General Description
The MAX9060–MAX9064 are small single comparators,
ideal for a wide variety of portable electronics applications
such as cell phones, media players, and notebooks that
have extremely tight board space and power constraints.
These comparators are offered in both, a miniature
4-bump UCSP™ package with a 1mm x 1mm footprint (as
small as two 0402 resistors), and a 5-pin SOT23 package.
The MAX9060–MAX9064 feature an input voltage range
of -0.3V to +5.5V independent of supply voltage. These
devices maintain high impedance at the inputs even when
powered down (VCC or VREF = 0V). They also feature
internal filtering to provide high RF immunity.
The MAX9060 and MAX9061 have open-drain outputs and
draw quiescent supply current from a user-supplied refer-
ence voltage, VREF, between 0.9V and 5.5V. These devic-
es consume only 100nA (max) supply current and operate
over the extended -40°C to +85°C temperature range.
The MAX9062, MAX9063 and MAX9064 are single com-
parators with an internal 0.2V reference. These devices
feature either a push-pull or an open-drain output. They
consume only 700nA (max) supply current. The MAX9062,
MAX9063, and MAX9064 operate down to VCC = 1V over
the extended -40°C to +85°C temperature range.
Applications
●Cell Phones
●Portable Media Players
●Electronic Toys
●Notebook Computers
●Portable Medical Devices
Features
●Tiny 1mm x 1mm x 0.6mm 4-Bump UCSP
●Footprint = Two 0402 Resistors
●Also Available in a 5-Pin SOT23 Package
●Ultra-Low Operating Current (100nA max)
●Input Voltage Range = -0.3V to +5.5V
●External REF Range = 0.9V to 5.5V
(MAX9060/MAX9061)
●Internal REF Voltage = 0.2V
(MAX9062/MAX9063/MAX9064)
● 15μs Propagation Delay
●-40°C to +85°C Extended Temperature Range
Selector Guide and Typical Operating Circuits appears at
end of data sheet.
Note: All devices are specified over the extended -40°C
to+85°C operating temperature range.
+Denotes a lead(Pb)-free/RoHS-compliant package.
/V denotes an automotive qualified device.
T = Tape and reel.
G45 = Protective die coating.
UCSP is a trademark of Maxim Integrated Products, Inc.
PART PIN PACKAGE TOP MARK
MAX9060EBS+G45 4 UCSP AFX
MAX9060EUK+ 5 SOT23 AFFG
MAX9061EBS+G45 4 UCSP AFY
MAX9061EUK+ 5 SOT23 AFFH
MAX9062EBS+G45 4 UCSP AFZ
MAX9062EUK+ 5 SOT23 AFFI
MAX9063EBS+G45 4 UCSP AGA
MAX9063EUK+ 5 SOT23 AFFJ
MAX9063EUK/V+T 5 SOT23 +AMGH
MAX9064EBS+G45 4 UCSP AGB
MAX9064EUK+ 5 SOT23 AFFK
MAX9060–MAX9064
MAX9060–
MAX9064
A1
UCSP SOT23
REF = MAX9060/MAX9061
(VCC) = MAX9062–MAX9064
TOP VIEW (BUMPS ON BOTTOM)
A2
B1 B2
IN
GND
OUT
REF
(VCC)
1
+
3
2
5
4
REF
(VCC)
GND
OUT
IN
GND
MAX9060–MAX9064 Ultra-Small, nanoPower Single
Comparators in 4-Bump UCSP and 5 SOT23
19-4105; Rev 7; 3/17
Ordering Information
Pin Congurations
EVALUATION KIT AVAILABLE
VCC, REF, IN to GND .............................................. -0.3V to +6V
OUT to GND (MAX9060–MAX9063) ....................... -0.3V to +6V
OUT to GND (MAX9064 Only) ..............-0.3V to + (VCC + 0.3V)
Output Short-Circuit Current Duration ................................... 10s
Input Current into Any Terminal ........................................±20mA
Continuous Power Dissipation
4-Bump UCSP (derate 3.0mW/°C above +70°C) ........238mW
5-Pin SOT23 (derate 3.9mW/°C above +70°C) .......... 312mW
Operating Temperature Range ............................ -40°C to +85°C
Junction Temperature ...................................................... +150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (excluding UCSP, soldering, 10s) ..... +300°C
Soldering Temperature (reflow) ....................................... +260°C
(VREF = 1.8V, RPULLUP = 10kΩ to VPULLUP = 3.3V, TA = -40°C to +85°C. Typical values are at TA = +25°C, unless otherwise noted.)
(Note 1)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
DC CHARACTERISTICS
Input Offset Voltage (Note 2) VOS
TA = +25°C 1.3 6 mV
9
Hysteresis VHYS (Note 3) ±12 mV
Input Voltage Range VIN -0.3 +5.5 V
Input Bias Current IIN
0V < VIN < VREF + 0.6V 40 nA
VREF + 0.6V < VIN < 5.5V 10 100
Input Shutdown Current IIN_PD VREF = 0V, VIN = 5.5V (Note 4) <0.1 27 nA
Output Voltage Low VOL
ISINK = 25µA, VREF = 0.9V, TA = +25°C 0.04 0.20
V
ISINK = 200µA, VREF = 1.2V 0.08 0.20
ISINK = 500µA, VREF = 1.8V 0.13 0.23
ISINK = 1.2mA, VREF = 5.5V 0.19 0.50
Output Leakage Current
(OUT = High) IOUT_LEAKAGE VPULLUP = 5.5V (Note 4) <0.1 35 nA
AC CHARACTERISTICS
Propagation Delay tPD Overdrive = ±100mV (Note 5) 25 µs
Fall Time tFCL = 10pF 14 ns
REF SUPPLY
REF Voltage VREF Guaranteed by VOS tests 0.9 5.5 V
REF Input Current IREF
VREF = 0.9V, VIN = VREF, TA = +25°C 50
nA
VREF = 1.8V, VIN = VREF, TA = +25°C 60
VREF = 5.5V, VIN = VREF, TA = +25°C 170 320
VREF = 5.5V, VIN = VREF, -40°C < TA
< +85°C 350
REF Rejection Ratio RRR VREF = 0.9V to 5.5V, TA = +25°C 63 90 dB
Power-Up Time tON 3 ms
MAX9060–MAX9064 Ultra-Small, nanoPower Single
Comparators in 4-Bump UCSP and 5 SOT23
www.maximintegrated.com Maxim Integrated
│
2
Absolute Maximum Ratings
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
MAX9060/MAX9061 Electrical Characteristics
(VCC = 3.3V, RPULLUP = 10kΩ to VPULLUP = 3.3V for MAX9062/MAX9063, TA = -40°C to +85°C. Typical values at TA = +25°C, unless
otherwise noted.) (Note 1)
Note 1: All devices are 100% production tested at TA = +25°C. Temperature limits are guaranteed by design.
Note 2: Guaranteed by ATE and/or bench characterization over temperature. VOS is the average of the trip points minus VREF.
Note 3: Hysteresis is half the input voltage difference between the two switching points.
Note 4: Too small to be measured in an ATE test environment. Only gross test to catch failures is implemented.
Note 5: Overdrive is defined as the voltage above or below the switching points.
Note 6: Guaranteed by ATE and/or bench characterization over temperature. VREF is the average of the trip points.
Note 7: Includes reference error along with comparator offset voltage error.
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
DC CHARACTERISTICS
Input Voltage Range VIN Guaranteed by IIN test -0.3 +5.5 V
Input Bias Current IIN VIN = 0.2V to 5.5V (Note 4) 0.06 15 nA
Input Leakage Current IIN_SHDN VCC = 0V, VIN = 5.5V (Note 4) <0.1 15 nA
Output Voltage Low VOL
ISINK = 50µA, VCC = 1.0V 0.03 0.2
V
ISINK = 200µA, VCC = 1.2V 0.08 0.20
ISINK = 500µA, VCC = 1.8V 0.13 0.23
ISINK = 0.75mA, VCC = 3.3V 0.14 0.3
ISINK = 1.2mA, VCC = 5.5V 0.19 0.5
Output Voltage High
(MAX9064 Only) VOH
ISOURCE = 15µA, VCC = 1.0V VCC -
0.08V
VCC -
0.02V
V
ISOURCE = 40µA, VCC = 1.2V VCC -
0.08V
VCC -
0.20V
ISOURCE = 180µA, VCC = 1.8V VCC -
0.15V
VCC -
0.23V
ISOURCE = 0.3mA, VCC = 3.3V VCC -
0.13V
VCC -
0.3V
ISOURCE = 0.75mA, VCC = 5.5V VCC -
0.24V
VCC -
0.5V
Output Leakage Current
(MAX9062/MAX9063 Only) IOUT_LEAKAGE OUT = high, VPULLUP = 5.5V (Note 4) <0.1 15 nA
AC CHARACTERISTICS
Propagation Delay tPD VOVERDRIVE = ±100mV (Note 5) 15 µs
Fall Time tFCL = 10pF 14 ns
Rise Time tRCL = 10pF, MAX9064 only 30 ns
REFERENCE VOLTAGE
Input Threshold (Note 6) VREF
TA = +25°C 188 200 212 mV
TA = -40°C to +85°C 185 200 215
Input Threshold Hysteresis VHYS TA = -40°C to +85°C (Note 3) ±0.9 mV
REF Tempco VREF_TEMPCO (Note 7) 6 µV/°C
Power-Supply Rejection Ratio PSRR VCC = 1.0V to 5.5V 40 53 dB
POWER SUPPLY
Supply Voltage VCC Guaranteed by VOL/VOH tests 1.0 5.5 V
Supply Current ICC
VCC = 1.0V 0.4 0.7 µA
VCC = 5.5V 0.6 1.1
Power-Up Time tON 3 ms
MAX9060–MAX9064 Ultra-Small, nanoPower Single
Comparators in 4-Bump UCSP and 5 SOT23
www.maximintegrated.com Maxim Integrated
│
3
MAX9062/MAX9063/MAX9064 Electrical Characteristics
(VCC = 3.3V, VREF = 1.8V, RPULLUP = 10kΩ to VPULLUP = 3.3V for MAX9060–MAX9063, VGND = 0V, TA = +25°C, unless otherwise noted.)
MAX9064 SUPPLY CURRENT
vs. SUPPLY VOLTAGE
MAX9060 toc02
SUPPLY VOLTAGE (V)
SUPPLY CURRENT (nA)
54321
200
400
600
800
1000
0
0 6
+85C
-40C
+25C
MAX9060 SUPPLY CURRENT
vs. OUTPUT TRANSITION FREQUENCY
MAX9060 toc03
OUTPUT TRANSITION FREQUENCY (kHz)
SUPPLY CURRENT (A)
1
0.1
1
10
100
0.01
0.1 10
VREF = 5V
VREF = 3.3V
VREF = 1.8V
MAX9064 SUPPLY CURRENT
vs. OUTPUT TRANSITION FREQUENCY
MAX9060 toc04
OUTPUT TRANSITION FREQUENCY (kHz)
SUPPLY CURRENT (A)
1 10
10
100
1
0.1 100
VCC = 5V
VCC = 3.3V
VCC = 1.8V
MAX9060 AND MAX9064 OUTPUT
VOLTAGE LOW vs. SINK CURRENT
MAX9060 toc05
SINK CURRENT (mA)
OUTPUT VOLTAGE LOW (V)
62
0.5
1.0
0.1
0.6
0.4
0.9
0.3
0.8
0.2
0.7
0
0 4 8
VCC/VREF = 3.3V
VCC/VREF = 1.8V
VCC/VREF = 5V
MAX9064 OUTPUT VOLTAGE HIGH
vs. SOURCE CURRENT
MAX9060 toc06
SOURCE CURRENT (mA)
OIUTPUT VOLTAGE HIGH (VCC - VOH, V)
0.5
1.0
0.1
0.6
0.4
0.9
0.3
0.8
0.2
0.7
0
0 1.51.0 2.5 3.00.5 2.0
VCC = 3.3V
VCC = 1.8V
VCC = 5V
MAX9060 OFFSET VOLTAGE
vs. TEMPERATURE
MAX9060 toc07
TEMPERATURE (C)
OFFSET VOLTAGE (mV)
0.5
1.0
0.1
0.6
0.4
0.9
0.3
0.8
0.2
0.7
0
-40 6035-15 8510
VREF = 1.8V
MAX9060 SUPPLY CURRENT
vs. REF VOLTAGE
MAX9060 toc01
REF VOLTAGE (V)
SUPPLY CURRENT (nA)
54321
50
100
150
200
250
0
0 6
+85C
-40C
+25C
MAX9060 HYSTERESIS VOLTAGE
vs. TEMPERATURE
MAX9060 toc08
TEMPERATURE (C)
HYSTERESIS VOLTAGE (mV)
10
16
2
12
8
6
4
14
0
-40 6035-15 8510
VREF = 1.8V
MAX9060 INPUT BIAS CURRENT
vs. INPUT BIAS VOLTAGE
MAX9060 toc09
INPUT BIAS VOLTAGE (V)
INPUT BIAS CURRENT (nA)
20
30
0
25
15
10
5
-5
-1 10 3 642 5
VREF = 1.8V
MAX9060–MAX9064 Ultra-Small, nanoPower Single
Comparators in 4-Bump UCSP and 5 SOT23
Maxim Integrated
│
4
www.maximintegrated.com
Typical Operating Characteristics
(VCC = 3.3V, VREF = 1.8V, RPULLUP = 10kΩ to VPULLUP = 3.3V for MAX9060–MAX9063, VGND = 0V, TA = +25°C, unless otherwise noted.)
MAX9064 INPUT BIAS CURRENT
vs. INPUT BIAS VOLTAGE
MAX9060 toc10
INPUT BIAS VOLTAGE (V)
INPUT BIAS CURRENT (nA)
-5
5
0
-10
-15
-20
0 0.20 0.25 0.300.05 0.10 0.15
VCC = 3.3V
MAX9064 REFERENCE VOLTAGE
vs. TEMPERATURE
MAX9060 toc11
TEMPERATURE (C)
REFERENCE VOLTAGE (mV)
201.6
202.0
201.8
201.4
201.2
201.0
201.7
201.9
201.5
201.3
201.1
-40 8510 60-15 35
VCC = 3.3V
MAX9064 REFERENCE VOLTAGE
vs. SUPPLY VOLTAGE
MAX9060 toc12
SUPPLY VOLTAGE (V)
REFERENCE VOLTAGE (mV)
200.2
201.0
200.6
199.8
199.4
199.0
200.4
200.8
200.0
199.6
199.2
1.0 5.02.5 3.0 4.54.01.5 2.0 3.5
MAX9064 PROPAGATION DELAY
vs. TEMPERATURE
MAX9060 toc13
TEMPERATURE (C)
PROPAGATION DELAY (s)
14
17
10
15
16
13
12
11
9
-40 -15 60 853510
VCC = 3.3V
VCC = 1.8V
VCC = 5V
VOD = 100mV
MAX9064 PROPAGATION DELAY
vs. INPUT OVERDRIVE
MAX9060 toc14
INPUT OVERDRIVE (mV)
PROPAGATION DELAY (s)
50
80
10
60
40
30
20
70
0
0 100 150 25020050
VCC = 3.3V
VCC = 1.8V
VCC = 5V
MAX9060 PROPAGATION DELAY
vs. INPUT OVERDRIVE
MAX9060 toc15
INPUT OVERDRIVE (mV)
PROPAGATION DELAY (s)
50
80
10
60
40
30
20
70
0
0 100 150 25020050
VREF = 5V
VREF = 1.8V
MAX9060 PROPAGATION DELAY
AT VREF = 1.8V
MAX9060 toc16
100s/div
0V
1.7V
1.9V
IN+
100mV/div
OUT
2V/div
MAX9064 PROPAGATION DELAY
AT VCC = 3.3V
MAX9060 toc17
100s/div
0V
0.1V
0.3V
IN+
100mV/div
OUT
2V/div
MAX9060–MAX9064 Ultra-Small, nanoPower Single
Comparators in 4-Bump UCSP and 5 SOT23
Maxim Integrated
│
5
www.maximintegrated.com
Typical Operating Characteristics (continued)
(VCC = 3.3V, VREF = 1.8V, RPULLUP = 10kΩ to VPULLUP = 3.3V for MAX9060–MAX9063, VGND = 0V, TA = +25°C, unless otherwise noted.)
MAX9064 OUTPUT RESPONSE
TO SUPPLY VOLTAGE TRANSIENT
MAX9060 toc22
1ms/div
0V
0V
0V
3V
3.2V VCC
200mV/div
OUT
2V/div
OUT
2V/div
OUT
2V/div
VIN = VTH + 20mV
VIN = VTH + 10mV
VIN = VTH + 1mV
MAX9060 POWER-UP/
POWER-DOWN RESPONSE
MAX9060 toc20
1ms/div
0V
0V
VREF
1V/div
OUT
2V/div
VIN = 1.7V
VREF = 1.8V
MAX9064 1kHz FREQUENCY RESPONSE
MAX9060 toc18
200s/div
0V
150mV
250mV
IN+
50mV/div
OUT
2V/div
VCC = 3.3V
200mV
MAX9064 POWER-SUPPLY REJECTION
FOR NO FALSE TRIGGERING
MAX9060 toc23
FREQUENCY (Hz)
TRIP POINT (mV)
100k100
200
206
194
202
196
204
198
10 10k1k 1M
VCC = 3.3V + 100mVP-P
UPPER TRIP POINT
LOWER TRIP POINT
MAX9064 POWER-UP/
POWER-DOWN RESPONSE
MAX9060 toc21
1ms/div
0V
0V
VCC
2V/div
OUT
2V/div
VIN = 0.3V
VCC = 3.3V
MAX9060 1kHz FREQUENCY RESPONSE
MAX9060 toc19
200s/div
0V
1.7V
1.9V
1.8V
IN+
100mV/div
OUT
2V/div
VREF = 1.8V
VPULLUP = 3.3V
MAX9060–MAX9064 Ultra-Small, nanoPower Single
Comparators in 4-Bump UCSP and 5 SOT23
Maxim Integrated
│
6
www.maximintegrated.com
Typical Operating Characteristics (continued)
Detailed Description
The MAX9060–MAX9064 are extremely small com-
parators ideal for compact, low-current, and lowvoltage
applications.
The MAX9060/MAX9061 consume only 50nA (typ) oper-
ating current, while the MAX9062/MAX9063/MAX9064
consume only 400nA (typ). The low-voltage operat-
ing capability of the MAX9060–MAX9064 makes these
devices extremely attractive to long-life battery-operated
devices—these applications can now use a single digital
power-supply rail to power the new generation of micro-
controllers (which can be down to 0.9V). A single AA/AAA
cell can drop down to 0.9V in full discharge. All parts are
available in a tiny 4-bump UCSP, that is only 0.6mm tall,
and occupies a 1mm x 1mm footprint and a 5-pin SOT23.
Input Stage Circuitry
Noninverting inputs are available on the MAX9060/
MAX9062/MAX9064 and inverting inputs are available on
the MAX9061/MAX9063.
The MAX9060–MAX9064 incorporate an innovative
input stage architecture that allows their input voltage
to exceed VCC by several volts (limited only by the
Absolute Maximum Ratings). This is unlike tradition-
al comparators that have an input ESD diode clamp
between the input and VCC, limiting this maximum over-
voltage to about 0.3V. The MAX9060–MAX9064 archi-
tecture maintains a high input impedance to input signals
even when the device power-supply voltage is completely
turned off (VCC or REF taken to 0V). This greatly benefits
flexible power-saving schemes to be easily implemented
in advanced battery-operated devices. On-chip filtering
provides immunity from any RF noise being picked up by
input traces. These devices feature an internal temper-
ature-compensated, low-power 0.2V reference voltage.
Output Stage Structure
The MAX9060–MAX9063 have open-drain outputs that
allow them to interface to logic circuitry running from sup-
ply voltages other than the one supplied to the part. These
devices require an external pullup resistor or current
source for proper operation. Many microcontroller digital
inputs ports can be readily programmed to include these.
The MAX9064 has a push-pull output stage that can
both sink and source current, eliminating the need for an
external pullup resistor. In this case, the MAX9064 uses
the microcontroller’s power supply as VCC.
BUMP PIN
NAME FUNCTION
UCSP SOT23
MAX9060
MAX9061
MAX9062
MAX9063
MAX9064
MAX9060
MAX9061
MAX9062
MAX9063
MAX9064
A1 A1 5 5 OUT
Comparator Output. The MAX9060–MAX9063 have
open-drain outputs. The MAX9064 has a push-pul
output.
A2 A2 4 4 IN
Comparator Input. The MAX9060, MAX9062, and
MAX9064 have noninverting inputs. The MAX9061 and
MAX9063 have inverting inputs.
— B1 — 1 VCC
Power-Supply Voltage. Bypass to ground with a 0.1µF
bypass capacitor.
B1 — 1 — REF
External Reference Input. REF also supplies power
to the device. Bypass to ground with a 0.1µF bypass
capacitor.
B2 B2 2, 3 2, 3 GND GROUND.
MAX9060–MAX9064 Ultra-Small, nanoPower Single
Comparators in 4-Bump UCSP and 5 SOT23
www.maximintegrated.com Maxim Integrated
│
7
Pin/Bump Description
Applications Information
Bypassing REF/VCC
Place a 0.1μF capacitor between REF or VCC and GND
as close as possible to the device. During a switching
event, all comparators draw a current spike from their
power-supply rails. This current spike is minimized by the
use of an internal break-before-make design.
Hysteresis Operation
The MAX9060–MAX9064 feature internal hysteresis for
noise immunity and glitch-free operation. If additional hys-
teresis is needed, an external positive feedback network
can be easily implemented on the MAX9060, MAX9062,
and MAX9064 noninverting input devices. Additional
external hysteresis is not recommended for the MAX9061
due to possible crossover current-related noise problems.
Additional external hysteresis is not possible on the
MAX9063 because the noninverting input of the compara-
tor is not externally accessible.
Adaptive Signal Level Detector
The MAX9060 and MAX9061 can be used as an adap-
tive signal-level detector. Feed a DAC output voltage
to REF and connect the input to a variable signal level.
As the DAC output voltage is varied from 0.9V to 5.5V,
a corresponding signal level threshold-detector circuit is
implemented. See Figure 1.
Figure 1. Adaptive Signal Level Detector
Table 1. How Devices Behave Under Various Input Voltage Conditions
PART INPUT VOLTAGE CONDITIONS ACTION AT OUTPUT
MAX9060 VIN > VREF External pullup resistor pulls output high.
VIN < VREF Output asserts low.
MAX9061 VIN > VREF Output asserts low.
VIN < VREF External pullup resistor pulls output high.
MAX9062 VIN > 0.2V External pullup resistor pulls output high.
VIN < 0.2V Output asserts low.
MAX9063 VIN > 0.2V Output asserts low.
VIN < 0.2V External pullup resistor pulls output high.
MAX9064 VIN > 0.2V Output asserts high.
VIN < 0.2V Output asserts low.
MAX9060
DAC REF
IN MICROCONTROLLER
INTERNAL
PULLUP
VDD
I/OOUT
MAX9060–MAX9064 Ultra-Small, nanoPower Single
Comparators in 4-Bump UCSP and 5 SOT23
www.maximintegrated.com Maxim Integrated
│
8
Typical Operating Circuits
PART REFERENCE
VOLTAGE INPUT OUTPUT
MAX9060 External Noninverting Open drain
MAX9061 External Inverting Open drain
MAX9062 0.2V Noninverting Open drain
MAX9063 0.2V Inverting Open drain
MAX9064 0.2V Noninverting Push-pull
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE
NO.
LAND
PATTERN NO.
5 SOT23 U5+2 21-0057 90-0174
4 UCSP B4+1 21-0117 —
MAX9060
REF
IN MICROCONTROLLER
INTERNAL
PULLUP
VDD
I/OOUT
0.9V
TO 5.5V
MAX9062
IN MICROCONTROLLER
INTERNAL
PULLUP
VDD
VCC = 1.0V TO 5.5V
I/OOUT
0.2V REF
MAX9064
IN MICROCONTROLLER
VDD
VCC = 1.0V TO 5.5V
I/OOUT
0.2V REF
MAX9061
REF
IN MICROCONTROLLER
INTERNAL
PULLUP
VDD
I/OOUT
0.9V
TO 5.5V
MAX9063
IN MICROCONTROLLER
INTERNAL
PULLUP
VDD
VCC = 1.0V TO 5.5V
I/OOUT
0.2V REF
MAX9060–MAX9064 Ultra-Small, nanoPower Single
Comparators in 4-Bump UCSP and 5 SOT23
www.maximintegrated.com Maxim Integrated
│
9
Selector Guide Package Information
For the latest package outline information and land patterns
(footprints), go to www.maximintegrated.com/packages. Note
that a “+”, “#”, or “-” in the package code indicates RoHS status
only. Package drawings may show a different suffix character, but
the drawing pertains to the package regardless of RoHS status.
Chip Information
PROCESS: BiCMOS
REVISION
NUMBER
REVISION
DATE DESCRIPTION PAGES
CHANGED
0 5/08 Initial release —
1 1/09 Corrected ultra-low operating current value 1
2 10/10 Updated TOC 4 labels 4
3 12/10 Added G45 designation 1
4 3/11 Updated Note 6 3
5 8/12 Added automotive package MAX9064EUK/V+T to Ordering Information 1
6 12/14 Added automotive package MAX9063EUK/V+T to Ordering Information and removed
MAX9064EUK/V+T 1
7 3/17 Updated title to include “nanoPower” and updated top marking in Ordering Information
table 1–10
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses
are implied. Maxim Integrated reserves the right to change the circuitry and specications without notice at any time. The parametric values (min and max limits)
shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
MAX9060–MAX9064 Ultra-Small, nanoPower Single
Comparators in 4-Bump UCSP and 5 SOT23
© 2017 Maxim Integrated Products, Inc.
│
10
Revision History
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com.