ATA-TRIM instruction tilts the balance in favor of the SSD. TRIM addresses a major part of the performance degradation issue over time that plagues all SSDs. A TRIM enabled drive running an OS with TRIM support will stay closer to its peak performance over time. 9 (c) 2011 Apacer Technology Inc. Rev. 1.0 Serial ATA Flash Drive APS1845xxxx-AXX 4. Environmental Specifications 4.1 Environments SAFD18S4 environmental specifications follow the US Military Standard MIL-STD-810F, as shown in below table. Table 4-1 SAFD18S4 environmental specifications Environment Temperature Specification 0C to 70C (Operating), -40C to 85C (operating-extended) -40C to 100C (Non-operating) Humidity Vibration 5% to 95% RH (Non-condensing) Sine wave : 15(G), 10~2000(Hz), Random : 7.7(Grms), 20~2000(Hz) Shock - Operating 4.2 Acceleration: 1,500 G, 0.5 ms Peak acceleration: 50 G, 11 ms Mean Time Between Failures (MTBF) Mean Time Between Failures (MTBF) is predicted based on reliability data for the individual components in SAFD drive. Although many component of MTBF are given in databases and often these values are not really accurate, the prediction result for the SAFD18S4 is more than 2,000,000 hours. Notes about the MTBF: The MTBF is predicated and calculated based on "Telcordia Technologies Special Report, SR-332, Issue 2" method. 4.3 Certification and Compliance SAFD18S4 complies with the following standards: z z z z z z CE - EN55022/55024 FCC 47CFR Part15 Class B RoHS MIL-STD-810F SATA II (SATA Rev. 2.6) Up to ATA/ATAPI-7 ( including S.M.A.R.T.) 10 (c) 2011 Apacer Technology Inc. Rev. 1.0 Serial ATA Flash Drive APS1845xxxx-AXX 5. Electrical Characteristics 5.1 Operating Voltage Table 5-1 lists the supply voltage for SAFD18S4. Table 5-1 SAFD18S4 operating voltage Parameter Conditions Supply voltage 5.2 5V 5% ( 4.75-5.25 V) Power Consumption Table 5-2 Power consumption (typical) Capacity Mode Active (mA) Stand By (mA) 4 GB 8 GB 16 GB 32 GB 64 GB 255 333 333 280 300 85 95 95 77 80 Note: Power consumptions may vary depending on settings and platforms 5.3 Electrostatic Discharge Electrostatic discharge Item Amount of Voltage Discharge Required Criteria Complied To Criteria (A,B,C) 10 +8kV B A 10 -8kV B A 25 +4kV B A 25 -4kV B A Indirect Discharge (HCP) 25 +4kV B A 25 -4kV B A Indirect Discharge (VCP Front) 25 +4kV B A 25 -4kV B A Indirect Discharge (VCP Left) 25 +4kV B A 25 -4kV B A Air Discharge Contact Discharge 11 (c) 2011 Apacer Technology Inc. Rev. 1.0 Serial ATA Flash Drive APS1845xxxx-AXX 5.4 Indirect Discharge (VCP Back) 25 +4kV B A 25 -4kV B A Indirect Discharge (VCP Right) 25 +4kV B A 25 -4kV B A Electrical Fast Transient/Burst Electrical Fast Transient/Burst Inject Line L-N-PE Polarity Voltage kV Inject Time (Second) 1kV 60 Inject Method Required Criteria Direct Complied to Criteria B A Notes about 5.3 Electrostatic Discharge & 5.4 Electrical Fast Transient/Burst The tests performed are from lowest level up to the highest level as required by standard, but only highest level is shown on the report. Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information: EUT stopped operation and could / could not be reset by operator at kV. No false alarms or other malfunctions were observed during or after the test. The Contact discharges were applied at least total 200 discharges at a minimum of four test points. 12 (c) 2011 Apacer Technology Inc. Rev. 1.0 Serial ATA Flash Drive APS1845xxxx-AXX 6. Physical Characteristics Unit: Tolerance: 0.2 13 (c) 2011 Apacer Technology Inc. Rev. 1.0 Serial ATA Flash Drive APS1845xxxx-AXX Unit: Tolerance: 0.2 14 (c) 2011 Apacer Technology Inc. Rev. 1.0 Serial ATA Flash Drive APS1845xxxx-AXX 7. Product Ordering Information 7.1 Product Code Designations A P S 184 5 x x x x - A X X Temperature Range Blank: Standard W: Extended Temperature Flash type T: Toshiba C: Micron Version Control Capacities: 004G = 008G = 016G = 032G = 064G = 4GB 8GB 16GB 32GB 64GB Solution version MO-297 Form Factor Serial ATA Flash Drive Apacer Product Code 15 (c) 2011 Apacer Technology Inc. Rev. 1.0 Serial ATA Flash Drive APS1845xxxx-AXX 7.2 Valid Combinations Capacity 4GB 8GB 16GB 32GB 64GB Standard Extended Temperature APS1845004G-AT APS1845008G-AT APS1845016G-AT APS1845032G-AC APS1845064G-AC APS1845004G-ATW APS1845008G-ATW APS1845016G-ATW APS1845032G-ACW APS1845064G-ACW Note: Valid combinations are those products in mass production or will be in mass production. Consult your Apacer sales representative to confirm availability of valid combinations and to determine availability of new combinations. 16 (c) 2011 Apacer Technology Inc. Rev. 1.0 Serial ATA Flash Drive APS1845xxxx-AXX Revision History Revision Description Date 0.1 Preliminary release 11/17/2011 1.0 Official release 12/02/2011 17 (c) 2011 Apacer Technology Inc. Rev. 1.0 Serial ATA Flash Drive APS1845xxxx-AXX Global Presence Taiwan (Headquarters) Apacer Technology Inc. th 4 Fl., 75 Hsin Tai Wu Rd., Sec.1 Hsichih, New Taipei City Taiwan 221 R.O.C. Tel: +886-2-2698-2888 Fax: +886-2-2698-2889 amtsales@apacer.com U.S.A. Apacer Memory America, Inc. 386 Fairview Way, Suite102, Milpitas, CA 95035 Tel: 1-408-518-8699 Fax: 1-408-935-9611 sa@apacerus.com Japan Apacer Technology Corp. 5F, Matsura Bldg., Shiba, Minato-Ku Tokyo, 105-0014, Japan Tel: 81-3-5419-2668 Fax: 81-3-5419-0018 jpservices@apacer.com Europe Apacer Technology B.V. Science Park Eindhoven 5051 5692 EB Son, The Netherlands Tel: 31-40-267-0000 Fax: 31-40-267-0000#6199 sales@apacer.nl China Apacer Electronic (Shanghai) Co., Ltd 1301, No.251,Xiaomuqiao Road, Shanghai, 200032, China Tel: 86-21-5529-0222 Fax: 86-21-5206-6939 sales@apacer.com.cn India Apacer Technologies Pvt Ltd, #1064, 1st Floor, 7th `A' Main, 3rd Block Koramangala, Bangalore - 560 034 Tel: +91 80 4152 9061/62/63 Fax: +91 80 4170 0215 sales_india@apacer.com 18 (c) 2011 Apacer Technology Inc. Rev. 1.0 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Apacer: APS1845016G-ATW