RADIALL TECHNICAL DATA SHEET R 595 - - - - - - H HIIG GH HP PE ER RFFO OR RM MA AN NC CE ED DP P33TT -- S SP PD DTT S SW WIITTC CH HE ES S Issue : 09-March-2010 DP3T - SPDT Coaxial Switches DC to 6 GHz, DC to 20 GHz, DC to 26.5 GHz Radiall's PLATINUM SERIES switches are optimised to perform at a high level over an extended life span. With outstanding RF performances, and a guaranteed Insertion Loss repeatability of 0.03 dB over a life span of 10 million switching cycles. PLATINUM SERIES switches are perfect for automated test and measurement equipment, as well as signal monitoring devices. PART NUMBER SELECTION R 595 . . . . . . . RF Connectors : Documentation : - : Certificate Of Conformity 3 : SMA up to 6 GHz 4 : SMA up to 20 GHz F : SMA up to 26.5 GHz C : Calibration certificate R : Calibration certificate + RF curves Type : 3 : Latching 4 : Latching + Indicators 5 : Latching + Self Cut-Off 6 : Latching + Self Cut-Off + Indicators Actuator Terminal : 0 : Solder pins 5 : D-Sub connector Options : 1 : Without option (Positive common) 2 : Compatible TTL driver (high level) Actuator Voltage : 3 : 24 Vdc 7 : 15 Vdc Switch model : 1 : Non terminated SPDT switch 2 : Terminated SPDT switch 3 : Terminated 4 port bypass switch 4 : Non terminated 5 port DP3T switch PICTURE ISO 9001 certified www.radiall.com Page 1 E-Mail : switchingproducts@radiall.com RADIALL R 595 - - - - - - TECHNICAL DATA SHEET H HIIG GH HP PE ER RFFO OR RM MA AN NC CE ED DP P33TT -- S SP PD DTT S SW WIITTC CH HE ES S Issue : 09-March-2010 RF PERFORMANCES PART NUMBER Frequency Range Impedance GHz R5953----- R5954----- R595F----- DC to 6 DC to 20 DC to 26.5 Ohms 50 Insertion Loss dB (Maximum) 0.20 + (0.45 / 26.5) x frequency (GHz) 85 75 65 DC to 6 GHz 6 to 12.4 GHz 12.4 to 20 GHz 20 to 26.5 GHz 1.15 1.25 1.30 1.60 DC to 6 GHz : 6 to 12.4 GHz : 12.4 to 18 GHz : 18 to 26.5 GHz : DC to 6 GHz : 6 to 12.4 GHz : 12.4 to 20 GHz : Isolation dB (Minimum) 85 V.S.W.R. (Maximum) 1.15 Repeatability (Up to 10 million cycles measured at 25C) 0.03 dB maximum DC to 6 GHz 6 to 12.4 GHz 12.4 to 18 GHz 18 to 20 GHz : : : : 0.03 dB maximum : : : : 85 75 65 60 1.15 1.25 1.30 1.60 0.03 dB maximum TYPICAL RF PERFORMANCES 0 1.70 -0,4 -20 1.60 -0,8 -40 -1,2 -60 -1,6 -80 Isolation dB 0 1.50 1.40 IL dB 1.30 1.20 -2 -2,4 -100 0.10 GHz 26.5 Insertion Loss and Isolation ISO 9001 certified www.radiall.com -120 1.10 1.00 0.10 GHz 26.5 V.S.W.R. Page 2 E-Mail : switchingproducts@radiall.com RADIALL TECHNICAL DATA SHEET R 595 - - - - - - H HIIG GH HP PE ER RFFO OR RM MA AN NC CE ED DP P33TT -- S SP PD DTT S SW WIITTC CH HE ES S Issue : 09-March-2010 ADDITIONAL SPECIFICATIONS Operating mode Latching Nominal operating voltage (across operating temperature) Vdc Coil resistance (+/-10%) 24 (20 / 32) 15 (12 / 20) SPDT 350 120 Terminated SPDT, DP3T, Bypass 175 60 SPDT 68 125 Terminated SPDT, DP3T, Bypass 140 250 Ohms Nominal operating current at 23C mA RF path Cold switching : see Power Rating Chart on page 12 Hot switching : 1 Watt CW Average power Internal terminations TTL input 1 Watt average into 50 High Level 3 to 7 V 800 A max at 7 V Low Level 0 to 0.8 V 20 A max at 0.8V Switching time (max) ms 15 Life (min) 10 million cycles Connectors SMA D-Sub 9 pin female Solder pins Actuator terminals Weight (max) SPDT < 60 Terminated SPDT, DP3T, Bypass < 100 g ENVIRONMENTAL SPECIFICATIONS Operating temperature range C -25 to +75 Storage temperature range C -55 to +85 Temperature cycling (MIL-STD-202F , Method 107D , Cond.A) C -55 to +85 (10 cycles) Sine vibration operating (MIL STD 202 , Method 204D , Cond.D) Random vibration operating Shock operating (MIL STD 202 , Method 213B , Cond.G) Humidity operating 10-2000 Hz, 20g 16.91g (rms) 50-2000 Hz 3min/axis 50g / 11 ms, sawtooth 15 to 95% relative humidity Humidity storage (MIL STD 202 , Method 106E , Cond.E) 65C, 95% RH, 10 days Altitude operating 15,000 feet (4,600 meters) Altitude storage (MIL STD 202 , Method 105C , Cond.B) 50,000 feet (15,240 meters) ISO 9001 certified www.radiall.com Page 3 E-Mail : switchingproducts@radiall.com RADIALL TECHNICAL DATA SHEET R 595 - - - - - - H HIIG GH HP PE ER RFFO OR RM MA AN NC CE ED DP P33TT -- S SP PD DTT S SW WIITTC CH HE ES S Issue : 09-March-2010 SWITCH MODEL 1 : NON TERMINATED SPDT SWITCH The non terminated SPDT switch is a single pole double throw switch. This switch is "break before make". RF SCHEMATIC DIAGRAM POSITION E1 POSITION E2 POSITION INDICATORS STATE "11" STATE "22" Standard drive option "1" (Positive common): * Connect pin +Vcc to supply. * Select desired RF path by applying ground to the corresponding "close" pin (Ex: ground pin E1 to switch to position E1. RF path 1-2 closed and RF path 2-3 open). * To open desired path and close the new RF path, connect ground to the corresponding "close" pin (Ex: ground pin E2 to open RF path 1-2 and close RF path 2-3). D-Sub connector Solder pins ISO 9001 certified www.radiall.com TTL drive option "2" * Connect pin GND to ground. * Connect pin +Vcc to supply * Select (close) desired RF path by applying TTL "High " to the corresponding "drive" pin (Ex: apply TTL "High" to pin E1 to switch to position E1. RF path 1-2 closed and RF path 2-3 open). * To open desired path and close the new RF path, apply TTL "High" to the "drive" pin which corresponds to the desired RF path. (Ex: apply TTL "High" to pin E2 to open RF path 1-2 and close RF path 2-3). D-Sub connector Solder pins Page 4 E-Mail : switchingproducts@radiall.com RADIALL TECHNICAL DATA SHEET R 595 - - - - - - H HIIG GH HP PE ER RFFO OR RM MA AN NC CE ED DP P33TT -- S SP PD DTT S SW WIITTC CH HE ES S Issue : 09-March-2010 All dimensions are in inches/millimetres. With D-Sub connector ISO 9001 certified www.radiall.com With solder pins Page 5 E-Mail : switchingproducts@radiall.com RADIALL TECHNICAL DATA SHEET R 595 - - - - - - H HIIG GH HP PE ER RFFO OR RM MA AN NC CE ED DP P33TT -- S SP PD DTT S SW WIITTC CH HE ES S Issue : 09-March-2010 SWITCH MODEL 2 : TERMINATED SPDT SWITCH The terminated SPDT switch is a single pole double throw switch. The unused ports are terminated into 50 ohms. This switch is "break before make". RF SCHEMATIC DIAGRAM POSITION E1 POSITION E2 POSITION INDICATORS STATE "11" STATE "22" Standard drive option "1" (Positive common): * Connect pin +Vcc to supply. * Select desired RF path by applying ground to the corresponding "close" pin (Ex: ground pin E1 to switch to position E1. RF path 1-2 closed and RF path 2-3 open). * To open desired path and close the new RF path, connect ground to the corresponding "close" pin (Ex: ground pin E2 to open RF path 1-2 and close RF path 2-3). D-Sub connector Solder pins ISO 9001 certified www.radiall.com TTL drive option "2" * Connect pin GND to ground. * Connect pin +Vcc to supply * Select (close) desired RF path by applying TTL "High " to the corresponding "drive" pin (Ex: apply TTL "High" to pin E1 to switch to position E1. RF path 1-2 closed and RF path 2-3 open). * To open desired path and close the new RF path, apply TTL "High" to the "drive" pin which corresponds to the desired RF path. (Ex: apply TTL "High" to pin E2 to open RF path 1-2 and close RF path 2-3). D-Sub connector Solder pins Page 6 E-Mail : switchingproducts@radiall.com RADIALL TECHNICAL DATA SHEET R 595 - - - - - - H HIIG GH HP PE ER RFFO OR RM MA AN NC CE ED DP P33TT -- S SP PD DTT S SW WIITTC CH HE ES S Issue : 09-March-2010 All dimensions are in inches/millimetres. With D-Sub connector ISO 9001 certified www.radiall.com With solder pins Page 7 E-Mail : switchingproducts@radiall.com RADIALL TECHNICAL DATA SHEET R 595 - - - - - - H HIIG GH HP PE ER RFFO OR RM MA AN NC CE ED DP P33TT -- S SP PD DTT S SW WIITTC CH HE ES S Issue : 09-March-2010 SWITCH MODEL 3 : TERMINATED 4 PORT BYPASS SWITCH The terminated 4 port bypass switch can terminate into 50 ohms the device under test. These switches are "break before make". RF SCHEMATIC DIAGRAM POSITION E1 POSITION E2 POSITION INDICATORS STATE "11" STATE "22" Standard drive option "1" (Positive common): * Connect pin +Vcc to supply. * Select desired RF path by applying ground to the corresponding "close" pin (Ex: ground pin E1 to switch to position E1. RF path 1-2 and RF path 3-4 closed and RF path 2-3 open). * To open desired path and close the new RF path, connect ground to the corresponding "close" pin (Ex: ground pin E2 to open RF path 1-2 and 3-4 and close RF path 2-3). D-Sub connector Solder pins ISO 9001 certified www.radiall.com TTL drive option "2" * Connect pin GND to ground. * Connect pin +Vcc to supply. * Select (close) desired RF path by applying TTL "High " to the corresponding "drive" pin (Ex: apply TTL "High" to pin E1 to switch to position E1. RF path 1-2 and 3-4 closed and RF path 2-3 open). * To open desired path and close the new RF path, apply TTL "High" to the "drive" pin which corresponds to the desired RF path. (Ex: apply TTL "High" to pin E2 to open RF path 1-2 and 3-4 and close RF path 2-3). D-Sub connector Solder pins Page 8 E-Mail : switchingproducts@radiall.com RADIALL TECHNICAL DATA SHEET R 595 - - - - - - H HIIG GH HP PE ER RFFO OR RM MA AN NC CE ED DP P33TT -- S SP PD DTT S SW WIITTC CH HE ES S Issue : 09-March-2010 All dimensions are in inches/millimetres. With D-Sub connector ISO 9001 certified www.radiall.com With solder pins Page 9 E-Mail : switchingproducts@radiall.com RADIALL TECHNICAL DATA SHEET R 595 - - - - - - H HIIG GH HP PE ER RFFO OR RM MA AN NC CE ED DP P33TT -- S SP PD DTT S SW WIITTC CH HE ES S Issue : 09-March-2010 SWITCH MODEL 4 : NON TERMINATED 5 PORT DP3T SWITCH The non terminated 5 port DP3T switch can used as SPDT with high power terminations, as a bypass switch. In this application, the fifth port can be terminated externally with a high power termination. These switches are "break before make". RF SCHEMATIC DIAGRAM POSITION E1 POSITION E2 POSITION INDICATORS STATE "11" STATE "22" Standard drive option "1" (Positive common): * Connect pin +Vcc to supply. * Select desired RF path by applying ground to the corresponding "close" pin (Ex: ground pin E1 to switch to position E1. RF path 2-3 and RF path 4-5 closed and RF path 1-2 and RF path 3-4 open). * To open desired path and close the new RF path, connect ground to the corresponding "close" pin (Ex: ground pin E2 to open RF path 2-3 and 4-5 and close RF path 1-2 and 3-4). D-Sub connector Solder pins ISO 9001 certified www.radiall.com TTL drive option "2" * Connect pin GND to ground. * Connect pin +Vcc to supply. * Select (close) desired RF path by applying TTL "High " to the corresponding "drive" pin (Ex: apply TTL "High" to pin E1 to switch to position E1. RF path 2-3 and RF path 4-5 closed and RF path 1-2 and 3-4 open). * To open desired path and close the new RF path, apply TTL "High" to the "drive" pin which corresponds to the desired RF path. (Ex: apply TTL "High" to pin E2 to open RF path 2-3 and 4-5 and close RF path 1-2 and 3-4). D-Sub connector Solder pins Page 10 E-Mail : switchingproducts@radiall.com RADIALL TECHNICAL DATA SHEET R 595 - - - - - - H HIIG GH HP PE ER RFFO OR RM MA AN NC CE ED DP P33TT -- S SP PD DTT S SW WIITTC CH HE ES S Issue : 09-March-2010 All dimensions are in inches/millimetres. With D-Sub connector ISO 9001 certified www.radiall.com With solder pins Page 11 E-Mail : switchingproducts@radiall.com RADIALL TECHNICAL DATA SHEET R 595 - - - - - - H HIIG GH HP PE ER RFFO OR RM MA AN NC CE ED DP P33TT -- S SP PD DTT S SW WIITTC CH HE ES S Issue : 09-March-2010 POWER RATING CHART AVERAGE POWER RATING (Watts) This graph is based on the following conditions : - Ambient temperature : + 25C - Sea level - V.S.W.R. : 1 and cold switching 10000 1000 SMA 100 10 0.1 1 10 100 18 26.5 GHz FREQUENCY (GHz) DERATING FACTOR VERSUS V.S.W.R. The average power input must be reduced for load V.S.W.R. above 1. 1 DERATING FACTOR 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 1 2 3 4 5 6 7 8 9 10 V.S.W.R. ISO 9001 certified www.radiall.com Page 12 E-Mail : switchingproducts@radiall.com Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Radiall: R595447215 R595357125 R595333110 R595F33210 R595333310 R595F37120 R595463225 R595467125 R595F37225 R595437125 R595333210 R595457225 R595F63215 R595F33310 R595337110 R595F63225 R595F33110 R595433210 R595363425 R595433225 R595F33215 R595357225 R595F63115 R595343125 R595343215 R595343115 R595443215 R595F43110 R595467215 R595347210 R595433410 R595443315 R595357325 R595333215 R595467225 R595463215 R595F67110 R595F33115 R595353215