24V DRIVE INTERFACE BOARD (PARALLEL) FTP-622DCL001/011/ FTP-622DSL001/011/012 FOR FTP-622/632/642MCL001/002/301/302/303/304 INTERFACE 1. Centronics (1) Connector (CN1) Connector part number : FCN-605Q030-G/S (Fujitsu Components) Mating connector part number : FCN-607B030-G/D (Fujitsu Components) or equivalent (2) Connector pin assignment No. Signal I/O Contents No. Signal I/O Contents 1 PRSTB I Data strobe 2 PRSTB-RET -- Connected to logic GND 3 PRDT0 I Data 0 4 PRDT0-RET -- Connected to logic GND 5 PRDT1 I Data 1 6 PRDT1-RET -- Connected to logic GND 7 PRDT2 I Data 2 8 PRDT2-RET -- Connected to logic GND 9 PRDT3 I Data 3 10 PRDT3-RET -- Connected to logic GND 11 PRDT4 I Data 4 12 PRDT4-RET -- Connected to logic GND 13 PRDT5 I Data 5 14 PRDT5-RET -- Connected to logic GND 15 PRDT6 I Data 6 16 PRDT6-RET -- Connected to logic GND 17 PRDT7 I Data 7 18 PRDT7-RET -- Connected to logic GND 19 ACKNLG O Data input acknowledge 20 ACKNLG-RET -- Connected to logic GND 21 BUSY O Busy 22 BUSY-RET -- Connected to logic GND 23 RINF2 O Printer status 24 INPRM-RET -- Connected to logic GND 25 SLCTIN I Printer select 26 INPRM I Reset 27 RINF1 O Printer status 28 RINF3 O Printer status 29 ATF I Paper feed request 30 GND -- Logic GND Notes: * Symbol "----" means a negative logic signal. * "-RET" signal is a return signal of the twisted pair cable. * "I" or "O" means a signal direction from the interface board side. (4) Data input signal timing (3) Connector pin number PRDT0~7 t1 FCN-605Q030-G/S (Fujitsu Components) or equivalent No.1 t3 PRSTB t2 BUSY t4 ACKNLG No.30 t5 No.2 Data set time :t10.5 sec PRSTB pulse :t20.5 sec Data hold time :t30.5 sec 1 PRSTB to BUSY= "H" :t40.5 sec . ACKNLG pulse :t5=5.0 sec . FTP-622DCL/DSL Product Part Number Function FTP-622DCL001 Standard (without cutter) FTP-622DCL011 With cutter control FTP-622DSL001 Standard (without cutter) FTP-622DSL011 With cutter controller FTP-622DSL012 With cutter controller + FLASH ROM FTP-622DSL112 With Cutter + KANJI+FLASH ROM Parallel Interface Board Serial Interface Board SPECIFICATION Item Specification Data receive speed 19200, 9600, 4800, 1200 bps (set by dip switch) Synchronous method Asynchronous, full duplex Hand shake DTR/DSR signal or XON/XOFF Input output level RS232C Signal level Space (logic = 0) Mark (logic = 0) +3 V ~ +12 V -3 V ~ -12 V 2. SERIAL INTERFACE (RS232C) (1) Connector (CN2) Part number : B6B-XH-A (J.S.T) Mating connector part number : XHP-6 (J.S.T) or equivalent (2) Pin assignment No. Signal I/O Contents No. Signal I/O Contents 1 FG -- Frame GND 2 RD I Receive data 3 TD O Transmission Data 4 DTR O Data terminal ready 5 GND -- Signal GND 6 DSR I Data set ready Notes: "I" or "O" means a signal direction from the interface board side. (3) Pin number B6B-XH-A (J.S.T) CN2 CN1 6 1 2 FTP-622DCL/DSL CONNECTOR PIN ASSIGNMENT 1. Connector for power supply (CN10) Part number : B6P-VH (J.S.T) Mating connector part number : VHR-6N (J.S.T) or equivalent No. Signal I/O Contents No. Signal I/O Contents 1 VCC -- Power supply for logic (+5 V) 2 GND -- GND (5 V, 24 V common) 3 GND -- GND (5 V, 24 V common) 4 GND -- GND (5 V, 24 V common) 5 VDD -- Power for head/motor (+24 V) 6 V DD -- Power for head/motor (+24 V) 2. Connector for thermal head drive (CN8) Part number : B16B-PH-K-S (J.S.T) Mating connector part number : PHR-16 (J.S.T) or equivalent No. Signal I/O Contents No. Signal I/O Contents 1 VDH O Power for head (+24 V) 2 VDH O Power for head (+24 V) 3 GND (VDH) -- Head GND 4 GND (VDH) -- Head GND 5 STB1 O Print enable signal 1 6 STB2 O Print enable signal 2 7 STB3 O Print enable signal 3 8 TMP I Temperature detection signal 9 STB4 O Print enable signal 4 10 LAT O Print data latch signal 11 STB5 O Print enable signal 5 12 5 VH O Power for logic (+5 V) 13 HCLK O Data transmission clock 14 HD O Print data output signal 15 GND (VDH) -- Head GND 16 VDH O Power for head (+24 V) Notes: * Symbol "----" means a negative logic signal. * "I" or "O" means a signal direction from the interface board side. 3. Connector for Sensor (CN3) Part number No. Signal : B5B-PH-K-S (J.S.T) I/O Contents No. Signal I/O 1 +5 V -- Power for logic (+5 V) 2 PES I 3 GND (5 V) -- Logic GND 4 +5 V -- 5 HUP I Contents Paper end detect signal Power for logic (+5 V) Head-up detect signal 3 FTP-622DCL/DSL 7. Connector for control signal input/ output (CN1) Part number Mating connector No. Signal : FCN-605Q030-G/S (Fujitsu Components) : FCN-607B030-G/D (Fujitsu Components) or equivalent I/O Contents No. Signal I/O Contents 1 NC -- No connection 2 NC -- No connection 3 NC -- No connection 4 NC -- No connection 5 NC -- No connection 6 NC -- No connection 7 NC -- No connection 8 NC -- No connection 9 NC -- No connection 10 NC -- No connection 11 NC -- No connection 12 NC -- No connection 13 NC -- No connection 14 NC -- No connection 15 NC -- No connection 16 NC -- No connection 17 NC -- No connection 18 NC -- No connection 19 NC -- No connection 20 NC -- No connection 21 NC -- No connection 22 NC -- No connection 23 NC -- No connection 24 NC -- No connection 25 SLCTIN Select signal 26 INPRM 27 NC -- No connection 28 NC -- No connection 29 ATF I Paper feed request 30 GND -- GND I I Reset signal *Do not connect outside signal to NC. 4 FTP-622DCL/DSL 4. Connector for paper near end detection (CN5) Part number : B2B-PH-K-S (J.S.T) Mating connector part number : PHR-2 (J.S.T) or equivalent No. 1 Signal +5 V I/O -- Contents Power for logic (+5 V) No. 2 Signal NES I/O I Contents Paper near end detect signal 5. Connector for stepping motor drive (CN13) Part number No. Signal : B4B-PH-K-S (J.S.T) I/O Contents No. Signal I/O Contents 1 MT/B O Stepping motor coil excitation 2 MT/B O Stepping motor coil excitation 3 MT/A O Stepping motor coil excitation 4 MT/A O Stepping motor coil excitation 6. Connector for cutter drive (CN11) *1 Part number No. Signal : B4B-EH (J.S.T) I/O Contents No. Signal I/O Contents 1 SW1 I Cutter position detect signal 2 GND -- Logic ground 3 M+ O Motor control signal (+) 4 M- O Motor control signal (-) *1: Only for FTP-622DCL011/111. 5 FTP-622DCL/DSL PRINTING COMMANDS (CENTRONICS INTERFACE) Command Contents HT Moves the print position to the next tab. LF Line feed. FF Feeds forms (new page). ESC RS Sets reverse printing. ESC US Resets reverse printing. ESC ! +n Sets print mode. ESC* +m+n1+n2+d1~dN Sets the bit image mode "m" for n1, n2 dot numbers. ESC 2 Sets 1/6 inch line feed length. ESC 3 + n Sets the line feed length. ESC @ Printer initialization. ESC A+n Sets the space between lines. ESC C+n Sets the page length by character line. ESC D+d1~dN+NUL Sets the tab position. ESC J+n Feeds paper in forward direction. ESC K+n Feeds paper in reverse direction. ESC c+1+n Sets the internal processing. ESC R+n Selects the international character. ESC s+n Sets the printing speed. ESC d+n Printing and n-line feeding. ESC e+n Reverse line feed in "n" lines after printing. ESC t+n Character code table selection. ESC {+n Sets/resets the upside down printing. ECS EM+n Automatic paper feed distance setting. ESC X+n+m Setting turning time of the motor excitation. ESC V+n Right Rotation 90 specification / cancellation. ESC %+n Selects the font to download*3. ESC &+y+c1+c2+x+d1~dn Registers the download front*3. ESC ?+n External character registration deletion*3. FS E+n Correction of impressed energy. FS ! +n Sets the Kanji print mode*1. FS & Sets Kanji mode*1. (Continued) 6 FTP-622DCL/DSL (Continued) Command Contents FS . Resets Kanji mode*1. FS C+n Selects Kanji code type*1. FS 9+n Sets the detection functions. FS*+m+n1+n2+d1~dn Prints image data on SRAM*3. FS r+n Notifies of printing finish*4. FS W+n Sets/resets 4 times enlarged character. GS < Line feeds to the next mark. GS A+m+n Sets the line feed length after mark detection. GS E+n Sets print quality. GS V+n+m Executes paper cutting*2. GS e+n+m Sets the bar width. GS h+n Sets the barcode height. GS k+m+n+d1~dN Selects the barcode type and prints. GS w+n Sets the barcode length. GS &+m+x+y1+y2+[d]k Registration of image data*3. GS '+m+n Prints registered image data *3. GS a+n Sets and cancels status transmission (valid only for DSL)*3. *1: Only for FTP-622DSL112. *2: Only for FTP-622DCL011 or FTP-622DSL011/012. *3: Only for FTP-622DSL012. *4: Only for FTP-622DSL011/012. 7 FTP-622DCL/DSL OPTIONS 1. Cable (With FTP-622MCL, FTP-632MCL, FTP-642MCL) Name Part Number Cable Length FTP-622Y001 270 mm (10.6 inches) Centronics (CN1) FTP-622Y201 500 mm (19.71 inches) Serial (CN2) FTP-622Y301 500 mm (19.71 inches) Power cable for head, motor, and logic (CN10) FTP-622Y401 300 mm (11.8 inches) * short cable option FTP-624Y001 150 mm (5.9 inches) Thermal head connection cable (CN8)* Interface cable 2. Paper holder Name Part number Flange FTP-040HF Stand FTP-040HS Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: www.fceu.fujitsu.com North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: marcom@fcai.fujitsu.com Web: www.fcai.fujitsu.com Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #04-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com www.fcal.fujitsu.com (c) 2004 Fujitsu Components America, Inc. All company and product names are trademarks or registered trademarks of their respective owners. Rev. 11/15/2004. 8