4-Channel, 1 MSPS, 8-/10-/12-Bit ADCs with Sequencer in 16-Lead TSSOP AD7904/AD7914/AD7924 FEATURES FUNCTIONAL BLOCK DIAGRAM AVDD REFIN VIN0 T/H 8-/10-/12-BIT SUCCESSIVE APPROXIMATION ADC VIN1 I/P MUX VIN2 VIN3 SCLK SEQUENCER CONTROL LOGIC DOUT DIN CS AD7904/AD7914/AD7924 VDRIVE AGND 03087-001 Fast throughput rate: 1 MSPS Specified for AVDD of 2.7 V to 5.25 V Low power: 6 mW maximum at 1 MSPS with 3 V supplies 13.5 mW maximum at 1 MSPS with 5 V supplies 4 single-ended inputs with sequencer Wide input bandwidth AD7924, 70 dB SNR at 50 kHz input frequency Flexible power/serial clock speed management No pipeline delays High speed serial interface: SPI/QSPITM/ MICROWIRETM/DSP compatible Shutdown mode: 0.5 A maximum 16-lead TSSOP package Qualified for automotive applications Figure 1. GENERAL DESCRIPTION PRODUCT HIGHLIGHTS The AD7904/AD7914/AD7924 are, respectively, 8-bit, 10-bit, and 12-bit, high speed, low power, 4-channel successive approximation ADCs. The parts operate from a single 2.7 V to 5.25 V power supply and feature throughput rates up to 1 MSPS. The parts contain a low noise, wide bandwidth track-and-hold amplifier that can handle input frequencies in excess of 8 MHz. 1. The conversion process and data acquisition are controlled using CS and the serial clock signal, allowing the device to easily interface with microprocessors or DSPs. The input signal is sampled on the falling edge of CS and conversion is initiated at this point. There are no pipeline delays associated with the part. The AD7904/AD7914/AD7924 use advanced design techniques to achieve very low power dissipation at maximum throughput rates. At maximum throughput rates, the AD7904/AD7914/ AD7924 consume 2 mA maximum with 3 V supplies; with 5 V supplies, the current consumption is 2.7 mA maximum. Through the configuration of the control register, the analog input range for the part can be selected as 0 V to REFIN or 0 V to 2 x REFIN, with either straight binary or twos complement output coding. The AD7904/AD7914/AD7924 each feature four singleended analog inputs with a channel sequencer to allow a preprogrammed selection of channels to be converted sequentially. The conversion time for the AD7904/AD7914/AD7924 is determined by the SCLK frequency, which is also used as the master clock to control the conversion. 2. 3. 4. 5. High Throughput with Low Power Consumption. The AD7904/AD7914/AD7924 offer throughput rates up to 1 MSPS. At the maximum throughput rate with 3 V supplies, the AD7904/AD7914/AD7924 dissipate only 6 mW of power maximum. Four Single-Ended Inputs with Channel Sequencer. A consecutive sequence of channels can be selected, through which the ADC will cycle and convert on. Single-Supply Operation with VDRIVE Function. The AD7904/AD7914/AD7924 operate from a single 2.7 V to 5.25 V supply. The VDRIVE function allows the serial interface to connect directly to 3 V or 5 V processor systems, independent of VDD. Flexible Power/Serial Clock Speed Management. The conversion rate is determined by the serial clock, allowing the conversion time to be reduced by increasing the serial clock speed. The parts also feature two shutdown modes to maximize power efficiency at lower throughput rates. Current consumption is 0.5 A maximum when in full shutdown. No Pipeline Delay. The parts feature a standard successive approximation ADC with accurate control of the sampling instant via the CS input and once-off conversion control. Rev. B Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c)2002-2011 Analog Devices, Inc. All rights reserved. AD7904/AD7914/AD7924 TABLE OF CONTENTS Features .............................................................................................. 1 Converter Operation.................................................................. 18 Functional Block Diagram .............................................................. 1 ADC Transfer Function............................................................. 19 General Description ......................................................................... 1 Typical Connection Diagram ................................................... 20 Product Highlights ........................................................................... 1 Modes of Operation ....................................................................... 22 Revision History ............................................................................... 2 Normal Mode (PM1 = PM0 = 1) ............................................. 22 Specifications..................................................................................... 3 Full Shutdown Mode (PM1 = 1, PM0 = 0) ............................. 22 AD7904 Specifications................................................................. 3 Auto Shutdown Mode (PM1 = 0, PM0 = 1) ........................... 22 AD7914 Specifications................................................................. 5 Powering Up the AD7904/AD7914/AD7924 ......................... 23 AD7924 Specifications................................................................. 7 Power vs. Throughput Rate........................................................... 25 Timing Specifications .................................................................. 9 Serial Interface ............................................................................ 25 Absolute Maximum Ratings.......................................................... 10 Applications Information .............................................................. 27 ESD Caution................................................................................ 10 Microprocessor Interfacing....................................................... 27 Pin Configuration and Function Descriptions........................... 11 Grounding and Layout .............................................................. 28 Typical Performance Characteristics ........................................... 12 Evaluating AD7904/AD7914/AD7924 Performance ............ 29 Terminology .................................................................................... 14 Outline Dimensions ....................................................................... 30 Control Register.............................................................................. 15 Ordering Guide .......................................................................... 30 Sequencer Operation ................................................................. 16 Automotive Products ................................................................. 30 Circuit Information ........................................................................ 18 REVISION HISTORY 7/11--Rev. A to Rev. B Changes to Features Section............................................................ 1 Changes to Signal to (Noise + Distortion) (SINAD) Parameter and Signal-to-Noise Ratio (SNR) Parameter in Table 1 .............. 3 Changes to Signal to (Noise + Distortion) (SINAD) Parameter and Signal-to-Noise Ratio (SNR) Parameter in Table 2 .............. 5 Changes to Signal to (Noise + Distortion) (SINAD) Parameter and Signal-to-Noise Ratio (SNR) Parameter in Table 3 .............. 7 Changes to Table 5.......................................................................... 10 Changes to Ordering Guide .......................................................... 30 Added Automotive Products Section .......................................... 30 2/09--Rev. 0 to Rev. A Updated Format..................................................................Universal Moved Figure 2 ..................................................................................9 Change to Table 5 ........................................................................... 10 Changes to Typical Performance Characteristics Section ........ 12 Moved Terminology Section......................................................... 14 Updated Outline Dimensions....................................................... 30 Changes to Ordering Guide .......................................................... 30 11/02--Revision 0: Initial Version Rev. B | Page 2 of 32 AD7904/AD7914/AD7924 SPECIFICATIONS AD7904 SPECIFICATIONS AVDD = VDRIVE = 2.7 V to 5.25 V, REFIN = 2.5 V, fSCLK = 20 MHz, TA = TMIN to TMAX, unless otherwise noted. Table 1. Parameter DYNAMIC PERFORMANCE Signal to (Noise + Distortion) (SINAD) 2 Signal-to-Noise Ratio (SNR) Total Harmonic Distortion (THD)2 Peak Harmonic or Spurious Noise (SFDR) Intermodulation Distortion (IMD) Second-Order Terms Third-Order Terms Aperture Delay Aperture Jitter Channel-to-Channel Isolation2 Full Power Bandwidth DC ACCURACY Resolution Integral Nonlinearity (INL)2 Differential Nonlinearity (DNL)2 0 V to REFIN Input Range Offset Error2 Offset Error Match2 Gain Error2 Gain Error Match2 0 V to 2 x REFIN Input Range Positive Gain Error2 Positive Gain Error Match2 Zero Code Error2 Zero Code Error Match2 Negative Gain Error2 Negative Gain Error Match2 ANALOG INPUT Input Voltage Range DC Leakage Current Input Capacitance REFERENCE INPUT REFIN Input Voltage DC Leakage Current REFIN Input Impedance LOGIC INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Current, IIN Input Capacitance, CIN 3 B Version 1 Unit 49 48.5 49 48.5 -66 -64 dB min dB min dB min dB min dB max dB max -90 -90 10 50 -85 8.2 1.6 dB typ dB typ ns typ ps typ dB typ MHz typ MHz typ 8 0.2 0.2 Bits LSB max LSB max 0.5 0.05 0.2 0.05 LSB max LSB max LSB max LSB max Test Conditions/Comments fIN = 50 kHz sine wave, fSCLK = 20 MHz B models W models B models W models fa = 40.1 kHz, fb = 41.5 kHz fIN = 400 kHz @ 3 dB @ 0.1 dB Guaranteed no missed codes to 8 bits Straight binary output coding -REFIN to +REFIN biased about REFIN with twos complement output coding 0.2 0.05 0.5 0.1 0.2 0.05 LSB max LSB max LSB max LSB max LSB max LSB max 0 to REFIN 0 to 2 x REFIN 1 20 V V A max pF typ RANGE bit set to 1 RANGE bit set to 0, AVDD/VDRIVE = 4.75 V to 5.25 V 2.5 1 36 V A max k typ 1% specified performance 0.7 x VDRIVE 0.3 x VDRIVE 1 10 V min V max A max pF max Rev. B | Page 3 of 32 fSAMPLE = 1 MSPS Typically 10 nA, VIN = 0 V or VDRIVE AD7904/AD7914/AD7924 Parameter LOGIC OUTPUTS Output High Voltage, VOH Output Low Voltage, VOL Floating-State Leakage Current Floating-State Output Capacitance3 Output Coding CONVERSION RATE Conversion Time Track-and-Hold Acquisition Time2 Throughput Rate POWER REQUIREMENTS VDD VDRIVE IDD 4 Normal Mode (Static) Normal Mode (Operational) Auto Shutdown Mode Full Shutdown Mode Power Dissipation4 Normal Mode (Operational) Auto Shutdown Mode (Static) Full Shutdown Mode B Version 1 Unit Test Conditions/Comments VDRIVE - 0.2 V min 0.4 V max 1 A max 10 pF max Straight (natural) binary Twos complement ISOURCE = 200 A, AVDD = 2.7 V to 5.25 V ISINK = 200 A 800 300 300 1 ns max ns max ns max MSPS max 16 SCLK cycles with SCLK at 20 MHz Sine wave input Full-scale step input See the Serial Interface section 2.7/5.25 2.7/5.25 V min/V max V min/V max 600 2.7 2 960 0.5 0.5 A typ mA max mA max A typ A max A max Digital inputs = 0 V or VDRIVE AVDD = 2.7 V to 5.25 V, SCLK on or off AVDD = 4.75 V to 5.25 V, fSCLK = 20 MHz AVDD = 2.7 V to 3.6 V, fSCLK = 20 MHz fSAMPLE = 250 kSPS Static SCLK on or off (20 nA typ) 13.5 6 2.5 1.5 2.5 1.5 mW max mW max W max W max W max W max AVDD = 5 V, fSCLK = 20 MHz AVDD = 3 V, fSCLK = 20 MHz AVDD = 5 V AVDD = 3 V AVDD = 5 V AVDD = 3 V 1 Temperature range for B versions: -40C to +85C. See the Terminology section. 3 Sample tested @ 25C to ensure compliance. 4 See the Power vs. Throughput Rate section. 2 Rev. B | Page 4 of 32 CODING bit set to 1 CODING bit set to 0 AD7904/AD7914/AD7924 AD7914 SPECIFICATIONS AVDD = VDRIVE = 2.7 V to 5.25 V, REFIN = 2.5 V, fSCLK = 20 MHz, TA = TMIN to TMAX, unless otherwise noted. Table 2. Parameter DYNAMIC PERFORMANCE Signal to (Noise + Distortion) (SINAD) 2 Signal-to-Noise Ratio (SNR) Total Harmonic Distortion (THD)2 Peak Harmonic or Spurious Noise (SFDR) Intermodulation Distortion (IMD) Second-Order Terms Third-Order Terms Aperture Delay Aperture Jitter Channel-to-Channel Isolation2 Full Power Bandwidth DC ACCURACY Resolution Integral Nonlinearity (INL)2 Differential Nonlinearity (DNL)2 0 V to REFIN Input Range Offset Error2 Offset Error Match2 Gain Error2 Gain Error Match2 0 V to 2 x REFIN Input Range Positive Gain Error2 Positive Gain Error Match2 Zero Code Error2 Zero Code Error Match2 Negative Gain Error2 Negative Gain Error Match2 ANALOG INPUT Input Voltage Range DC Leakage Current Input Capacitance REFERENCE INPUT REFIN Input Voltage DC Leakage Current REFIN Input Impedance LOGIC INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Current, IIN Input Capacitance, CIN 3 B Version 1 Unit 61 60.5 61 60.5 -72 -74 dB min dB min dB min dB min dB max dB max -90 -90 10 50 -85 8.2 1.6 dB typ dB typ ns typ ps typ dB typ MHz typ MHz typ 10 0.5 0.5 Bits LSB max LSB max 2 0.2 0.5 0.2 LSB max LSB max LSB max LSB max Test Conditions/Comments fIN = 50 kHz sine wave, fSCLK = 20 MHz B models W models B models W models fa = 40.1 kHz, fb = 41.5 kHz fIN = 400 kHz @ 3 dB @ 0.1 dB Guaranteed no missed codes to 10 bits Straight binary output coding -REFIN to +REFIN biased about REFIN with twos complement output coding 0.5 0.2 2 0.2 0.5 0.2 LSB max LSB max LSB max LSB max LSB max LSB max 0 to REFIN 0 to 2 x REFIN 1 20 V V A max pF typ RANGE bit set to 1 RANGE bit set to 0, AVDD/VDRIVE = 4.75 V to 5.25 V 2.5 1 36 V A max k typ 1% specified performance 0.7 x VDRIVE 0.3 x VDRIVE 1 10 V min V max A max pF max Rev. B | Page 5 of 32 fSAMPLE = 1 MSPS Typically 10 nA, VIN = 0 V or VDRIVE AD7904/AD7914/AD7924 Parameter LOGIC OUTPUTS Output High Voltage, VOH Output Low Voltage, VOL Floating-State Leakage Current Floating-State Output Capacitance3 Output Coding CONVERSION RATE Conversion Time Track-and-Hold Acquisition Time2 Throughput Rate POWER REQUIREMENTS VDD VDRIVE IDD 4 Normal Mode (Static) Normal Mode (Operational) Auto Shutdown Mode Full Shutdown Mode Power Dissipation4 Normal Mode (Operational) Auto Shutdown Mode (Static) Full Shutdown Mode B Version 1 Unit Test Conditions/Comments VDRIVE - 0.2 V min 0.4 V max 1 A max 10 pF max Straight (natural) binary Twos complement ISOURCE = 200 A, AVDD = 2.7 V to 5.25 V ISINK = 200 A 800 300 300 1 ns max ns max ns max MSPS max 16 SCLK cycles with SCLK at 20 MHz Sine wave input Full-scale step input See the Serial Interface section 2.7/5.25 2.7/5.25 V min/V max V min/V max 600 2.7 2 960 0.5 0.5 A typ mA max mA max A typ A max A max Digital inputs = 0 V or VDRIVE AVDD = 2.7 V to 5.25 V, SCLK on or off AVDD = 4.75 V to 5.25 V, fSCLK = 20 MHz AVDD = 2.7 V to 3.6 V, fSCLK = 20 MHz fSAMPLE = 250 kSPS Static SCLK on or off (20 nA typ) 13.5 6 2.5 1.5 2.5 1.5 mW max mW max W max W max W max W max AVDD = 5 V, fSCLK = 20 MHz AVDD = 3 V, fSCLK = 20 MHz AVDD = 5 V AVDD = 3 V AVDD = 5 V AVDD = 3 V 1 Temperature range for B versions: -40C to +85C. See the Terminology section. 3 Sample tested @ 25C to ensure compliance. 4 See the Power vs. Throughput Rate section. 2 Rev. B | Page 6 of 32 CODING bit set to 1 CODING bit set to 0 AD7904/AD7914/AD7924 AD7924 SPECIFICATIONS AVDD = VDRIVE = 2.7 V to 5.25 V, REFIN = 2.5 V, fSCLK = 20 MHz, TA = TMIN to TMAX, unless otherwise noted. Table 3. Parameter DYNAMIC PERFORMANCE Signal to (Noise + Distortion) (SINAD) 2 Signal-to-Noise Ratio (SNR) Total Harmonic Distortion (THD)2 Peak Harmonic or Spurious Noise (SFDR) Intermodulation Distortion (IMD) Second-Order Terms Third-Order Terms Aperture Delay Aperture Jitter Channel-to-Channel Isolation2 Full Power Bandwidth DC ACCURACY Resolution Integral Nonlinearity (INL)2 Differential Nonlinearity (DNL)2 0 V to REFIN Input Range Offset Error2 Offset Error Match2 Gain Error2 Gain Error Match2 0 V to 2 x REFIN Input Range Positive Gain Error2 Positive Gain Error Match2 Zero Code Error2 Zero Code Error Match2 Negative Gain Error2 Negative Gain Error Match2 ANALOG INPUT Input Voltage Range DC Leakage Current Input Capacitance REFERENCE INPUT REFIN Input Voltage DC Leakage Current REFIN Input Impedance LOGIC INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Current, IIN Input Capacitance, CIN 3 B Version 1 Unit 70 69.5 69 70 69.5 -77 -73 -78 dB min dB min dB min dB min dB min dB max dB max dB max -90 -90 10 50 -85 8.2 1.6 dB typ dB typ ns typ ps typ dB typ MHz typ MHz typ 12 1 -0.9/+1.5 Bits LSB max LSB max 8 0.5 1.5 0.5 LSB max LSB max LSB max LSB max Test Conditions/Comments fIN = 50 kHz sine wave, fSCLK = 20 MHz @ 5 V, B models @ 5 V, W models @ 3 V, typically 69.5 dB B models W models @ 5 V, typically -84 dB @ 3 V, typically -77 dB @ 5 V, typically -86 dB fa = 40.1 kHz, fb = 41.5 kHz fIN = 400 kHz @ 3 dB @ 0.1 dB Guaranteed no missed codes to 12 bits Straight binary output coding Typically 0.5 LSB -REFIN to +REFIN biased about REFIN with twos complement output coding 1.5 0.5 8 0.5 1 0.5 LSB max LSB max LSB max LSB max LSB max LSB max 0 to REFIN 0 to 2 x REFIN 1 20 V V A max pF typ RANGE bit set to 1 RANGE bit set to 0, AVDD/VDRIVE = 4.75 V to 5.25 V 2.5 1 36 V A max k typ 1% specified performance 0.7 x VDRIVE 0.3 x VDRIVE 1 10 V min V max A max pF max Rev. B | Page 7 of 32 Typically 0.8 LSB fSAMPLE = 1 MSPS Typically 10 nA, VIN = 0 V or VDRIVE AD7904/AD7914/AD7924 Parameter LOGIC OUTPUTS Output High Voltage, VOH Output Low Voltage, VOL Floating-State Leakage Current Floating-State Output Capacitance3 Output Coding CONVERSION RATE Conversion Time Track-and-Hold Acquisition Time2 Throughput Rate POWER REQUIREMENTS VDD VDRIVE IDD 4 Normal Mode (Static) Normal Mode (Operational) Auto Shutdown Mode Full Shutdown Mode Power Dissipation4 Normal Mode (Operational) Auto Shutdown Mode (Static) Full Shutdown Mode B Version 1 Unit Test Conditions/Comments VDRIVE - 0.2 V min 0.4 V max 1 A max 10 pF max Straight (natural) binary Twos complement ISOURCE = 200 A, AVDD = 2.7 V to 5.25 V ISINK = 200 A 800 300 300 1 ns max ns max ns max MSPS max 16 SCLK cycles with SCLK at 20 MHz Sine wave input Full-scale step input See the Serial Interface section 2.7/5.25 2.7/5.25 V min/V max V min/V max 600 2.7 2 960 0.5 0.5 A typ mA max mA max A typ A max A max Digital inputs = 0 V or VDRIVE AVDD = 2.7 V to 5.25 V, SCLK on or off AVDD = 4.75 V to 5.25 V, fSCLK = 20 MHz AVDD = 2.7 V to 3.6 V, fSCLK = 20 MHz fSAMPLE = 250 kSPS Static SCLK on or off (20 nA typ) 13.5 6 2.5 1.5 2.5 1.5 mW max mW max W max W max W max W max AVDD = 5 V, fSCLK = 20 MHz AVDD = 3 V, fSCLK = 20 MHz AVDD = 5 V AVDD = 3 V AVDD = 5 V AVDD = 3 V 1 Temperature range for B versions: -40C to +85C. See the Terminology section. 3 Sample tested @ 25C to ensure compliance. 4 See the Power vs. Throughput Rate section. 2 Rev. B | Page 8 of 32 CODING bit set to 1 CODING bit set to 0 AD7904/AD7914/AD7924 TIMING SPECIFICATIONS AVDD = 2.7 V to 5.25 V, VDRIVE AVDD, REFIN = 2.5 V, TA = TMIN to TMAX, unless otherwise noted. Table 4. Parameter 1 fSCLK 2 tCONVERT tQUIET AVDD = 3 V 10 20 16 x tSCLK 50 t2 t3 3 t4 3 t5 t6 t7 t8 4 t9 t10 t11 t12 10 35 40 0.4 x tSCLK 0.4 x tSCLK 10 15/45 10 5 20 1 Limit at TMIN, TMAX AVDD = 5 V 10 20 16 x tSCLK 50 10 30 40 0.4 x tSCLK 0.4 x tSCLK 10 15/35 10 5 20 1 Unit kHz min MHz max Description ns min Minimum quiet time required between the CS rising edge and the start of the next conversion CS to SCLK setup time Delay from CS until DOUT three-state disabled Data access time after SCLK falling edge SCLK low pulse width SCLK high pulse width SCLK to DOUT valid hold time SCLK falling edge to DOUT high impedance DIN setup time prior to SCLK falling edge DIN hold time after SCLK falling edge 16th SCLK falling edge to CS high Power-up time from full shutdown/auto shutdown modes ns min ns max ns max ns min ns min ns min ns min/ns max ns min ns min ns min s max 1 Sample tested @ 25C to ensure compliance. All input signals are specified with tR = tF = 5 ns (10% to 90% of AVDD) and timed from a voltage level of 1.6 V (see Figure 2). The 3 V operating range spans from 2.7 V to 3.6 V. The 5 V operating range spans from 4.75 V to 5.25 V. 2 Mark/space ratio for the SCLK input is 40/60 to 60/40. 3 Measured with the load circuit of Figure 2 and defined as the time required for the output to cross 0.4 V or 0.7 x VDRIVE. 4 t8 is derived from the measured time taken by the data outputs to change 0.5 V when loaded with the circuit of Figure 2. The measured number is then extrapolated back to remove the effects of charging or discharging the 50 pF capacitor. This means that the time, t8, quoted in the timing characteristics is the true bus relinquish time of the part and is independent of the bus loading. 200A 1.6V CL 50pF 200A IOH 03087-002 TO OUTPUT PIN IOL Figure 2. Load Circuit for Digital Output Timing Specifications Rev. B | Page 9 of 32 AD7904/AD7914/AD7924 ABSOLUTE MAXIMUM RATINGS TA = 25C, unless otherwise noted. Table 5. Parameter AVDD to AGND VDRIVE to AGND Analog Input Voltage to AGND Digital Input Voltage to AGND Digital Output Voltage to AGND REFIN to AGND Input Current to Any Pin Except Supplies1 Operating Temperature Range Commercial (B Version) Automotive (W Version) Storage Temperature Range Junction Temperature TSSOP Package, Power Dissipation JA Thermal Impedance JC Thermal Impedance Lead Temperature, Soldering Vapor Phase (60 secs) Infrared (15 secs) ESD 1 Rating -0.3 V to +7 V -0.3 V to AVDD + 0.3 V -0.3 V to AVDD + 0.3 V -0.3 V to +7 V -0.3 V to AVDD + 0.3 V -0.3 V to AVDD + 0.3 V 10 mA Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION -40C to +85C -40C to +125C -65C to +150C 150C 450 mW 150.4C/W (TSSOP) 27.6C/W (TSSOP) 215C 220C 1.5 kV Transient currents of up to 100 mA will not cause SCR latch-up. Rev. B | Page 10 of 32 AD7904/AD7914/AD7924 SCLK 1 16 AGND DIN 2 15 VDRIVE 14 DOUT CS 3 AGND 4 AVDD 5 AD7904/ AD7914/ AD7924 TOP VIEW (Not to Scale) 13 AGND 12 VIN0 VIN1 AVDD 6 11 REFIN 7 10 VIN2 AGND 8 9 VIN3 03087-003 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS Figure 3. Pin Configuration Table 6. Pin Function Descriptions Pin No. 1 Mnemonic SCLK 2 DIN 3 CS 4, 8, 13, 16 AGND 5, 6 AVDD 7 REFIN 9, 10, 11, 12 VIN3, VIN2, VIN1, VIN0 14 DOUT 15 VDRIVE Function Serial Clock, Logic Input. SCLK provides the serial clock for accessing data from the part. This clock input is also used as the clock source for the AD7904/AD7914/AD7924 conversion process. Data In, Logic Input. Data to be written to the control register of the AD7904/AD7914/AD7924 is provided on this input and is clocked into the register on the falling edge of SCLK (see the Control Register section). Chip Select. Active low logic input. This input provides the dual function of initiating conversions on the AD7904/AD7914/AD7924 and frames the serial data transfer. Analog Ground. Ground reference point for all analog circuitry on the AD7904/AD7914/AD7924. All analog input signals and any external reference signal should be referred to this AGND voltage. All AGND pins should be connected together. Analog Power Supply Input. The AVDD range for the AD7904/AD7914/AD7924 is from 2.7 V to 5.25 V. For the 0 V to 2 x REFIN range, AVDD should be from 4.75 V to 5.25 V. Reference Input for the AD7904/AD7914/AD7924. An external reference must be applied to this input. The voltage range for the external reference is 2.5 V 1% for specified performance. Analog Input 0 through Analog Input 3. The four single-ended analog input channels are multiplexed into the on-chip track-and-hold. The analog input channel to be converted is selected using the address bits ADD1 and ADD0 of the control register. The address bits, in conjunction with the SEQ1 and SEQ0 bits, allow the sequencer to be programmed. The input range for all input channels can extend from 0 V to REFIN or from 0 V to 2 x REFIN as selected via the RANGE bit in the control register. Any unused input channels should be connected to AGND to avoid noise pickup. Data Out, Logic Output. The conversion result from the AD7904/AD7914/AD7924 is provided on this output as a serial data stream. The bits are clocked out on the falling edge of the SCLK input. The data stream from the AD7904 consists of two leading zeros, two address bits indicating which channel the conversion result corresponds to, followed by the eight bits of conversion data, followed by four trailing zeros, provided MSB first. The data stream from the AD7914 consists of two leading zeros, two address bits indicating which channel the conversion result corresponds to, followed by the 10 bits of conversion data, followed by two trailing zeros, provided MSB first. The data stream from the AD7924 consists of two leading zeros, two address bits indicating which channel the conversion result corresponds to, followed by the 12 bits of conversion data, provided MSB first. The output coding can be selected as straight binary or twos complement via the CODING bit in the control register. Logic Power Supply Input. The voltage supplied at this pin determines the voltage at which the serial interface of the AD7904/AD7914/AD7924 operates. Rev. B | Page 11 of 32 AD7904/AD7914/AD7924 TYPICAL PERFORMANCE CHARACTERISTICS -30 fSAMPLE = 1MSPS TA = 25C RANGE = 0V TO REFIN -55 AVDD = VDRIVE = 2.7V -60 -65 -50 THD (dB) SNR (dB) -50 4096 POINT FFT AVDD = 5V fSAMPLE = 1MSPS fIN = 50kHz SINAD = 71.147dB THD = -87.229dB SFDR = -90.744dB -10 -70 AVDD = VDRIVE = 3.6V -70 -75 -80 -90 AVDD = VDRIVE = 4.75V -85 50 100 150 200 250 300 350 400 450 500 FREQUENCY (kHz) Figure 4. AD7924 Dynamic Performance at 1 MSPS AVDD = VDRIVE = 5.25V -90 10 100 1000 INPUT FREQUENCY (kHz) 03087-007 0 03087-004 -110 Figure 7. AD7924 THD vs. Analog Input Frequency for Various Supply Voltages at 1 MSPS 75 -50 AVDD = VDRIVE = 5.25V fSAMPLE = 1MSPS TA = 25C RANGE = 0V TO REFIN AVDD = 5.25V -55 AVDD = VDRIVE = 4.75V 70 -60 AVDD = VDRIVE = 3.6V THD (dB) 65 RIN = 100 RIN = 50 -75 60 -80 AVDD = VDRIVE = 2.7V 55 10 100 -90 10 03087-005 TA = 25C RANGE = 0V TO REFIN 1000 INPUT FREQUENCY (kHz) Figure 5. AD7924 SINAD vs. Analog Input Frequency for Various Supply Voltages at 1 MSPS, SCLK = 20 MHz 100 1000 INPUT FREQUENCY (kHz) Figure 8. AD7924 THD vs. Analog Input Frequency for Various Source Impedances 0 1.0 AVDD = 5V 200mV p-p SINE WAVE ON AVDD REFIN = 2.5V, 1F CAPACITOR TA = 25C -10 -20 TA = 25C AVDD = VDRIVE = 5V 0.8 0.6 0.4 INL ERROR (LSB) -30 -40 -50 -60 -70 0.2 0 -0.2 -0.4 -0.6 -80 -0.8 0 100 200 300 400 500 600 700 800 900 03087-006 -90 RIN = 10 -85 03087-008 fSAMPLE = 1MSPS PSRR (dB) -70 1000 SUPPLY RIPPLE FREQUENCY (kHz) Figure 6. AD7924 PSRR vs. Supply Ripple Frequency (No Decoupling) Rev. B | Page 12 of 32 -1.0 0 512 1024 1536 2048 2560 3072 CODE Figure 9. AD7924 Typical INL 3584 4096 03087-009 SINAD (dB) RIN = 1000 -65 AD7904/AD7914/AD7924 1.0 TA = 25C AVDD = VDRIVE = 5V 0.8 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1.0 0 512 1024 1536 2048 2560 3072 CODE 3584 4096 03087-010 DNL ERROR (LSB) 0.6 Figure 10. AD7924 Typical DNL Rev. B | Page 13 of 32 AD7904/AD7914/AD7924 TERMINOLOGY Integral Nonlinearity (INL) INL is the maximum deviation from a straight line passing through the endpoints of the ADC transfer function. The endpoints of the transfer function are zero scale, a point 1 LSB below the first code transition, and full scale, a point 1 LSB above the last code transition. Differential Nonlinearity (DNL) DNL is the difference between the measured and the ideal 1 LSB change between any two adjacent codes in the ADC. Offset Error Offset error is the deviation of the first code transition (00 ... 000 to 00 ... 001) from the ideal, that is, AGND + 1 LSB. Offset Error Match Offset error match is the difference in offset error between any two channels. Gain Error Gain error is the deviation of the last code transition (111 ... 110 to 111 ... 111) from the ideal, that is, REFIN - 1 LSB, after the offset error has been adjusted out. Gain Error Match Gain error match is the difference in gain error between any two channels. Zero Code Error Zero code error is the deviation of the midscale transition (all 0s to all 1s) from the ideal VIN voltage, that is, REFIN - 1 LSB. It applies when using the twos complement output coding option with the 2 x REFIN input range (-REFIN to +REFIN biased about the REFIN point). Zero Code Error Match Zero code error match is the difference in zero code error between any two channels. Positive Gain Error Positive gain error is the deviation of the last code transition (011 ... 110 to 011 ... 111) from the ideal, that is, +REFIN - 1 LSB, after the zero code error is adjusted out. It applies when using the twos complement output coding option with the 2 x REFIN input range (-REFIN to +REFIN biased about the REFIN point). Positive Gain Error Match Positive gain error match is the difference in positive gain error between any two channels. Negative Gain Error Negative gain error is the deviation of the first code transition (100 ... 000 to 100 ... 001) from the ideal, that is, -REFIN + 1 LSB, after the zero code error is adjusted out. It applies when using the twos complement output coding option with the 2 x REFIN input range (-REFIN to +REFIN biased about the REFIN point). Negative Gain Error Match Negative gain error match is the difference in negative gain error between any two channels. Channel-to-Channel Isolation Channel-to-channel isolation is a measure of the level of crosstalk between channels. It is measured by applying a full-scale 400 kHz sine wave signal to all three nonselected input channels and determining how much that signal is attenuated in the selected channel with a 50 kHz signal. The figure is given worst case across all four channels for the AD7904/AD7914/AD7924. Power Supply Rejection (PSR) Variations in power supply affect the full-scale transition but not the linearity of the converter. PSR is the maximum change in the full-scale transition point due to a change in power supply voltage from the nominal value (see Figure 6). Power Supply Rejection Ratio (PSRR) PSRR is the ratio of the power in the ADC output at full-scale frequency, f, to the power of a 200 mV p-p sine wave applied to the ADC AVDD supply of frequency fS. PSRR(dB) = 10 log(Pf/Pfs) where: Pf is the power at frequency f in the ADC output. PfS is the power at frequency fS coupled onto the ADC AVDD supply. Track-and-Hold Acquisition Time The track-and-hold amplifier returns to track mode at the end of a conversion. Track-and-hold acquisition time is the time required for the output of the track-and-hold amplifier to reach its final value, within 1 LSB, after the end of a conversion. Signal to (Noise + Distortion) (SINAD) Ratio SINAD is the measured ratio of signal to (noise + distortion) at the output of the ADC. The signal is the rms amplitude of the fundamental. Noise is the sum of all nonfundamental signals up to half the sampling frequency (fS/2), excluding dc. The ratio is dependent on the number of quantization levels in the digitization process: the more levels, the smaller the quantization noise. The theoretical SINAD ratio for an ideal N-bit converter with a sine wave input is given by Signal to (Noise + Distortion) = (6.02 N +1.76) dB Thus, for a 12-bit converter, SINAD is 74 dB, for a 10-bit converter, it is 62 dB, and for an 8-bit converter, it is 50 dB. Total Harmonic Distortion (THD) THD is the ratio of the rms sum of harmonics to the fundamental. For the AD7904/AD7914/AD7924, it is defined as THD(dB) = 20 log V2 2 + V3 2 + V 4 2 + V5 2 + V6 2 V1 where: V1 is the rms amplitude of the fundamental. V2, V3, V4, V5, and V6 are the rms amplitudes of the second through the sixth harmonics. Rev. B | Page 14 of 32 AD7904/AD7914/AD7924 CONTROL REGISTER The control register of the AD7904/AD7914/AD7924 is a 12-bit, write-only register. Data is loaded from the DIN pin of the AD7904/AD7914/AD7924 on the falling edge of SCLK. The data is transferred on the DIN line at the same time that the conversion result is read from the part. The data transferred on the DIN line corresponds to the AD7904/AD7914/AD7924 configuration for the next conversion. This requires 16 serial clocks for every data transfer. Only the information provided on the first 12 falling clock edges (after the CS falling edge) is loaded to the control register. MSB denotes the first bit in the data stream. The bit functions are outlined in Table 8. Table 7. Channel Selection ADD1 0 0 1 1 ADD0 0 1 0 1 Analog Input Channel VIN0 VIN1 VIN2 VIN3 Table 8. Control Register Bit Functions MSB 11 WRITE 10 SEQ1 Bit 11 Mnemonic WRITE 10 [9:8] [7:6] SEQ1 DONTC ADD1, ADD0 [5:4] PM1, PM0 3 2 1 SEQ0 DONTC RANGE 0 CODING 9 DONTC 8 DONTC 7 ADD1 6 ADD0 5 PM1 4 PM0 3 SEQ0 2 DONTC 1 RANGE LSB 0 CODING Description The value written to this bit determines whether the following 11 bits will be loaded to the control register. If this bit is set to 1, the following 11 bits will be written to the control register; if this bit is set to 0, the remaining 11 bits are not loaded to the control register, which remains unchanged. The SEQ1 bit is used in conjunction with the SEQ0 bit to control the use of the sequencer function (see Table 10). Don't care bits. The two address bits are loaded at the end of the present conversion sequence and select which analog input channel is to be converted in the next serial transfer, or they may select the final channel in a consecutive sequence as described in Table 10. The selected input channel is decoded as shown in Table 7. The address bits corresponding to the conversion result are also output on DOUT prior to the 12 bits of data (see the Serial Interface section). The next channel to be converted on will be selected by the mux on the 14th SCLK falling edge. The two power management bits decode the mode of operation of the AD7904/AD7914/AD7924 as described in Table 9. The SEQ0 bit is used in conjunction with the SEQ1 bit to control the use of the sequencer function (see Table 10). Don't care bit. This bit selects the analog input range to be used on the AD7904/AD7914/AD7924. If it is set to 0, the analog input range will extend from 0 V to 2 x REFIN. If it is set to 1, the analog input range will extend from 0 V to REFIN (for the next conversion). For the 0 V to 2 x REFIN input range, VDD = 4.75 V to 5.25 V. This bit selects the type of output coding that the AD7904/AD7914/AD7924 will use for the conversion result. If this bit is set to 0, the output coding for the part will be twos complement. If this bit is set to 1, the output coding from the part will be straight binary (for the next conversion). Table 9. Power Mode Selection PM1 1 PM0 1 Mode Normal operation 1 0 Full shutdown 0 1 Auto shutdown 0 0 Invalid Description In normal operation mode, the AD7904/AD7914/AD7924 remain in full power mode regardless of the status of any of the logic inputs. This mode allows the fastest possible throughput rate from the AD7904/AD7914/AD7924. In full shutdown mode, the AD7904/AD7914/AD7924 are in full shutdown with all circuitry on the device powering down. The AD7904/AD7914/AD7924 retain the information in the control register while in full shutdown. The part remains in full shutdown until these bits are changed. In auto shutdown mode, the AD7904/AD7914/AD7924 automatically enter full shutdown mode at the end of each conversion when the control register is updated. Wake-up time from full shutdown is 1 s; the user should ensure that 1 s has elapsed before attempting to perform a valid conversion on the part in this mode. Invalid selection. This configuration is not allowed. Rev. B | Page 15 of 32 AD7904/AD7914/AD7924 SEQUENCER OPERATION The SEQ1 and SEQ0 bits in the control register allow the user to select a mode of operation for the sequencer function. Table 10 outlines the three modes of operation of the sequencer. Figure 11 shows the traditional operation of a multichannel ADC, where each serial transfer selects the next channel for conversion. In this mode of operation, the sequencer function is not used. Figure 12 shows how to program the AD7904/AD7914/AD7924 to continuously convert on a sequence of consecutive channels from Channel 0 to a selected final channel. To exit this mode of operation and revert to the traditional mode of operation of a multichannel ADC (as shown in Figure 11), ensure that the WRITE bit = 1 and SEQ1 = SEQ0 = 0 on the next serial transfer. Table 10. Sequence Selection SEQ1 0 SEQ0 X Sequencer Function Not used 1 0 Used (not interrupted upon completion) 1 1 Continuous conversions Description The sequencer function is not used. The analog input channel selected for each individual conversion is determined by the contents of the channel address bits, ADD1 and ADD0, in each previous write operation. This mode of operation reflects the traditional operation of a multichannel ADC, without using the sequencer function, where each write to the AD7904/AD7914/ AD7924 selects the next channel for conversion (see Figure 11). The sequencer function is not interrupted upon completion of the write operation. This configuration allows other bits in the control register to be altered between conversions while in a sequence without terminating the cycle. This configuration is used in conjunction with the channel address bits, ADD1 and ADD0, to program continuous conversions on a consecutive sequence of channels from Channel 0 to a selected final channel that is specified by the channel address bits in the control register (see Figure 12). POWER ON DUMMY CONVERSION CS DIN: WRITE TO CONTROL REGISTER, WRITE BIT = 1, SELECT CODING, RANGE, AND POWER MODE. SELECT CHANNEL ADD1, ADD0 FOR CONVERSION. SEQ1 = 0, SEQ0 = x CS DIN: WRITE TO CONTROL REGISTER, WRITE BIT = 1, SELECT CODING, RANGE, AND POWER MODE. SELECT ADD1, ADD0 FOR CONVERSION. SEQ1 = 0, SEQ0 = x WRITE BIT = 1, SEQ1 = 0, SEQ0 = x Figure 11. SEQ1 Bit = 0, SEQ0 Bit = x Flowchart Rev. B | Page 16 of 32 03087-011 DOUT: CONVERSION RESULT FROM PREVIOUSLY SELECTED CHANNEL ADD1, ADD0 AD7904/AD7914/AD7924 POWER ON DUMMY CONVERSION CS DIN: WRITE TO CONTROL REGISTER, WRITE BIT = 1, SELECT CODING, RANGE, AND POWER MODE. SELECT CHANNEL ADD1, ADD0 FOR CONVERSION. SEQ1 = 1, SEQ0 = 1 DOUT: CONVERSION RESULT FROM CHANNEL 0 CS CONTINUOUSLY CONVERTS ON A CONSECUTIVE SEQUENCE OF CHANNELS FROM CHANNEL 0 UP TO AND INCLUDING THE PREVIOUSLY SELECTED ADD1, ADD0 IN THE CONTROL REGISTER WRITE BIT = 0 CONTINUOUSLY CONVERTS ON THE SELECTED SEQUENCE OF CHANNELS BUT WILL ALLOW RANGE, CODING, AND SO FORTH, TO CHANGE IN THE CONTROL REGISTER WITHOUT INTERRUPTING WRITE BIT = 1, THE SEQUENCE, PROVIDED SEQ1 = 1, SEQ0 = 0 SEQ1 = 1, SEQ0 = 0 Figure 12. SEQ1 Bit = 1, SEQ0 Bit = 1 Flowchart Rev. B | Page 17 of 32 03087-012 CS AD7904/AD7914/AD7924 CIRCUIT INFORMATION The AD7904/AD7914/AD7924 provide the user with an on-chip track-and-hold ADC and serial interface housed in a 16-lead TSSOP package. The AD7904/AD7914/AD7924 each have four single-ended input channels with a channel sequencer, allowing the user to select a channel sequence through which the ADC can cycle with each consecutive CS falling edge. The serial clock input accesses data from the part, controls the transfer of data written to the ADC, and provides the clock source for the successive approximation ADC. The analog input range for the AD7904/ AD7914/AD7924 is 0 V to REFIN or 0 V to 2 x REFIN, depending on the status of Bit 1 in the control register. For the 0 V to 2 x REFIN range, the part must be operated from a 4.75 V to 5.25 V supply. The AD7904/AD7914/AD7924 provide flexible power management options to allow the user to achieve the best power performance for a given throughput rate. These options are selected by programming the power management bits, PM1 and PM0, in the control register. CONVERTER OPERATION The AD7904/AD7914/AD7924 are 8-, 10-, and 12-bit SAR ADCs, respectively, based around a capacitive DAC. The AD7904/ AD7914/AD7924 can convert analog input signals in the range of 0 V to REFIN or 0 V to 2 x REFIN. Figure 13 and Figure 14 show simplified schematics of the ADC. The AD7904/AD7914/ AD7924 include control logic, the SAR ADC, and a capacitive DAC, which are used to add and subtract fixed amounts of charge from the sampling capacitor to bring the comparator back into a balanced condition. Figure 13 shows the ADC during its acquisition phase. SW2 is closed and SW1 is in Position A. The comparator is held in a balanced condition and the sampling capacitor acquires the signal on the selected VIN channel. CAPACITIVE DAC VIN3 4k A SW1 B CONTROL LOGIC SW2 COMPARATOR AGND CAPACITIVE DAC 4k A VIN0 SW1 B CONTROL LOGIC SW2 VIN3 COMPARATOR AGND Figure 14. ADC Conversion Phase Analog Input Figure 15 shows an equivalent circuit of the analog input structure of the AD7904/AD7914/AD7924. The two diodes, D1 and D2, provide ESD protection for the analog inputs. Care must be taken to ensure that the analog input signal never exceeds the supply rails by more than 200 mV. This will cause these diodes to become forward-biased and start conducting current into the substrate. The maximum current that these diodes can conduct without causing irreversible damage to the part is 10 mA. Capacitor C1 in Figure 15 is typically about 4 pF and can primarily be attributed to pin capacitance. The resistor, R1, is a lumped component made up of the on resistance of a track-and-hold switch and the on resistance of the input multiplexer. The total resistance is typically about 400 . Capacitor C2 is the ADC sampling capacitor and has a capacitance of 30 pF typically. For ac applications, removing high frequency components from the analog input signal is recommended by use of a low-pass RC filter on the relevant analog input pin. In applications where harmonic distortion and signal-to-noise ratio are critical, the analog input should be driven from a low impedance source. Large source impedances significantly affect the ac performance of the ADC. This may necessitate the use of an input buffer amplifier. The choice of the op amp is a function of the particular application. When no amplifier is used to drive the analog input, the source impedance should be limited to low values. The maximum source impedance depends on the amount of total harmonic distortion (THD) that can be tolerated. The THD increases as the source impedance increases, and performance will degrade (see Figure 8). AVDD 03087-013 VIN0 condition. When the comparator is rebalanced, the conversion is complete. The control logic generates the ADC output code. Figure 16 and Figure 17 show the ADC transfer functions. 03087-014 The AD7904/AD7914/AD7924 are, respectively, 8-bit, 10-bit, and 12-bit, high speed, 4-channel, single-supply ADCs. The parts can be operated from a 2.7 V to 5.25 V supply. When operated from either a 5 V or 3 V supply, the AD7904/AD7914/AD7924 are capable of throughput rates of 1 MSPS when provided with a 20 MHz clock. D1 Figure 13. ADC Acquisition Phase VIN Rev. B | Page 18 of 32 C1 4pF D2 C2 30pF CONVERSION PHASE: SWITCH OPEN TRACK PHASE: SWITCH CLOSED 03087-015 When the ADC starts a conversion (see Figure 14), SW2 opens and SW1 moves to position B, causing the comparator to become unbalanced. The control logic and the capacitive DAC are used to add and subtract fixed amounts of charge from the sampling capacitor to bring the comparator back into a balanced R1 Figure 15. Equivalent Analog Input Circuit AD7904/AD7914/AD7924 ADC TRANSFER FUNCTION 111...111 111...110 * * 111...000 * 011...111 * * 000...010 000...001 000...000 1LSB +VREF - 1LSB ANALOG INPUT NOTES 1. VREF IS EITHER REFIN OR 2 x REFIN. Figure 17. Twos Complement Transfer Characteristic with 0 V to 2 x REFIN Input Range Handling Bipolar Input Signals Figure 18 shows how the combination of the 0 V to 2 x REFIN input range and the twos complement output coding scheme is particularly useful for handling bipolar input signals. If the bipolar input signal is biased about REFIN and twos complement output coding is selected, REFIN becomes the zero code point, -REFIN is negative full scale, and +REFIN becomes positive full scale, with a dynamic range of 2 x REFIN. Figure 16. Straight Binary Transfer Characteristic VDD VREF 0.1F AV REFIN DD VDD VDRIVE AD7904/ AD7914/ AD7924 R3 0V V VIN0 R2 R1 R1 = R2 = R3 = R4 DOUT VIN3 DSP/ MICROPROCESSOR TWOS COMPLEMENT +REFIN (= 2 x REFIN) 000...000 REFIN -REFIN Figure 18. Handling Bipolar Signals Rev. B | Page 19 of 32 011...111 (= 0V) 100...000 03087-018 R4 V 03087-017 ADC CODE 1LSB = 2 x VREF /256 AD7904 1LSB = 2 x VREF /1024 AD7914 1LSB = 2 x VREF /4096 AD7924 -VREF + 1LSB +VREF - 1LSB VREF - 1LSB ANALOG INPUT 1LSB = VREF /256 AD7904 1LSB = VREF /1024 AD7914 1LSB = VREF /4096 AD7924 0V 011...111 011...110 * * 000...001 000...000 111...111 * * 100...010 100...001 100...000 03087-016 ADC CODE The output coding of the AD7904/AD7914/AD7924 is either straight binary or twos complement, depending on the status of the LSB in the control register. The designed code transitions occur at successive LSB values (that is, 1 LSB, 2 LSBs, and so on). For the 0 V to REFIN input range, the LSB size is REFIN/256 for the AD7904, REFIN/1024 for the AD7914, and REFIN/4096 for the AD7924. For the 0 V to 2 x REFIN input range, the LSB size is 2 x REFIN/256 for the AD7904, 2 x REFIN/1024 for the AD7914, and 2 x REFIN/4096 for the AD7924. The ideal transfer characteristic for the AD7904/AD7914/AD7924 when straight binary coding is selected is shown in Figure 16; the ideal transfer characteristic for the AD7904/AD7914/AD7924 when twos complement coding is selected is shown in Figure 17. AD7904/AD7914/AD7924 TYPICAL CONNECTION DIAGRAM Analog Input Selection Figure 19 shows a typical connection diagram for the AD7904/ AD7914/AD7924. In this setup, the AGND pin is connected to the analog ground plane of the system. In Figure 19, the REFIN pin is connected to a decoupled 2.5 V supply from a reference source, the AD780, to provide an analog input range of 0 V to 2.5 V (if the RANGE bit is set to 1) or 0 V to 5 V (if the RANGE bit is set to 0). Any one of four analog input channels can be selected for conversion by programming the multiplexer with the address bits ADD1 and ADD0 in the control register. The channel configurations are shown in Table 7. Although the AD7904/AD7914/AD7924 are connected to a VDD of 5 V, the serial interface is connected to a 3 V microprocessor. The VDRIVE pin of the AD7904/AD7914/AD7924 is connected to the same 3 V supply as the microprocessor to allow a 3 V logic interface (see the Digital Inputs section). The conversion result is output in a 16-bit word. This 16-bit data stream consists of two leading zeros, two address bits indicating which channel the conversion result corresponds to, followed by the 12 bits of conversion data for the AD7924 (10 bits of data for the AD7914 and 8 bits of data for the AD7904, each followed by two and four trailing zeros, respectively). For applications where power consumption is of concern, the power-down modes should be used between conversions or bursts of several conversions to improve power performance (see the Modes of Operation section). 0.1F 5V SUPPLY 10F SERIAL INTERFACE VIN3 AVDD SCLK AD7904/ AD7914/ AD7924 AGND REF IN 0.1F 2.5V AD780 MICROCONTROLLER/ MICROPROCESSOR DOUT CS VDRIVE DIN 0.1F 10F 3V SUPPLY NOTES 1. ALL UNUSED INPUT CHANNELS SHOULD BE CONNECTED TO AGND. Figure 19. Typical Connection Diagram 03087-019 VIN0 0V TO REFIN The AD7904/AD7914/AD7924 can also be configured to automatically cycle through a number of selected channels. The sequencer feature is accessed via the SEQ1 and SEQ0 bits in the control register (see Table 10). The AD7904/AD7914/AD7924 can be programmed to continuously convert on a number of consecutive channels in ascending order from Channel 0 to a selected final channel as determined by the channel address bits, ADD1 and ADD0. This is possible if the SEQ1 and SEQ0 bits are set to 11. The next serial transfer will then act on the sequence programmed by executing a conversion on Channel 0. The next serial transfer will result in a conversion on Channel 1, and so on, until the channel selected via the address bits, ADD1 and ADD0, is reached. It is not necessary to write to the control register again after a sequence operation has been initiated. To ensure that the control register is not accidently overwritten or the sequence operation interrupted, the WRITE bit must be set to 0 or the DIN line must be tied low. If the control register is written to at any time during the sequence, the SEQ1 and SEQ0 bits must be set to 10 to avoid interrupting the automatic conversion sequence. This pattern continues until the AD7904/AD7914/AD7924 are written to and the SEQ1 and SEQ0 bits are configured with a bit combination other than 10, resulting in the termination of the sequence. If the sequence is uninterrupted (WRITE bit = 0, or WRITE bit = 1 and SEQ1 and SEQ0 bits are set to 10), then upon completion of the sequence, the AD7904/AD7914/AD7924 sequencer returns to Channel 0 and restarts the sequence. Regardless of the channel selection method used, the 16-bit word output from the AD7924 during each conversion always contains two leading zeros, two channel address bits that the conversion result corresponds to, followed by the 12-bit conversion result; the AD7914 outputs two leading zeros, two channel address bits that the conversion result corresponds to, followed by the 10-bit conversion result and two trailing zeros; the AD7904 outputs two leading zeros, two channel address bits that the conversion result corresponds to, followed by the 8-bit conversion result and four trailing zeros (see the Serial Interface section). Rev. B | Page 20 of 32 AD7904/AD7914/AD7924 Digital Inputs The digital inputs applied to the AD7904/AD7914/AD7924 can go to 7 V and are not restricted by the AVDD + 0.3 V limit on the analog inputs. Because the SCLK, DIN, and CS inputs are not restricted by the AVDD + 0.3 V limit, power supply sequencing issues are avoided. If CS, DIN, or SCLK is applied before AVDD, there is no risk of latch-up as there would be on the analog inputs if a signal greater than 0.3 V is applied prior to AVDD. VDRIVE The AD7904/AD7914/AD7924 also include the VDRIVE feature. VDRIVE controls the voltage at which the serial interface operates. VDRIVE allows the ADC to easily interface to both 3 V and 5 V processors. For example, if the AD7904/AD7914/AD7924 are operated with a VDD of 5 V, the VDRIVE pin can be powered from a 3 V supply. The AD7904/AD7914/AD7924 have better dynamic performance with a VDD of 5 V while still being able to interface to 3 V processors. Care should be taken to ensure that VDRIVE does not exceed AVDD by more than 0.3 V (see the Absolute Maximum Ratings section). Reference An external reference source should be used to supply the 2.5 V reference to the AD7904/AD7914/AD7924. Errors in the reference source result in gain errors in the AD7904/AD7914/ AD7924 transfer function and add to the specified full-scale errors of the part. A capacitor of at least 0.1 F should be placed on the REFIN pin. Suitable reference sources for the AD7904/ AD7914/AD7924 include the AD780, REF193, and AD1582. If 2.5 V is applied to the REFIN pin, the analog input range can be either 0 V to 2.5 V or 0 V to 5 V, depending on the setting of the RANGE bit in the control register. Rev. B | Page 21 of 32 AD7904/AD7914/AD7924 MODES OF OPERATION The AD7904/AD7914/AD7924 have three modes of operation. These modes are designed to provide flexible power management options. These options can be chosen to optimize the power dissipation/throughput rate ratio for differing application requirements. The mode of operation of the AD7904/AD7914/AD7924 is controlled by the power management bits, PM1 and PM0, in the control register (see Table 9). When power supplies are first applied to the AD7904/AD7914/AD7924, care should be taken to ensure that the part is placed in the required mode of operation (see the Powering Up the AD7904/AD7914/AD7924 section). NORMAL MODE (PM1 = PM0 = 1) Normal mode is intended for the fastest throughput rate performance. Because the AD7904/AD7914/AD7924 remain fully powered up at all times, the user does not need to worry about power-up times. Figure 20 shows the general diagram of the operation of the AD7904/AD7914/AD7924 in this mode. 1 12 16 SCLK 2 LEADING ZEROS + 2 CHANNEL IDENTIFIER BITS + CONVERSION RESULT DATA IN TO CONTROL REGISTER NOTES 1. CONTROL REGISTER DATA IS LOADED ON FIRST 12 SCLK CYCLES. 03087-020 DIN In full shutdown mode, all internal circuitry on the AD7904/ AD7914/AD7924 is powered down. The part retains information in the control register during full shutdown. The AD7904/AD7914/ AD7924 remain in full shutdown until the power management bits in the control register, PM1 and PM0, are changed. If a write to the control register occurs while the part is in full shutdown, and the power management bits are changed to PM0 = PM1 = 1 (that is, normal mode), the part will begin to power up on the CS rising edge. The track-and-hold, which was in hold mode while the part was in full shutdown, returns to track mode on the 14th SCLK falling edge. To ensure that the part is fully powered up, tPOWER-UP (t12) should have elapsed before the next CS falling edge. Figure 21 shows the general diagram for this sequence. AUTO SHUTDOWN MODE (PM1 = 0, PM0 = 1) CS DOUT FULL SHUTDOWN MODE (PM1 = 1, PM0 = 0) Figure 20. Normal Mode Operation The conversion is initiated on the falling edge of CS; the trackand-hold enters hold mode as described in the Serial Interface section. The data presented to the AD7904/AD7914/AD7924 on the DIN line during the first 12 clock cycles of the data transfer is loaded into the control register (provided that the WRITE bit is set to 1). In normal mode, the part remains fully powered up at the end of the conversion as long as the PM1 and PM0 bits are set to 1 in the write transfer during that same conversion. To ensure continued operation in normal mode, PM1 and PM0 must both be set to 1 on every data transfer, assuming that a write operation is taking place. If the WRITE bit is set to 0, the power management bits are left unchanged, and the part remains in normal mode. Sixteen serial clock cycles are required to complete the conversion and to access the conversion result. The track-and-hold returns to track mode on the 14th SCLK falling edge. CS may then idle high until the next conversion or it may idle low until some time prior to the next conversion (effectively idling CS low). When a data transfer is complete (DOUT has returned to threestate), another conversion can be initiated after the quiet time, tQUIET, has elapsed by bringing CS low again. In auto shutdown mode, the AD7904/AD7914/AD7924 automatically enter shutdown at the end of each conversion when the control register is updated. When the part is in auto shutdown, the track-and-hold is in hold mode. Figure 22 shows the general diagram of the operation of the AD7904/AD7914/AD7924 in this mode. In auto shutdown mode, all internal circuitry on the AD7904/ AD7914/AD7924 is powered down. The part retains information in the control register during auto shutdown. The AD7904/ AD7914/AD7924 remain in shutdown until the next CS falling edge that it receives. On this CS falling edge, the track-and-hold, which was in hold mode while the part was in shutdown, returns to track mode. Wake-up time from auto shutdown is 1 s maximum, and the user should ensure that 1 s has elapsed before attempting a valid conversion. When running the AD7904/AD7914/AD7924 with a 20 MHz clock, one 16 SCLK dummy cycle should be sufficient to ensure that the part is fully powered up. During this dummy cycle, the contents of the control register should remain unchanged; therefore, the WRITE bit should be set to 0 on the DIN line. This dummy cycle effectively halves the throughput rate of the part, with every other conversion result being valid. In auto shutdown mode, the power consumption of the part is greatly reduced because the part enters shutdown at the end of each conversion. When the control register is programmed to move into auto shutdown mode, it does so at the end of the conversion. The user can move the ADC in and out of the low power state by controlling the CS signal. Rev. B | Page 22 of 32 AD7904/AD7914/AD7924 PART BEGINS TO POWER UP ON CS RISING EDGE AS PM1 = PM0 = 1 PART IS IN FULL SHUTDOWN THE PART IS FULLY POWERED UP ONCE tPOWER UP HAS ELAPSED t12 CS 1 14 16 1 14 16 SCLK DOUT CHANNEL IDENTIFIER BITS + CONVERSION RESULT DATA IN TO CONTROL REGISTER DATA IN TO CONTROL REGISTER CONTROL REGISTER IS LOADED ON THE FIRST 12 CLOCKS. PM1 = 1, PM0 = 1 03087-021 DIN TO KEEP THE PART IN NORMAL MODE, LOAD PM1 = PM0 = 1 IN CONTROL REGISTER Figure 21. Full Shutdown Mode Operation PART ENTERS SHUTDOWN ON CS RISING EDGE AS PM1 = 0, PM0 = 1 PART BEGINS TO POWER UP ON CS FALLING EDGE PART ENTERS SHUTDOWN ON CS RISING EDGE AS PM1 = 0, PM0 = 1 PART IS FULLY POWERED UP DUMMY CONVERSION CS 1 12 16 1 12 16 1 12 16 SCLK DIN INVALID DATA CHANNEL IDENTIFIER BITS + CONVERSION RESULT DATA IN TO CONTROL REGISTER CONTROL REGISTER IS LOADED ON THE FIRST 12 CLOCKS, PM1 = 0, PM0 = 1 CHANNEL IDENTIFIER BITS + CONVERSION RESULT DATA IN TO CONTROL REGISTER CONTROL REGISTER CONTENTS SHOULD NOT CHANGE, WRITE BIT = 0 TO KEEP PART IN THIS MODE, LOAD PM1 = 0, PM0 = 1 IN CONTROL REGISTER OR SET WRITE BIT = 0 Figure 22. Auto Shutdown Mode Operation POWERING UP THE AD7904/AD7914/AD7924 When supplies are first applied to the AD7904/AD7914/AD7924, the ADC may power up in any of the operating modes of the part. To ensure that the part is placed into the required operating mode, the user should perform a dummy cycle operation as shown in Figure 23, Figure 24, and Figure 25. The dummy conversion operation must be performed to place the part into the desired mode of operation. To ensure that the part is in normal mode, this dummy cycle operation can be performed with the DIN line tied high, that is, the PM1 and PM0 bits are set to 11 (depending on other required settings in the control register). However, the minimum power-up time of 1 s must be allowed from the rising edge of CS, where the control register is updated, before attempting the first valid conversion. This power-up time allows for the possibility that the part was initially powered up in shutdown mode. If the desired mode of operation after supplies are applied is auto shutdown mode, two dummy cycles are required: the first dummy cycle with DIN tied high, and the second to set the power management bits, PM1 and PM0, to 01. On the second CS rising edge after the supplies are applied, the control register contains the correct information and the part enters auto shutdown mode as programmed. If power consumption is of critical concern, then in the first dummy cycle, the user can set PM1 and PM0 to 10, that is, full shutdown mode, and then place the part into auto shutdown mode in the second dummy cycle. For illustration purposes, Figure 25 is shown with DIN tied high on the first dummy cycle in this case. Figure 23, Figure 24, and Figure 25 show the required dummy cycles after supplies are applied for normal mode, full shutdown mode, and auto shutdown mode, respectively. If the desired mode of operation is full shutdown, one dummy cycle is required after supplies are applied. In this dummy cycle, the user simply sets the power management bits, PM1 and PM0, to 10 and, upon the rising edge of CS at the end of that serial transfer, the part enters full shutdown mode. Rev. B | Page 23 of 32 03087-022 DOUT AD7904/AD7914/AD7924 IF IN SHUTDOWN AT POWER-ON, PART BEGINS TO POWER UP ON CS RISING EDGE AS PM1 = PM0 = 1 PART IS IN UNKNOWN MODE AFTER POWER-ON ALLOW tPOWER TO ELAPSE t12 CS 1 14 16 1 14 16 SCLK DOUT INVALID DATA CHANNEL IDENTIFIER BITS + CONVERSION RESULT DIN 03087-023 DATA IN TO CONTROL REGISTER DIN LINE HIGH FOR FIRST DUMMY CONVERSION TO KEEP THE PART IN NORMAL MODE, LOAD PM1 = PM0 = 1 IN CONTROL REGISTER Figure 23. Placing the AD7904/AD7914/AD7924 into Normal Mode After Supplies Are First Applied PART IS IN UNKNOWN MODE AFTER POWER-ON PART ENTERS SHUTDOWN ON CS RISING EDGE AS PM1 = 1, PM0 = 0 CS 1 14 16 SCLK INVALID DATA DOUT DATA IN TO CONTROL REGISTER 03087-024 DIN CONTROL REGISTER IS LOADED ON THE FIRST 12 CLOCKS. PM1 = 1, PM0 = 0 Figure 24. Placing the AD7904/AD7914/AD7924 into Full Shutdown Mode After Supplies Are First Applied PART IS IN UNKNOWN MODE AFTER POWER-ON PART ENTERS AUTO SHUTDOWN ON CS RISING EDGE AS PM1 = 0, PM0 = 1 CS 1 14 16 1 14 16 SCLK INVALID DATA INVALID DATA DIN DATA IN TO CONTROL REGISTER DIN LINE HIGH FOR FIRST DUMMY CONVERSION CONTROL REGISTER IS LOADED ON THE FIRST 12 CLOCKS. PM1 = 0, PM0 = 1 Figure 25. Placing the AD7904/AD7914/AD7924 into Auto Shutdown Mode After Supplies Are First Applied Rev. B | Page 24 of 32 03087-025 DOUT AD7904/AD7914/AD7924 POWER vs. THROUGHPUT RATE By operating the AD7904/AD7914/AD7924 in auto shutdown mode, the average power consumption of the ADC decreases at lower throughput rates. Figure 26 shows how, as the throughput rate is reduced, the part remains in its shutdown state longer, and the average power consumption over time drops accordingly. For example, if the AD7924 is operated in continuous sampling mode with a throughput rate of 100 kSPS and an SCLK of 20 MHz (AVDD = 5 V), and the device is placed into auto shutdown mode (PM1 = 0 and PM0 = 1), the power consumption is calculated as described in this section. The maximum power dissipation during normal operation is 13.5 mW (AVDD = 5 V). If the power-up time from auto shutdown is one dummy cycle, that is, 1 s, and the remaining conversion time is another cycle, that is, 1 s, then the AD7924 can be said to dissipate 13.5 mW for 2 s during each conversion cycle. For the remainder of the conversion cycle, 8 s, the part remains in shutdown. The AD7924 can be said to dissipate 2.5 W for the remaining 8 s of the conversion cycle. If the throughput rate is 100 kSPS, the cycle time is 10 s and the average power dissipated during each cycle is ((2/10) x 13.5 mW) + ((8/10) x 2.5 W) = 2.702 mW. Figure 26 shows the maximum power vs. throughput rate when using the auto shutdown mode with 5 V and 3 V supplies. 10 AVDD = 5V AVDD = 3V POWER (mW) 1 Sixteen serial clock cycles are required to perform the conversion process and to access data from the AD7904/AD7914/AD7924. For the AD7904/AD7914/AD7924, the 8/10/12 bits of data are preceded by two leading zeros and the two channel address bits, ADD1 and ADD0, which identify the channel that the result corresponds to. CS going low clocks out the first leading zero to be read in by the microcontroller or DSP on the first falling edge of SCLK. The first falling edge of SCLK also clocks out the second leading zero to be read in by the microcontroller or DSP on the second SCLK falling edge, and so on. The two address bits and the 8/10/12 data bits are then clocked out by subsequent SCLK falling edges beginning with the first address bit, ADD1; thus, the second falling clock edge on the serial clock has the second leading zero provided and also clocks out the address bit ADD1. The final bit in the data transfer is valid on the 16th falling edge, having been clocked out on the previous (15th) falling edge. The writing of information to the control register takes place on the first 12 falling edges of SCLK in a data transfer, assuming that the MSB (the WRITE bit) has been set to 1. 0 50 100 150 200 250 300 THROUGHPUT (kSPS) 350 03087-026 0.1 0.01 The CS signal initiates the data transfer and conversion process. The falling edge of CS puts the track-and-hold into hold mode and takes the bus out of three-state; the analog input is sampled at this point. The conversion is also initiated at this point and requires 16 SCLK cycles to complete. The track-and-hold returns to track mode on the 14th SCLK falling edge, as shown by Point B in Figure 27, Figure 28, and Figure 29. On the 16th SCLK falling edge, the DOUT line returns to three-state. If the rising edge of CS occurs before 16 SCLKs have elapsed, the conversion is terminated, the DOUT line returns to three-state, and the control register is not updated; otherwise, DOUT returns to three-state on the 16th SCLK falling edge, as shown in Figure 27, Figure 28, and Figure 29. Figure 26. AD7924 Power vs. Throughput Rate SERIAL INTERFACE Figure 27, Figure 28, and Figure 29 show the detailed timing diagrams for serial interfacing to the AD7904, AD7914, and AD7924, respectively. The serial clock provides the conversion clock and controls the transfer of information to and from the AD7904/AD7914/AD7924 during each conversion. The AD7904 outputs two leading zeros, two channel address bits that the conversion result corresponds to, followed by the 8-bit conversion result and four trailing zeros. The AD7914 outputs two leading zeros, two channel address bits that the conversion result corresponds to, followed by the 10-bit conversion result and two trailing zeros. The 16-bit word read from the AD7924 always contains two leading zeros, two channel address bits that the conversion result corresponds to, followed by the 12-bit conversion result. Rev. B | Page 25 of 32 AD7904/AD7914/AD7924 CS 1 SCLK 2 3 4 t3 DOUT 5 ZERO t9 WRITE ADD1 6 ADD0 DB7 DONTC 12 13 14 15 16 t5 t11 t8 DB0 DB6 2 IDENTIFICATION BITS SEQ1 B 11 t7 t4 THREESTATE ZERO DIN tCONVERT t6 ZERO ZERO ZERO ZERO 4 TRAILING ZEROS t10 DONTC ADD1 ADD0 CODING DONTC DONTC DONTC tQUIET THREESTATE 03087-027 t2 DONTC Figure 27. AD7904 Serial Interface Timing Diagram CS 1 SCLK 2 3 4 t3 DOUT 5 ZERO t9 WRITE ADD1 6 ADD0 DB9 DONTC 12 13 14 15 16 t5 t11 t8 DB2 DB8 2 IDENTIFICATION BITS SEQ1 B 11 t7 t4 THREESTATE ZERO DIN tCONVERT t6 DB1 DB0 ZERO ZERO 2 TRAILING ZEROS t10 DONTC ADD1 ADD0 CODING DONTC DONTC DONTC tQUIET THREESTATE 03087-028 t2 DONTC Figure 28. AD7914 Serial Interface Timing Diagram CS 1 SCLK 2 3 4 t3 DOUT DIN tCONVERT t6 5 ZERO WRITE t9 ADD1 ADD0 DB11 2 IDENTIFICATION BITS SEQ1 DONTC B 11 12 13 14 15 ADD1 t11 t8 DB10 DB4 DB3 DB2 DB1 t10 DONTC 16 t5 t7 t4 THREESTATE ZERO 6 ADD0 CODING DONTC DONTC Figure 29. AD7924 Serial Interface Timing Diagram Rev. B | Page 26 of 32 DONTC DB0 tQUIET THREESTATE DONTC 03087-029 t2 AD7904/AD7914/AD7924 APPLICATIONS INFORMATION The SPORT0 control register of the ADSP-218x should be set up as follows: MICROPROCESSOR INTERFACING The serial interface of the AD7904/AD7914/AD7924 allows the part to be directly connected to a range of different microprocessors. This section explains how to interface the AD7904/AD7914/AD7924 to some of the more common microcontroller and DSP serial interface protocols. AD7904/AD7914/AD7924 to TMS320C541 The serial interface of the TMS320C541 uses a continuous serial clock and frame synchronization signals to synchronize the data transfer operations with peripheral devices such as the AD7904/ AD7914/AD7924. The CS input allows easy interfacing between the TMS320C541 and the AD7904/AD7914/AD7924 without any glue logic required. The serial port of the TMS320C541 is set up to operate in burst mode with internal CLKX0 (TX serial clock on Serial Port 0) and FSX0 (TX frame sync from Serial Port 0). The serial port control (SPC) register must have the following setup: FO = 0, FSM = 1, MCM = 1, and TXM = 1. The connection diagram is shown in Figure 30. Note that for signal processing applications, it is imperative that the frame synchronization signal from the TMS320C541 provide equidistant sampling. The VDRIVE pin of the AD7904/AD7914/AD7924 takes the same supply voltage as the TMS320C541. This allows the ADC to operate at a higher voltage than the serial interface, that is, the TMS320C541, if necessary. AD7904/ AD7914/ AD7924* SCLK TFSW = RFSW = 1, alternate framing INVRFS = INVTFS = 1, active low frame signal DTYPE = 00, right justify data SLEN = 1111, 16-bit data-words ISCLK = 1, internal serial clock TFSR = RFSR = 1, frame every word IRFS = 0 ITFS = 1 The connection diagram is shown in Figure 31. The ADSP-218x has the TFS and RFS of the SPORT tied together, with TFS set as an output and RFS set as an input. The DSP operates in alternate framing mode and the SPORT0 control register is set up as described. The frame synchronization signal generated on the TFS is tied to CS and, as with all signal processing applications, equidistant sampling is necessary. However, in this example, the timer interrupt is used to control the sampling rate of the ADC, and under certain conditions equidistant sampling may not be achieved. AD7904/ AD7914/ AD7924* ADSP-218x* SCLK SCLK DOUT DR CS TMS320C541* RFS TFS DIN DT VDRIVE CLKX DR DIN DT VDRIVE VDD *ADDITIONAL PINS REMOVED FOR CLARITY. FSX FSR Figure 31. Interfacing to the ADSP-218x VDD *ADDITIONAL PINS REMOVED FOR CLARITY. 03087-030 CS 03087-031 CLKR DOUT Figure 30. Interfacing to the TMS320C541 AD7904/AD7914/AD7924 to ADSP-218x The ADSP-218x family of DSPs interfaces directly to the AD7904/AD7914/AD7924 without any glue logic required. The VDRIVE pin of the AD7904/AD7914/AD7924 takes the same supply voltage as the ADSP-218x. This allows the ADC to operate at a higher voltage than the serial interface, that is, the ADSP-218x, if necessary. The timer register, for example, is loaded with a value that provides an interrupt at the required sample interval. When an interrupt is received, a value is transmitted with TFS/DT (ADC control word). The TFS is used to control the RFS and thus the reading of data. The frequency of the serial clock is set in the SCLKDIV register. When the instruction to transmit with TFS is given (that is, AX0 = TX0), the state of the SCLK is checked. The DSP waits until SCLK goes high, low, and high again before transmission starts. If the timer and SCLK values are chosen in such a way that the instruction to transmit occurs on or near the rising edge of SCLK, the data may be transmitted or it may wait until the next clock edge. For example, if the ADSP-2189 has a 20 MHz crystal so that its master clock frequency is 40 MHz, then the master cycle time is 25 ns. If the SCLKDIV register is loaded with the value 3, then an SCLK of 5 MHz is obtained and eight master clock periods elapse for every one SCLK period. Rev. B | Page 27 of 32 AD7904/AD7914/AD7924 Depending on the throughput rate selected, if the timer register is loaded with a value such as 803 (803 + 1 = 804), then 100.5 SCLKs will occur between interrupts and subsequently between transmit instructions. This setup results in nonequidistant sampling because the transmit instruction occurs on an SCLK edge. If the number of SCLKs between interrupts is a whole integer value N, equidistant sampling is implemented by the DSP. AD7904/AD7914/AD7924 to DSP563xx The connection diagram in Figure 32 shows how the AD7904/ AD7914/AD7924 can be connected to the ESSI (synchronous serial interface) of the DSP563xx family of DSPs from Motorola. Each ESSI (two on board) is operated in synchronous mode (SYN bit in CRB = 1) with internally generated 1-bit clock period frame sync for both Tx and Rx (bits FSL1 = 0 and FSL0 = 0 in CRB). Normal operation of the ESSI is selected by setting MOD = 0 in the CRB. Set the word length to 16 by setting bits WL1 = 1 and WL0 = 0 in CRA. The FSP bit in the CRB should be set to 1 so that the frame sync is negative. Note that for signal processing applications, it is imperative that the frame synchronization signal from the DSP563xx provide equidistant sampling. In the example shown in Figure 32, the serial clock is taken from the ESSI so the SCK0 pin must be set as an output (SCKD = 1). The VDRIVE pin of the AD7904/AD7914/AD7924 takes the same supply voltage as the DSP563xx. This allows the ADC to operate at a higher voltage than the serial interface, that is, the DSP563xx, if necessary. AD7904/ AD7914/ AD7924* DSP563xx* SCLK SCK DOUT SRD CS STD DIN SC2 VDD *ADDITIONAL PINS REMOVED FOR CLARITY. Figure 32. Interfacing to the DSP563xx 03087-032 VDRIVE GROUNDING AND LAYOUT The AD7904/AD7914/AD7924 have very good immunity to noise on the power supplies (see Figure 6). However, care should be taken with regard to grounding and layout. The PCB that houses the AD7904/AD7914/AD7924 should be designed such that the analog and digital sections are separated and confined to certain areas of the board. This facilitates the use of ground planes that can be easily separated. A minimum etch technique is generally best for ground planes because it provides the best shielding. All four AGND pins of the AD7904/ AD7914/AD7924 should be sunk in the AGND plane. Digital and analog ground planes should be joined at only one place. If the AD7904/AD7914/AD7924 are in a system where multiple devices require an AGND-to-DGND connection, the connection should still be made at one point only: a star ground point established as close as possible to the AD7904/AD7914/AD7924. Avoid running digital lines under the device because these lines couple noise onto the die. The analog ground plane should be allowed to run under the AD7904/AD7914/AD7924 to avoid noise coupling. The power supply lines to the AD7904/AD7914/ AD7924 should use as large a trace as possible to provide low impedance paths and reduce the effects of glitches on the power supply line. Fast switching signals such as clocks should be shielded with digital ground to avoid radiating noise to other sections of the board, and clock signals should never be run near the analog inputs. Avoid crossover of digital and analog signals. Traces on opposite sides of the board should run at right angles to each other to reduce the effects of feedthrough through the board. A microstrip technique is by far the best, but is not always possible with a double-sided board. In this technique, the component side of the board is dedicated to ground planes while signals are placed on the solder side. Good decoupling is also important. All analog supplies should be decoupled with 10 F tantalum capacitors in parallel with 0.1 F capacitors to AGND. To achieve the best performance from these decoupling components, place them as close as possible to the device, ideally right up against the device. The 0.1 F capacitors should have low effective series resistance (ESR) and effective series inductance (ESI), such as the common ceramic types or surface-mount types, which provide a low impedance path to ground at high frequencies to handle transient currents due to internal logic switching. Rev. B | Page 28 of 32 AD7904/AD7914/AD7924 EVALUATING AD7904/AD7914/AD7924 PERFORMANCE The recommended layout for the AD7904/AD7914/AD7924 is outlined in the evaluation board for the AD7904/AD7914/ AD7924. The evaluation board package includes a fully assembled and tested evaluation board, documentation, and software for controlling the board from a PC via the evaluation board controller (EVAL-CONTROL-BRD2). The evaluation board controller can be used in conjunction with the AD7904/AD7914/AD7924 evaluation board, as well as with many other Analog Devices, Inc., evaluation boards ending in the CB designator, to demonstrate and evaluate the ac and dc performance of the AD7904/AD7914/AD7924. The software allows the user to perform ac (fast Fourier transform) and dc (histogram of codes) tests on the AD7904/ AD7914/AD7924. The software and documentation are on a CD shipped with the evaluation board. Rev. B | Page 29 of 32 AD7904/AD7914/AD7924 OUTLINE DIMENSIONS 5.10 5.00 4.90 16 9 4.50 4.40 4.30 6.40 BSC 1 8 PIN 1 1.20 MAX 0.15 0.05 0.65 BSC 0.30 0.19 COPLANARITY 0.10 0.20 0.09 SEATING PLANE 0.75 0.60 0.45 8 0 COMPLIANT TO JEDEC STANDARDS MO-153-AB Figure 33. 16-Lead Thin Shrink Small Outline Package (TSSOP) (RU-16) Dimensions shown in millimeters ORDERING GUIDE Model 1, 2 AD7904BRU AD7904BRU-REEL AD7904BRUZ AD7904BRUZ-REEL AD7904BRUZ-REEL7 AD7904WYRUZ-REEL7 AD7914BRU-REEL AD7914BRUZ AD7914BRUZ-REEL7 AD7914WYRUZ-REEL7 AD7924BRU AD7924BRU-REEL7 AD7924BRUZ AD7924BRUZ-REEL AD7924BRUZ-REEL7 AD7924WYRUZ-REEL7 EVAL-AD79x4CBZ EVAL-CONTROL-BRD2 Notes Temperature Range -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +125C -40C to +85C -40C to +85C -40C to +85C -40C to +125C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +125C Linearity Error (LSB) 3 0.2 0.2 0.2 0.2 0.2 0.2 0.5 0.5 0.5 0.5 1 1 1 1 1 1 4 5 Package Option RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 RU-16 Package Description 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP Evaluation Board Controller Board 1 Z = RoHS Compliant Part. W = Qualified for Automotive Applications. Linearity error refers to integral linearity error. 4 This board can be used as a standalone evaluation board or in conjunction with the Evaluation Controller Board for evaluation/demonstration purposes. The board comes with one chip each of the AD7904, AD7914, and AD7924. 5 This board is a complete unit, allowing a PC to control and communicate with all Analog Devices evaluation boards ending in the CB designator. To order a complete evaluation kit, you need to order the specific ADC evaluation board, for example, the EVAL-AD79x4CBZ, the EVAL-CONTROL-BRD2, and a 12 V ac transformer. See the relevant Evaluation Board Technical Note for more information. 2 3 AUTOMOTIVE PRODUCTS The AD7904W/AD7914W/AD7924W models are available with controlled manufacturing to support the quality and reliability requirements of automotive applications. Note that these automotive models may have specifications that differ from the commercial models; therefore, designers should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for use in automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to obtain the specific Automotive Reliability reports for these models. Rev. B | Page 30 of 32 AD7904/AD7914/AD7924 NOTES Rev. B | Page 31 of 32 AD7904/AD7914/AD7924 NOTES (c)2002-2011 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D03087-0-7/11(B) Rev. B | Page 32 of 32