ACPL-267XL, ACPL-268KL, ACPL-560XL, ACPL-563XL, 5962-08242* Hermetically Sealed, 3.3V High Speed, High CMR, Logic Gate Optocouplers Data Sheet *See Selection Guide for full matrix of part numbers. Description Features These units are single and dual channel, hermetically sealed optocouplers. The products are capable of operation and storage over the full military temperature range and can be purchased as either standard commercial product or with full MIL-PRF-38534 Class Level H or K testing or from DSCC Drawing 5962-08242. All devices are manufactured and tested on a MIL-PRF-38534 certified line and are included in the DSCC Qualified Manufacturers List QML-38534 for Hybrid Microcircuits. * Low power consumption Truth Table (Positive Logic) * 3.3V supply voltages * Dual marked with device part number and DSCC drawing number * Manufactured and tested on a MIL-PRF-38534 Certified Line * QML-38534, Class H and K * Three hermetically sealed package configurations * Performance guaranteed over full military temperature range: -55C to +125C Multichannel Devices Input Output * High speed: 10 Mbd typical On (H) L * CMR: > 10,000 V/s typical Off (L) H * 1500 Vdc withstand test voltage * TTL circuit compatibility Single Channel DIP * HCPL-260L/060L/263L/063L function compatibility Input Enable Output On (H) H L Applications Off (L) H H * Military and aerospace On (H) L H Off (L) L H * High reliability systems * Transportation, medical, and life critical systems * Line receiver Functional Diagram Multiple channel devices available VCC VE VOUT * Voltage level shifting * Isolated input line receiver * Isolated output line driver * Logic ground isolation * Harsh industrial environments * Isolation for computer, communication, and test equipment systems GND The connection of a 0.1 F bypass capacitor between VCC and GND is recommended. CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. Each channel contains a GaAsP light emitting diode which is optically coupled to an integrated high speed photon detector. The output of the detector is an open collector Schottky clamped transistor. Internal shields provide a guaranteed common mode transient immunity specification of 1000 V/s. Package styles for these parts are 8 and 16 pin DIP through hole (case outlines P and E respectively). Devices may be purchased with a variety of lead bend and plating options. See Selection Guide Table for details. Standard Microcircuit Drawing (SMD) parts are available for each package and lead style. Because the same electrical die (emitters and detectors) are used for each channel of each device listed in this data sheet, absolute maximum ratings, recommended operating conditions, electrical specifications, and performance characteristics shown in the figures are identical for all parts. Occasional exceptions exist due to package variations and limitations, and are as noted. Additionally, the same package assembly processes and materials are used in all devices. Selection Guide - Package Styles and Lead Configuration Options Package 16 Pin DIP 8 Pin DIP 8 Pin DIP Lead Style Through Hole Through Hole Through Hole Channels 2 1 2 Common Channel Wiring VCC, GND None VCC, GND Withstand Test Voltage 1500 Vdc 1500 Vdc 1500 Vdc Standard Commercial ACPL-2670L ACPL-5600L ACPL-5630L MIL-PRF-38534, Class H ACPL-2672L ACPL-5601L ACPL-5631L MIL-PRF-38534, Class K ACPL-268KL ACPL-560KL ACPL-563KL Standard Lead Finish Gold Plate Gold Plate Gold Plate Solder Dipped* Option -200 Option -200 Option -200 Butt Cut/Gold Plate Option -100 Option -100 Option -100 Gull Wing/Soldered* Option -300 Option -300 Option -300 Prescript for all below 5962- 5962- 5962- Either Gold or Solder 0824203HEX 0824201HPX 0824202HPX Gold Plate 0824203HEC 0824201HPC 0824202HPC Solder Dipped* 0824203HEA 0824201HPA 0824202HPA Butt Cut/Gold Plate 0824203HUC 0824201HYC 0824202HYC Butt Cut/Soldered* 0824203HUA 0824201HYA 0824202HYA Gull Wing/Soldered* 0824203HTA 0824201HXA 0824202HXA Prescript for all below 5962- 5962- 5962- Either Gold or Solder 0824203KEX 0824201KPX 0824202KPX Gold Plate 0824203KEC 0824201KPC 0824202KPC Solder Dipped* 0824203KEA 0824201KPA 0824202KPA Butt Cut/Gold Plate 0824203KUC 0824201KYC 0824202KYC Butt Cut/Soldered* 0824203KUA 0824201KYA 0824202KYA Gull Wing/Soldered* 0824203KTA 0824201KXA 0824202KXA Avago Part # & Options Class H SMD Part # Class K SMD Part # * Solder contains lead. Functional Diagrams 16 Pin DIP 8 Pin DIP 8 Pin DIP Through Hole Through Hole Through Hole 2 Channels 1 Channel 2 Channels 16 1 2 V CC 15 3 V O1 14 V CC 1 VE 2 13 4 V O2 5 6 12 11 GND 7 8 1 7 2 V OUT 3 VCC VO1 VO2 3 6 4 4 GND 10 GND 5 8 7 6 5 9 8 Note: Dual channel devices have common VCC and ground. Single channel DIP has an enable pin 7. All diagrams are "top view." Outline Drawings 16 Pin DIP Through Hole, 2 Channels 0.89 (0.035) 1.65 (0.065) 20.06 (0.790) 20.83 (0.820) 8.13 (0.320) MAX. 4.45 (0.175) MAX. 0.51 (0.020) MIN. 3.81 (0.150) MIN. 2.29 (0.090) 2.79 (0.110) 0.20 (0.008) 0.33 (0.013) 7.36 (0.290) 7.87 (0.310) 0.51 (0.020) MAX. NOTE: DIMENSIONS IN MILLIMETERS (INCHES). 8 Pin DIP Through Hole, 1 and 2 Channels Device Marking 6N134 Outline: 16-Pin DIP Pkg 8.13 (0.320) Avago LOGO MAX. 9.40 (0.370) 9.91 (0.390) 0.76 (0.030) 1.27 (0.050) 7.16 (0.282) 7.57 (0.298) 4.32 (0.170) MAX. Avago P/N DSCC SMD [1] DSCC SMD [1] PIN ONE/ ESD IDENT A QYYWWZ XXXXXX XXXXXXX XXX XXX * 50434 Note 1. Qualified parts only 3.81 (0.150) MIN. 0.51 (0.020) MIN. 2.29 (0.090) 2.79 (0.110) 0.51 (0.020) MAX. 0.20 (0.008) 0.33 (0.013) 7.36 (0.290) 7.87 (0.310) NOTE: DIMENSIONS IN MILLIMETERS (INCHES). COMPLIANCE INDICATOR, [1] DATE CODE, SUFFIX (IF NEEDED) COUNTRY OF MFR. Avago CAGE CODE [1] Hermetic Optocoupler Options Option Description 100 Surface mountable hermetic optocoupler with leads trimmed for butt joint assembly. This option is available on standard commercial, class H & class K product in 8 and 16 pin DIP (see drawings below for details). 4.32 (0.170) MAX. 0.51 (0.020) MIN. 1.14 (0.045) 1.40 (0.055) 0.51 (0.020) MAX. 2.29 (0.090) 2.79 (0.110) 4.32 (0.170) MAX. 0.51 (0.020) MIN. 2.29 (0.090) 2.79 (0.110) 1.14 (0.045) 1.40 (0.055) 0.20 (0.008) 0.33 (0.013) 0.51 (0.020) MAX. 7.36 (0.290) 7.87 (0.310) NOTE: DIMENSIONS IN MILLIMETERS (INCHES). 200 Lead finish is solder dipped rather than gold plated. This option is available on standard commercial, class H and class K products in 8 and 16 pin DIP. DSCC Drawing part numbers contain provisions for lead finish. 300 Surface mountable hermetic optocoupler with leads cut and bent for gull wing assembly. This option is available on standard commercial, class H & class K product in 8 and 16 pin DIP (see drawings below for details). This option has solder dipped leads. 4.57 (0.180) MAX. 0.51 (0.020) MIN. 1.40 (0.055) 1.65 (0.065) 0.51 (0.020) MAX. 2.29 (0.090) 2.79 (0.110) 4.57 (0.180) MAX. 0.51 (0.020) MIN. 2.29 (0.090) 2.79 (0.110) 1.40 (0.055) 1.65 (0.065) 5 MAX. 0.51 (0.020) MAX. NOTE: DIMENSIONS IN MILLIMETERS (INCHES). Solder contains lead. 4.57 (0.180) MAX. 0.20 (0.008) 0.33 (0.013) 9.65 (0.380) 9.91 (0.390) Absolute Maximum Ratings No derating required up to +125C. Parameter Symbol Min. Max. Units Storage Temperature TS -65 +150 C Operating Temperature TA -55 +125 C Case Temperature TC +170 C Junction Temperature TJ +175 C 260 for 10 sec C Lead Solder Temperature Peak Forward Input Current (each channel, 1 ms duration) IF(PEAK) 40 mA Average Input Forward Current (each channel) IF(AVG) 20 mA Input Power Dissipation (each channel) 35 mW Reverse Input Voltage (each channel VR 5 V Supply Voltage (1 minute maximum) VCC 7.0 V Output Current (each channel) IO 25 mA Output Voltage (each channel) VO 7 V Output Power Dissipation (each channel) PO 40 mW Package Power Dissipation (each channel) PD 200 mW VE 3.6 V Single Channel Product Only Enable Input Voltage 8 Pin Ceramic DIP Single Channel Schematic Note enable pin 7. An external 0.01 F to 0.1 F bypass capacitor must be connected between VCC and ground for each package type. ESD Classification MIL-PRF-38534 and MIL-STD-883, Method 3015 ACPL-560L/01L/0KL, 5962-0824201 ( B), Class 1B ACPL-5630L/31L/3KL, 5962-0824202 ( ACPL-2670L/72L/268KL, 5962-0824203 ( A), Class 3A ), Class 2 Recommended Operating Conditions Parameter Symbol Min. Max. Units Input Current, Low Level, Each Channel IFL 0 250 A Input Current, High Level, Each Channel IFH 10 20 mA Supply Voltage, Output VCC 3.0 3.6 V Fan Out (TTL Load) Each Channel N 6 Recommended Operating Conditions (cont'd.) Single Channel Product Only[10] Parameter Symbol Min. Max. Units High Level Enable Voltage VEH 2.0 VCC V Low Level Enable Voltage VEL 0 0.8 V Electrical Characteristics (TA = -55C to +125C, unless otherwise specified) Parameter Symbol Test Conditions High Level Output Current IOH VCC = 3.3 V, VO = 3.3 V, IF = 250 A Low Level Output Voltage VOL Current Transfer Ratio Logic High Supply Current Single Channel Logic low Supply Current Single Channel Group A[13] Subgroups Typ.* Max. Units Fig. Note 1, 2, 3 6 250 A 1 1 VCC = 3.3 V, IF = 10 mA, IOL (Sinking) = 10 mA 1, 2, 3 0.3 0.6 V 2 1, 8 hF CTR VO = 0.6 V, IF = 10 mA, VCC = 3.3 V 1, 2, 3 ICCH VCC = 3.3 V, IF = 0 mA 1, 2, 3 Dual Channel Min. 100 VCC = 3.3 V, IF1 = IF2 = 0 mA ICCL Dual Channel VCC = 3.3 V, IF = 20 mA 1, 2, 3 VCC = 3.3 V, IF1 = IF2 = 20 mA Input Forward Voltage VF Input Reverse Breakdown Voltage BVR IR = 10 A Input-Output Leakage Current II-O RH 65%, TA = 25C t = 5 s, VI-O = 1500 Vdc 1 Capacitance Between Input/ Output CI-O f = 1 MHz, TC = 25C 4 IF = 20 mA 1, 2 1, 2, 3 % 1 1 5 11 mA 10 22 mA 6 15 mA 12 30 mA 1.55 1.75 V 3 *All typical values are at VCC = 3.3 V, TA = 25C. Limits 1 3 1 1.85 5 1.0 V 1 1.0 A 2, 7 4.0 pF 1, 3, 13 Electrical Characteristics (cont'd) TA = -55C to +125C unless otherwise specified Group A[13] Subgroups Parameter Symbol Test Conditions Propagation Delay Time to High Output Level tPLH VCC = 3.3 V, RL = 510 , CL = 50 pF, IF = 13 mA Propagation Delay Time to Low Output Level tPHL Output Rise Time tLH Output Fall Time tHL Common Mode Transient Immunity at High Output Level Common Mode Transient Immunity at Low Output Level Limits Min. 9 Typ.* Max. Units Fig. Note 43 100 ns 4, 5, 6 1, 5 10, 11 140 9 54 10, 11 100 ns 120 RL = 510 , CL = 50 pF, IF = 13 mA 9, 10, 11 20 90 8 40 ns 1 |CMH| VCM = 50 V (PEAK), VCC = 3.3 V, VO (min.) = 2 V, RL = 510 , IF = 0 mA 9, 10, 11 1000 >10000 V/s 7 1, 6, 13 |CML| VCM = 50 V (PEAK), VCC = 3.3 V, VO (max.) = 0.8 V, RL = 510 , IF = 10 mA 9, 10, 11 1000 >10000 V/s 7 1, 6, 13 1, 2, 3 -2.0 -0.54 mA 2.0 Single Channel Product Only Low Level Enable Current IEL VCC = 3.3 V, VE = 0.5 V High Level Enable Voltage VEH 1, 2, 3 Low Level Enable Voltage VEL 1, 2, 3 V 0.8 9 V *All typical values are at VCC = 3.3 V, TA = 25C. Typical Characteristics, TA = 25C, VCC = 3.3 V Parameter Sym. Typ. Units Test Conditions Fig. Note Input Capacitance CIN 60 pF VF = 0 V, f = 1 MHz 1 Input Diode Temperature Coefficient VF TA -1.5 mV/C IF = 20 mA 1 Resistance (Input-Output) RI-O 1012 VI-O = 500 V 2 Propagation Delay Time of Enable from VEH to VEL tELH 32 ns Propagation Delay Time of Enable from VEL to VEH tEHL 28 ns RL = 510 , CL = 50 pF IF = 13 mA, VEH = 3 V, VEL = 0V Input-Input Leakage Current II-I 0.5 nA Relative Humidity 65% VI-I = 500 V, t = 5 s 4 Resistance (Input-Input) RI-I 1012 VI-I = 500 V 4 Capacitance (Input-Input) CI-I 0.55 pF f = 1 MHz 4 Single Channel Product Only 8, 9 1, 10 1, 11 Dual Channel Product Only Notes: 1. Each channel. 2. All devices are considered two-terminal devices; II-O is measured between all input leads or terminals shorted together and all output leads or terminals shorted together. 3. Measured between each input pair shorted together and all output connections for that channel shorted together. 4. Measured between adjacent input pairs shorted together for each multichannel device. 5. tPHL propagation delay is measured from the 50% point on the leading edge of the input pulse to the 1.5 V point on the leading edge of the output pulse. The tPLH propagation delay is measured from the 50% point on the trailing edge of the input pulse to the 1.5 V point on the trailing edge of the output pulse. 6. CML is the maximum rate of rise of the common mode voltage that can be sustained with the output voltage in the logic low state (VO < 0.8 V). CMH is the maximum rate of fall of the common mode voltage that can be sustained with the output voltage in the logic high state (VO > 2.0 V). 7. This is a momentary withstand test, not an operating condition. 8. It is essential that a bypass capacitor (0.01 to 0.1 F, ceramic) be connected from VCC to ground. Total lead length between both ends of this external capacitor and the isolator connections should not exceed 20 mm. 9. No external pull up is required for a high logic state on the enable input. 10. The tELH enable propagation delay is measured from the 1.5 V point on the trailing edge of the enable input pulse to the 1.5 V point on the trailing edge of the output pulse. 11. The tEHL enable propagation delay is measured from the 1.5 V point on the leading edge of the enable input pulse to the 1.5 V point on the leading edge of the output pulse. 12. Standard commercial parts receive 100% testing at 25C (Subgroups 1 and 9). Class H and K parts receive 100% testing at 25, 125, and 55C (Subgroups 1 and 9, 2 and 10, 3 and 11, respectively). 13. Parameters are tested as part of device initial characterization and after design and process changes. Parameters are guaranteed to limits specified for all lots not specifically tested. 80 60 40 20 0 -60 -40 -20 0 20 40 60 80 100 120 140 TA - TEMPERATURE - C Figure 1. High Level Output Current vs. Temperature. 5 VCC = 3.3 V VO = 3.3 V IF = 250 A VCC = 3.3 V TA = 25 C 4 VO - OUTPUT VOLTAGE -V IOH - HIGH LEVEL OUTPUT CURRENT - uA 100 3 RL 510 2 1 k 4 k 1 0 1 2 3 4 5 6 7 IF - INPUT DIODE FORWARD CURRENT - mA Figure 2. Input-Output Characteristics. Figure 3. Input Diode Forward Characteristics. D.U.T. VCC INPUT MONITORING NODE IF VO 120 VO 100 RL 0.01 F BYPASS C L* PROPAGATION DELAY - ns PULSE GENERATOR ZO = 50 tH = 5 ns 3.3 V GND Rm * CLINCLUDES PROBE AND STRAY WIRING CAPACITANCE. VCC = 3.3 V R L = 510 TA = 25C 80 tPLH 60 40 tPHL 20 0 10 11 12 13 14 15 16 17 18 19 20 IF - PULSE INPUT CURRENT - mA Figure 5. Propagation Delay, tPHL and tPLH vs. Pulse Input Current, IFH. Figure 4. Test Circuit for tPHL and tPLH.* D.U.T. B II A 120 PROPAGATION DELAY - ns 100 VCC +3.3 V 510 OUTPUT VO MONITORING 0.01 F NODE BYPASS VCC = 3.3 V IF = 13 mA RL = 510 GND VFF 80 tPLH + PULSE GEN. 60 40 VCM tPHL 20 0 -60 -40 -20 0 20 40 60 80 100 120 140 TA - TEMPERATURE - C Figure 6. Propagation Delay vs. Temperature. Figure 7. Test Circuit for Common Mode Transient Immunity and Typical Waveforms. 80 OUTPUT VE MONITORING NODE +3.3 V D.U.T. VCC VE IF = 13 mA RL VOUT 0.01 F BYPASS OUTPUT VO MONITORING CL* NODE GND * CL INCLUDES PROBE AND STRAY WIRING CAPACITANCE. tE - ENABLE PROPAGATION DELAY - ns PULSE GENERATOR ZO = 50 tr = 5 ns VCC = 3.3 V 70 VEH = 3.0 V VEL = 0 V 60 IF = 13 mA 50 t ELH 40 30 t EHL 20 10 0 -60 -40 -20 0 20 40 60 80 100 120 140 TA - TEMPERATURE - C Figure 9. Enable Propagation Delay vs. Temperature. Figure 8. Test Circuit for tEHL and tELH. VCC +5.5 V VOC +5.5 V D.U.T.* (EACH INPUT) + VIN VCC 0.01 F 200 5.3 V (EACH OUTPUT) GND 200 (EACH OUTPUT) CONDITIONS: IF = 20 mA IO = 25 mA TA = +125 oC * ALL CHANNELS TESTED SIMULTANEOUSLY. Figure 10. Operating Circuit for Burn-In and Steady State Life Tests. 10 MIL-PRF-38534 Class H, Class K, and DSCC SMD Test Program Avago's Hi-Rel Optocouplers are in compliance with MIL-PRF-38534 Classes H and K. Class H and Class K devices are also in compliance with DSCC drawing 5962-08242. Testing consists of 100% screening and quality conformance inspection to MIL-PRF-38534. For product information and a complete list of distributors, please go to our website: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries. Data subject to change. Copyright (c) 2005-2008 Avago Technologies Limited. All rights reserved. AV02-1327EN - June 30, 2008