EClamp2122S USB Downstream Port Filter & TVS For EMI Filtering and ESD Protection PROTECTION PRODUCTS - EMIClamp(R) Description Features The EClamp 2122S is combination EMI filter and line termination device with integrated TVS diodes for use on USB interfaces. This device utilizes solid-state silicon-avalanche technology for superior clamping performance and DC electrical characteristics. They have been optimized for protection of USB interfaces in cellular phones and other portable electronics. USB line termination is achieved with a series 22 resistor on both the D+ and D- USB lines. These resistors preserve signal integrity by matching the cable impedance to that of the differential driver. The 15k pull-down resistors complete the termination circuit on each line. They are required by the USB specification to identify the line as a downstream connection. The capacitors are used to bypass high frequency energy to ground and for edge rate control of the USB signals. Integrated TVS diodes provide ESD protection of both (D+ & D-) data lines and the voltage bus (VBUS). The TVS diodes provide effective suppression of ESD voltages in excess of 25kV (air discharge) and 20kV (contact discharge) per IEC 61000-4-2. The EClamp2122S is in a 6-pin SOT-23 package. The leads are finished with lead-free matte tin. It is suitable for use in USB hubs, computers, peripherals, and portable devices (R) EMI/RFI filtering and line termination with inte grated ESD protection ESD protection for USB power (VBUS) and data lines (D+ & D-) to IEC 61000-4-2 (ESD), 25kV (air), 20kV (contact) Filtering and termination for two USB data lines Series resistors for impedance matching Integrated pull down resistors as required by the USB specification for downstream ports Low TVS operating voltage (5.25V) Solid-state technology Mechanical Characteristics JEDEC SOT-23 6L package Pb-Free, Halogen Free, RoHS/WEEE Compliant Nominal Dimensions: 2.9 x 2.8mm Molding compound flammability rating: UL 94V-0 Marking: Marking Code + Date Code Packaging: Tape and Reel Applications Circuit Diagram USB 1.1 Interfaces USB Hubs Printers Monitors Servers, Desktop, and Notebook computers Pin Configuration C1 C2 C1 C2 (Top Side View) Revision 5/26/2011 1 www.semtech.com EClamp2122S PROTECTION PRODUCTS Absolute Maximum Rating R ating Symbol Value Units Steady-State Power PSS 100 mW ESD Air Discharge per IEC 61000-4-2 ESD Contact Discharge per IEC 61000-4-2 VESD 25 20 kV Lead Soldering Temperature TL 260 (10 sec.) C Operating Temperature TJ -40 to +125 C TSTG -55 to +150 C Storage Temperature Electrical Characteristics (T = 25oC) Parameter Symbol Conditions Minimum T VS Reverse Stand-Off Voltage VRWM T VS Reverse Breakdown Voltage V BR It = 1mA T VS Reverse Leakage Current IR VRWM = 5.25V, T=25C Pi n 1 to 6 Series Resistance RS Each Line 20 Pulldown Resistance R PD Each Line 13.5 Clamping Voltage VC IPP = 3A, tp = 8/20s Pin 2 or Pin 3 to Pin 6 T VS Diode Capacitance C Each Line VR = 0V, f = 1MHz CTOT Between Input or Output to Ground VR = 0V, f = 1MHz Total Capacitance (c) 2011 Semtech Corp. 2 Typical Maximum Units 5.25 V 6 27 V 5 A 22 24 15 16.5 k 11 V 33 pF 30 50 pF www.semtech.com EClamp2122S PROTECTION PRODUCTS Typical Characteristics ESD Clamping (Pin 1 to GND) (8kV Contact per IEC 61000-4-2) ESD Clamping (Pin 1 to GND) (-8kV Contact per IEC 61000-4-2) ESD Clamping (Pin 4 or 5 to GND) (8kV Contact per IEC 61000-4-2) ESD Clamping (Pin 4 or 5 to GND) (-8kV Contact per IEC 61000-4-2) Note: ESD data is taken with a 20dB attenuator (c) 2011 Semtech Corp. 3 www.semtech.com EClamp2122S PROTECTION PRODUCTS Typical Insertion Loss S21 (Pin 2 to 5 with respect to GND) Frequency 114.9MHz 800MHz 900MHz 1.8GHz 2.5GHz 2.7GHz Typical Insertion Loss S21 (Pin 3 to 4 with respect to GND) S21 (dB) -3.00 -14.11 -11.62 -5.16 -3.55 -3.52 Frequency S21 (dB) 114.6MHz -3.00 800MHz -12.58 900MHz -10.40 1.8GHz -4.76 2.5GHz -3.30 2.7GHz -3.38 Clamping Voltage vs. Peak Pulse Current (Between any I/O and Ground) 10 1.5 1.4 1.3 1.2 1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 9 Clamping Voltage - VC (V) CJ(VR) / CJ(VR=0) Normalized Junction Capacitance vs. Reverse Voltage (Data Pins) 8 7 6 5 4 3 Waveform Parameters: tr = 8s td = 20s 2 1 f = 1 MHz 0 1 (c) 2011 Semtech Corp. 2 3 Reverse Voltage - VR (V) 4 0 0 5 4 0.5 1 1.5 2 2.5 Peak Pulse Current - IPP (A) 3 3.5 www.semtech.com EClamp2122S PROTECTION PRODUCTS Applications Information Figure 1 - EClam p2 122S Cir cuit Diagram EClamp2 p2122S Circuit Device Connection The EClamp2122S is designed to provide termination, EMI filtering and ESD protection for two USB I/O lines. The equivalent circuit diagram is shown in Figure 1. The device is connected as follows: z USB data lines are routed through the EClamp2122S for easy implementation and optimum pc board layout. Pin 1 is connected to the voltage supply line. The input of the D+ line is routed into pin 2 and out of pin 5. The input of the D- line is connected at pin 3 and the output at pin 4. Pin 6 is connected to ground. The ground connection should be made directly to the ground plane for best results. The path length is kept as short as possible to reduce the effects of parasitic inductance in the board traces. C1 C2 C1 C2 USB Port Design with EClamp2122S The Universal Serial Bus (USB) specification requires termination and filtering components for proper operation. In addition, an open USB socket is vulnerable to hazardous ESD discharges in excess of 15kV. These discharges can occur on the data lines or the voltage bus. The EClamp2122S is an easily implemented solution designed to meet the termination & EMI filter requirements of the USB specification revision 1.1. It also provides ESD protection to IEC 61000-4-2. USB line termination is achieved with series resistors on both the D+ and D- lines. These resistors preserve signal integrity by matching the cable impedance to that of the differential driver. 15k pull-down resistors are used to identify a downstream port. Capacitors are used to bypass high frequency energy to ground and for edge rate control of the USB signals. Integrated TVS diodes provide ESD protection of both (D+ & D-) data lines and the voltage bus (VBUS). General layout guidelines are given below: z z z z Avoid running D+ & D- signal line traces near high speed clock lines or similar signal lines. Avoid running critical signal lines near board edges. Place the EClamp2122S near the USB connector to restrict transient coupling. Minimize the path length between the USB connector and the EClamp2122S. (c) 2011 Semtech Corp. 5 www.semtech.com EClamp2122S PROTECTION PRODUCTS Outline Drawing - SOT-23 6L DIM A e1 2X E/2 A A1 A2 b c D E1 E e e1 L L1 N 01 aaa bbb ccc D N EI 1 E 2 ccc C 2X N/2 TIPS e B D aaa C A2 SEATING PLANE DIMENSIONS INCHES MILLIMETERS MIN NOM MAX MIN NOM MAX .057 .035 .000 .006 .035 .045 .051 .010 .020 .003 .009 .110 .114 .122 .060 .063 .069 .110 BSC .037 BSC .075 BSC .012 .018 .024 (.024) 6 0 10 .004 .008 .008 A H A1 C bxN bbb 0.90 1.45 0.00 0.15 .90 1.15 1.30 0.25 0.50 0.08 0.22 2.80 2.90 3.10 1.50 1.60 1.75 2.80 BSC 0.95 BSC 1.90 BSC 0.30 0.45 0.60 (0.60) 6 0 10 0.10 0.20 0.20 C A-B D c GAGE PLANE 0.25 L 01 (L1) SEE DETAIL DETAIL A A SIDE VIEW NOTES: 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). 2. DATUMS -A- AND -B- TO BE DETERMINED AT DATUM PLANE -H3. DIMENSIONS "E1" AND "D" DO NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. Land Pattern - SOT-23 6L X DIM (C) G Z Y P C G P X Y Z DIMENSIONS MILLIMETERS INCHES (.098) .055 .037 .024 .043 .141 (2.50) 1.40 0.95 0.60 1.10 3.60 NOTES: 1. (c) 2011 Semtech Corp. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY. CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR COMPANY'S MANUFACTURING GUIDELINES ARE MET. 6 www.semtech.com EClamp2122S PROTECTION PRODUCTS Marking YW 212 Ordering Information Part Number Qty per Reel Reel Size EClamp 2122S.TCT 3,000 7 Inch Note: Lead finish is lead-free matte tin EMIClamp and EClamp are trademarks of Semtech Corporation YW = 2 - Alphanumeric characters for Date Code Tape and Reel Specification User Direction of feed Device Orientation in Tape A0 3.23 +/-0.05 mm B0 K0 3.17 +/-0.05 mm Tape Width B, (Max) D 8 mm 4.2 mm (.165) 1.5 + 0.1 mm - 0.0 mm 1.37 +/-0.05 mm D1 E 1.0 mm 0.05 1.750.10 mm F K (MAX) P P0 P2 T(MAX) 3.50.05 mm 2.4 mm 4.00.1 mm 4.00.1 mm 2.00.05 mm 0.4 mm W 8.0 mm + 0.3 mm - 0.1 mm Contact Information for Semtech International AG Taiw an Branch Tel: 886-2-2748-3380 Fax: 886-2-2748-3390 Semtech Sw itz erland GmbH Japan Branch Tel: 81-3-6408-0950 Fax: 81-3-6408-0951 Tel: 82-2-527-4377 Fax: 82-2-527-4376 Semtech Limited (U.K.) Tel: 44-1794-527-600 Fax: 44-1794-527-601 Tel: 86-21-6391-0830 Fax: 86-21-6391-0831 Semtech France SARL Tel: 33-(0)169-28-22-00 Fax: 33-(0)169-28-12-98 Semtech International AG is a wholly-owned subsidiary of Semtech Corporation, which has its headquarters in the U.S.A. Semtech Germany GmbH Tel: 49-(0)8161-140-123 Fax: 49-(0)8161-140-124 (c) 2011 Semtech Corp. 7 Korea Branch Shanghai Office www.semtech.com