Series CCS-37S/CS-37S COAX SWITCHES Miniature DC-18 GHz Failsafe TRANSFER Coaxial Switch PART NUMBER DESCRIPTION CCS-37S Commercial Failsafe TRANSFER, DC-18GHz CS-37S Elite Failsafe TRANSFER, DC-18GHz Available with USB & Ethernet Control! The CCS-37S/CS-37S is a long-life high performance transfer switch designed for use in 50 Ohms coaxial transmission lines operating over frequencies ranging from DC to 18 GHz. The switch is designed for minimum size compatible with SMA connector spacing. The failsafe switches on this page are provided with a spring operated actuator which is particularly desirable in applications where the switch is connected to one position (normally closed) most of the time and only periodically switched to the alternate position. In this type of application, holding power is required only when operating in the alternate position. Also, switching circuitry is simplified, since only one DC circuit is required. ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS ELECTRICAL CHARACTERISTICS Operating Temperature Commercial Model, CCS-37S Elite Model, CS-37S Form Factor -25C to 65C -55C to 85C TRANSFER, break before make Vibration (MIL-STD-202 Method 214, Condition D, non-operating) 10 g's RMS Frequency Range CCS-37S CS-37S DC-18 GHz DC-18 GHz Shock (MIL-STD-202 Method 213, Condition D, non-operating) 500 g's Characteristic Impedance 50 Ohms Standard Actuator Life Actuator Life w/ Additional Features 5,000,000 cycles 1,000,000 cycles Operate Time 10 ms (max.) Release Time 10 ms (max.) Connector Type SMA Humidity (Moisture Seal) Available Weight 2.5 oz. (70.87g) (max.) Actuation Voltage Available 12 Actuation Current, max. @ ambient 380 300 250 200 mA 15 24 28 V TYPICAL PERFORMANCE CHARACTERISTICS Frequency Insertion Loss, dB, max. Isolation, dB, min. VSWR , max. DC-3 GHz 3-6 GHz 6-12 GHz 12-15 GHz 15-18 GHz 0.2 0.2 0.5 0.5 0.5 70 70 60 60 60 1.25:1 1.25:1 1.5:1 1.5:1 1.5:1 For maximum limits, please see charts on page 3-5 PART NUMBERING SYSTEM CCS-37 S 1 C - T ** Series Options Connectors Actuator Type Actuator Voltage Connector S: SMA Female Actuator Voltage 1: 28 Vdc Failsafe 2: 15 Vdc Failsafe 3: 12 Vdc Failsafe 4: 24 Vdc Failsafe Actuator Type 0: Standard Contacts C: Indicator Contacts **SEE PARTS LIST ON PAGE 8 Options T: TTL Drivers with Diodes D: Transient Suppression Diodes M: Moisture Seal S: 9 Pin D-Sub Connector For other options, contact factory. (c) 2018 TELEDYNE RELAYS (800) 284-7007 * www.teledynecoax.com CCS-37S/CS-37S Page 1 CCS-37S\CS-37S\022018\Q1 Series CCS-37S/CS-37S COAX SWITCHES Miniature DC-18 GHz Failsafe TRANSFER Coaxial Switch SCHEMATICS AND MECHANICAL OUTLINE 1 6 "-s option" 9-pin d-P/N sub 2706650 connector (example: 9 PIN D-SUB PINOUT FOR FAILSAFE TRANSFER Pin No. 1 2 3 4 5 6 7 8 9 OPTIONS Basic Indicators + - + - CCS-37S/CS-37S Page 2 A B C TTL TRUTH TABLE (with TTL option) Logic Input Indicators & TTL 1 Vsw Common P/N 2707572 1 Vsw A B1 C611 RF Path Indicator (if applicable) 1 9 Common 1 ccs-37s10-s) 0 J1-J2 & J4-J3 B&C 1 J1-J3 & J4-J2 A&C 5 10 15 SPECIFICATIONS ARE AMPHENOL SUBJECT TO CHANGE WITHOUT NOTICE P/N P-17EHD-015P (c) 2019 TELEDYNE COAX SWITCHES CCS-37S\CS-37S\022018\Q1 Series CCS-37S/CS-37S COAX SWITCHES Miniature DC-18 GHz Failsafe TRANSFER Coaxial Switch TYPICAL NARROWBAND RF INSERTION LOSS PERFORMANCE CURVES Insertion Loss ( 5-10 GHz ) Insertion Loss ( DC-5 GHz ) 0 -0.1 -0.2 -0.2 Insertion Loss (dB) Insertion Loss (dB) 0 -0.1 -0.3 -0.4 -0.5 -0.6 -0.7 -0.8 -0.4 -0.5 -0.6 -0.7 -0.8 -0.9 -0.9 -1 -0.3 -1 0 1 2 3 4 5 5 6 7 Frequency (GHz) 9 10 Insertion Loss ( 13-15 GHz ) 0 0 -0.1 -0.1 -0.2 -0.2 Insertion Loss (dB) Insertion Loss (dB) Insertion Loss ( 10-13 GHz ) -0.3 -0.4 -0.5 -0.6 -0.7 -0.8 -0.9 -1 8 Frequency (GHz) -0.3 -0.4 -0.5 -0.6 -0.7 -0.8 -0.9 10 11 12 -1 13 13 14 Frequency (GHz) 15 Frequency (GHz) Insertion Loss ( 15-18 GHz ) 0 Insertion Loss (dB) -0.1 -0.2 -0.3 -0.4 -0.5 -0.6 -0.7 -0.8 -0.9 -1 15 TYPICAL 16 17 18 Frequency (GHz) MAXIMUM TEST LIMIT (c) 2018 TELEDYNE RELAYS (800) 284-7007 * www.teledynecoax.com CCS-37S/CS-37S Page 3 CCS-37S\CS-37S\022018\Q1 Series CCS-37S/CS-37S COAX SWITCHES Miniature DC-18 GHz Failsafe TRANSFER Coaxial Switch TYPICAL NARROWBAND RF ISOLATION PERFORMANCE CURVES Isolation ( 5-10 GHz ) 0 0 -20 -20 -40 -40 Isolation (dB) Isolation (dB) Isolation ( DC-5 GHz ) -60 -80 -100 -120 -140 -60 -80 -100 -120 0 1 2 3 4 -140 5 5 6 7 Frequency (GHz) 9 10 Isolation ( 13-15 GHz ) 0 0 -20 -20 -40 -40 Isolation (dB) Isolation (dB) Isolation ( 10-13 GHz ) -60 -80 -100 -120 -140 8 Frequency (GHz) -60 -80 -100 -120 10 11 12 -140 13 13 14 Frequency (GHz) 15 Frequency (GHz) Isolation ( 15-18 GHz ) 0 Isolation (dB) -20 -40 -60 -80 -100 -120 -140 15 16 17 18 Frequency (GHz) TYPICAL MAXIMUM TEST LIMIT CCS-37S/CS-37S Page 4 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE (c) 2019 TELEDYNE COAX SWITCHES CCS-37S\CS-37S\022018\Q1 Series CCS-37S/CS-37S COAX SWITCHES Miniature DC-18 GHz Failsafe TRANSFER Coaxial Switch TYPICAL NARROWBAND RF VSWR PERFORMANCE CURVES VSWR ( 5-10 GHz ) 2 2 1.9 1.9 1.8 1.8 1.7 1.7 1.6 1.6 VSWR VSWR VSWR ( DC-5 GHz ) 1.5 1.4 1.5 1.4 1.3 1.3 1.2 1.2 1.1 1.1 1 0 1 2 3 4 1 5 5 6 7 Frequency (GHz) 2 2 1.9 1.9 1.8 1.8 1.7 1.7 1.6 1.6 1.5 1.4 1.4 1.3 1.2 1.2 1.1 1.1 11 10 1.5 1.3 10 9 VSWR ( 13-15 GHz ) VSWR VSWR VSWR ( 10-13 GHz ) 1 8 Frequency (GHz) 12 1 13 13 14 Frequency (GHz) 15 Frequency (GHz) VSWR ( 15-18 GHz ) 2 1.9 1.8 VSWR 1.7 1.6 1.5 1.4 1.3 1.2 1.1 1 15 16 17 18 Frequency (GHz) TYPICAL MAXIMUM TEST LIMIT (c) 2018 TELEDYNE RELAYS (800) 284-7007 * www.teledynecoax.com CCS-37S/CS-37S Page 5 CCS-37S\CS-37S\022018\Q1 Series CCS-37S/CS-37S COAX SWITCHES Miniature DC-18 GHz Failsafe TRANSFER Coaxial Switch TYPICAL POWER PERFORMANCE CURVE Power Handling vs. Frequency 3000 2000 Power (W) 1000 800 600 400 STAN DAR DS 300 MA 200 SW ITC HES 100 80 60 40 30 20 10 .1 .2 .3 .4 .6 .8 1 2 4 6 8 10 18 Frequency GHz Estimates based on the following reference conditions: * Ambient temperature of 40C or less * Sea level operation * Load VSWR of 1.20:1 maximum * No high-power (hot) switching Please contact Teledyne Coax Switches for derating factors when applications do not meet the foregoing reference conditions. CCS-37S/CS-37S Page 6 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE (c) 2019 TELEDYNE COAX SWITCHES CCS-37S\CS-37S\022018\Q1 Series CCS-37S/CS-37S COAX SWITCHES Miniature DC-18 GHz Failsafe TRANSFER Coaxial Switch GLOSSARY Actuator An actuator is the electromechanical mechanism that transfers the RF contacts from one position to another upon DC command. TTL Switch Driver Option As a special option, switch drivers can be provided for both failsafe and latching switches, which are compatible with industry-standard low-power Schottky TTL circuits. Arc Suppression Diode A diode is connected in parallel with the coil. This diode limits the "reverse EMF spike" generated when the coil deenergizes to 0.7 volts. The diode cathode is connected to the positive side of the coil and the anode is connected to the negative side. Performance Parameters vs Frequency Generally speaking, the RF performance of coaxial switches is frequency dependent. With increasing frequency, VSWR and insertion loss increase while isolation decreases. All data sheets specify these three parameters as "worst case" at the highest operating frequency. If the switch is to be used over a narrow frequency band, better performance can be achieved. Date Code All switches are marked with either a unique serial number or a date code. Date codes are in accordance with MILSTD-1285 Paragraph 5.2.5 and consist of four digits. The first two digits define the year and the last two digits define the week of the year (YYWW). Thus, 1032 identifies switches that passed through final inspection during the 32nd week of 2010. Failsafe A failsafe switch reverts to the default or failsafe position when actuating voltage is removed. This is realized by a return spring within the drive mechanism. This type of switch requires the continuous application of operating voltage to select and hold any position. (Multi-position switches are normally open with no voltage applied). Indicator Indicators tell the system which position the switch is in. Other names for indicators are telemetry contacts or tellback circuit. Indicators are usually a set of internally mounted DC contacts linked to the actuator. They can be wired to digital input lines, status lights, or interlocks. Unless otherwise specified, the maximum indicator contact rating is 30 Vdc, 50 mA, or 1.5 Watts into a resistive load. Isolation Isolation is the measure of the power level at the output connector of an unconnected RF channel as referenced to the power at the input connector. It is specified in dB below the input power level. TRANSFER Switch A four-port switch consisting of two independent pairs of RF paths. These pairs are actuated simultaneously. This actuation is similar to that of a double-pole double-throw switch. Switching Time Switching time is the total interval beginning with the arrival of the leading edge of the command pulse at the switch DC input and ending with the completion of the switch transfer, including contact bounce. It consists of three parts: (1) inductive delay in the coil, (2) transfer time of the physical movement of the contacts, and (3) the bounce time of the RF contacts. (c) 2018 TELEDYNE RELAYS Actuator Current vs Temperature The resistance of the actuator coil varies as a function of temperature. There is an inverse relationship between the operating temperature of the switch and the actuator drive current. For switches operating at 28 VDC, the approximate actuator drive current at temperature, T, can be calculated using the equation: IT = IA [1 + .00385 (T-20)] Where: IT = Actuator current at temperature, T IA = Room temperature actuator current - see data sheet T = Temperature of interest in C Magnetic Sensitivity An electro-mechanical switch can be sensitive to ferrous materials and external magnetic fields. Neighboring ferrous materials should be permitted no closer than 0.5 inches and adjacent external magnetic fields should be limited to a flux density of less than 5 Gauss. SPECIAL FEATURE Switching High-Power or Highly Sensitive Signals Ensure the most linear response with the best galvanically matched contact system in the industry. Extremely low passive intermodulation is standard on all of our switches. Carrier Frequency 1 Carrier Frequency 2 PIM 3rd Order Frequency PIM 5th Order Frequency 870 MHz 893 MHz 847 MHz 824 MHz Transfer (800) 284-7007 * www.teledynecoax.com 3rd Order Intermodulation 5th Order Intermodulation -103 dBm -123 dBm -146 dBc -165 dBc CCS-37S/CS-37S Page 7 CCS-37S\CS-37S\022018\Q1 Series CCS-37S/CS-37S Miniature DC-18 GHz Failsafe TRANSFER Coaxial Switch COAX SWITCHES FAILSAFE CCS-37S/CS-37S PART NUMBER LIST Part No. * Part No. 1 CCS-37SXC 44 CS-37SX0-S 2 CCS-37SXC-D 45 CS-37SX0-T 3 CCS-37SXC-DM 46 CS-37SX0-TM 4 CCS-37SXC-DMS 47 CS-37SX0-TMS 5 CCS-37SXC-DS 48 CS-37SX0-TS 6 CCS-37SXC-M 7 CCS-37SXC-MS 8 CCS-37SXC-S 9 CCS-37SXC-T 10 CCS-37SXC-TM 11 CCS-37SXC-TMS 12 CCS-37SXC-TS 13 CCS-37SX0 14 CCS-37SX0-D 15 CCS-37SX0-DM 16 CCS-37SX0-DMS 17 CCS-37SX0-DS 18 CCS-37SX0-M 19 CCS-37SX0-MS 20 CCS-37SX0-S 21 CCS-37SX0-T 22 CCS-37SX0-TM 23 CCS-37SX0-TMS 24 CCS-37SX0-TS 25 CS-37SXC 26 CS-37SXC-D 27 CS-37SXC-DM 28 CS-37SXC-DMS 29 CS-37SXC-DS 30 CS-37SXC-M 31 CS-37SXC-MS 32 CS-37SXC-S 33 CS-37SXC-T 34 CS-37SXC-TM 35 CS-37SXC-TMS 36 CS-37SXC-TS 37 CS-37SX0 38 CS-37SX0-D 39 CS-37SX0-DM 40 CS-37SX0-DMS 41 CS-37SX0-DS 42 CS-37SX0-M 43 CS-37SX0-MS X = 1 (28Vdc), 2 (15Vdc), 3 (12Vdc) and 4 (24Vdc) CCS-37S/CS-37S Page 8 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE (c) 2019 TELEDYNE COAX SWITCHES CCS-37S\CS-37S\022018\Q1