3
Note :
ELECTRICAL CHARACTERISTICS
STYLE RC0201 RC0402 RC0603 RC0805 RC1206 RC1210 RC2010 RC2512
Power Rating @ 70°C 1/20W 1/16W 1/10W 1/8W 1/4W 1/3W 3/4W 1W
Operating Temp. Range -55°C ~ +125°C
Maximum Working Voltage 25V 50V 50V 150V 200V 200V 200V 200V
Maximum Overload Voltage 50V 100V 100V 300V 400V 400V 400V 400V
Dielectric Withstand Voltage 50V 100V 100V 300V 500V 500V 500V 500V
Resistance Range
E24Tol. ±2%, ±5% 10Ω ~ 1MΩ2Ω ~ 3.3MΩ1Ω ~ 22MΩ
E96Tol. ±0.5%, ±1% 100Ω ~ 2.2MΩ100Ω ~ 2.2MΩ
Zero Ohm Jumper<(0.05Ω)
TCR ±100ppm/°C– – 10Ω ~ 1MΩ
±200ppm/°C10Ω ~ 1MΩ10Ω ~ 3.3MΩ1Ω ~ 10Ω, >1MΩ
±400ppm/°C– 2Ω ~ 10Ω–
Jumper Criteria
Rated Current (A) 0.5 1.0 1.0 2.0 2.0 2.0 2.0 2.0
Maximum Current (A) @<1sec 1.0 2.0 2.0 5.0 10.0 10.0 10.0 10.0
ENVIRONMENTAL CHARACTERISTICS
PERFORMANCE TEST TEST METHOD 1% TOL. 5% TOL.
Temperature Coefficient MIL-STD-202F, Method 304 - 55°C to +125°Cby Type
Thermal Shock MIL-STD-202F, Method 107 5 Cycles, -55°C to +125°C (Step by Step 2 min.) ±(0.5%+0.05Ω)±(1%+0.05Ω)
Low Temperature Operation MIL-R-55342D, Para.4.7.4 One Hour at - 65°C Followed by 45 Minutes RCWV ±(0.5%+0.05Ω)±(1%+0.05Ω)
Short Time Overload MIL-R-55342D, Para.4.7.5 2.5 Times RCWV for 5 Seconds ±(1%+0.05Ω)±(2%+0.05Ω)
Insulation Resistance MIL-STD-202F, Method 302 RCOV for 1 Minute >10GΩ
Dielectric Withstand Voltage MIL-STD-202F, Method 301 R.M.S. for 1 Minute by Type
Resistance to Soldering Heat MIL-STD-202F, Method 210C Soldered to Test Board at 260°C for 10 Seconds ±(0.5%+0.05Ω)±(1%+0.05Ω)
Moisture Resistance MIL-STD-202F, Method 106F 42 Cycles. Total 1000 Hours ±(0.5%+0.05Ω)±(2%+0.05Ω)
Life MIL-STD-202F, Method 108A 1000 Hours at 70°C RCWV Intermittent ±(1%+0.05Ω)±(3%+0.05Ω)
Solderability MIL-STD-202F, Method 208G 230°C for 5 Seconds >95% Coverage
Bending Strength JIS-C-5202, Para.6.1.4, Unit Mounted in Center of 90mm Board Length, ±(1%+0.05Ω)±(1%+0.05Ω)
Deflected 5mm (power chip 2mm) in Either Direction for 5 Seconds
2