© Semiconductor Components Industries, LLC, 2009
December, 2009 Rev. 21
1Publication Order Number:
MC34063A/D
MC34063A, MC33063A,
NCV33063A
1.5 A, Step-Up/Down/
Inverting Switching
Regulators
The MC34063A Series is a monolithic control circuit containing the
primary functions required for DCtoDC converters. These devices
consist of an internal temperature compensated reference, comparator,
controlled duty cycle oscillator with an active current limit circuit,
driver and high current output switch. This series was specifically
designed to be incorporated in StepDown and StepUp and
VoltageInverting applications with a minimum number of external
components. Refer to Application Notes AN920A/D and AN954/D
for additional design information.
Features
Operation from 3.0 V to 40 V Input
Low Standby Current
Current Limiting
Output Switch Current to 1.5 A
Output Voltage Adjustable
Frequency Operation to 100 kHz
Precision 2% Reference
PbFree Packages are Available
Figure 1. Representative Schematic Diagram
SQ
R
Q2
Q1
100
Ipk
Oscillator CT
Comparator
+
-
1.25 V
Reference
Regulator
1
2
3
45
6
7
8
Drive
Collector
Ipk
Sense
VCC
Comparator
Inverting
Input
Switch
Collector
Switch
Emitter
Timing
Capacitor
GND
(Bottom View)
This device contains 79 active transistors.
SOIC8
D SUFFIX
CASE 751
PDIP8
P, P1 SUFFIX
CASE 626
1
8
See detailed ordering and shipping information in the package
dimensions section on page 12 of this data sheet.
ORDERING INFORMATION
http://onsemi.com
x = 3 or 4
A = Assembly Location
L, WL = Wafer Lot
Y, YY = Year
W, WW = Work Week
G or G= PbFree Package
1
8
3x063AP1
AWL
YYWWG
1
8
33063AVP
AWL
YYWWG
MARKING
DIAGRAMS
1
8
3x063
ALYWA
G
1
8
3x063V
ALYWA
G
1
8
1
DFN8
CASE 488AF
33063
ALYWA
G
MC34063A, MC33063A, NCV33063A
http://onsemi.com
2
1
Switch
Collector
Switch
Emitter
Timing
Capacitor
GND
Driver
Collector
Ipk Sense
VCC
Comparator
Inverting
Input
(Top View)
2
3
45
6
7
8
Figure 2. Pin Connections
Ç
Ç
Ç
Ç
Ç
Ç
Ç
Ç
ÇÇ
ÇÇ
ÇÇ
ÇÇ
ÇÇ
ÇÇ
ÇÇ
ÇÇ
(Top View)
EP Flag
Switch Collector
Switch Emitter
Timing Capacitor
GND
Ipk Sense
Driver Collector
Comparator
Inverting Input
VCC
MAXIMUM RATINGS
Rating Symbol Value Unit
Power Supply Voltage VCC 40 Vdc
Comparator Input Voltage Range VIR 0.3 to +40 Vdc
Switch Collector Voltage VC(switch) 40 Vdc
Switch Emitter Voltage (VPin 1 = 40 V) VE(switch) 40 Vdc
Switch Collector to Emitter Voltage VCE(switch) 40 Vdc
Driver Collector Voltage VC(driver) 40 Vdc
Driver Collector Current (Note 1) IC(driver) 100 mA
Switch Current ISW 1.5 A
Power Dissipation and Thermal Characteristics
Plastic Package, P, P1 Suffix
TA = 25°C PD1.25 W
Thermal Resistance RqJA 115 °C/W
SOIC Package, D Suffix
TA = 25°C PD625 mW
Thermal Resistance RqJA 160 °C/W
DFN Package
TA = 25°C PD1.25 mW
Thermal Resistance RqJA 80 °C/W
Operating Junction Temperature TJ+150 °C
Operating Ambient Temperature Range TA°C
MC34063A 0 to +70
MC33063AV, NCV33063A 40 to +125
MC33063A 40 to + 85
Storage Temperature Range Tstg 65 to +150 °C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. Maximum package power dissipation limits must be observed.
2. This device series contains ESD protection and exceeds the following tests: Human Body Model 4000 V per MILSTD883, Method 3015.
Machine Model Method 400 V.
3. NCV prefix is for automotive and other applications requiring site and change control.
MC34063A, MC33063A, NCV33063A
http://onsemi.com
3
ELECTRICAL CHARACTERISTICS (VCC = 5.0 V, TA = Tlow to Thigh [Note 4], unless otherwise specified.)
Characteristics Symbol Min Typ Max Unit
OSCILLATOR
Frequency (VPin 5 = 0 V, CT = 1.0 nF, TA = 25°C) fosc 24 33 42 kHz
Charge Current (VCC = 5.0 V to 40 V, TA = 25°C) Ichg 24 35 42 mA
Discharge Current (VCC = 5.0 V to 40 V, TA = 25°C) Idischg 140 220 260 mA
Discharge to Charge Current Ratio (Pin 7 to VCC, TA = 25°C) Idischg/Ichg 5.2 6.5 7.5
Current Limit Sense Voltage (Ichg = Idischg, TA = 25°C) Vipk(sense) 250 300 350 mV
OUTPUT SWITCH (Note 5)
Saturation Voltage, Darlington Connection
(I
SW = 1.0 A, Pins 1, 8 connected)
VCE(sat) 1.0 1.3 V
Saturation Voltage (Note 6)
(ISW = 1.0 A, RPin 8 = 82 W to VCC, Forced b ] 20)
VCE(sat) 0.45 0.7 V
DC Current Gain (ISW = 1.0 A, VCE = 5.0 V, TA = 25°C) hFE 50 75
Collector OffState Current (VCE = 40 V) IC(off) 0.01 100 mA
COMPARATOR
Threshold Voltage
TA = 25°C
TA = Tlow to Thigh
Vth
1.225
1.21
1.25
1.275
1.29
V
Threshold Voltage Line Regulation (VCC = 3.0 V to 40 V)
MC33063, MC34063
MC33063V, NCV33063
Regline
1.4
1.4
5.0
6.0
mV
Input Bias Current (Vin = 0 V) IIB 20 400 nA
TOTAL DEVICE
Supply Current (VCC = 5.0 V to 40 V, CT = 1.0 nF, Pin 7 = VCC,
VPin 5 > Vth, Pin 2 = GND, remaining pins open)
ICC 4.0 mA
4. Tlow = 0°C for MC34063, 40°C for MC33063, MC33063V, NCV33063
Thigh = +70°C for MC34063, +85°C for MC33063, +125°C for MC33063V, NCV33063
5. Low duty cycle pulse techniques are used during test to maintain junction temperature as close to ambient temperature as possible.
6. If the output switch is driven into hard saturation (nonDarlington configuration) at low switch currents ( 300 mA) and high driver currents
(30 mA), it may take up to 2.0 ms for it to come out of saturation. This condition will shorten the off time at frequencies 30 kHz, and is
magnified at high temperatures. This condition does not occur with a Darlington configuration, since the output switch cannot saturate. If a
nonDarlington configuration is used, the following output drive condition is recommended:
Forced bof output switch : ICoutput
ICdriver 7.0 mA * w10
* The 100 W resistor in the emitter of the driver device requires about 7.0 mA before the output switch conducts.
MC34063A, MC33063A, NCV33063A
http://onsemi.com
4
0
2
4
6
8
10
12
14
16
18
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
0
20
40
60
80
100
120
140
160
180
Figure 3. Oscillator Frequency
VCC = 5.0 V, Pin 7 = VCC
Pin 5 = GND, TA = 25°C
Ct, TIMING CAPACITOR CAPACITANCE (nF)
OFF TIME (ms)
ON TIME (ms), FREQUENCY (kHz)
ON TIME (ms)
OFF TIME (ms)
FREQUENCY (kHz)
VCC = 5.0 V
Pin 7 = VCC
Pin 2 = GND
Pins 1, 5, 8 = Open
CT = 1.0 nF
TA = 25°C
Figure 4. Timing Capacitor Waveform
10 ms/DIV
, OSCILLATOR VOLTAGE (V)
OSC
200 mV/DIV
V
Figure 5. Emitter Follower Configuration Output
Saturation Voltage versus Emitter Current
Figure 6. Common Emitter Configuration Output
Switch Saturation Voltage versus
Collector Current
Figure 7. Current Limit Sense Voltage
versus Temperature
Figure 8. Standby Supply Current versus
Supply Voltage
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6
, SATURATION VOLTAGE (V)
CE(sat)
IE, EMITTER CURRENT (A)
V
VCC = 5.0 V
Pins 1, 7, 8 = VCC
Pins 3, 5 = GND
TA = 25°C
(See Note 7)
, SATURATION VOLTAGE (V)
CE(sat)
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6
IC, COLLECTOR CURRENT(A)
V
Darlington Connection
Forced b = 20
-55 -25 0 25 50 75 100 125
, CURRENT LIMIT SENSE VOLTAGE (V)
IPK(sense)
TA, AMBIENT TEMPERATURE (°C)
V
VCC = 5.0 V
Ichg = Idischg
0 5.0 10 15 20 25 30 35 40
, SUPPLY CURRENT (mA)
CC
VCC, SUPPLY VOLTAGE (V)
I
CT = 1.0 nF
Pin 7 = VCC
Pin 2 = GND
1.8
1.7
1.6
1.5
1.4
1.3
1.2
1.1
1.0
1.1
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
400
380
360
340
320
300
280
260
240
220
200
3.6
3.2
2.4
2.0
1.6
1.2
0.8
0.4
0
1.0
2.8
VCC = 5.0 V
Pin 7 = VCC
Pins 2, 3, 5 = GND
TA = 25°C
(See Note 7)
7. Low duty cycle pulse techniques are used during test to maintain junction temperature as close to ambient temperature as possible.
MC34063A, MC33063A, NCV33063A
http://onsemi.com
5
170 mH
L
8
180
7
Rsc
0.22
6
Vin
12 V
100
+
5
R1 2.2 k
R2
47 k
SQ
R
Q2
Q1
Ipk
OSC
CT
VCC
+
-Comp.
1.25 V
Ref
Reg
1
2
3
4
1N5819
CT
1500
pF
330 CO
+
Vout
28 V/175 mA Vout
1.0 mH
+100
Optional Filter
Test Conditions Results
Line Regulation Vin = 8.0 V to 16 V, IO = 175 mA 30 mV = ±0.05%
Load Regulation Vin = 12 V, IO = 75 mA to 175 mA 10 mV = ±0.017%
Output Ripple Vin = 12 V, IO = 175 mA 400 mVpp
Efficiency Vin = 12 V, IO = 175 mA 87.7%
Output Ripple With Optional Filter Vin = 12 V, IO = 175 mA 40 mVpp
Figure 9. StepUp Converter
MC34063A, MC33063A, NCV33063A
http://onsemi.com
6
9a. External NPN Switch 9b. External NPN Saturated Switch
(See Note 8)
8
7
6
Rsc
Vin
1
2
Vout R
R ³ 0 for
constant Vin
8. If the output switch is driven into hard saturation (nonDarlington configuration) at low switch currents ( 300 mA) and high driver currents
(30 mA), it may take up to 2.0 ms to come out of saturation. This condition will shorten the off time at frequencies 30 kHz, and is magnified
at high temperatures. This condition does not occur with a Darlington configuration, since the output switch cannot saturate. If a
nonDarlington configuration is used, the following output drive condition is recommended.
8
7
6
Rsc
Vin
1
2
Vout
Figure 10. External Current Boost Connections for IC Peak Greater than 1.5 A
MC34063A, MC33063A, NCV33063A
http://onsemi.com
7
1.25 V
Ref
Reg
Vout
5.0 V/500 mA
1.0 mH
Vout
+100
Optional Filter
8
7
Rsc
0.33
6
Vin
25 V
100 +
R1 1.2 k
R2
3.6 k
SQ
R
Q2
Q1
Ipk
OSC CT
VCC
+
-Comp.
1
2
3
4
CT
470
pF
470 CO
+
5
L
1N5819
220 mH
Test Conditions Results
Line Regulation Vin = 15 V to 25 V, IO = 500 mA 12 mV = ±0.12%
Load Regulation Vin = 25 V, IO = 50 mA to 500 mA 3.0 mV = ±0.03%
Output Ripple Vin = 25 V, IO = 500 mA 120 mVpp
Short Circuit Current Vin = 25 V, RL = 0.1 W1.1 A
Efficiency Vin = 25 V, IO = 500 mA 83.7%
Output Ripple With Optional Filter Vin = 25 V, IO = 500 mA 40 mVpp
Figure 11. StepDown Converter
11a. External NPN Switch 11b. External PNP Saturated Switch
8
7
6
Rsc
Vin
1
2
Vout
8
7
6
Rsc
Vin
1
2
V
Figure 12. External Current Boost Connections for IC Peak Greater than 1.5 A
MC34063A, MC33063A, NCV33063A
http://onsemi.com
8
1.25 V
Ref
Reg
Vout
-12 V/100 mA Vout
1.0 mH
+100
Optional Filter
8
7
Rsc
0.24
6
Vin
4.5 V to 6.0 V
100
+
5
R2 8.2 k
SQ
R
Q2
Q1
Ipk
OSC CT
Comp.
R1
953
1
2
3
4
+1500
pF
+
-
1N5819
1000 mf+
88 mH
VCC
CO
L
Test Conditions Results
Line Regulation Vin = 4.5 V to 6.0 V, IO = 100 mA 3.0 mV = ±0.012%
Load Regulation Vin = 5.0 V, IO = 10 mA to 100 mA 0.022 V = ±0.09%
Output Ripple Vin = 5.0 V, IO = 100 mA 500 mVpp
Short Circuit Current Vin = 5.0 V, RL = 0.1 W910 mA
Efficiency Vin = 5.0 V, IO = 100 mA 62.2%
Output Ripple With Optional Filter Vin = 5.0 V, IO = 100 mA 70 mVpp
Figure 13. Voltage Inverting Converter
13a. External NPN Switch 13b. External PNP Saturated Switch
8
7
6
Vin
1
2
Vout
8
7
6
Vin
1
2
Vout
Figure 14. External Current Boost Connections for IC Peak Greater than 1.5 A
3
4
+
3
4
+
MC34063A, MC33063A, NCV33063A
http://onsemi.com
9
Figure 15. Printed Circuit Board and Component Layout
(Circuits of Figures 9, 11, 13)
INDUCTOR DATA
Converter Inductance (mH) Turns/Wire
StepUp 170 38 Turns of #22 AWG
StepDown 220 48 Turns of #22 AWG
VoltageInverting 88 28 Turns of #22 AWG
All inductors are wound on Magnetics Inc. 55117 toroidal core.
MC34063A, MC33063A, NCV33063A
http://onsemi.com
10
Figure 16. Printed Circuit Board for DFN Device
MC34063A, MC33063A, NCV33063A
http://onsemi.com
11
Calculation StepUp StepDown VoltageInverting
ton/toff Vout )VF*Vin(min)
Vin(min) *Vsat
Vout )VF
Vin(min) *Vsat *Vout
|Vout|)VF
Vin *Vsat
(ton + toff)1
f
1
f
1
f
toff ton )toff
ton
toff )1
ton )toff
ton
toff )1
ton )toff
ton
toff )1
ton (ton + toff) toff (ton + toff) toff (ton + toff) toff
CT4.0 x 105 ton 4.0 x 105 ton 4.0 x 105 ton
Ipk(switch)
2Iout(max) ǒton
toff )1Ǔ2Iout(max) 2Iout(max) ǒton
toff )1Ǔ
Rsc 0.3/Ipk(switch) 0.3/Ipk(switch) 0.3/Ipk(switch)
L(min) ǒ(Vin(min) *Vsat)
Ipk(switch) Ǔton(max) ǒ(Vin(min) *Vsat *Vout)
Ipk(switch) Ǔton(max
)
ǒ(Vin(min) *Vsat)
Ipk(switch) Ǔton(max)
CO9Ioutton
Vripple(pp)
Ipk(switch)(ton )toff)
8Vripple(pp)
9Ioutton
Vripple(pp)
Vsat = Saturation voltage of the output switch.
VF = Forward voltage drop of the output rectifier.
The following power supply characteristics must be chosen:
Vin Nominal input voltage.
Vout Desired output voltage,
Iout Desired output current.
fmin Minimum desired output switching frequency at the selected values of Vin and IO.
Vripple(pp) Desired peaktopeak output ripple voltage. In practice, the calculated capacitor value will need to be increased due to its
equivalent series resistance and board layout. The ripple voltage should be kept to a low value since it will directly affect the
line and load regulation.
NOTE: For further information refer to Application Note AN920A/D and AN954/D.
|Vout|+1.25 ǒ1)R2
R1Ǔ
Figure 17. Design Formula Table
MC34063A, MC33063A, NCV33063A
http://onsemi.com
12
ORDERING INFORMATION
Device Package Shipping
MC33063AD SOIC898 Units / Rail
MC33063ADG SOIC8
(PbFree)
98 Units / Rail
MC33063ADR2 SOIC82500 Units / Tape & Reel
MC33063ADR2G SOIC8
(PbFree)
2500 Units / Tape & Reel
MC33063AP1 PDIP850 Units / Rail
MC33063AP1G PDIP8
(PbFree)
50 Units / Rail
MC33063AVD SOIC898 Units / Rail
MC33063AVDG SOIC8
(PbFree)
98 Units / Rail
MC33063AVDR2 SOIC8
2500 Units / Tape & Reel
MC33063AVDR2G SOIC8
(PbFree)
NCV33063AVDR2* SOIC8
NCV33063AVDR2G* SOIC8
(PbFree)
MC33063AVP PDIP850 Units / Rail
MC33063AVPG PDIP8
(PbFree)
50 Units / Rail
MC34063AD SOIC898 Units / Rail
MC34063ADG SOIC8
(PbFree)
98 Units / Rail
MC34063ADR2 SOIC82500 Units / Tape & Reel
MC34063ADR2G SOIC8
(PbFree)
2500 Units / Tape & Reel
MC34063AP1 PDIP850 Units / Rail
MC34063AP1G PDIP8
(PbFree)
50 Units / Rail
MC33063MNTXG DFN8
(PbFree)
4000 Units / Tape & Reel
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specification Brochure, BRD8011/D.
*NCV33063A: Tlow = 40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and
change control.
MC34063A, MC33063A, NCV33063A
http://onsemi.com
13
PACKAGE DIMENSIONS
SOIC8 NB
CASE 75107
ISSUE AJ
SEATING
PLANE
1
4
58
N
J
X 45 _
K
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. 75101 THRU 75106 ARE OBSOLETE. NEW
STANDARD IS 75107.
A
BS
D
H
C
0.10 (0.004)
DIM
A
MIN MAX MIN MAX
INCHES
4.80 5.00 0.189 0.197
MILLIMETERS
B3.80 4.00 0.150 0.157
C1.35 1.75 0.053 0.069
D0.33 0.51 0.013 0.020
G1.27 BSC 0.050 BSC
H0.10 0.25 0.004 0.010
J0.19 0.25 0.007 0.010
K0.40 1.27 0.016 0.050
M0 8 0 8
N0.25 0.50 0.010 0.020
S5.80 6.20 0.228 0.244
X
Y
G
M
Y
M
0.25 (0.010)
Z
Y
M
0.25 (0.010) ZSXS
M
____
1.52
0.060
7.0
0.275
0.6
0.024
1.270
0.050
4.0
0.155
ǒmm
inchesǓ
SCALE 6:1
*For additional information on our PbFree strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
SOLDERING FOOTPRINT*
MC34063A, MC33063A, NCV33063A
http://onsemi.com
14
PACKAGE DIMENSIONS
PDIP8
P, P1 SUFFIX
CASE 62605
ISSUE L
NOTES:
1. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
2. PACKAGE CONTOUR OPTIONAL (ROUND OR
SQUARE CORNERS).
3. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
14
58
F
NOTE 2 A
B
T
SEATING
PLANE
H
J
G
DK
N
C
L
M
M
A
M
0.13 (0.005) B M
T
DIM MIN MAX MIN MAX
INCHESMILLIMETERS
A9.40 10.16 0.370 0.400
B6.10 6.60 0.240 0.260
C3.94 4.45 0.155 0.175
D0.38 0.51 0.015 0.020
F1.02 1.78 0.040 0.070
G2.54 BSC 0.100 BSC
H0.76 1.27 0.030 0.050
J0.20 0.30 0.008 0.012
K2.92 3.43 0.115 0.135
L7.62 BSC 0.300 BSC
M--- 10 --- 10
N0.76 1.01 0.030 0.040
__
MC34063A, MC33063A, NCV33063A
http://onsemi.com
15
PACKAGE DIMENSIONS
ÉÉÉ
ÉÉÉ
ÉÉÉ
DFN8, 4x4
CASE 488AF01
ISSUE C
NOTES:
1. DIMENSIONS AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.15 AND 0.30MM FROM TERMINAL TIP.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
5. DETAILS A AND B SHOW OPTIONAL
CONSTRUCTIONS FOR TERMINALS.
DIM MIN MAX
MILLIMETERS
A0.80 1.00
A1 0.00 0.05
A3 0.20 REF
b0.25 0.35
D4.00 BSC
D2 1.91 2.21
E4.00 BSC
E2 2.09 2.39
e0.80 BSC
K0.20 −−−
L0.30 0.50
D
B
E
C0.15
A
C0.15
2X
2X
TOP VIEW
SIDE VIEW
BOTTOM VIEW
Ç
ÇÇ
Ç
Ç
ÇÇ
Ç
Ç
C
A
(A3)
A1
8X
SEATING
PLANE
C0.08
C0.10
Ç
Ç
ÇÇ
Ç
Ç
e
8X L
K
E2
D2
b
NOTE 3
14
58
8X
0.10 C
0.05 C
AB
PIN ONE
REFERENCE
*For additional information on our PbFree strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
SOLDERING FOOTPRINT*
8X
0.63
2.21
2.39
8X
0.80
PITCH
4.30
0.35
L1
DETAIL A
L
OPTIONAL
CONSTRUCTIONS
ÉÉ
ÇÇ
ÇÇ
A1
A3
L
ÇÇ
ÉÉ
DETAIL B
MOLD CMPDEXPOSED Cu
ALTERNATE
CONSTRUCTIONS
L1 −−− 0.15
DETAIL B
NOTE 4
DETAIL A
DIMENSIONS: MILLIMETERS
PACKAGE
OUTLINE
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
MC34063A/D
SENSEFET is a trademark of Semiconductor Components Industries, LLC.
PUBLICATION ORDERING INFORMATION
N. American Technical Support: 8002829855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81357733850
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 3036752175 or 8003443860 Toll Free USA/Canada
Fax: 3036752176 or 8003443867 Toll Free USA/Canada
Email: orderlit@onsemi.com
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative