F-51477GNF-SLY-ALN - Optrex America Inc.

F-51477GNF-SLY-ALN (AL) No. 2005-0065 OPTREX CORPORATION Page 1/18

LCD Module Technical Specification

F-51477GNF-SLY-ALN

Table of Contents

1. General Specifications..................................................................................................................................2

2. Electrical Specifications...............................................................................................................................3

3. Optical Specifications ...................................................................................................................................7

4. I/O Terminal......................................................................................................................................................9

5. Test...................................................................................................................................................................11

6. Appearance Standards................................................................................................................................12

7. Code System of Production Lot...............................................................................................................16

8. Type Number..................................................................................................................................................16

9. Applying Precautions ..................................................................................................................................16

10. Precautions Relating Product Handling................................................................................................17

11. Warranty........................................................................................................................................................18

Revision History

Rev. Date Page Comment

Type No.

Feb 17, 2005

First Edition

Final Revision

******

Checked by (ACI Engineering Division)

)

Approved by (Quality Assurance Division)

)

Prepared by (ACI Engineering Division)

F-51477GNF-SLY-ALN (AL) No. 2005-0065 OPTREX CORPORATION Page 2/18

1. General Specifications

Operating Temp. :min. 0°C ~max. 50°C

Storage Temp. :min. -20°C ~max. 60°C

Dot Pixels :320 (W) × 240 (H) dots

Dot Size :0.285 (W) × 0.285 (H) mm

Dot Pitch :0.3 (W) × 0.3 (H) mm

Viewing Area :99.85 (W) × 77.0 (H) mm

Outline Dimensions :116.4* (W) × 94.0 (H) × 6.0 max. (D) mm

* Without FPC

Weight :102g max.

LCD Type :NSD-21295

( F-STN / Black &White-mode / Transflective )

Viewing Angle :6:00

Data Transfer :4-bit parallel data transfer

Backlight :LED Backlight / Yellow-green

Drawings :Dimensional Outline UE-310885C

RoHS regulation :To our best knowledge, this product satisfies material

requirement of RoHS regulation.

Our company is doing the best efforts to obtain

the equivalent certificate from our suppliers.

F-51477GNF-SLY-ALN (AL) No. 2005-0065 OPTREX CORPORATION Page 3/18

2. Electrical Specifications

2.1. Absolute Maximum Ratings VSS=0V

Parameter Symbol Conditions Min. Max. Units

Supply Voltage

(Logic)

VDD-VSS --0.3 7.0 V

Supply Voltage

(LCD Drive)

V0-V5--0.3 30.0 V

Input Voltage VI--0.3 VDD+0.3 V

2.2. DC Characteristics Ta=25°C, VSS=0V

Parameter Symbol Conditions Min. Typ. Max. Units

Supply Voltage

(Logic)

VDD-VSS -4.5 -5.5 V

Supply Voltage

(LCD Drive)

V0-V5Shown in 3.1 V

High Level

Input Voltage

VIH VDD=4.5~5.5V 0.8×VDD - - V

High Level

output Voltage

VOHIOH=-0.4mA VDD-0.4 - - V

Low Level

Input Voltage

VIL VDD=4.5~5.5V 0-0.2×VDD V

Low Level

output Voltage

VOLIOH=0.4mA - - 0.4V

Supply Current

IDD VDD-VSS=5.0V -0.10 0.15 mA

I0V0-V5=22.4V-0.80 1.20 mA

F-51477GNF-SLY-ALN (AL) No. 2005-0065 OPTREX CORPORATION Page 4/18

2.3. AC Characteristics VDD=4.5~5.5V

Parameter Symbol Min. Max. Units

Shift Clock Period tWCK 71 -ns

Shift Clock “H” Pulse Width tWCKH 23 -ns

Shift Clock “L” Pulse Width tWCKL 23 -ns

Data Setup Time tDS 10 -ns

Data Hold Time tDH 20 -ns

Latch Pulse “H” Pulse Width tWLPH 15 -ns

Shift Clock Rise to Latch Pulse Rise Time tLD 0-ns

Shift Clock Fall to Latch Pulse Fall Time tSL 25 -ns

Latch Pulse Rise to Shift Clock Rise Time tLS 25 -ns

Latch Pulse Fall to Shift Clock Rise Time tLH 25 -ns

Input Signal Rise,Fall Time tr, tf-50 Note.1 ns

DISPOFF Removal Time tSD100 -ns

DISPOFF Enable Pulse Width tWDL 1.2 -µs

Output Delay Time tDL -200 Note.2 ns

Note.1 : (tCK – twckll - twckl)/2 is the maximum in case of high speed operation.

Note.2 : CL=15pF

WDL

WCKL

tSL

tLD

DISPOFF

WLPH

TOP DATALAST DATA

WCK

WCKH

TDL

FLM

(NT7704)

F-51477GNF-SLY-ALN (AL) No. 2005-0065 OPTREX CORPORATION Page 5/18

2.4. Timing Chart

2.5. Comparison of Display and Data

T=0.0595ms typ.

240xT

(Reduction)

#1 DATA

SEGSEG SEGSEG SEGSEG SEGSEG

320316 4 320316 84

317~

313~

317~

313~

FLM

SEG1 SEG320

#240

D2D3

D0~D3

TOP VIEW

D0D1 D0D1

F-51477GNF-SLY-ALN (AL) No. 2005-0065 OPTREX CORPORATION Page 6/18

2.6. Lighting Specifications

2.6.1. Absolute Maximum Ratings Ta=25°C

Parameter Symbol Conditions Min. Typ. Max. Units

Foward Current IFNote 1 - - 360 mA

Reverse Voltage VR- - - 8.0 V

LED Power Dissipation PD- - - 1.872 W

Note 1 : Refer to the foward current derating curve.

2.6.2. Operating Characteristic Ta=25°C

Parameter Symbol Conditions Min. Typ. Max. Units

Foward Voltage VFIF=180mA -4.4 5.2 V

Luminance of

Backlight Surface

LIF=180mA 150 - - cd/m2

50250 Ta (

180

360

IF (mA)

F-51477GNF-SLY-ALN (AL) No. 2005-0065 OPTREX CORPORATION Page 7/18

3. Optical Specifications

3.1. LCD Driving Voltage

Parameter Symbol Conditions Min. Typ. Max. Units

Recommended Ta= 0°C- - 25.4 V

LCD Driving Voltage V0-V5Ta=25°C20.8 22.4 23.9 V

Note 1 Ta=50°C19.4 - - V

Note 1 : Voltage (Applied actual waveform to LCD Module) for the best contrast. The range of

minimum and maximum shows tolerance of the operating voltage. The specified contrast

ratio and response time are not guaranteed over the entire range.

3.2. Optical Characteristics Ta=25°C, 1/240 Duty, 1/14 Bias, VOD=22.4V (Note 4), θ= 0°, φ=-°

Parameter Symbol Conditions Min. Typ. Max. Units

Contrast Ratio Note 1 CR θ= 0°,φ =-°-3.5 -

Viewing Angle Shown in 3.3

Response Rise Note 2 TON - - 360 540 ms

Time Decay Note 3 TOFF - - 280 420 ms

Note 1 :Contrast ratio is definded as follows.(CR = LOFF / LON)

LON :Luminance of the ON segments

LOFF :Luminance of the OFF segments

Measuring Spot : 3.0mmφ

Note 2 :The time that the luminance level reaches 90% of the saturation level from 0%

when ON signal is applied.

Note 3 :The time that the luminance level reaches 10% of the saturation level from 100%

when OFF signal is applied.

Note 4 :Definition of Driving Voltage VOD

VOD=V0-V5

Assuming that the typical driving waveforms shown below are applied to the LCD

Panel at 1/A Duty - 1/B Bias (A: Duty Number, B: Bias Number). Driving voltage

VOD is definded as follows.

VOD = (Vth1+Vth2) / 2

Vth1: The voltage VO-P that should provide 70% of the saturation level in the

luminance at the segment which the ON signal is applied to.

Vth2: The voltage VO-P that should provide 20% of the saturation level in the

luminance at the segment which the OFF signal is applied to.

Vo-p

1 /fF

( B-2 ) ×Vo-p/B

1/( fF×A )

( OFF SIGNAL )

( ON SIGNAL )

F-51477GNF-SLY-ALN (AL) No. 2005-0065 OPTREX CORPORATION Page 8/18

3.3. Definition of Viewing Angle and Optimum Viewing Area

*Point • shows the point where contrast ratio is measured. : θ= 0°, φ= -°

*Driving condition: 1/240 Duty, 1/14 Bias, VOD=22.4V, fF=70Hz

270°

180°

270°

135°

315°225°

45°

180°

90°

(φ = 0°)

*Area shows typ. CR≥1.5 (Measuring Spot : 3.0mmφ)

3.4. System Block Diagram

Halogen bulb

Computer

Rotation Table ( θ,φ )

Temperature Chamber

LCD

Optical Fiber

Waveform Generator

Control Unit &

#1980A WB

Photometer φ

F-51477GNF-SLY-ALN (AL) No. 2005-0065 OPTREX CORPORATION Page 9/18

4. I/O Terminal

4.1. Pin Assignment

CN1

No. Symbol Function

1NC Non-connection

2V0Power Supply for LCD Drive

3V1Power Supply for LCD Drive V1 = 13/14,V5

4V2Power Supply for LCD Drive V2 = 12/14,V5

5V3Power Supply for LCD Drive V3 = 2/14,V5

6V4Power Supply for LCD Drive V4 = 1/14,V5

7V5Power Supply for LCD Drive V5,VOUT

8VSS Power Supply ( 0V, GND )

9MAlternate Signal for LCD Drive

10 FLM First Line Marker

11 LP Data Latch Signal

12 DISPOFF Display Control Signal H : Display on L : Display off

13 CP Clock Signal for Shifting Data

14 D0 Data Bus Line

15 D1 Data Bus Line

16 D2 Data Bus Line

17 D3 Data Bus Line

18 VDD Power Supply for Logic

19 VSS Power Supply ( 0V, GND )

20 NC Non-connection

21 NC Non-connection

22 LED ANODE LED Anode Terminal

23 LED CATHODE LED Cathode Terminal

F-51477GNF-SLY-ALN (AL) No. 2005-0065 OPTREX CORPORATION Page 10/18

4.2. Example of Power Supply

It is recommended to apply a potentiometer for the contrast adjust due to the

tolerance of the driving voltage and its temperature dependence.

4.3. Block Diagram

or equivalent

LED CATHODE

LED A

NODE

FLM

D0〜D3

DISPOFF

V0∼5

NT7704 × 1

Common Driver

NT7703 × 2

Segment Driver

L C D P

320

240

320 × 240 dots

LED Backlight

VDD

VSS

To LSI for Logic

or equivalent

(

Logic

)

VHH (+Voltage)

R1+R2+VR=10~20KΩ

R=1KΩ∼10KΩ

VDD

VSS

Module

F-51477GNF-SLY-ALN (AL) No. 2005-0065 OPTREX CORPORATION Page 11/18

5. Test

No change on display and in operation under the following test condition.

Conditions: Unless otherwise specified, tests will be conducted under the following condition.

Temperature: 20±5°C

Humidity : 65±5%RH

tests will be not conducted under functioning state.

No. Parameter Conditions Notes

1High Temperature Operating 50°C±2°C, 96hrs (operation state)

2Low Temperature Operating 0°C±2°C, 96hrs (operation state) 1

3High Temperature Storage 60°C±2°C, 96hrs 2

4Low Temperature Storage -20°C±2°C, 96hrs 1,2

5Damp Proof Test 40°C±2°C,90~95%RH, 96hrs 1,2

6Vibration Test Total fixed amplitude : 1.5mm 3

Vibration Frequency : 10~55Hz

One cycle 60 seconds to 3 directions of X, Y, Z for

each 15 minutes

7Shock Test To be measured after dropping from 60cm high on

the concrete surface in packing state.

Note 1 :No dew condensation to be observed.

Note 2 :The function test shall be conducted after 4 hours storage at the normal

Temperature and humidity after removed from the test chamber.

Note 3 :Vibration test will be conducted to the product itself without putting it in a container.

60cm

Concrete Surface

Dropping method corner dropping

E,F,G face : once

B,C,D edge : once

A corner : once

Face dropping

Edge dropping

F-51477GNF-SLY-ALN (AL) No. 2005-0065 OPTREX CORPORATION Page 12/18

6. Appearance Standards

6.1. Inspection conditions

The LCD shall be inspected under 40W white fluorescent light.

The distance between the eyes and the sample shall be more than 30cm.

All directions for inspecting the sample should be within 45°against perpendicular line.

6.2. Definition of applicable Zones

A Zone : Active display area

B Zone : Out of active display area ~ Maximum seal line

C Zone : Rest parts

A Zone + B Zone = Validity viewing area

X : Maximum Seal Line

A Zone

B Zone

C Zone

F-51477GNF-SLY-ALN (AL) No. 2005-0065 OPTREX CORPORATION Page 13/18

6.3. Standards(middle scale, LED) D = ( Long + Short ) / 2 * : Disregard Units : mm

No. Parameter Criteria

1The Shape of Dot (1) Pin Hole

Dimension Acceptable Number

D ≤ 0.10 *

1 pc / dot(only segment)or less

0.10 < D ≤ 0.20 5 pcs / cell or less

(2) Pattern Shift

| A – B | ≤ 0.15

(3) Breakage or Chips / Deformation

1.Segment Type

Dimension Acceptable Number

A ≤ 0.10 *

B ≤ 0.15 *

2.Dot Type

Dimension Acceptable Number

A≤0.10*

(Should not be connected to next dot)

1 pc / dot(only segment)or less

5 pcs / cell or less0.10<A≤0.15

(Should not be connected to next dot)

B ≤ 0.15 *

3.Defective type extends over multiple numbers of dots

Dimension Acceptable Number

D≤0.10*

1 pc / dot(only segment)or less

5 pcs / cell or less

(Individual dot must secure 1/2 area

0.10<D≤0.20

or more)

F-51477GNF-SLY-ALN (AL) No. 2005-0065 OPTREX CORPORATION Page 14/18

D = ( Long + Short ) / 2 * : Disregard Units : mm

No. Parameter Criteria

2Black and (1) Round Shape

White Spots, Zone Acceptable Number

Foreign Substances Dimension A B C

D ≤ 0.10 * * *

0.10< D ≤ 0.20 6 6 *

0.20< D ≤ 0.30 4 4 *

Individual dot must secure 1/2 area or more.

(2) Line Shape

Zone Acceptable Number

Length Width A B C

* W≤0.03 * * *

L ≤2.0 0.03<W≤0.05 5 5 *

L ≤1.0 ≤0.10 4 4 *

* 0.10<W In the same way (1) *

No more than 9pcs as total.

(Refer to “Complex Foreign Substance Defects”)

3Color Variation Not to be conspicuous defects.

4Air Bubbles

(between glass Zone Acceptable Number

& polarizer) Dimension A B C

D ≤ 0.30 * * *

0.30< D ≤ 0.40 3* *

0.40< D ≤ 0.60 2 3 *

No more than 3pcs as total.

(Refer to “Complex Foreign Substance Defects”)

5Polarizer Scratches Not to be conspicuous defects.

6Polarizer Dirts If the stains are removed easily from LCDP surface, the module is

not defective.

7Complex Foreign Black spots, line shaped foreign substances or air bubbles between

Substance Defects glass & polarizer should be 9pcs maximum in total.

8Distance between 20mm or more

Different Foreign

Substance Defects

F-51477GNF-SLY-ALN (AL) No. 2005-0065 OPTREX CORPORATION Page 15/18

D = ( Long + Short ) / 2 * : Disregard Units : mm

No. Parameter Criteria

11 Chipped Glass (1) Other than electrode pad areas and corner areas

X Y Z

≤10.0 ≤1.5 ≤t

(2) Corner Areas

1.Lead Areas

X Y Z

Half dimension till first

Leads terminal Same as terminal width *

It is allowed 1 chip as total length of Z sirection

In case of 2 or more chips, Z ≤ 1/2t

2.Other than electrode pad Areas

X+Y≤8.0

If the chipped area touches the seal line, the LCD is not acceptable.

X Y

F-51477GNF-SLY-ALN (AL) No. 2005-0065 OPTREX CORPORATION Page 16/18

7. Code System of Production Lot

The production lot of module is specified as follows.

Factory Control Number (0~99)

Date of the week (A~G)

Factory Number (0~9)

Factory Code (Alphabet)

Production Week (1~5)

Production Month (1~9, X, Y, Z)

Production Year (Lower 2 digits)

8. Type Number

The type number of module is specified as follows.

F-51477GNF-SLY-ALN

9. Applying Precautions

Please contact us when questions and/or new problems not specified in this

Specifications arise.

F-51477GNF-SLY-ALN (AL) No. 2005-0065 OPTREX CORPORATION Page 17/18

10. Precautions Relating Product Handling

The Following precautions will guide you in handling our product correctly.

1) Liquid crystal display devices

1. The liquid crystal display device panel used in the liquid crystal display module is

made of plate glass. Avoid any strong mechanical shock. Should the glass break

handle it with care.

2. The polarizer adhering to the surface of the LCD is made of a soft material.

Guard against scratching it.

2) Care of the liquid crystal display module against static electricity discharge.

1. When working with the module, be sure to ground your body and any electrical

equipment you may be using. We strongly recommend the use of anti static mats

( made of rubber ), to protect work tables against the hazards of electrical shock.

2. Avoid the use of work clothing made of synthetic fibers. We recommend cotton

clothing or other conductivity-treated fibers.

3. Slowly and carefully remove the protective film from the LCD module, since this

operation can generate static electricity.

3) When the LCD module alone must be stored for long periods of time:

1. Protect the modules from high temperature and humidity.

2. Keep the modules out of direct sunlight or direct exposure to ultraviolet rays.

3. Protect the modules from excessive external forces.

4) Use the module with a power supply that is equipped with an overcurrent protector

circuit,since the module is not provided with this protective feature.

5) Do not ingest the LCD fluid itself should it leak out of a damaged LCD module. Should

hands or clothing come in contact with LCD fluid, wash immediately with soap.

6) Conductivity is not guaranteed for models that use metal holders where solder

connections between the metal holder and the PCB are not used. Please contact us

to discuss appropriate ways to assure conductivity.

7) For models which use CFL:

1. High voltage of 1000V or greater is applied to the CFL cable connector area.

Care should be taken not to touch connection areas to avoid burns.

2. Protect CFL cables from rubbing against the unit and thus causing the wire jacket to

become worn.

3. The use of CFLs for extended periods of time at low temperatures will significantly

shorten their service life.

8) For models which use touch panels:

1. Do not stack up modules since they can be damaged by components on neighboring

modules.

2. Do not place heavy objects on top of the product. This could cause glass breakage.

9) For models which use COG,TAB,or COF:

1. The mechanical strength of the product is low since the IC chip faces out unprotected

from the rear. Be sure to protect the rear of the IC chip from external forces.

2. Given the fact that the rear of the IC chip is left exposed, in order to protect the unit

from electrical damage, avoid installation configurations in which the rear of the IC

chip runs the risk of making any electrical contact.

F-51477GNF-SLY-ALN (AL) No. 2005-0065 OPTREX CORPORATION Page 18/18

10) Models which use flexible cable, heat seal, or TAB:

1. In order to maintain reliability, do not touch or hold by the connector area.

2. Avoid any bending, pulling, or other excessive force, which can result in broken

connections.

11) In case of buffer material such as cushion / gasket is assembled into LCD module,

it may have an adverse effect on connecting parts ( LCD panel-TCP / HEAT SEAL / FPC /

etc., PCB-TCP / HEAT SEAL / FPC etc., TCP-HEAT SEAL, TCP-FPC, HEAT SEAL-FPC,

etc.,) depending on its materials.

Please check and evaluate these materials carefully before use.

12) In case of acrylic plate is attached to front side of LCD panel, cloudiness ( very small

cracks ) can occur on acrylic plate, being influenced by some components generated

from polarizer film..

Please check and evaluate those acrylic materials carefully before use.

11. Warranty

This product has been manufactured to your company’s specifications as a part for use in

your company’s general electronic products. It is guaranteed to perform according to

delivery specifications. For any other use apart from general electronic equipment, we

cannot take responsibility if the product is used in medical devices, nuclear power control

equipment, aerospace equipment, fire and security systems, or any other applications in

which there is a direct risk to human life and where extremely high levels of reliability are

required. If the product is to be used in any of the above applications, we will need to enter

into a separate product liability agreement.

1. We cannot accept responsibility for any defect, which may arise from additional

manufacturing of the product (including disassembly and reassembly), after

product delivery.

2. We cannot accept responsibility for any defect, which may arise after the application

of strong external force to the product.

3. We cannot accept responsibility for any defect, which may arise due to the application

of static electricity after the product has passed your company’s acceptance inspection

procedures.

4. When the product is in CFL models, CFL service life and brightness will vary

According to the performance of the inverter used, leaks, etc. We cannot accept

responsibility for product performance, reliability, or defect, which may arise.

5. We cannot accept responsibility for intellectual property of a third party, which may

arise through the application of our product to your assembly with exception to those

issues relating directly to the structure or method of manufacturing of our product.

6. Optrex will not be held responsible for any quality guarantee issue for defect products

judged as Optrex-origin longer than 2 (two) years from Optrex production or 1(one)

year from Optrex, Optrex America, Optrex Europe delivery which ever comes later.