19-0989; Rev 0; 10/07 KIT ATION EVALU E L B A AVAIL Six-String White LED Driver with Active Current Balancing for LCD Panel Applications The MAX8790A is a high-efficiency driver for white lightemitting diodes (LEDs). It is designed for large liquidcrystal displays (LCDs) that employ an array of LEDs as the light source. A current-mode step-up controller drives up to six parallel strings of multiple series-connected LEDs. Each string is terminated with ballast that achieves 1.5% current regulation accuracy, ensuring even brightness for all LEDs. The MAX8790A has a wide input-voltage range from 4.5V to 26V, and provides a fixed 20mA or adjustable 15mA to 27mA full-scale LED current. The MAX8790A has two dimming control modes to enable a wide variety of applications. In direct DPWM mode, the LED current is directly turned on and off by a PWM signal. In analog dimming mode, an internal phase-locked loop (PLL) circuit translates the PWM signal into an analog signal and linearly controls the LED current down to 12.5%. Below 12.5%, digital dimming is added to allow lower average LED current down to 1%. Both control methods provide 100:1 dimming range. The MAX8790A has multiple features to protect the controller from fault conditions. Separate feedback loops limit the output voltage if one or more LEDs fail open or short. The controller features cycle-by-cycle current limit to provide consistent operation and soft-start capability. A thermal-shutdown circuit provides another level of protection. The step-up controller uses an external MOSFET, which provides good efficiency and allows for scalable output power and maximum operating voltage. Low feedback voltage at each LED string (450mV) helps reduce power loss. The MAX8790A features selectable switching frequency (500kHz, 750kHz, or 1MHz), which allows trade-offs between external component size and ope-rating efficiency. The MAX8790A is available in a thermally enhanced, lead-free, 20-pin, 4mm x 4mm, Thin QFN package. Features o Drives Six Parallel Strings with Multiple SeriesConnected LEDs per String o 1.5% Current Regulation Accuracy Between Strings o Low 450mV Feedback Voltage at Full Current Improves Efficiency o Step-Up Controller Regulates the Output Just Above the Highest LED String Voltage o Full-Scale LED Current Adjustable from 15mA to 27mA, or Preset 20mA o Wide 100:1 Dimming Range o Programmable Dimming Control: Direct DPWM or Analog Dimming o o o o Built-In PLL for Synchronized Dimming Control Open and Short LED Protections Output Overvoltage Protection Wide Input Voltage Range from 4.5V to 26V o External MOSFET Allows a Large Number of LEDs per String o 500kHz/750kHz/1MHz Switching Frequency o Small, 20-Pin, 4mm x 4mm Thin QFN Package Simplified Operating Circuit VOUT 0.1F SHDN IN VCC FSET ISET EXT N1 CS Rs MAX8790A Notebook, Subnotebook, and Tablet Computer Displays Handy Terminals D1 CIN Applications Automotive Systems L1 VIN GND BRT R1 N.C. OSC N.C. CPLL OV R2 CCV FB1 Ordering Information PART TEMP RANGE PIN-PACKAGE MAX8790AETP+ -40C to +85C +Denotes a lead-free package. 20 Thin QFN (4mm x 4mm) PKG CODE FB2 ENA FB3 FB4 EP FB5 FB6 T2044-3 Pin Configuration appears at end of data sheet. ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. 1 MAX8790A General Description MAX8790A Six-String White LED Driver with Active Current Balancing for LCD Panel Applications ABSOLUTE MAXIMUM RATINGS IN, SHDN, to GND .................................................-0.3V to +28V FB_ to GND ............................................................-0.3V to +28V VCC, BRT, ENA, OSC, OV to GND ...........................-0.3V to +6V ISET, CCV, CS, FSET, CPLL, EXT to GND .-0.3V to (VCC + 0.3V) Continuous Power Dissipation (TA = +70C) 20-Pin Thin QFN (derate 16.9mW/C above +70C) ...1349mW Operating Temperature Range ...........................-40C to +85C Junction Temperature ......................................................+150C Storage Temperature Range .............................-60C to +150C Lead Temperature (soldering, 10s) .................................+300C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (Circuit of Figure 1. VIN = 12V, V SHDN = VIN, CCV = 0.1F, TA = 0C to +85C, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER IN Input Voltage Range IN Quiescent Current CONDITIONS MIN TYP VIN = VCC 4.5 5.5 VCC = bypassed to GND through 1F capacitor 5.5 26.0 V SHDN = high, BRT = GND VIN = 26V 1 2 VIN = VCC = 5V 1 2 SHDN = GND VCC Output voltage MAX V SHDN = 5V, 6V < VIN < 26V, 0 < IVCC < 10mA 10 UNITS V mA A 4.7 5.0 5.3 V 15 56 130 mA Rising edge, hysteresis = 20mV 4.00 4.25 4.45 V EXT High Level 10mA from EXT to GND VCC 0.1 VCC EXT Low Level -10mA from EXT to VCC 0 0.1 V EXT On-Resistance EXT high or low 2 5 EXT Sink/Source Current EXT forced to 2V 1 VCC Short-Circuit Current VCC UVLO Threshold STEP-UP CONVERTER OSC Midlevel Threshold V VCC 2.0 1.5 OSC Low-Level Threshold Minimum Duty Cycle V 0.4 V VOSC = VCC 0.9 1.0 1.1 MHz VOSC = open 675 750 825 VOSC = GND 450 500 550 PWM mode 10 Pulse skipping, no load 0 Maximum Duty Cycle CS Trip Voltage A VCC 0.4 OSC High-Level Threshold Operating Frequency V Duty cycle = 75% 94 95 85 100 kHz % % 115 mV CONTROL INPUT SHDN Logic-Input High Level 2.1 SHDN Logic-Input Low Level BRT, ENA Logic-Input High Level 2.1 BRT, ENA Logic-Input Low Level 2 V 0.8 _______________________________________________________________________________________ V V 0.8 V Six-String White LED Driver with Active Current Balancing for LCD Panel Applications (Circuit of Figure 1. VIN = 12V, V SHDN = VIN, CCV = 0.1F, TA = 0C to +85C, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER CONDITIONS MIN TYP MAX UNITS +42 A INPUT LEAKAGE SHDN Leakage Current SHDN = 26V CS Leakage Current VCS = GND +50 A OSC Leakage Current -3 +3 A BRT, ENA Leakage Current -1 +1 A -1 +1 A -0.1 +0.1 A FSET, ISET Leakage Current FSET = ISET = VCC OV Leakage Current +40 LED CURRENT Full-Scale FB_ Output Current ISET High-Level Threshold ISET = VCC, BRT = 100% 19.40 20.00 20.60 RISET = 80k to GND, BRT = 100% 24.25 25.00 25.75 RISET = 133k to GND, BRT = 100% 14.40 15.00 15.60 Default setting for 20mA full-scale LED current VCC 0.4 ISET Voltage mA V 1.12 1.19 4.00 1.26 V 4.16 mA 20% Output Current ISET = VCC, BRT = 20% 3.84 Current Regulation Between Strings ISET = VCC, BRT = 100% -1.5 +1.5 % ISET = VCC, BRT = 20% -2.0 +2.0 % RISET = 80k to GND, BRT = 100% 300 500 ISET = VCC, BRT = 100% 270 450 720 ISET = VCC, 12.5% 150 275 500 120 200 mVP-P 13 20 Minimum FB_ Regulation Voltage Maximum FB_ Ripple ISET = VCC , C OUT = 1F, OSC = VCC (Note 1) FB_ On-Resistance VFB_ = 50mV FB_ Leakage Current SHDN = GND, VFB_ = 26V Minimum BRT Duty Cycle 1 SHDN = VIN, BRT = GND, VFB_ = 15V BRT Input Frequency 800 10 100 PLL active 28 500 12.5 mV A Hz % FAULT PROTECTION OV Threshold Voltage FB_ Overvoltage Threshold FAULT Shutdown Timer VFB_ > 5.6V (typ) Thermal-Shutdown Threshold (Note 1) 1.16 1.23 1.30 V VCC + 0.20 VCC + 0.6 VCC + 1.45 V 50 65 80 ms 170 C PHASE-LOCKED LOOP FSET High-Level Threshold BRT Frequency Capture Range PLL disabled VCC 0.4 V RFSET = 500k 150 200 250 RFSET = 250k 300 400 500 Hz _______________________________________________________________________________________ 3 MAX8790A ELECTRICAL CHARACTERISTICS (continued) MAX8790A Six-String White LED Driver with Active Current Balancing for LCD Panel Applications ELECTRICAL CHARACTERISTICS (Circuit of Figure 1. VIN = 12V, V SHDN = VIN, CCV = 0.1F, TA = -40C to +85C, unless otherwise noted.) (Note 2) PARAMETER IN Input Voltage Range CONDITIONS MIN TYP 4.5 5.5 VCC bypassed to GND through 1F cap 5.5 26.0 IN Quiescent Current V = high BRT = GND VCC Output Voltage V VIN = 26V 2 VIN = VCC = 5V 2 = GND = 5V, 6V < VIN < 26V, 0 < I VCC < 10mA 10 UNITS V mA A 4.7 5.3 V 12 130 mA Rising edge, hysteresis = 20mV 4.00 4.45 V 10mA from EXT to GND VCC 0.1 VCC Short-Circuit Current VCC UVLO Threshold MAX VIN = VCC STEP-UP CONVERTER EXT High Level EXT Low Level -10mA from EXT to VCC EXT On-Resistance EXT high or low 0.1 OSC Midlevel Threshold V 1.5 VCC 2.0 OSC Low-Level Threshold V 0.4 V VOSC = VCC VOSC = open 0.9 1.1 MHz 675 825 VOSC = GND 450 550 Maximum Duty Cycle CS Trip Voltage V 5 VCC 0.4 OSC High-Level Threshold Operating Frequency V 94 Duty cycle = 75% 85 kHz % 115 mV CONTROL INPUT Logic-Input High Level 2.1 Logic-Input Low Level V 0.8 BRT, ENA Logic-Input High 2.1 BRT, ENA Logic-Input Low Level V V 0.8 V +42 A INPUT LEAKAGE Leakage Current CS Leakage Current = 26V +50 A OSC Leakage Current -3 +3 A BRT, ENA Leakage Current -1 +1 A -1 +1 A -0.1 +0.1 A FSET, ISET Leakage Current OV Leakage Current 4 VCS = GND FSET = ISET = VCC _______________________________________________________________________________________ Six-String White LED Driver with Active Current Balancing for LCD Panel Applications (Circuit of Figure 1. VIN = 12V, V SHDN = VIN, CCV = 0.1F, TA = -40C to +85C, unless otherwise noted.) (Note 2) PARAMETER CONDITIONS MIN TYP MAX UNITS LED CURRENT Full-Scale FB_ Output Current ISET High-Level Threshold ISET = VCC, BRT = 100% 19.2 20.8 RISET = 80k to GND, BRT = 100% 24.0 26.0 RISET = 133k to GND, BRT = 100% 14.4 15.6 Default setting for 20mA full-scale LED current VCC 0.4 ISET Voltage mA V 1.12 1.26 V 20% Output Current ISET = VCC, BRT = 20% 3.8 4.2 mA Current Regulation Between Strings ISET = VCC, BRT = 100% -2 +2 ISET = VCC, BRT = 20% -3 +3 RISET = 80k to GND, BRT = 100% 280 840 ISET= VCC, BRT = 100% 250 760 ISET = VCC, BRT = 12.5% 140 530 Minimum FB_ Regulation Voltage % mV Maximum FB_ Ripple ISET= VCC, COUT = 1F, OSC = VCC (Note 1) 200 mVP-P FB_ On-Resistance VFB_ = 50mV 20 SHDN = GND, VFB_ = 26V 1 SHDN = VIN, BRT = GND, VFB_ = 15V 28 FB_ Leakage Current BRT Input Frequency A 100 500 Hz 1.16 1.30 V VCC + 0.2 VCC + 1.45 V 50 80 ms FAULT PROTECTION OV Threshold Voltage FB_ Overvoltage Threshold FAULT Shutdown Timer VFB_ > 5.6V (typ) PHASE-LOCKED LOOP FSET High-Level Threshold BRT Frequency Capture Range PLL disabled VCC 0.4 V RFSET = 500k 150 250 Hz RFSET = 250k 300 500 Hz Note 1: Specifications are guaranteed by design, not production tested. Note 2: Specifications to -40C are guaranteed by design, not production tested. _______________________________________________________________________________________ 5 MAX8790A ELECTRICAL CHARACTERISTICS (continued) Typical Operating Characteristics (Circuit configuration 1, VIN = 12V, V SHDN = VIN, LEDs = 8 series x 6 parallel strings, ISET = VCC, TA = +25C, unless otherwise noted.) NORMALIZED POWER 750kHz 90 89 1MHz 0.8 TOTAL INPUT POWER, ANALOG 0.6 88 1 12 17 INPUT VOLTAGE (V) 20.4 20.2 20.0 19.8 19.6 19.4 0 0.04 0.03 DPWM DIMMING BRT = 10% 0.02 0.01 0 -0.01 DPWM DIMMING BRT = 100% -0.02 -0.03 ANALOG DIMMING BRT = 10% -0.04 20 40 60 AMBIENT TEMPERATURE () 80 5 BRT = 100% 4 3 BRT = 0% 2 0.5 0.4 0.3 0.2 5 10 15 20 25 LED STRING CURRENT (mA) SWITCHING WAVEFORMS (BRT = 100%) 6 VLX 10V/div 5 4 0V 3 2 IL 500mA/div 0mA 1 1 0 0 7 12 17 INPUT VOLTAGE (V) 30 MAX8790A toc09 7 SHUTDOWN CURRENT (A) 6 0.6 0 12 17 INPUT VOLTAGE (V) SHUTDOWN CURRENT vs. INPUT VOLTAGE MAX8790A toc07 7 0.7 0 7 SUPPLY CURRENT vs. INPUT VOLTAGE (DPWM DIMMING) 100 0.1 -0.05 19.0 10 BRT DUTY CYCLE (%) FB_ VOLTAGE vs. LED CURRENT (ANALOG DIMMING) MAX8790A toc05 0.05 19.2 0 1 1000 MAX8790A toc08 LED CURRENT (mA) 20.6 10 LED CURRENT REGULATION vs. INPUT VOLTAGE LED CURRENT REGULATION (%) MAX8790A toc04 20.8 10 100 TOTAL LED CURRENT (mA) FB_ REGULATION VOLTAGE (V) LED CURRENT vs. AMBIENT TEMPERATURE (BRT = 100%) 21.0 15 5 TOTAL LED POWER, ANALOG 0 7 IDENTICAL FOR DPWM DIMMING AND ANALOG DIMMING 20 0.2 87 86 6 TOTAL LED POWER, DPWM TOTAL INPUT POWER, DPWM 0.4 MAX8790A toc03 500kHz 92 1.0 25 MAX8790A toc06 93 NORMALIZED TO VIN = 20V, AND ILED = 20mA VIN = 7V LED CURRENT (mA) 1.2 MAX8790A toc01 BOOST CONVERTER EFFICIENCY (%) 94 91 LED CURRENT vs. BRT DUTY CYCLE (BRT AT 200Hz) NORMALIZED POWER vs. TOTAL LED CURRENT (ANALOG AND DPWM DIMMING) MAX8790A toc02 BOOST CONVERTER EFFICIENCY vs. INPUT VOLTAGE (BRT = 100%) SUPPLY CURRENT (mA) MAX8790A Six-String White LED Driver with Active Current Balancing for LCD Panel Applications 7 12 17 INPUT VOLTAGE (V) 200ns/div _______________________________________________________________________________________ Six-String White LED Driver with Active Current Balancing for LCD Panel Applications SWITCHING WAVEFORMS (BRT = 15%, ANALOG DIMMING) LED CURRENT WAVEFORMS (BRT = 50% AT 200Hz, DPWM DIMMING) STARTUP WAVEFORMS (BRT = 100%, DPWM DIMMING) MAX8790A toc11 MAX8790A toc10 MAX8790A toc12 0V VLX 10V/div 0V SHDN 5V/div 0V VOUT 20V/div 0V 0V 0A 1s/div 0mA 100mA/div IL 1A/div 0A LED CURRENT WAVEFORMS (BRT = 50% AT 200Hz, ANALOG DIMMING) MAX8790A toc14 MAX8790A toc13 0V 0V BRT 5V/div 0V VFB1 5V/div 0V BRT 5V/div VFB1 1V/div ILED ILED 0mA 100mA/div 0mA 50mA/div 0A IL 1A/div 0A 1ms/div 1ms/div LED CURRENT WAVEFORMS (BRT = 1% AT 200Hz, ANALOG DIMMING) LED-OPEN FAULT PROTECTION (BRT = 100%, LED OPEN ON FB3) MAX8790A toc15 IL 1A/div MAX8790A toc16 0V 0V BRT 5V/div 0V VFB1 2V/div 0V ILED 0mA VFB3 1V/div VFB1 10V/div VOUT 0V 20V/div 0mA 50mA/div 1ms/div IL 1A/div 2ms/div 4ms/div LED CURRENT WAVEFORMS (BRT = 1% AT 200Hz, DPWM DIMMING) VFB1 5V/div ILED VCCV 0V 2V/div IL 500mA/div 0mA BRT 5V/div IL 500mA/div 0A IL 1A/div 20ms/div _______________________________________________________________________________________ 7 MAX8790A Typical Operating Characteristics (continued) (Circuit configuration 1, VIN = 12V, V SHDN = VIN, LEDs = 8 series x 6 parallel strings, ISET = VCC, TA = +25C, unless otherwise noted.) Typical Operating Characteristics (continued) (Circuit configuration 1, VIN = 12V, V SHDN = VIN, LEDs = 8 series x 6 parallel strings, ISET = VCC, TA = +25C, unless otherwise noted.) LED-SHORT FAULT PROTECTION (BRT = 100%, 2 LEDs SHORT ON FB3) LED CURRENT BALANCING vs. INPUT VOLTAGE (BRT = 100%) 0V 0V VFB3 1V/div VFB1 10V/div VOUT 0V 20V/div 0A 10ms/div IL 1A/div 1.00 MAX8790A toc18 MAX8790A toc17 LED CURRENT BALANCING ACCURACY (%) MAX8790A Six-String White LED Driver with Active Current Balancing for LCD Panel Applications 0.90 0.80 0.70 0.60 1MHz 0.50 0.40 0.30 500kHz 0.20 750kHz 0.10 0 7 12 17 INPUT VOLTAGE (V) Pin Description 8 PIN NAME FUNCTION 1 OSC Oscillator Frequency Selection Pin. Connect OSC to VCC to set the step-up converter's oscillator frequency to 1MHz. Connect OSC to GND to set the frequency to 500kHz. Float OSC to set the frequency to 750kHz. 2 ENA Analog Dimming Enable. ENA sets the PWM control mode. Set ENA LOW to enable direct DPWM dimming. Set ENA HIGH to enable analog dimming. In both modes, the duty cycle of the PWM signal at the BRT input controls the LED current characteristics. See the Dimming Control section for a complete description. 3 BRT Brightness Control Input. The duty cycle of this digital input signal controls the LED current characteristics. The allowable frequency range is 100Hz to 500Hz in analog dimming mode. The duty cycle can be 100% to 1%. The BRT frequency can go above 500Hz in direct DPWM mode as long as the BRT pulse width is greater than 50s minimum. See the Dimming Control section for a complete description. 4 SHDN Shutdown Control Input. The MAX8790A shuts down when SHDN is less than 0.8V. Pulling SHDN above 2.1V enables the MAX8790A. SHDN can be connected to the input voltage if desired. 5 FB1 LED String 1 Cathode Connection. FB1 is the open-drain output of an internal regulator, which controls current through FB1. FB1 can sink up to 27mA. If unused, connect FB1 to GND. 6 FB2 LED String 2 Cathode Connection. FB2 is the open-drain output of an internal regulator, which controls current through FB2. FB2 can sink up to 27mA. If unused, connect FB2 to GND. 7 FB3 LED String 3 Cathode Connection. FB3 is the open-drain output of an internal regulator, which controls current through FB3. FB3 can sink up to 27mA. If unused, connect FB3 to GND. 8 GND Ground 9 FB4 LED String 4 Cathode Connection. FB4 is the open-drain output of an internal regulator, which controls current through FB4. FB4 can sink up to 27mA. If unused, connect FB4 to GND. 10 FB5 LED String 5 Cathode Connection. FB5 is the open-drain output of an internal regulator, which controls current through FB5. FB5 can sink up to 27mA. If unused, connect FB5 to GND. _______________________________________________________________________________________ Six-String White LED Driver with Active Current Balancing for LCD Panel Applications PIN NAME 11 FB6 LED String 6 Cathode Connection. FB6 is the open-drain output of an internal regulator, which controls current through FB6. FB6 can sink up to 27mA. If unused, connect FB6 to GND. 12 CS Step-Up Controller Current-Sense Input. Connect the CS input to a ground-referenced sense resistor to measure the current in the external MOSFET switch. 13 EXT External MOSFET Gate-Drive Output OV Overvoltage Sense. Connect OV to the center tap of a resistive voltage-divider from VOUT to ground. The detection threshold for voltage limiting at OV is 1.23V (typ). 15 VCC 5V Linear Regulator Output. VCC provides power to the MAX8790A and is also used to bias the gate driver for the external MOSFET. Bypass VCC to GND with a ceramic capacitor of 1F or greater. If VIN is less than or equal to 5.5V, connect VCC to IN to the disable the internal LDO and use the external 5V supply to VCC. When SHDN is low, the internal linear regulator is disabled. 16 IN Supply Input. VIN biases the internal 5V linear regulator that powers the device. Bypass IN to GND directly at the pin with a 0.1F or greater ceramic capacitor. 17 CCV Step-Up Converter Compensation Pin. Connect a 0.1F ceramic capacitor and 1.2k resistor from CCV to GND. When the MAX8790A shuts down, CCV is discharged to 0V through an internal 20k resistor. ISET Full-Scale LED Current Adjustment Pin. The resistance from ISET to GND controls the full-scale current in each LED string: ILEDmax = 20mA x 100k/RISET The acceptable resistance range is 74k < RISET < 133k, which corresponds to full-scale LED current of 27mA > ILEDmax > 15mA. Connect ISET to VCC for a default full-scale LED current of 20mA. 19 FSET PLL Free-Running Frequency Control Pin. The resistance from FSET to GND controls the PLL oscillator's free-running frequency, fPLL: fPLL = 1 / (10 x RFSET x 800pF) The capture range is 0.6 x fPLL to fPLL. The acceptable resistance range for FSET is 250k < RFSET < 754k, which corresponds to a frequency range of 500Hz > fPLL > 166Hz. The resulting capture frequency range is 100Hz to 500Hz. 20 CPLL Phase-Locked Loop-Compensation Capacitor Pin. The capacitance at CPLL compensates the PLL loop response. Connect a 0.1F ceramic capacitor from CPLL to GND. EP EP 14 18 FUNCTION Exposed Backside Pad. Solder to the circuit board ground plane with sufficient copper connection to ensure low thermal resistance. See the PCB Layout Guidelines section. _______________________________________________________________________________________ 9 MAX8790A Pin Description (continued) MAX8790A Six-String White LED Driver with Active Current Balancing for LCD Panel Applications Detailed Description are directly turned on and off by the PWM signal. In analog dimming mode, an internal PLL, digital comparator, and DAC circuit translate the PWM signal into an analog signal that linearly controls the LED current, down to a PWM duty factor of 12.5%. The MAX8790A has multiple features to protect the controller from fault conditions. Separate feedback loops limit the output voltage if one or more LEDs fail open or short. During operation, if one of the feedback string voltages exceeds the VCC to 0.6V (typ) protection threshold, the controller shuts down and latches off after an internal timer expires. The controller features cycle-by-cycle current limit to provide consistent operation and soft-start capability. A thermal-shutdown circuit provides another level of protection. The MAX8790A includes a 5V linear regulator that provides the internal bias and gate drive for the step-up controller. When an external 5V is available, the internal LDO can be overdriven to decrease power dissipation. Otherwise, connect the IN pin to an input greater than 5.5V. The internal LDO is disabled when SHDN is low. The MAX8790A is a high-efficiency driver for arrays of white LEDs. It contains a fixed-frequency, currentmode, PWM step-up controller, 5V linear regulator, dimming control circuit, and six regulated current sources (see Figure 2). When enabled, the step-up controller boosts the output voltage to provide sufficient headroom for the current sources to regulate their respective string currents. The MAX8790A features selectable switching frequency (500kHz, 750kHz, or 1MHz), which allows trade-offs between external component size and operating efficiency. The control architecture automatically skips pulses at light loads to improve efficiency and prevents overcharging the output capacitor. A PWM logic input signal, BRT, controls the LED brightness. The MAX8790A supports both analog and digital control of the LED current, and achieves 100:1 dimming range. The MAX8790A's dimming control circuit consists of a PLL, a digital comparator, and a DAC. In direct DPWM mode, the step-up controller and current source L1 4.7H VIN 7V TO 21V D1 CIN VOUT UP TO 35V COUT 0.1F IN SHDN VCC ENA ISET 1F EXT CS RS 56m BRT GND FSET 511k N.C. N1 R1 1M OSC OV 1.2k CCV MAX8790A R2 37.4k 0.1F FB1 CPLL 0.1F FB2 FB3 FB4 EP FB5 FB6 Figure 1. Typical Operating Circuit 10 ______________________________________________________________________________________ Six-String White LED Driver with Active Current Balancing for LCD Panel Applications IN 1.25V ERROR COMPARATOR 5V LINEAR REGULATOR VCC MAX8790A OUTPUT OVERVOLTAGE COMPARATOR OV CLOCK CONTROL AND DRIVER LOGIC EXT CURRENT SENSE CS VCC SLOPE COMPENSATION OSCILLATOR FB OVERVOLTAGE COMPARATOR VCC + 0.6V TRI-LEVEL COMPARATOR OSC 65ms TIMER SHUTDOWN LATCH FB6 HVC FB5 SHDN FB4 ERROR AMPLIFIER LVC FB3 gm CCV ISET REF ADJ FSET OSC 256 x fBRT FB2 SAT REF FB1 CLK 8-BIT DAC N EN 8 VCC - 0.4V 10 DIGITAL CONTROL CURRENT SOURCE 8 CPLL PLL 8-BIT COUNTER 8 GND CURRENT SOURCE FB2 CURRENT SOURCE FB3 CURRENT SOURCE FB4 CURRENT SOURCE FB5 CURRENT SOURCE FB6 8-BIT LATCH 5 MSBs 5 LSBs DIGITAL COMPARATOR BRT ENA Figure 2. Control Circuit Block Diagram ______________________________________________________________________________________ 11 MAX8790A Six-String White LED Driver with Active Current Balancing for LCD Panel Applications Fixed-Frequency Step-Up Controller The MAX8790A's fixed-frequency, current-mode, stepup controller automatically chooses the lowest active FB_ voltage to regulate the feedback voltage. Specifically, the difference between the lowest FB_ voltage and the current source-control signal plus an offset (VSAT) is integrated at the CCV output. The resulting error signal is compared to the external switch current plus slope compensation to terminate the switch ontime. As the load changes, the error amplifier sources or sinks current to the CCV output to adjust the required peak inductor current. The slope-compensation signal is added to the current-sense signal to improve stability at high duty cycles. At light loads, the MAX8790A automatically skips pulses to improve efficiency and prevent overcharging the output capacitor. In SKIP mode, the inductor current ramps up for a minimum on-time of approximately 150ns, then discharges the stored energy to the output. The switch remains off until another pulse is needed to boost the output voltage. Internal 5V Linear Regulator VCC and UVLO The MAX8790A includes an internal low-dropout linear regulator (V CC ). When V IN is higher than 5.5V and SHDN is high, this linear regulator generates a 5V supply to power an internal PWM controller, control logic, and MOSFET driver. This linear regulator can deliver at least 10mA of total additional load current. If VIN is less than or equal to 5.5V, VCC and IN can be connected together and powered from an external 5V supply. There is an internal diode from VCC to IN, so VIN must be greater than VCC (see Figure 2). The MAX8790A includes UVLO protection. The controller is disabled until VCC exceeds the UVLO threshold of 4.25V (typ). Hysteresis on UVLO is approximately 20mV. The VCC pin should be bypassed to GND with a 1F or greater ceramic capacitor. L1 0.9H VIN 2.8V TO 5.5V D1 CIN COUT SHDN EXTERNAL 5V SUPPLY 1F IN VCC ENA ISET EXT RS 30m BRT N.C. N1 CS GND FSET 511k VOUT UP TO 22V R1 1M OSC OV 1.2k CCV MAX8790A R2 59k 0.1F FB1 CPLL 0.1F FB2 FB3 FB4 EP FB5 FB6 Figure 3. Low-Input-Voltage Application Circuit 12 ______________________________________________________________________________________ Six-String White LED Driver with Active Current Balancing for LCD Panel Applications Shutdown When the SHDN pin is less than 0.8V, the MAX8790A shuts down the internal LDO, the reference, current sources, and all control circuitry. The resulting supply current is less than 10A. While the n-channel MOSFET is turned off, the step-up regulator's output is connected to IN through the external inductor and rectifier diode. Frequency Selection A tri-level OSC input sets the internal oscillator frequency for the step-up converter, as shown in Table 1. High-frequency (1MHz) operation optimizes the regulator for the smallest component size, at the expense of efficiency due to increased switching losses. Low-frequency (500kHz) operation offers the best overall efficiency, but requires larger components and PCB area. Table 1. Frequency Selection OSC SWITCHING FREQUENCY (kHz) GND 500 Open 750 VCC 1000 Overvoltage Protection To protect the step-up converter when the load is open, or the output voltage becomes excessive for any reason, the MAX8790A features a dedicated overvoltage feedback input (OV). The OV pin is connected to the center tap of a resistive voltage-divider from the highvoltage output (see Figure 1). When the MAX8790A is powered up, if none of the LED strings on FB1-FB6 are connected to the step-up converter output, the step-up converter regulates the output voltage to V OUT = 1.23V(1 + R1 / R2). When VOV exceeds 1.23V, a comparator turns off N1. The step-up converter switch is reenabled after the output voltage drops below the protection threshold. The MAX8790A is equipped with a bank of six matched current sources. These specialized current sources are accurate to within 1.5% and can be switched on and off within 10s, enabling PWM frequencies of up to 2kHz. All LED full-scale currents are identical and are set through the ISET pin (15mA < ILED < 27mA). The minimum voltage drop across each current source is approximately 450mV at 20mA. The low voltage drop helps reduce dissipation while maintaining sufficient compliance to control the LED current within the required tolerances. The LED current sources can be disabled by grounding the respective FB_ pin at startup. When the IC is powered up, the controller scans settings for all FB_ pins. If an FB_ pin is not grounded, an internal circuit pulls this pin high, and the controller enables the corresponding current source to regulate the string current. If the FB_ pin is grounded, the controller disables the corresponding current regulator. The current regulator cannot be disabled by grounding any of the FB_ pins after the IC is powered up. All FB_ pins in use are measured and the highest signal (HVC) and the lowest signal (LVC) are extracted for two feedback loops. HVC is used to identify excessive dissipation across the current-source inputs. When HVC is greater than VCC + 0.6V (typ) for greater than 65ms (see the Current-Source Fault Protection section), a fault latch is set and the MAX8790A is shut down. The LDO output is not affected by the fault latch. LVC is fed into the step-up converter's error amplifier to regulate the step-up converter's output voltage. Current-Source Fault Protection The LED current sources are protected against string open, short, and gross mismatch faults, using overvoltage detection circuitry on each FB_ pin. If any of these three fault conditions persists for a preset duration, the MAX8790A is latched off. The duration of the fault time depends on the dimming mode and the duty cycle of the BRT input (DBRT). In the DPWM mode, the timeout interval is: LED Current Sources t TIMEOUT_DPWM = 65ms/DBRT In analog dimming mode, the fault time is fixed at 65ms for DBRT greater than 12.5%. When DBRT is less than 12.5%, the timeout interval is: t TIMEOUT_ANALOG = 8.125ms/DBRT Maintaining uniform LED brightness and dimming capability are critical for LCD backlight applications. The fault latch can be cleared by cycling the power or toggling the shutdown pin SHDN. ______________________________________________________________________________________ 13 MAX8790A Startup At startup, the MAX8790A checks each FB_ pin to determine if the respective current string is enabled. Each FB_ pin is internally pulled up with a 180A current source. If an FB_ pin is connected to GND, the corresponding string current source is disabled. This feedback scan takes approximately 4.2ms, after which the step-up converter begins switching. MAX8790A Six-String White LED Driver with Active Current Balancing for LCD Panel Applications Open-Current Source Protection The MAX8790A step-up converter output voltage is regulated according to the minimum value of the enable FB_ voltages. If an individual LED string is open, the respective FB_ is pulled down to near ground. In this situation, the step-up converter output voltage increases but is clamped to a level set with the OV feedback input. When this elevated output voltage is applied to the undamaged strings, excessive voltage drop develops across the FB_ pins. If the resulting HVC signal exceeds VCC + 0.6V for greater than 65ms, the fault latch is triggered to protect the circuit. LED-Short and String Mismatch Protection Normally, white LEDs have variations in forward-voltage drop of 3.1V to 3.6V. The MAX8790A can tolerate slight mismatches between LED strings. When the sum of the LED forward voltages creates a mismatch in the strings so the HVC signal exceeds VCC + 0.6V for greater than 65ms, the fault latch is triggered in much the same way as the circuit responds to open string faults. Similar protection is activated when an LED is shorted. The larger the number of series-connected LEDs (N), the smaller the tolerable mismatch between LEDs: Error < VCC + 0.6V - VSAT N VSAT 450mV and VCC = 5V Error < 5.150V N D = 50% BRT 5.150V N For N = 8, the average error per LED = 644mV. For N = 10, the average error per LED = 510mV. The larger the total mismatch, the larger the voltage drop required across each current source to correct for the error, and therefore the larger the dissipation within the MAX8790A. Dimming Control The MAX8790A features both analog and digital dimming control. Analog dimming can provide potentially higher converter efficiency because of low voltage drop across each WLED when the current is low. Digital dimming (DPWM) provides less WLED color distortion since the WLED current is held at full scale when the WLED is on. The MAX8790A's dimming control circuit consists of a PLL, a digital comparator, and a DAC. The controller provides 100:1 dimming range through either analog or digital control methods. Both methods translate the duty cycle of the BRT input into a control signal for the LED current sources. In analog dimming mode, the current-source outputs are DC and the BRT duty cycle (12.5% < DBRT < 100%) modulates the amplitude of the currents. For DBRT < 12.5%, the LED current is digitally modulated to reduce the average LED current down to 1% of full scale. The PLL detects the BRT frequency and phase, and adjusts the current-source amplitude and duty cycle synchronously (see Figure 4). ANALOG DIMMING MODE tON tBRT D= Average Error Per LED = D = 30% D = 12.5% D = 6.25% tON tBRT ILEDMAX ILED 0A Figure 4. LED Current Control Using Analog Dimming Mode 14 ______________________________________________________________________________________ Six-String White LED Driver with Active Current Balancing for LCD Panel Applications ILEDmax = 20mA x 100k RISET The acceptable resistance range is 74k < RISET < 133k, which corresponds to full-scale LED current of 27mA > ILEDmax > 15mA. Connect ISET to VCC for a default full-scale LED current of 20mA. When ENA is high, the analog dimming is enabled, when ENA is low, digital dimming is enabled. When the current-source output is pulse-width modulated, current-source turn-on is synchronized with the BRT signal. Synchronization and low jitter in the PWM signals help reduce flicker noise in the display. The current through each FB_ pin is controlled only during the D= step-up converter's on-time. During the converter's offtime, the current sources are turned off. The output voltage does not discharge and stays high. Each FB_ pin can withstand 28V, which is the pin's maximum rated voltage. Table 2 summarizes the characteristics of both analog and digital dimming methods. A PLL translates the duty cycle of the BRT input into a reference for the MAX8790A's current sources. A resistor from the FSET pin to ground controls the PLL's freerunning frequency: 1 fPLL = 10 x RFSET x 800pF The PLL's loop filter bandwidth is set with a capacitor from the CPLL pin to ground. This filter integrates the phase difference between the BRT input signal and the PLL oscillator. The filter bandwidth determines the PLL's dynamic response to frequency changes in the BRT signal. For most applications, a 0.1F capacitor is adequate for oscillator frequencies in the 166Hz < fPLL < 500Hz range. The PLL frequency capture window is 0.6 x fPLL to fPLL. DPWM DIMMING MODE tON tBRT D = 6.25% D = 12.5% D = 30% D = 50% tON BRT tBRT ILEDMAX ILED 0A Figure 5. LED Current Control Using DPWM Dimming Mode Table 2. Dimming Mode MODE ENA PLL FREQUENCY CPLL DESCRIPTION Analog + DPWM > 2.1V 250k < RFSET < 754k 0.1F Analog dimming from 100% to 12.5% brightness. From 12.5% to 1% brightness, DPWM dimming is employed. BRT frequency range is 100Hz to 500Hz. Direct DPWM < 0.8V VFSET > VCC - 0.4V, disables PLL OPEN Direct dimming by BRT signal. BRT frequency can be 100Hz to 2kHz; 50s minimum BRT on-time limits the minimum brightness. ______________________________________________________________________________________ 15 MAX8790A In digital dimming mode, the step-up controller and current source are directly turned on and off by the PWM signal. The current pulse magnitude, or full-scale current, is set by ISET and is independent of PWM duty factor. The current-source outputs are PWM signals synchronized to the BRT input signal (see Figure 5). The full-scale current in both methods is specified by resistance from the ISET pin to ground: MAX8790A Six-String White LED Driver with Active Current Balancing for LCD Panel Applications The PLL is disabled in DPWM mode; consequently, the BRT frequency is not limited by fPLL. The maximum BRT frequency is determined by the minimum BRT ontime of 50s and the minimum acceptable dimming factor. If a 1% dimming factor is needed, the maximum BRT frequency is 200Hz. If a 10% dimming factor is acceptable, the maximum BRT frequency is 2kHz. In analog dimming mode, load-current transients can occur when the BRT frequency abruptly changes on the fly. Large regulation transients induce a flash on the LED load that is observable with the naked eye and should therefore be avoided. Such annoying flashes can be eliminated by dynamically changing the ENA pin setting. When a capacitor is connected to the CPLL pin and the ENA pin is grounded, the PLL continues to run but does not affect the dimming. When fast PLL lockup transitions are required, the ENA pin can be momentarily pulled to ground; after the PLL is locked up, ENA can be pulled high to reenable PLL in dimming control. Thermal Shutdown The MAX8790A includes a thermal-protection circuit. When the local IC temperature exceeds +170C (typ), the controller and current sources shut down and do not restart until the die temperature drops by 15C. Design Procedure All MAX8790A designs should be prototyped and tested prior to production. Table 3 provides a list of power components for the typical applications circuit. Table 4 lists component suppliers. External component value choice is primarily dictated by the output voltage and the maximum load current, as well as maximum and minimum input voltages. Begin by selecting an inductor value. Once L is known, choose the diode and capacitors. Table 3. Component List CIRCUIT FIGURE 1 FIGURE 1 FIGURE 1 FIGURE 3 Switching Frequency 1MHz 750kHz 500kHz 750kHz White LED 3.2V (typ), 3.5V (max) at 20mA Nichia NSSW008C 3.2V (typ), 3.5V (max) at 20mA Nichia NSSW008C 3.2V (typ), 3.5V (max) at 20mA Nichia NSSW008C 3.2V (typ), 3.5V (max) at 20mA Nichia NSSW008C Number of White LEDs 6 series x 6 parallel, 20mA (max) 8 series x 6 parallel, 20mA (max) 10 series x 6 parallel, 25mA (max) 6 series x 6 parallel, 20mA (max) Input Voltage 4.5V to 5.5V, VCC = IN 7V to 21V 7V to 21V 2.8V to 5.5V, VCC = 5V 4.7H, 2.05A power inductor Sumida CDRH5D16-4R7 4.7H, 3.6A power inductor Sumida CDRH8D28-4R7 0.9H, 4.7A power inductor Sumida CDRH5D16-0R9 Inductor L1 2.2H, 2.5A power inductor Sumida CDRH5D16-2R2 Input Capacitors 10F 10%, 10V X5R 10F 10%, 25V X5R 10F 10%, 25V X5R ceramic capacitor (1206) ceramic capacitor (1206) ceramic capacitor (1206) Murata GRM31MR61A106K Murata GRM31CR61E106KA Murata GRM31CR61E106KA COUT Output Capacitor 2.2F 10%, 50V X7R ceramic capacitor (1x) Murata GRM31CR71H225K MOSFET N1 60V, 2.8A n-channel MOSFET (6-pin TSOP) 30V, 3A n-channel MOSFET Fairchild Semiconductor (6-pin SC70) FDC5612 Vishay Si1402DH Sanyo Semiconductor CPH6424 Diode Rectifier D1 2A, 30V Schottky diode Nihon EC21QS03L Sense Resistor 50m 1%, 1/2W IRC LRC-LRF-1206LF-01R050-F 16 10F 10%, 10V X5R ceramic capacitor (1206) Murata GRM31MR61A106K 4.7F 10%, 50V X7R ceramic capacitor (1210) (1x) Murata GRM32ER71H475K 2.2F 10%, 50V X7R ceramic capacitor (1x) Murata GRM31CR71H225K 60V, 6A n-channel MOSFET (PowerPAK 1212-8) Vishay Si7308DN 30V, 4.9A n-channel MOSFET (6-pin TSOP) Vishay Si3456BDV 2A, 40V Schottky diode Toshiba CMS11 Nihon EC21QS04 3A, 60V Schottky diode Nihon EC31QS06 3A, 30V Schottky diode Nihon EC31QS03L 56m 1%, 1/2W IRC LRC-LRF-1206LF-01R056-F 40m 1%, 1/2W IRC LRC-LRF-1206LF-01R040-F 30m 1%, 1/2W IRC LRC-LRF-1206LF-01R030-F 2.2F 10%, 50V X7R ceramic capacitor (1206) (1x) Murata GRM31CR71H225K ______________________________________________________________________________________ Six-String White LED Driver with Active Current Balancing for LCD Panel Applications SUPPLIER PHONE WEBSITE Murata 770-436-1300 www.murata.com Nichia 248-352-6575 www.nichia.com Sumida 847-545-6700 www.sumida.com Toshiba 949-455-2000 www.toshiba.com/taec Vishay 203-268-6261 www.vishay.com Inductor Selection The inductance, peak current rating, series resistance, and physical size should all be considered when selecting an inductor. These factors affect the converter's operating mode, efficiency, maximum output load capability, transient response time, output voltage ripple, and cost. The maximum output current, input voltage, output voltage, and switching frequency determine the inductor value. Very high inductance minimizes the current ripple, and therefore reduces the peak current, which decreases core losses in the inductor and I2R losses in the entire power path. However, large inductor values also require more energy storage and more turns of wire, which increases physical size and I2R copper losses in the inductor. Low inductor values decrease the physical size, but increase the current ripple and peak current. Finding the best inductor involves the compromises among circuit efficiency, inductor size, and cost. When choosing an inductor, the first step is to determine the operating mode: continuous conduction mode (CCM) or discontinuous conduction mode (DCM). The MAX8790A has a fixed internal slope compensation, which requires a minimum inductor value. When CCM mode is chosen, the ripple current and the peak current of the inductor can be minimized. If a small-size inductor is required, DCM mode can be chosen. In DCM mode, the inductor value and size can be minimized but the inductor ripple current and peak current are higher than those in CCM. The controller can be stable, independent of the internal slope compensation mode, but there is a maximum inductor value requirement to ensure the DCM operating mode. The equations used here include a constant LIR, which is the ratio of the inductor peak-to-peak ripple current to the average DC inductor current at the full-load current. The controller operates in DCM mode when LIR is higher than 2.0, and it switches to CCM mode when LIR is lower than 2.0. The best trade-off between inductor size and converter efficiency for step-up regulators generally has an LIR between 0.3 and 0.5. However, depending on the AC characteristics of the inductor core material and ratio of inductor resistance to other power-path resistances, the best LIR can shift up or down. If the inductor resistance is relatively high, more ripple can be accepted to reduce the number of required turns and increase the wire diameter. If the inductor resistance is relatively low, increasing inductance to lower the peak current can reduce losses throughout the power path. If extremely thin high-resistance inductors are used, as is common for LCD panel applications, LIR higher than 2.0 can be chosen for DCM operating mode. Once a physical inductor is chosen, higher and lower values of the inductor should be evaluated for efficiency improvements in typical operating regions. The detail design procedure can be described as follows: Calculate the approximate inductor value using the typical input voltage (VIN), the maximum output current (IOUT(MAX)), the expected efficiency (TYP) taken from an appropriate curve in the Typical Operating Characteristics, and an estimate of LIR based on the above discussion: 2 VIN _ MIN VOUT - VIN _ MIN TYP L= VOUT IOUT(MAX) x fOSC LIR The MAX8790A has a minimum inductor value limitation for stable operation in CCM mode at low input voltage because of the internal fixed slope compensation. The minimum inductor value for stability is calculated by the following equation: L CCM(MIN) = (VOUT(MAX) + VDIODE - 2 x VIN(MIN) ) x RS 51mV x fOSC(MIN) where 51mV is a scale factor based on slope compensation, and RS is the current-sense resistor. To determine the minimum inductor value, the R S can be temporarily calculated using the following equation: RS _ TMP = 100mV 1.2 x IIN(DCMAX , ) where 100mV is the current-limit sense voltage. ______________________________________________________________________________________ 17 MAX8790A Table 4. Component Suppliers MAX8790A Six-String White LED Driver with Active Current Balancing for LCD Panel Applications The minimum inductor value should be recalculated after the R S is determined (see the Sense-Resistor Selection section). Choose an available inductor value from an appropriate inductor family. Calculate the maximum DC input current at the minimum input voltage VIN(MIN), using conservation of energy and the expected efficiency at that operating point (MIN) taken from an appropriate curve in the Typical Operating Characteristics: IIN(DCMAX , )= IOUT(MAX) x VOUT VIN(MIN) x MIN Calculate the ripple current at that operating point and the peak current required for the inductor: IRIPPLE = VIN(MIN) x (VOUT(MAX) - VIN(MIN) ) L x VOUT(MAX) x fOSC IRIPPLE IPEAK = IIN(DCMAX , )+ 2 When DCM operating mode is chosen to minimize the inductor value, the calculations are different from that in the above CCM mode. The maximum inductor value for DCM mode is calculated by the following equation: VIN(MIN) LDCM(MAX) = 1 - x VOUT(MAX) + VDIODE VIN(MIN)2 x 2 x fOSC(MAX) x VOUT(MAX) x IOUT(MAX) 7V LDCM(MAX) = 1 - x 28.72V + 0.4V (7V)2 x 0.9 = 5.8H 2 x 0.825MHz x 28.72V x 120mA An inductance less than LDCM(MAX) is required, so a 4.7H inductor is chosen. The peak inductor current at minimum input voltage is calculated as follows: IPEAK = 120mA x 2 x 28.72V x (28.72V + 0.4V - 7V ) 4.7H x 0.675MHz x 0.9 x (28.72V + 0.4V ) Sense-Resistor Selection The detected signal is fed into the step-up converter control compensation loop through the CS pin. The MAX8790A's current-mode step-up converter senses the switch current from CS to GND with an external resistor, RS. The current-limit sense voltage is a fixed 100mV. The required resistance is calculated based upon the peak inductor current at the end of the switch on-time: RS < VCS _ EC + 25.6mV x (0.75 - DMAX ) IOUT(max) x 2 x VOUT(MAX) x (VOUT(MAX) + VDIODE - VIN(MIN) ) L x fOSC(MIN) x x (VOUT(MAX) + VDIODE ) The inductor's saturation current rating should exceed I PEAK and the inductor's DC current rating should exceed IIN(DC,MAX). For good efficiency, choose an inductor with less than 0.1 series resistance. Considering the typical operating circuit, the maximum load current (IOUT(MAX)) is 120mA with a 28.72V output and a minimal input voltage of 7V. Choosing a DCM operating mode and estimating efficiency of 90% at this operating point: 18 IPEAK where 25.6mV is a scale factor from slope compensation, VCS_EC is the current-sense voltage listed in the Electrical Characteristics table (85mV), and the DMAX is the maximum duty cycle at minimum input voltage and maximum output voltage. In DCM operating mode, it is calculated by the following equation: The peak inductor current in DCM mode is calculated using the following equation: IPEAK = = 1.35A DMAX = L x ILIM x fOSC VIN(MIN) For the typical operating circuit as Figure 1: DMAX = RS < 4.7H x 1.35A x 0.75MHz = 0.68 7V 85mV + 25.6mV x (0.75 - 0.68) 1.35A = 64m Again, RS is calculated as a maximum, so a 56m current-sense resistor is chosen. ______________________________________________________________________________________ Six-String White LED Driver with Active Current Balancing for LCD Panel Applications VRIPPLE = VRIPPLE(C) + VRIPPLE(ESR) IOUT(MAX) VOUT(MAX) - VIN(MIN) VRIPPLE(C) COUT VOUT(MAX)fOSC and: VRIPPLE(ESR) IPEAKRESR(COUT) where I PEAK is the peak inductor current (see the Inductor Selection section). The output voltage-ripple voltage should be low enough for the FB_ current-source regulation. The ripple voltage should be less than 200mVP-P. For ceramic capacitors, the output-voltage ripple is typically dominated by VRIPPLE(C). The voltage rating and temperature characteristics of the output capacitor must also be considered. External MOSFET Selection The MAX8790A's step-up converter uses an external MOSFET to enable applications with scalable output voltage and output power. The boost switching architecture is simple and ensures that the controller is never exposed to high voltage. Only the external MOSFET, diode, and inductor are exposed to the output voltage plus one Schottky diode forward voltage: VBV = N x VF _ LED + VF _ SCHOTTKY + VFB _ The MOSFET's breakdown ratings should be higher than VBV with sufficient margin to ensure long-term reliability. A conservative rule of thumb, a minimum 30% margin would be recommended for MOSFET breakdown voltage. The external MOSFET should have a current rating of no less than the IPEAK derived from the Inductor Selection section. To improve efficiency, choose a MOSFET with low RDS(ON). The MAX8790A's gate-drive linear regulator can provide 10mA. Select the external MOSFET with a total gate charge so the average current to drive the MOSFET at maximum switching frequency is less than 10mA: Qg(MAX) x fOSC <10mA For example, the Si3458DV is specified with 16nC of max total gate charge at Vg = 10V. For 5V of gate drive, the required gate charge is 8nC, which equates to 8mA at 1MHz. The MOSFET conduction loss or resistive loss is caused by the MOSFET's on-resistance (RDS(ON)). This power loss can be estimated as: PDRES(MAX) = RDS(ON) x L x fOSC x IPEAK 3 3 x VIN(MIN) For the above Si3458DV, the estimated conduction loss is: PDRES(MAX) = 0.1 x 4.7H x 750kHz x 1.35A 3 = 0.04W 3 x 7V The approximate maximum switching loss can be calculated as: t xI x VOUT x fOSC PDSW(MAX) = turn-off PEAK 2 For the above Si3458DV, the approximate switching loss is: PDSW(MAX) = 10ns x 1.35A x 28.72V x 750kHz = 0.145W 2 Rectifier Diode Selection The MAX8790A's high switching frequency demands a high-speed rectifier. Schottky diodes are recommended for most applications because of their fast recovery time and low forward voltage. The diode should be rated to handle the output voltage and the peak switch current. Make sure that the diode's peak current rating is at least IPEAK calculated in the Inductor Selection section and that its breakdown voltage exceeds the output voltage. Setting the Overvoltage Protection Limit The OV protection circuit should ensure the circuit safe operation; therefore, the controller should limit the output voltage within the ratings of all MOSFET, diode, and output capacitor components, while providing sufficient output voltage for LED current regulation. The OV pin is connected to the center tap of a resistive voltagedivider (R1 and R2 in Figure 1) from the high-voltage output. When the controller detects the OV pin voltage reaching the threshold VOV_TH, typically 1.23V, OV protection is activated. Hence, the step-up converter output overvoltage protection point is: VOUT(OVP) = VOV _ TH x (1 + R1 ) R2 In Figure 1, the output OVP voltage is set to: VOUT(OVP) = 1.23V x (1 + 1 M ) = 34.1V 37.4k ______________________________________________________________________________________ 19 MAX8790A Output Capacitor Selection The total output voltage ripple has two components: the capacitive ripple caused by the charging and discharging on the output capacitor, and the ohmic ripple due to the capacitor's equivalent series resistance (ESR): MAX8790A Six-String White LED Driver with Active Current Balancing for LCD Panel Applications Input Capacitor Selection The input capacitor (CIN) filters the current peaks drawn from the input supply and reduces noise injection into the IC. A 10F ceramic capacitor is used in the typical operating circuit (Figure 1) because of the high source impedance seen in typical lab setups. Actual applications usually have much lower source impe-dance since the step-up regulator often runs directly from the output of another regulated supply. In some applications, CIN can be reduced below the values used in the typical operating circuit. Ensure a low noise supply at IN by using adequate CIN. Alternatively, greater voltage variation can be tolerated on CIN if IN is decoupled from CIN using an RC lowpass filter. Select CIN's RMS ripple current rating to ensure that its thermal rise is less than approximately 10C: IRMS = dIL 2x 3 LED Selection and Bias The series/parallel configuration of the LED load and the full-scale bias current have a significant effect on regulator performance. LED characteristics vary significantly from manufacturer to manufacturer. Consult the respective LED data sheets to determine the range of output voltages for a given brightness and LED current. In general, brightness increases as a function of bias current. This suggests that the number of LEDs could be decreased if higher bias current is chosen; however, high current increases LED temperature and reduces operating life. Improvements in LED technology are resulting in devices with lower forward voltage while increasing the bias current and light output. LED manufacturers specify LED color at a given LED current. With lower LED current, the color of the emitted light tends to shift toward the blue range of the spectrum. A blue bias is often acceptable for business applications but not for high-image-quality applications such as DVD players. Direct DPWM dimming is a viable solution for reducing power dissipation while maintaining LED color integrity. Careful attention should be paid to switching noise to avoid other display quality problems. 20 Using fewer LEDs in a string improves step-up converter efficiency, and lowers breakdown voltage requirements of the external MOSFET and diode. The minimum number of LEDs in series should always be greater than the maximum input voltage. If the diode voltage drop is lower than the maximum input voltage, the voltage drop across the current-sense inputs (FB_) increases and causes excess heating in the IC. Between 8 and 12 LEDs in series is ideal for input voltages up to 20V. Applications Information LED VFB_ Variation The MAX8790A has accurate (1.5%) matching for each current source. However, the forward voltage of each white LED can vary up to 5% from part to part. The accumulated voltage difference in each string equates to additional power loss within the IC. For the best efficiency, the voltage difference between strings should be minimized. The difference between lowest voltage string and highest voltage string should be less than 4.5V. Otherwise, the internal LED short-circuit protection shuts the part off. Choosing the Appropriate Dimming Mode Analog dimming mode allows lower peak LED current and results in higher converter efficiency and lower noise compared to direct DPWM mode. Unfortunately, the LED color spectrum can shift as a function of DC current so DPWM mode is often used to achieve more consistent display characteristics. (See the LED manufacturer's data sheet to determine the extent of the color shift.) When the MAX8790A is configured with an FSET resistor and CPLL capacitor, the ENA signal can toggle between modes on the fly. Care should be exercised when switching between modes to prevent the current from becoming unstable during the PLL lock-in time. To avoid such problems, force the controller into DPWM mode between transitions. LCD Panel Capacitance Some LCD panels include a capacitor in parallel with LED string to improve ESD immunity. The MAX8790A can start up without a problem for string capacitance up to 0.27F. ______________________________________________________________________________________ Six-String White LED Driver with Active Current Balancing for LCD Panel Applications 4) Place the overvoltage detection-divider resistors as close to the OV pin as possible. The divider's center trace should be kept short. Placing the resistors far away causes the sensing trace to become antennas that can pick up switching noise. Avoid running the sensing traces near LX. EXT CS FB6 TOP VIEW OV Pin Configuration 15 14 13 12 11 IN 16 10 FB5 CCV 17 9 FB4 8 GND FSET 19 7 FB3 CPLL 20 6 FB2 ISET 18 3 4 5 FB1 2 SHDN 1 BRT MAX8790AETP+ ENA 3) Create a ground island (PGND) consisting of the input and output capacitor ground and negative terminal of the current-sense resistor. Connect all these together with short, wide traces or a small ground plane. Maximizing the width of the power ground traces improves efficiency and reduces output-voltage ripple and noise spikes. Create an analog ground island (AGND) consisting of the overvoltage detection-divider ground connection, the ISET and FSET resistor connections, CCV and CPLL capacitor connections, and the device's exposed backside pad. Connect the AGND and PGND islands by connecting the GND pins directly to the exposed backside pad. Make no other connections between these separate ground planes. 7) Refer to the MAX8790A evaluation kit for an example of proper board layout. VCC 2) Connect high-current input and output components with short and wide connections. The high-current input loop goes from the positive terminal of the input capacitor to the inductor, to the external MOSFET, then to the current-sense resistor, and to the input capacitor's negative terminal. The high-current output loop is from the positive terminal of the input capacitor to the inductor, to the rectifier diode, to the positive terminal of the output capacitors, reconnecting between the output capacitor and input capacitor ground terminals. Avoid using vias in the high-current paths. If vias are unavoidable, use multiple vias in parallel to reduce resistance and inductance. 6) Minimize the size of the LX node while keeping it wide and short. Keep the LX node away from the feedback node and ground. If possible, avoid running the LX node from one side of the PCB to the other. Use DC traces as shields, if necessary. OSC 1) Minimize the area of the high current-switching loop of the rectifier diode, external MOSFET, sense resistor, and output capacitor to avoid excessive switching noise. Use wide and short traces for the gate-drive loop from the EXT pin, to the MOSFET gate, and through the current-sense resistor, then returning to the IC GND pin. 5) Place the IN pin bypass capacitor as close to the device as possible. The ground connection of the IN bypass capacitor should be connected directly to GND pins with a wide trace. 4mm x 4mm THIN QFN Chip Information TRANSISTOR COUNT: 12,042 PROCESS: BiCMOS ______________________________________________________________________________________ 21 MAX8790A PCB Layout Guidelines Careful PCB layout is important for proper operation. Use the following guidelines for good PCB layout: Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) 24L QFN THIN.EPS MAX8790A Six-String White LED Driver with Active Current Balancing for LCD Panel Applications 22 ______________________________________________________________________________________ Six-String White LED Driver with Active Current Balancing for LCD Panel Applications Revision History Pages changed at Rev 1: All A added to all pages. Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 23 (c) 2007 Maxim Integrated Products is a registered trademark of Maxim Integrated Products, Inc. MAX8790A Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.)